Search Results

Search found 26263 results on 1051 pages for 'linux guest'.

Page 389/1051 | < Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >

  • Can a 32-bit RHEL4 userland work with a 64-bit kernel?

    - by James
    Is there a way to change an i386 RHEL4 machine to run an amd64 kernel, but ensure that it still builds software into same i386 binaries? On Debian this seems quite straightforward: just install an amd64 kernel (worst case, build one like this guy: http://www.debian-administration.org/users/jonesy/weblog/1) and prefix everything with "linux32". Then everything that considers uname -m will be unchanged, I just need to handle the few cases that consider uname -r. What is the Red Hat equivalent? Is the only way a full 64-bit installation on another disk and then chrooting back to the 32-bit system before anyone builds anything? (Even the best examples of that seem to be Debian-based.) Background: We make a large system that runs on (a variant of) i386 RHEL4. However, some of the larger RHEL build machines now have enough RAM that they might benefit from going 64-bit (for the kernel and maybe some of the bigger build steps). Our build system doesn't support cross-compilation.

    Read the article

  • ACL and moving files in Nautilus

    - by MyOnlyEye
    When I move files from a private home directory (e.g. /home/jack) to a shared directory (e.g. /home/shared-school) Nautilus copies the file permissions from the original file into the shared directory - and ignores the ACL that I've put in the /home/shared-school directory (e.g. setfacl -R -m d:g:school:rwx /home/shared-school). Is it possible to force Nautilus to change ACL on a file that is moved or copied - or not to ignore the ACL on the directory where the files are moved or copied?

    Read the article

  • Simple mdadm RAID 1 not activating spare

    - by Nick Liu
    I had created two 2TB HDD partitions (/dev/sdb1 and /dev/sdc1) in a RAID 1 array called /dev/md0 using mdadm on Ubuntu 12.04 LTS Precise Pangolin. The command sudo mdadm --detail /dev/md0 used to indicate both drives as active sync. Then, for testing, I failed /dev/sdb1, removed it, then added it again with the command sudo mdadm /dev/md0 --add /dev/sdb1 watch cat /proc/mdstat showed a progress bar of the array rebuilding, but I wouldn't spend hours watching it, so I assumed that the software knew what it was doing. After the progress bar was no longer showing, cat /proc/mdstat displays: md0 : active raid1 sdb1[2](S) sdc1[1] 1953511288 blocks super 1.2 [2/1] [U_] And sudo mdadm --detail /dev/md0 shows: /dev/md0: Version : 1.2 Creation Time : Sun May 27 11:26:05 2012 Raid Level : raid1 Array Size : 1953511288 (1863.01 GiB 2000.40 GB) Used Dev Size : 1953511288 (1863.01 GiB 2000.40 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Mon May 28 11:16:49 2012 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : Deltique:0 (local to host Deltique) UUID : 49733c26:dd5f67b5:13741fb7:c568bd04 Events : 32365 Number Major Minor RaidDevice State 1 8 33 0 active sync /dev/sdc1 1 0 0 1 removed 2 8 17 - spare /dev/sdb1 I've been told that mdadm automatically replaces removed drives with spares, but /dev/sdb1 isn't being moved into the expected position, RaidDevice 1. UPDATE (30 May 2012): A badblocks destructive read-write test of the entire /dev/sdb yielded no errors as expected; both HDDs are new. As of the latest edit, I assembled the array with this command: sudo mdadm --assemble --force --no-degraded /dev/md0 /dev/sdb1 /dev/sdc1 The output was: mdadm: /dev/md0 has been started with 1 drive (out of 2) and 1 rebuilding. Rebuilding looks like it's progressing normally: md0 : active raid1 sdc1[1] sdb1[2] 1953511288 blocks super 1.2 [2/1] [U_] [>....................] recovery = 0.6% (13261504/1953511288) finish=2299.7min speed=14060K/sec unused devices: <none> I'm now waiting on this rebuild, but I'm expecting /dev/sdb1 to become a spare just like the five or six times that I've tried rebuilding before. UPDATE (31 May 2012): Yeah, it's still a spare. Ugh! UPDATE (01 June 2012): I'm trying Adrian Kelly's suggested command: sudo mdadm --assemble --update=resync /dev/md0 /dev/sdb1 /dev/sdc1 Waiting on the rebuild now... My questions are: Why isn't the spare drive becoming active sync? How can I make the spare drive become active?

    Read the article

  • Trying to change a ubuntu user's password, Authentication token manipulation err

    - by beagleguy
    hey all, I'm trying to create a local user on a new ubuntu box my admin set up. I'm unable to change the password, I keep getting the error below. The user gets added to the shadow file but I can't get it to set a password. Any ideas? I've googled for over an hour :( thanks! admin@theserver:~$ sudo useradd jamz [sudo] password for admin: admin@theserver:~$ sudo passwd jamz passwd: Authentication token manipulation error passwd: password unchanged admin@theserver:~$

    Read the article

  • external disk suddenly unmounting

    - by hasen j
    Platform: Ubuntu 9.10 Disk Brand/model: WD My Book The external hard disk suddenly unmounts after a while. I suspect it's due to it "sleeping" to save power. I don't recall the problem having occurred before the upgrade to Karmic. How can this be fixed?

    Read the article

  • How do I reference the value of a constructed environment variable in a loop?

    - by Rob Spieldenner
    What I'm trying to do is loop over environment variables. I have a number of installs that change and each install has 3 IPs to push files to and run scripts on, and I want to automate this as much as possible (so that I only have to modify a file that I'll source with the environment variables). The following is a simplified version that once I figure out I can solve my problem. So given in my.props: COUNT=2 A_0=foo B_0=bar A_1=fizz B_1=buzz I want to fill in the for loop in the following script #!/bin/bash . <path>/my.props for ((i=0; i < COUNT; i++)) do <script here> done So that I can get the values from the environment variables. Like the following(but that actually work): echo $A_$i $B_$i or A=A_$i B=B_$i echo $A $B returns foo bar then fizz buzz

    Read the article

  • Basic clarification about Limited FTP/sFTP users

    - by mattewre
    I would like to get some clarification about the correct way to create limited users to access to my VPS user as WEBSERVER with Nginix. I'm used to NOT install FTP and access via SFTP only. It is ok for every set up? this is what I usually do from to create a limited user called "admin" that should be able to have access via SFTP to the folder with the website data mkdir -p /var/www/mysite.com/ adduser admin adduser admin www-data chown -R root:root /var/www chmod -R 755 /var/www chmod -R 755 /var/www/mysite.com chown -R admin:www-data /var/www/mysite.com/ It seems not to be the correct way, I always have problems with permission when I upload some files (for example with Wordpress in general). I would like to create an user that does work exactly as the one that the "provides" give to their client when they buy an Hosting service (that is a FTP, I would prefer SFTP access). It is for personal user, but I think that a limited user is a lot safer to use then the "root" via SFTP.

    Read the article

  • Make `mount` choose a device

    - by o_O Tync
    I have a mount point — let it be /media/question — and two possible devices: a physical HDD and a remote NFS folder. Sometimes I plug the device in physically, in other cases I mount it via NFS. Is there a way to specify both of them in fstab so that executing mount /media/question will preferably choose physical volume, and when it's not available — NFS?

    Read the article

  • How to download all file content from a folder using wget and http

    - by user1526912
    I am trying to use wget and http to download all contents from folderAA below to directory /root/sstest wget -r --directory-prefix="/root/sstest" -o /root/sstest2.log http://site.com/folder1/folder2/folderAA/ When I submit the above command nothing is downloaded. If I submit a wget request for a specific file from folderAA the file is actually downloaded to /root/sstest: wget -r --directory-prefix="/root/sstest" -o /root/sstest2.log http://site.com/folder1/folder2/folderAA/file.txt Can someone tell me why I cannot download all file content from folderAA at once using the first wget request?

    Read the article

  • Hybrid gmail MX + postfix for local accounts

    - by krunk
    Here's the setup: We have a domain, mydomain.com. Everything is on our own server, except general email accounts which are through gmail. Currently gmail is set as the MX record. The server also has various email aliases it needs to support for bug trackers and such. e.g. [email protected] |/path/to/issuetracker.script I'm struggling with a setup that allows the following, both locally and from user's email clients. guser1 - has a gmail account and a local account guser2 - only has a gmail account bugs - has a pipe alias in /etc/aliases for issue tracker Scenarios mail to [email protected] from local host (crons and such) needs to go to gmail account mail to [email protected] from local host mail to [email protected] needs to be piped to the local issue tracker script So, the first stab was creating a transport map. In this scenario, the our server would be set as teh MX and guser* destined emails are sent to gmail. Put the gmail users in a map like so: [email protected] smtp:gmailsmtp:25 [email protected] smtp:gmailsmtp:25 Problems: Ignores extensions such as [email protected] Only works if append_at_myorigin = no (if set to yes, gmail refuses to connect with: E4C7E3E09BA3: to=, relay=none, delay=0.05, delays=0.02/0.01/0.02/0, dsn=4.4.1, status=deferred (connect to gmail-smtp-in.l.google.com[209.85.222.57]:25: Connection refused)) since append_at_myorigin is set to no, all received emails have (unknown sender) The second stab was to set explicit localhost aliases in /etc/aliases and do a domain wide forward on mydomain. This too requires setting the local server as the MX: root: root@localhost # transport mydomain.com smtp:gmailsmtp:25 Problems: * If I create a transport map for a domain that matches "$myhostname", the aliases file is never parsed. So when a local user (or daemon) sends an email like: mail -s "testing" root < text.txt Postfix ignores the /etc/alias entry and maps to [email protected] and attempts to send it to the gmail transport mapping. Third stab: Create a subdomain for the bugs, something like bugs.mydomain.com. Set the MX for this domain to local server and leave the MX for mydomain.com to the Gmail server. Problems: * Does not solve the issue with local accounts. So when the bug tracker responds to an email from [email protected], it uses a local transport and the user never receives the email. % postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_at_myorigin = no append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = $myhostname, localhost.$myhostname, localhost myhostname = mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_cert_file = /etc/ssl/certs/kspace.pem smtp_tls_enforce_peername = no smtp_tls_key_file = /etc/ssl/certs/kspace.pem smtp_tls_note_starttls_offer = yes smtp_tls_scert_verifydepth = 5 smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_destination smtpd_tls_ask_ccert = yes smtpd_tls_req_ccert = no smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport

    Read the article

  • Triple monitor setting in Linux with USB-HDMI adapter

    - by Oscar Carballal
    I'm trying to set up a triple monitor desktop at my office using Fedora 17, but it seems impossible, let me explain the setting: Laptop ASUS K53SD with 2 graphic cards, Intel and nVidia (Screen controled by Intel card) 24" Full HD monitor connected to the HDMI output (controlled by Intel card) 23" Full HD monitor connected to an USB-HDMI adapter (via framebuffer in /dev/fb2, apparently) VGA output (not used) controlled by nVidia card First of all, the USB-HDMI adapter works perfectly, it gives me a green screen (which means the communication is OK) and I can make it work if I set up a single monitor setting via framebuffer in Xorg. Here I leave the page where I got the instructions: http://plugable.com/2011/12/23/usb-graphics-and-linux Now I'm trying to set up the the two main monitors (laptop and 24") with the intel driver and the 23" with the framebuffer, but the most succesful configuration I get is the two main monitors working and the third disconnected. Do you have any idea what can I do to make this work? Here I leave my xRandr output and my Xorg conf: -> xrandr Screen 0: minimum 320 x 200, current 3286 x 1080, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA2 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 531mm x 299mm 1920x1080 60.0*+ 50.0 25.0 30.0 1680x1050 59.9 1680x945 60.0 1400x1050 74.9 59.9 1600x900 60.0 1280x1024 75.0 60.0 1440x900 75.0 59.9 1280x960 60.0 1366x768 60.0 1360x768 60.0 1280x800 74.9 59.9 1152x864 75.0 1280x768 74.9 60.0 1280x720 50.0 60.0 1440x576 25.0 1024x768 75.1 70.1 60.0 1440x480 30.0 1024x576 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 720x576 50.0 848x480 60.0 720x480 59.9 640x480 72.8 75.0 66.7 60.0 59.9 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) 1920x1080_60.00 60.0 The Xorg file: # Xorg configuration file for using a tri-head display Section "ServerLayout" Identifier "Layout0" Screen 0 "HDMI" 0 0 Screen 1 "USB" RightOf "HDMI" Option "Xinerama" "on" EndSection ########### MONITORS ################ Section "Monitor" Identifier "USB1" VendorName "Unknown" ModelName "Acer 24as" Option "DPMS" EndSection Section "Monitor" Identifier "HDMI1" VendorName "Unknown" ModelName "Acer 23SH" Option "DPMS" EndSection ########### DEVICES ################## Section "Device" Identifier "Device 0" Driver "intel" BoardName "GeForce" BusID "PCI:0:02:0" Screen 0 EndSection Section "Device" Identifier "USB Device 0" driver "fbdev" Option "fbdev" "/dev/fb2" Option "ShadowFB" "off" EndSection ############## SCREENS ###################### Section "Screen" Identifier "HDMI" Device "Device 0" Monitor "HDMI1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "USB" Device "USB Device 0" Monitor "USB1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • Command to find the source package of a binary?

    - by Delan Azabani
    I know there's a which command, that echoes the full name of a binary (e.g. which sh). However, I'm fairly sure there's a command that echoes the package that provides a particular binary. Is there such a command? If so, what is it? I'd like to be able to run this: commandName ls and get coreutils for example.

    Read the article

  • Not able to delete file from server with permissions of 644 via PHP script

    - by letseatfood
    I am trying to delete JPEG files that were uploaded to the server via FTP. The files are uploaded and written with permissions of 644. The owner and group of the upload directory are mike and mike. I have tried changing the owner and group to www-data, but that does not seem to work. I am trying to delete the files with a PHP script using unlink(). This works on the production server (which is a hosting service), but not my development server, which is a LAMP setup. This leads me to believe it has something to do with permissions on my development server.

    Read the article

  • mod_ntlm for RHEL 5.3

    - by vikasa
    I tried to compile mod_ntlm for Oracle HTTP Server but got all sorts of errors, can someone point me to a pre-compiled binary? Tried everything at http://wiki.bestpractical.com/view/NtlmAuthentication still no go Thanks

    Read the article

  • External monitor image not centered in the screen

    - by kemp
    I'm using Xorg 7.5 on a Radeon HD4870 with the FOSS radeonhd server on my HP 6830s. The laptop has a VGA connector and I attach it to a 37" panasonic plasma TV. It works fine except for a little annoyance: when activated, the TV screen is set to the resolution of 1360x768 (which it reports as being the highest it supports) but all the image is shifted by about 100 pixels to the right. I can't see the leftmost part of the page, and I have a black vertical bar to the right. If I change the resolution to 1024x768 there is no shifting, the image fills the entire screen with no parts hidden, but at this resolution the image is stretched. How can I tune the position on the external monitor so that the image is centered in the screen filling it entirely?

    Read the article

  • Insufficient channel capacity of 1GBit

    - by Roman S
    There is a Caching Server (Varnish): it receives data from Amazon S3 on request, saves it for some time and gives it to the client. We have encountered the problem of insufficient channel capacity of 1GBit. Peak load within 4 hours completely chokes the channel. Server performance is sufficient for now. Approximately 4.5TB of data are transmitted per day. More than 100TB are accumulated per month. The first thought that comes to mind is simply to add one more 1GBit port and sleep peacefully until 2GBit are not enough (it may happen quite quickly) or one server is not able to handle it. And then we just need to add new Caching Servers. But now we need a Load Balancer, which will send requests on one and the same URL, always on one and the same server (to avoid multiple copies of the same cached objects). Here are the questions: Does a Balancer need a band equal to sum of all bands of Caching Servers? What shall we do in case there are no ports in a Balancer? Should we add more Balancers or solve the problem by means of Round robin DNS? What are the standard approaches to such problems? Can anyone advise hosting-companies, which can solve this problem? We are interested in American and European markets.

    Read the article

  • MySQL Master - Master Broken

    - by Recc
    I've Inherited a Mysql master master system, I've noticed the second master (lets call it slave from now on as it's running on a 'slave' machine) stopped getting its db's updated. I saw that Master: Slave_IO_Running: Yes Slave_SQL_Running: Yes Slave: (with an error I truncated) Slave_IO_Running: Yes Slave_SQL_Running: No Last_Errno: 1062 Last_Error: Error 'Duplicate entry '3' for key 'PRIMARY'' on [...] I don't know what caused it to process considering we cant get duplicate there. What's important is to resume normal operations; Right now I've stop slave; on the Master and stop slave; on the Slave because I saw that if I change records on the Slave the changes Do Get Propagated to Master which is in active use. How do I: Force sync EVERYTHING from master to slave without affecting data on master? Then hopefully have slave pickup replication as usual? UPDATE OK I Tried deleting all tables on slave then it complained in that error section that the 'table' doesnt exist. So i made a no data dump of Master, and made sure I have only empty tables in Secondary (slave). I start slave; on slave BUT now it's complaining about bloody alter table statements for instance: Last_Errno: 1060 Last_Error: Error 'Duplicate column name [...] Query: 'ALTER TABLE [...] How to skip the fracking alter statements I just want to replicate the bloody data and be done with it, my tables have the lates changes already FFS and now its complaining about changes made after the replication seized weeks ago How do I reset the log or something? OUTSTANDING Why would this start happening? The "Secondary" is propagating to "Primary". "Primary" is not propagating to "Secondary". But any fixes I tried to do left it in the same state Yes-Yes Yes-No with same Last_Error. I think around that time the server was taken off the network, could that confuse MySQL in some way?

    Read the article

  • What kernel modules are required for wi-fi to work?

    - by Leonid Shevtsov
    My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

    Read the article

  • Can enabling a RAID controller's writeback cache harm overall performance?

    - by Nathan O'Sullivan
    I have an 8 drive RAID 10 setup connected to an Adaptec 5805Z, running Centos 5.5 and deadline scheduler. A basic dd read test shows 400mb/sec, and a basic dd write test shows about the same. When I run the two simultaneously, I see the read speed drop to ~5mb/sec while the write speed stays at more or less the same 400mb/sec. The output of iostat -x as you would expect, shows that very few read transactions are being executed while the disk is bombarded with writes. If i turn the controller's writeback cache off, I dont see a 50:50 split but I do see a marked improvement, somewhere around 100mb/s reads and 300mb/s writes. I've also found if I lower the nr_requests setting on the drive's queue (somewhere around 8 seems optimal) I can end up with 150mb/sec reads and 150mb/sec writes; ie. a reduction in total throughput but certainly more suitable for my workload. Is this a real phenomenon? Or is my synthetic test too simplistic? The reason this could happen seems clear enough, when the scheduler switches from reads to writes, it can run heaps of write requests because they all just land in the controllers cache but must be carried out at some point. I would guess the actual disk writes are occuring when the scheduler starts trying to perform reads again, resulting in very few read requests being executed. This seems a reasonable explanation, but it also seems like a massive drawback to using writeback cache on an system with non-trivial write loads. I've been searching for discussions around this all afternoon and found nothing. What am I missing?

    Read the article

  • Need advice on which PCI SATA Controller Card to Purchase

    - by Matt1776
    I have a major issue with the build of a machine I am trying to get up and running. My goal is to create a file server that will service the needs of my software development, personal media storage and streaming/media server needs, as well as provide a strong platform for backing up all this data in a routine, cron-job oriented German efficiency sort of way. The issue is a simple one - all my drives are SATA drives and my motherboard controller only contains 4 ports. Solving the issue has proven to be an unmitigated nightmare. I would like advice on the purchase of the following: 4 Port internal SATA / 2 Port external eSATA PCI SATA Controller Card that has the following features and/or advantages: It must function. If I plug it in and attach drives, I expect my system to still make it to the Operating System login screen. It must function on CentOS, and I mean it must function WELL and with MINIMAL hassle. If hassle is unavoidable, there shall be CLEAR CUT and EASY TO FOLLOW instructions on how to install drivers and other supporting software. I do not need nor want fakeRAID - I will be setting up any RAID configurations from within the operating system. Now, if I am able to find such a mythical device, I would be eternally grateful to whomever would be able to point me in the right direction, a direction which I assume will be paved with yellow bricks. I am prepared to pay a considerable sum of money (as SATA controller cards go) and so paying anywhere between 60 to 120 dollars will not be an issue whatsoever. Does such a magical device exist? The following link shows an "example" of the type of thing I am looking for, however, I have no way of verifying that once I plug this baby in that my system will still continue to function once I've attached the drives, or that once I've made it to the OS, I will be able to install whatever drivers or software programs I need to make it work with relative ease. It doesn't have to be dog-shit simple, but it cannot involve kernels or brain surgery. http://www.amazon.com/gp/product/B00552PLN4/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B003GSGMPU&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=1HJG60XTZFJ48Z173HKY So does anyone have a suggestion regarding the subject I am asking about? PCI SATA Controller Cards? It would help if you've had experience with the component before - that is after all why I am asking here - for those who have had experience that I do not have. Bear in mind that this is for a home setup and that I do not have a company credit card. I have a budget with a 'relative' upper limit of about $150.00.

    Read the article

< Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >