Search Results

Search found 20822 results on 833 pages for 'remote desktop gateway'.

Page 388/833 | < Previous Page | 384 385 386 387 388 389 390 391 392 393 394 395  | Next Page >

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• WAMP starts Apache or Mysql, but not both?

  - by ladenedge

  When I install WAMP, the Apache and Mysql services are set to run as the LocalService user and all works well. However, because I need to access remote UNC paths in my PHP code, I need to run at least Apache as a user that exists on both the local host and the remote host - I'll call him WampUser. When both Apache and Mysql are set to start as WampUser, I cannot start both at the same time. If both are stopped, I can start either successfully. When I attempt to start the other, I get Error 1053: The service did not respond to the start or control request in a timely fashion. This error appears immediately - there is no timeout. When at least one of the services is set to start as LocalService, both start fine. I can, therefore, solve my problem by setting Apache to WampUser and Mysql to LocalService, but I'm more interested in why this is happening in the first place. I'm especially curious because this situation does not occur on other servers - something I've done to this server has made these two services exclusive when running as the same user. Here are some miscellaneous data points: I am using Windows Server 2003. I've provided recursive Full Control to the C:\wamp directory for WampUser. Nothing appears in the event log after the service fails. No log entries appear in either the Mysql log or the Apache error log. Neither application appears in the process list when the appropriate service is stopped. Any ideas?

  Read the article

• Security in shared hosting vs VPS 'virtual appliances'

  - by Pedro Loureiro

  I have to change my hosting provider. Right now I have a shared hosting account but I'm considering trying the LAMP stack appliance from turnkeylinux.org. I'm very comfortable with using linux, I've been using it for a long time. I have no problem ssh'ing into remote machines and do whatever I have to do (coding, reading logs, moving files, deploying, etc). The problem is that none of those tasks have involved securing the server/firewall. My experience has been as a desktop user or developer deploying apps/files in remote servers. Ignoring the security in the application logic (read: any scripts, frameworks, websites I might have created or installed) - I'm worried about things like base configuration of deamons, firewall, ports, executable scripts being readable from the outside and whatnot. My question is: how do you compare the (expected) out of the box security of the LAMP stack from turnkey and the (expected) security of a "regular" shared hosting provider? I was hoping to find some guides with a list of steps to do to protect my server but the only documentation I found was simply referring to ubuntu's documentation.

  Read the article

• How to wake from screensaver directly to the login screen in Ubuntu

  - by torbengb

  (a.k.a. How to switch users without entering password, part II) (see part I) I've got Ubuntu 9.10 with a user account for my wife, and one for myself. "Wake-from-screensaver" should result in "choose user" without having to enter any password. I know how to do that in Windows, but I'm not good with Linux (yet). Part of this was answered in my earlier question which helped me get past the login screen without passwords (after booting, and after choosing "switch user"), but once the screensaver kicks in and I wake it up again, the system does not present the "choose user" screen. Instead, it either turns off the screensaver and presents the desktop of the most recent user, or (if the screensaver is set to lock the screen) prompt for the user's password (which can be handily surpassed by clicking the "switch user" button and choosing the same user again). So, the login ("choose user") screen has been dealt with. How do I make the (any) screensaver return to the login screen at wake, rather than to the current user's desktop? Windows can do this, I'm sure Linux can too - but how?

  Read the article

• Custom authentication method for GDM

  - by FMC

  I am trying to find a way of authenticating users on public computers through GDM, but I have a few things to be taken in account. The users do not have a login/password, they only thing they are given is a string. This string is unique and will allow us to identify them. You can see this string as a login without a password. The users must be present in a remote database The users must have the rights to login on the computer they are on at that time. A remote database would check if a booking on the computer had been set for that time by that user. Or if no booking had been made, allow to login. A default user id/home/gid has to be set to the user once logged in I have found ways to deal with most of those requirements, but not altogether. PAM looks nice to set up a custom way of checking if the user booked its computer. NSS MySQL looks nice to set up the environment. Would you know how to set up the environment by myself using a custom PAM module (using pam_python would be preferred)? Or any other method that could help me? Thanks in advance!

  Read the article

• DNS Does Not Register at Off-site Locations

  - by Russ Warren

  First of all, let me give you the specifics of our setup: Windows Small Business Server 2008 Domain w/ all applicable updates on the DC The DC does DHCP for the main site The DC does DNS for all sites 3 sites including our headquarters where the DC is located All sites are connected through OpenVPN SSL tunnels terminated by an Untangle box at each site The 2 remote sites us the Untangle box as a DHCP server for their subnet, which assigns the DC as the primary DNS server Collection of Windows XP and Windows 7 workstations connected to the domain Here's the issue: All of the workstations at the main site register with the DNS server on the domain controller fine. As they grab an IP from the DHCP server, it updates the DNS server with the new host record. I have 2 systems (each at different remote sites) that fail to register with the DNS server. I've attempted the following troubleshooting steps: Confirmed the network adapter is using the DC as a DNS server Confirmed 2-way traffic is possible between DC and workstation Verified the "Register with DNS server" setting was checked in the adapter properties Attempted ipconfig /registerdns and received no errors For the time being, I have setup a DHCP reservation for these systems and manually created a host record. This seems to work fine, but I need a solution for any new systems that go out there.

  Read the article

• VMware ARP/Mac Networking

  - by Ross Wilson

  Hi Guys, I am very interested in how VMware networking works. I have scoured the VMware website and read their data sheets, this has given me some basic knowledge. I now have some questions. Lets assume that we have a physical server running the VMware hypervisor. The physical server is running a Virtual Machine. The physical box has one physical NIC. The NIC is connected to a switch, as so is a desktop client. Now, this is where my first question lies. The VM has an IP address: 192.168.1.1. How do desktop clients on the network communicate with this VM? So, the client pings 192.168.1.1. The ping packet is sent to the switch. The switch checks its MAC address table and sees that 192.168.1.1 is associated with the MAC address of the physical NIC. Correct? I then assume that the ping packet is sent to the server's physical NIC, where the hypervisor routes the packet to the VM thats using 192.168.1.1? Please could you give me a run down as to how VM networking works? Many thanks, Ross

  Read the article

• My EliteBook is not auto picking 1080p for external monitor, poor display on forcing

  - by Griever

  I'm connecting my Samsung LED S22A300B to my HP EliteBook 6930p through VGA out. Laptop has Intel 4500MHD video card. I have latest drivers installed for both card and monitor. Only 800x600 and 1024x768 are shown. A lot of other people get this problem when they use it with docking station as discussed here. But I am not using any docking station. The monitor works great with my desktop though. As advised on the aforementioned page, one of the things I tried was to force the resolution using Intel's "custom resolution" feature. I installed PowerStrip on my desktop and copied advanced timing values(front/back porch,sync width, etc.) from there and then used the same values while defining a custom resolution in my laptop's Intel graphics utility. As a result, I got the 1080p resolution but the display is poor. Text has some weird colored shadow and sometimes on images too. What should I do?

  Read the article

• SSRS 2005 inaccessible after install

  - by Gabriel Guimarães

  Hi I've just installed SQL 2005 and Database Engine is ok, however I can't access it for nothing. When I go to http://localhost/reports I get this prompt for a username and password and it fails with 401.1. When I tried to disable kerberos on the virtual directories, nothing changed. I've tried changing the auth to anonymous and get: Internet Explorer cannot display the webpage. When I access from another machine, I get the prompt only once and get this error. Internet Explorer cannot display the webpage. Can't access this with IE or SSMS 2005. If I try to access with Management Studio i get this error: TITLE: Microsoft SQL Server Management Studio The underlying connection was closed: An unexpected error occurred on a receive. (Microsoft.SqlServer.Management.UI.RSClient) ADDITIONAL INFORMATION: Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. (System) An existing connection was forcibly closed by the remote host (System) BUTTONS: OK By the way the server info: its a Win 2003 R2 Standard with IIS 6 Can't seem to understand this. Does anyone have a hint?

  Read the article

• How to activate Win XP from Windows 7 compatibility mode on MacOS Parallels 5

  - by Ben Hammond

  I am running Parallels Desktop 5.0.9344 for Mac. I am running Mac OS 10.6.3 10D2094 I have bought a retail copy of Window 7 professional specifically because I need the XP compatibility. Windows 7 is installed and working. I have problems with the XP activation Windows7 'Virtual PC' does not run under Parallels (strange error about Server Execution failed 0x80080005). I have used the Parallels Transporter to convert the "Windows XP Mode Base.vhd" file into a parallels Virtual Machine. This copy of XP now starts normally, however it records itself as unregistered. There was a KEY.txt file in the same directory as the .vhd file; although this file contains a valid-looking activation key, it does not appear to activate the instance of XP. I have also tried to enter the Win7 activation key; this does not work either. I have tried calling the two phone numbers; an automated system asked me to enter 56 digits through the telephone and then accused me of being a pirate. I believe it may be possible to install Win7 via Bootcamp, start WinXP under Virtual PC, activate it and then import this activated .vhd into Parallels; but that seems a long way round, and is far from certain. What can I do to get WinXP running under Mac Parallels Desktop ?

  Read the article

• mac terminal run a file of commands

  - by Ilan Tal

  I am coming from Linux and trying to get a Mac to do what I want it to do. The question is what is the best tool to use. I want to mount (unmount) several remote disks. If I go into a terminal I can do the trick by mount -t smbfs //username:pass@addr /Users/me/RemoteDisks/mnt1 Since I want to mount several disks I would like to put all of the information into a file, store it in Documents/subfolder and make a link to it on the desktop (or somewhere better, if there is a better place). At the moment I have manually run the appropriate command in the terminal and the remote disk is mounted and I see its contents. What I need is a one click method to run a file to mount all the disks. I tried Apple script but that didn't like my commands. I don't know exactly what it is expecting to see and perhaps Apple script is the wrong tool. I have no problems in Linux, but the Mac is new to me and I don't know what I should be using. Thanks, Ilan

  Read the article

• Samba and Windows 7

  - by John Gaughan

  I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

  Read the article

• Win7 Aero disabled due to mirror drivers following TightVNC use, cannot re-enable

  - by me_and

  I recently installed TightVNC, and used it to access my desktop from my phone. When I did so, my desktop reported that Aero had been disabled due to an application being run that didn't support it. I now cannot re-enable Aero, despite having closed the TightVNC server (and indeed having rebooted a number of times since). Windows 7 troubleshooting reports the following: Close programs using mirror drivers To allow Aero effects to be displayed, close any programs that use mirror drivers (a type of display driver), such as Windows Remote Assistance and Windows Live Mesh. The troubleshooting system appears to attempt to automatically fix that, but fails. I can see nothing in the task manager that obviously uses mirror drivers; in particular, I can see nothing that looks like TightVNC in there. Starting and exiting TightVNC makes no difference. Google has turned up nothing that looks useful so far, either, although my Google-fu isn't great and I may just be searching for the wrong things. There's another question that reports the same problem, caused by LogMeIn rather than TightVNC, but the solution listed there doesn't work—TightVNC doesn't install LogMeIn mirror drivers, for obvious reasons.

  Read the article

• Shared printer stops working on clients but not host computer

  - by Tony

  I have a Brother MFC-7420 USB all-in-one laser printer. It is plugin via USB to my Windows 7 x64 machine. I have it shared to a few users on my home network. My wife's laptop running Vista x64 can normally print fine to the printer. However it seems that every day or two, when she pushes print on a something it just sits in her laptop's print queue and never makes it to my desktop. The only thing that seems to fix this is if she restarts her laptop. Not a big deal but this problem is sort of annoying. I don't know if this affects but the laptop is put into hibernate at night and I turn my desktop off at night. Does anyone know why this happens and if there is something easy to do to fix the problem besides restart the computer? EDIT: I was thinking that maybe my wife's laptop loses its connection to the printer. Is there a way to reset a connection to a shared printer? Or maybe reauth with the printer?

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by Develop7

  Intro I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 Problem But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator screams "Logon failure" upon connect attempt, and, respectively, fails to connect. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d Question So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by develop7

  Preface: I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator tells "Logon failure" upon connect attempt. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• Start and shutdown tomcat via ssh

  - by bxshi

  Updated I find out that the path of jdk it using is wrong. eval: 1: /opt/Java/jdk1.6.0_25/jre/bin/java: not found the Java should be lower case java, how is that happen? When I run this script directly on server, it is just okay. I'm trying to start or shutdown tomcat via a remote client. On my server, I've got 3 different tomcat: tomcat1, tomcat2, and tomcat3. Firstly, I've tried to run tomcat_path/bin/shutdown.sh to stop it via ssh, and the command is ssh [email protected] "cd /home/jake/tomcat2/bin;exec bash ./shutdown.sh" both " and ' are tried, but do not work, the output is eval: 1: /opt/Java/jdk1.6.0_25/jre/bin/java: not found it seems that the shell script runs on my local client, because on server it has this file. Is there any way to run a shell script on remote server correctly? updated I've run ssh [email protected] "sh -x /home/jake/tomcat/bin/shutdown.sh > /home/jake/tomcat.log 2>&1" and the output in tomcat.log is : + PRG=/home/jake/tomcat/bin/shutdown.sh + [ -h /home/jake/tomcat/bin/shutdown.sh ] + dirname /home/jake/tomcat/bin/shutdown.sh + PRGDIR=/home/jake/tomcat/bin + EXECUTABLE=catalina.sh + [ ! -x /home/jake/tomcat/bin/catalina.sh ] + exec /home/jake/tomcat/bin/catalina.sh stop eval: 1: /opt/Java/jdk1.6.0_25/jre/bin/java: not found

  Read the article

• Connect over WiFi to SQL Server from another computer

  - by Bronzato

  I tried to connect over WiFi to SQL Server with SQL Server Management Studio from another computer, but it failed. I have a computer with Windows 7 & SQL Server 2008 (lets say the server computer). Next to it I have a freshly installed computer with Windows 7 & SQL Server Management Studio (let's say the client computer). What I did on the server computer: Configure firewall by enabling port 1433 Enabled network protocols (TCP/IP) inside SQL Server Configuration Manager Checked Allow remote connections to this server in server properties in the SQL Server Management application. Started SQL Server Browser Restarted services (SQL Server Browser is stopped at this point, but I don't think it is necessary. Is it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to SQL Server on my server computer. Ok, something new with this problem: Until now, I successfully connected to my "server computer" with Management Studio. What I did is type the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of SQL server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name. Now my new challenge is to be successful in connecting my VB6 application to this remote database located on my "server computer". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's going wrong?

  Read the article

• OS X won't see Windows 7 in network (and vice versa)

  - by meds

  I've enabled SMB sharing in OS X Lion and have added folders to share, it says 'Windows Sharing: On' with a green circle next to it (from the sharing window) and that to access the volume I will need to to go to \\192.168.0.17. It also says that the OS X should be visible as 'macbook' in the network. Both my WIndows 7 and OS X are connected to the same network, yet when I try to go to \\192.168.0.17 or from the Mac try to go to my Windows system (smb://192.168.0.6) the two OSs don't see each other. Any ideas why? Attempting to ping the Mac from Windows results in this output in the command prompt: Pinging 192.168.0.17 with 32 bytes of data: Reply from 192.168.0.6: Destination host unreachable. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.17: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), ipconfig in Windows is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::8918:efd1:b05c:890f%21 IPv4 Address. . . . . . . . . . . : 192.168.0.6 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::98ab:63fc:3c07:d837%13 IPv4 Address. . . . . . . . . . . : 192.168.74.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::80ff:c575:7b50:3a10%14 IPv4 Address. . . . . . . . . . . : 192.168.21.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{2E97D0AE-9E18-4072-AC23-1979BA0DCB79}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{E260CE43-E9A7-4DE0-A88E-4EAFF68ACDDB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{A5130812-59CE-4DDF-9C35-9433BCED9831}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{134BCAE7-CFFF-4A98-8DA0-3708806AABEB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{8D9E3B8F-161C-4ACE-B211-3EDD694416B2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : in OS X: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4> ether c8:2a:14:01:24:c1 media: autoselect (none) status: inactive en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether e0:f8:47:0c:fe:04 inet6 fe80::e2f8:47ff:fe0c:fe04%en1 prefixlen 64 scopeid 0x5 inet 192.168.0.17 netmask 0xffffff00 broadcast 192.168.0.255 media: autoselect status: active p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304 ether 02:f8:47:0c:fe:04 media: autoselect status: inactive fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 70:cd:60:ff:fe:d8:f1:32 media: autoselect <full-duplex> status: inactive

  Read the article

• Can't login via ssh after upgrading to Ubuntu 12.10

  - by user42899

  I have an Ubuntu 12.04LTS instance on AWS EC2 and I upgraded it to 12.10 following the instructions at https://help.ubuntu.com/community/QuantalUpgrades. After upgrading I can no longer ssh into my VM. It isn't accepting my ssh key and my password is also rejected. The VM is running, reachable, and SSH is started. The problem seems to be about the authentication part. SSH has been the only way for me to access that VM. What are my options? ubuntu@alice:~$ ssh -v -i .ssh/sos.pem [email protected] OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/ubuntu/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to www.hostname.com [37.37.37.37] port 22. debug1: Connection established. debug1: identity file .ssh/sos.pem type -1 debug1: identity file .ssh/sos.pem-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: RSA 33:33:33:33:33:33:33:33:33:33:33:33:33:33 debug1: Host '[www.hostname.com]:22' is known and matches the RSA host key. debug1: Found key in /home/ubuntu/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: .ssh/sos.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentications that can continue: publickey,password Permission denied, please try again.

  Read the article

• Domain joined computer unable to access servers through VPN

  - by kscott

  Our servers are in a virtual off site hosting center, our office has a vpn connection to the data center, but for reasons I don't understand we also have to connect to the Citrix Access Gateway (CAG) client in order to access the servers. I am a programmer with rather limited ops knowledge including a weak grasp of networking and terminology. Bear with me. I was just given a new laptop, which is a 64 bit Windows 7 system unlike my previous 32 bit Windows XP desktop which was able to connect without issue. My laptop has been joined to the domain so that I login with my AD credentials, I am able to connect to the CAG and get authenticated, and after doing this I can ping our servers and they resolve to the correct internal IP addresses, but I am unable to use remote desktop to the servers, connect to SQL servers through my local SQL Management Studio, navigate to them through the file system, or view any of our internal intranet websites. All of which I was able to do previously. I have tried turning off my Windows firewall and the problem remains, the DNS servers are set to the correct IPs of our domain controllers, and the ops guys here are a little stumped. Does any one have any suggestions?

  Read the article

• Computer causing WiFi interference?

  - by Mannimarco

  I came back from college and brought my desktop computer. Family recently switched to Verizon FIOS and got a new router because of it. Unfortunately, my connection to the new wifi network is awful, with the download speeds (tested through speedtest.net) fluctuating wildly and often dropping below 1.5 Mbps. A laptop in the same room gets 20 Mbps. I've tried a new wireless card, thinking that mine got damaged in the move home but no luck. Here's where it gets weird: if I place the laptop near the computer, the laptop's download speeds often suffer greatly. Pulling the laptop away always fixes this. So now I'm under the impression that there's something in the computer (which I built a year ago and has had 0 issues up to this point) is causing an insane amount of wireless interference. Also bizarre: the upload speeds seem unaffected by this problem. On the laptop and desktop, upload speeds are generally around 5 Mpbs. Any ideas as to what could be causing this and how to test said theories would be fantastic.

  Read the article

• GnuPG Command Line - Verifying KeePass Signature

  - by Stisfa

  I'm trying to verify the PGP Signature of the latest version of KeePass 2.14's setup file against this signature, but this is the output I receive: C:\Program Files (x86)\GNU\GnuPG>gpg.exe --verify C:\Users\User\Desktop\KeePass-2.14-Setup.exe gpg: no valid OpenPGP data found. gpg: the signature could not be verified. Please remember that the signature file (.sig or .asc) should be the first file given on the command line. C:\Program Files (x86)\GNU\GnuPG> I found this command here, but it made no mention about ".sig" or ".asc" files, so I figured I did something wrong. By reading (http://www.gnupg.org/documentation/manuals/gnupg/gpgv.html#gpgv), I further tried the following: C:\Program Files (x86)\GNU\GnuPG>gpg.exe --pgpfile C:\Users\User\Desktop\KeePass-2.14-Setup.exe gpg: Invalid option "--pgpfile" C:\Program Files (x86)\GNU\GnuPG> As you can see, the results are quite obfuscating... I took a look at this on SuperUser (http://superuser.com/questions/16160/short-easy-to-understand-explanation-of-gpg-pgp-for-nontechnical-people - I couldn't use "a href" due to the built in spam filter that discriminates against users with < 10 rep; this is the same reason for the link above this link), but none of the links seemed to really address my question, at least not directly enough for me to get any idea on how to move forward on this. Can anybody here help me with the esoteric technicality of OpenPGP & the associated use of the GnuPG program? I've felt pretty dumb learning VBS, but this is beyond humiliating: it's absolutely debilitating and maiming whatever confidence I had with my IT skills (then again, I have no justification for making any boast either, as I have yet to get my A+ Cert, lol).

  Read the article

• Bash script to run a clamscan on Ubuntu- how to use return values properly?

  - by Marius

  I'm trying to put together a simple script that will scan my home directory with clamscan and give me a warning if any viruses were found. What I have so far is: #! /usr/bin/env bash clamscan -l ~/.ClamScan/$(date +"%a%b%d") -ir /home RETVAL=$? [ $RETVAL -eq 0 ] && notify-send 'clamscan finished. No viruses found' [ $RETVAL -eq 1 ] && notify-send 'clamscan found a virus' && touch ~/Desktop/VirusFound [ $RETVAL -eq 2 ] && notify-send 'clamscan encountered errors. Check the logs' && touch ~/Desktop/ClamscanError find ~/.ClamScan/* -mtime +7 -exec rm {} \; However, I'm unsure about a couple of things: I'm always wary of using rm- as far as I can tell, the find command I've got should be deleting any log files that are more than a week old. I'm also not entirely sure how the return value testing works- I've got a manual that briefly covers bash, which says that the meaning of $? is "match one character", and I'm not entirely sure how that grabs the return value. Should I be using -eq or = for testing the return value? From what I can tell -eq tests strings and = tests numerals, but I'm not sure what the type of the return value is.

  Read the article

• Rundeck get verbose output of command executing on node

  - by Leon Stafford

  I have Rundeck executing a remote script, which is in python is using print statements to return output normally such as: $ python mytest.py PASS: Condition 1 passed PASS: Condition 2 passed PASS: and so on... When I run this via Rundeck, however, it doesn't show me the same print generated outputs as above. In Rundeck's most detailed Debug output mode, I only receive the following: 06:31:12 Permanently added 'myremotenode.com' (RSA) to the list of known hosts. 06:31:12 SSH_MSG_NEWKEYS sent 06:31:12 SSH_MSG_NEWKEYS received 06:31:12 SSH_MSG_SERVICE_REQUEST sent 06:31:13 SSH_MSG_SERVICE_ACCEPT received 06:31:13 Authentications that can continue: publickey,password,keyboard-interactive 06:31:13 Next authentication method: publickey 06:31:13 Authentication succeeded (publickey). 06:31:13 /cygdrive/c/Program Files (x86)/Mozil... 06:32:06 Adding reference: ant.PropertyHelper 06:32:06 Setting project property: sshexec.output -> /cygdrive/c/Prog... I know that the remote script is actually executing just as usual, as I'm receiving other emails generated by the ~30min long script. Obviously, I don't want to have to wait 30mins to see the result of each print statement within the python script. How can I get the same level of output in Rundeck as I do in the bash shell directly?

  Read the article

< Previous Page | 384 385 386 387 388 389 390 391 392 393 394 395  | Next Page >