Search Results

Search found 23762 results on 951 pages for 'network speed'.

Page 374/951 | < Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >

• Megacli is killing me, any help appreciated

  - by Stefan

  I run a server with 2 drives in raid0 configured through BIOS. I just added 2 more drives using hotplug (the server is dell r610 with RHEL 5.4 64bit) and I would like to configure a separate raid0 partition on these drives. I am getting the following error: /opt/MegaRAID/MegaCli/MegaCli64 -CfgLdAdd r0[32:2, 32:3] -a0 The specified physical disk does not have the appropriate attributes to complete the requested command. Exit Code: 0x26 All the parameters are correct and there is just no reason why this command could not work, see this (fujitsu is current raid, seagate is the new one I want to create): /opt/MegaRAID/MegaCli/MegaCli64 -PDList -aALL | egrep 'Adapter|Enclosure|Slot|Inquiry' Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA101174 Enclosure Device ID: 32 Slot Number: 1 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA10115T Enclosure Device ID: 32 Slot Number: 2 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS033SE0TF5K Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS023SE070FK I also tried to set up the drive as hotspare, also some strange error: /opt/MegaRAID/MegaCli/MegaCli64 -PDHSP -Set -physdrv[32:3] -a0 Adapter: 0: Set Physical Drive at EnclId-32 SlotId-3 as Hot Spare Failed. FW error description: The specified device is in a state that doesn't support the requested command. Exit Code: 0x32 As you can see the disk is in Unconfigured, Good state: Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Device Id: 3 Sequence Number: 1 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.875 GB [0x22dc0000 Sectors] Firmware state: Unconfigured(good), Spun Up SAS Address(0): 0x5000c50005cd20b1 SAS Address(1): 0x0 Connected Port Number: 3(path0) Inquiry Data: SEAGATE ST9300603SS FS023SE070FK FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: Foreign Foreign Secure: Drive is not secured by a foreign lock key Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :30C (86.00 F)

  Read the article

• 4in6 tunneling (via OpenVPN?)

  - by Deshene

  I have a local network with internet access. But unfortunately IPv4 internet connection speed is limited to 1mbps, which is realy sad. Fortunately I have a native IPv6, and there is no connection speed limit over IPv6. So, in order to get a good internet connection I made a plan: connect to the VPN-service over IPv6, and pass all IPv4 traffic through IPv6 tunnel, or something like that, I think you get the idea. I suggested to use service like HideMyAss.com, but unfortunately they don't support IPv6. The question is: Is there any existing VPN service that will make my dreams come true, and is easy to use, which I could connect over PPTP or OpenVPN (I want to set up connection to VPN in my router settings). Edit: It seems like there are couple of VPN services that supports IPv6 (it's odd, but the biggest VPN services support only IPv4), and there is none providing 4in6 tunnels. So, I came to the following solution: rent a VPS with IPv6 address, and manually setup 4in6 tunnel. I'm not good at networking, never did things like that, and don't know where to start, and what should I do. The use case, as I undestand, should look like this: I connect from my home computer to the VPS via OpenVPN, and after that all my IPv4 traffic pass through IPv6 (server do the job). OpenVPN - because I want to configure VPN connection to server in my router (Asus RT-N16?). How can I achieve this?

  Read the article

• raid md device is not remove from memory, how to overcome this problem

  - by santhosha

  i create raid 10 , i removed two arrays form md11 one by one , after that i going to editing the contents those are mounted ( it will be not responding stage), after i try for remove arrays those are left it is shows device or resource busy ( is not removed from memory). i try to terminate process this is also not work, i absorve from 4 days resync will be 8.0% it can not modifying. cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec mdadm -D /dev/md11 /dev/md11: Version : 00.90.03 Creation Time : Sun Jan 16 16:20:01 2011 Raid Level : raid10 Array Size : 286743936 (273.46 GiB 293.63 GB) Device Size : 143371968 (136.73 GiB 146.81 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 11 Persistence : Superblock is persistent Update Time : Sun Jan 16 16:56:07 2011 State : active, degraded, resyncing Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K Rebuild Status : 8% complete UUID : 5e124ea4:79a01181:dc4110d3:a48576ea Events : 0.23 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 4 8 145 2 faulty spare rebuilding /dev/sdj1 3 8 65 3 active sync /dev/sde1 umount /dev/md11 umount: /dev/md11: not mounted mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 kill -9 2128 kill -9 5018 kill -9 27605 kill -9 30562 kill -3 30591 mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec

  Read the article

• How do Opera's keyboard shortcut settings work?

  - by zem

  Firefox 4 beta is starting to freeze up the way Firefox 3 used to on my machine, and I want a browser that'll play gifs at full speed, so on a Mac my only other choice seems to be Opera. There are just two issues I have with it right now: one, the scrolling is weird compared to every other Mac application, but I can get used to that if there's no way to fix it. Two, cmd-1 through cmd-9 activate the "speed dial" bookmarks instead of selecting tabs 1-9, like in Firefox and Chrome. I can disable those shortcuts easily enough, so I don't keep accidentally loading a different page when I instinctively try to do that, but in an ideal world I could remap those commands to do what I want. The keyboard shortcut editor is weird: There seems to be a scrappy little language for associating actions with commands. It has some limited autocompletion when you type stuff in, and I couldn't find a "select specific tab" action, but some of the existing commands are complicated enough that I'd be surprised if there's not a way to do it. Is there documentation for this language anywhere? Clicking "help" just brings me to this page, which is not very helpful.

  Read the article

• Can I upgrade the CPU in my Lenovo 3000 N100 laptop?

  - by Pavel

  I've got an Intel Core Duo T2300 in my laptop (Lenovo 3000 N100, 0768-49G). Here is what I could find out about it: $ sudo dmidecode # dmidecode 2.11 SMBIOS 2.4 present. 42 structures occupying 1436 bytes. Table at 0x000DC010. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: LENOVO Version: 61ET37WW Release Date: 06/04/07 Address: 0xE6B70 [...] Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: LENOVO Product Name: CAPELL VALLEY(NAPA) CRB [...] Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: U2E1 Type: Central Processor Family: Other Manufacturer: Intel ID: E8 06 00 00 FF FB E9 BF Version: Genuine Intel(R) CPU T2300 @ 1.66GHz Voltage: 3.3 V External Clock: 166 MHz Max Speed: 2048 MHz Current Speed: 1600 MHz Status: Populated, Enabled Upgrade: ZIF Socket L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified $ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 14 model name : Genuine Intel(R) CPU T2300 @ 1.66GHz stepping : 8 microcode : 0x39 cpu MHz : 1000.000 cache size : 2048 KB I believe the chipset is "Mobile Intel 945GM Express", but I don't know how to verify it on a Linux system. I'm not sure about the socket, but Intel claims "Sockets Supported: PBGA479, PPGA478". Now, I'd like to upgrade to the fastest compatible CPU available, but I'm a bit lost in all the details. Can you guys help me out with a couple of questions, please? What CPUs can I choose from? (I think it's only the Core2Duo line, but it should be enough for an upgrade) Can I use a 64-bit CPU? Can I use a CPU with a higher FSB than 667 MHz? Do I have to worry about additional cooling, or is it enough to check for similar voltage/TDP values? Thank you!

  Read the article

• Strange performance issue with Dell R7610 and LSI 2208 RAID controller

  - by GregC

  Connecting controller to any of the three PCIe x16 slots yield choppy read performance around 750 MB/sec Lowly PCIe x4 slot yields steady 1.2 GB/sec read Given same files, same Windows Server 2008 R2 OS, same RAID6 24-disk Seagate ES.2 3TB array on LSI 9286-8e, same Dell R7610 Precision Workstation with A03 BIOS, same W5000 graphics card (no other cards), same settings etc. I see super-low CPU utilization in both cases. SiSoft Sandra reports x8 at 5GT/sec in x16 slot, and x4 at 5GT/sec in x4 slot, as expected. I'd like to be able to rely on the sheer speed of x16 slots. What gives? What can I try? Any ideas? Please assist Cross-posted from http://en.community.dell.com/support-forums/desktop/f/3514/t/19526990.aspx Follow-up information We did some more performance testing with reading from 8 SSDs, connected directly (without an expander chip). This means that both SAS cables were utilized. We saw nearly double performance, but it varied from run to run: {2.0, 1.8, 1.6, and 1.4 GB/sec were observed, then performance jumped back up to 2.0}. The SSD RAID0 tests were conducted in a x16 PCIe slot, all other variables kept the same. It seems to me that we were getting double the performance of HDD-based RAID6 array. Just for reference: maximum possible read burst speed over single channel of SAS 6Gb/sec is 570 MB/sec due to 8b/10b encoding and protocol limitations (SAS cable provides four such channels).

  Read the article

• Low CPU performance with low usage and clock - Windows 8.1

  - by Daniele

  I recently deleted everything from my PC and reinstalled Windows 8.1 from scratch. When I first booted into Windows everything was extremely slow though the CPU usage was very low (about 1%). After installing some drivers the problem seemed to be solved, I was able to use my PC normally. Today I installed a game and I noticed a strange behavior: the game was playable but the performance worsened more and more in the time. This is the situation BEFORE opening the game (normal): This is AFTER some minutes inside the game (low CPU usage and clock): Some information about my system: PC: Sony Vaio S13 (SVS13A1C5E) OS: Windows 8.1 CPU: Intel Core i7-3520M 2.90GHz GPU(1): Intel HD Graphics 4000 GPU(2): NVIDIA GeForce GT 640M LE I tried searching for new drivers and other solutions but noting worked and I don't know what is the cause. I did not checked the temperatures but the fans are not running fast and the PC does not look overheated. Update: Max CPU Temp: 66°C, Max GPU Temp: 61°C The strange thing is that the GPU load is 99% (GPU-Z) and the fan is almost silent. Update 2: I had troubles with Sony Vaio software, I can't get the FN keys and the STAMINA/SPEED switch to work (it is a physical switch to enable/disable the Nvidia card and change the Power Profile). I'm saying this because I remember that before reinstalling Windows there was an option in the Vaio Control Center (now it is not there anymore) that allowed me to choose from something like "priority to performance (ventilation)" or "priority to silence". The current behavior looks like a "priority to silence", but I can't get the stamina-speed switch to work and so I don't see similar oprions in the Vaio Control Center. I don't know if the problem is related to this.

  Read the article

• Disabling CPU management

  - by Tiffany Walker

  If I add the following processor.max_cstate=0 to the kernel command line for boot up, does that disable all CPU power management and throttling? I also found: http://www.experts-exchange.com/OS/Linux/Administration/A_3492-Avoiding-CPU-speed-scaling-in-modern-Linux-distributions-Running-CPU-at-full-speed-Tips.html The link talks of Change CPU governor from 'ondemand' to 'performance' for all CPUs/cores and disabling kondemand from kernel. Server is for web hosting UPDATES: 2.6.32-379.1.1.lve1.1.7.6.el6.x86_64 #1 SMP Sat Aug 4 09:56:37 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux . # dmidecode 2.11 SMBIOS 2.6 present. 74 structures occupying 2878 bytes. Table at 0x0009F000. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: American Megatrends Inc. Version: 1.0c Release Date: 05/27/2010 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 4096 kB Characteristics: ISA is supported PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Targeted content distribution is supported BIOS Revision: 8.16 Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: 0123456789 UUID: 49434D53-0200-9033-2500-33902500D52C Wake-up Type: Power Switch SKU Number: To Be Filled By O.E.M. Family: To Be Filled By O.E.M. Handle 0x0002, DMI type 2, 15 bytes Base Board Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: VM11S61561 Asset Tag: To Be Filled By O.E.M. Features: Board is a hosting board Board is replaceable Location In Chassis: To Be Filled By O.E.M. Chassis Handle: 0x0003 Type: Motherboard Contained Object Handles: 0 Handle 0x0003, DMI type 3, 21 bytes Chassis Information Manufacturer: Supermicro Type: Sealed-case PC Lock: Not Present Version: 0123456789 Serial Number: 0123456789 Asset Tag: To Be Filled By O.E.M. Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000 Height: Unspecified Number Of Power Cords: 1 Contained Elements: 0

  Read the article

• VRF Internet Gateway Multiple External IP's 1 Internal IP to AWS

  - by user223903

  Trying to setup VRF for the first time and its not working for me even though I keep reading everything online. IP's are different to real life. I have an Internet connection which I can ping to my router in the current setup below 195.45.73.22 I have a block of ip addresses 195.45.121.0/27 I want to setup multiple VPN's to AWS so need to have multiple external ip's thus the block of IP addresses. I have setup the 2nd and 3rd IP address but can not ping them from external. Any help would be grateful. Bryan ip source-route ! ip vrf Internet rd 1:1 route-target export 1:1 route-target import 1:1 ip vrf AWSSydney1 rd 2:2 route-target export 2:2 route-target import 2:2 route-target import 1:1 ip vrf AWSSydney2 rd 3:3 route-target export 3:3 route-target import 3:3 route-target import 1:1 ip cef no ip domain lookup no ipv6 cef multilink bundle-name authenticated interface FastEthernet0/0 description Vocus Internet no ip address speed 100 full-duplex interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 195.45.73.22 255.255.255.252 interface FastEthernet0/0.2 encapsulation dot1Q 2 ip vrf forwarding AWSSydney1 ip address 195.45.121.1 255.255.255.224 interface FastEthernet0/0.3 encapsulation dot1Q 3 ip vrf forwarding AWSSydney2 ip address 195.45.121.2 255.255.255.224 interface FastEthernet0/1 description LAN_SIDE ip address 10.0.0.5 255.255.255.0 speed 100 full-duplex no mop enabled ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 195.45.73.21 ip route vrf Internet 0.0.0.0 0.0.0.0 195.45.73.21

  Read the article

• Bash Script - Traffic Shaping

  - by Craig-Aaron

  hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

  Read the article

• Kernel panic while loading Mac OS X on VMWare

  - by Vladimir Gritsenko

  I'm trying to run Mac OS X 10.6.3 on VMWare 7.1 from within Windows 7 64 bit. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem.

  Read the article

• Strange performance differences in read/write from/to USB flash drive

  - by Mario De Schaepmeester

  When copying files from my 8GB USB 2.0 flash drive with Windows 7 to a traditional hard drive, the average speed is between 25 and 30 MB/s. When doing the reverse, copying to the USB drive, the speed is 5MB/s average. I have tested this with about 4.5GB of files, a mixture of smaller and larger ones. The observations were the same on both FAT32 and exFAT file systems on the USB drive, NTFS on the internal hard disk. I don't think I can be mistaken in saying that flash memory has a lot higher performance than a spinning hard drive in both terms of reading and writing. For both memory types, reading should be faster than writing too. Now I wonder, how can it be that copying files from a fast read memory to a faster write memory is actually slower than copying files from a fast read memory to a slow write memory? I think that the files are stored in RAM before being copied over too, and there's caching as well, but I don't see how even that could tip the balance. It can only be in the advantage of writing to the USB drive, since it is "closer" to the SATA system than the USB port and it will receive data from the internal SATA HDD faster. Perhaps my way of thinking is all wrong or it just depends on the manufacturer of the USB pen. But I am curious.

  Read the article

• What benchmark tool to use to benchmark hardware for VM server?

  - by Mark0978

  We are setting up a new piece of hardware to virtualize several of our servers on. Choices are RAID 5, RAID 6, and RAID 0+1. We are wanting to benchmark all three before we go live with the machine, but I'm not sure how to test the speed. Since we will be using it to host VMs, what will the actual disk traffic look like? What can I use to see if RAID 6 is too slow? Short of setting up the system with all the VM's on it and running that way, then redoing on all the work, I'm not sure how to test it. It them becomes more of a subjective test than an objective one. I'm worried that RAID6 will have too much overhead, that RAID5 will be to fragile with 3TB drives and I've never worked with 0+1 at all. So in short I'd like to setup the base machine (which will be running Linux) and then test the underlying SW RAID for speed. What kind of tool exists to simulate this kind of load? Barring the lack of a specific tool, how about a generic FS testing tool that will simulate different loads?

  Read the article

• LTO 2 tape performance in LTO 3 drive

  - by hmallett

  I have a pile of LTO 2 tapes, and both an LTO 2 drive (HP Ultrium 460e), and an autoloader with an LTO 3 drive in (Tandberg T24 autoloader, with a HP drive). Performance of the LTO 2 tapes in the LTO 2 drive is adequate and consistent. HP L&TT tells me that the tapes can be read and written at 64 MB/s, which seems in line with the performance specifications of the drive. When I perform a backup (over the network) using Symantec Backup Exec, I get about 1700 MB/min backup and verify speeds, which is slower, but still adequate. Performance of the LTO 2 tapes in the LTO 3 drive in the autoloader is a different story. HP L&TT tells me that the tapes can be read at 82 MB/s and written at 49 MB/s, which seems unusual at the write speed drop, but not the end of the world. When I perform a backup (over the network) using Symantec Backup Exec though, I get about 331 MB/min backup speed and 205 MB/min verify speeds, which is not only much slower, but also much slower for reads than for writes. Notes: The comparison testing was done on the same server, SCSI card and SCSI cable, with the same backup data set and the same tape each time. The tape and drives are error-free (according to HP L&TT and Backup Exec). The SCSI card is a U160 card, which is not normally recommended for LTO 3, but we're not writing to LTO 3 tapes at LTO 3 speeds, and a U320 SCSI card is not available to me at the moment. As I'm scratching my head to determine the reason for the performance drop, my first question is: While LTO drives can write to the previous generation LTO tapes, does doing so normally incur a performance penalty?

  Read the article

• XAMPP CURL not working!

  - by MiffTheFox

  Nope, it's not. Windows Vista Home Premium x32: Relevant section of php.ini: ; Windows Extensions ; Note that ODBC support is built in, so no dll is needed for it. ; Note that many DLL files are located in the extensions/ (PHP 4) ext/ (PHP 5) ; extension folders as well as the separate PECL DLL download (PHP 5). ; Be sure to appropriately set the extension_dir directive. ;extension=php_apc.dll ;extension=php_apd.dll ;extension=php_bcompiler.dll ;extension=php_bitset.dll ;extension=php_blenc.dll ;extension=php_bz2.dll ;extension=php_bz2_filter.dll ;extension=php_classkit.dll ;extension=php_cpdf.dll ;extension=php_crack.dll extension=php_curl.dll ;extension=php_cvsclient.dll ;extension=php_db.dll ;extension=php_dba.dll ;extension=php_dbase.dll ;extension=php_dbx.dll Proof it's not working: c:\users\miff>curl http://localhost/xampp/phpinfo.php | grep curl % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 62592 0 62592 0 0 1971k 0 --:--:-- --:--:-- --:--:-- 3319k <tr><td class="e">HTTP_USER_AGENT </td><td class="v">curl/7.16.3 (i686-pc-cygwin) libcurl/7.16.3 OpenSSL/0.9.8k zlib/1.2.3 libssh2/0.15-CVS </td></tr> <tr><td class="e">User-Agent </td><td class="v">curl/7.16.3 (i686-pc-cygwin) libcurl/7.16.3 OpenSSL/0.9.8k zlib/1.2.3 libssh2/0.15-CVS </td></tr> <tr><td class="e">_SERVER["HTTP_USER_AGENT"]</td><td class="v">curl/7.16.3 (i686-pc-cygwin) libcurl/7.16.3 OpenSSL/0.9.8k zlib/1.2.3 libssh2/0.15-CVS</td></tr> c:\users\miff>

  Read the article

• Flash alternative for iBook Mac?

  - by Hunter Dolan

  I have a old Apple iBook G4 that I decided to hook up to my main TV. I like the setup because I can surf the internet on my TV now. The only thing that I can't seem to do is watch Flash videos. Apparently Flash Player 10 doesn't play nice with the iBook's graphics card's GPU, leaving all the graphics processing to the CPU which is a disaster. Others suggested downgrading to Flash Player 9, I did that, and youtube worked fine, but Hulu (The main reason I wanted to hook it up to the TV in the first place) did not. Anyone know of a Flash alternative or a Flash 10 fix for the iBook? Or even a Hulu client that doesn't require Flash. Here are my iBook's Specs Model Name: iBook G4 <br> Model Identifier: PowerBook6,5 <br> Processor Name: PowerPC G4 (1.2) <br> Processor Speed: 1.2 GHz <br> Number Of CPUs: 1 <br> L2 Cache (per CPU): 512 KB <br> Memory: 512 MB <br> Bus Speed: 133 MHz <br> Boot ROM Version: 4.8.7f1 <br> Mac OS X Version: 10.5.8 <br> PS: Don't tell me that I need to buy a new computer. I know that I would have better results with a new computer but I don't want to buy a new computer just for Hulu.

  Read the article

• Hints on diagnosing performance issue in OpenBSD firewall

  - by Tom

  My OpenBSD 4.6 pf firewall has started having really bad performance in the past few weeks. I've isolated the firewall (as opposed to the WAN connection, switch, cable, etc.) as the problem, but need a hint on how to further diagnose or fix the problem. The facts: Normal setup is: DSL Modem - FW Ext. NIC - FW Int. NIC - Switch - Laptop Normal setup described above gives only 25 Kbps! Plugging the laptop straight from the DSL modem gives a 1 MBps connection (full speed, as advertised). Therefore, the DSL connection seems to be OK. Plugging the laptop directly into the firewall's internal NIC (bypassing the switch) also gives only 25 Kbps. Therefore, the switch does not seem to be a problem. I've replaced the ethernet cables, but it didn't help. Here's the weird thing. Reloading the ruleset (/sbin/pfctl -Fa -f /etc/pf.conf) causes the laptop's connection to go up to 1 Mbps (i.e. full speed) for a few minutes before it gradually degrades back down to 25Kbps again. Any ideas on what's wrong or how I could further diagnose the problem?

  Read the article

• Best CPUs for speeding up compiling times of C++ w/ DistGCC

  - by Jay

  I'm putting together a distributed build farm with DistGCC to speed up our teams compile times and just looking for thoughts on which processors to use in the hosts. Are we going to get a noticeable decrease in time using 8 cores vs. 4-hyperthreaded cores? Big difference in time between i7 and Xeon? etc, etc. Just need advice from people who've put together kick-a build clusters. We've got a majority of the normal things to speed up builds in place (pre-compiled headers, ccache, local gigabit connections between them, tons of ram, etc) so please just give advice on the best processor to use. And money is a factor, but anythings doable if the performance increase is noticeable. Thanks. Jay EDIT: Although any advice IS welcome, please refrain from "Do this first" posts as we're not planning on skimping on things like SSD, maxed out RAM, etc. My personal system is a iMac Quad-core i5 with 8GB of RAM. When I build our project locally, my processor floats around 99-100% a majority of the time, which makes me assume it is a bottleneck, even if you made everything else faster. My ram on the other hand doesn't even get close to maxing out. It's also worth noting that I did research this, however every discussion I could find was primarily for gaming machines, which is obviously a different beast in usage. These machines won't even have monitors or anything but integrated graphics since they have one purpose: Build freakin fast. (hopefully)

  Read the article

• Best CPUs for speeding up compiling times of C++ w/ DistGCC

  - by Jay

  I'm putting together a distributed build farm with DistGCC to speed up our teams compile times and just looking for thoughts on which processors to use in the hosts. Are we going to get a noticeable decrease in time using 8 cores vs. 4-hyperthreaded cores? Big difference in time between i7 and Xeon? etc, etc. Just need advice from people who've put together kick-a build clusters. We've got a majority of the normal things to speed up builds in place (pre-compiled headers, ccache, local gigabit connections between them, tons of ram, etc) so please just give advice on the best processor to use. And money is a factor, but anythings doable if the performance increase is noticeable. Thanks. Jay EDIT: Although any advice IS welcome, please refrain from "Do this first" posts as we're not planning on skimping on things like SSD, maxed out RAM, etc. My personal system is a iMac Quad-core i5 with 8GB of RAM. When I build our project locally, my processor floats around 99-100% a majority of the time, which makes me assume it is a bottleneck, even if you made everything else faster. My ram on the other hand doesn't even get close to maxing out. It's also worth noting that I did research this, however every discussion I could find was primarily for gaming machines, which is obviously a different beast in usage. These machines won't even have monitors or anything but integrated graphics since they have one purpose: Build freakin fast. (hopefully)

  Read the article

• Best CPUs for speeding up compiling times of C++ w/ DistGCC

  - by Jay

  I'm putting together a distributed build farm with DistGCC to speed up our teams compile times and just looking for thoughts on which processors to use in the hosts. Are we going to get a noticeable decrease in time using 8 cores vs. 4-hyperthreaded cores? Big difference in time between i7 and Xeon? etc, etc. Just need advice from people who've put together kick-a build clusters. We've got a majority of the normal things to speed up builds in place (pre-compiled headers, ccache, local gigabit connections between them, tons of ram, etc) so please just give advice on the best processor to use. And money is a factor, but anythings doable if the performance increase is noticeable. Thanks. Jay EDIT: Although any advice IS welcome, please refrain from "Do this first" posts as we're not planning on skimping on things like SSD, maxed out RAM, etc. My personal system is a iMac Quad-core i5 with 8GB of RAM. When I build our project locally, my processor floats around 99-100% a majority of the time, which makes me assume it is a bottleneck, even if you made everything else faster. My ram on the other hand doesn't even get close to maxing out. It's also worth noting that I did research this, however every discussion I could find was primarily for gaming machines, which is obviously a different beast in usage. These machines won't even have monitors or anything but integrated graphics since they have one purpose: Build freakin fast. (hopefully)

  Read the article

• Can't connect to samba

  - by Rick

  Windows 7, connecting to Samba shares I have a follow up question from the link above. I am running Samba 3.0.23d on FreeBSD is release 7.1 I changed the policies as described above but still cannot connect to the samba server with the windows 7 or a server 2008. I feel it is a problem with recognizing the new machines on the network. the windows machines can see the samba server, but cannot connect to it or view any of the files. After changing the security policies the samba server asked for network id and password but would not allow the machine to connect, said they were unknown username or bad password. Here is my current config file. there is no sign of encryption anywhere, should I just add the line? not sure what that would do elsewhere. Workgroup = WWOFFSET server string = WWO File Server (%v) security = server username map = /usr/local/etc/smb.users hosts allow = 10. 127. # If you want to automatically load your printer list rather # than setting them up individually then you'll need this ; load printers = yes # you may wish to override the location of the printcap file ; printcap name = /etc/printcap # on SystemV system setting printcap name to lpstat should allow # you to automatically obtain a printer list from the SystemV spool # system ; printcap name = lpstat # It should not be necessary to specify the print system type unless # it is non-standard. Currently supported print systems include: # bsd, cups, sysv, plp, lprng, aix, hpux, qnx ; printing = cups # Uncomment this if you want a guest account, you must add this to /etc/passwd # otherwise the user "nobody" is used ; guest account = pcguest # this tells Samba to use a separate log file for each machine # that connects log file = /var/log/samba/log.%m # Put a capping on the size of the log files (in Kb). max log size = 50 # Use password server option only with security = server # The argument list may include: # password server = My_PDC_Name [My_BDC_Name] [My_Next_BDC_Name] # or to auto-locate the domain controller/s # password server = * ; password server = <NT-Server-Name> password server = SERVER0 # Use the realm option only with security = ads # Specifies the Active Directory realm the host is part of ; realm = MY_REALM # Backend to store user information in. New installations should # use either tdbsam or ldapsam. smbpasswd is available for backwards # compatibility. tdbsam requires no further configuration. ; passdb backend = tdbsam ; passdb backend = smbpasswd # Using the following line enables you to customise your configuration # on a per machine basis. The %m gets replaced with the netbios name # of the machine that is connecting. # Note: Consider carefully the location in the configuration file of # this line. The included file is read at that point. ; include = /usr/local/etc/smb.conf.%m # Most people will find that this option gives better performance. # See the chapter 'Samba performance issues' in the Samba HOWTO Collection # and the manual pages for details. # You may want to add the following on a Linux system: # SO_RCVBUF=8192 SO_SNDBUF=8192 socket options = TCP_NODELAY # Configure Samba to use multiple interfaces # If you have multiple network interfaces then you must list them # here. See the man page for details. ; interfaces = 192.168.12.2/24 192.168.13.2/24 # Browser Control Options: # set local master to no if you don't want Samba to become a master # browser on your network. Otherwise the normal election rules apply ; local master = no # OS Level determines the precedence of this server in master browser # elections. The default value should be reasonable ; os level = 33 # Domain Master specifies Samba to be the Domain Master Browser. This # allows Samba to collate browse lists between subnets. Don't use this # if you already have a Windows NT domain controller doing this job ; domain master = yes # Preferred Master causes Samba to force a local browser election on startup # and gives it a slightly higher chance of winning the election ; preferred master = yes # Enable this if you want Samba to be a domain logon server for # Windows95 workstations. ; domain logons = yes # if you enable domain logons then you may want a per-machine or # per user logon script # run a specific logon batch file per workstation (machine) ; logon script = %m.bat # run a specific logon batch file per username ; logon script = %U.bat # Where to store roving profiles (only for Win95 and WinNT) # %L substitutes for this servers netbios name, %U is username # You must uncomment the [Profiles] share below ; logon path = \\%L\Profiles\%U # Windows Internet Name Serving Support Section: # WINS Support - Tells the NMBD component of Samba to enable it's WINS Server ; wins support = yes # WINS Server - Tells the NMBD components of Samba to be a WINS Client # Note: Samba can be either a WINS Server, or a WINS Client, but NOT both ; wins server = w.x.y.z # WINS Proxy - Tells Samba to answer name resolution queries on # behalf of a non WINS capable client, for this to work there must be # at least one WINS Server on the network. The default is NO. ; wins proxy = yes # DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names # via DNS nslookups. The default is NO. dns proxy = no # charset settings ; display charset = ASCII ; unix charset = ASCII ; dos charset = ASCII # These scripts are used on a domain controller or stand-alone # machine to add or delete corresponding unix accounts ; add user script = /usr/sbin/useradd %u ; add group script = /usr/sbin/groupadd %g ; add machine script = /usr/sbin/adduser -n -g machines -c Machine -d /dev/null -s /bin/false %u ; delete user script = /usr/sbin/userdel %u ; delete user from group script = /usr/sbin/deluser %u %g ; delete group script = /usr/sbin/groupdel %g unix extensions = no

  Read the article

• What LTO 4 drive to buy

  - by pplrppl

  Evan Anderson mentioned in another solution you could buy a LTO-4 (autoloader, 1 tape / day) - $4,566.00 (the discussion included total cost of tapes for a specific rotation.) but I don't know specifics on what he or you would recommend for the actual drive and if necessary controller. Show me a newegg URL or CDW, Dell, or HP, or whatever your favorite vendor would be for your solution if you don't mind looking it up or just give me a brand and a model number and I'll be glad to do the leg work myself. I currently have on have on hand an external LTO 3 drive that uses LVD SCSI interface (and thus have a controller card that has an external LVD SCSI connector). If that card isn't sufficient to interface to a LTO 4 drive let me know. http://www.fujifilmusa.com/shared/bin/LTO_Overview.pdf shows minimum tape speeds for LTO4 and other LTO formats. It looks like the IBM LTO4 actually has a lower minimum speed than the IBM LTO3. Either way my average server is too slow to feed LTO3/4 without shoeshining so I'm looking for a drive with a low minimum write speed. If you trust the PDF from 2008 that makes my choices IBM LTO 4 full height IBM LTO 4 half height HP LTO 4 half height but presumably there are other options out there that weren't mentioned in the fuji PDF. Again I'm looking for a specific recommendation on a drive to buy (and the controller if needed).

  Read the article

• Does fast typing influence fast programming?

  - by Lukasz Lew

  Many young programmers think that their bottleneck is typing speed. After some experience one realizes that it is not the case, you have to think much more than type. At some point my room-mate forced me to turn of the light (he sleeps during the night). I had to learn to touch type and I experienced an actual improvement in programming skill. The most surprising was that the improvement not due to sheer typing speed, but to a change in mindset. I'm less afraid now to try new things and refactor them later if they work well. It's like having a new tool in the bag. Have anyone of you had similar experience? Now I trained a touch typing a little with KTouch. I find auto-generate lessons the best. I can use this program to create new lessons out of text files but it's only verbatim training, not auto-generated based on a language model. Do you know any touch typing program that allows creation of custom, but randomized lessons?

  Read the article

• Speeding up Outlook Express on Windows XP over satellite

  - by John

  My brother is in the field with Doctors Without Borders. I'm posting this question on his behalf. We use outlook express (on a pc running windows XP) and a 9600 baud dial up satellite phone modem to get our email direct from the server in Paris. As this is a very expensive way to communicate (our satellite bill is $50K a year, no joke), it seems like trying to streamline is a good idea. Here's the question- when we connect, the sequence goes: Send outbox mails. This goes pretty quickly, probably 10-15 seconds for each email, up to maybe a couple minutes for an email of 150k or so). The status bar moves pretty quickly, according to the emails sent. The system then says "Checking for new messages on (our account name), and "Receiving list of messages from server". This takes a long time. Like 10-15 minutes. The status bar crawls along. Then it receives the messages. "Receiving messages from server". Again, each message takes 10-15 seconds, and this part moves along reasonably fast. I'm curious as to what is going on in the second part. It takes forever, and doesn't seem to be part of the sending or receiving messages themselves. Is there a way to speed up the process by changing a preference with communicating with the server or something? Does anyone have any advice for him speeding up what Outlooks Express is doing? Obviously his software is ancient and adding more software is not realistic based on the connection speed. Thanks!

  Read the article

< Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >