Search Results

Search found 5530 results on 222 pages for 'wifi direct'.

Page 38/222 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

• Link rate between EMC DAE and HBA

  - by Johan Christensson

  I have a EMC DAE (KTN-STL4) drive cage directly connecconnected to a HP Proliant server using a QLogic QLE2560 HBA. I'm using copper cable between the HBA card and the DAE. On the controller card in the DAE there is a label that states "4Gb". I'm guessing that this means 4Gbit/s. But if I set the HBA card to "Auto speed" it negotiate 2Gbit/s, and if I hard set it to 4Gbit/s I end up with no link. Why is this? Isn't the DAE controller card capebel of link speed higher then 2Gbit/s or is it the copper cable that limits the speed, or is it the interface used between the DAE and Qlogic HBA that is the problem? I have been browsing for HSSDC-FC converters and they always seems to på rated at ~2Gbit/s. If this is the limit, why does it say 4Gb on the controller cards in the DAE?

  Read the article

• RDP access to DirectAccess Server via DirectAccess

  - by crgnz

  I have just setup a Win2008R2 DirectAccess server (and also a Win2008R2 Active Directory server). From the Internet I can Remote Desktop login to the AD server, but I cannot RDP into the DirectAccess server. I can PING both servers and get an IPv6 response. (I can RDP to the DirectAccess server from the internal company network) DirectAccess is configured to allow full intranet access. I think I've hit a mental block, the answer will probably be obvious, but I just can't see it.

  Read the article

• How do i use a USB wifi device properly?

  - by acidzombie24

  I'll just say a few random things One usb wifi device i notice only worked when it plugged into my usb hub Another one worked but couldnt get full speed. It came with an extention cord and when i had it a few feet away i was able to (usually) get full speed I had a wifi card in a tower in the past and just about all laptops have it built in How do i use a USB wifi adapter properly? The first device didnt come with an extention cord and made no mention of bringing it away from the computer. When someone else tested the device he said he was getting full speed while it was plugged into his tower so i was pretty surpised. How do i use USB wifi devices properly?

  Read the article

• cannot send emails to other Web servers

  - by developer

  I'm trying to limit my server's open ports in CSF. The IPv4 port settings include: # Allow incoming TCP ports TCP_IN = "22,25,53,80,110,143,443,587,3654,53343” # Allow outgoing TCP ports TCP_OUT = "22,53,80,113,443,465,995,3654" # Allow incoming UDP ports UDP_IN = "53" # Allow outgoing UDP ports # To allow outgoing traceroute add 33434:33523 to this list UDP_OUT = "53,113,123" As you see, I have port 25 open in TCP_IN but have removed it from TCP_OUT. The reason is I wanted to have my mails transmitted over smtps, so I have port 465 opened instead in TCP_OUT. Since I am using Rouncube in Directpanel, I have also set the following in Rouncube's config.inc.php: $config['default_host'] = 'ssl://mail.mydomain.com'; $config['smtp_server'] = 'ssl://mail.mydomain.com'; $config['smtp_port'] = 465; However, when I remove port 25 from TCP_OUT, I no longer can send mails, say, to gmail, though I can send mails to own. But I can receive all mails. Please let me know if I need to make any further changes. Do I need to disable port 25 at all, to have my mails sent via ssl. Thanks

  Read the article

• ClamD server Currently Down

  - by RedLEON

  I'm getting this error message after install ClamAV from direcadmin message system. OS: CentOs 5. The service 'clamd' on server star.tunahost.net is currently down This message has been automatically generated notifying you that the service clamd is currently down. Why can I get this error for each hour? I checked up cron jobs and I couldn't find any job about it. How to control Clamd service? OS: CentOS with DirectAdmin

  Read the article

• dnssec zonesigner ignoring out-of-zone data

  - by jordi12100

  I am trying to configure DNSSec with BIND9 on CentOS 6.4 running DirectAdmin control panel. I am using this tutorial to make it work: https://www.dnssec-tools.org/wiki/index.php/Zonesigner But I can't get it work... When I run this command: zonesigner --genkeys jordikroon.nl.db jordikroon.nl.db.signed I get this error: jordikroon.nl.db:17: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:18: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:22: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:29: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:33: ignoring out-of-zone data (jordikroon.nl) zone jordikroon.nl.db/IN: has no NS records zone jordikroon.nl.db/IN: not loaded due to errors. I can't find anything on the web about this error. This is my zone db file: $TTL 14400 @ IN SOA ns1.ghservers.org. hostmaster.jordikroon.nl. ( 2013090703 14400 3600 1209600 86400 ) jordikroon.nl. 14400 IN NS ns1.ghservers.org. jordikroon.nl. 14400 IN NS ns2.ghservers.org. cp 14400 IN A 85.17.32.228 ftp 14400 IN A 85.17.32.228 jordikroon.nl. 14400 IN A 85.17.32.228 localhost 14400 IN A 127.0.0.1 mail 14400 IN A 85.17.32.228 pop 14400 IN A 85.17.32.228 smtp 14400 IN A 85.17.32.228 www 14400 IN A 85.17.32.228 jordikroon.nl. 14400 IN MX 10 mail jordikroon.nl. 14400 IN TXT "v=spf1 a mx ip4:85.17.32.228 ~all" localhost 14400 IN AAAA ::1 How do I have to fix this? All IN keywords are being ignored. Any help is welcome:-)

  Read the article

• ProFTPD mod_tls is not loaded properly?

  - by develroot

  The server is running CentOS 5 with DirectAdmin. I am trying to get ProfFTPD work over TLS, however it seems that proftpd is lacking mod_tls support, even though it was compiled with mod_tls. # proftpd -l Compiled-in modules: mod_core.c mod_xfer.c mod_auth_unix.c mod_auth_file.c mod_auth.c mod_ls.c mod_log.c mod_site.c mod_delay.c mod_facts.c mod_ident.c mod_ratio.c mod_readme.c mod_cap.c As you can see there is no mod_tls.c, however, the DirectAdmin configuration file for proftpd suggests that it was built with TLS support: # cat /usr/local/directadmin/custombuild/configure/proftpd/configure.proftpd #!/bin/sh install_user=ftp \ install_group=ftp \ ./configure \ --prefix=/usr \ --sysconfdir=/etc \ --localstatedir=/var/run \ --mandir=/usr/share/man \ --without-pam \ --disable-auth-pam \ --enable-nls \ --with-modules=mod_ratio:mod_readme:mod_tls And all I get when I try to connect over FTPS using FileZilla is: Raspuns: 220 ProFTPD 1.3.3c Server ready. Comanda: AUTH TLS Raspuns: 500 AUTH not understood Comanda: AUTH SSL Raspuns: 500 AUTH not understood Am I missing something? thanks.

  Read the article

• Migrating email forwarding entries from DirectAdmin to Google App (Free edition)

  - by bobo

  I have a website hosted in a shared hosting account and it contains a DirectAdmin (DA) control panel. From there, I can see some email forwarding entries. I would like to migrate the email server to the Google App's, I am going to change the MX records to point to Google email server in the DA. For the existing email accounts that I see in the DA, I will re-create them in the Google App. But for those email forwarding entries, I am confused. If I keep them there, will they still work after I have changed the MX record pointing to the Google email server? If not, this means I will need to re-create them in the Google App, right? Unfortunately, Google App (Free edition) does not seem to allow email forwarding like those in DA. Unless I choose to use other editons (http://www.google.com/support/a/bin/answer.py?answer=175745). In DA, when I have created an email forwarding entry such as [email protected] - [email protected], I do not really need to create a dummy [email protected] email account and DA will still do the forwarding properly. The best I can do now, without upgrading the Google App edition, is to simply create dummy email accounts in the Google App and setup forwarding inside that email account, is this correct?

  Read the article

• Is possible to boot on PXE over a WiFi device?

  - by Diogo Rocha

  As I know it is possible to boot up some bootable images (like Linux, Clonezilla, management applications and others) over a PXE (Preboot Execution Environment) server with an Ethernet device (802.3). Can the same thing be done with an Ethernet WiFi (802.11) device? I tested with my notebook but my BIOS appears to not enable booting from WiFi devices. Is it possible with some specific WiFi cards and/or a specific BIOS?

  Read the article

• Add IPv6 support to DirectAdmin server

  - by George Boot

  I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

  Read the article

• Domain names timing out after VPS IP change

  - by Fourjays

  I rent a CentOS 5 VPS from a UK-based provider, with DirectAdmin also installed. On Thursday night, they carried out planned maintenance to changed the two IPs I had been assigned to two new ones. On Friday, after the change had taken place, I updated my domain name records to reflect the IP change. Since then, all of the domains pointing to the VPS are timing out. Additionally, DirectAdmin was also not responding, but was was resolved by running the ipswap scripts as found in the DirectAdmin knowledgebase. It did not fix my domains though. I have contacted the VPS provider but I have been waiting for a response for some time now. I have checked again, and again, and all the IPs referenced in DirectAdmin are correct. If I go to the server IP in my browser it responds with "Apache is functioning normally." Email accounts on the server are also functioning correctly. But if I access a domain itself, it times out. Running a ping and a DNS look-up, I can confirm the nameserver IPs are correct. If I run a trace route it reaches an IP that is similar to my VPS IPs (last 2 blocks are different) before timing out (it never shows my server IP). I am relatively new to VPS management so don't have a vast wealth of experience with troubleshooting problems on them. I have checked all of the httpd configuration files, which don't seem to have any IP references in them at all. Looking in the Apache error logs, what errors there are do not coincide with times I have tried to access the site. Is this issue at my provider's end? Is there anything else I can check or test, to rule out post-IP-change problems with my server configuration? It was all running fine prior to the IP change.

  Read the article

• Changing SPF (Sender Policy Framework) record for Google Apps

  - by bobo

  My boss asked me to set up Google Apps for a client and basically I have done everything including setting up MX records in DirectAdmin and re-creating the email accounts in Google Apps. I also sent a few test emails to ensure that it actually works and it seems fine. But then I discovered this article talking about changing the SPF record for the domain. http://www.google.com/support/a/bin/answer.py?answer=178723 After reading the introduction I think it would be better for me to change the SPF record according to this article. So I logged in to the DirectAdmin and navigated to the DNS management, and then I found that there's already a TXT SPF record there: v=spf1 a mx a:spf.cabin.com.hk include:gmail.com -all And it looks like it's already including gmail.com, but according to the article it should be: _spf.google.com rather than: gmail.com I dare not to change it before I understand what this record actually means. What would you do with this record if you were me?

  Read the article

• In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

  - by Bobby Burgess

  This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• Sudden problems with iptables not running

  - by Fourjays

  I've got a sudden issue with iptables not running on my CentOS 5.8/DirectAdmin XenVPS. All I have done today is install PHP APC and run an update (although I admittedly didn't pay much attention today - I usually do). Iptables has been running fairly smoothly since I installed it over 6 months ago. Basically when I try to run iptables -L it tells me: iptables v1.3.5: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. I've looked around and tried a few things and it appears that maybe my kernel doesn't have the modules loaded? I've been reading this and tried the two commands they suggest to no avail. Except there does appear to be a mismatch on one bit of output: -bash-3.2# cd /lib/modules -bash-3.2# ls 2.6.18-194.32.1.el5xen 2.6.18-238.5.1.el5xen 2.6.18-274.7.1.el5xen 2.6.39.1-cs-domU 2.6.18-238.12.1.el5xen 2.6.18-238.9.1.el5xen 2.6.37.2-cs-domU 3.0.1-cs-domU -bash-3.2# depmod -a WARNING: Couldn't open directory /lib/modules/2.6.18-274.18.1.el5xen: No such file or directory FATAL: Could not open /lib/modules/2.6.18-274.18.1.el5xen/modules.dep.temp for writing: No such file or directory Does this mean the versions are out of sync? If so, what are my next steps to getting this fixed? As you can probably tell I am still learning how to manage my server so please be very clear in all advice. Many thanks :)

  Read the article

• Is Joerg Schilling's "sdd" a full replacement for "dd"

  - by fishtoprecords

  I'm trying to use 'sdd' on my Debian system, and can't get one set of options to work. They do work in 'dd' so I am wondering if I am specifying them incorrectly, or if sdd didn't implement them, or something else. What I want to do is sdd if=/dev/hdh1 of=/bay5/imagebay1 bs=4096 conv=sync,noerror if I leave out the "conv=..." option, it works, or at least starts copying data. sdd if=/dev/hdh1 of=/bay5/imagebay1 bs=4096 Can you shed a bit of light?

  Read the article

• Two SSL certs for a domain in DirectAdmin

  - by Bart van Heukelom

  If I were to get 2 SSL certificates, one for example.com and one for www.example.com, is there a way to install them both on the site example.com in DirectAdmin? The default interface only allows installing one for both versions. If not, can I separate the 2 domains into 2 sites? One of them would only be a redirection, so there wouldn't be any duplication of site files. (Please don't answer with "one certificate should work for both". It doesn't always. This is a DirectAdmin question)

  Read the article

• how can i get list of created and deleted files on the server?

  - by max

  i have a image sharing website , users log and upload image last night i've lost about 30 newly-consecutive uploaded images ... i mean they have been uploaded ... apparently ... they are in the database but the actual image on the server is gone ! error log doesn't show anything ... so i thought my best option is to check list of created and deleted files ... if there is any ! is there a log file for created and deleted files on the server ? i'm using directadmin

  Read the article

• Fresh install CentOS 6.4 64b with directadmin slowly consumes all memory and crashes

  - by Coen Ponsen

  Dear server fault community, This is my first question on server fault, i'm new to server (mis)configuration so please forgive me for asking something stupid :) I'm running Directadmin on a CentOS 6.4 64b with 4GB memory and over 10000Gh virtual machine. I migrated my websites because my former vps couldn't keep up anymore. Only half of the websites from this 1GB machine were migrated jet. So the migration is still in progress and already my server crashes every day. The server performance up until that moment is perfect. The directadmin log files show nothing out of the ordinary. Yesterday only the mysql server crashed but it also crashed the entire machine before. The memory usage in DA seems to be normal: directadmin directadmin (pid 3923 22158 22159 22160 22161 22162 )8.75 MB dovecot dovecot (pid 3851 ) 47.8 MB exim exim (pid 1350 ) 1.29 MB httpd (pid 21525 21528 21529 21530 21531 21532 21546 21571 21742 21743 21744 )490.4 MB mysqld mysqld (pid 1299 ) 287.8 MB named named (pid 3807 ) 16.3 MB proftpd proftpd (pid 1481 ) 1.91 MB sshd sshd (pid 1173 21494 ) 5.16 MB Restarting services immediately frees up memory, but slowly over time the memory usage increases(about 24 hours to crash). The commands: # sync # echo 3 > /proc/sys/vm/drop_caches Will free al memory correct. I could just create a cronjob but it seems the wrong way around to me. I can't seem to pinpoint the cause. Any advices, references or tips are highly appreciated! Greetings, Coen edit: free -m : after drop_caches: total used free shared buffers cached Mem: 3830 735 3095 0 0 21 -/+ buffers/cache: 712 3117 Swap: 991 0 991 I'll post another one this evening.

  Read the article

• DirectAdmin Centos4 server has virus

  - by Rogier21

  Hello all, I have a problem with a webserver that runs Centos4 with DirectAdmin. Since a few weeks some websites hosted on it are not redirecting on search engines properly, they are redirected to some malware site, resulting in a ban from google. Now I have used 3 virusscanners: ClamAV: Didn't find anything Bitdefender: Found a 2-3 files with JS infection, deleted them AVG: Finds lots of files, but doesn't have the option to clean! The virus that it finds is: JS/Redir JS/Dropper Still the strange thing is: website a (www.aa.com) does not have any infected files (have gone through all the files manually, is a custom PHP app, nothing special) but does still have the same virus. Website b (www.bb.com) does have the infected files as only one. I deleted all these files and suspended the account, but no luck, still the same error. I do get the log entries on the website from the searchengines so the DNS entries are not changed. But now I have gone through the httpd files but cannot find anything. Where can I start looking for this?

  Read the article

• How to interconnect laptop, PC, Android & Symbiam phones with WiFi?

  - by noquery

  What I have Level One wifi Router hub Laptop with Windows 7 (wifi enabled) Desktop PC with Windows 7 (with no wifi, maybe LAN cables can help) 2 android & 1 Symbian Phones each wifi enabled. LAN Cables Hathway Internet connection which allows only 1 login to access internet What I want Is it possible to access internet on PC, laptop, mobiles at the same time with only one connection? Since I don't know even A of networking so please suggest some software which require minimum cofiguration. Let me know if any other hardware I require.

  Read the article

• I would like to send the wifi wep key automaticaly to laptops on the lan via powershell

  - by clide

  How do I send the wifi wep key automaticaly to laptops on the lan via powershell

  Read the article

• Making a bash script that reconnect to AP when connection lost

  - by Alexander

  I'm facing problems with WIFI on ubuntu i tried to update the system but still the same what happens is that i suddenly lose the connection with my router and when i press on the WIFI bar the system won't detect any APs i have to uncheck "enable WIFI" option ,then re check it so it work,it automatically reconnect. I'm thinking of making a bash script that detects when the pc is disconnected from the router for any reason, and when it is disconnected it disable then enable the wifi. i mean like automating resetting the connection that possible ? i guess i must use this nmcli nm wifi off nmcli nm wifi on but how can i make the script know if the PC is disconnected from the WIFI ?

  Read the article

• navigator.onLine still true when turning off WiFi, false when set "work offline" in browser

  - by chimerical

  navigator.onLine is still returning true when I turn off Wi-Fi (Airport on my notebook in OS X). This is counterintuitive behavior. But when I set "work offline" in a browser like Firefox, it correctly returns false. Is this expected? alert(navigator.onLine ? "online" : "offline");

  Read the article

• Do I need a wifi card to have internet access?

  - by Sarah

  I am attempting to set up a wireless network on 11.04, freshly download today. The router is on and working. However, I do not have a wifi "card" (which I am assuming is a little USB-type thing that allows internet access, but correct me if I am wrong) and every time I try to type in the MAC address and everything, nothing works. I also get the "firmware missing" error when I scroll over the signal strength, which I have tried looking up but have been unsuccessful with completely understanding it. I guess my main question is do I need another little device to be able to use wifi on my ubuntu? I do have an ethernet cable but another person is using it and I do not want to be tied down to that cable. the problem is that none of the wireless networks show up, however they show up when I go into Windows mode on my laptop. I get an error message at the top saying "firmware missing" which I have tried looking up but still have no straight answer for.

  Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >