Search Results

Search found 5373 results on 215 pages for 'wireless bridge'.

Page 38/215 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

  • Wireless Internet Connection Sharing in Ubuntu

    - by klutch2
    As the title states, I need to share a wireless connection with a laptop running Ubuntu as the AP. The setup will be as follows: Corporate WiFi <<== Laptop <<== Other Devices i.e. (iPad, iPhone) I want to be able to connect the "Other Devices" via WiFi to the laptop. I have thought of setting up an ad-hoc network by connecting to the Corporate WiFi and then setting up a new network and hoping the connection to both would stay, but that doesn't seem to work. If I set up the ad-hoc network by itself, I can see it from my "Other Devices". The reason I need this is because for some reason, my iPad and my iPhone will not connect to my corporate WiFi and I need to use them so I want to use my laptop to share the connection and act as an AP for my "Other Devices". My laptop is a Chrome CR-48 running Ubuntu and as some of you might know, it does not have an ethernet port, so having a wired connecting and then setting up a network is out of question. I want to connect to the Corporate WiFi and share that connection by having the laptop act as an AP for other devices.

    Read the article

  • Wireless connection silently dies randomly

    - by Force Flow
    I have two WAP4410N wireless access points powered using Power-Over-Ethernet. They are both connected to the same LAN and broadcasting the same SSID with a WPA2 password. One is using channel 1, while the other is using channel 11. There is coverage overlap where the signal from both access points hover around -75db to -85db while standing in the same physical location. DHCP is disabled, and is being provided by another network device. Every day or so, devices can connect and authenticate to the access points, but are not granted an IP address (and subsequently are unable access to the LAN or Internet). For devices that had already retrieved an IP address prior to the issue exhibiting itself, the devices simply stop communicating with LAN and Internet. However, I can still access each access point's web admin interface from the LAN. If I reboot both devices, the problem vanishes and devices are once again able to get an IP address and connect to the LAN and Internet. Are these symptoms of signal interference between the two WAPs or is this a completely different issue?

    Read the article

  • My internet drops and will only reconnect if I troubleshoot it or restart my computer.

    - by Paul
    My internet loses its connection and at the same time, and my speaker seems broken if that happens and my mouse will not be smooth as it was before it happens. It already happened before and I didnt mind it. But now, it's happening literally all the time. After startup, my connection seems okay but after some few minutes, even without me doing something, my laptop will just lose its connection. It says that it is not connected and connections are available, but if I check if there are connections where I can connect it shows nothing. Even if, there is actually a wi-fi connection where my phone and other laptops connect. They dont seem to have problem with it. Just my laptop. After that happens, I usually restart my laptop but I discovered that troubleshooting it would somehow repair the problem, but not all the time. It says that restarting my wireless adapter do the job. Are there any long term fix? I mean that could last long or totally erase the problem? I have Atheros AR5B97 Wireless Network Adapter and Microsoft Virtual WiFi Miniport Adapter, both enabled. On the services, I have Wired AutoConfig and WLAN AutoConfig on Automatic. Aspire 4750, Windows 7 (x86)

    Read the article

  • Alfa AWUSO36H 1W dysfunctional driver

    - by BrainStorm
    I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

    Read the article

  • Access node.js local server though mobile via same shared wifi

    - by laggingreflex
    EDIT: I was stuck in this situation before but then it was Apache-related But this time I'm using NodeJS, so the old answer doesn't help. I'm running apache a NodeJS webserver (on port 80) on Windows 7. I want to access the webserver through my mobile which shares the wifi router with my pc locally. http://localhost works from PC. But I can't access http://192.168.1.4 from either my phone or even my computer. ipconfig /all on my computer lists my ip address as 192.168.1.4 Wireless LAN adapter Wireless Network Connection: IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred) I can ping my phone's (internal) ip address [192.168.1.5] from PC and vice-versa, I can ping my PC [192.168.1.4] from my phone. So why can't I access http://192.168.1.4 from my phone? (or PC) Firewall is off.

    Read the article

  • Ubuntu and Belkin N150 f6d4050 Wireless USB adapter v2

    - by Andrew
    I'm new to Ubuntu, and I'm trying to get my Belkin USB adapter to work. There are plenty of discussions out there already about this, but none really helped me out. Here's what I've done - Installed ndiswrapper Installed ndisgtk Installed the driver (rt2870.inf) via ndisgtk ndisgtk reported that the driver was installed and the hardware was present. The green light on the adapter is solid green, which I assume means that Ubuntu is aware of it's presence. However, when I click the little wireless symbol at the navigation bar, there's no option to choose my adapter (assuming that it's supposed to show up there...) My adapter version is F6D4050 - Where do I go from here? I'm a Ubuntu newb, so speak slowly. :P lsusb - andrew@ubuntu:~$ lsusb Bus 002 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 002 Device 002: ID 04f9:0229 Brother Industries, Ltd Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 050d:935b Belkin Components Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsmod - andrew@ubuntu:~$ lsmod Module Size Used by binfmt_misc 7960 1 fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit vga16fb 12757 0 vgastate 9857 1 vga16fb snd_cmipci 37557 2 snd_intel8x0 31155 2 snd_ac97_codec 125394 1 snd_intel8x0 ac97_bus 1450 1 snd_ac97_codec snd_mpu401 6875 0 snd_pcm_oss 41394 0 snd_mixer_oss 16299 1 snd_pcm_oss snd_pcm 87882 4 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_opl3_lib 10846 1 snd_cmipci snd_hwdep 6924 1 snd_opl3_lib snd_mpu401_uart 6857 2 snd_cmipci,snd_mpu401 snd_seq_dummy 1782 0 snd_seq_oss 31219 0 snd_seq_midi 5829 0 snd_rawmidi 23420 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event nouveau 515227 2 ttm 60847 1 nouveau snd_timer 23649 3 snd_pcm,snd_opl3_lib,snd_seq snd_seq_device 6888 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq ns558 3704 0 ppdev 6375 0 drm_kms_helper 30742 1 nouveau joydev 11072 0 ndiswrapper 244768 0 gameport 10966 3 snd_cmipci,ns558 usblp 12407 0 asus_atk0110 10033 0 parport_pc 29958 1 serio_raw 4918 0 drm 199204 4 nouveau,ttm,drm_kms_helper i2c_algo_bit 6024 1 nouveau edac_core 45423 0 edac_mce_amd 9278 0 k8temp 3912 0 snd 71106 23 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_mpu401,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_u art,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 8052 1 snd snd_page_alloc 8500 2 snd_intel8x0,snd_pcm i2c_nforce2 6099 0 lp 9336 0 parport 37160 3 ppdev,parport_pc,lp hid_logitech 8820 0 ff_memless 5109 1 hid_logitech ohci1394 30260 0 usbhid 41084 1 hid_logitech hid 83440 2 hid_logitech,usbhid usb_storage 49833 0 skge 41049 0 ieee1394 94771 1 ohci1394 sata_sil 8895 0 forcedeth 55592 0 sata_nv 23778 1 pata_amd 11962 1 floppy 63156 0

    Read the article

  • Stop duplicate icmp echo replies when bridging to a dummy interface?

    - by mbrownnyc
    I recently configured a bridge br0 with members as eth0 (real if) and dummy0 (dummy.ko if). When I ping this machine, I receive duplicate replies as: # ping SERVERA PING SERVERA.domain.local (192.168.100.115) 56(84) bytes of data. 64 bytes from SERVERA.domain.local (192.168.100.115): icmp_seq=1 ttl=62 time=113 ms 64 bytes from SERVERA.domain.local (192.168.100.115): icmp_seq=1 ttl=62 time=114 ms (DUP!) 64 bytes from SERVERA.domain.local (192.168.100.115): icmp_seq=2 ttl=62 time=113 ms 64 bytes from SERVERA.domain.local (192.168.100.115): icmp_seq=2 ttl=62 time=113 ms (DUP!) Using tcpdump on SERVERA, I was able to see icmp echo replies being sent from eth0 and br0 itself as follows (oddly two echo request packets arrive "from" my Windows box myhost): 23:19:05.324192 IP myhost.domain.local > SERVERA.domain.local: ICMP echo request, id 512, seq 43781, length 40 23:19:05.324212 IP SERVERA.domain.local > myhost.domain.local: ICMP echo reply, id 512, seq 43781, length 40 23:19:05.324217 IP myhost.domain.local > SERVERA.domain.local: ICMP echo request, id 512, seq 43781, length 40 23:19:05.324221 IP SERVERA.domain.local > myhost.domain.local: ICMP echo reply, id 512, seq 43781, length 40 23:19:05.324264 IP SERVERA.domain.local > myhost.domain.local: ICMP echo reply, id 512, seq 43781, length 40 23:19:05.324272 IP SERVERA.domain.local > myhost.domain.local: ICMP echo reply, id 512, seq 43781, length 40 It's worth noting, testing reveals that hosts on the same physical switch do not see DUP icmp echo responses (a host on the same VLAN on another switch does see a dup icmp echo response). I've read that this could be due to the ARP table of a switch, but I can't find any info directly related to bridges, just bonds. I have a feeling my problem lay in the stack on linux, not the switch, but am opened to any suggestions. The system is running centos6/el6 kernel 2.6.32-71.29.1.el6.i686. How do I stop ICMP echo replies from being sent in duplicate when dealing with a bridge interface/bridged interfaces? Thanks, Matt [edit] Quick note: It was recommended in #linux to: [08:53] == mbrownnyc [gateway/web/freenode/] has joined ##linux [08:57] <lkeijser> mbrownnyc: what happens if you set arp_ignore to 1 for the dummy interface? [08:59] <lkeijser> also set arp_announce to 2 for that interface [09:24] <mbrownnyc> lkeijser: I set arp_annouce to 2, arp_ignore to 2 in /etc/sysctl.conf and rebooted the machine... verifying that the bits are set after boot... the problem is still present I did this and came up empty. Same dup problem. I will be moving away from including the dummy interface in the bridge as: [09:31] == mbrownnyc [gateway/web/freenode/] has joined #Netfilter [09:31] <mbrownnyc> Hello all... I'm wondering, is it correct that even with an interface in PROMISC that the kernel will drop /some/ packets before they reach applications? [09:31] <whaffle> What would you make think so? [09:32] <mbrownnyc> I ask because I am receiving ICMP echo replies after configuring a bridge with a dummy interface in order for ipt_netflow to see all packets, only as reported in it's documentation: http://ipt-netflow.git.sourceforge.net/git/gitweb.cgi?p=ipt-netflow/ipt-netflow;a=blob;f=README.promisc [09:32] <mbrownnyc> but I do not know if PROMISC will do the same job [09:33] <mbrownnyc> I was referred here from #linux. any assistance is appreciated [09:33] <whaffle> The following conditions need to be met: PROMISC is enabled (bridges and applications like tcpdump will do this automatically, otherwise they won't function). [09:34] <whaffle> If an interface is part of a bridge, then all packets that enter the bridge should already be visible in the raw table. [09:35] <mbrownnyc> thanks whaffle PROMISC must be set manually for ipt_netflow to function, but [09:36] <whaffle> promisc does not need to be set manually, because the bridge will do it for you. [09:36] <whaffle> When you do not have a bridge, you can easily create one, thereby rendering any kernel patches moot. [09:36] <mbrownnyc> whaffle: I speak without the bridge [09:36] <whaffle> It is perfectly valid to have a "half-bridge" with only a single interface in it. [09:36] <mbrownnyc> whaffle: I am unfamiliar with the raw table, does this mean that PROMISC allows the raw table to be populated with packets the same as if the interface was part of a bridge? [09:37] <whaffle> Promisc mode will cause packets with {a dst MAC address that does not equal the interface's MAC address} to be delivered from the NIC into the kernel nevertheless. [09:37] <mbrownnyc> whaffle: I suppose I mean to clearly ask: what benefit would creating a bridge have over setting an interface PROMISC? [09:38] <mbrownnyc> whaffle: from your last answer I feel that the answer to my question is "none," is this correct? [09:39] <whaffle> Furthermore, the linux kernel itself has a check for {packets with a non-local MAC address}, so that packets that will not enter a bridge will be discarded as well, even in the face of PROMISC. [09:46] <mbrownnyc> whaffle: so, this last bit of information is quite clearly why I would need and want a bridge in my situation [09:46] <mbrownnyc> okay, the ICMP echo reply duplicate issue is likely out of the realm of this channel, but I sincerely appreciate the info on the kernels inner-workings [09:52] <whaffle> mbrownnyc: either the kernel patch, or a bridge with an interface. Since the latter is quicker, yes [09:54] <mbrownnyc> thanks whaffle [edit2] After removing the bridge, and removing the dummy kernel module, I only had a single interface chilling out, lonely. I still received duplicate icmp echo replies... in fact I received a random amount: http://pastebin.com/2LNs0GM8 The same thing doesn't happen on a few other hosts on the same switch, so it has to do with the linux box itself. I'll likely end up rebuilding it next week. Then... you know... this same thing will occur again. [edit3] Guess what? I rebuilt the box, and I'm still receiving duplicate ICMP echo replies. Must be the network infrastructure, although the ARP tables do not contain multiple entries. [edit4] How ridiculous. The machine was a network probe, so I was (ingress and egress) mirroring an uplink port to a node that was the NIC. So, the flow (must have) gone like this: ICMP echo request comes in through the mirrored uplink port. (the real) ICMP echo request is received by the NIC (the mirrored) ICMP echo request is received by the NIC ICMP echo reply is sent for both. I'm ashamed of myself, but now I know. It was suggested on #networking to either isolate the mirrored traffic to an interface that does not have IP enabled, or tag the mirrored packets with dot1q.

    Read the article

  • netsh add profile returns "An attempt was made to load a program with an incorrect format."

    - by Tunisia
    Using netsh, I used the following command to add a wireless profile add profile filename="c:\profiles\DLINK-Profile.xml" interface="D-Link DWA-125 N150" All parameters are valid. But I get the error "An attempt was made to load a program with an incorrect format." I know this error is related to OS architecture 64bit or 32 bit. But i'm not sure which program is not compatible. I'm using Win7 64bit

    Read the article

  • Setting up a WPA-PSK network card to connect to a WPA2 network

    - by mattshepherd
    I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

    Read the article

  • Airport Express with a PC

    - by Margaret Ashcraft
    I have and airport express and my IMac works fine with the internet connection, but my husband's PC in the basement has problems. The wireless connection comes and goes. One minute it says good connection the next unavailable. I have a PC laptop that will pick up the connection in the basement just fine.

    Read the article

  • How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

    - by MoLE
    I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

    Read the article

  • External WiFi Adapter for Eee PC 1000?

    - by Peter M
    I have an original Eee PC 1000 running the stock Xandros. I have run into problems where the internal WiFi card does not seem to have enough sensitivity to connect to a lot of access points. Although the computer will report APs in the area, unless the signal strength is over 80% (as reported by the Wireless networks application) I cannot seem get a connection. So is there a recommended USB WiFi adapter that is known to work with the Eee PC/Xandros system or in general with a Debian based system?

    Read the article

  • Mirror network packets from WiFi to Ethernet in an ASUS Router RT N53

    - by fazineroso
    I have an ASUS RT N53 router, running the default firmware (Linux 2.6.22 with busybox and uclibc). I need to capture data packets from some Wi-Fi devices I have connected to that router (iPad and some smartphones), but the router is not forwarding any package coming from Wi-Fi devices to the Ethernet Ports. Any idea how can I proceed? Available tools in the router are iptables (no tee option, though), ebtables, brctl... Currently the ethernet and Wifi devices are forming a bridge: # brctl show bridge name bridge id STP enabled interfaces br0 8000.50465dc06be2 no vlan0 eth1 No ebtables rules: # ebtables -L Bridge table: filter Bridge chain: INPUT, entries: 0, policy: ACCEPT Bridge chain: FORWARD, entries: 0, policy: ACCEPT Bridge chain: OUTPUT, entries: 0, policy: ACCEPT

    Read the article

  • Wifi problems after upgrading to 13.10

    - by Simon
    I just upgraded to Ubuntu 13.10, but since the upgrade I don't have internet access via wifi anymore. I can: See networks Connect to a network Ping myself (localhost, 192.168.0.103) I can't: Ping others (including other devices on the same wireless network, including the gateway/router) Resolve hosts Access any other external resource, whether on my own network or on the internet Using Wireshark, I noticed my computer is continuously sending ARP-requests like "Who has 192.168.0.1 [which is the gateway]? Tell 192.168.0.103". It doesn't get any replies though. When I ping another IP-address for which it knows the mac-address (from cache), it turns out a packet loss of 90% occurs, and even if a packet manages to arrive it takes around 3000ms. The output of route -n is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 9 0 0 eth1 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Before upgrading, wifi worked fine. Using other devices, wifi still works fine.Resetting the router didn't help. Ethernet still works after upgrading. Any suggestions? Update: I'm using the wl driver. Here's the relevant output of some commands: lspci | grep Wireless 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) cat /etc/modprobe.d/blacklist.conf [...] blacklist mac80211 blacklist brcm80211 blacklist cfg80211 blacklist lib80211_crypt_tkip blacklist lib80211 blacklist b43 cat /etc/rc.local sudo modprobe -r lib80211 sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_wep.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_tkip.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_ccmp.ko sudo modprobe wl exit 0 The last lines are probably how I got wireless working after the previous upgrade (wireless has been a problem after each upgrade). Update 2: added information about the exact hardware below. The hardware is an integrated device, so I ran lspci -nn | grep -i network. The output is: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01)

    Read the article

  • ubuntu 10.04: wlan0 No such device

    - by AodhanOL
    I am using a Dell xps l702x and I am using ubuntu 10.04 because I need to use f77 (don't ask) and I wasn't able to get it working on later versions of ubuntu. I cannot use the wifi at all. I have tried to fix it and have had limited success (changed the output from rfkill list all from Hard blocked: yes, to hard blocked: no). Here is the output from rfkill list all aodhan@aodhan-laptop:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-bluetooth: Bluetooth Soft blocked: no Hard blocked: no Here is the output from iwconfig: aodhan@aodhan-laptop:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. pan0 no wireless extensions. And here is the output from ifconfig -a: aodhan@aodhan-laptop:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 5c:f9:dd:3d:f2:f7 inet addr:192.168.1.17 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::5ef9:ddff:fe3d:f2f7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3417 errors:0 dropped:0 overruns:0 frame:0 TX packets:2894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3317567 (3.3 MB) TX bytes:505049 (505.0 KB) Interrupt:30 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 7e:7e:e8:39:70:af BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And finally, the output from lspci: 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1246 (rev a1) 03:00.0 Network controller: Intel Corporation Device 008a (rev 34) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Please help me! Thank you in advance. Edit: Further info - this is a dual install with a windows 7 system as the other option. However, I can't access that until tomorrow (I won't have access to the windows 7 disc until then, and grub isn't letting me load it). Therefore, I can't be sure whether it still works on that or not. It used to, though.

    Read the article

  • Can a virtual mikrotik box bridge a hyper-v internal network with a hyper-v external network?

    - by mcfrosty
    I am trying to set up a Mikrotik router as a transparent firewall on my network. I got the machine working on a hardware MT box, but my boss wants the MT virtualized. I have been trying the set up where my virtual windows box talks to the Mikrotik via private or internal network on the Hyper-V host. I can get the two machines to talk, but as soon as I set up a bridge on the MT, all traffic ceases between the two. Is it possible to create a bridge for this purpose (having the MT silently in front of my firewalled server)? I could really use some help.

    Read the article

  • Can a virtual mikrotik box bridge a hyper-v internal network with a hyper-v external network?

    - by mcfrosty
    I am trying to set up a Mikrotik router as a transparent firewall on my network. I got the machine working on a hardware MT box, but my boss wants the MT virtualized. I have been trying the set up where my virtual windows box talks to the Mikrotik via private or internal network on the Hyper-V host. I can get the two machines to talk, but as soon as I set up a bridge on the MT, all traffic ceases between the two. Is it possible to create a bridge for this purpose (having the MT silently in front of my firewalled server)? I could really use some help.

    Read the article

  • Is there a way to define a rule on a bridge that will return reply for ARP request

    - by user1495181
    client (IP = 1.1.1.1) - bridge (brctl) - server (IP = 2.2.2.2) (all machine are Ubuntu). The client block arp request. (there are multiple clients ) I need to define a rule on the bridge machine that will return the client MAC when it get ARP request for IP 1.1.1.1. I see that in ebtables there is an arpreply option , but i didnt manage to find an example to define the arpreply by given arp request ip. ebtables -t nat -A PREROUTING -p arp -j arpreply --arpreply-mac 00:09:5B:91:56:08 Can you please adcive

    Read the article

  • How do I bridge a connection from Wi-Fi to TAP on Mac OS X? (for the emulator QEMU)

    - by penx
    I'm trying to setup a bridge between my Wi-Fi connection and an emulator (QEMU). I need a virtual machine to be on the same LAN as the host, with its own IP address. QEMU requires using a TAP (virtual network device) so I have installed tuntaposx, have it running, and can open up QEMU using a TAP: qemu-system-arm -kernel zImage.integrator -initrd arm_root.img -m 256 -net nic -net tap,ifname=tap1 -nographic -append "console=ttyAMA0" I have a script that configures the bridge once QEMU has opened up the TAP interface: sysctl -w net.link.ether.inet.proxyall=1 sysctl -w net.inet.ip.forwarding=1 sysctl -w net.inet.ip.fw.enable=1 ifconfig bridge0 create ifconfig bridge0 addm en1 ifconfig tap1 0.0.0.0 up ifconfig bridge0 addm tap1 ifconfig bridge0 up If I manually set an IP on the VM, I can ping from the VM to the host, but not from the host to the VM. Also, I can't access the rest of the network from the VM - including not being able to set an IP over DHCP. Any ideas?

    Read the article

  • WebService DIME Bridge

    The DIME Bridge transferring a web service response (any serializable object) in the binary format across the Internet. It's a full transparent loosely coupled solution between the web service and its consumer - just injecting the bridge in their config files.

    Read the article

  • Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

    - by zewone
    I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686 ![Schizophrenic Ubuntu](http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

    Read the article

  • Connect to a wireless network programmatically

    - by Josh Adams
    I'm trying to write an application that connects to my company's wireless network automatically on windows XP. I've found the Wireless LAN API but it requires me to have some hotfix installed on the machine, and you need to have sp2 or higher(There are machines with SP1, and I'm required to support any XP machine). I've tried to find some samples about Wireless Zero Configuration on MSDN but with no luck, only samples I've found are for WinCE, I think Microsoft stopped supporting it. In addition I couldn't find where to download the dll and header file for working with the WZC. There must be a way to do it and work on any service pack because I've found Zwlancfg by ENGL

    Read the article

  • How to troubleshoot and tweek unreasonably slow wireless connection on Ubuntu?

    - by Leonid
    I've just acquired a USB F5D8053ed Belkin adapter and it is unreasonably slow. Details of how I installed the firmware and device driver is described in this AU Question. I believe there is either a problem with a driver or adapter itself that is preventing from using the full network quality. At the moment I can see that the my Windows laptop is perfroming at 30 x speed better than the Ubuntu desktop PC with Belkin. What are they ways to troubleshoot pure wireless network performance on Ubuntu?

    Read the article

  • My Encore N300 wireless usb doesn't connect, any workarounds?

    - by rafa
    I decided to wipe Windows 7 and made a full installation. Everything works great but for a Encore N300 wireless usb dongle that I use on my desktop. Ubuntu seems to recognize it and I can browse the available networks, but I can connect to any of them. I was told that I should download its drivers, and so I did it, but I don't know how to install them. Please, I'd like to know if my connectivity problem is really a driver issue or some other thing.

    Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >