Search Results

Search found 18109 results on 725 pages for 'down'.

Page 38/725 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

• How to configure an Ubuntu 12.04 virtual server and VMWare ESXi5 the way VMWare would be able to shut it down properly?

  - by Ivan

  I run an Ubuntu 12.04 server as a virtual machine on a VMWare ESXi 5 server. I've configured VMWare to shut the quest machines down the sane way (with an ACPI (if I understand it righ) shutdown signal so that guest OSes would do it). And this works with other VMs (running Windows 7 Professional and openSuSE) but doesn't work with the Ubuntu server - VMWare still offers just to power them off when I ask it to stop the guest. Any ideas how to fix this?

  Read the article

• python extract from switch output

  - by household2

  I have some info back from a LAN switch as below Vlan 1 is administratively down, line protocol is down Vlan 2 is up, line protocol is up Helper address is 192.168.0.2 Vlan 3 is up, line protocol is up Helper address is not set Vlan 4 is up, line protocol is up Helper address is 192.168.0.2 Vlan 5 is down, line protocol is down Helper address is 192.168.0.2 Vlan 6 is down, line protocol is down Helper address is not set Helper address is not set And the output I'm trying for is Vlan 1,admin down,n/a Vlan 2,up/up, 192.168.0.2 Vlan 3, up/up, not set Vlan 4, up/up, 192.168.0.2 Vlan 5, down/down, 192.168.0.2 Vlan 6, down/down, not set So the helper isn't always there (line 1) sometimes it's set sometimes it isn't, sometimes there are two lines (last Vlan - I only need 1) and the Vlan can have states of admin down, up/up, up/down (not here) and down down. So using Python and pexpect I can get the above output, but I'm having difficulty parsing out the consecutive lines. I've tried enumerate and then use key+1 for the next line, but the fact that there can be 0,1 or 2 lines following the Vlan screws me. Any ideas please?

  Read the article

• How should I configure my Active Directory servers so that if one goes down, users are not kicked off SQL?

  - by Matty Brown

  Today, we shut down one of our Active Directory servers during office hours to check the loading on a UPS. Since all the server did was provide Active Directory in a separate building incase the main building caught fire, or whatever, we didn't think it would have any effect on our users. Seconds after the server was shut down, we had a dozen phone calls from users experiencing this issue:- [Microsoft SQL Server Login] SQLState: '28000' [Microsoft][ODBC SQL Server Driver][SQL Server]Login failed. The login is from an untrusted domain and cannot be used with authentication. Once we realized what had happened, we quickly rebooted the down Active Directory server. Problem solved. But why did this happen. And what if one day a server has a breakdown and is offline for hours, or days? Shouldn't the other Active Directory servers in the domain service authentication requests without disruption to users? We have 3 Windows Server 2003 Standard servers running Active Directory as Domain Controllers with Global Catalogs, all physically located on the same network at Gigabit speeds. I believe the domain was originally Windows Server 2000, or maybe even NT 4.0. Could the issue be to down to old Group Policies inherited from these old server OS's, or some default setting in Active Directory that needs changing?

  Read the article

• Why is my HP TouchSmart tx2 1025dx shutting down?

  - by Kristy

  I'm having an issue with my HP tx2 1025dx laptop. Sometimes it will spontaneously shut itself off. First, the screen will go out. Next, the computer itself will shut down. This usually occurs when I am doing something that requires a lot of resources, but lately can happen when I am doing something as simple as using an Office app. I think it may be heat related, if I try to boot the laptop after it shuts itself down, it will shut itself down again before startup is complete. If I let it cool down for a while and then come back to it, the computer will boot properly. These shutdowns are always accompanied by high temperatures on the bottom right side, as well as the right side of the keyboard. I am using a laptop cooler with two fans, and it is not making a bit of difference. This is the second TouchSmart we have owned, the first one had the same issues, we sent it in to HP after it finally refused to reboot. They “fixed” it, and it worked fine for about a month before doing the exact same thing. Unfortunately we had bought the second one before the issues began with the original, if I had known this would be a problem, I would not have purchased another TouchSmart. This particular laptop we have had for more than a year and it didn’t start these issues until a couple of months ago. Any suggestions as to how to fix this problem?

  Read the article

• Delicious is Shutting Down. Here’s How to Migrate to Diigo Instead

  - by Trevor Bekolay

  Today we’ve learned that Yahoo is shutting down Delicious, a fairly popular online service that let you organize your bookmarks, so if you want to get your bookmarks out and migrate to another service, here’s how to do it. You can use the export tool to easily get a copy of your bookmarks, and then use that file to import into any number of places, including your regular browser bookmarks. We’ve done some research and found Diigo, a very similar tool to Delicious, which you can use instead Latest Features How-To Geek ETC The Complete List of iPad Tips, Tricks, and Tutorials The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor Exploring the Jungle Ruins Wallpaper Protect Your Privacy When Browsing with Chrome and Iron Browser Free Shipping Day is Friday, December 17, 2010 – National Free Shipping Day Find an Applicable Quote for Any Programming Situation Winter Theme for Windows 7 from Microsoft Score Free In-Flight Wi-Fi Courtesy of Google Chrome

  Read the article

• Graphics Driver problem, ATI Radeon HD 3200, small screen size and slows everything down.

  - by Arvind Jangid

  Regards. I am using a: 2009 Compaq Presario CQ40-415AU Notebook AMD Athlon X2 Dual core Processor 2.1 GHz 1024 MB L2 cache 3GB DDR2 RAM ATI Radeon + HD 3200 Graphics 256 MB, screen is 14 inch widescreen with resolution of 1280*800. I installed Ubuntu 12.04 LTS 32bit on my laptop. It works brilliantly until I installed graphics driver. When I installed the driver, the graphics became slow. Everything slowed down. Even the splash screen resolution changed to something like 640*480. I have liked Ubuntu since 9.10 and for the freedom it provides and its versatility, but graphics problem remains the same. I even installed Ubuntu on a 50 GB partition with 6 GB swap partition. My HDD is 320 GB. Please tell me what is wrong.

  Read the article

• What collision detection approach for top down car game?

  - by nathan

  I have a quite advanced top down car game and i use masks to detect collisions. I have the actual designed track (what the player see) with fancy graphics etc. and two other pictures i use as mask for my detection collisions. Each mask has only two colors, white and black and i check each frame if a pixel of the car collide with a black pixel of the masks. This approach works of course but it's not really flexible. Whenever i want to change the look of a track, i have to redraw the mask and it's a real pain. What is the general approach for this kind of game? How can i improve the flexibility of such a mask based approach?

  Read the article

• After how much line of code a function should be break down?

  - by Sumeet

  While working on existing code base, I usually come across procedures that contain Abusive use of IF and Switch statements. The procedures consist of overwhelming code, which I think require re-factoring badly. The situation gets worse when I identify that some of these are recursive as well. But this is always a matter of debate as the code is working fine and no one wants to wake up the dragon. But, everyone accepts it is very expensive code to manage. I am wondering if are any recommendations to determine if a particular Method is a culprit and needs a revisit/rewrite , so that it can broken down or polymophized in an effective manner. Are there any Metrics (like no. of lines in procedure) that can be used to identify such segment of code. The checklist or advice to convince everyone, will be great!

  Read the article

• Why the amount of 'indexed' images can go down?

  - by Roman Matveev

  I have a site with several thousand of images. All those images included into the sitemap submitted to Google Webmaster Tools. The amount of 'submitted' images is OK, but the amount of 'indexed' is significantly lower than the amount of 'submitted' and it is going DOWN! I'd understand if not all of my images got indexed (however it is also not clear and very frustrating for me) but I can not understand how the indexing can go in the negative direction?! All the images stays on their places. And pages containing them stays unchanged. At least they intended to be. Any thoughts?

  Read the article

• Unity3D problem. Bullets fall down instead of flying like they should

  - by user2342080

  I used this tutorial as a reference. http://www.youtube.com/watch?v=3L8eaoyZ0Go My problem is that whenever I play the game, EVERYTHING works but the bullets. It just falls down instead of flying forward. This is the flash version of the game: http://v1k.me/swf/ Can some one help me out? Should I upload the project? This is my "Shoot.js": public var bulletPrefab : Transform; public var bulletSpeed : float = 20; function Update() { if(Input.GetMouseButton(0)) { if(bulletPrefab || bulletSpeed) { var bulletCreate = Instantiate(bulletPrefab, GameObject.Find("SpawnPoint").transform.position, Quaternion.identity); bulletCreate.rigidbody.AddForce(transform.forward * bulletSpeed); } } }

  Read the article

• Hide GRUB2 menu UNLESS you hold down Shift key: how to make this happen?

  - by Shasteriskt

  I have a Ubuntu - Windows 7 dual-boot set-up, and I would like to have it that my laptop would boot up Windows 7 unless I press down the Shift key right after boot and bring up the Grub2 menu from which I can choose Ubuntu. I researched on Grub2 and options for etc/default/grub and I have tried playing around with combinations with the GRUB_TIMEOUT and GRUB_HIDDEN_TIMEOUT values, but to no avail. I tried setting the GRUB_HIDDEN_TIMEOUT higher than the GRUB_TIMEOUT thinking that both countdown start simultaneously, but no - GRUB_TIMEOUT only starts after the other is done. Is this behavior achievable? If so, how?

  Read the article

• Managed servers getting down regularly by Node Manager. WAD?

  - by csoto

  Recently I have been working on a service request where several instances were running, and several technologies were being used, including SOA, BAM, BPEL and others. At a first glance, this may seem to be a Node Manager problem. But on this situation, the problem was at JMS - Persistent Store level. Node Manager can automatically restart Managed Servers that have the "failed" health state, or have shut down unexpectedly due to a system crash or reboot. As a matter of fact, from the provided log files it was clear that the instance was becoming unhealthy because of a persist6ent Store problem. So finally, the problem here was not with Node Manager as it was working as designed, and the restart was being caused by the Persistent Store. After this Persistent Store problem was fixed, everuthing went fine. This particular issue that I worked was on an Exalogic machine, but note that this may happen on any hardware running Weblogic.

  Read the article

• How to recover organic position in Google results after server down?

  - by ElHaix

  I have several sites that were doing quite well in terms of organic SEO rankings. I have the important sites setup in Google's Webmaster tools. Long story short, the system was down for about two weeks. Now in AdSense and Analytics, I am seeing that the page views are SLOWLY increasing. and I would like to know if there is anything I can do now to try to expedite the process of regaining those positions. Since there were several errors from that server, is it possible that Google will now rank any site from that IP address lower due to those two weeks of errors? Is this something that I just have to let ride out? Thanks.

  Read the article

• Can emsripten compile down to Canvas-based Js instead of WebGL?

  - by Sebastian Scholle

  I understand that emscripten compiles down LLVM to JS and it converts OpenGL Calls to WebGL. Thats a fairly simple translation. Is there a way to tell emscripten to use some other graphics Library ( for example Pixi JS ) for its rendering code translations? Is the compiled JS code easy to update or would it be better to merge in your own Graphics API that handles WebGL/Canvas calls. IE: can we use a C++ Graphics Wrapper Library that when compiles to JS, will simply plug into our own JS Graphics Wrapper Library? Im assuming YES, but has anyone tried this? And if So, what would be your technique, as my C++ skills are basic.

  Read the article

• In terms of SEO, is it better to have a URL broken down by folder, or with dashed names?

  - by VictorKilo

  I am creating a friendly url interpreter for my website. I have read dozens of similar topics on this site, but none that seem to address my particular situation. What I want to know is if it's better to have: A well broken down URL where each category is represented by a folder domain.com/1036/OR/Lane/Lowell/Wetleau-Subdivision -OR- A URL which groups all of the categories and terms together domain.com/1036/Wetleau-Subdivision-Lowell-OR-Lane I am asking only in terms of what is best for SEO, not necessarily human readability. My thinking is that it may be better to group them all together like they are in the second example. My reasoning being that all of those terms represent the page and are more likely to draw a result. I am a complete SEO nub though, and I crave some expert guidance. Thank you in advance for any help given.

  Read the article

• What's the best way to know if your web server goes down?

  - by Mike Christensen

  I noticed my website only got 8 visitors today, which means it probably went down very early this morning and I never noticed. Why it went down is another story. Ideally, I'd like to be emailed if my web server becomes unresponsive or does not return an HTTP 200. Is there either a cloud-based service (either free or pretty cheap) that can monitor your website? If not, is there a good free/open source program I can run on either a Linux or Windows machine that will monitor a website and email me if it goes down? Thanks!

  Read the article

• Is it possible to make the Numpad 5 button work as the Numpad Down button while Num Lock is on?

  - by Eddy

  I hope someone can help me out with this; I use a laptop and I like to play games a lot that are arrow key dependent. So after a while of using my laptop, I accidentally broke the Down Arrow key. So I decided to try and find out how to make the Numpad5 button work as the Numpad Down button while Numlock is on. I was trying to use AutoHotkey, but so far I've had no luck. Can anyone help me out with this? So far the scripts I used that didn't work were Numpad5::NumpadDown or Numpad5::Down. Am I doing something wrong here?

  Read the article

• Windows server's HDD Spin down daily/nightly - Does it makes sense?

  - by Riccardo

  A Windows Server 2003 R2 has the following hard disk configuration: - 3 internal hard disks attached to a 3Ware unit, configured in Raid 1 + spare unit - 3 external USB backup disks: 2 Verbatim 1TB (Samsung HD103SI) + 1 Western Digital 1TB (WD10EADS) The server runs 365 days per year, h24, however: - at daytime the server/user usage is limited to the internal hard disks - at nighttime there's no user usage, apart from scheduled maintenance tasks, basically the Server will be idle from 7PM to 8AM. apart from nighly backups (few hours). I was wondering if: (a) it makes any sense let Windows manage power savings, allowing disks to spin down accordingly, ** OR** let the disks stay awlays-on, to avoid permature wearing, due to continuous spin up/down (b) leave internal disks always on, and force external disks to power down while idle (this requires third party tools, such as Verbatim's Green button utility) Your thoughts?

  Read the article

• How can HAProxy improve availibility, or "how can I prevent my site from going down"? [closed]

  - by Joe Hopfgartner

  I am aware of what HAProxy does, but what if my HAproxy goes down? Or what if my DNS servers go down? Yes, dns is less the problem. However dns only solves to an IP and an IP is announced via BGP to be routed over some router. What if that router goes down? Of course if I have complicated application servers that are likely to fail HAProxy can significantly improve uptime. But my application isnt. In fact my application may very well just be delivering a small static html file via HTTP. Basically if any user anywhere types in MYDOMAIN.COM, I want the user to get SOMETHING on the screen other than a timeout or DNS resolution error. How can I do that? The point of entry is difficult. The so called "initial closure mechanism".

  Read the article

• Is it possible to have tab completion of drop-down lists in web pages in Firefox?

  - by Nick Booker

  Does anyone know of a Firefox plugin that would enable tab-completion (or some other key sequence like Alt-L) of items in drop-down lists in web forms? e.g. ou<TAB>in<TAB>s<TAB> for 'OurCompany - Internal Support' Vimperator's hints mode makes it very ergonomic to focus the drop-down list with a key sequence like f13 but the keyboard interface to the drop-down list still sucks. I very frequently have to pick items from a very long list with very long common prefixes among the entries (e.g. 30-40 starting with OurCompany -), which renders both the built-in keyboard interface and the mouse pretty slow and unergonomic. I basically want readline support for filling webforms!

  Read the article

• unexplainable packet drops with 5 ethernet NICs and low traffic on Ubuntu

  - by jon

  I'm stuck on problem where my machine started to drops packets with no sign of ANY system load or high interrupt usage after an upgrade to Ubuntu 12.04. My server is a network monitoring sensor, running Ubuntu LTS 12.04, it passively collects packets from 5 interfaces doing network intrusion type stuff. Before the upgrade I managed to collect 200+GB of packets a day while writing them to disk with around 0% packet loss depending on the day with the help of CPU affinity and NIC IRQ to CPU bindings. Now I lose a great deal of packets with none of my applications running and at very low PPS rate which a modern workstation NIC would have no trouble with. Specs: x64 Xeon 4 cores 3.2 Ghz 16 GB RAM NICs: 5 Intel Pro NICs using the e1000 driver (NAPI). [1] eth0 and eth1 are integrated NICs (in the motherboard) There are 2 other PCI-X network cards, each with 2 Ethernet ports. 3 of the interfaces are running at Gigabit Ethernet, the others are not because they're attached to hubs. Specs: [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm uptime 17:36:00 up 1:43, 2 users, load average: 0.00, 0.01, 0.05 # uname -a Linux nms 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I also have the CPU governor set to performance mode and irqbalance off. The problem still occurs with them on. # lspci -t -vv -[0000:00]-+-00.0 Intel Corporation E7520 Memory Controller Hub +-02.0-[01-03]--+-00.0-[02]----0e.0 Dell PowerEdge Expandable RAID controller 4 | \-00.2-[03]-- +-04.0-[04]-- +-05.0-[05-07]--+-00.0-[06]----07.0 Intel Corporation 82541GI Gigabit Ethernet Controller | \-00.2-[07]----08.0 Intel Corporation 82541GI Gigabit Ethernet Controller +-06.0-[08-0a]--+-00.0-[09]--+-04.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | | \-04.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-00.2-[0a]--+-02.0 Digium, Inc. Wildcard TE210P/TE212P dual-span T1/E1/J1 card 3.3V | +-03.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-03.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) +-1d.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 +-1d.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 +-1d.2 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 +-1d.7 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller +-1e.0-[0b]----0d.0 Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] +-1f.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge \-1f.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller I believe the NIC nor the NIC drivers are dropping the packets because ethtool reports 0 under rx_missed_errors and rx_no_buffer_count for each interface. On the old system, if it couldn't keep up this is where the drops would be. I drop packets on multiple interfaces just about every second, usually in small increments of 2-4. I tried all these sysctl values, I'm currently using the uncommented ones. # cat /etc/sysctl.conf # high net.core.netdev_max_backlog = 3000000 net.core.rmem_max = 16000000 net.core.rmem_default = 8000000 # defaults #net.core.netdev_max_backlog = 1000 #net.core.rmem_max = 131071 #net.core.rmem_default = 163480 # moderate #net.core.netdev_max_backlog = 10000 #net.core.rmem_max = 33554432 #net.core.rmem_default = 33554432 Here's an example of an interface stats report with ethtool. They are all the same, nothing is out of the ordinary ( I think ), so I'm only going to show one: ethtool -S eth2 NIC statistics: rx_packets: 7498 tx_packets: 0 rx_bytes: 2722585 tx_bytes: 0 rx_broadcast: 327 tx_broadcast: 0 rx_multicast: 1504 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 1504 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 0 tx_tcp_seg_failed: 0 rx_flow_control_xon: 0 rx_flow_control_xoff: 0 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 2722585 rx_csum_offload_good: 0 rx_csum_offload_errors: 0 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 01 # ifconfig eth0 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:373348 errors:16 dropped:95 overruns:0 frame:16 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:356830572 (356.8 MB) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8d UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:13616 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8690528 (8.6 MB) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 00:04:23:e1:77:6a UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:7750 errors:0 dropped:471 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2780935 (2.7 MB) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 00:04:23:e1:77:6b UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:5112 errors:0 dropped:206 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:639472 (639.4 KB) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:04:23:b6:35:6c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:961467 errors:0 dropped:935 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:958561305 (958.5 MB) TX bytes:0 (0.0 B) eth5 Link encap:Ethernet HWaddr 00:04:23:b6:35:6d inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4264 errors:0 dropped:16 overruns:0 frame:0 TX packets:699 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:572228 (572.2 KB) TX bytes:124456 (124.4 KB) I tried the defaults, then started to play around with settings. I wasn't using any flow control and I increased the RxDescriptor count to 4096 before the upgrade as well without any problems. # cat /etc/modprobe.d/e1000.conf options e1000 XsumRX=0,0,0,0,0 RxDescriptors=4096,4096,4096,4096,4096 FlowControl=0,0,0,0,0 debug=16 Here's my network configuration file, I turned off checksumming and various offloading mechanisms along with setting CPU affinity with heavy use interfaces getting an entire CPU and light use interfaces sharing a CPU. I used these settings prior to the upgrade without problems. # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual pre-up /sbin/ethtool -G eth0 rx 4096 tx 0 pre-up /sbin/ethtool -K eth0 gro off gso off rx off pre-up /sbin/ethtool -A eth0 rx off autoneg off up ifconfig eth0 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/48/smp_affinity down ifconfig eth0 down post-down /sbin/ethtool -G eth0 rx 256 tx 256 post-down /sbin/ethtool -K eth0 gro on gso on rx on post-down /sbin/ethtool -A eth0 rx on autoneg on auto eth1 iface eth1 inet manual pre-up /sbin/ethtool -G eth1 rx 4096 tx 0 pre-up /sbin/ethtool -K eth1 gro off gso off rx off pre-up /sbin/ethtool -A eth1 rx off autoneg off up ifconfig eth1 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/49/smp_affinity down ifconfig eth1 down post-down /sbin/ethtool -G eth1 rx 256 tx 256 post-down /sbin/ethtool -K eth1 gro on gso on rx on post-down /sbin/ethtool -A eth1 rx on autoneg on auto eth2 iface eth2 inet manual pre-up /sbin/ethtool -G eth2 rx 4096 tx 0 pre-up /sbin/ethtool -K eth2 gro off gso off rx off pre-up /sbin/ethtool -A eth2 rx off autoneg off up ifconfig eth2 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "1" > /proc/irq/82/smp_affinity down ifconfig eth2 down post-down /sbin/ethtool -G eth2 rx 256 tx 256 post-down /sbin/ethtool -K eth2 gro on gso on rx on post-down /sbin/ethtool -A eth2 rx on autoneg on auto eth3 iface eth3 inet manual pre-up /sbin/ethtool -G eth3 rx 4096 tx 0 pre-up /sbin/ethtool -K eth3 gro off gso off rx off pre-up /sbin/ethtool -A eth3 rx off autoneg off up ifconfig eth3 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "2" > /proc/irq/83/smp_affinity down ifconfig eth3 down post-down /sbin/ethtool -G eth3 rx 256 tx 256 post-down /sbin/ethtool -K eth3 gro on gso on rx on post-down /sbin/ethtool -A eth3 rx on autoneg on auto eth4 iface eth4 inet manual pre-up /sbin/ethtool -G eth4 rx 4096 tx 0 pre-up /sbin/ethtool -K eth4 gro off gso off rx off pre-up /sbin/ethtool -A eth4 rx off autoneg off up ifconfig eth4 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/77/smp_affinity down ifconfig eth4 down post-down /sbin/ethtool -G eth4 rx 256 tx 256 post-down /sbin/ethtool -K eth4 gro on gso on rx on post-down /sbin/ethtool -A eth4 rx on autoneg on auto eth5 iface eth5 inet static pre-up /etc/fw.conf address 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 192.168.1.2 192.168.1.3 up ifconfig eth5 up post-up echo "8" > /proc/irq/77/smp_affinity down ifconfig eth5 down Here's a few examples of packet drops, i ran one after another, probabling totaling 3 or 4 seconds. You can see increases in the drops from the 1st and 3rd. This was a non-busy time, very little traffic. # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 505 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 507 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 227 lo: 0 eth2: 512 eth1: 0 eth5: 17 eth0: 105 eth4: 1039 I tried the pci=noacpi options. With and without, it's the same. This is what my interrupt stats looked like before the upgrade, after, with ACPI on PCI it showed multiple NICs bound to an interrupt and shared with other devices such as USB drives which I didn't like so I think i'm going to keep it with ACPI off as it's easier to designate sole purpose interrupts. Is there any advantage I would have using the default i.e. ACPI w/ PCI. ? # cat /etc/default/grub | grep CMD_LINE GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 noacpi pci=noacpi" GRUB_CMDLINE_LINUX="" # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 0: 45 0 0 16 IO-APIC-edge timer 1: 1 0 0 7936 IO-APIC-edge i8042 2: 0 0 0 0 XT-PIC-XT-PIC cascade 6: 0 0 0 3 IO-APIC-edge floppy 8: 0 0 0 1 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-edge acpi 12: 0 0 0 1809 IO-APIC-edge i8042 14: 1 0 0 4498 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 0 0 0 1350 IO-APIC-fasteoi uhci_hcd:usb4, radeon 19: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3 23: 0 0 0 4099 IO-APIC-fasteoi ehci_hcd:usb1 38: 0 0 0 61963 IO-APIC-fasteoi megaraid 48: 0 0 1002319 4 IO-APIC-fasteoi eth0 49: 0 0 38772 3 IO-APIC-fasteoi eth1 77: 0 0 130076 432159 IO-APIC-fasteoi eth4 78: 0 0 0 23917 IO-APIC-fasteoi eth5 82: 1329033 0 0 4 IO-APIC-fasteoi eth2 83: 0 4886525 0 6 IO-APIC-fasteoi eth3 NMI: 5 6 4 5 Non-maskable interrupts LOC: 61409 57076 64257 114764 Local timer interrupts SPU: 0 0 0 0 Spurious interrupts IWI: 0 0 0 0 IRQ work interrupts RES: 17956 25333 13436 14789 Rescheduling interrupts CAL: 22436 607 539 478 Function call interrupts TLB: 1525 1458 4600 4151 TLB shootdowns TRM: 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 Machine check exceptions MCP: 16 16 16 16 Machine check polls ERR: 0 MIS: 0 Here's sample output of vmstat, showing the system. Barebones system right now. root@nms:~# vmstat -S m 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 14992 192 1029 0 0 56 2 419 29 1 0 99 0 0 0 0 14992 192 1029 0 0 0 0 922 27 0 0 100 0 0 0 0 14991 192 1029 0 0 0 36 763 50 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 646 35 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 722 54 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 793 27 0 0 100 0 ^C Here's dmesg output. I can't figure out why my PCI-X slots are negotiated as PCI. The network cards are all PCI-X with the exception of the integrated NICs that came with the server. In the output below it looks as if eth3 and eth2 negotiated at PCI-X speeds rather than PCI:66Mhz. Wouldn't they all drop to PCI:66Mhz? If your integrated NICs are PCI, as labeled below (eth0,eth1), then wouldn't all devices on your bus speed drop down to that slower bus speed? If not, I still don't know why only one of my NICs ( each has two ethernet ports) is labeled as PCI-X in the output below. Does that mean it is running at PCI-X speeds are is it showing that it's capable? # dmesg | grep e1000 [ 3678.349337] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3678.349342] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3678.349394] e1000 0000:06:07.0: PCI->APIC IRQ transform: INT A -> IRQ 48 [ 3678.409725] e1000 0000:06:07.0: Receive Descriptors set to 4096 [ 3678.409730] e1000 0000:06:07.0: Checksum Offload Disabled [ 3678.409734] e1000 0000:06:07.0: Flow Control Disabled [ 3678.586409] e1000 0000:06:07.0: eth0: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8c [ 3678.586419] e1000 0000:06:07.0: eth0: Intel(R) PRO/1000 Network Connection [ 3678.586642] e1000 0000:07:08.0: PCI->APIC IRQ transform: INT A -> IRQ 49 [ 3678.649854] e1000 0000:07:08.0: Receive Descriptors set to 4096 [ 3678.649859] e1000 0000:07:08.0: Checksum Offload Disabled [ 3678.649863] e1000 0000:07:08.0: Flow Control Disabled [ 3678.826436] e1000 0000:07:08.0: eth1: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8d [ 3678.826444] e1000 0000:07:08.0: eth1: Intel(R) PRO/1000 Network Connection [ 3678.826627] e1000 0000:09:04.0: PCI->APIC IRQ transform: INT A -> IRQ 82 [ 3679.093266] e1000 0000:09:04.0: Receive Descriptors set to 4096 [ 3679.093271] e1000 0000:09:04.0: Checksum Offload Disabled [ 3679.093275] e1000 0000:09:04.0: Flow Control Disabled [ 3679.130239] e1000 0000:09:04.0: eth2: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6a [ 3679.130246] e1000 0000:09:04.0: eth2: Intel(R) PRO/1000 Network Connection [ 3679.130449] e1000 0000:09:04.1: PCI->APIC IRQ transform: INT B -> IRQ 83 [ 3679.397312] e1000 0000:09:04.1: Receive Descriptors set to 4096 [ 3679.397318] e1000 0000:09:04.1: Checksum Offload Disabled [ 3679.397321] e1000 0000:09:04.1: Flow Control Disabled [ 3679.434350] e1000 0000:09:04.1: eth3: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6b [ 3679.434360] e1000 0000:09:04.1: eth3: Intel(R) PRO/1000 Network Connection [ 3679.434553] e1000 0000:0a:03.0: PCI->APIC IRQ transform: INT A -> IRQ 77 [ 3679.704072] e1000 0000:0a:03.0: Receive Descriptors set to 4096 [ 3679.704077] e1000 0000:0a:03.0: Checksum Offload Disabled [ 3679.704081] e1000 0000:0a:03.0: Flow Control Disabled [ 3679.738364] e1000 0000:0a:03.0: eth4: (PCI:33MHz:64-bit) 00:04:23:b6:35:6c [ 3679.738371] e1000 0000:0a:03.0: eth4: Intel(R) PRO/1000 Network Connection [ 3679.738538] e1000 0000:0a:03.1: PCI->APIC IRQ transform: INT B -> IRQ 78 [ 3680.046060] e1000 0000:0a:03.1: eth5: (PCI:33MHz:64-bit) 00:04:23:b6:35:6d [ 3680.046067] e1000 0000:0a:03.1: eth5: Intel(R) PRO/1000 Network Connection [ 3682.132415] e1000: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.224423] e1000: eth1 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.316385] e1000: eth2 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.408391] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.500396] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.708401] e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX At first I thought it was the NIC drivers but I'm not so sure. I really have no idea where else to look at the moment. Any help is greatly appreciated as I'm struggling with this. If you need more information just ask. Thanks! [1]http://www.cs.fsu.edu/~baker/devices/lxr/http/source/linux/Documentation/networking/e1000.txt?v=2.6.11.8 [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm

  Read the article

• How would i down-sample a .wav file then reconstruct it using nyquist? - in matlab [closed]

  - by martin

  This is all done in MatLab 2010 My objective is to show the results of: undersampling, nyquist rate/ oversampling First i need to downsample the .wav file to get an incomplete/ or impartial data stream that i can then reconstuct. Heres the flow chart of what im going to be doing So the flow is analog signal - sampling analog filter - ADC - resample down - resample up - DAC - reconstruction analog filter what needs to be achieved: F= Frequency F(Hz=1/s) E.x. 100Hz = 1000 (Cyc/sec) F(s)= 1/(2f) Example problem: 1000 hz = Highest frequency 1/2(1000hz) = 1/2000 = 5x10(-3) sec/cyc or a sampling rate of 5ms This is my first signal processing project using matlab. what i have so far. % Fs = frequency sampled (44100hz or the sampling frequency of a cd) [test,fs]=wavread('test.wav'); % loads the .wav file left=test(:,1); % Plot of the .wav signal time vs. strength time=(1/44100)*length(left); t=linspace(0,time,length(left)); plot(t,left) xlabel('time (sec)'); ylabel('relative signal strength') **%this is were i would need to sample it at the different frequecys (both above and below and at) nyquist frequency.*I think.*** soundsc(left,fs) % shows the resaultant audio file , which is the same as original ( only at or above nyquist frequency however) Can anyone tell me how to make it better, and how to do the various sampling at different frequencies?

  Read the article

• How do you keep cool when production system goes down?

  - by Mag20

  This has happened to most of us... You come to work one day. Everything seems normal: the sun is shining, birds are chirping, but you notice a couple of weird things on your way to work like deja vu with cat in matrix. You get into office, there are a lot of phones ringing, but could be that they are just doing a new sales promotion. You settle in, when you notice a dark cloud hovering over you. It takes you a couple of moments, but you recognize the cloud is your boss. Usually he checks on you every morning with his "Soooo Peeeeter, how about those TCP/IP reports?" routine, but today he forgot everything about common manners and rudely invaded your personal space. No "Good Morning", just some drooling, grunts and curses. He reminds you a bit of neanderthal who is trying to get away from cyber tooth tiger, fear and panic all compressed in a tight ball. You try to decipher the new language that he created since yesterday and you start understanding that something bad happened overnight - production system went down. Now, your system is usually used by clients during regular working hours from 9-5, but for whatever reason you didn't get any alerts on your beeper (for people under 30 - beeper was like a mobile phone that could only ring and tell you who beeped you). Need to remember to charge it next time. So it is 8:45am, the system MUST be up at 9am. Every 10 seconds, your boss lets out yet another curse which communicates to you that another customer is having problems getting into the system. Also several account managers are now hovering over your boss trying to make him understand how clients are REALLY REALLY suffering. Everyone is depending on you to get the system up ASAP and at the same time hinder your progress by constantly distracting you. How do you keep cool in a situation like this?

  Read the article

• Implementing an automatic navigation mesh generation for 2d top down map?

  - by J2V

  I am currently in the middle of implementing an A* pathfinding for enemies. In order to implement the actual A* logic, I need a navigation mesh for my map. I am working on a 2D top down rpg map. The world is static, meaning there is no requirement for dynamic runtime mesh generation. My world objects are pixel based, not tile based and have associated data with them such as scale, rotation, origin etc. I will obviously need some vertex data being generated from my world objects, maybe create a polygon generation from color data? I could create a colormap with objects for my whole map, but I have no idea how to begin creating nav mesh polygons. How would an actual navigation mesh generation look like with this kind of available information? Can anyone maybe point to some great resources? I have looked into some 3D nav mesh tools, but they seem kind of overly complex for my situation and also have a lot of their req data available from models. Thanks a lot in advance! I have been trying to get my head around it for some time now.

  Read the article

• Can't mount USB devices, shut down etc. as a user

  - by Alok

  I tried gnome3 and gnome3-staging ppas to test running Gnome 3.8. After a while I decided that Gnome 3.8 wasn't for me, so I did a ppa-purge of both the ppas. As described in gnome3-staging ppa page, I also did: $ sudo apt-get purge libpam-systemd $ sudo apt-get install libpam-xdg-support The trouble is, I can't mount my external USB device anymore. When I try to mount it as a user, it fails: $ udisks --mount /dev/sdc1 Mount failed: Not Authorized I am logged in an XFCE session, but the same thing happens in a fallback Gnome session, or from a Unity session. Also, in XFCE, "suspend" and "shut down" menus are grayed out. I can't also open synaptic package manager from XFCE menus (sudo synaptic works). After a lot of searching, it seems like it is a policykit issue. I see the following in my ~/.xsession-errors: (polkit-gnome-authentication-agent-1:5805): polkit-gnome-1-WARNING **: Unable to determine the session we are in: No session for pid 5805 PID 5805 doesn't exist. If I try to start polkit-dnome-authentication-agent-1 from an xterm, I get the same error (different PID): $ /usr/lib/policykit-1-gnome/polkit-gnome-authentication-agent-1 ... (polkit-gnome-authentication-agent-1:15971): polkit-gnome-1-WARNING **: Unable to determine the session we are in: No session for pid 15971 (the ... lines are warnings from GTK about missing css files etc.). polkitd is running: $ pidof polkitd 1495 Is there something I am missing?

  Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >