Search Results

Search found 14402 results on 577 pages for 'mouse properties'.

Page 381/577 | < Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >

• USB drives not recognized all of a sudden (module usb_storage not loading)

  - by Siddharth

  I am very close to the solution, just need to know how to get usb-storage to load I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• Customize the Background in Boxee

  - by DigitalGeekery

  Are you a Boxee user who thinks the default background is little boring? Today we’ll take a look at how to freshen up the look of Boxee by changing the background. Boxee Background When you log into Boxee, select the Settings button at the upper left corner of the Home page.   Select General on the Settings screen. When you select or hover your mouse over the Background Image button, you’ll see options to set a background image or set a background image folder. You’ll have the option of settings a single static image as your background, or choosing an images folder.   If you choose a folder, Boxee will rotate through the images in the folder. To set Background images folder, select that option. Browse for your image folder.. And then select OK.   Boxee will rotate through the images in the folder.   Images will change every ten seconds.   If you prefer a single static image, select Set background image   Choose a image and select OK. Now just enjoy you nice new backgrounds.   If you ever wish to revert back to the default Boxee background, simply select Reset Images on the Settings \ General screen. Adding your own backgrounds is a nice way to customize your Boxee experience. Ideally, you’ll want to choose high resolution images and images oriented as landscape rather than portrait. If you are unfamiliar with Boxee, check out our article on getting started with Boxee.  Looking for a Boxee remote? Read how to use your iPhone or iPod Touch as a Boxee remote. Similar Articles Productive Geek Tips Integrate Boxee with Media Center in Windows 7Using Pandora in BoxeeWatch Netflix Instant Movies in BoxeeUse your iPhone or iPod Touch as a Boxee RemoteCustomize the Windows 7 Logon Screen TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 Use ILovePDF To Split and Merge PDF Files TimeToMeet is a Simple Online Meeting Planning Tool Easily Create More Bookmark Toolbars in Firefox Filevo is a Cool File Hosting & Sharing Site Get a free copy of WinUtilities Pro 2010 World Cup Schedule

  Read the article

• How to Create a Task From an Email Message in Outlook 2013

  - by Lori Kaufman

  If you need to do something related to an email message you received, you can easily create a task from the message in Outlook. A task can be created that contains all the content of the message without requiring you to re-enter the information. Creating a task in Outlook from an email message is different from flagging the message. As it says on Microsoft’s site: “When you flag an email message, the message appears in the To-Do List in Tasks and on the Tasks peek. However, if you delete the message, it also disappears from the To-Do List in Tasks and on the Tasks peek. Flagging a message doesn’t create a separate task.” Using the method described below to create a task from an email message, the task is separate from the message. The original message can be deleted or changed and the related task will not be affected. In Outlook, make sure the Mail section is active. If not, click Mail on the Navigation Bar at the bottom of the Outlook window. Then, click on the message you want to add to a task and drag it to Tasks on the Navigation Bar. A new Task window displays containing the email message and allowing you to enter the subject of the task, the Start and Due dates, Status, Priority, among other settings. When you have specified the settings for the task, click Save & Close in the Actions section of the Task tab. When the Task window closes, the Mail section is still active. If you move your mouse over Tasks on the Navigation Bar, a snippet from the new task displays in a popup window (the Task peek). Click Tasks to go to the Tasks section of Outlook. The To-Do List displays with your newly-added task listed in the middle pane. The right pane displays the details of the task and the contents of the message included in the task (as pictured at the beginning of this article). Click on Tasks to see a complete listing of all your tasks, including the one you just added from your email message. Note that attachments in an email message added to a new task are not copied to the task. You can also create new tasks by dragging contacts, calendar items, and notes to Tasks on the Navigation Bar.     

  Read the article

• Media keys play/pause globally worked in 12.10, not in 13.10

  - by Stéphane Gourichon

  Laptop media keys On Asus n55sf laptop, there are a dedicated keys for volume up, volume down, mute, [play/pause], stop, launch (plus a dozen Fn-key combinations). In 12.10 most worked. (Overall is seems unrelated to desktop environment used, stating it for the sake of completeness.) On Ubuntu 12.10 under XFCE they just worked. That is: when a player like rhythmbox or totem was started, it would alternate between play and pause. Interestingly, if several were started, they would alternate independently. E.g. use mouse to pause rhythmbox, launch totem, and one hit on [play/pause] key would pause one and resume the other. Keys Next,Previous and Stop worked as expected in any program. In 13.10 most still work, but play/skip related ignored. On Xubuntu 13.10 (XFCE too) the volume keys work but the [play/pause], stop, next and prev are ignored. Not tried regular Ubuntu 13.10 (Unity). Search before you ask Here are a few facts: https://wiki.ubuntu.com/Hotkeys/Architecture is ummutable and mentions Ubuntu 9.10. https://wiki.ubuntu.com/Hotkeys/Troubleshooting is also outdated as it mentions /usr/share/doc/udev/README.keymap.txt which no longer exists. On 12.10 and 13.10 versions, at XFCE level (as visible by xfconf-query or using xfce4-settings-manager) there are a couple of shortcut for keys like XF86Calculator or XF86TouchpadToggle but nothing related to volume prev/next/play/stop, which is okay. XF86Audio substring doesn't appear in /etc (which is normal) Kernel-level test: "showkey -s" on console shows that keys Next,Play/Pause,Previous,Stop are keycodes 163,164,165,166. Nothing relevant in /etc about that. Reports https://bugs.launchpad.net/ubuntu/+source/udev/+bug/1072371 and https://bugs.launchpad.net/ubuntu/+source/systemd/+bug/1012365 suggest to adjust at udev level. Alas, the udev tutorials I found ( e.g. https://wiki.debian.org/udev ) don't even mention keyboard. A thread in french seems to deal with a similar issue: https://forum.ubuntu-fr.org/viewtopic.php?id=1395051. @sudo evtest /dev/input/event3@, in X as well as on plain console, reports events on key pressed and repeats, but nothing when pressing those media keys. Is udev a dead end ? Questions How did it work in 12.10 ? Through udev ? Something else ? Any other hint ?

  Read the article

• permanently load module

  - by Radu

  I have a Compaq Presario CQ-61 320SQ, I am using Ubuntu 10.04 because after update to 10.10 my mouse and touchpad won't work, network won't work, sound won't work ... (I managed to fix most of them after almost a month of googling, but not all, my 2 Desktops have no problem with 10.10) so I decided to switch back to 10.04, where I have a problem: My broadband speed is very low beacause of the kernel module r8169, I downloaded the good module r8101 and every time the computer boots have a rc.local entry to fix this. Question: Can I load the modul permanently from a specific location. I heard about /etc/modules but there I need the module name, but I have to load it from a specific path (where is the default path for that) Thank you. So I studied the script: It creates the file r8101.ko in /lib/modules/uname -r/kernel/drivers/net so I think as long as nobody will delete that file, and I don't update the kernel, maybe adding r8108 to /etc/modules will work, and add r8169 to blacklist ... I will give it a try. EDIT2: So I added r8101 to /etc/modules and blacklist r8169 to /etc/modprobe.d/blacklist.conf It still uses the old module, lsmod prints: radu@adu:~$ lsmod | grep r8 r8101 67626 0 r8169 34108 0 mii 4381 1 r8169 EDIT: the module is loaded using this script that came with it: #!/bin/sh # invoke insmod with all arguments we got # and use a pathname, as insmod doesn't look in . by default TARGET_PATH=/lib/modules/`uname -r`/kernel/drivers/net echo echo "Check old driver and unload it." check=`lsmod | grep r8169` if [ "$check" != "" ]; then echo "rmmod r8169" /sbin/rmmod r8169 fi check=`lsmod | grep r8101` if [ "$check" != "" ]; then echo "rmmod r8101" /sbin/rmmod r8101 fi echo "Build the module and install" echo "-------------------------------" >> log.txt date 1>>log.txt make all 1>>log.txt || exit 1 module=`ls src/*.ko` module=${module#src/} module=${module%.ko} if [ "$module" == "" ]; then echo "No driver exists!!!" exit 1 elif [ "$module" != "r8169" ]; then if test -e $TARGET_PATH/r8169.ko ; then echo "Backup r8169.ko" if test -e $TARGET_PATH/r8169.bak ; then i=0 while test -e $TARGET_PATH/r8169.bak$i do i=$(($i+1)) done echo "rename r8169.ko to r8169.bak$i" mv $TARGET_PATH/r8169.ko $TARGET_PATH/r8169.bak$i else echo "rename r8169.ko to r8169.bak" mv $TARGET_PATH/r8169.ko $TARGET_PATH/r8169.bak fi fi fi echo "Depending module. Please wait." depmod -a echo "load module $module" modprobe $module echo "Completed." exit 0

  Read the article

• USB drives not recognized all of a sudden (usb_storage not loaded lsmod does not report usb_storage)

  - by Siddharth

  I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• Extensible Metadata in Oracle IRM 11g

  - by martin.abrahams

  Another significant change in Oracle IRM 11g is that we now use XML to create the tamperproof header for each sealed document. This article explains what this means, and what benefit it offers. So, every sealed file has a metadata header that contains information about the document - its classification, its format, the user who sealed it, the name and URL of the IRM Server, and much more. The IRM Desktop and other IRM applications use this information to formulate the request for rights, as well as to enhance the user experience by exposing some of the metadata in the user interface. For example, in Windows explorer you can see some metadata exposed as properties of a sealed file and in the mouse-over tooltip. The following image shows 10g and 11g metadata side by side. As you can see, the 11g metadata is written as XML as opposed to the simple delimited text format used in 10g. So why does this matter? The key benefit of using XML is that it creates the opportunity for sealing applications to use custom metadata. This in turn creates the opportunity for custom classification models to be defined and enforced. Out of the box, the solution uses the context classification model, in which two particular pieces of metadata form the basis of rights evaluation - the context name and the document's item code. But a custom sealing application could use some other model entirely, enabling rights decisions to be evaluated on some other basis. The integration with Oracle Beehive is a great example of this. When a user adds a document to a Beehive workspace, that document can be automatically sealed with metadata that represents the Beehive security model rather than the context model. As a consequence, IRM can enforce the Beehive security model precisely and all rights configuration can actually be managed through the Beehive UI rather than the IRM UI. In this scenario, IRM simply supports the Beehive application, seamlessly extending Beehive security to all copies of workspace documents without any additional administration. Finally, I mentioned that the metadata header is tamperproof. This is obviously to stop a rogue user modifying the metadata with a view to gaining unauthorised access - reclassifying a board document to a less sensitive classifcation, for example. To prevent this, the header is digitally signed and can only be manipulated by a suitably authorised sealing application.

  Read the article

• Silverlight Cream for May 12, 2010 -- #860

  - by Dave Campbell

  In this Issue: Miroslav Miroslavov(-2-), Mike Snow(-2-, -3-), Paul Sheriff, Fadi Abdelqader, Jeremy Likness, Marlon Grech, and Victor Gaudioso. Shoutouts: Andy Beaulieu has a cool WP7 game up and is looking for opinions/comments: Droppy Pop: A Windows Phone 7 Game Karl Shifflett has code and video tutorials up for the app he wrote for the WPF LOB tour he just did: Stuff – WPF Line of Business Using MVVM Video Tutorial From SilverlightCream.com: Flipping panels I had missed this 3rd part of the CompleteIT explanation. In this post Miroslav Miroslavov describes the page flipping they're doing. Great explanation and all the code included. Flying objects against you The 4th part of the CompleteIT explanation is blogged by Miroslav Miroslavov where he is discussing the screen elements 'flying toward' the user. Silverlight Tip of the Day #17 – Double Click Mike Snow's Tip of the Day 17 is showing how to implement mouse double-clicks either for an individual control or for an entire app. Silverlight Tip of the Day #18 – Elastic Scrolling In Mike Snow's Tip of the Day 18, he's talking about and showing some 'elastic' scrolling in his image viewer application. He's asking for opinions and suggestions. Silverlight Tip of the Day #19 – Using Bing Maps in Silverlight Mike Snow's Tips are getting more elaborate :) ... Number 19 is about using the BingMap control in your Silverlight app. Control to Control Binding in WPF/Silverlight Paul Sheriff demonstrates control to control binding... saving a bunch of code behind in the process. Project included. Your First Step to the Silverlight Voice/Video Chatting Client/Server Fadi Abdelqader has a post up at CodeProject using the WebCam and Mic features of Silverlight 4 to setup a voice & video chatting app. MVVM Coding by Convention (Convention over Configuration) Jeremy Likness discusses Convention over Configuration and gives up some good MVVM nuggets along the way... check out his nice long post and grab the source for the project too... and also check out the external links he has in there. MEFedMVVM changes >> from cool to cooler Marlon Grech has refactored MEFedMVVM, and in addition is working with other MVVM framework folks to use some of the same MEF techniques in theirs... code on CodePlex New Silverlight Video Tutorial: How to Create a Silverlight Paging System to Load new Pages In Victor Gaudioso's latest video tutorial he builds a ContentHolder UserControl that will load any page on demand into your MainPage.xaml Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• View the Real Links Behind Shortened URLs in Chrome

  - by Asian Angel

  When you encounter shortened URLs there is always that worry in the back of your mind about where they really lead to. Now you can get a “sneak peak” at the real links behind those URLs with the View Thru extension for Google Chrome. The URL Shortening services officially supported at this time are: bit.ly, cli.gs, ff.im, goo.gl, is.gd, nyti.ms, ow.ly, post.ly, su.pr, & tinyurl.com. Before When you encounter a shortened URL you are pretty much on your own in deciding whether to trust that link or not. It would really be nice if you could just hover your mouse over those links and know where they will lead ahead of time. After Once you have the extension installed you are ready to access that link viewing goodness. Please note that you will need to reload any pages that were open prior to installing the extension. For our first example we chose a shortened URL from “bit.ly”. As you can see the entire link behind the shortened URL is displayed very nicely…no hidden surprises there! Note: There are no options to worry with for the extension. Another perfect result for the “goo.gl URL” shown below. View Thru will certainly remove a lot of the stress related to clicking on shortened URLs. Bonus Find Just out of curiosity we looked for a shortened URL not listed as being officially supported at this time. We found one with the “http://nyti.ms/” domain and View Thru showed the link perfectly…so be sure to give it a try on other services too. Conclusion If you worry about where a shortened URL will really lead you then the View Thru extension can help alleviate that stress. Links Download the View Thru extension (Google Chrome Extensions) Similar Articles Productive Geek Tips See Where Shortened URLs “Link To” in Your Favorite BrowserVerify the Destinations of Shortened URLs the Easy WayCreate Shortened goo.gl URLs in Google Chrome the Easy WayCreate Shortened goo.gl URLs in Your Favorite BrowserAccess Google Chrome’s Special Pages the Easy Way TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job?

  Read the article

• English-Focused Translation Bookmarklet for Your Browser

  - by Asian Angel

  Are you wanting a translation bookmarklet that just focuses on translating websites into English? Then you will want to take a look at the To English Bookmarklet. Get the Bookmarklet To install the To English Bookmarklet visit the webpage at Lifehacker (link below), grab the bookmarklet with your mouse, and drag it to your “Bookmarks Toolbar”. Now you are ready for one-click translation into English. To English in Action We decided to test our new bookmarklet on two different International Mozilla websites. The first one was in Swedish… One click and there it is. Notice that there is a “translation bar frame” that will still let you choose yet another language to translate the webpage into if you desire. Definitely a nice touch… Our second example was in Russian. Once again a single click and… The website is now in English. On this particular page the “central green graphic” was affected by the translation and the two sidebar buttons are “pre-made” but that is ok. You can read what you need to without any problems. Conclusion If you have been wanting a bookmarklet that just focuses on translating into English then this should be perfect for you. If you are looking for a bookmarklet that gives you access to a Google Translation Bar then be certain to see our article here. Links Add the To English Bookmarklet to Your Browser Similar Articles Productive Geek Tips Add a Google Translation Bar to Your Favorite BrowserSkip “Next Links” with the PageZipper BookmarkletCreate Shortened goo.gl URLs in Your Favorite BrowserQuickly Translate Text to Another Language in Word 2007See Where Shortened URLs “Link To” in Your Favorite Browser TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Find Downloads and Add-ins for Outlook Recycle ! Find That Elusive Icon with FindIcons Looking for Good Windows Media Player 12 Plug-ins? Find Out the Celebrity You Resemble With FaceDouble Whoa !

  Read the article

• A Slice of Raspberry Pi

  - by Phil Factor

  Guest editorial for the ITPro/SysAdmin newsletter The Raspberry Pi Foundation has done a superb design job on their new $35 network-enabled Linux computer. This tiny machine, incorporating an ARM processor on a Broadcom BCM2835 multimedia chip, aims to put the fun back into learning computing. The public response has been overwhelmingly positive.Note that aim: "…to put the fun back". Education in Information Technology is in dire straits. It always has been, but seems to have deteriorated further still, even in the face of improved provision of equipment.In many countries, the government controls the curriculum. It predicted a shortage in office-based IT skills, and so geared the ICT curriculum toward mind-numbing training in word-processing and spreadsheet skills. Instead, the shortage has turned out to be in people with an engineering-mindset, who can solve problems with whatever technologies are available and learn new techniques quickly, in a rapidly-changing field.In retrospect, the assumption that specific training was required rather than an education was an idiotic response to the arrival of mainstream information technology. As a result, ICT became a disaster area, which discouraged a generation of youngsters from a career in IT, and thereby led directly to the shortage of people with the skills that are required to exploit the potential of Information Technology..Raspberry Pi aims to reverse the trend. This is a rig that is geared to fast graphics in high resolution. It is no toy. It should be a superb games machine. However, the use of Fedora, Debian, or Arch Linux ARM shows the more serious educational intent behind the Foundation's work. It looks like it will even do some office work too!So, get hold of any power supply that provides a 5VDC source at the required 700mA; an old Blackberry charger will do or, alternatively, it will run off four AA cells. You'll need a USB hub to support the mouse and keyboard, and maybe a hard drive. You'll want a DVI monitor (with audio out) or TV (sound and video). You'll also need to be able to cope with wired Ethernet 10/100, if you want networking.With this lot assembled, stick the paraphernalia on the back of the HDTV with Blu Tack, get a nice keyboard, and you have a classy Linux-based home computer. The major cost is in the T.V and the keyboard. If you're not already writing software for this platform, then maybe, at a time when some countries are talking of orders in the millions, you should consider it.

  Read the article

• How to get my IR remote to work? Lirc can't see it

  - by user1234567

  I'm using Ubuntu 11.10 (amd64) and I'm trying to get my infrared remote control working. The IR device is a part of a DVB-T USB stick (Based on a RTL2832u chip). I'm using these drivers - it's the only way of getting this device to work under 11.10 that I found. It's a big impromevent from previous Ubuntu version, where I had to edit the driver's code. The device works quite great - and the IR part of it works, too. The driver's page says that the code it's in alpha stage, but I'm pretty sure that my issue has nothing to do with that. If, and only if driver's module is loaded with parameter rtl2832u_rc_mode=2 (which means "use NEC protocol for IR") the remote kind of works, I can see this by running cat /dev/.. ../input6 - when I press a button, random letters appear. The remote works just like a keyboard, but keys are totally messed up - when I press '5' the volume goes down, etc. I would like to use Lirc to fix that, but Lirc can't detect my device (i.e. irw shows nothing). I suspect, it's because something gets into control of the device and sets it up as a keyboard. Lirc seems to be working, it's KDE settings module works too, but it just doesn't detect the device. The Lirc page describes this issue, but since 2009 - the last year when that page was updated, Ubuntu moved from HAL (described there) to DeviceKit, rendering provided instruction useless. I had a similar issue with my previous remote, but the keys were not messed up so much - the remote was usable, so I gave up trying to get Lirc working. I tried the answer provided here, but it changed nothing. I also tried forcing lircd to use my device, but this didn't work too: for i in /sys/class/input/input* ; do echo -n "$(basename "$i"): "; cat "$i/name"; done shows input0: Power Button input1: Power Button input2: Logitech Logitech USB Keyboard input3: A4Tech PS/2+USB Mouse input6: IR-receiver inside an USB DVB receiver But when I run: lircd -n --device=name='IR*' as root (also tried with the full name) I always see: lircd-0.9.0[3983]: lircd(default) ready, using /var/run/lirc/lircd lircd-0.9.0[3983]: accepted new client on /var/run/lirc/lircd lircd-0.9.0[3983]: could not get file information for name=IR* lircd-0.9.0[3983]: default_init(): No such file or directory lircd-0.9.0[3983]: Failed to initialize hardware So, how to set up Lirc with devinput driver in such case?

  Read the article

• Script For Detecting Availability of XMLHttp in Internet Explorer

  - by Duncan Mills

  Having the XMLHttpRequest API available is key to any ADF Faces Rich Client application. Unfortunately, it is possible for users to switch off this option in Internet Explorer as a Security setting. Without XMLHttpRequest available, your ADF Faces application will simply not work correctly, but rather than giving the user a bad user experience wouldn't it be nicer to tell them that they need to make some changes in order to use the application?  Thanks to Blake Sullivan in the ADF Faces team we now have a little script that can do just this. The script is available from https://samplecode.oracle.com here - The attached file browserCheck.js is what you'll need to add to your project.The best way to use this script is to make changes to whatever template you are using for the entry points to your application. If you're not currently using template then you'll have to make the same change in each of your JSPX pages. Save the browserCheck.js file into a /js/ directory under your HTML root within your UI project (e.g. ViewController)In the template or page, select the <af:document> object in the Structure window. From the right mouse (context) menu choose Facet and select the metaContainer facet.Switch to the source code view and locate the metaContainer facet. Then insert the following lines (I've included the facet tag for clarity but you'll already have that):      <f:facet name="metaContainer">        <af:resource type="javascript"                      source="/js/browserCheck.js"/>        <af:resource type="javascript">           xmlhttpNativeCheck(                     "help/howToConfigureYourBrowser.html");        </af:resource>      </f:facet>Note that the argument to the xmlhttpNativeCheck function is a page that you want to show to the user if they need to change their browser configuration. So build this page in the appropriate place as well. You can also just call the function without any arguments e.g. xmlhttpNativeCheck(); in which case it will pop up default instructions for the user to follow, but not redirect to any other page.

  Read the article

• how to start LXDE session automatically after tightvncserver starts to make me able see desktop when connecting to the host via vncclient?

  - by Oleksandr Dudchenko

  I have system which is equipped with Intel Celeron processor 1.1 GHz s370 with 384 Mb of RAM on Intel d815egew motherboard which supports wake-on-lan function. I want to use such a PC for Internet sharing to the local network. Also this PC is a DHCP+DNS server as well as router/gateway. Based on above I decided to install Lubuntu as it is lightweight system. I installed Lubuntu 10.04.4 LTS from alternate ISO. System has no auto login. System boots and has acceptable performance. Host PC has onboard 4 network adapters: eth0 – ethernet controller which is used for Local Network connections. Has static address 10.0.0.1 eth1 – ethernet controller which is not used and not configured so far, I plan to connect printer here later on. eth2 - ethernet controller which is used to connect to Internet, which we plan to share for the local network wlan0 – wireless controller, it is used in role of access poit for local Network and has address 10.0.0.2 We want to control our gateway remotely. So, we need to be able to power it on remotely. To allow this I’ve done the following things: $ cd /etc/init.d/ made a new file with command $ sudo vim wakeonlanconfig Wrote the following lines to the newly created file, saved and closed it #!/bin/bash ethtool -s eth0 wol g ethtool -s eth2 wol g exit Made the abovementioned file executable $ sudo chmod a+x wakeonlanconfig Then included it into autostart sequence during boot. $ sudo update-rc.d -f wakeonlanconfig defaults after system reboot we will be able to poweron system remotely. Than we need to have a possibility to connect remotely to the host via SSH and VNC. So, I installed following packets with the following commands: $ sudo apt-get update $ sudo apt-get install openssh-server tightvncserver Add ssh daemon into autostart sequence during boot. $ sudo update-rc.d -f ssh defaults Power off the host PC $ sudo halt Then I went to remote place, send magic paket and powered the Host up. System started... And I connected to the host via Putty from remote system under Windows. Than logged in and run the command to start vnc server. $ tightvncserver -geometry 800x600 -depth 16 :2 VNC server successfully started and I got message like follows. New 'X' desktop is gateway:2 Starting applications specified in /home/dolv/.vnc/xstartup Log file is /home/dolv/.vnc/gateway:2.log Using UltraVNC Viewer programm under windows I connected to the host's vnc server, enterd the password and.... sow only mouse cursor in form of cross on a grey background of 800x600 dots, no desktop. Here is my .vnc/xstartup file #!/bin/sh xrdb $HOME/.Xresources xsetroot -solid grey #x-terminal-emulator -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & #x-window-manager & # Fix to make GNOME work export XKL_XMODMAP_DISABLE=1 /etc/X11/Xsession The Question: What I have to change and where to make LXDE session start automatically after tightvncserver starts?

  Read the article

• Preview Links and Images in Google Chrome

  - by Asian Angel

  Anyone who has used the CoolPreviews extension in Firefox knows how wonderful that preview window can be. Now you can get the same kind of functionality in Chrome with the ezLinkPreview extension. Note: Extension will not work on websites containing “frame buster” code (navigation to the actual URL will occur). Before Normally if you want to have a better look at a particular webpage the only option you have is to go ahead and open it in a new tab or window. But it would certainly be nice to be able to take a quick “sneak peek” before-hand… After As soon as you have finished installing the extension everything is ready to go…just refresh any pages open prior to installation and enjoy the preview goodness. When you hover your mouse near any link you will notice a small “Preview Button” appear with the letters “EZ” inside. A closer look at the “Preview Button”. Click on the “Preview Button” to open the popup window. Now you can get a very good idea of whether the page is worth visiting or not. Here is a closer look at the popup window. Notice that you can see the URL for the webpage and access a convenient set of buttons on the right side (Open to new tab, Pin to keep overlay open, and Close). You can even resize the window as desired to best suit your needs (you can actually grab any of the four corners to resize the popup window). It is also possible to open a “preview window” inside the popup window…you can see the “Preview Button” here… If you have Chrome maximized you can enjoy using a large sized “preview window”. Now that is nice! For those who may be curious you can see that ezLinkPreview works nicely with images too. Conclusion The ezLinkPreview extension provides a quick and simple way to preview links and/or images while you are browsing. If you are looking for similar functionality in Firefox then be sure to read our article on CoolPreviews here. Links Download the ezLinkPreview extension (Google Chrome Extensions) Similar Articles Productive Geek Tips Google Image Search Quick FixSubscribe to RSS Feeds in Chrome with a Single ClickFind a Website’s Actual Location with Chrome FlagsHow to Make Google Chrome Your Default BrowserEnable Auto-Paging Goodness in Google Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job?

  Read the article

• Win7 is not a tablet OS, no matter what the boys in Redmond think.

  - by John Conwell

  Despite what execs at Microsoft think, Windows 7 is NOT a tablet OS.  Just because you can install some software (or OS) on a device, doesn't mean that device is meant to run that software.  This seems to be the step that the non-engineer execs at Microsoft have seem to not understood.  In order to seamlessly work with a device, the software needs to be designed with that device in mind.  That has been the problem with the Windows PDA platform, the Windows Mobil platform, and now with trying to force fit Windows 7 on a tablet.  Its just not designed for that style of interaction.   Windows is designed to be interacted with via a mouse and keyboard.  In fact, it is brilliant at that.  But, It is NOT designed to be interacted with by your fingers.  And that is why the Windows tablet failed 10 years ago, and why it will fail today.  Its not the hardware's fault like Microsoft claimed 10 years ago.  Its the User Interaction design that failed. And this is why the iPhone and Android OS's work wonderfully on a tablet.  The user interaction was designed for small screens, navigated by big fat fingers.  I love these OS's and how I interact with them.  And when I play with a touch screen Windows 7 device, I am feel like I'm playing with a brittle wana-be.  And its not the hardware's fault.  The touchscreen is very responsive.  I actually like the hardware.  But the OS and the software are just not designed to be interacted with, with my big fat fingers.  In order to be successful, Microsoft needs to start from scratch, and build a platform AND SOFTWARE specifically for use by fingers.  Thats why everyone was so excited when they though Microsoft was going to release the Courier tablet.  Because it looked like a totally different platform.  Something that might actually work.  But Windows 7...I hate to burst your bubble, but you are not a touch platform.

  Read the article

• Friday Fun: Snowball

  - by Asian Angel

  It is Christmas Eve and hopefully you are enjoying the start of an early weekend away from work. This week we have a snowball throwing game for you to try out, so bundle up and get ready to let those snowballs fly! Snowball The object of the game is to use your snowball ammo to harass the drunk businessman and send him flying along distance-wise as far as you can. Simply use your mouse to aim and click the left button to throw snowballs. You can monitor your stats on the silver bar towards the top of the window. The sound can also be disabled if the music is bothering you, but keep in mind that all sound will be disabled if you use the option. Time to get those snowballs flying through the air!! Keep hitting the businessman with your snowballs as you chase after him. Make certain that your aim is good or you will quickly run out of snowballs! You can really get him moving along at a good rate and he can even go high enough in the air to disappear off the screen for a few moments. There is a also chance that your aim will be so wicked with the snowballs that you will literally knock the drunk businessman’s head off! Weird but possible… The game ends when one of these two events occur: 1.) you run out of snowballs or 2.) the businessman literally bounces back at and then drops behind you as seen in the screenshot here. The moment either happens your score will pop up and then you have the opportunity to try again. Have fun! Note: The bounce back event can happen when encountering cars. Play Snowball Latest Features How-To Geek ETC How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Is Your Desktop Printer More Expensive Than Printing Services? 20 OS X Keyboard Shortcuts You Might Not Know HTG Explains: Which Linux File System Should You Choose? HTG Explains: Why Does Photo Paper Improve Print Quality? An Alternate Star Wars Christmas Special [Video] Sunset in a Tropical Paradise Wallpaper Natural Wood Grain Icons for Your Desktop and App Launcher Docks My Blackberry Is Not Working! The Apple Too?! [Funny Video] Hidden Tracks Your Stolen Mac; Free Until End of January Why the Other Checkout Line Always Moves Faster

  Read the article

• Stop YouTube Videos from Automatically Playing in Chrome

  - by The Geek

  If you’ve actually used the internet before, you’ve probably come across a page with an auto-playing YouTube clip, and chances are good it was a rather annoying one. Here’s how to stop them from starting automatically in Chrome. We’ve already told you how to stop them from automatically playing if you’re a Firefox user (best answer: use Flashblock!), but now it’s time for Chrome users to get their turn. Use the Stop Autoplay for YouTube Extension The great thing about this extension is that it stops the video from playing, but it allows it to continue buffering, so when you do feel like playing the video, it’ll already be downloaded—really useful for people with slower internet connections. There’s no UI or anything fancy, just head to the extension page and click the Install button. If you want to get rid of it later, use the Tools –> Extensions menu (or you can type chrome://extensions/ into your address bar), and then click the Uninstall link for that add-on.   Download Stop Autoplay for YouTube [Google Chrome Extensions] Using FlashBlock for Chrome If you really wanted to, you could just disable Flash across the board using FlashBlock for Chrome. Once you’ve installed the extension, you won’t see any Flash elements anywhere, and you’ll have to move your mouse over them and click to enable them each time. When I installed the extension the first time, I noticed that YouTube was already in the allow list. I’m not sure if that’s the default setting or not, but you can use the icon in the address bar, or the Options from the Extensions panel to get to the settings page, and from there you can remove anything from the White List that you wouldn’t want. Another nice feature about Flash Block is that it can also block Silverlight, or you could simply uninstall or remove unnecessary Chrome plug-ins. Download FlashBlock for Chrome Similar Articles Productive Geek Tips Stop YouTube Videos from Automatically Playing in FirefoxDisable YouTube Comments while using ChromeApologies About An Awful Audio AdvertisementImprove YouTube Video Viewing in Google ChromeWatch YouTube Videos in Cinema Style in Firefox TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites

  Read the article

• Xorg.conf (nvidia) Second Monitor getting settings of first

  - by HennyH

  I've been spending the weekend (and some time before that) trying to set up my Korean QHD270 and Benq G2222HDL monitors with Ubuntu 13.10. With the nouveau drivers install both monitor function perfectly fine. After installing the nvidia drivers the Benq works but the QHD270 does not. Now, after days of struggling I managed to get the QHD270 to work following a mixture of blogs, particularly; this one and learnitwithme. Now, unfortunatly my G2222HDL does not work. I fixed the QHD270 by supplying a custom EDID, my xorg.conf looks like so (excluding keyboard and mouse): Section "ServerLayout" Identifier "Layout0" Screen "Default Screen" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Section "Device" Identifier "Configured Video Device" Driver "nvidia" Option "CustomEDID" "DFP:/etc/X11/edid-shimian.bin" EndSection Section "Screen" Identifier "Default Screen" Device "Configured Video Device" Monitor "Configured Monitor" EndSection Now, I tried defining a new Device,Monitor and Screen then in ServerLayout adding Screen "Second Screen" RightOf "Default Screen", but after doing so neither monitor worked. Hoping to fix the issue using a GUI based tool I opened up NVIDIA X Server Settings, which shows my current layout as: It seems that something is being output to the monitor, as suggested by my print screen: Any help would be greatly appreciated. Output of xrandr: Screen 0: minimum 8 x 8, current 5120 x 1440, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 connected primary 2560x1440+0+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ HDMI-0 disconnected (normal left inverted right x axis y axis) DP-0 disconnected (normal left inverted right x axis y axis) DVI-D-0 connected 2560x1440+2560+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ DP-1 disconnected (normal left inverted right x axis y axis) And an extract from my log file (perhaps this is relevant?) [ 7.862] (--) NVIDIA(0): Valid display device(s) on GeForce GTX 680 at PCI:2:0:0 [ 7.862] (--) NVIDIA(0): CRT-0 [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0) (boot, connected) [ 7.862] (--) NVIDIA(0): DFP-1 [ 7.862] (--) NVIDIA(0): DFP-2 [ 7.862] (--) NVIDIA(0): DFP-3 [ 7.862] (--) NVIDIA(0): DFP-4 [ 7.862] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): Internal Dual Link TMDS [ 7.862] (--) NVIDIA(0): DFP-1: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-2: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-2: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-3: 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-3: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-4: 960.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-4: Internal DisplayPort

  Read the article

• How do I set up nvidia graphics adapter to put out 1080p, it seems to be using interlace mode>

  - by keepitsimpleengineer

  After upgrading to 12.04, my mythbuntu client/server seems to be running in 1080i, the clue comes from: [ 1176.117] (II) NVIDIA(0): Setting mode "1920x1080_60i" [ 1231.340] (II) NVIDIA(0): Setting mode "DFP-1:1920x1080_60@1920x1080+0+0" This is from Xorg.0.log. This whole thing started from video tearing when watching Mythtv recordings. It didn't happen in 10.10. Should I use "TVStandard" "HD1080p" in the screen section since this is a dedicated HTPC? It only connects to an HDTV (1080p) via hdmi. Here is the current xorg.conf file: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 270.29 (buildd@allspice) Fri Feb 25 14:42:07 UTC 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup # InputDevice "Keyboard0" "CoreKeyboard" # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup # InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" FontPath "unix/:7100" EndSection # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup #Section "InputDevice" # # generated from default # Identifier "Mouse0" # Driver "mouse" # Option "Protocol" "auto" # Option "Device" "/dev/psaux" # Option "Emulate3Buttons" "no" # Option "ZAxisMapping" "4 5" #EndSection # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup #Section "InputDevice" # # generated from default # Identifier "Keyboard0" # Driver "kbd" #EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "SAMSUNG" HorizSync 26.0 - 81.0 VertRefresh 24.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 240" Option "TripleBuffer" "1" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "DFP: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection After a little digging, the question changes slightly, to wit... Per Chapter 19 of nvidia README... "If the EDID for the display device reported a preferred mode timing, and that mode timing is considered a valid mode, then that mode is used as the "nvidia-auto-select" mode." The EDID for my HDMI connected LCD monitor says use first device as preferred. Prefer first detailed timing : Yes Also: (--) NVIDIA(0): EDID maximum pixel clock : 230.0 MHz The list: (from startx -- -verbose 6 ) (--) NVIDIA(0): Detailed Timings: (--) NVIDIA(0): 1920 x 1080 @ 60 Hz (--) NVIDIA(0): Pixel Clock : 148.50 MHz (--) NVIDIA(0): HRes, HSyncStart : 1920, 2008 (--) NVIDIA(0): HSyncEnd, HTotal : 2052, 2200 (--) NVIDIA(0): VRes, VSyncStart : 1080, 1084 (--) NVIDIA(0): VSyncEnd, VTotal : 1089, 1125 (--) NVIDIA(0): H/V Polarity : +/+ This is the actual mode selected: (from xorg.0.log) (--) NVIDIA(0): 1920 x 1080 @ 60 Hz (--) NVIDIA(0): Pixel Clock : 74.18 MHz (--) NVIDIA(0): HRes, HSyncStart : 1920, 2008 (--) NVIDIA(0): HSyncEnd, HTotal : 2052, 2200 (--) NVIDIA(0): VRes, VSyncStart : 1080, 1084 (--) NVIDIA(0): VSyncEnd, VTotal : 1094, 1124 (--) NVIDIA(0): H/V Polarity : +/+ (--) NVIDIA(0): Extra : Interlaced (--) NVIDIA(0): CEA Format : 5 So my HTPC is down-converting to 1080i and then the Monitor is up-converting to 1080p How can I fix this, please?

  Read the article

• Acer Allionone Z5810 Touchscreen Issues 12.04

  - by Johannes

  I have an Acer Allionone Z5810, and I can't get the touchscreen to work after I install 12.04. Here is the lsusb output: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 0596:0508 MicroTouch Systems, Inc. Bus 001 Device 004: ID 04b8:0005 Seiko Epson Corp. Printer Bus 001 Device 005: ID 07ca:1336 AVerMedia Technologies, Inc. Bus 002 Device 003: ID 04ca:0058 Lite-On Technology Corp. Bus 002 Device 004: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 005: ID 04f2:b23f Chicony Electronics Co., Ltd xinput --list Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? Lite-On Technology Corp. Wireless Device id=9 [slave pointer (2)] ? ? Lite-On Technology Corp. Wireless Device id=10 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Power Button id=7 [slave keyboard (3)] ? Lite-On Technology Corp. Wireless Device id=8 [slave keyboard (3)] ? USB 2.0 camera id=11 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] My xorg.conf contains: nvidia-xconfig: X configuration file generated by nvidia-xconfig nvidia-xconfig: version 304.48 (buildmeister@swio-display x86-rhel47-04.nvidia.com) Sun Sep 9 21:31:39 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" InputDevice "TouchScreen" EndSection Section "Files" EndSection Section "InputDevice" Identifier "TouchScreen" Driver "microtouch" Option "Type" "finger" Option "Device" "/dev/ttyS3" Option "ScreenNo" "0" Option "MinX" "0" Option "MaxX" "16383" Option "MinY" "0" Option "MaxY" "16383" Option "SendCoreEvents" "yes" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• GPU hung when switching graphic card

  - by Lie Ryan

  I have a laptop (Dell Inspiron N4110) with a switchable graphic. $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Whistler [AMD Radeon HD 6600M Series] (rev ff) Normally, my laptop starts with both graphic cards enabled, which caused the laptop to turn very hot and the fan to become very noisy. I have been using a small script to disable the Radeon card. For some time, I'm quite happy with this arrangement. However, I have been having some issues with the Intel card (IGD), the Intel card often randomly hang when running OpenGL apps; and so I want to give the Radeon card (DIS) another chance. I have never been able to switch to the Radeon card, but recently, I found out that if I do a "delayed switching" (DDIS): # echo "DDIS" > /sys/kernel/debug/vgaswitcheroo/switch root@lieryan-dell-ubuntu:/sys/kernel/debug/vgaswitcheroo# cat switch 0:IGD:+:Pwr:0000:00:02.0 1:DIS: :Pwr:0000:01:00.0 then I logoff (i.e. to restart X), the screen switch to pseudo-tty and then it stuck there freezing. At this situation, mouse and keyboard stops working so I can't switch to another ptty. I tried ssh-ing from another computer to salvage logs (dmesg at that point) and whatnot; I found out that when freezing, the active graphic card is the AMD card: -- this is from ssh -- # cat switch 0:IGD: :Off:0000:00:02.0 1:DIS:+:Pwr:0000:01:00.0 but the GPU is apparently hung, looking at dmesg gives: ... [ 1411.649974] vga_switcheroo: client 0 refused switch [ 1411.649985] vga_switcheroo: setting delayed switch to client 1 [ 1423.911759] vga_switcheroo: processing delayed switch to 1 [ 1424.006564] fbcon: Remapping primary device, fb1, to tty 1-63 [ 1424.006799] i915: switched off [ 1424.840351] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1425.718088] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1426.622377] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1427.355683] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1428.193549] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id ... the invalid framebuffer id error is repeated for many times over ... I were able to successfully recover by switching back to the Intel card and restarting X from ssh; indicating that only the Radeon card has problems switching. System info: $ uname -a Linux lieryan-dell-ubuntu 3.0.0-14-generic #23-Ubuntu SMP Mon Nov 21 20:28:43 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric The laptop also do not have the option to set graphic card at BIOS and the proprietary driver, fglrx, also have never worked; when I installed it through jockey ("Additional Drivers"), glxinfo showed that it still being rendered by Mesa, the /sys/kernel/debug/vgaswitcheroo directory has gone missing, and the driver crashes with a traceback if I use xorg.conf to tell X to use fglrx. Anyone had any idea if it is possible to use this AMD card either with the radeon or the fglrx driver? logs: dmesg

  Read the article

• Ubuntu Sluggish and Graphics Problem after Nvidia Driver Update

  - by iam

  I just recently started using Ubuntu (12.04) since a few weeks ago and noticed that the interface is very slow and sluggish: On Dash, I have to type the entire app name and wait a few seconds before it shows up in the search box, and a bit later before it displays search result Opening new files or applications takes also quite long and awkward Dragging icons or moving app windows around is not very spontaneous too: I have to take extra attention in moving the mouse otherwise Ubuntu would not do a correct movement or might ends up doing something incorrect instead e.g. opening the windows to full screen options or move the file to different folders, which is frustrating My PC is a few years old already (1.7 GB RAM) so this could be a reason too but when I checked in System Monitor it's hardly ever consuming much memory. Plus web-surfing on Firefox is actually lightning fast (much more than Windows), so I suspect there might be something wrong with the graphics driver (mine is GeForce 7050). I checked around System Settings and found an option to update the Nvidia driver. So I tried it and restarted, as instructed. Now, I got into a big problem upon restart... as the login-screen windows (where I have to type in the password) would take several attempts to display and finally did not manage to (it'd freeze for several seconds before there's any movement again). The background screen also kept reloading several times too and at some point the screen turned black with pixelated color strips running on the bottom 1/3 of the screen, and after a long while the background screen would come up again. Eventually I'd manage to be able to access the desktop but the launcher, top menu bar and app windows border would not disappear. I searched around and found many other people have this similar problem after updating Nvidia driver too, and on some threads the suggestion is to use "killall -u $USER" in command line (it's the only thing among various online suggestions I could do, as at that point I could not access Terminal without the launcher - Ctrl-Alt-T doesn't work for me). So I did that and was able to access the desktop correctly again with launchee/menu by creating a new account. But I would still have the same problem if logging into my original account. So I just finally tried upgrading to 12.10 and now can access my original account with fully-functional desktop - the launcher, menu and windows border are all back now. However, the problem with sluggishness still remains. And now I get scared of ever having to update the Nvidia driver again! I wonder if anyone knows what's the reason that updating the Nvidia driver is causing this problem and is there a way I can update it safely in the future? I'm still not sure how to solve the problem with the sluggishness too and not sure where else to look to find a solution.

  Read the article

• Need help with a complex 3d scene (using Ogre and bullet)

  - by Matthias

  In my setup there is a box with a hole on one side, and a freely movable "stick" (or bar, tube). This stick can be inserted/moved through the hole into the box. This hole is exactly as wide as the diameter of the stick. In reality, when you would now hold the end of the stick in your hand and move the hand left/right or up/down, the other end of the stick, which is inside the box, would move into the opposite direction of your hand movement (because the stick is affixed at the pivot point where it is entering the box through the hole). (I hope you understand what I mean so far.) Now I need to simulate such a setup in a 3d program. I have already successfully developed an Ogre3d framework for this application, including bullet. But what I don't know is how I can implement in my program what I have described above. This application must include two more features: The scene camera is attached to the end of the stick that is inserted into the box. So when the user would move the mouse (to control "his" end of the stick outside the box), then the camera attached to the stick would move in the opposite direction, as described above. The stick has some length, and the user can push it further into the box, or pull it closer to him again. That means of course that the max. radius on which the end of the stick inside the box can move depends on how far the stick is pushed into the box. Thus, the more the stick is pushed into the box, the larger the max. radius of this end of the stick with the camera will be. I understand this is maybe quite a complex thing, so I don't expect any real source code here. I already have the Ogre and bullet part as said up and running, as well as a camera attached to the stick. This works fine. What I don't know though is how I can simulate the setup described above. Especially the requirement that the stick is affixed at the position of the hole on the box, where it is inserted into the box. Any ideas how I could approach to implement the described setup?

  Read the article

• New computer hangs on shutdown/reboot, how to troubleshoot?

  - by torbengb

  Summary: My machine hangs on shutdown/restart: all windows and the menu bar disappear but the desktop wallpaper remains, and it stays like that without disk activity forever (hours). It doesn't even show the shutdown screen (the one with the animated dots) where I could hit ESC and watch the shutdown text. How can I troubleshoot this? Details: I've just received a new nettop computer (Acer Aspire Revo 3700: CPU:Atom D525, GPU:Nvidia ION2). I've just made a clean install of Ubuntu 10.10 using the standard USB pendrive method. The machine boots okay and works OK including WLAN and audio, but the graphics are not OK. Ubuntu offered to install&activate the current recommended Nvidia driver, but the machine hangs on shutdown/restart which prevents the installation of the proper Nvidia driver. I have to cycle the power to reboot. I ran the Update Manager in the hope that the updates would fix the hang-up. At the end of the update-installation it asked to reboot - and got stuck just like before. I see no obvious cause of the freeze and I don't know if it's caused by graphics problems or anything else. The only USB attachment is a mouse/keyboard; I don't have any external storage attached; and I don't have any programs running (the machine freezes even when doing restart right after login). How can I determine what is causing the freeze? How can I fix this? I'm frankly rather disappointed because I bought this new machine in the hopes of getting the graphics to work, which failed miserably on my old machine, even though Ubuntu is supposed to be good with Nvidia. Being a fresh convert from Windows, I was hoping for a happier experience this time, so I'm very much looking forward to your suggestions! ... After posting this question, I see related questions in the right sidebar: this, this, and this. Don't know why these didn't show up while I composed by question. Those questions suggest some ACPI settings but I am not experienced enough to find/change those settings. I'll try the sudo shutdown -h now command when I get home and see if that works, then update this question. I did check the system BIOS but didn't see anything out of the ordinary.

  Read the article

< Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >