Search Results

Search found 981 results on 40 pages for '015 lo'.

Page 38/40 | < Previous Page | 34 35 36 37 38 39 40  | Next Page >

• Bonding: works only for download

  - by Crazy_Bash

  I would like to install bonding with 4 links with mode 4. but only "download/receiving" works with bondig. for transmitting the system chooses one link. ifconfig bond0 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 inet addr:ip Bcast:ip Mask:255.255.255.248 inet6 addr: fe80::92e2:baff:fe0f:76b4/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:239187413 errors:0 dropped:10944 overruns:0 frame:0 TX packets:536902370 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14688536197 (13.6 GiB) TX bytes:799521192901 (744.6 GiB) eth2 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:54969488 errors:0 dropped:0 overruns:0 frame:0 TX packets:2537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3374778591 (3.1 GiB) TX bytes:314290 (306.9 KiB) eth3 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:64935805 errors:0 dropped:1 overruns:0 frame:0 TX packets:2532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3993499746 (3.7 GiB) TX bytes:313968 (306.6 KiB) eth4 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:57352105 errors:0 dropped:2 overruns:0 frame:0 TX packets:536894778 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3524236530 (3.2 GiB) TX bytes:799520265627 (744.6 GiB) eth5 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:61930025 errors:0 dropped:3 overruns:0 frame:0 TX packets:2540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3796021948 (3.5 GiB) TX bytes:314274 (306.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5320 (5.1 KiB) TX bytes:5320 (5.1 KiB) those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 1 Number of ports: 4 Actor Key: 17 Partner Key: 11 Partner Mac Address: 00:24:51:12:63:00 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b4 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b5 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b6 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b7 Aggregator ID: 1 Slave queue ID: 0 /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 mode 6

  Read the article

• vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

  - by kce

  I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• How Hacker Can Access VPS CentOS 6 content?

  - by user2118559

  Just want to understand. Please, correct mistakes and write advices Hacker can access to VPS: 1. Through (using) console terminal, for example, using PuTTY. To access, hacker need to know port number, username and password. Port number hacker can know scanning open ports and try to login. The only way to login as I understand need to know username and password. To block (make more difficult) port scanning, need to use iptables configure /etc/sysconfig/iptables. I followed this https://www.digitalocean.com/community/articles/how-to-setup-a-basic-ip-tables-configuration-on-centos-6 tutorial and got *nat :PREROUTING ACCEPT [87:4524] :POSTROUTING ACCEPT [77:4713] :OUTPUT ACCEPT [77:4713] COMMIT *mangle :PREROUTING ACCEPT [2358:200388] :INPUT ACCEPT [2358:200388] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2638:477779] :POSTROUTING ACCEPT [2638:477779] COMMIT *filter :INPUT DROP [1:40] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [339:56132] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -p tcp -m tcp ! --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG FIN,SYN,RST,PSH,ACK,URG -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 110 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 21 -j ACCEPT COMMIT Regarding ports that need to be opened. If does not use ssl, then seems must leave open port 80 for website. Then for ssh (default 22) and for ftp (default 21). And set ip address, from which can connect. So if hacker uses other ip address, he can not access even knowing username and password? Regarding emails not sure. If I send email, using Gmail (Send mail as: (Use Gmail to send from your other email addresses)), then port 25 not necessary. For incoming emails at dynadot.com I use Email Forwarding. Does it mean that emails “does not arrive to VPS” (before arriving to VPS, emails are forwarded, for example to Gmail)? If emails does not arrive to VPS, then seems port 110 also not necessary. If use only ssl, must open port 443 and close port 80. Do not understand regarding port 3306 In PuTTY with /bin/netstat -lnp see Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 992/mysqld As understand it is for mysql. But does not remember that I have opened such port (may be when installed mysql, the port is opened automatically?). Mysql is installed on the same server, where all other content. Need to understand regarding port 3306 2. Also hacker may be able access console terminal through VPS hosting provider Control Panel (serial console emergency access). As understand only using console terminal (PuTTY, etc.) can make “global” changes (changes that can not modify with ftp). 3. Hacker can access to my VPS exploiting some hole in my php code and uploading, for example, Trojan. Unfortunately, faced situation that VPS was hacked. As understand it was because I used ZPanel. On VPS ( \etc\zpanel\panel\bin) ) found one php file, that was identified as Trojan by some virus scanners (at virustotal.com). Experimented with the file on local computer (wamp). And appears that hacker can see all content of VPS, rename, delete, upload etc. From my opinion, if in PuTTY use command like chattr +i /etc/php.ini then hacker could not be able to modify php.ini. Is there any other way to get into VPS?

  Read the article

• Transparent proxy which preserves client mac address

  - by A G

  I have a customer that wants to intercept SSL traffic as it leaves their network. My proposed solution is to setup a proxy that is transparent and both layer 2 and layer 3 so it can simply be dropped into their network without any change in config required. The proxy has two NICs, one connected to the server, the other to the client. The client, proxy and gateway are under control of the customer, the server is not. For example: client --- Proxy --- gateway -|- server I have my proxy program configured with IP_TRANSPARENT socket option to it can respond to connections destined for a remote IP. I am using the following setup: iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 3128 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1 ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 The client in question is on its own subnet and has been configured so that the proxy is the default gateway. The result is: Client sends a frame to the proxy; source IP is client, source mac is client, destination IP is server, destination mac is proxy Proxy forwards this frame to the gateway; source IP is proxy, source mac is proxy, destination IP is server, destination mac is gateway Gateway forwards this to the server and gets a response back. Gateway sends reply back to proxy; source IP is server, source mac is gateway, destination IP is proxy, destination mac is proxy Proxy forwards this reply to client; source IP is server, source mac is proxy, destination IP is client, destination mac is client. The tproxy and iptables configuration lets the proxy send packets with a non local ip address. Is there a way to make something transparent at the mac address level? That is, put the client on the same subnet as the gateway. The gateway sees the source IP and mac as that of the client, even though they originated from the proxy. Could this be done by configuring the proxy as a bridge then use ebtables to escalate the traffic to be handled by iptables? When I use ebtables to push something up to iptables, it appears my proxy program doesn't respond to the packets as they are destined for the gateways's mac address, not the proxy's. What are some other potential avenues I could investigate? EDIT: When the client and gateway are on different subnets (and client has set the proxy as the gateway), it works as described in 1 to 5. But I want to know if it is possible to have the client and gateway on the same subnet and have the proxy fully transparent (ie client is not aware of the proxy). Thanks! EDIT 2: I can configure the proxy as a bridge using brctl, but cannot find a way to direct this traffic to my proxy program - asked here Possible for linux bridge to intercept traffic?. Currently, with the description numbered 1 to 5, it operates at layer 3; it is transparent on the client side (client thinks it is talking to the server's IP), but not on the gateway side (gateway is talking to the proxy's IP). What I want to find out is, is it possible to make this operate at layer 2, so it is fully transparent? What are the available options I should research? Thanks

  Read the article

• An error occured synchronizing windows with time.windows.com

  - by Killrawr

  Okay so I've tried stopping/registering the win32tm service on this Windows Server 2008 Enterprise Computer. C:\Users\Administrator>net stop w32time The Windows Time service is stopping. The Windows Time service was stopped successfully. C:\Users\Administrator>w32tm /unregister The following error occurred: Access is denied. (0x80070005) C:\Users\Administrator>w32tm /unregister W32Time successfully unregistered. C:\Users\Administrator>w32tm /register W32Time successfully registered. C:\Users\Administrator>net start w32time The Windows Time service is starting. The Windows Time service was started successfully. (Source : http://social.technet.microsoft.com/Forums/en-US/winserverDS/thread/9bdfc2cc-4775-4435-8868-57d214e1e3ba/) And I get this error from the Date and Time, Internet Time tab (After also following the steps here). I've even tried the Atomic Time Clock Worldtimeserver and I get the error The following error occurred: The specified module could not be found. (0x8007007E). I've also disabled the Windows Firewall, that might of been blocking the synchronization. I've done a file scan with sfc /scannow that came back with no errors. C:\Users\Administrator>sfc /scannow Beginning system scan. This process will take some time. Beginning verification phase of system scan. Verification 100% complete. Windows Resource Protection did not find any integrity violations. C:\Users\Administrator> But I'm not having much luck. Is there anyway lo possibly solve this? or is the time.windows.com servers unsupported? because the software is from 2008? (I really don't know :/), My ping result to time.windows.com C:\Users\Administrator>ping time.windows.com Pinging time.microsoft.akadns.net [65.55.21.22] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 65.55.21.22: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), And tracert result C:\Users\Administratortracert time.windows.com Tracing route to time.microsoft.akadns.net [65.55.21.24] over a maximum of 30 hops: 1 1 ms <1 ms <1 ms 192.168.1.1 2 32 ms 31 ms 32 ms be2-100.bras1wtc.wlg.vf.net.nz [203.109.129.113] 3 31 ms 32 ms 31 ms be5-100.ppnzwtc01.wlg.vf.net.nz.129.109.203.in-a ddr.arpa [203.109.129.114] 4 31 ms 31 ms 31 ms gi0-2-0-3.ppnzwtc01.wlg.vf.net.nz.180.109.203.in -addr.arpa [203.109.180.210] 5 31 ms 31 ms 30 ms gi0-2-0-3.ppnzwtc02.wlg.vf.net.nz [203.109.180.2 09] 6 167 ms 166 ms 166 ms ip-141.199.31.114.VOCUS.net.au [114.31.199.141] 7 175 ms 175 ms 175 ms microsoft.com.any2ix.coresite.com [206.223.143.1 43] 8 177 ms 180 ms 176 ms xe-7-0-2-0.by2-96c-1a.ntwk.msn.net [207.46.42.17 6] 9 205 ms 205 ms 204 ms xe-10-0-2-0.co1-96c-1b.ntwk.msn.net [207.46.45.3 1] 10 * * * Request timed out. 11 * * * Request timed out. 12 * * * Request timed out. 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 ^C And nslookup C:\Users\Administrator>nslookup time.windows.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: time.microsoft.akadns.net Address: 65.55.21.22 Aliases: time.windows.com

  Read the article

• Can't connect to samba using openVPN

  - by Arthur

  I'm fairly new to using VPN. For a home project I'm running a OpenVPN server. This server runs within a network 192.168.2.0 and subnet 255.255.255.0 I can connect to this net work using the ip range 5.5.0.0 I guess the subnet is 255.255.255.192, but I'm not really sure about that. When connecting to my VPN network I can access the server via 5.5.0.1 and I can see the samba shares created on that machine. However I'm not allowed to connect to the samba share. When I look at the samba log of the computer which tries to connect I can see these messages: lib/access.c:338(allow_access) Denied connection from 5.5.0.132 (5.5.0.132) These are the share definition in /etc/samba/smb.conf interfaces = 192.168.2.0/32 5.5.0.0/24 security = user # wins-support = no # wins-server = w.x.y.z. // A LOT OF MORE SETTINGS AND COMMENTS hosts allow = 127.0.0.1 192.168.2.0/24 5.5.0.132/24 hosts deny = 0.0.0.0/0 browseable = yes path = [path to share] directory mask = 0755 force create mode = 0755 valid users = [a valid user, which i use to login with] writeable = yes force group = [the group i force to write with] force user = [the user i force to write with] This is the output of the ifconfig command as0t0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.1 P-t-P:5.5.0.1 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) as0t1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.65 P-t-P:5.5.0.65 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) as0t2 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.129 P-t-P:5.5.0.129 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:xxxx errors:0 dropped:0 overruns:0 frame:0 TX packets:xxxx errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:xxxx (xxxx MB) TX bytes:12403514 (xxxx MB) as0t3 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.193 P-t-P:5.5.0.193 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:7041 errors:0 dropped:0 overruns:0 frame:0 TX packets:9797 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:xxxx (xxxx KB) TX bytes:xxxx (xxxx MB) eth1 Link encap:Ethernet HWaddr 00:0e:2e:61:78:21 inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: xxxx:xxxx:xxxx:xxxx:7821/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:xxxx errors:0 dropped:0 overruns:0 frame:0 TX packets:xxxx errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:xxxx (xxxx MB) TX bytes:xxxx (xxxx MB) Interrupt:16 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:xxxx errors:0 dropped:0 overruns:0 frame:0 TX packets:xxxx errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:xxxx (xxxx MB) TX bytes:xxxx (xxxx MB) Can anyone tell me what is going wrong? My server is running Ubuntu 12.04 LTS

  Read the article

• Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

  - by Ritwik

  I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

  Read the article

• Router 2wire, Slackware desktop in DMZ mode, iptables policy aginst ping, but still pingable

  - by user135501

  I'm in DMZ mode, so I'm firewalling myself, stealthy all ok, but I get faulty test results from Shields Up that there are pings. Yesterday I couldn't make a connection to game servers work, because ping block was enabled (on the router). I disabled it, but this persists even due to my firewall. What is the connection between me and my router in DMZ mode (for my machine, there is bunch of others too behind router firewall)? When it allows router affecting if I'm pingable or not and if router has setting not blocking ping, rules in my iptables for this scenario do not work. Please ignore commented rules, I do uncomment them as I want. These two should do the job right? iptables -A INPUT -p icmp --icmp-type echo-request -j DROP echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all Here are my iptables: #!/bin/sh # Begin /bin/firewall-start # Insert connection-tracking modules (not needed if built into the kernel). #modprobe ip_tables #modprobe iptable_filter #modprobe ip_conntrack #modprobe ip_conntrack_ftp #modprobe ipt_state #modprobe ipt_LOG # allow local-only connections iptables -A INPUT -i lo -j ACCEPT # free output on any interface to any ip for any service # (equal to -P ACCEPT) iptables -A OUTPUT -j ACCEPT # permit answers on already established connections # and permit new connections related to established ones (eg active-ftp) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT #Gamespy&NWN #iptables -A INPUT -p tcp -m tcp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 6667 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 28910 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29900 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29901 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p tcp -m tcp --dport 29920 --tcp-flags SYN,RST,ACK SYN -j ACCEPT #iptables -A INPUT -p udp -m udp -m multiport --ports 5120:5129 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 6500 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27900 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 27901 -j ACCEPT #iptables -A INPUT -p udp -m udp --dport 29910 -j ACCEPT # Log everything else: What's Windows' latest exploitable vulnerability? iptables -A INPUT -j LOG --log-prefix "FIREWALL:INPUT" # set a sane policy: everything not accepted > /dev/null iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP iptables -A INPUT -p icmp --icmp-type echo-request -j DROP # be verbose on dynamic ip-addresses (not needed in case of static IP) echo 2 > /proc/sys/net/ipv4/ip_dynaddr # disable ExplicitCongestionNotification - too many routers are still # ignorant echo 0 > /proc/sys/net/ipv4/tcp_ecn #ping death echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_all # If you are frequently accessing ftp-servers or enjoy chatting you might # notice certain delays because some implementations of these daemons have # the feature of querying an identd on your box for your username for # logging. Although there's really no harm in this, having an identd # running is not recommended because some implementations are known to be # vulnerable. # To avoid these delays you could reject the requests with a 'tcp-reset': #iptables -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset #iptables -A OUTPUT -p tcp --sport 113 -m state --state RELATED -j ACCEPT # To log and drop invalid packets, mostly harmless packets that came in # after netfilter's timeout, sometimes scans: #iptables -I INPUT 1 -p tcp -m state --state INVALID -j LOG --log-prefix \ "FIREWALL:INVALID" #iptables -I INPUT 2 -p tcp -m state --state INVALID -j DROP # End /bin/firewall-start

  Read the article

• vagrant fails to bring up additional adapter for centos vm using virtual box provider

  - by Anadi Misra

  this is in continuation of the question asked here about host only adapter on dhcp I upgraded to vagrant 1.6.3 and the updated Vagrantfile to following setting for multiple adapters # add additional adapter for inter machine networking dev.vm.network :private_network, :type => "dhcp", :adapter => "2", :netmask => "255.255.255.0" it goes through creating adapters but then fails bringing up the mic on vm Anadis-MacBook-Pro:full-stack-env anadi$ vagrant up Bringing machine 'full-stack-env' up with 'virtualbox' provider... ==> full-stack-env: Clearing any previously set forwarded ports... ==> full-stack-env: Clearing any previously set network interfaces... ==> full-stack-env: Preparing network interfaces based on configuration... full-stack-env: Adapter 1: nat full-stack-env: Adapter 2: hostonly ==> full-stack-env: Forwarding ports... full-stack-env: 22 => 4223 (adapter 1) full-stack-env: 8080 => 8090 (adapter 1) ==> full-stack-env: Running 'pre-boot' VM customizations... ==> full-stack-env: Booting VM... ==> full-stack-env: Waiting for machine to boot. This may take a few minutes... full-stack-env: SSH address: 127.0.0.1:4223 full-stack-env: SSH username: vagrant full-stack-env: SSH auth method: private key full-stack-env: Warning: Connection timeout. Retrying... full-stack-env: Warning: Connection timeout. Retrying... full-stack-env: Warning: Remote connection disconnect. Retrying... ==> full-stack-env: Machine booted and ready! ==> full-stack-env: Checking for guest additions in VM... ==> full-stack-env: Setting hostname... ==> full-stack-env: Configuring and enabling network interfaces... The following SSH command responded with a non-zero exit status. Vagrant assumes that this means the command failed! ARPCHECK=no /sbin/ifup eth 2> /dev/null Stdout from the command: Device eth does not seem to be present, delaying initialization. Stderr from the command: how ever when I log in to the environment I see two network interfaces as expected Anadis-MacBook-Pro:full-stack-env anadi$ vagrant ssh Last login: Wed Jun 4 12:54:47 2014 from 10.0.2.2 [vagrant@full-stack-env ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:BD:39:57 inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:febd:3957/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:511 errors:0 dropped:0 overruns:0 frame:0 TX packets:360 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54574 (53.2 KiB) TX bytes:46675 (45.5 KiB) eth1 Link encap:Ethernet HWaddr 08:00:27:A3:86:C9 inet addr:172.28.128.3 Bcast:172.28.128.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:86c9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1360 (1.3 KiB) TX bytes:894 (894.0 b) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) I am bit confused here on why it is trying to add another mic (eth2)? In the VM I used for creating this vagrant box, I had added two NICs already.

  Read the article

• iptables rule(s) to send openvpn traffic from clients over an sshuttle tunnel?

  - by Sam Martin

  I have an Ubuntu 12.04 box with OpenVPN. The VPN is working as expected -- clients can connect, browse the Web, etc. The OpenVPN server IP is 10.8.0.1 on tun0. On that same box, I can use sshuttle to tunnel into another network to access a Web server on 10.10.0.9. sshuttle does its magic using the following iptables commands: iptables -t nat -N sshuttle-12300 iptables -t nat -F sshuttle-12300 iptables -t nat -I OUTPUT 1 -j sshuttle-12300 iptables -t nat -I PREROUTING 1 -j sshuttle-12300 iptables -t nat -A sshuttle-12300 -j REDIRECT --dest 10.10.0.0/24 -p tcp --to-ports 12300 -m ttl ! --ttl 42 iptables -t nat -A sshuttle-12300 -j RETURN --dest 127.0.0.0/8 -p tcp Is it possible to forward traffic from OpenVPN clients over the sshuttle tunnel to the remote Web server? I'd ultimately like to be able to set up any complicated tunneling on the server, and have relatively "dumb" clients (iPad, etc.) be able to access the remote servers via OpenVPN. Below is a basic diagram of the scenario: [Edit: added output from the OpenVPN box] $ sudo iptables -nL -v -t nat Chain PREROUTING (policy ACCEPT 1498 packets, 252K bytes) pkts bytes target prot opt in out source destination 1512 253K sshuttle-12300 all -- * * 0.0.0.0/0 0.0.0.0/0 Chain INPUT (policy ACCEPT 322 packets, 58984 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 584 packets, 43241 bytes) pkts bytes target prot opt in out source destination 587 43421 sshuttle-12300 all -- * * 0.0.0.0/0 0.0.0.0/0 Chain POSTROUTING (policy ACCEPT 589 packets, 43595 bytes) pkts bytes target prot opt in out source destination 1175 76298 MASQUERADE all -- * eth0 10.8.0.0/24 0.0.0.0/0 Chain sshuttle-12300 (2 references) pkts bytes target prot opt in out source destination 17 1076 REDIRECT tcp -- * * 0.0.0.0/0 10.10.0.0/24 TTL match TTL != 42 redir ports 12300 0 0 RETURN tcp -- * * 0.0.0.0/0 127.0.0.0/8 $ sudo iptables -nL -v -t filter Chain INPUT (policy ACCEPT 97493 packets, 30M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 131K 109M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 1370 89160 ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable [Edit 2: more OpenVPN server output] $ netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 [Edit 3: still more debug output] IP forwarding appears to be enabled correctly on the OpenVPN server: # find /proc/sys/net/ipv4/conf/ -name forwarding -ls -execdir cat {} \; 18926 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/all/forwarding 1 18954 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/default/forwarding 1 18978 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/eth0/forwarding 1 19003 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/lo/forwarding 1 19028 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/tun0/forwarding 1 Client routing table: $ netstat -r Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 8 48 tun0 default 192.168.1.1 UGSc 2 1652 en1 10.8.0.1/32 10.8.0.5 UGSc 1 0 tun0 10.8.0.5 10.8.0.6 UHr 13 0 tun0 10.10.0/24 10.8.0.5 UGSc 0 0 tun0 <snip> Traceroute from client: $ traceroute 10.10.0.9 traceroute to 10.10.0.9 (10.10.0.9), 64 hops max, 52 byte packets 1 10.8.0.1 (10.8.0.1) 5.403 ms 1.173 ms 1.086 ms 2 192.168.1.1 (192.168.1.1) 4.693 ms 2.110 ms 1.990 ms 3 l100.my-verizon-garbage (client-ext-ip) 7.453 ms 7.089 ms 6.248 ms 4 * * * 5 10.10.0.9 (10.10.0.9) 14.915 ms !N * 6.620 ms !N

  Read the article

• iptables 1.4 and passive FTP on custom port

  - by Cracky

  after the upgrade from debian squeeze to wheezy I've got a problem with passive FTP connection. I could narrow it to be iptables related, as I could connect via FTP w/o problems after adding my IP to the iptables ACCEPT rule. Before the upgrade I was able just to do modprobe nf_conntract_ftp ports=21332 and adding iptables -A THRU -p tcp --dport 21332 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT now..it doesn't help anymore. The INPUT rule is being triggered as I can see in the counter, but the directory listing is the last thing it does. Setting up a passive-port range is the last thing I want to do, I dislike open ports. I also tried the trick with helper mod by adding following rule before the actual rule for 21332 iptables -A THRU -p tcp -i eth0 --dport 21332 -m state --state NEW -m helper --helper ftp-21332 -j ACCEPT but it doesn't help and is even not being triggered according to counter. The rule in the next line (w/o helper) is being triggered.. here some info: # iptables --version iptables v1.4.14 # lsmod |grep nf_ nf_nat_ftp 12460 0 nf_nat 18242 1 nf_nat_ftp nf_conntrack_ftp 12605 1 nf_nat_ftp nf_conntrack_ipv4 14078 32 nf_nat nf_defrag_ipv4 12483 1 nf_conntrack_ipv4 nf_conntrack 52720 7 xt_state,nf_conntrack_ipv4,xt_conntrack,nf_conntrack_ftp,nf_nat,nf_nat_ftp,xt_helper # uname -a Linux loki 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux # iptables-save # Generated by iptables-save v1.4.14 on Sun Jun 30 03:54:28 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :BLACKLIST - [0:0] :LOGDROP - [0:0] :SPAM - [0:0] :THRU - [0:0] :WEB - [0:0] :fail2ban-dovecot-pop3imap - [0:0] :fail2ban-pureftpd - [0:0] :fail2ban-ssh - [0:0] -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -p tcp -m multiport --dports 21,21332 -j fail2ban-pureftpd -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN FIN,SYN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,ACK FIN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags ACK,URG URG -j DROP -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -j BLACKLIST -A INPUT -j THRU -A INPUT -j LOGDROP -A OUTPUT -j ACCEPT -A OUTPUT -s 93.223.38.223/32 -j ACCEPT -A BLACKLIST -s 38.113.165.0/24 -j LOGDROP -A BLACKLIST -s 202.177.216.0/24 -j LOGDROP -A BLACKLIST -s 130.117.190.0/24 -j LOGDROP -A BLACKLIST -s 117.79.92.0/24 -j LOGDROP -A BLACKLIST -s 72.47.228.0/24 -j LOGDROP -A BLACKLIST -s 195.200.70.0/24 -j LOGDROP -A BLACKLIST -s 195.200.71.0/24 -j LOGDROP -A LOGDROP -m limit --limit 5/sec -j LOG --log-prefix drop_packet_ --log-level 7 -A LOGDROP -p tcp -m tcp --dport 25 -m limit --limit 2/sec -j LOG --log-prefix spam_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 80 -m limit --limit 2/sec -j LOG --log-prefix web_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 22 -m limit --limit 2/sec -j LOG --log-prefix ssh_blacklist --log-level 7 -A LOGDROP -j REJECT --reject-with icmp-host-prohibited -A THRU -p icmp -m limit --limit 1/sec -m icmp --icmp-type 8 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 25 -j ACCEPT -A THRU -i eth0 -p udp -m udp --dport 53 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 110 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 143 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 465 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 585 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 993 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 995 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 2008 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 10011 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 21332 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 30033 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-ssh -j RETURN -A fail2ban-ssh -j RETURN COMMIT # Completed on Sun Jun 30 03:54:28 2013 So, as I said, I have no problems with connecting when adding my IP to go through..but that's not a solution as noone except me can connect anymore~ If someone got an idea what the problem is, please help me! Thanks Cracky

  Read the article

• Set source address to use tun device does not work (Debian Squeeze)

  - by A. Donda

  there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

  Read the article

• Can't get FTP to work on centOS 5.6

  - by josi

  Hi guys I have been trying for a few hours to install and get FTP to work... I did yum install ftp and yum install vsftpd They all installed and are running but when I try to use filezilla or some other client I just can't connect....I've tried connecting on port 21 and port 990 ....nothing! These are my iptables # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p esp -j ACCEPT -A RH-Firewall-1-INPUT -p ah -j ACCEPT -A RH-Firewall-1-INPUT -d 224.0.0.251 -p udp -m udp --dport 5353 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 53 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 110 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 990 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 465 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 646 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 993 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 995 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10009 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 7778 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5000 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25566 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8765 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8192 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8123 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 20 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m state --state NEW -m udp --dport 23877 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 9091 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 51413 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10011 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 30033 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT Any help would be much appreciated! If I do lsof -i :21 without the "." it shows nothing. [root@ks3000420 ~]# lsof -i :21 . COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME bash 9964 root cwd DIR 8,1 4096 483329 . bash 11608 root cwd DIR 8,1 4096 483329 . bash 13550 root cwd DIR 8,1 4096 483329 . vi 14117 root cwd DIR 8,1 4096 483329 . sftp-serv 15261 root cwd DIR 8,1 4096 483329 . sftp-serv 15477 root cwd DIR 8,1 4096 483329 . bash 19074 root cwd DIR 8,1 4096 483329 . lsof 19100 root cwd DIR 8,1 4096 483329 . lsof 19101 root cwd DIR 8,1 4096 483329 .

  Read the article

• OpenVPN on Ubuntu 11.10 - unable to redirect default gateway

  - by Vladimir Kadalashvili

  I'm trying to connect to connect to OpenVPN server from my Ubuntu 11.10 machine. I use the following command to do it (under root user): openvpn --config /home/vladimir/client.ovpn Everything seems to be OK, it connects normally without any warnings and errors, but when I try to browse the internet I see that I still use my own IP address, so VPN connection doesn't work. When I run openvpn command, it displays the following message among others: NOTE: unable to redirect default gateway -- Cannot read current default gateway from system I think it's the cause of this problem, but unfortunately I don't know how to fix it. Below is full output of openvpn command: Sat Jun 9 23:51:36 2012 OpenVPN 2.2.0 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jul 4 2011 Sat Jun 9 23:51:36 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sat Jun 9 23:51:36 2012 Control Channel Authentication: tls-auth using INLINE static key file Sat Jun 9 23:51:36 2012 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:36 2012 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:36 2012 LZO compression initialized Sat Jun 9 23:51:36 2012 Control Channel MTU parms [ L:1542 D:166 EF:66 EB:0 ET:0 EL:0 ] Sat Jun 9 23:51:36 2012 Socket Buffers: R=[126976->200000] S=[126976->200000] Sat Jun 9 23:51:36 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sat Jun 9 23:51:36 2012 Local Options hash (VER=V4): '504e774e' Sat Jun 9 23:51:36 2012 Expected Remote Options hash (VER=V4): '14168603' Sat Jun 9 23:51:36 2012 UDPv4 link local: [undef] Sat Jun 9 23:51:36 2012 UDPv4 link remote: [AF_INET]94.229.78.130:1194 Sat Jun 9 23:51:37 2012 TLS: Initial packet from [AF_INET]94.229.78.130:1194, sid=13fd921b b42072ab Sat Jun 9 23:51:37 2012 VERIFY OK: depth=1, /CN=OpenVPN_CA Sat Jun 9 23:51:37 2012 VERIFY OK: nsCertType=SERVER Sat Jun 9 23:51:37 2012 VERIFY OK: depth=0, /CN=OpenVPN_Server Sat Jun 9 23:51:38 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sat Jun 9 23:51:38 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:38 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sat Jun 9 23:51:38 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:38 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sat Jun 9 23:51:38 2012 [OpenVPN_Server] Peer Connection Initiated with [AF_INET]94.229.78.130:1194 Sat Jun 9 23:51:40 2012 SENT CONTROL [OpenVPN_Server]: 'PUSH_REQUEST' (status=1) Sat Jun 9 23:51:40 2012 PUSH: Received control message: 'PUSH_REPLY,explicit-exit-notify,topology subnet,route-delay 5 30,dhcp-pre-release,dhcp-renew,dhcp-release,route-metric 101,ping 5,ping-restart 40,redirect-gateway def1,redirect-gateway bypass-dhcp,redirect-gateway autolocal,route-gateway 5.5.0.1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.4.4,register-dns,comp-lzo yes,ifconfig 5.5.117.43 255.255.0.0' Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:4: dhcp-pre-release (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:5: dhcp-renew (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:6: dhcp-release (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:16: register-dns (2.2.0) Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: timers and/or timeouts modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: explicit notify parm(s) modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: LZO parms modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: --ifconfig/up options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: route options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: route-related options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sat Jun 9 23:51:40 2012 ROUTE: default_gateway=UNDEF Sat Jun 9 23:51:40 2012 TUN/TAP device tun0 opened Sat Jun 9 23:51:40 2012 TUN/TAP TX queue length set to 100 Sat Jun 9 23:51:40 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Sat Jun 9 23:51:40 2012 /sbin/ifconfig tun0 5.5.117.43 netmask 255.255.0.0 mtu 1500 broadcast 5.5.255.255 Sat Jun 9 23:51:45 2012 NOTE: unable to redirect default gateway -- Cannot read current default gateway from system Sat Jun 9 23:51:45 2012 Initialization Sequence Completed Output of route command: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default * 0.0.0.0 U 0 0 0 ppp0 5.5.0.0 * 255.255.0.0 U 0 0 0 tun0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.0.0 * 255.255.255.0 U 0 0 0 wlan0 stream-ts1.net. * 255.255.255.255 UH 0 0 0 ppp0 Output of ifconfig command: eth0 Link encap:Ethernet HWaddr 6c:62:6d:44:0d:12 inet6 addr: fe80::6e62:6dff:fe44:d12/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54594 errors:0 dropped:0 overruns:0 frame:0 TX packets:59897 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44922107 (44.9 MB) TX bytes:8839969 (8.8 MB) Interrupt:41 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4561 errors:0 dropped:0 overruns:0 frame:0 TX packets:4561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:685425 (685.4 KB) TX bytes:685425 (685.4 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:213.206.63.44 P-t-P:213.206.34.4 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:53577 errors:0 dropped:0 overruns:0 frame:0 TX packets:58892 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:43667387 (43.6 MB) TX bytes:7504776 (7.5 MB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.117.43 P-t-P:5.5.117.43 Mask:255.255.0.0 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:27:19:f6:b5:cf inet addr:192.168.0.1 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::227:19ff:fef6:b5cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12079 errors:0 dropped:0 overruns:0 frame:0 TX packets:11178 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1483691 (1.4 MB) TX bytes:4307899 (4.3 MB) So my question is - how to make OpenVPN redirect default gateway? Thanks!

  Read the article

• CD/DVD burn error in ImgBurn and Nero

  - by bobby

  I am getting the errors shown below when I try to burn a CD/DVD on my DVD writer. I am seeing this error for every CD/DVD I try to burn. I am not able to write any CDs or DVDs using ImgBurn. The burn log below is a failed burn in Nero. What could be causing this error? Nero Burning ROM bobby 4C85-200E-4005-0004-0000-7660-0800-35X3-0000-407M-MX37-**** (*) Windows XP 6.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.11.3. Internal Version: 7, 11, 3, (Nero Express) Recorder: <HL-DT-ST DVDRAM GSA-H12N> Version: UL01 - HA 1 TA 1 - 7.11.3.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: <ATAPI-CD ROM-DRIVE-52MAX > Version: 52PP - HA 1 TA 0 - 7.11.3.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === === CDRom-Device-Map === ATAPI-CD ROM-DRIVE-52MAX F: CdRom0 HL-DT-ST DVDRAM GSA-H12N G: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981560kB) Free physical memory: 309MB (317024kB) Memory in use : 67 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 11.6.2010 CD Image 10:43:02 AM #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 10:43:02 AM #2 Text 0 File Burncd.cpp, Line 3186 HL-DT-ST DVDRAM GSA-H12N Buffer underrun protection activated 10:43:02 AM #3 Text 0 File Burncd.cpp, Line 3500 Turn on Disc-At-Once, using CD-R/RW media 10:43:02 AM #4 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 359848 ( 79:59.73) Last address to be written: 318783 ( 70:52.33) 10:43:02 AM #5 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 10:43:02 AM #6 Text 0 File DlgWaitCD.cpp, Line 2988 Recorder: HL-DT-ST DVDRAM G SA-H12N; CDR co de: 00 97 27 18; O SJ entry from: Pla smon Data systems Ltd. ATIP Data: Special Info [hex] 1: D0 00 A0, 2: 61 1B 12 (LI 97:27.18), 3: 4F 3B 4A ( LO 79:59.74) Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 0 0 00 (invalid) 10:43:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 10:43:02 AM #8 Text 0 File ThreadedTransferInterface.cpp, Line 785 Nero Report 1 Nero Burning ROM Setup items (after recorder preparation) 0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, Joliet) 2 indices, index0 (150) not provided original disc pos #0 + 318784 (318784) = #318784/70:50.34 not relocatable, disc pos for caching/writing not required/not required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318784 blocks [G: HL-DT-ST DVDRAM GSA-H12N] -------------------------------------------------------------- 10:43:02 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [G: HL-DT-ST DVDRAM GSA-H12N] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Se ssion Clo sed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next T rk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 6531768 32, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ -150 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 -150 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 318784 | 318784 | 0x00 318784 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 10:43:02 AM #10 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 10:43:02 AM #11 Text 0 File Burncd.cpp, Line 4286 Caching options: cache CDRom or Network-Yes, small files-Yes (<64KB) 10:43:02 AM #12 Phase 24 File dlgbrnst.cpp, Line 1767 Caching of files started 10:43:02 AM #13 Text 0 File Burncd.cpp, Line 4405 Cache writing successful. 10:43:02 AM #14 Phase 25 File dlgbrnst.cpp, Line 1767 Caching of files completed 10:43:02 AM #15 Phase 36 File dlgbrnst.cpp, Line 1767 Burn process started at 48x (7,200 KB/s) 10:43:02 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2733 Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0 10:43:02 AM #17 Text 0 File MMC.cpp, Line 17806 StartDAO : CD-Text - Off 10:43:02 AM #18 Text 0 File MMC.cpp, Line 22488 Set BUFE: Buffer underrun protection -> ON 10:43:03 AM #19 Text 0 File MMC.cpp, Line 18034 CueData, Len=32 41 00 00 14 00 00 00 00 41 01 00 10 00 00 00 00 41 01 01 10 00 00 02 00 41 aa 01 14 00 46 34 22 10:43:03 AM #20 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 10:43:16 AM #21 Text 0 File Cdrdrv.cpp, Line 1405 10:43:16.806 - G: HL-DT-ST DVDRAM GSA-H12N : Queue again later 10:43:42 AM #22 SPTI -1502 File SCSIPassThrough.cpp, Line 181 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1502) Sense Key: 0x04 (KEY_HARDWARE_ERROR) Nero Report 2 Nero Burning ROM Sense Code: 0x08 Sense Qual: 0x03 CDB Data: 0x2A 00 00 00 4D 00 00 00 20 00 00 00 Sense Area: 0x70 00 04 00 00 00 00 10 53 29 A1 80 08 03 Buffer x0c7d9a40: Len x10000 0xDC 87 EB 41 6E AC 61 5A 07 B2 DB 78 B5 D4 D9 24 0x8D BC 51 38 46 56 0F EE 16 15 5C 5B E3 B0 10 16 0x14 B1 C3 6E 30 2B C4 78 15 AB D5 92 09 B7 81 23 10:43:42 AM #23 CDR -1502 File Writer.cpp, Line 306 DMA-driver error, CRC error G: HL-DT-ST DVDRAM GSA-H12N 10:43:55 AM #24 Phase 38 File dlgbrnst.cpp, Line 1767 Burn process failed at 48x (7,200 KB/s) 10:43:55 AM #25 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 10:44:01 AM #26 Text 0 File Cdrdrv.cpp, Line 11412 DriveLocker: UnLockVolume completed 10:44:01 AM #27 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon Nero Report 3

  Read the article

• Ports do not open after rules appended in iptables

  - by user2699451

  I have a server that I am trying to setup for OpenVPN. I have followed all the steps, but I see that when I try to connect to it in Windows, it doesn't allow me, it just hangs on connecting, so I did a nmap scan and I see that port 1194 is not open so naturally I append the rule to open 1194 with: iptables -A INPUT -i eth0 -p tcp --dport 1194 -j ACCEPT followed by service iptables save and service iptables restart which all executed successfully. Then I try again, but it doesn't work and another nmap scan says that port 1194 is closed. Here is the iptables configuration: # Generated by iptables-save v1.4.7 on Thu Oct 31 09:47:38 2013 *nat :PREROUTING ACCEPT [27410:3091993] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [5042:376160] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -j SNAT --to-source 41.185.26.238 -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 31 09:47:38 2013 # Generated by iptables-save v1.4.7 on Thu Oct 31 09:47:38 2013 *filter :INPUT ACCEPT [23571:2869068] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [27558:3656524] :vl - [0:0] -A INPUT -p tcp -m tcp --dport 5252 -m comment --comment "SSH Secure" -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -m state --state NEW,RELATED,ESTABLISHED -$ -A INPUT -i lo -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -m comment --comment "SSH" -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -m comment --comment "HTTP" -j ACCEPT -A INPUT -p tcp -m tcp --dport 8080 -m comment --comment "HTTPS" -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -m comment --comment "HTTP Encrypted" -j ACCEP$ -A INPUT -i eth0 -p tcp -m tcp --dport 1723 -j ACCEPT -A INPUT -i eth0 -p gre -j ACCEPT -A INPUT -p udp -m udp --dport 1194 -j ACCEPT -A FORWARD -i ppp+ -o eth0 -j ACCEPT -A FORWARD -i eth0 -o ppp+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 10.8.0.0/24 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -p icmp -m icmp --icmp-type 0 -m state --state RELATED,ESTABLISHED -j A$ COMMIT # Completed on Thu Oct 31 09:47:38 2013 and my nmap scan from: localhost: nmap localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 09:53 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000011s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 443/tcp open https 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.06 seconds remote pc: nmap [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 09:53 SAST Nmap scan report for rla04-nix1.wadns.net (41.185.26.238) Host is up (0.025s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 15.70 seconds So, I do not know what is causing this, any assistance will be appreciated! UPDATE AFTER FIRST ANSWER::: [root@RLA04-NIX1 ~]# iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT [root@RLA04-NIX1 ~]# iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT [root@RLA04-NIX1 ~]# iptables -A FORWARD -j REJECT [root@RLA04-NIX1 ~]# iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE [root@RLA04-NIX1 ~]# service iptables save iptables: Saving firewall rules to /etc/sysconfig/iptables:[ OK ] [root@RLA04-NIX1 ~]# service iptables restart iptables: Flushing firewall rules: [ OK ] iptables: Setting chains to policy ACCEPT: filter nat [ OK ] iptables: Unloading modules: [ OK ] iptables: Applying firewall rules: [ OK ] [root@RLA04-NIX1 ~]# lsof -i :1194 -bash: lsof: command not found iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:5252 /* SSH Secure */ ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 state NEW,RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 /* SSH */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 /* HTTP */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:8080 /* HTTPS */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 /* HTTP Encrypted */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:1723 ACCEPT 47 -- 0.0.0.0/0 0.0.0.0/0 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 0.0.0.0/0 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 0.0.0.0/0 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0 state RELATED,ESTABLISHED Chain vl (0 references) target prot opt source destination [root@RLA04-NIX1 ~]# nmap localhostt Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 11:13 SAST remote pc nmap [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 11:11 SAST Nmap scan report for rla04-nix1.wadns.net (41.185.26.238) Host is up (0.020s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 4.18 seconds localhost nmap localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 11:13 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000011s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 443/tcp open https 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.06 seconds UPDATE AFTER SCANNING UDP PORTS Sorry, I am noob, I am still learning, but here is the output for: nmap -sU [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 11:33 SAST Nmap scan report for [server address] ([server ip]) Host is up (0.021s latency). Not shown: 997 open|filtered ports PORT STATE SERVICE 53/udp closed domain 123/udp closed ntp 33459/udp closed unknown Nmap done: 1 IP address (1 host up) scanned in 8.57 seconds btw, no changes have been made since post started (except for iptables changes)

  Read the article

• How to use CLEAR USB internet connection in Ubuntu (host) and WindowsXP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for linux as yet. I've installed windowsxp as guest in ubuntu and the version I'm using is 3.2.2. USB is connecting fine in WindowsXP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• MySQL port 3306 blocked in csf yet can still telnet to port 3306 from external host

  - by Neek

  We have a Centos 6 VPS that was recently migrated to a new machine within the same web hosting company. It's running WHM/cPanel and has csf/lfd installed. csf is set up with mostly vanilla config. I'm no iptables expert, csf has not let me down before. If a port isn't in the TCP_IN list, it should be blocked on the firewall by iptables. My problem is that I can telnet to port 3306 from an external host, yet I think iptables ought to be blocking 3306 because of csf's rules. We are now failing a security check because of this open port. (this output is obfuscated to protect the innocent: www.ourhost.com is the host with the firewall problem) [root@nickfenwick log]# telnet www.ourhost.com 3306 Trying 158.255.45.107... Connected to www.ourhost.com. Escape character is '^]'. HHost 'nickfenwick.com' is not allowed to connect to this MySQL serverConnection closed by foreign host. So the connection is established, and MySQL refuses the connection due to its configuration. I need the network connection to be refused at the firewall level, before it reaches MySQL. Using WHM's csf web UI I can see 'Firewall Configuration' includes a fairly sensible TCP_IN line: TCP_IN: 20,21,22,25,53,80,110,143,222,443,465,587,993,995,2077,2078,2082,2083,2086,2087,2095,2096,8080 (lets ignore that I could trim that a little for now, my concern is that 3306 is not listed in that list) When csf is restarted it logs the usual slew of output as it sets up iptables rules, for example what looks like it blocking all traffic and then allowing specific ports like SSH on 22: [cut] DROP all opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 [cut] ACCEPT tcp opt -- in !lo out * 0.0.0.0/0 -> 0.0.0.0/0 state NEW tcp dpt:22 [cut] I can see that iptables is running, service iptables status returns a long list of firewall rules. Here is my Chain INPUT section from service iptables status, hopefully that's enough to show how the firewall is configured. Table: filter Chain INPUT (policy DROP) num target prot opt source destination 1 acctboth all -- 0.0.0.0/0 0.0.0.0/0 2 ACCEPT tcp -- 217.112.88.10 0.0.0.0/0 tcp dpt:53 3 ACCEPT udp -- 217.112.88.10 0.0.0.0/0 udp dpt:53 4 ACCEPT tcp -- 217.112.88.10 0.0.0.0/0 tcp spt:53 5 ACCEPT udp -- 217.112.88.10 0.0.0.0/0 udp spt:53 6 ACCEPT tcp -- 8.8.4.4 0.0.0.0/0 tcp dpt:53 7 ACCEPT udp -- 8.8.4.4 0.0.0.0/0 udp dpt:53 8 ACCEPT tcp -- 8.8.4.4 0.0.0.0/0 tcp spt:53 9 ACCEPT udp -- 8.8.4.4 0.0.0.0/0 udp spt:53 10 ACCEPT tcp -- 8.8.8.8 0.0.0.0/0 tcp dpt:53 11 ACCEPT udp -- 8.8.8.8 0.0.0.0/0 udp dpt:53 12 ACCEPT tcp -- 8.8.8.8 0.0.0.0/0 tcp spt:53 13 ACCEPT udp -- 8.8.8.8 0.0.0.0/0 udp spt:53 14 LOCALINPUT all -- 0.0.0.0/0 0.0.0.0/0 15 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 16 INVALID tcp -- 0.0.0.0/0 0.0.0.0/0 17 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 18 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:20 19 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:21 20 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 21 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:25 22 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:53 23 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 24 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:110 25 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:143 26 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:222 27 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:443 28 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:465 29 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:587 30 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:993 31 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:995 32 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2077 33 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2078 34 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2082 35 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2083 36 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2086 37 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2087 38 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2095 39 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2096 40 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:8080 41 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:20 42 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:21 43 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:53 44 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:222 45 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:8080 46 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 47 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0 48 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 49 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 50 LOGDROPIN all -- 0.0.0.0/0 0.0.0.0/0 What's the next thing to check?

  Read the article

• OpenVPN Server Ethernet Bridging Question

  - by Hooplad

  Hello All, I am having a difficult time properly configuring an ethernet bridge using OpenVPN 2.0.9 install on CentOS 5 ( VPN server ). The goal that I am trying to complete is to connect a VM ( instance running on the same CentOS machine ) acting as a Microsoft Business Contact Manager server. I would then like this "BCM server" to serve Windows XP clients on 192.168.1.0/24 network as well as clients connecting from VPN ( 10.8.0.0/24 ). The setup as it is now was based off a known working configuration. The problem with the working configuration was that it would allow to the client to connect and access everything running on the VPN server ( SVN, Samba, VM Server ) but not any computers on the 192.168.1.0/24 network. I must disclose that the VPN server is behind a router/firewall. Ports are being forwarded correctly ( again, clients were able to connect to the VPN server with no problem. netcat confirms the udp port is open as well ). current ifconfig output br0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 inet addr:192.168.1.169 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:5eff:fe4d:3ac2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:846890 errors:0 dropped:0 overruns:0 frame:0 TX packets:3072351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42686842 (40.7 MiB) TX bytes:4540654180 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:882641 errors:0 dropped:0 overruns:0 frame:0 TX packets:1781383 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:82342803 (78.5 MiB) TX bytes:2614727660 (2.4 GiB) Interrupt:169 eth1 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:650 errors:0 dropped:0 overruns:0 frame:0 TX packets:1347223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67403 (65.8 KiB) TX bytes:1959529142 (1.8 GiB) Interrupt:233 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:17452058 errors:0 dropped:0 overruns:0 frame:0 TX packets:17452058 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94020256229 (87.5 GiB) TX bytes:94020256229 (87.5 GiB) tap0 Link encap:Ethernet HWaddr DE:18:C6:D7:01:63 inet6 addr: fe80::dc18:c6ff:fed7:163/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3086 errors:0 dropped:166 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:315099 (307.7 KiB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:192.168.177.1 Bcast:192.168.177.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:192.168.55.1 Bcast:192.168.55.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) current route table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.55.0 * 255.255.255.0 U 0 0 0 vmnet8 192.168.177.0 * 255.255.255.0 U 0 0 0 vmnet1 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 current iptables output Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination server_known_working.conf local banshee port 1194 proto udp dev tap0 ca ca.crt cert banshee_server.crt key banshee_server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 192.168.1.0 255.255.255.0" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 4 The following is the current CentOS server config file. server_ethernet_bridged.conf ( current ) local 192.168.1.169 port 1194 proto udp dev tap0 ca ca.crt cert server.crt key server.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.1.169 255.255.255.0 192.168.1.200 192.168.1.210 push "route 192.168.1.0 255.255.255.0 192.168.1.1" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 6 The following is one of the client's config file that was used with the known working configuration. client.opvn client dev tap proto udp remote XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca client.crt cert client.crt key client.key tls-auth client.key 1 verb 3 I have tried the HOWTO provided by OpenVPN as well as others http://www.thebakershome.net/openvpn%5Ftutorial?page=1 with no success. Any help or suggestions would be appreciated.

  Read the article

• SVN Server not responding

  - by Rob Forrest

  I've been bashing my head against a wall with this one all day and I would greatly appreciate a few more eyes on the problem at hand. We have an in-house SVN Server that contains all live and development code for our website. Our live server can connect to this and get updates from the repository. This was all working fine until we migrated the SVN Server from a physical machine to a vSphere VM. Now, for some reason that continues to fathom me, we can no longer connect to the SVN Server. The SVN Server runs CentOS 6.2, Apache and SVN 1.7.2. SELinux is well and trully disabled and the problem remains when iptables is stopped. Our production server does run an older version of CentOS and SVN but the same system worked previously so I don't think that this is the issue. Of note, if I have iptables enabled, using service iptables status, I can see a single packet coming in and being accepted but the production server simply hangs on any svn command. If I give up waiting and do a CTRL-C to break the process I get a "could not connect to server". To me it appears to be something to do with the SVN Server rejecting external connections but I have no idea how this would happen. Any thoughts on what I can try from here? Thanks, Rob Edit: Network topology Production server sits externally to our in-house SVN server. Our IPCop (?) firewall allows connections from it (and it alone) on port 80 and passes the connection to the SVN Server. The hardware is all pretty decent and I don't doubt that its doing its job correctly, especially as iptables is seeing the new connections. subversion.conf (in /etc/httpd/conf.d) LoadModule dav_svn_module modules/mod_dav_svn.so <Location /repos> DAV svn SVNPath /var/svn/repos <LimitExcept PROPFIND OPTIONS REPORT> AuthType Basic AuthName "SVN Server" AuthUserFile /var/svn/svn-auth Require valid-user </LimitExcept> </Location> ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:5F:C8:3A inet addr:172.16.0.14 Bcast:172.16.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe5f:c83a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:32317 errors:0 dropped:0 overruns:0 frame:0 TX packets:632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2544036 (2.4 MiB) TX bytes:143207 (139.8 KiB) netstat -lntp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 1484/mysqld tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1135/rpcbind tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1351/sshd tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 1230/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 1575/master tcp 0 0 0.0.0.0:58401 0.0.0.0:* LISTEN 1153/rpc.statd tcp 0 0 0.0.0.0:5672 0.0.0.0:* LISTEN 1626/qpidd tcp 0 0 :::139 :::* LISTEN 1678/smbd tcp 0 0 :::111 :::* LISTEN 1135/rpcbind tcp 0 0 :::80 :::* LISTEN 1615/httpd tcp 0 0 :::22 :::* LISTEN 1351/sshd tcp 0 0 ::1:631 :::* LISTEN 1230/cupsd tcp 0 0 ::1:25 :::* LISTEN 1575/master tcp 0 0 :::445 :::* LISTEN 1678/smbd tcp 0 0 :::56799 :::* LISTEN 1153/rpc.statd iptables --list -v -n (when iptables is stopped) Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination iptables --list -v -n (when iptables is running, after one attempted svn connection) Chain INPUT (policy ACCEPT 68 packets, 6561 bytes) pkts bytes target prot opt in out source destination 19 1304 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 1 60 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:80 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 17 packets, 1612 bytes) pkts bytes target prot opt in out source destination tcpdump 17:08:18.455114 IP 'production server'.43255 > 'svn server'.local.http: Flags [S], seq 3200354543, win 5840, options [mss 1380,sackOK,TS val 2011458346 ecr 0,nop,wscale 7], length 0 17:08:18.455169 IP 'svn server'.local.http > 'production server'.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 816478 ecr 2011449346,nop,wscale 7], length 0 17:08:19.655317 IP 'svn server'.local.http > 'production server'k.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 817679 ecr 2011449346,nop,wscale 7], length 0

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• ldirectord ipvsadm not show reals ip and not work wtih pacemaker and corosync

  - by miguer27

  first thanks for your time. I'm having a problem with ldirectord that I can not solve, I comment my situation: I have two nodes with pace maker and corosync and configure somes resources: root@ldap1:/home/mamartin# crm status Last updated: Tue Jun 3 12:58:30 2014 Last change: Tue Jun 3 12:23:47 2014 via cibadmin on ldap1 Stack: openais Current DC: ldap2 - partition with quorum Version: 1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff 2 Nodes configured, 2 expected votes 7 Resources configured. Online: [ ldap1 ldap2 ] Resource Group: IPV_LVS IPV_4 (ocf::heartbeat:IPaddr2): Started ldap1 IPV_6 (ocf::heartbeat:IPv6addr): Started ldap1 lvs (ocf::heartbeat:ldirectord): Started ldap1 Clone Set: clon_IPV_lo [IPV_lo] Started: [ ldap2 ] Stopped: [ IPV_lo:1 ] root@ldap1:/home/mamartin# crm configure show node ldap2 \ attributes standby="off" node ldap1 \ attributes standby="off" primitive IPV-lo_4 ocf:heartbeat:IPaddr \ params ip="192.168.1.10" cidr_netmask="32" nic="lo" \ op monitor interval="5s" primitive IPV-lo_6 ocf:heartbeat:IPv6addrLO \ params ipv6addr="[fc00:1::3]" cidr_netmask="64" \ op monitor interval="5s" primitive IPV_4 ocf:heartbeat:IPaddr2 \ params ip="192.168.1.10" nic="eth0" cidr_netmask="25" lvs_support="true" \ op monitor interval="5s" primitive IPV_6 ocf:heartbeat:IPv6addr \ params ipv6addr="[fc00:1::3]" nic="eth0" cidr_netmask="64" \ op monitor interval="5s" primitive lvs ocf:heartbeat:ldirectord \ params configfile="/etc/ldirectord.cf" \ op monitor interval="20" timeout="10" \ meta target-role="Started" group IPV_LVS IPV_4 IPV_6 lvs group IPV_lo IPV-lo_6 IPV-lo_4 clone clon_IPV_lo IPV_lo \ meta interleave="true" target-role="Started" location cli-prefer-IPV_LVS IPV_LVS \ rule $id="cli-prefer-rule-IPV_LVS" inf: #uname eq ldap1 colocation LVS_no_IPV_lo -inf: clon_IPV_lo IPV_LVS property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1401264327" rsc_defaults $id="rsc-options" \ resource-stickiness="1000" The problem is in the ipvsadm only show a one real IP, when i configured two now, show the ldirector.cf: root@ldap1:/home/mamartin# ipvsadm IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags - RemoteAddress:Port Forward Weight ActiveConn InActConn TCP ldap-maqueta.cica.es:ldap wrr - ldap2.cica.es:ldap Route 4 0 0 TCP [[fc00:1::3]]:ldap wrr - [[fc00:1::2]]:ldap Route 4 0 0 root@ldap1:/home/mamartin# cat /etc/ldirectord.cf checktimeout=10 checkinterval=2 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=yes #ipv4 virtual=192.168.1.10:389 real=192.168.1.11:389 gate 4 real=192.168.1.12:389 gate 4 scheduler=wrr protocol=tcp checktype=on #ipv6 virtual6=[[fc00:1::3]]:389 real6=[[fc00:1::1]]:389 gate 4 real6=[[fc00:1::2]]:389 gate 4 scheduler=wrr protocol=tcp checkport=389 checktype=on and in the logs I see nothing clear: root@ldap1:/home/mamartin# ldirectord -d /etc/ldirectord.cf start DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.11:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.12:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Checking on: Real servers are added without any checks DEBUG2: Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Destination already exists root@ldap1:/home/mamartin# cat /var/log/ldirectord.log [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.11:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::2]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t [[fc00:1::3]]:389 -r [[fc00:1::2]]:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: [[fc00:1::2]]:389 ([[fc00:1::3]]:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::1]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: [[fc00:1::1]]:389 ([[fc00:1::3]]:389) (Weight set to 4) do not know if this is a bug or a configuration error, can anyone help? Regards.

  Read the article

• Help me upgrade my pf.conf for OpenBSD 4.7

  - by polemon

  I'm planning on upgrading my OpenBSD to 4.7 (from 4.6) and as you may or may not know, they changed the syntax for pf.conf. This is the relevant portion from the upgrade guide: pf(4) NAT syntax change As described in more detail in this mailing list post, PF's separate nat/rdr/binat (translation) rules have been replaced with actions on regular match/filter rules. Simple rulesets may be converted like this: nat on $ext_if from 10/8 -> ($ext_if) rdr on $ext_if to ($ext_if) -> 1.2.3.4 becomes match out on $ext_if from 10/8 nat-to ($ext_if) match in on $ext_if to ($ext_if) rdr-to 1.2.3.4 and... binat on $ext_if from $web_serv_int to any -> $web_serv_ext becomes match on $ext_if from $web_serv_int to any binat-to $web_serv_ext nat-anchor and/or rdr-anchor lines, e.g. for relayd(8), ftp-proxy(8) and tftp-proxy(8), are no longer used and should be removed from pf.conf(5), leaving only the anchor lines. Translation rules relating to these and spamd(8) will need to be adjusted as appropriate. N.B.: Previously, translation rules had "stop at first match" behaviour, with binat being evaluated first, followed by nat/rdr depending on direction of the packet. Now the filter rules are subject to the usual "last match" behaviour, so care must be taken with rule ordering when converting. pf(4) route-to/reply-to syntax change The route-to, reply-to, dup-to and fastroute options in pf.conf move to filteropts; pass in on $ext_if route-to (em1 192.168.1.1) from 10.1.1.1 pass in on $ext_if reply-to (em1 192.168.1.1) to 10.1.1.1 becomes pass in on $ext_if from 10.1.1.1 route-to (em1 192.168.1.1) pass in on $ext_if to 10.1.1.1 reply-to (em1 192.168.1.1) Now, this is my current pf.conf: # $OpenBSD: pf.conf,v 1.38 2009/02/23 01:18:36 deraadt Exp $ # # See pf.conf(5) for syntax and examples; this sample ruleset uses # require-order to permit mixing of NAT/RDR and filter rules. # Remember to set net.inet.ip.forwarding=1 and/or net.inet6.ip6.forwarding=1 # in /etc/sysctl.conf if packets are to be forwarded between interfaces. ext_if="pppoe0" int_if="nfe0" int_net="192.168.0.0/24" polemon="192.168.0.10" poletopw="192.168.0.12" segatop="192.168.0.20" table <leechers> persist set loginterface $ext_if set skip on lo match on $ext_if all scrub (no-df max-mss 1440) altq on $ext_if priq bandwidth 950Kb queue {q_pri, q_hi, q_std, q_low} queue q_pri priority 15 queue q_hi priority 10 queue q_std priority 7 priq(default) queue q_low priority 0 nat-anchor "ftp-proxy/*" rdr-anchor "ftp-proxy/*" nat on $ext_if from !($ext_if) -> ($ext_if) rdr pass on $int_if proto tcp to port ftp -> 127.0.0.1 port 8021 rdr pass on $ext_if proto tcp to port 2080 -> $segatop port 80 rdr pass on $ext_if proto tcp to port 2022 -> $segatop port 22 rdr pass on $ext_if proto tcp to port 4000 -> $polemon port 4000 rdr pass on $ext_if proto tcp to port 6600 -> $polemon port 6600 anchor "ftp-proxy/*" block pass on $int_if queue(q_hi, q_pri) pass out on $ext_if queue(q_std, q_pri) pass out on $ext_if proto icmp queue q_pri pass out on $ext_if proto {tcp, udp} to any port ssh queue(q_hi, q_pri) pass out on $ext_if proto {tcp, udp} to any port http queue(q_std, q_pri) #pass out on $ext_if proto {tcp, udp} all queue(q_low, q_hi) pass out on $ext_if proto {tcp, udp} from <leechers> queue(q_low, q_std) pass in on $ext_if proto tcp to ($ext_if) port ident queue(q_hi, q_pri) pass in on $ext_if proto tcp to ($ext_if) port ssh queue(q_hi, q_pri) pass in on $ext_if proto tcp to ($ext_if) port http queue(q_hi, q_pri) pass in on $ext_if inet proto icmp all icmp-type echoreq queue q_pri If someone has experience with porting the 4.6 pf.conf to 4.7, please help me do the correct changes. OK, this is how far I've got: I commented out nat-anchor and rdr-anchor, as describted in the guide: #nat-anchor "ftp-proxy/*" #rdr-anchor "ftp-proxy/*" And this is how I've "converted" the rdr rules: #nat on $ext_if from !($ext_if) -> ($ext_if) match out on $ext_if from !($ext_if) nat-to ($ext_if) #rdr pass on $int_if proto tcp to port ftp -> 127.0.0.1 port 8021 match in on $int_if proto tcp to port ftp rdr-to 127.0.0.1 port 8021 #rdr pass on $ext_if proto tcp to port 2080 -> $segatop port 80 match in on $ext_if proto tcp tp port 2080 rdr-to $segatop port 80 #rdr pass on $ext_if proto tcp to port 2022 -> $segatop port 22 match in on $ext_if proto tcp tp port 2022 rdr-to $segatop port 22 rdr pass on $ext_if proto tcp to port 4000 -> $polemon port 4000 match in on $ext_if proto tcp tp port 4000 rdr-to $polemon port 4000 rdr pass on $ext_if proto tcp to port 6600 -> $polemon port 6600 match in on $ext_if proto tcp tp port 6600 rdr-to $polemon port 6600 Did I miss anything? Is the anchor for ftp-proxy OK as it is now? Do I need to change something in the other pass in on... lines?

  Read the article

• How to use CLEAR USB WiMax in Ubuntu (host) and Windows XP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for Linux as yet. I've installed Windows XP as guest in Ubuntu and the version I'm using is 3.2.2. USB is connecting fine in Windows XP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

< Previous Page | 34 35 36 37 38 39 40  | Next Page >