Search Results

Search found 12537 results on 502 pages for 'solid state'.

Page 388/502 | < Previous Page | 384 385 386 387 388 389 390 391 392 393 394 395  | Next Page >

• How do I apply multiple subnets to a server with one NIC?

  - by Cosban

  I am trying to route multiple IPs through one physical NIC on my dedicated server for use with Proxmox KVM VMs. I have a dedicated server which is currently running Debian 4.4.5-8 with 3 available ip addresses for use, which will be displayed as 176.xxx.xxx.196 (main), 176.xxx.xxx.198 (on same subnet as main) and 5.xxx.xxx.166 (different subnet). I am currently trying to route the third IP address with the dedi for use with a vps that I have set up using proxmox v2.x but am having a really, really hard time doing so. Virtual interfaces binding the additional IP addresses work as expected, ruling out external routing problems. The provider has given the following information for the IP addresses on the main subnet: gateway: 176.xxx.xxx.193 netmask: 255.255.255.224 broadcast: 176.xxx.xxx.223 As well as the following information for the IP address on the second subnet: gateway: 5.xxx.xxx.161 netmask: 255.255.255.248 broadcast: 5.xxx.xxx.167 Everything I've tried with /etc/network/interfaces has either not worked, or has rendered the network completely useless. This is the current state of the file, which has the secondary IP address working on the same subnet as well as IPv6 working, but not the second subnet. # Nativen IPv6 Schnittstelle iface eth0 inet6 manual # Bridge IPv4 Schnittstelle (176.xxx.xxx.193/27) auto vmbr0 iface vmbr0 inet static address 176.xxx.xxx.196 netmask 255.255.255.224 gateway 176.xxx.xxx.193 broadcast 176.xxx.xxx.223 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 post-up ip addr add 176.xxx.xxx.198/27 dev vmbr0 auto vmbr1 iface vmbr1 inet static address 5.xxx.xxx.166 netmask 255.255.255.248 gateway 5.xxx.xxx.161 broadcast 5.xxx.xxx.167 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 post-up ip addr add 5.xxx.xxx.166/27 dev vmbr1 # Bridge IPv6 Schnittstelle (Reichweite: xxxx:xxxx:xxxx:xxxx:xxxx:xxxx::/64) iface vmbr0 inet6 static address xxxx:xxxx:xxxx:xxxx:xxxx:xxxx netmask 64 up ip -6 route add xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 down ip -6 route del xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 up ip -6 route add default via xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 down ip -6 route del default via xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0

  Read the article

• Installing OEM Windows Server 2008 under KVM

  - by rancidfishbreath

  Issue I have an HP server that came with an OEM copy of Windows Server 2008. I have installed CentOS 5.4 on the hardware and am trying to install Windows Server 2008 as a KVM guest. When I attempt to install Windows Server 2008 it complains that I am trying to install on unsupported hardware. This issue is caused because the hardware SMBIOS information is not being passed to the KVM guest. Background Before I go any further I want to state that what I am trying to do is within the license. HP offers a supported solution for VMWare but does not have an official solution for KVM. After much research the platform I am going to use is CentOS and KVM so please do not suggest other platforms. I emailed the KVM developers mailing list and was told that this is possible and was given the advice that: "You can dump SLIC table of your host bios and provide it to guest bios using -acpitable parameter." I used dmidecode and got the parameters that need to be passed, but I do not know where to pass the parameters into. Update Looks like CentOS 5.4 uses virt-install instead of qemu. Qemu is in the package manager and I was able to install it after uninstalling qemu-img (they conflict and qemu contains the packages in qemu-img). So now I know how to pass the acpitable parameters, but I am having trouble mapping what came out of dmidecode into -acpitable.

  Read the article

• SQL Full-Text indexing not populating

  - by Sam

  Hi, We installed a clustered SQL 2005 installation on windows 2008 and reattached our san drives from another machine and restored to do a migration to new hardware. There have been a few minor issues, but this one has me stuck. Trying to populate Full-Text indexes is not working. I create a basic table with some simple text in a new database and get the same results as old indexes. 2010-09-27 10:30:46.85 spid19s Informational: Full-text Full population initialized for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'). Population sub-tasks: 1. 2010-09-27 10:31:15.36 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001DF. Attempt will be made to reindex it. 2010-09-27 10:31:15.37 spid19s The component 'MSFTE.DLL' reported error while indexing. Component path 'D:\Program Files\Microsoft SQL Server\MSSQL.1\MSSQL\Binn\MSFTE.DLL'. 2010-09-27 10:31:15.37 spid19s Error '0x80070003' occurred during full-text index population for table or indexed view '[SQL_DBA].[dbo].[CIS_Report_Executions]' (table or indexed view ID '1767677345', database ID '5'), full-text key value 0x000001E0. Attempt will be made to reindex it. The rebuild/repopulate procedure finishes, but I get zero rows in the index. The .dll in the message is present and the service accounts have access to this. My FTData also has data in it, so it seems there wouldn't be permission issue on this folder. Application throws this error: “PHP Warning: mssql_query() [function.mssql-query]: message: Full-text catalog 'ikm_PageIndex_FText' is in an unusable state. Drop and re-create this full-text catalog. (severity 16) in E:\Inetpub\knowledgebase_insidemesa\lib\database\mssql.php on line 154” A microsoft discussion is the only post I found which had claimed to fix this - said it was registry related, but then didn't post the fix.

  Read the article

• Exchange 2010 Mail Enabled Public Folder Unable to Recieve External (anon) e-mail.

  - by Alex

  Hello All, I am having issues with my "Public Folders" mail enabled folders receiving e-mails from external senders. The folder is setup with three Accepted Domains (names changed for privacy reasons): 1 - domain1.com (primary & Authoritative) 2 - domain2.com (Authoritative) 3 - domain3.com (Authoritative) When someone attempts to send an e-mail to [email protected] from inside the organization, the e-mail is received and placed in the appropriate folder. However, when someone tries to send an e-mail from outside the organization (such as a gmail account), the following error message is received: "Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 Recipient address rejected: User unknown (state 14)." When I try to send an e-mail to the same folder, using the same e-mail address above ([email protected]), but with domain2.com instead of domain3.com, it works as intended (both internal & external). I have checked, double checked, and triple checked my DNS settings comparing those from domain2 & domain3 with them both appearing identical. I have tried recreating the folders in question with the same results. I have also ran Get-PublicFolderClientPermission "\Web Programs\folder" with the following results for user anonymous: RunspaceId : 5ff99653-a8c3-4619-8eeb-abc723dc908b Identity : \Web Programs\folder User : Anonymous AccessRights : {CreateItems} Domain2.com & Domain3.com are duplicates of each other, but only domain2.com works as intended. All other exchange functions are functioning properly. If anyone out there has any suggestions, I would love to hear them. I've just hit a brick wall. Thanks for all your help in advance! --Alex

  Read the article

• Multiple IPs on firewall, are these virtual interfaces or what?

  - by Jakobud

  We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

  Read the article

• Huge or minimal performance hit running game servers on a Virtual Machine? [closed]

  - by Damainman

  I have a two dedicated servers to choose from depending on which one would do a better job. I plan on updating the Hard Drive space and RAM at a later date depending on how I move forward. Server 1: 500GB Hard Drive 8GB RAM 2x 64bit Intel Xeon L5420(Quad Core) @ 2.50Ghz Server2: 500GB Hard Drive 8GB RAM 2x 64bit Intel Xeon E5420(Quad Core) @ 2.50GHz I want to run a virtual machine that will host about 10 game servers, with about 16 active slots per server. It will be a mix and match from: Minecraft Counter Strike( 1.6, Source, Global Offensive) Battlefield Team Fortress I know the general consensus is virtualization is a horrible idea if you plan on running virtual servers on them. The issue is, the discussions I read do not really clearly state whether they are speaking about a virtual server running inside an OS(ie: VMware Player running on Windows with the game server in a VM) or a Hypervisor such as Xen Cloud Platform. I am trying to get a definite answer on how feasible the above would be and how much of a performance hit it might be if the VM running the game servers is on a hypervisor such as Xen Cloud Platform. My initial research lead me to believe that there wouldn't be a performance hit since the virtualization is different than running it via inside of a OS.

  Read the article

• Delay NTP Initialisation, Cisco 877W, IOS 12.4(24)T1

  - by Mike Insch

  I have a Cisco 877W which I'm using for my home ADSL connection (and as a refresher in Cisco IOS). I've got a working config in-place with my PPPoA connection coming online correctly, and VLANs and other settings configured as I want them, but I can't crack the NTP configuration. For NTP, I have the following defined ntp server 0.uk.pool.ntp.org source Dialer0 ntp server 1.uk.pool.ntp.org source Dialer0 ntp server 2.uk.pool.ntp.org source Dialer0 ntp server 3.uk.pool.ntp.org source Dialer0 This setup works fine when issued in Global Configuration Mode when the Dialer0 interface (ATM0.1) is up. The configuration fails at startup though: Translating "1.uk.pool.ntp.org"...domain server (208.67.222.222) (208.67.220.220) ntp server 1.uk.pool.ntp.org source Dialer0 ^ % Invalid input detected at "^" marker. This is repeated for the other servers defined. Obviously the DNS lookup for the server(s) fails because the DNS servers cannot be accessed because the external interface is not yet online. Is there a way to delay the NTP configuration until afte the Dialer0 interface is fully initialised? Can the NTP commands be triggered by the Line Protocol on the Dialer0 interface transitioning to the up state? Alternatively, can the NTP commands be delayed for 5 minutes after the router has finished initialising? Any advice, or pointers to useful documentation or examples gratefully received ...

  Read the article

• Which linux distributions offer seamless support for UEFI and an LVM root out of the box?

  - by Jannik Jochem

  My new ultrabook (an Asus UX32VD) requires UEFI in order to boot from the internal harddisk. I use an LVM partition which contains my root fs and dual-boot Windows 8. I somehow managed to get this working on Sabayon Linux, however the overall process was pretty painful, and system upgrades keep breaking my configuration because everything depends on a hand-configured kernel and a hand-crafted GRUB2 configuration. This causes a lot of hassle and distractions for me, so I am considering to switch to a different distribution. However, I cannot find any concrete resources that precisely document the state of UEFI support in the popular distributions. As an example, the length of the Ubuntu wiki page on UEFI suggests that installing on UEFI systems is a non-trivial process, and this AskUbuntu thread on encrypted LVM on UEFI systems suggests that LVM might also be a problem. I know that this question seems somewhat open-ended, so I'll formulate concrete questions: Are there any Linux distributions with an installer that supports installing to an LVM root in a UEFI boot setting where Windows 8 is dual-booted? Which distributions support UEFI without having to jump through hoops in order to bootstrap into a UEFI-booted system or requiring manual configuration of the boot manager?

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• How to use Python to read the physical address(MAC ID) [closed]

  - by getjoefree

  I want to read the physical address of the NIC model, i can get the results that i want to with SED.EXE before, but SED.EXE does not support my environment but Python ok, who have the means to do it. The general situation (not plug the network cable, it is impossible to obtain IP address): Ethernet adapter: Connection-specific DNS Suffix.: Chianet Description ...........: Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller Physical Address .........: A4-BA-DB-9D-1E-8E Dhcp Enabled ...........: Yes Autoconfiguration Enabled ....: Yes Ethernet adapter 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1510 Wireless-N WLAN Mini-Card Physical Address. . . . . . . . . : 00-23-4D-D9-C0-28 The description of the NIC different, we can use this to fetch the corresponding physical address, base on Physical Address does not work, because the computer with the WLAN Card, I want to use Python to read my computer the card information and after Python handles an output file, output file format: SET MAC = A4BADB9D1E8E and sed format: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" > WINMAC.BAT getmac.sed: /Marvell Yukon 88E8040/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; }

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• Cooling for a small server room

  - by John Zwinck

  I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

  Read the article

• update from debian lenny to squeeze

  - by Daniel

  I'm trying to update from debian lenny to squeeze on my 64bit root server and did the following so far: modifying sources.list apt-get update apt-get upgrade apt-get install linux-image-2.6-amd64 The last step leads to the following error-output: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: linux-image-2.6-amd64: Depends: linux-image-2.6.32-5-amd64 but it is not going to be installed E: Broken packages UPDATE: here's my sources.list deb ftp://mirror.hetzner.de/debian/packages squeeze main contrib non-free deb ftp://mirror.hetzner.de/debian/security squeeze/updates main contrib non-free deb http://ftp.de.debian.org/debian squeeze main non-free contrib deb-src http://ftp.de.debian.org/debian squeeze main non-free contrib deb http://security.debian.org/ squeeze/updates main contrib non-free deb-src http://security.debian.org/ squeeze/updates main contrib non-free How can I fix that safely? thx

  Read the article

• Why do I have 55 local area connections in ipconfig?

  - by RMorrisey

  Windows Vista Home Premium. I should mention that I am having no problem whatever getting an internet connection. When I type "ipconfig" in the console, I get (55!) messages of 3 lines each, listing a ton of disconnected network connections. My PC only has one network card. Each message looks like this: Tunnel adapter Local Area Connection* 55: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : These don't cause a major problem; they make it a pain, though, to fish upward and find my IP address. How can I get rid of them? Edit: Actually, a few connection numbers are randomly missing from the sequence; so, it's really more like 30 or 40 connection messages, rather than all 55. Not sure why that is, either.

  Read the article

• Email bouncing sent from Google

  - by davidmck

  I'm hoping someone here has an idea of where to look next. We have a domain we support which has email sent to it from one particular user bounce with the following message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 Unrouteable address (state 14). We only have reports of bouncing form this one particular user (who is someone we don't support - except they'd like to be able to contact our customer and we're trying to figure out if the problem is on our end). Many people can successfully send to this domain and the user who is getting bounce messages can send to other domains that we support (so it's clearly something specific with the princetonscoop.com domain and not our setup in general). I've reviewed the MX records multiple times and the server logs don't show a connection which generates this error (in fact this error is not one that our mail server would ever return). So it appears that google is contacting a different mail server for some reason. I have tested sending from my gmail account and that works. I believe the sender is using a google-apps account (the account they are using is from their own domain, not a gmail account). Any ideas on what might be happening here or what to test/investigate next? Thanks.

  Read the article

• iis7 large worker process request queue creating process blocking aspnet.config & machine.config amended (bottleneck)

  - by scott_lotus

  ASP.net 2.0 app .net 2.0 framework IIS7 I am seeing a large queue of "requests" appear under the "worker process" option. State recorded appear to be Authenticate Request and Execute Request Handles more than anything else. I have amended aspnet.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727 (32 bit path and 64 bit path) to include: maxConcurrentRequestsPerCPU="50000" maxConcurrentThreadsPerCPU="0" requestQueueLimit="50000" I have amended machine.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727\CONFIG (32 bit and 64 bit path) to include: autoConfig="true" maxIoThreads="100" maxWorkerThreads="100" minIoThreads="50" minWorkerThreads="50" minFreeThreads="176" minLocalRequestFreeThreads="152" Still i get the issue. The issue manifestes itself as a large number of processes in the Worker Process queue. Number of current connections to the website display 500 when this issue occurs. I dont think i have seen concurrent connections over 500 without this issue occurring. Web application slows as the request block. Refreshing the app pool resolves for a while (as expected) as the load is spread between the two pools. Application pool in question FIXED REQUEST have been set to refresh on 50000. Thank you for any help. Scott quick edit to say hmm, my develeopers are telling me the project was built with .net 3.5 framework. Looking at C:\Windows\Microsoft.NET\Framework64\v3.5 there does not appear to be a ASPNET.CONFIG or a MACHINE.CONFIG .... is there a 3.5 equivalent ? after a little searching apparenetly 3.5 uses the 2.0 framework files that 3.5 is missing. So back to the original question , where is my bottleneck ?

  Read the article

• Backup with Mercurial and Robocopy?

  - by Andrew Neely

  The Problem We would like to backup our critical files from several network shares to a removable hard drive. We want to automate the backup so we don't have to remember to run it. It needs to finish overnight. Furthermore, we want to be able to preserve multiple versions of each file so we can back out of our user's mistakes easier. Background Information I work in a large Windows-based enterprise with a centralized IT section who is responsible for all backups. Their backups are geared towards disaster recovery and not user error, and require upper-level management approval for any non-disaster recoveries. Several times we have noticed that our backups have failed, we weren't notified. I do not have administrative rights to the server or my desktop. We are trying to backup some 198,000 files spanning about 240 gigabytes. These files rarely change. Our backup drive is one terabyte. My Proposed Solution What I would like to do is to write a batch file using Robocopy with the /mir option along with Mercurial SCM to store all versions of the file. I would do an hg add followed by an hg commit before each execution of Robocopy to save the current state, and then make a mirrored copy of the file structures. The problem is the /mir will delete every folder not present in the source, and Mercurial stores the repository in a .hg folder in the destination folder. Does anybody know how I could either convince Mercurial to store the .hg folder elsewhere, or convince Robocopy not to delete it from the destination? I'm trying to avoid writing a custom program do to copying.

  Read the article

• DansGuardian/Squid Traffic doesn't get back to user

  - by DKNUCKLES

  I've purchased a Squid appliance that I'm attempting to implement, however the lack of documentation has left me a bit high and dry. Forgive me if this is a silly question, but this is my first attempt at implementing Squid. From what I can ascertain from the documentation (or lack thereof), the users connect to DansGuardian first at port 8080 where the filtering is done, at which point it forwards it to the Squid appliance at port 3128. The traffic is then sent to the internet. The setup I have is as follows Gateway (MikroTik router) : 192.168.88.1 Squid/DansGuardian :192.168.88.100 Client : 192.168.88.238 Client --- Gateway --- Proxy --- Internet I have set up a simple NAT rule to forward all traffic from the client machine (for testing purposes) to go to the DansGuardian. The traffic seems to get there, although I see a lot of SYN_RECV w/ a netstat -antp command on the virtual appliance machine. From this I gather that the traffic is NOT being routed back to the client machine. Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN - tcp 0 0 192.168.88.100:8080 192.168.88.238:55786 SYN_RECV - tcp 0 0 192.168.88.100:8080 192.168.88.238:55787 SYN_RECV - tcp 0 0 192.168.88.100:8080 192.168.88.238:55785 SYN_RECV - tcp 0 0 192.168.88.100:8080 192.168.88.238:55788 SYN_RECV - tcp 0 0 0.0.0.0:10000 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - Is this a routing issue or an issue with the Squid Appliance?

  Read the article

• Kubuntu: apt-get install of php5-dev: libtool version mismatch?

  - by pinkgothic

  (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

  Read the article

• Kubuntu: apt-get install of php5-dev: libtool version mismatch?

  - by pinkgothic

  (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

  Read the article

• Unable to install mysql-server in Ubuntu

  - by Arihant

  I am unable to install mysql-server on my ubuntu 9.10 server machine. When using apt-get install mysql-server the output is : # apt-get install mysql-server Reading package lists... Done Building dependency tree Reading state information... Done mysql-server is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 120 not upgraded. 2 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up mysql-server-5.1 (5.1.37-1ubuntu5.4) ... * Stopping MySQL database server Mysqld [ OK ] * Starting MySQL database server mysqld [fail] invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.1 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.1; however: Package mysql-server-5.1 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: mysql-server-5.1 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) I cant find a satisfactory solution to this problem anywhere. Many sites tell to reinstall it but its not working. Any help will be appreciated. Thank you..

  Read the article

• MySQL taking a long time to start

  - by Dscoduc

  I'm running Windows Server 2008 with MySQL installed and every time I reboot the server the MySQL Service doesn't start right away. A look into the Windows Eventlog shows that the MySQL Service was hung at startup. Looking at the Services.msc console shows the service state at Starting... Eventually, like 10 minutes, the MySQL Service actually finishes the startup process and the database becomes available for my Wordpress server... I looked at the MySQL .err files and didn't find anything that would indicate a delay in the statup process... Can anyone suggest a way to determine what is causing the delay, and more importantly, how to prevent the delay in the MySQL Startup? UPDATE: Here is the .err log contents from the shutdown to the startup complete. Notice the startup begins at 10:30:00 and the MySQL isn't ready for connections until 10:47:14, a full 17 minutes later: 100322 10:27:06 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Normal shutdown 100322 10:27:06 [Note] Event Scheduler: Purging the queue. 0 events 100322 10:27:06 InnoDB: Starting shutdown... 100322 10:27:08 InnoDB: Shutdown completed; log sequence number 4 3854351346 100322 10:27:08 [Warning] Forcing shutdown of 1 plugins 100322 10:27:08 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Shutdown complete 100322 10:30:00 [Note] Plugin 'FEDERATED' is disabled. 100322 10:30:01 InnoDB: Started; log sequence number 4 3854351346 100322 10:47:14 [Note] Event Scheduler: Loaded 0 events 100322 10:47:14 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: ready for connections. UPDATE 2: MySQL is configured as a service (part of the install process, nothing I did) and executes the following syntax (as it appears in the registry): "C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld" --defaults-file="C:\Program Files\MySQL\MySQL Server 5.1\my.ini" MySQL

  Read the article

• Lotus Domino - DAOS not reducing file size?

  - by SydxPages

  I have implemented DAOS on a Lotus Domino Server (8.5.3 FP2) as follows: Lotus Domino Server Document: Store file attachments in DAOS: Enabled Minimum size of object before Domino will store in DAOS: 64000 bytes DAOS base path: E:\DAOS Defer object deletion for: 30 days Transaction logging is running, and the specific test database has the following advanced properties set: Domino Attachment and Object Service (ticked) Use LZ1 compression for atachments Compress Database Design Compress Data I have restarted the server. When I run a compact -c, it compacts the database, but does not reduce the size. I have checked the DB in Windows Explorer (60Gb) and the size is the same pre and post. I have checked the directory (E:\DAOS) and it is 35Gb in size. When I run the command 'Tell DAOSMgr Status tmp\test.nsf', I get the following response. From looking up on the net, I believe ticket count = 0 means that the db is not really DAOS'ed? Admin Process: Searching Administration Requests database DAOSMGR: Status tmptest.nsf started DAOS database status: Database: E:\Lotus\Domino\Data\tmp\test.nsf Database state = Synchronized Last resynchronized: 03/09/2012 02:49:13 PM Ticket count: 0 DAOSMGR: Status tmp\test.nsf completed I have run fixup on the database. When I have tried to run the DAOS estimator it has always crashed. This was a problem with larger databases on earlier versions of domino, but not anymore. Can anyone tell me why the size has not reduced? Am I missing anything?

  Read the article

• Connection timeout when trying to SSH

  - by dan

  The other day I tried to connect to my remote server via SSH as i always have. But now when I try to connect it just times out after about 60 seconds. I run service ssh start Which tells me that Job is already running: ssh. I then ran $netstat -tnlp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:993 0.0.0.0:* LISTEN 1972/dovecot tcp 0 0 0.0.0.0:995 0.0.0.0:* LISTEN 1972/dovecot tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 2030/mysqld tcp 0 0 0.0.0.0:110 0.0.0.0:* LISTEN 1972/dovecot tcp 0 0 0.0.0.0:143 0.0.0.0:* LISTEN 1972/dovecot tcp 0 0 0.0.0.0:10000 0.0.0.0:* LISTEN 2157/perl tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 3028/sshd tcp 0 0 0.0.0.0:25 0.0.0.0:* LISTEN 2273/master tcp6 0 0 :::80 :::* LISTEN 2618/apache2 tcp6 0 0 :::21 :::* LISTEN 2291/proftpd: (acce tcp6 0 0 :::22 :::* LISTEN 3028/sshd I am able to access subdomains on my site, and FTP, but don't have the ability to SSH or even ping remotely. Any thoughts?

  Read the article

< Previous Page | 384 385 386 387 388 389 390 391 392 393 394 395  | Next Page >