Search Results

Search found 29159 results on 1167 pages for 'xml configuration'.

Page 381/1167 | < Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >

• Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

  - by Maalobs

  I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

  Read the article

• Apache2 - mod_expire and mod_rewrite not working in httpd.conf - serving content from tomcat

  - by Ankit Agrawal

  Hi, I am using apache2 server running on debian which forwards all the http request to tomcat installed on same machine. I have two files under my /etc/apache2/ folder apache2.conf and httpd.conf I modified httpd.conf file to look like following. # forward all http request on port 80 to tomcat ProxyPass / ajp://127.0.0.1:8009/ ProxyPassReverse / ajp://127.0.0.1:8009/ # gzip text content AddOutputFilterByType DEFLATE text/plain AddOutputFilterByType DEFLATE text/html AddOutputFilterByType DEFLATE text/xml AddOutputFilterByType DEFLATE text/css AddOutputFilterByType DEFLATE text/javascript AddOutputFilterByType DEFLATE application/xml AddOutputFilterByType DEFLATE application/xhtml+xml AddOutputFilterByType DEFLATE application/rss+xml AddOutputFilterByType DEFLATE application/javascript AddOutputFilterByType DEFLATE application/x-javascript DeflateCompressionLevel 9 BrowserMatch ^Mozilla/4 gzip-only-text/html BrowserMatch ^Mozilla/4\.0[678] no-gzip BrowserMatch \bMSIE !no-gzip !gzip-only-text/html # Turn on Expires and mark all static content to expire in a week # unset last modified and ETag ExpiresActive On ExpiresDefault A0 <FilesMatch "\.(jpg|jpeg|png|gif|js|css|ico)$" ExpiresDefault A604800 Header unset Last-Modified Header unset ETag FileETag None Header append Cache-Control "max-age=604800, public" </FilesMatch RewriteEngine On # rewrite all www.example.com/content/XXX-01.js and YYY-01.css files to XXX.js and YYY.css RewriteRule ^content/(js|css)/([a-z]+)-([0-9]+)\.(js|css)$ /content/$1/$2.$4 # remove all query parameters from URL after we are done with it RewriteCond %{THE_REQUEST} ^GET\ /.*\;.*\ HTTP/ RewriteCond %{QUERY_STRING} !^$ RewriteRule .* http://example.com%{REQUEST_URI}? [R=301,L] # rewrite all www.example.com to example.com RewriteCond %{HTTP_HOST} ^www\.example\.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [R=301,L] I want to achieve following. forward all traffic to tomcat GZIP all the text content. Put 1 week expiry header to all static files and unset ETag/last modified header. rewrite all js and css file to certain format. remove all the query parameters from URL forward all www.example.com to example.com The problem is only 1 and 2 are working. I tried a lot with many combinations but the expire and rewrite rule (3-6) do not work at all. I also tried moving these rules to apache2.conf and .htaccess files but it didn't work either. It does not give any error but these rules are simple ignored. expires and rewrite modules are ENABLED. Please let me know what should I do to fix this. 1. Do I need to add something else in httpd.conf file (like Options +FollowSymLink) or something else? 2. Do I need to add something in apache2.conf file? 3. Do I need to move these rules to .htaccess file? If yes, what should I write in that file and where should I keep that file? in /etc/apache2/ folder or /var/www/ folder? 4. Any other info to make this work? Thanks, Ankit

  Read the article

• How to overcome Local Group Policy Editor's 1023 character limit?

  - by Louis

  I want to reorder the SSL Cipher Suite Order applied as part of KB2919355, prioritizing the forward secrecy suites above all else. Trying to do this with gpedit at Computer Configuration Administrative Templates Network SSL Configuration Settings SSL Cipher Suite Order is a problem because the new list goes over the tool's character limit. Is there anyway to overcome this limit so I don't have to keep the current priority or omit something from the list?

  Read the article

• Where is empathy-log.xsl?

  - by Tom Savage

  Conversation logs saved by Empathy are in XML format. Each one links to a stylesheet "empathy-log.xsl": <?xml-stylesheet type="text/xsl" href="empathy-log.xsl"?> I've trawled my hard drive and the web but cannot find it (there is a empathy-log-manager.xsl but this is different). Does it even exist? If there is no such file I'll create my own but I'd rather use the one provided.

  Read the article

• How do you configure apache2 to serve SVG files?

  - by Neil

  I've added these lines to /etc/apache2/apache2.conf: AddEncoding gzip .svgz AddType image/svg+xml .svg AddType image/svg+xml .svgz But SVG files still appear as broken images on my html page served by Apache. I made sure I restarted the webserver, browser and cleared the cache as well. How do you get SVG files to work with Apache2?

  Read the article

• Monitoring slow nginx/unicorn requests

  - by injekt

  I'm currently using Nginx to proxy requests to a Unicorn server running a Sinatra application. The application only has a couple of routes defined, those of which make fairly simple (non costly) queries to a PostgreSQL database, and finally return data in JSON format, these services are being monitored by God. I'm currently experiencing extremely slow response times from this application server. I have another two Unicorn servers being proxied via Nginx, and these are responding perfectly fine, so I think I can rule out any wrong doing from Nginx. Here is my God configuration: # God configuration APP_ROOT = File.expand_path '../', File.dirname(__FILE__) God.watch do |w| w.name = "app_name" w.interval = 30.seconds # default w.start = "cd #{APP_ROOT} && unicorn -c #{APP_ROOT}/config/unicorn.rb -D" # -QUIT = graceful shutdown, waits for workers to finish their current request before finishing w.stop = "kill -QUIT `cat #{APP_ROOT}/tmp/unicorn.pid`" w.restart = "kill -USR2 `cat #{APP_ROOT}/tmp/unicorn.pid`" w.start_grace = 10.seconds w.restart_grace = 10.seconds w.pid_file = "#{APP_ROOT}/tmp/unicorn.pid" # User under which to run the process w.uid = 'web' w.gid = 'web' # Cleanup the pid file (this is needed for processes running as a daemon) w.behavior(:clean_pid_file) # Conditions under which to start the process w.start_if do |start| start.condition(:process_running) do |c| c.interval = 5.seconds c.running = false end end # Conditions under which to restart the process w.restart_if do |restart| restart.condition(:memory_usage) do |c| c.above = 150.megabytes c.times = [3, 5] # 3 out of 5 intervals end restart.condition(:cpu_usage) do |c| c.above = 50.percent c.times = 5 end end w.lifecycle do |on| on.condition(:flapping) do |c| c.to_state = [:start, :restart] c.times = 5 c.within = 5.minute c.transition = :unmonitored c.retry_in = 10.minutes c.retry_times = 5 c.retry_within = 2.hours end end end Here is my Unicorn configuration: # Unicorn configuration file APP_ROOT = File.expand_path '../', File.dirname(__FILE__) worker_processes 8 preload_app true pid "#{APP_ROOT}/tmp/unicorn.pid" listen 8001 stderr_path "#{APP_ROOT}/log/unicorn.stderr.log" stdout_path "#{APP_ROOT}/log/unicorn.stdout.log" before_fork do |server, worker| old_pid = "#{APP_ROOT}/tmp/unicorn.pid.oldbin" if File.exists?(old_pid) && server.pid != old_pid begin Process.kill("QUIT", File.read(old_pid).to_i) rescue Errno::ENOENT, Errno::ESRCH # someone else did our job for us end end end I have checked God status logs but it appears CPU and Memory Usage are never out of bounds. I also have something to kill high memory workers, which can be found on the GitHub blog page here. When running a tail -f on the Unicorn logs I see some requests, but they're far and few between, when I was at around 60-100 a second before this trouble seemed to have arrived. This log also shows workers being reaped and started as expected. So my question is, how would I go about debugging this? What are the next steps I should be taking? I'm extremely baffled that the server will sometimes respond quickly, but at others time it's very slow, for long periods of time (which may or may not be peak traffic times). Any advice is much appreciated.

  Read the article

• Ububtu server 12.04 auto installation freezes at kickseeding running if ks.cfg has post scripts

  - by john206

  I'm trying to make a custom Ubuntu Server iso file. Kickstart file (ks.cfg) runs smooth when there is no %post in the file and Ubuntu installs correctly with ks configuration. Installation finishes installing base, apt, grub and It echos: Kickseed Running... and it freezes @ 0% I thought may be apt-get update doesnt work in ks file, I tried to install other apps like apache2 but no luck I have created dozen iso images and installed them in Virtual Box.I have been googling for 3 days and checked out ubuntu forums but haven't figured out the issue. I appreciate your help. This is how I made the iso image. My ks.file and txt.cfg files located in isolinux directory: root@ubuntu:/home/work mount -o loop ubuntu-12.04-amd64.iso original-iso/ rsync -a original-iso/ custom-iso/ cp ks.cfg custom-iso/isolinux/ cp txt.cfg custom-iso/isolinux/ chmod -R 777 custom-iso/ #Creating Iso image mkisofs -D -r -V “$IMAGE_NAME” -cache-inodes -J -l -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot -boot-load-size 4 -boot-info-table -o ~/ubuntu-12.04-alternate-custom-amd64.iso custom-iso/ ks.cfg #Generated by Kickstart Configurator #platform=AMD64 or Intel EM64T #System language lang en_US #Language modules to install langsupport en_US #System keyboard keyboard us #System mouse mouse #System timezone timezone America/Los_Angeles #Root password rootpw --iscrypted somethingsomething #Initial user user ubuntu --fullname "ubuntu" --iscrypted --password somethingsomething. #Reboot after installation reboot #Use text mode install text #Install OS instead of upgrade install #Use CDROM installation media cdrom #System bootloader configuration bootloader --location=mbr #Clear the Master Boot Record zerombr yes #Partition clearing information clearpart --all --initlabel #Disk partitioning information part /boot --size 128 --fstype=ext3 --asprimary part / --size 512 --fstype=ext3 --asprimary part swap --size 512 part /tmp --size 512 --fstype=ext3 part /var --size 512 --fstype=ext3 part /usr --size 4096 --fstype=ext3 part /home --size 2048 --fstype=ext3 #System authorization infomation auth --useshadow --enablemd5 #Network information network --bootproto=dhcp --device=eth0 #Firewall configuration firewall --disabled --http --ftp --ssh #X Window System configuration information xconfig --depth=32 --resolution=1024x768 --defaultdesktop=GNOME %post apt-get update mkdir /home/user txt.cfg default autoinstall label autoinstall menu label ^Install Custom Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed initrd=/install/initrd.gz quiet ks=cdrom:/isolinux/ks.cfg -- label install menu label ^Install Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed vga=788 initrd=/install/initrd.gz quiet -- label cloud menu label ^Multiple server install with MAAS kernel /install/vmlinuz append modules=maas-enlist-udeb vga=788 initrd=/install/initrd.gz quiet -- label check menu label ^Check disc for defects kernel /install/vmlinuz append MENU=/bin/cdrom-checker-menu vga=788 initrd=/install/initrd.gz quiet -- label memtest menu label Test ^memory kernel /install/mt86plus label hd menu label ^Boot from first hard disk localboot 0x80

  Read the article

• W2k8, Sybase Driver, Permissions

  - by Clustermagnet

  Trying to get a .net (32bit) app running on a Windows 2008 server. My experience in the Windows world is quite limited. Is this related to the Full/Medium trust settings? Have been Googling for quite some time. Appreciate your feedback! Seeing the following error: Required permissions cannot be acquired. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Security.Policy.PolicyException: Required permissions cannot be acquired. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [PolicyException: Required permissions cannot be acquired.] System.Security.SecurityManager.ResolvePolicy(Evidence evidence, PermissionSet reqdPset, PermissionSet optPset, PermissionSet denyPset, PermissionSet& denied, Boolean checkExecutionPermission) +7606467 System.Security.SecurityManager.ResolvePolicy(Evidence evidence, PermissionSet reqdPset, PermissionSet optPset, PermissionSet denyPset, PermissionSet& denied, Int32& securitySpecialFlags, Boolean checkExecutionPermission) +57 [FileLoadException: Could not load file or assembly 'Sybase.Data.AseClient, Version=1.155.1000.0, Culture=neutral, PublicKeyToken=26e0f1529304f4a7' or one of its dependencies. Failed to grant minimum permission requests. (Exception from HRESULT: 0x80131417)] System.Reflection.Assembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, Assembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection) +0 System.Reflection.Assembly.nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, Assembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection) +43 System.Reflection.Assembly.InternalLoad(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) +127 System.Reflection.Assembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) +142 System.Reflection.Assembly.Load(String assemblyString) +28 System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) +46 [ConfigurationErrorsException: Could not load file or assembly 'Sybase.Data.AseClient, Version=1.155.1000.0, Culture=neutral, PublicKeyToken=26e0f1529304f4a7' or one of its dependencies. Failed to grant minimum permission requests. (Exception from HRESULT: 0x80131417)] System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) +613 System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() +203 System.Web.Configuration.CompilationSection.LoadAssembly(AssemblyInfo ai) +105 System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) +178 System.Web.Compilation.WebDirectoryBatchCompiler..ctor(VirtualDirectory vdir) +163 System.Web.Compilation.BuildManager.BatchCompileWebDirectoryInternal(VirtualDirectory vdir, Boolean ignoreErrors) +53 System.Web.Compilation.BuildManager.BatchCompileWebDirectory(VirtualDirectory vdir, VirtualPath virtualDir, Boolean ignoreErrors) +175 System.Web.Compilation.BuildManager.CompileWebFile(VirtualPath virtualPath) +86 System.Web.Compilation.BuildManager.GetVPathBuildResultInternal(VirtualPath virtualPath, Boolean noBuild, Boolean allowCrossApp, Boolean allowBuildInPrecompile) +261 System.Web.Compilation.BuildManager.GetVPathBuildResultWithNoAssert(HttpContext context, VirtualPath virtualPath, Boolean noBuild, Boolean allowCrossApp, Boolean allowBuildInPrecompile) +101 System.Web.Compilation.BuildManager.GetVirtualPathObjectFactory(VirtualPath virtualPath, HttpContext context, Boolean allowCrossApp, Boolean noAssert) +126 System.Web.Compilation.BuildManager.CreateInstanceFromVirtualPath(VirtualPath virtualPath, Type requiredBaseType, HttpContext context, Boolean allowCrossApp, Boolean noAssert) +62 System.Web.UI.PageHandlerFactory.GetHandlerHelper(HttpContext context, String requestType, VirtualPath virtualPath, String physicalPath) +33 System.Web.UI.PageHandlerFactory.GetHandler(HttpContext context, String requestType, String virtualPath, String path) +37 System.Web.MaterializeHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +307 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +155 Version Information: Microsoft .NET Framework Version:2.0.50727.4959; ASP.NET Version:2.0.50727.4955

  Read the article

• How to achieve zero down time

  - by Hiral Lakdavala

  For an application we want to achieve zero database and application down time using Active Active configuration. Our dB is Oracle Following are my questions: How can we achieve active active configuration in Oracle? Will introducing Cassandra/HBase(or any other No SQL dbs) cloud help in zero downtime or it is only for fast retrieval of data in a large db? Any other options? Thanks and Regards, Hiral

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated. Update (2011-06-26) After failing to solve the problem, I resorted to paid Microsoft support. They were unable to solve the problem. Since then I have implemented a solution based on Linux that is working quite well. I will attempt to evaluate any proposed answers as best I can, but current configurations and time constraints will make this slow...

  Read the article

• can not connect through SCP, but SSH connections works

  - by Joe Cabezas

  i am trying to connect to my server to transfer file using scp: $ scp -v -r -P <port> <user>@<host>:~/dir/ dir/ this is the output: OpenSSH_5.2p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /Users/joe/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: Connecting to <host> [<host>] port <port>. debug1: Connection established. debug1: identity file /Users/joe/.ssh/identity type -1 debug1: identity file /Users/joe/.ssh/id_rsa type -1 debug1: identity file /Users/joe/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host but connecting via SSH works fine: $ ssh <user>@<host> -p <port> <user>@<host>'s password: <user>@<host>:~$ OK what can be wrong with this? my /etc/ssh/sshd_config file on the host is: # Package generated configuration file # See the sshd_config(5) manpage for details # What ports, IPs and protocols we listen for Port <port> # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel INFO # Authentication: LoginGraceTime 120 PermitRootLogin yes StrictModes yes RSAAuthentication yes PubkeyAuthentication no #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords #PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM yes

  Read the article

• How to configure apache and mod_proxy_ajp in order to forward ssl client certificate

  - by giovanni.cuccu

  I've developed a java application that need a ssl client certificate and in the staging environment with apache 2.2 and mod_jk it is working fine. In production the configuration is not using mod_jk but mod_proxy_ajp. I'm looking for an apache configuration example that configure ssl and mod_proxy_ajp for sending the ssl client certificate to the java application server (which listens with the ajp protocol). Thanks a lot

  Read the article

• Add DNS record for subdomain on different web hotel

  - by Martin Wiboe

  Hi, I am quite inexperienced with DNS, so this might be simple. Our main domain foo.com is hosted at provider A. Now, we would like to host bar.foo.com at some other provider B - they have the domain set up with them, so I figure that I can do this by somehow adding the nameserver at provider B to the DNS configuration at provider A. The current DNS config is as follows: http://imgur.com/kG099.png How can I add the new subdomain to this configuration? Regards, Martin Wiboe

  Read the article

• Issues with static IP (Ubuntu Server 10.04)

  - by letseatfood

  I am following this tutorial for setting up a testing server for my web development projects. When I attempt setting up a static IP address (using the configuration below), I receive the error "ping: unknown host www.google.com" when I attempt using ping. auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 Ping works fine when the configuration is: auto eth0 iface eth0 inet static I am a novice to server setup and administration.

  Read the article

• Cannot make BartPE CD - how restore DriveImageXML image?

  - by CChriss

  I have a Windows Vista laptop that won't boot at all. On the D: drive I have DriveImage XML images of C: drive, but I don't have a BartPE boot CD and I don't have a Vista install CD. How can I image the C: using the images on D: if I can't make a BartPE CD because I can't boot to Windows? Is there a BartPE (with DriveImage XML plugin) iso I can download from somewhere, or what can I do? Thanks.

  Read the article

• Unable to use "Manage Content and Structure" after removing Project server form the SharePoint farm.

  - by Brian

  We're no longer using Office Project Server, and I've removed it from the farm in which it was installed. However, now that it's been removed, I am unable to access the "Manage Content and Structure" link on some of our SharePoint sites. I get an error indicating that SharePoint Failed to find the XML file at location '12\Template\Features\PWSCommitments\feature.xml' Anyone have an idea how to fix this?

  Read the article

• Ubuntu 12.10 Clock is wrong

  - by mardavi

  I have an issue with Ubuntu Quantal, as it shows the wrong time. It is completely messy, the right time from time.is now is 09.43 and my clock shows 17.48. I am using ntp service and I already checked the timezone and it is correct. I also checked the hardware clock through sudo hwclock --showsudo dpkg-reconfigure tzdata and this is right too. I also tried sudo dpkg-reconfigure tzdata but with bad luck. What else can I try? As asked, here my /etc/ntp.conf # /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for help driftfile /var/lib/ntp/ntp.drift # Enable this if you want statistics to be logged. #statsdir /var/log/ntpstats/ statistics loopstats peerstats clockstats filegen loopstats file loopstats type day enable filegen peerstats file peerstats type day enable filegen clockstats file clockstats type day enable # Specify one or more NTP servers. # Use servers from the NTP Pool Project. Approved by Ubuntu Technical Board # on 2011-02-08 (LP: #104525). See http://www.pool.ntp.org/join.html for # more information. server 0.ubuntu.pool.ntp.org server 1.ubuntu.pool.ntp.org server 2.ubuntu.pool.ntp.org server 3.ubuntu.pool.ntp.org server time.nist.gov # Use Ubuntu's ntp server as a fallback. server ntp.ubuntu.com # Access control configuration; see /usr/share/doc/ntp-doc/html/accopt.html for # details. The web page <http://support.ntp.org/bin/view/Support/AccessRestrictions> # might also be helpful. # # Note that "restrict" applies to both servers and clients, so a configuration # that might be intended to block requests from certain clients could also end # up blocking replies from your own upstream servers. # By default, exchange time with everybody, but don't allow configuration. restrict -4 default kod notrap nomodify nopeer noquery restrict -6 default kod notrap nomodify nopeer noquery # Local users may interrogate the ntp server more closely. restrict 127.0.0.1 restrict ::1 # Clients from this (example!) subnet have unlimited access, but only if # cryptographically authenticated. #restrict 192.168.123.0 mask 255.255.255.0 notrust # If you want to provide time to your local subnet, change the next line. # (Again, the address is an example only.) #broadcast 192.168.123.255 # If you want to listen to time broadcasts on your local subnet, de-comment the # next lines. Please do this only if you trust everybody on the network! #disable auth #broadcastclient In addition, the ntp service was not running when I turned on my laptop today.

  Read the article

• Apache2 - mod_expire and mod_rewrite not working in httpd.conf - serving content from tomcat

  - by Ankit Agrawal

  I am using apache2 server running on debian which forwards all the http request to tomcat installed on same machine. I have two files under my /etc/apache2/ folder apache2.conf and httpd.conf I modified httpd.conf file to look like following. # forward all http request on port 80 to tomcat ProxyPass / ajp://127.0.0.1:8009/ ProxyPassReverse / ajp://127.0.0.1:8009/ # gzip text content AddOutputFilterByType DEFLATE text/plain AddOutputFilterByType DEFLATE text/html AddOutputFilterByType DEFLATE text/xml AddOutputFilterByType DEFLATE text/css AddOutputFilterByType DEFLATE text/javascript AddOutputFilterByType DEFLATE application/xml AddOutputFilterByType DEFLATE application/xhtml+xml AddOutputFilterByType DEFLATE application/rss+xml AddOutputFilterByType DEFLATE application/javascript AddOutputFilterByType DEFLATE application/x-javascript DeflateCompressionLevel 9 BrowserMatch ^Mozilla/4 gzip-only-text/html BrowserMatch ^Mozilla/4\.0[678] no-gzip BrowserMatch \bMSIE !no-gzip !gzip-only-text/html # Turn on Expires and mark all static content to expire in a week # unset last modified and ETag ExpiresActive On ExpiresDefault A0 <FilesMatch "\.(jpg|jpeg|png|gif|js|css|ico)$" ExpiresDefault A604800 Header unset Last-Modified Header unset ETag FileETag None Header append Cache-Control "max-age=604800, public" </FilesMatch RewriteEngine On # rewrite all www.example.com/content/XXX-01.js and YYY-01.css files to XXX.js and YYY.css RewriteRule ^content/(js|css)/([a-z]+)-([0-9]+)\.(js|css)$ /content/$1/$2.$4 # remove all query parameters from URL after we are done with it RewriteCond %{THE_REQUEST} ^GET\ /.*\;.*\ HTTP/ RewriteCond %{QUERY_STRING} !^$ RewriteRule .* http://example.com%{REQUEST_URI}? [R=301,L] # rewrite all www.example.com to example.com RewriteCond %{HTTP_HOST} ^www\.example\.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [R=301,L] I want to achieve following. forward all traffic to tomcat GZIP all the text content. Put 1 week expiry header to all static files and unset ETag/last modified header. rewrite all js and css file to certain format. remove all the query parameters from URL forward all www.example.com to example.com The problem is only 1 and 2 are working. I tried a lot with many combinations but the expire and rewrite rule (3-6) do not work at all. I also tried moving these rules to apache2.conf and .htaccess files but it didn't work either. It does not give any error but these rules are simple ignored. expires and rewrite modules are ENABLED. Please let me know what should I do to fix this. 1. Do I need to add something else in httpd.conf file (like Options +FollowSymLink) or something else? 2. Do I need to add something in apache2.conf file? 3. Do I need to move these rules to .htaccess file? If yes, what should I write in that file and where should I keep that file? in /etc/apache2/ folder or /var/www/ folder? 4. Any other info to make this work? Thanks, Ankit

  Read the article

• Unable to use "Manage Content and Structure" after removing Project server form the SharePoint farm

  - by Brian

  We're no longer using Office Project Server, and I've removed it from the farm in which it was installed. However, now that it's been removed, I am unable to access the "Manage Content and Structure" link on some of our SharePoint sites. I get an error indicating that SharePoint Failed to find the XML file at location '12\Template\Features\PWSCommitments\feature.xml' Anyone have an idea how to fix this?

  Read the article

• Lync Edge and Exchange Server: how to have access to my exchange mailbox from external network and also to the OWA

  - by Garcia Julien

  I've some problem in the configuration of Exchange 2010. My topology is like that: Server1 = Domain Controller Server2 = Exchange Server Server3 = Lync Server Server4 = Lync Edge Our public address (the one accessible by outside world) is directed to Server4. I would like to have access to my exchange mailbox from external network and also to the OWA. Could you help me in the configuration of thoses servers? Thank in advance Julien

  Read the article

• Can't upgrade my Ubuntu server, it gets stuck on openjdk-6-jre-headless

  - by Jean-Nicolas Boulay Desjardins

  I am using Ubuntu Server. When I do: apt-get upgrade it gets stuck on: Setting up openjdk-6-jre-headless (6b20-1.9.7-0ubuntu1) ... Why? And what can I do to stop it? I tried removing it with apt-get... I get this error: E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. So then I tried this: dpkg --purge openjdk-6-jre-headless I got this: dpkg: dependency problems prevent removal of openjdk-6-jre-headless: openjdk-6-jre-lib depends on openjdk-6-jre-headless (>= 6b17). ca-certificates-java depends on openjdk-6-jre-headless (>= 6b16-1.6.1-2) | java6-runtime-headless; however: Package openjdk-6-jre-headless is to be removed. Package java6-runtime-headless is not installed. Package openjdk-6-jre-headless which provides java6-runtime-headless is to be removed. ca-certificates-java depends on openjdk-6-jre-headless (>= 6b16-1.6.1-2) | java6-runtime-headless; however: Package openjdk-6-jre-headless is to be removed. Package java6-runtime-headless is not installed. Package openjdk-6-jre-headless which provides java6-runtime-headless is to be removed. dpkg: error processing openjdk-6-jre-headless (--purge): dependency problems - not removing Errors were encountered while processing: openjdk-6-jre-headless The thing is I think my DB is using it... Not sure... I am using Cassandra with Thrift... Yes, it's getting a bit more complex... # dpkg --configure -a I get: dpkg: dependency problems prevent configuration of openjdk-6-jre: openjdk-6-jre depends on openjdk-6-jre-headless (>= 6b20-1.9.7-0ubuntu1); however: Package openjdk-6-jre-headless is not configured yet. dpkg: error processing openjdk-6-jre (--configure): dependency problems - leaving unconfigured Processing triggers for libc-bin ... ldconfig deferred processing now taking place dpkg: dependency problems prevent configuration of libaccess-bridge-java: libaccess-bridge-java depends on default-jre | openjdk-6-jre | sun-java6-jre; however: Package default-jre is not installed. Package openjdk-6-jre is not configured yet. Package sun-java6-jre is not installed. dpkg: error processing libaccess-bridge-java (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of icedtea-6-jre-cacao: icedtea-6-jre-cacao depends on openjdk-6-jre-headless (= 6b20-1.9.7-0ubuntu1); however: Package openjdk-6-jre-headless is not configured yet. dpkg: error processing icedtea-6-jre-cacao (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libaccess-bridge-java-jni: libaccess-bridge-java-jni depends on libaccess-bridge-java (>= 1.26.2-5); however: Package libaccess-bridge-java is not configured yet. dpkg: error processing libaccess-bridge-java-jni (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: openjdk-6-jre libaccess-bridge-java icedtea-6-jre-cacao libaccess-bridge-java-jni Thanks again for any help.

  Read the article

• How to configure apache and mod_proxy_ajp in order to forward ssl client certificate

  - by giovanni.cuccu

  Hi, I've developed a java application that need a ssl client certificate and in the staging environment with apache 2.2 and mod_jk it is working fine. In production the configuration is not using mod_jk but mod_proxy_ajp. I'm looking for an apache configuration example that configure ssl and mod_proxy_ajp for sending the ssl client certificate to the java application server (which listens with the ajp protocol). Thanks a lot

  Read the article

• HP DL380 G7 Disk swap to a HP DL380 G6

  - by rnuno

  The HP DL380 G7 has 3 SAS disks in RAID 5 configuration. I need to change that server to another task and instead of make a clean install on the HP DL380 G6 can i just swap the 3 disks from HP DL380 G7 to the HP DL380 G6? I expect some driver issues maybe on the OS itself because the processor is different. They both use Smart Array P410i, if i power down the machines swap the disk by the same order will the RAID 5 configuration remain and the OS will boot?

  Read the article

• Debian + ProFTPD + LDAP Incorrect Password Issue

  - by Tristan Hall

  I have the LDAP configuration configured for ProFTPD and I have modified the modules.conf file to include the LDAP module. However, every time I login with FileZilla I get 530 Login Incorrect. It does this for all users except those whose passwords are defined locally as well as in LDAP. The exact same setup works fine on my CentOS server and I've already tried re-installing it after purging the configuration files.

  Read the article

• Odd squid transparent redirect behavior

  - by EMiller

  This is the first time I've set up squid. It's running a redirect script that does some text search/replace on html pages, and then saves them to a location on the same machine on the nginx path - then issues the redirect to that URL (it's an art project :D). The relevant lines in squid.conf are http_port 3128 transparent redirect_program /etc/squid/jefferson_redirect.py The jefferson_redirect.py script is based on this script: http://gofedora.com/how-to-write-custom-redirector-rewritor-plugin-squid-python/ The issue: I'm getting strange http redirect behavior. For example, here is the normal request/response from a PHP script that issues a header("Location:"); - a 302 redirect: http://redirector.mysite.com/?unicmd=g+yreka GET /?unicmd=g+yreka HTTP/1.1 Host: redirector.mysite.com User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-1.fc12 Firefox/3.5.9 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive HTTP/1.1 302 Found Date: Tue, 13 Apr 2010 05:15:43 GMT Server: Apache X-Powered-By: PHP/5.2.11 Location: http://www.google.com/search?q=yreka Content-Type: text/html Vary: User-Agent,Accept-Encoding Content-Encoding: gzip Content-Length: 2108 Keep-Alive: timeout=3, max=100 Connection: Keep-Alive Here's what it looks like when running through the squid proxy (note that "redirector.mysite.com" is not the site running squid or nginx): http://redirector.mysite.com/?unicmd=g+yreka GET /?unicmd=g+yreka HTTP/1.1 Host: redirector.mysite.com User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-1.fc12 Firefox/3.5.9 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Proxy-Connection: keep-alive If-Modified-Since: Tue, 13 Apr 2010 05:21:02 GMT HTTP/1.0 200 OK Server: nginx/0.7.62 Date: Tue, 13 Apr 2010 05:21:10 GMT Content-Type: text/html Content-Length: 17865 Last-Modified: Tue, 13 Apr 2010 05:21:10 GMT Accept-Ranges: bytes X-Cache: MISS from jefferson X-Cache-Lookup: HIT from jefferson:3128 Via: 1.1 jefferson:3128 (squid/2.7.STABLE6) Connection: keep-alive Proxy-Connection: keep-alive It is basically working - but the URL http://redirector.mysite.com/?unicmd=g+yreka remains unchanged, while displaying the google page (mostly broken as it's using URLs relative to redirector.mysite.com) I've experienced a similar thing with google results pages: when clicking to another page from google, I get a google URL, with the other site's content. Sorry for the long post - many thanks if you've read this far! Any ideas?

  Read the article

< Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >