Search Results

Search found 18637 results on 746 pages for 'network printers'.

Page 38/746 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

• Can't ping Ubuntu laptop from my LAN

  - by oskar

  My laptop has Ubuntu 10.10 and is connected to my router with full internet access, yet I can't ping it from other computers on my LAN. I tried the following: I can successfully ping those other computers from my Ubuntu laptop, so I didn't accidentally connect to someone else's network. I can successfully ping my Ubuntu laptop from itself, though I don't know if that means anything. I haven't messed with iptables at all, so it currently doesn't have any rules set that would cause it to reject anything. I made a DHCP reservation for my laptop's MAC address in my router to make sure I was always using the correct IP address. Please note that I am using a "command line only" install of Ubuntu, so I can't use any GUI network config tools. The reason I want to ping it is because I am trying to run an NFS server on the laptop, yet despite correctly setting it up I cannot access the NFS volume on another computer because it isn't even visible on the network right now.

  Read the article

• Script to setup ubuntu as a wireless accesspoint on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless accesspoint. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• Enabling DHCP without being connected

  - by Joe Philllips

  I was installing Ubuntu server the other night and I was not able to hook up to the network while installing because I don't have a monitor for my desktop machines. I had to go into the living room and connect to the HDTV instead. This leaves me without network connectivity. When installing it asks how I would like to set up the network. I would like to enable DHCP but it tries to detect a gateway when I do this and obviously it doesn't find anything. It won't let me move on without setting up an IP manually at that point. Isn't there a way I can enable DHCP for the next time it boots up instead? Why the need for it right then and there?

  Read the article

• When Ubuntu Server restarts eth0 Doesn't come back up

  - by JoelGsus

  Every time I restart my Ubuntu Server 11.10 I can't ssh into it because ETH0 doesn't come up automatically. I never had this problem before upgrading to 11.10. I have to login to the server and start the ETH0 manually. I would appreciate it any help. Thanks. Here is my /etc/networks/interfaces file: #The loopback network interface auto lo eth0 iface lo inet loopback # The primary network interface iface eth0 inet static address 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 gateway 192.168.1.1

  Read the article

• How to debug wifi connection?

  - by mmb

  I am using Ubuntu's Network Manager to connect to a local wifi router. My problem is, that it often disconnects without any visible reason (router is on, internet connection seems to be working, wifi diodes are blinking). I mostly have to disable wifi from Network Manager, enable it again to get wifi connecting again. Plus I am often experiencing Network Manager trying to connect to my wifi, trying several times but then giving up. I even tried an external usb-wifi card, but with the very same results. My question is: How can I debug this? Which logs should I read to see what is really happening when all of these errors occur - so I can post them here and see how to proceed?

  Read the article

• Query total page count via SNMP HP Laserjet

  - by Tim

  I was asked to get hold of the total pages counts for the 100+ printers we have at work. All of them are HP Laser or Business Jets of some description and the vast majority are connected via some form of HP JetDirect network card/switch. After many hours of typing in IP addresses and copying and pasting the relevant figure in to Excel I have now been asked to do this on a weekly basis. This led me to think there must be an easier way, as an IT professional I can surely work out some time saving method to solve this issue. Suffice it to say I do not feel very professional now after a day or so of trying to make SNMP work for me! From what I understand the first thing is to enable SNMP on the printer. Done. Next I would need something to query the SNMP bit. I decided to go open source and free and someone here recommended net-snmp as a decent tool (I would like to have just added the printers as nodes in SolarWinds but we are somewhat tight on licences apparently). Next I need the name of the MIB. For this I believe the HP-LASERJET-COMMON-MIB has the correct information in it. Downloaded this and added to net-snmp. Now I need the OID which I believe after much scouring is printed-media-simplex-count (we have no duplex printers, that we are interested in at least). Running the following command yields the following demoralising output: snmpget -v 2c -c public 10.168.5.1 HP-LASERJET-COMMON-MIB:.1.3.6.1.2.1.1.16.1.1.1 (the OID was derived from running: snmptranslate -IR -On printed-media-simplex-count Unlinked OID in HP-LASERJET-COMMON-MIB: hp ::= { enterprises 11 } Undefined identifier: enterprises near line 3 of C:/usr/share/snmp/mibs/HP-LASER JET-COMMON-MIB..txt .1.3.6.1.2.1.1.16.1.1.1 ) Unlinked OID in HP-LASERJET-COMMON-MIB: hp ::= { enterprises 11 } Undefined identifier: enterprises near line 3 of C:/usr/share/snmp/mibs/HP-LASER JET-COMMON-MIB..txt HP-LASERJET-COMMON-MIB:.1.3.6.1.2.1.1.16.1.1.1: Am I barking up the wrong tree completely with this? My aim was to script it all to output to a file for all the IP addresses of the printers and then plonk that in Excel for my lords and masters to digest at their leisure. I have a feeling I am using either the wrong MIB or the wrong OID from said MIB (or both). Does anyone have any pointers on this for me? Or should I give up and go back to navigationg each printers web page individually (hoping not).

  Read the article

• How is the "change password at next logon" requirement supposed to work with RDP using Network Level Authentication?

  - by NReilingh

  We have a Windows server (2008 R2) with the "Remote Desktop Services" feature installed and no Active Directory domain. Remote desktop is set up to "Allow connections only from computers running Remote Desktop with Network Level Authentication (more secure)". This means that before the remote screen is displayed, the connection is authenticated in a "Windows Security: Enter your credentials" window. The only two role services installed on this server is the RD Session Host and Licensing. When the "User must change password at next logon" checkbox is selected in the properties for a local user on this server, the following displays on a client computer after attempting to connect using the credentials that were last valid: On some other servers using RDP for admin access (but without the Remote Desktop Services role installed), the behavior is different -- the session begins and the user is given a change password prompt on the remote screen. What do I need to do to replicate this behavior on the Remote Desktop Services server?

  Read the article

• What is the crappiest network build you've ever seen?

  - by Ivan Petrushev

  This is only about networks you have seen personaly, not heared from others or seen on pictures at the web. Cables hanging from the ceiling lamps? Cables going trough culverts and other tubes? Switches and other equipment in the cleaner's closet? Cleaning lady's rags drying hanging from the cables? Key to the main node door possesed only by the janitor (or other non-tech and completely non-network-related guy)? Switches powered by foreign power adapters (cheaper and providing non-specified voltage or amperage)? All of this was in my old dormitory. Tell us about your bad experience.

  Read the article

• What is the best way to setup a public and private wireless access point on the same home network?

  - by Dougman

  For my home network (with internet provided from a cable modem) I would like to setup a secure wireless access point that I use for all of my personal connections (home PC, iPhone, Xbox, etc) and also another public access point that friends and folks in the neighborhood may connect to (for good karma). I want to ensure that my private traffic cannot be accessed from users of the public access point. I currently have one router that is running the Tomato firmware that I use with WPA security. What is the best way to accomplish this kind of setup securely (if it is possible in a home environment)?

  Read the article

• How to automatically enter username and password for network location in batch file?

  - by Phoenix Logan

  I have a batch file that copies files to a network location on WebDAV. The address looks something like this: \\xxxxxxxxx.net@SSL@2078\DavWWWRoot When I restart my computer, the batch file doesn't work and says "Access denied". Before a restart, it works, but it doesn't after the computer restarts. The problem is that it requires me to put in the username and password used to access the server. I have to browse to the server in File Explorer and sign in first. Even if I select the "Remember password" check box, it doesn't work. How can I get it to automatically sign in? I don't want to have to do this every time.

  Read the article

• How would you diagnose an integrated network card that doesn't show up on the device list?

  - by Tomer Gabel

  I've been setting up a server based around a Gigabyte GA-G33M-DS2R motherboard (G33, PCH9R with integrated Realtek 811B network device. I've enabled it in the BIOS, but it doesn't show up in the pre-boot PCI device list, isn't recognized by Windows (even after installing the chipset and networking drivers) and doesn't even show up via lspci. I've tried cycling power, disabling, cycling again, enabling, cycling again etc. to no avail. I'm sort of at a loss at this point; the board isn't under warranty anymore, but I'd rather not have to replace it. Any advice would be greatly appreciated...

  Read the article

• Is there a way to force Windows to recognize a network folder as a local drive, for the purposes of

  - by NoCatharsis

  I just started using the file search program Everything at work to search through documentation on our shared drives. This is after disappointments with Google Desktop and Windows Search. I love the speed of Everything, but I wish it were able to index other shared folders. My makeshift solution was to somehow force Windows to recognize the necessary shared folders as local drives, then add them to the index list. I have also considered using SyncToy, but this requires downloading all data to my drive, which could be terabytes of information - obviously not a good idea on a small company network. What would be the best solution here?

  Read the article

• changing permissions for a network share takes longer on win2008 than on win2003, why is that?

  - by HugoRune

  Given a network share accessible for "everyone" in the domain, containing several 1000 files and folders When I change permissions for this share from read/write to only read (or vice versa) on windows 2003, the change takes effect instantly. When I do the same on a share on Windows 2008, the dialog stays open for a long time before closing when I click on OK, and the server appears to be accessing a lot of files. What is the reason for this delay? Does Windows 2008 also change ntfs permissions for all files inside the share? If so, why doesn't win2003 have to do that? I do not mind the delay, after all I do not have to change this stuff very often, but I am curious. What are the differences between 2003 and 2008 in this regard?

  Read the article

• Can a mapped network drive be reconnected from the command line?

  - by Stephen Jennings

  On a daily basis I find myself in the Windows command prompt needing to access a network drive that is mapped but disconnected. I have yet to find a command that will reconnect this drive without unmapping and remapping (which leads to a password guessing game, since I don't own these computers). I would also like to be able to script this so every night the drive is reconnected if it has become disconnected somehow. The fastest solution I currently have is to: Type "start." to open explorer, Alt-D to focus the address bar, type the drive letter I want and press enter, and wait for it to display the drive contents, then finally, close explorer and go back to the command prompt. I know it's a minor inconvenience, but I'm often doing this through a slow VNC or PCAnywhere connection where doing anything through GUI is awful, so I'm just wondering if there's a better solution.

  Read the article

• Why my Network Connection Properties don't show UAC prompt & settings change everytime I connect?

  - by Manish Shrivastaw

  I can't set my network connection interface properties, UAC prompt doesn't appear anymore for only this adapter interface. I disable Netbios but each time I connect it changes back to default. Earlier I could set & forget easily as UAC prompt showed for this dialup 3G connection. It's very frustrating to change settings every time. Is there any way to make adapter interface 'blacklisted' (remove from UAC whitelist) again. I can manually make a connection (that shows Uac prompt) but my dialler app doesn't work with that. Is there any registry entry for setting privilege for Napagent etc. Or what could be the reason, please guide. All I want is to set my connection properties (Tcp advanced settings) which won't change.

  Read the article

• How do I get a rt2800usb wireless device working?

  - by Jii

  My brand new desktop running 13.04 has endless problems with wireless. Dozens of others are flooding forums with reports of the same problems. It worked fine for a few days, then there were a few days where it started having problems sometimes and working sometimes. Now it never works at all. I have 5+ devices all able to connect without any trouble at all, including iPhone, Android phone, 3DS, multiple game consoles, a laptop running windows 7, and even a second desktop machine running Ubuntu 12.04 sitting right behind the 13.04 machine. All other devices have full wireless bars displayed (strong signals). At any moment, one of the following is happening, and it changes randomly: Trying to connect forever, but never establishing a connection. Wireless icon constantly animating. Finds no wireless networks at all. (There are 12+ in range according to other devices.) Will not try to connect to the network. If I use the icon to connect, it will display "Disconnected" within a few seconds. Will continuously ask for the network password. Typing it in correctly does not help. Wireless is working fine. This happens sometimes. It can work for days at a time, or only 10 mins at a time. Various things that usually do nothing but sometimes fix the problem: Reboot. This has the best chance of helping, but it usually takes 5+ times. Disable/re-enable Wi-Fi using the wireless icon. Disable/re-enable Networking using the wireless icon. Use the icon to try and connect to a network (if found). Use the icon to open Edit Connections and delete my connection info, causing it to be recreated (once it's actually found again). Various things that seem to make no difference: Changing between using Linux headers in grub at bootup, between 3.10.0, 3.9.0, or 3.8.0. Move the wireless router very close to the desktop. Running sudo rfkill unblock all (I dunno what this is supposed to do.) I've used Ubuntu for 6 years and I've never had a problem with networking. Now I'm spending all my time reading through endless problem reports and trying all the answers. None of them have helped. I am doing this instead of getting work done, which is defeating the whole purpose of using Ubuntu. It's heartbreaking to be honest. In the current state of "no networks are showing up", here are outputs from the random things that other people are usually asked to run: lspic 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) lsmod Module Size Used by e100 41119 0 nls_iso8859_1 12713 1 parport_pc 28284 0 ppdev 17106 0 bnep 18258 2 rfcomm 47863 12 binfmt_misc 17540 1 arc4 12573 2 rt2800usb 27201 0 rt2x00usb 20857 1 rt2800usb rt2800lib 68029 1 rt2800usb rt2x00lib 55764 3 rt2x00usb,rt2800lib,rt2800usb coretemp 13596 0 mac80211 656164 3 rt2x00lib,rt2x00usb,rt2800lib kvm_intel 138733 0 kvm 452835 1 kvm_intel cfg80211 547224 2 mac80211,rt2x00lib crc_ccitt 12707 1 rt2800lib ghash_clmulni_intel 13259 0 aesni_intel 55449 0 usb_storage 61749 1 aes_x86_64 17131 1 aesni_intel joydev 17613 0 xts 12922 1 aesni_intel nouveau 1001310 3 snd_hda_codec_hdmi 37407 1 lrw 13294 1 aesni_intel gf128mul 14951 2 lrw,xts mxm_wmi 13021 1 nouveau snd_hda_codec_realtek 46511 1 ablk_helper 13597 1 aesni_intel wmi 19256 2 mxm_wmi,nouveau snd_hda_intel 44397 5 ttm 88251 1 nouveau drm_kms_helper 49082 1 nouveau drm 295908 5 ttm,drm_kms_helper,nouveau snd_hda_codec 190010 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel cryptd 20501 3 ghash_clmulni_intel,aesni_intel,ablk_helper snd_hwdep 13613 1 snd_hda_codec snd_pcm 102477 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel btusb 18291 0 snd_page_alloc 18798 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 i2c_algo_bit 13564 1 nouveau snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30417 1 snd_seq_midi snd_seq 61930 2 snd_seq_midi_event,snd_seq_midi bluetooth 251354 22 bnep,btusb,rfcomm snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi lpc_ich 17060 0 snd_timer 29989 2 snd_pcm,snd_seq mei 46588 0 snd 69533 20 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device psmouse 97838 0 microcode 22923 0 soundcore 12680 1 snd video 19467 1 nouveau mac_hid 13253 0 serio_raw 13215 0 lp 17799 0 parport 46562 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 47346 0 hid 101248 2 hid_generic,usbhid ahci 30063 3 libahci 32088 1 ahci e1000e 207005 0 ptp 18668 1 e1000e pps_core 14080 1 ptp sudo lshw -c network 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) sudo iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on sudo iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results NOTE: This dmesg was done after a reboot where the network manager was continuously displaying the "disconnected" message over and over. So it must have been trying to connect at this time. My network was displayed in the list of options, as the only option despite other devices picking up 12+ access points. The router channel is set to auto. dmesg | tail -30 [ 187.418446] wlan0: associated [ 190.405601] wlan0: disassociated from 00:14:d1:a8:c3:44 (Reason: 15) [ 190.443312] cfg80211: Calling CRDA to update world regulatory domain [ 190.443431] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 190.451635] cfg80211: World regulatory domain updated: [ 190.451643] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 190.451648] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451652] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451656] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451659] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451662] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 191.824451] wlan0: authenticate with 00:14:d1:a8:c3:44 [ 191.850608] wlan0: send auth to 00:14:d1:a8:c3:44 (try 1/3) [ 191.884604] wlan0: send auth to 00:14:d1:a8:c3:44 (try 2/3) [ 191.886309] wlan0: authenticated [ 191.886579] rt2800usb 3-5.3:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 191.886588] rt2800usb 3-5.3:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 191.889556] wlan0: associate with 00:14:d1:a8:c3:44 (try 1/3) [ 192.001493] wlan0: associate with 00:14:d1:a8:c3:44 (try 2/3) [ 192.040274] wlan0: RX AssocResp from 00:14:d1:a8:c3:44 (capab=0x431 status=0 aid=3) [ 192.044235] wlan0: associated [ 193.948188] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 193.981501] cfg80211: Calling CRDA to update world regulatory domain [ 193.984080] cfg80211: World regulatory domain updated: [ 193.984082] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 193.984084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984086] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984087] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) The router uses MAC filtering, and security is WPA PSK with cipher as auto. So, any ideas? Or is the solution just to not use 13.04 unless you have a wired connection? (I don't have this option.) If so, please just tell me straight. I survived 9.04 Jaunty, and I can survive 13.04 Raring. Update #1 Results from trying Wild Man's first answer: jii@conan:~$ echo "options rt2800usb nohwcrypt=y" | sudo tee /etc/modprobe.d/rt2800usb.conf options rt2800usb nohwcrypt=y jii@conan:~$ sudo modprobe -rfv rt2800usb rmmod rt2800usb rmmod rt2800lib rmmod crc_ccitt rmmod rt2x00usb rmmod rt2x00lib rmmod mac80211 rmmod cfg80211 jii@conan:~$ sudo modprobe -v rt2800usb insmod /lib/modules/3.10.0-031000-generic/kernel/lib/crc-ccitt.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00usb.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko nohwcrypt=y I tried: gksudo gedit /etc/pm/power.d/wireless but I didn't have the package. It said to install gksu. I tried that, but of course, not having Internet, I didn't get the package. So instead I did: sudo gedit /etc/pm/power.d/wireless Which created the file. Here is the body: #!/bin/sh /sbin/iwconfig wlan0 power off I then rebooted. No change. I tried adding exit 0 to the bottom of the wireless file, and rebooted. No change. Please note that this is a desktop machine. I'm assuming power management is primarily for laptops, but the iwconfig does state that power management is on, so who knows. The recommended router changes I did not do, since the current router settings are (I think) required for some of the older devices I have, and because the current settings work on all my modern devices including Ubuntu 12.04 and Windows 7. I do appreciate the advice though, and I'll look into it when I have time. Anything else to try? Update #2 I booted into Ubuntu 12.04.3 from a dvd, and the same problems exist. I have a separate old desktop machine with 12.04 installed that has no wireless problems at all. So obviously the problem is wireless hardware compatibility in both 12.04.03 LTS and 13.04. Update #3 The same problems exist even when using a wired connection. I plugged an ethernet cable directly to the router and the network manager added an "Auto Ethernet" entry, but it cannot establish a connection to it. So the problem is not specific to wireless. Meanwhile, I purchased a Trendnet N300 wireless USB adapter, TEW-664UB. I plugged it in, but I have no idea how to get Ubuntu to try and use it. Can anyone tell me how? Can I download a package on another computer and copy the .deb over to do an install, etc? I'm installing windows 7 to double check that the internet connection works there and it's not just some magically faulty hardware. Thanks for your help.

  Read the article

• Share the same subnet between Internal network and VPN Clients

  - by Pascal

  I would like to set up a configuration where VPN clients connecting to my Forefront TMG can access all the resources of my Internal network without having the to use the option "Use default gateway on remote network" on the VPN's TCP/IP Ipv4 Advanced Settings. This is important to me, since they can use their own internet while accessing my network through VPN (the security implications of this are acceptable on my cenario) My Internal network runs on 10.50.75.x, and I set up Forefront TMG to relay the DHCP of my Internal network to the VPN clients, so they get IPs from the same range as the Internal network. This setup initially works, and the VPN clients use their own internet, and can access anything that is on the internal network. However, after a while, HTTP Proxy Traffic from the Internal network starts getting routed to the IP of the RRAS Dial In Interface, instead of the IP of the Internal's network gateway. When this happens, the HTTP Proxy starts getting denied for obvious reasons. My first question is: does this happen because Forefront TMG wasn't designed to handle a cenario that I described above, and it "loses itself"? My second question is: Is there any way to solve this problem, either through configuration or firewall policies? My third question is: If there's no way that it can work with the cenario above, is there another cenario that will solve my problem, and do what I'd like it to do properly? Below are my network routes: 1 => Local Host Access => Route => Local Host => All Networks 2 => VPN Clients to Internal Network => Route => VPN Clients => Internal 3 => Internet Access => NAT => Internal, Perimeter, VPN Clients => External 4 => Internal to Perimeter => Route => Internal, VPN Clients => Perimeter Tks!

  Read the article

• Application losing Printer within Terminal Services for remote users

  - by Richard

  Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

  Read the article

• Problem setting up HP PhotoSmart C4783

  - by ProfKaos

  I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

  Read the article

• Are there cloud network drives that let users lock files or mark them as "in use"?

  - by Brandon Craig Rhodes

  Having spent several hours reading about the features and limitations of services like DropBox and Jungle Disk and the hundreds of competitors they seem to have (as though everyone with an AWS account these days goes ahead and writes a file sharing application just for fun), I have yet to find one that would let a team of people at a small business collaborate without stepping all over each other's toes. At a small business there are often many small documents per project — estimates, contracts, project plans, budgets — and team members frequently have to open and edit them, with all sorts of problems happening if two people edit a file at once. Even if a sharing service is smart enough to keep both versions of the file created, most small-business software (like word processors, spreadsheets, estimating software, or billing systems) has no way to compare — much less to merge! — the changes in two rival versions of a file that two people edited at the same time without each other's knowledge. So, my question: are their cloud-based file sharing solutions that not only provide a virtual network drive that people can access, but that also let users lock files — even if it's not a real lock but just a flag or indicator — that could possibly prevent remote workers from both editing the same file at once? Having one person wait for another person to finish editing is a very, very small inconvenience compared to the hour or more than it can take to compare two estimates by hand until you find and resolve the rival changes. Given this fact, I am surprised that almost none of the popular file sharing solutions seem to recognize this problem and provide some solution! Does anyone know of a service that does?

  Read the article

• Are there cloud network drives that let users lock files or mark them as "in use"?

  - by Brandon Craig Rhodes

  Having spent several hours reading about the features and limitations of services like DropBox and Jungle Disk and the hundreds of competitors they seem to have (as though everyone with an AWS account these days goes ahead and writes a file sharing application just for fun), I have yet to find one that would let a team of people at a small business collaborate without stepping all over each other's toes. At a small business there are often many small documents per project — estimates, contracts, project plans, budgets — and team members frequently have to open and edit them, with all sorts of problems happening if two people edit a file at once. Even if a sharing service is smart enough to keep both versions of the file created, most small-business software (like word processors, spreadsheets, estimating software, or billing systems) has no way to compare — much less to merge! — the changes in two rival versions of a file that two people edited at the same time without each other's knowledge. So, my question: are their cloud-based file sharing solutions that not only provide a virtual network drive that people can access, but that also let users lock files — even if it's not a real lock but just a flag or indicator — that could possibly prevent remote workers from both editing the same file at once? Having one person wait for another person to finish editing is a very, very small inconvenience compared to the hour or more than it can take to compare two estimates by hand until you find and resolve the rival changes. Given this fact, I am surprised that almost none of the popular file sharing solutions seem to recognize this problem and provide some solution! Does anyone know of a service that does?

  Read the article

• How to forceably unmount stuck network share in Mac OS X?

  - by Kyle Lowry

  Not long ago my Xserve failed (power loss) while an iMac was working with files on a particular network share (called "Work Share"). This volume, "Work Share", is now stuck. It can't be seen in the GUI, you can only detect it using the Terminal. Even after power cycling over the course of several days, ls -a still shows that it's there, but I can't unmount it using any command - not even as root in single user mode. Every time I attempt to unmount that volume, I get the message that the resource is busy (which it can't possibly be since nothing is using it), and error code 4915. The issue is that when I mount the real "Work Share", it internally is renamed to "Work Share-1", which breaks all my links, and several files in the share. If I can't unmount the false "Work Share", then that computer would be unuseable without a reformat, I would imagine - and I don't want it to have to come to that. I've tried everything I can think of - it looks like sudo can't save me now. Any ideas on how to unmount this stuck volume?

  Read the article

• Recommendations for a JetDirect print server for USB 2.0 printers?

  - by eleven81

  I have been using some older HP JetDirect 300x print servers for a variety of parallel printers over the years. These things work great for every printer I have tried them with, including HP's, Dell's, and even a Mountbatten braille embosser! These have been a boon for printers whose internal network cards fail, but whose parallel ports continue working. I don't have to throw away the $500 printer that is one year and a week old, and can keep using it for many, many years. Now that very few printers are coming with parallel ports, but are coming solely with USB connections and network cards. When the network card fails but the printer is still usable, I want to continue using it on the network with a JetDirect card. In summary: Does anyone have any recommendations for JetDirect cards that will work as well with USB 2.0 printers of unspecified manufacturer that my old JetDirect 300x cards do?

  Read the article

• Guest can't access host windows network share

  - by Asteroza

  HI folks, I've recently run into a strange problem after upgrading to VMware player 3. Certain virtual machines (currently an XP and a VIsta VM) seem to have lost the ability to access the host (XP) network shared folders (SMB). Both VM machines are bridged networking, firewall is up. Host firewall is up. Host and guests use DHCP. All OS are workgroup connected. The Vista VM I am not completely sure, but the XP VM did have access to the host's network shared folders after the player upgrade. Then today it wouldn't work, network path can't be found. Now here's the wierd part. The host's network shared folders can be accessed properly by other PC's on the network (and as far as I know, no settings have been changed). The host is pingable from the guests, and name resolution works. The guests can access network shares on other PC's in the network, and access the internet. My Network Places shows the host PC, but double clicking on it takes a long time before it finally times out with an error. Doing a wireshark packet capture, the guest is sending out the protocol negotiation, and the host is sending a response, but after that the guest behaves like it didn't receive anything and is doing TCP retransmissions. Anybody have any idea what could be wrong? Yes I know I can drag and drop files or setup the special VMware shared folders, but I want to access the host just like any other network accessible shared folder. It just seems really odd when any other computer works, just not between the guest and host.

  Read the article

• Connect to WEP Wireless Network by command line on Ubuntu

  - by Tim

  Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

  Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >