Search Results

Search found 2282 results on 92 pages for 'filesystem'.

Page 39/92 | < Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >

• Ubuntu "No space left on device" for /home, df shows 100% full, ds shows much, much less

  - by Jon Cram

  On an Ubuntu 12.04 server, normal users can no longer create or add to files in /home, encountering a "No space left on device" error. The /home directory has a capacity of 1.7 terabytes and as far as I can tell is nowhere near full in terms of actual data stored or inodes used. df -h shows: Filesystem Size Used Avail Use% Mounted on /dev/md2 1.0T 18G 955G 2% / udev 7.7G 4.0K 7.7G 1% /dev tmpfs 3.1G 320K 3.1G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.7G 0 7.7G 0% /run/shm cgroup 7.7G 0 7.7G 0% /sys/fs/cgroup /dev/md3 1.7T 1.7T 0 100% /home /dev/md1 496M 45M 426M 10% /boot /home indeed looks rather full. du -hs /home suggests otherwise: 1.4G /home There appears no inode issue - df -i: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/md2 67108864 75334 67033530 1% / udev 2013497 527 2012970 1% /dev tmpfs 2015816 440 2015376 1% /run none 2015816 2 2015814 1% /run/lock none 2015816 1 2015815 1% /run/shm cgroup 2015816 9 2015807 1% /sys/fs/cgroup /dev/md3 113909760 105981 113803779 1% /home /dev/md1 131072 239 130833 1% /boot I recently deleted a many gigabytes of application cache and log data from /home, however this was in the tens of gigabytes at best and nowhere near the capcity of /home. Update 1: du -hs --apparent-size /home 1.2G /home du -hs /home 1.4G /home What might be going on here?

  Read the article

• Bad performance with Linux software RAID5 and LUKS encryption

  - by Philipp Wendler

  I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

  Read the article

• ERROR: Not enough space?

  - by dsmoljanovic

  Now this is a very unspecific question. I'm trying to figure out what this message would mean. Here is the story behind it: I'm installing Oracle enterprise manager cloud control (12c r3) on Solaris 10 (5/09). Installer opens up, i enter all needed information and at the last step click Install. It immediately crashes with only "ERROR: Not enough space" written in log and console and nothing else. Now, this could be java error or Solaris error? I'm thinking it's happening either when it starts to copy files or when it tries to launch a process that would do that. What space is it referring to? disk (have ehough), swap (also), memory (yep)... Any ideas are helpful. Edit: i found this exception in the oraInventory logs: oracle.sysman.oii.oiic.OiicInstallAPIException: Not enough space at oracle.sysman.oii.oiic.OiicAPIInstaller.initInstallSession(OiicAPIInstaller.java:2165) at oracle.sysman.oii.oiic.OiicAPIInstaller.initOUIAPISession(OiicAPIInstaller.java:790) at oracle.sysman.install.oneclick.EMGCOUIInstaller.prepareForInstall(EMGCOUIInstaller.java:676) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext$1.run(EMGCSummaryDlgonNext.java:243) at java.lang.Thread.run(Thread.java:662) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext.actionsOnClickofNext(EMGCSummaryDlgonNext.java:1067) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at oracle.sysman.install.oneclick.EMGCUtil.performonClickOfNextForClass(EMGCUtil.java:399) at oracle.sysman.install.oneclick.EMGCUtil.performPageLevelValidationsForSilentInstall(EMGCUtil.java:367) at oracle.sysman.install.oneclick.EMGCInstaller.prepareForSilentInstall(EMGCInstaller.java:1459) at oracle.sysman.install.oneclick.EMGCInstaller.main(EMGCInstaller.java:1553) disk status: bash-3.00$ df -h /tmp Filesystem size used avail capacity Mounted on swap 8.1G 2.7G 5.4G 33% /tmp bash-3.00$ df -h /u01 Filesystem size used avail capacity Mounted on / 275G 28G 244G 11% / swap: root@gs12emcc # swap -s total: 18306040k bytes allocated + 3837808k reserved = 22143848k used, 5712664k available

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Restoring MBR, partition table, and boot sector of memory card without data loss ("USBC")

  - by Synetech

  Abstract I have a FAT32 memory card that when inserted into a computer causes Windows to prompt to format it. The card is definitely not supposed to be blank and has a bunch of files on it. Symptoms Using a hex-editor/disk-viewer, I examined the card and found that several sectors/clusters have been overwritten with something that has a signature of USBC at the start of the sector. Specifically, the master boot record (and partition table) is gone (hence Windows thinking the card is blank and needing to be formatted), as are the boot sectors (they have the USBC signature and a volume label of NO NAME and partition type of FAT32). Fortunately, it looks like both copies of the FAT are almost entirely intact (a few FAT entries at the start of a cluster here and there seem to be overwritten by USBC). The root directory is also nearly intact—I can see the volume label entry and subdirectory listings, but one sector is overwritten. (There are no more instances of USBC after the last one in the FAT2.) Hypothesis These observations seem to indicate some sort of virus that erases a few key filesystem structures, and then overwrites a few extra sectors here and there. Googling it seems to corroborate the idea of a virus, except that others report a file called USBC which does not apply here, and in fact, could not be possible since there is no filesystem to even see files. I cannot find any information about a virus with these symptoms, nor a removal tool. (I can't help but wonder if it is actually due to an autorun virus prevention tool.) Question I can likely fix the FAT corruption since they are mostly contiguous chains and maybe even the lost sector of the root directory, but does anyone know of a convenient way to restore or (re)create the MBR/partition table and boot sectors (without formatting or overwriting the data)?

  Read the article

• Bonnie does not provide speed for Sequential Input / Block

  - by Lqp1

  I'm using ProxmoxVE and I would like to run some benchmarks regarding performances of this product. One of these benchmarks is bonnie++ ; it runs very well in a VM (qemu-kvm) but when I run it in a conainer (openVZ), it does not provide me reading speed (only writing). I don't understand why... Does anyone know what's happenning ? VMs ans Containers are Debian 7.4. Here's the output of bonnie in the container: root@ct2:/# bonnie++ -u root Using uid:0, gid:0. Writing a byte at a time...done Writing intelligently...done Rewriting...done Reading a byte at a time...done Reading intelligently...done start 'em...done...done...done...done...done... Create files in sequential order...done. Stat files in sequential order...done. Delete files in sequential order...done. Create files in random order...done. Stat files in random order...done. Delete files in random order...done. Version 1.96 ------Sequential Output------ --Sequential Input- --Random- Concurrency 1 -Per Chr- --Block-- -Rewrite- -Per Chr- --Block-- --Seeks-- Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP /sec %CP ct2 1G 843 99 59116 8 60351 4 4966 99 +++++ +++ 2745 8 Latency 9558us 3582ms 527ms 1672us 936us 5248us Version 1.96 ------Sequential Create------ --------Random Create-------- ct2 -Create-- --Read--- -Delete-- -Create-- --Read--- -Delete-- files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP 16 +++++ +++ +++++ +++ +++++ +++ +++++ +++ +++++ +++ +++++ +++ Latency 19567us 358us 368us 107us 59us 25us 1.96,1.96,ct2,1,1401810323,1G,,843,99,59116,8,60351,4,4966,99,+++++,+++,2745,8,16,,,,,+++++,+++,+++++,+++,+++++,+++,+++++,+++,+++++,+++,+++++,+++,9558us,3582ms,527ms,1672us,936us,5248us,19567us,358us,368us,107us,59us,25us The filesystem for / is of type "simfs", which is a pseudo filesystem for openVZ. Maybe it's related to this issue but I can't find anyone with the same issue with bonnie and openVZ... Thanks for your help. Regards, Thomas.

  Read the article

• Debian Wheezy (testing) df reported volume size

  - by TheRoadrunner

  I am a bit confused about the /dev/sda* references since I installed Wheezy instead of Squeeze on a testing box. fdisk -l returns: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e9623 Device Boot Start End Blocks Id System /dev/sda1 * 2048 480278527 240138240 83 Linux /dev/sda2 480280574 488396799 4058113 5 Extended /dev/sda5 480280576 488396799 4058112 82 Linux swap / Solaris This seems correct. But df -h /dev/sda (and /dev/sda1 and /dev/sda2 and /dev/sda5) returns: Filesystem Size Used Avail Use% Mounted on udev 10M 0 10M 0% /dev The same happens with every entry under /dev/disk/by-id and /dev/disk/by-path. Only one of two entries under /dev/disk/by-uuid returns the correct volume size: df -h /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 Filesystem Size Used Avail Use% Mounted on /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 229G 22G 196G 11% / Contents of /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda1 during installation UUID=cacdbad6-7e6b-4e80-84ba-e3c77ef48796 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=45840d13-ee36-4e77-8e73-16cbdff25eb1 none swap sw 0 0 /dev/sr0 /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 It seems all other references than the uuid points to the swap partition. Is this because Wheezy is in testing, and should it be reported as an error?

  Read the article

• Provider claiming "all web servers in the cloud are automatically kept in sync" - should I be skeptical?

  - by RobMasters

  I'm no expert in cloud computing - I've spent a fair bit of time researching it and various providers but am yet to get any hands-on experience with it. From what I've read about AWS and auto-scaling EC2 instances though, it seems as though each instance should be completely decoupled from all other instances. i.e. If content is uploaded to the web server's local filesystem from a custom CMS backend then that content won't be available if subsequently requested from a different web server in the auto-scaling group. Is that right? I met with a representative of our existing hosting provider recently and he was claiming that it isn't a problem that our legacy CMS system is highly dependent on having a local filesystem. He said that all web servers, regardless of how many, would be kept as exact duplicates so I shouldn't notice any difference compared to our existing setup of a single dedicated server. This smells a little too much like bull fecal-matter to me...should I be skeptical about this? I'm a little worried because my (non-technical) boss who ultimately makes the decisions is all for signing up to this cloud solution because it won't require any extra work. I'm sure that they must at least be able to provide this, otherwise they wouldn't be attempting to sell it to us. But at what cost? It sounds as though each web server will always need to be checking the other web server(s) for new static content, which to me sounds like unwanted overhead that'll slow things down. I'd really appreciate it if somebody could clear this up to me. I'm all for switching to AWS and using S3+CloudFront for all static content, but that isn't looking very likely to happen at the moment.

  Read the article

• Unable to resize ec2 ebs root volume

  - by nathanjosiah

  I have followed many of the tutorials that pretty much all say the same thing which is basically: Stop the instance Detach the volume Create a snapshot of the volume Create a bigger volume from the snapshot Attach the new volume to the instance Start the instance back up Run resize2fs /dev/xxx However, step 7 is where the problems start happening. In any case running resize2fs always tells me that it is already xxxxx blocks big and does nothing, even with -f passed. So I start to continue with tutorials which all basically say the same thing and that is: Delete all partitons Recreate them back to what they were except with the bigger sizes Reboot the instance and run resize2fs (I have tried these steps both from the live instance and by attaching the volume to another instance and running the commands there) The main problem is that the instance won't start back up again and the system error log provided in the AWS console doesn't provide any errors. (it does however stop at the grub bootloader which to me indicates that it doesn't like the partitions(yes, the boot flag was toggled on the partition with no affect)) The other thing that happens regardless of what changes I make to the partitions is that the instance that the volume is attached to says that the partition has an invalid magic number and the super-block is corrupt. However, if I make no changes and reattach the volume, the instance runs without a problem. Can anybody shed some light on what I could be doing wrong? Edit On my new volume of 20GB with the 6GB image,df -h says: Filesystem Size Used Avail Use% Mounted on /dev/xvde1 5.8G 877M 4.7G 16% / tmpfs 836M 0 836M 0% /dev/shm And fdisk -l /dev/xvde says: Disk /dev/xvde: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x7d833f39 Device Boot Start End Blocks Id System /dev/xvde1 1 766 6144000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvde2 766 784 146432 82 Linux swap / Solaris Partition 2 does not end on cylinder boundary. Also, sudo resize2fs /dev/xvde1 says: resize2fs 1.41.12 (17-May-2010) The filesystem is already 1536000 blocks long. Nothing to do!

  Read the article

• disk partition centos

  - by FlourishDNA

  I am setting up server for hosting two WordPress which has size of around 70GB. I have already installed CentOS as OS and I would like to partition the Disk. Is there any tool which can help me or can someone guide me though the process as I am not expert is SSH commands. Here are some output that might help. OS: CentOS release 6.3 fdisk -l Disk /dev/xvdb: 214.7 GB, 214748364800 bytes 255 heads, 63 sectors/track, 26108 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b91e0 Device Boot Start End Blocks Id System Disk /dev/xvda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e542c Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/vg_flourish-lv_root: 16.7 GB, 16718495744 bytes 255 heads, 63 sectors/track, 2032 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_flourish-lv_swap: 4227 MB, 4227858432 bytes 255 heads, 63 sectors/track, 514 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 df Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_flourish-lv_root 16070076 758184 14495560 5% / tmpfs 958500 0 958500 0% /dev/shm /dev/xvda1 495844 31926 438318 7% /boot df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_flourish-lv_root 16G 741M 14G 5% / tmpfs 937M 0 937M 0% /dev/shm /dev/xvda1 485M 32M 429M 7% /boot Thanks

  Read the article

• Grub rescue, unknown file system. Can't boot into Windows 7

  - by Sam J

  So, I'm confused, so I'm also going to use this question to get clarification and fix my computer. So, some background: I had Windows 7 on a 1 TB HDD and decided to partition my hard drive into two ~500 GB, one for Windows 7 and one for Ubuntu or whatever flavour I desired (like a sandbox partition...) I installed Ubuntu but the installation had issues so I decided to uninstall. Note before uninstallation I had to press f12 when I turned on to boot from my primary HDD, then choose what OS I wanted to use. Undesirable, but it worked. Anyway, after I decided to uninstall Ubuntu I went into Windows 7 Start Computer Manage and deleted the EXT4 filesystem (Ubuntu parition) giving me 4xx GB of free space. However when I restarted Windows 7, I am now unable to boot Windows. When I DON'T hit f12, I see a blank screen with a flashing underscore. When I DO hit f12, I choose my primary HDD, and then I get a GRUB error: Unknown filesystem: grub rescue _ Something I'm unclear of: GRUB boots linux partitions, right? What boots Windows? Is GRUB "overwriting" the Windows bootloader? How can I completely get Windows back to normal? (IE, It boots automatically without hitting f12.) Thanks for any help, I'm on a live CD version of Ubuntu right now until I can get back on Windows.

  Read the article

• Relinking a deleted file

  - by mbac32768

  Sometimes people delete files they shouldn't, a long-running process still has the file open, and recovering the data by catting /proc/<pid>/fd/N just isn't awesome enough. Awesome enough would be if you could "undo" the delete by running some magic option to ln that would let you re-link to the inode number (recovered through lsof). I can't find any Linux tools to do this, least with cursory Googling. What do you got, serverfault? EDIT1: The reason catting the file from /proc/<pid>/fd/N isn't awesome enough is because the process which still has the file open is still writing to it. A delete removes the reference to the inode from the filesystem namespace. What I want is a way of re-creating the reference. EDIT2: 'debugfs ln' works but the risk is too high since it frobs raw filesystem data. The recovered file is also crazy inconsistent. The link count is zero and I can't add links to it. I'm worse off this way since I can just use /proc/<pid>/fd/N to access the data without corrupting my fs.

  Read the article

• XFS: No space left on device

  - by beketa

  I am using XFS on small HDD (/dev/sdb1, less than 1TB) and storing many small files (-32KB). df -h and -i show that it has available space. # df -hv Filesystem Size Used Avail Use% Mounted on /dev/sda3 127G 19G 102G 16% / tmpfs 16G 0 16G 0% /lib/init/rw udev 16G 168K 16G 1% /dev tmpfs 16G 0 16G 0% /dev/shm /dev/sda1 99M 20M 75M 21% /boot /dev/sdb1 136G 123G 14G 91% /mnt/sdb1 # df -iv Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 8421376 36199 8385177 1% / tmpfs 4126158 5 4126153 1% /lib/init/rw udev 4124934 671 4124263 1% /dev tmpfs 4126158 1 4126157 1% /dev/shm /dev/sda1 26112 222 25890 1% /boot /dev/sdb1 24905120 11076608 13828512 45% /mnt/sdb1 However I got No space left on device error. # touch /mnt/sdb1/test touch: cannot touch `/mnt/sdb1/test': No space left on device I think inode64 issue is not related to this case because drive is less than 1TB and df -i shows that there are free inodes. I unmounted and mounted with -o inode64 but got the same error. xfs_repair does not report any problem. xfs_info shows drive information as follows. # xfs_info /dev/sdb1 meta-data=/dev/sdb1 isize=1024 agcount=16, agsize=2227764 blks = sectsz=512 attr=2 data = bsize=4096 blocks=35644210, imaxpct=25 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0 log =internal bsize=4096 blocks=17404, version=2 = sectsz=512 sunit=0 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 Any ideas? Thanks!

  Read the article

• Assembling Software RAID in Live CD for data recovery

  - by Maletor

  I need help recovering some data that's on my RAID which is on a LVM on my server running Ubuntu. What happened was I deleted the logical volume that controlled my swap space which was on a partition on drives sda2, sdb2, sdc2, and sdd2 in RAID1. This foobared my whole system for one reason or another. Booting leave me with grub rescue and an error saying that it is an unknown filesystem. When I boot to a live cd I can see my RAID arrays and I can even start them up. However, it doesn't appear to mount them anywhere so I can't see the data. I am in the live cd now and I have done sudo apt-get install mdadm lvm2 so it should be mounting them correctly. I just can't see why it wouldn't. Please any help is appreciated here. Here is some output. By the way, there are 3 RAIDs, 1) /boot 100mb RAID1, 2) swap 10gb RAID1, 3) root 990GB RAID5 ubuntu@ubuntu:~$ df -h Filesystem Size Used Avail Use% Mounted on aufs 124M 101M 18M 86% / none 2.0G 324K 2.0G 1% /dev /dev/sde1 2.0G 826M 1.2G 42% /cdrom /dev/loop0 667M 667M 0 100% /rofs none 2.0G 164K 2.0G 1% /dev/shm tmpfs 2.0G 28K 2.0G 1% /tmp none 2.0G 92K 2.0G 1% /var/run none 2.0G 0 2.0G 0% /var/lock none 2.0G 0 2.0G 0% /lib/init/rw /dev/md1 91M 73M 15M 84% /media/5ac3dbf1-a6c5-409c-96ae-edc6e27992c7 ubuntu@ubuntu:~$ cat /etc/fstab aufs / aufs rw 0 0 tmpfs /tmp tmpfs nosuid,nodev 0 0 /dev/sda2 swap swap defaults 0 0 /dev/sdb2 swap swap defaults 0 0 /dev/sdc2 swap swap defaults 0 0 /dev/sdd2 swap swap defaults 0 0

  Read the article

• How to make a redundant desktop system with daily snapshots? (Is btrfs ready for use?)

  - by TestUser16418

  I want to configure a desktop system in which the home filesystem would be redundant (e.g. RAID-1), and would have weekly snapshots taken. I've already done this with ZFS, the snapshot system is wonderful, and with send/recv you can easily create backups on external media. Unfortunately, at that point, I want GNU+Linux and not FreeBSD or Solaris, so I'm looking for suggestions for good alternatives. I reckon that my alternatives are: btrfs - it seems to be exactly what I need, it has snapshots and commands that allow you to easily replicate zfs send. Yet all documentation mentions that it's still experimental. I can't seem to find any actual reports on its reliability or usability issues. Can you point me to any information on that issue that could clarify whether it would be a possible choice? I have a large preference for this option, mostly because I don't want to reformat the drives when btrfs becomes ready, but I there's no information on whether it's usable at all, whether it's a silly idea to use it, etc. The question that I cannot get the answer to is what does "experimental" mean. lvm snapshots and ext4 - preferably not, since it can consume an awful amount of space when new files are created. Creating 200 GB files requres 200 GB free space and 200 GB additionally for snapshots. I also have found it unreliable -- failed metadata rewrite results in an unreadable PV. I'm wondering how btrfs would compare here. A single filesystem (ext4) on a RAID-1 array with custom COW snapshots with hardlinks (like cp -al). That's my current preference if I can't use btrfs. So how experimental btrfs is, which should I choose, and do I have any other options? What if I don't keep external incremental backups, would that affect my choice?

  Read the article

• Disk (EXT4) suddenly empty without any sign of why

  - by Ohnomydisk

  I have a Ubuntu 10.04 server with several disks in it. The disks are setup with a union filesystem, which presents them all as one logical /home. A few days ago, one of the disks appears to have suddenly 'become empty', for lack of better explanation. The amount of data on the /home mount almost halved within minutes - the disk appears to have had just over 400 GB of data prior to 'becoming empty'. I have absolutely no idea what happened. I was not using the server at the other time, but there are half a dozen other users who may have been (without root access and without the ability to hose a whole disk). I've ran SMART tests on the disk and it comes back clean. The filesystem checks fine (it has 12 GB used now, as some user software continued downloading after the incident). All I know is that around around midnight on October 19, the disk usage changed dramatically: The data points are every 15 minutes, and the full loss occured between captures: 2012-10-18 23:58:03.399647 - has 953.97/2059.07 GB [46.33 percent] 2012-10-19 00:13:15.909010 - has 515.18/2059.07 GB [25.02 percent] Other than that, I have not much to go off :-( I know that: There's nothing interesting in log files at that time Nobody appeared to be logged in via SSH at the time it occured (most users do not even use SSH) The server was online through whatever occured (3 months uptime) None of the other disks were affected and everything else on the server looks completely normal I have tried using "extundelete" on the disk and it didn't really find anything (some temporary files, but they looked new anyway) I am completely at a loss to what could have caused this. I was initially thinking maybe root escalation exploit, but even if someone did maliciously "rm" the disk contents, it would take more than 15 minutes for 400 GB?

  Read the article

• Is it safe to format this partition?

  - by xanesis4

  On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

  Read the article

• ?Exadata??????DBFS

  - by Liu Maclean(???)

  ?Exadata???DBFS ??????? 1. ??fuse RPM  [root@dm01db01 ~]# yum install fuse Loaded plugins: rhnplugin, security This system is not registered with ULN. ULN support will be disabled. Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package fuse.x86_64 0:2.7.4-8.0.1.el5 set to be updated --> Finished Dependency Resolution Dependencies Resolved ========================================================================================================================================================================  Package                            Arch                                 Version                                         Repository                                Size ======================================================================================================================================================================== Installing:  fuse                               x86_64                               2.7.4-8.0.1.el5                                 el5_latest                                85 k Transaction Summary ======================================================================================================================================================================== Install       1 Package(s) Upgrade       0 Package(s) Total download size: 85 k Is this ok [y/N]: y Downloading Packages: fuse-2.7.4-8.0.1.el5.x86_64.rpm                                                                                                                  |  85 kB     00:00      Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Test Succeeded Running Transaction   Installing     : fuse                                                                                                                                             1/1  Installed:   fuse.x86_64 0:2.7.4-8.0.1.el5                                                                                                                                          [root@dm01db01 ~]# yum install fuse-libs Loaded plugins: rhnplugin, security This system is not registered with ULN. ULN support will be disabled. Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package fuse-libs.i386 0:2.7.4-8.0.1.el5 set to be updated ---> Package fuse-libs.x86_64 0:2.7.4-8.0.1.el5 set to be updated --> Finished Dependency Resolution Dependencies Resolved ========================================================================================================================================================================  Package                                Arch                                Version                                       Repository                               Size ======================================================================================================================================================================== Installing:  fuse-libs                              i386                                2.7.4-8.0.1.el5                               el5_latest                               71 k  fuse-libs                              x86_64                              2.7.4-8.0.1.el5                               el5_latest                               70 k Transaction Summary ======================================================================================================================================================================== Install       2 Package(s) Upgrade       0 Package(s) Total download size: 141 k Is this ok [y/N]: y Downloading Packages: (1/2): fuse-libs-2.7.4-8.0.1.el5.x86_64.rpm                                                                                                      |  70 kB     00:00      (2/2): fuse-libs-2.7.4-8.0.1.el5.i386.rpm                                                                                                        |  71 kB     00:00      ------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Total                                                                                                                                    71 kB/s | 141 kB     00:01      Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Test Succeeded Running Transaction   Installing     : fuse-libs                                                                                                                                        1/2    Installing     : fuse-libs                                                                                                                                        2/2  Installed:   fuse-libs.i386 0:2.7.4-8.0.1.el5                                                  fuse-libs.x86_64 0:2.7.4-8.0.1.el5                                                  Complete! [root@dm01db01 ~]# yum install fuse-devel Loaded plugins: rhnplugin, security This system is not registered with ULN. ULN support will be disabled. Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package fuse-devel.i386 0:2.7.4-8.0.1.el5 set to be updated ---> Package fuse-devel.x86_64 0:2.7.4-8.0.1.el5 set to be updated --> Finished Dependency Resolution Dependencies Resolved ========================================================================================================================================================================  Package                                 Arch                                Version                                      Repository                               Size ======================================================================================================================================================================== Installing:  fuse-devel                              i386                                2.7.4-8.0.1.el5                              el5_latest                               28 k  fuse-devel                              x86_64                              2.7.4-8.0.1.el5                              el5_latest                               28 k Transaction Summary ======================================================================================================================================================================== Install       2 Package(s) Upgrade       0 Package(s) Total download size: 57 k Is this ok [y/N]: y Downloading Packages: (1/2): fuse-devel-2.7.4-8.0.1.el5.x86_64.rpm                                                                                                     |  28 kB     00:00      (2/2): fuse-devel-2.7.4-8.0.1.el5.i386.rpm                                                                                                       |  28 kB     00:00      ------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Total                                                                                                                                    21 kB/s |  57 kB     00:02      Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Test Succeeded Running Transaction   Installing     : fuse-devel                                                                                                                                       1/2    Installing     : fuse-devel                                                                                                                                       2/2  Installed:   fuse-devel.i386 0:2.7.4-8.0.1.el5                                                 fuse-devel.x86_64 0:2.7.4-8.0.1.el5                                                 Complete! 2. ?? DBFS??? ?????? cd $ORACLE_HOME/rdbms/admin sqlplus / as sysdba Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Partitioning, Real Application Clusters, Automatic Storage Management, OLAP, Data Mining and Real Application Testing options SQL> @prvtfspi.plb Package body created. No errors. Package body created. No errors. ?????dbms_dbfs_sfs package  SQL> create tablespace dbfstbs datafile size 20g; Tablespace created. SQL> create user maclean_dbfs identified by oracle; User created. SQL> grant dba to maclean_dbfs; Grant succeeded. @@!!! SQL> grant  dbfs_role to maclean_dbfs; Grant succeeded. 3. ??DBFS SQL> conn maclean_dbfs/oracle Connected. SQL> @?/rdbms/admin/dbfs_create_filesystem.sql  dbfstbs mac_dbfs   No errors. -------- CREATE STORE: begin dbms_dbfs_sfs.createFilesystem(store_name => 'FS_MAC_DBFS', tbl_name => 'T_MAC_DBFS', tbl_tbs => 'dbfstbs', lob_tbs => 'dbfstbs', do_partition => false, partition_key => 1, do_compress => false, compression => '', do_dedup => false, do_encrypt => false); end; -------- REGISTER STORE: begin dbms_dbfs_content.registerStore(store_name=> 'FS_MAC_DBFS', provider_name => 'sample1', provider_package => 'dbms_dbfs_sfs'); end; -------- MOUNT STORE: begin dbms_dbfs_content.mountStore(store_name=>'FS_MAC_DBFS', store_mount=>'mac_dbfs'); end; -------- CHMOD STORE: declare m integer; begin m := dbms_fuse.fs_chmod('/mac_dbfs', 16895); end; No errors. 4.  ??mount point  [root@dm01db01 ~]# mkdir /dbfs [root@dm01db01 ~]# chown oracle:oinstall /dbfs 5. ??library path ?OS  # echo "/usr/local/lib" >> /etc/ld.so.conf.d/usr_local_lib.conf 6. ?????? export ORACLE_HOME=/s01/orabase/product/11.2.0/dbhome_1 [root@dm01db01 ~]# ln -s $ORACLE_HOME/lib/libclntsh.so.11.1 /usr/local/lib/libclntsh.so.11.1 [root@dm01db01 ~]#  ln -s $ORACLE_HOME/lib/libnnz11.so /usr/local/lib/libnnz11.so [root@dm01db01 ~]#  ln -s /lib64/libfuse.so.2 /usr/local/lib/libfuse.so.2 7. ??ldconfig  [root@dm01db01 ~]# ldconfig [root@dm01db01 ~]#  8. ??fusermount??????? [root@dm01db01 ~]#  chmod +x /usr/bin/fusermount [root@dm01db01 ~]#  ls -l /usr/bin/fusermount lrwxrwxrwx 1 root root 15 Sep  7 03:06 /usr/bin/fusermount -> /bin/fusermount [root@dm01db01 ~]#  ls -l /bin/fusermount -rwsr-x--x 1 root fuse 27072 Oct 17  2011 /bin/fusermount 9. ???????OS  dbfs_client maclean_dbfs@dm01db01:1521/orcl  /dbfs 10. ????nohup + &?????mount DBFS,???????????? [oracle@dm01db01 ~]$ echo "oracle"  >> dbfs_pw [oracle@dm01db01 ~]$ nohup dbfs_client maclean_dbfs@dm01db01:1521/orcl /dbfs < dbfs_pw & [oracle@dm01db01 ~]$ df -h Filesystem            Size  Used Avail Use% Mounted on /dev/mapper/VGExaDb-LVDbSys1                        30G   15G   14G  53% / /dev/sda1             502M   30M  447M   7% /boot /dev/mapper/VGExaDb-LVDbOra1                        99G   20G   75G  21% /u01 tmpfs                  81G     0   81G   0% /dev/shm dbfs-maclean_dbfs@orcl:/                        20G  120K   20G   1% /dbfs [oracle@dm01db01 ~]$ mount /dev/mapper/VGExaDb-LVDbSys1 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda1 on /boot type ext3 (rw,nodev) /dev/mapper/VGExaDb-LVDbOra1 on /u01 type ext3 (rw,nodev) tmpfs on /dev/shm type tmpfs (rw,size=82052m) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) dbfs-maclean_dbfs@orcl:/ on /dbfs type fuse (rw,nosuid,nodev,max_read=1048576,default_permissions,user=oracle) [oracle@dm01db01 ~]$ ls -l /dbfs/ total 0 drwxrwxrwx 3 root root 0 Sep 14 05:11 mac_dbfs [oracle@nas ~]$ dbfs_client  --------MOUNT mode: usage: dbfs_client <db_user>@<db_server> [options] <mountpoint>   db_user:              Name of Database user that owns DBFS content repository filesystem(s)   db_server:            A valid connect string for Oracle database server                         (for example, hrdb_host:1521/hrservice)   mountpoint:           Path to mount Database File System(s)                         All the file systems owned by the database user will be seen at the mountpoint. DBFS options:   -o direct_io          Bypass the Linux page cache. Gives much better performance for large files.                         Programs in the file system cannot be executed with this option.                         This option is recommended when DBFS is used as an ETL staging area.   -o wallet             Run dbfs_client in background.                         Wallet must be configured to get credentials.   -o failover           dbfs_client fails over to surviving database instance with no data loss.                         Some performance cost on writes, especially for small files.   -o allow_root         Allows root access to the filesystem.                         This option requires setting 'user_allow_other' parameter in '/etc/fuse.conf'.   -o allow_other        Allows other users access to the file system.                         This option requires setting 'user_allow_other' parameter in '/etc/fuse.conf'.   -o rw                 Mount the filesystem read-write. [Default]   -o ro                 Mount the filesystem read-only. Files cannot be modified.   -o trace_file=STR     Tracing <filename> | 'syslog'   -o trace_level=N      Trace Level: 1->DEBUG, 2->INFO, 3->WARNING, 4->ERROR, 5->CRITICAL [Default: 4]   -h                    help   -V                    version --------COMMAND mode: Usage:     dbfs_client <db_user>@<db_server> --command command [switches] [arguments]             command:          Command to be executed, e.g., ls, cp, mkdir, rm            switches:         Switches are described below for each command.            arguments:        File names or directory names NOTE:      All database pathnames must be absolute and preceded by dbfs:/ Commands   ls            dbfs_client <db_user>@<db_server> --command ls [switches] target      Switches:              -a         Show all files including those starting with '.'            -l         Use a long listing format. In addition to the name of each file                       print the file type, permissions, size, user and group information            -R         List subdirectories recursively cp                     dbfs_client <db_user>@<db_server> --command cp [switches] source destination      Switches:              -r, -R      Copy a directory and its contents recursively into the destination directory rm                     dbfs_client <db_user>@<db_server> --command rm [switches] target      Switches:              -r, -R      Removes a directory and its contents recursively mkdir                  dbfs_client <db_user>@<db_server> --command mkdir directory_name Examples                     dbfs_client ETLUser@DBConnectString --command ls -l -a dbfs:/staging_area/directory1            dbfs_client ETLUser@DBConnectString --command cp -R  /tmp/1-Jan-2009-dump dbfs:/staging_area            dbfs_client ETLUser@DBConnectString --command rm dbfs:/staging_area/hello.txt            dbfs_client ETLUser@DBConnectString --command mkdir dbfs:/staging_area/directory2 [oracle@dm01db01 ~]$ ls -lh /tmp/largefile -rw-r--r-- 1 oracle oinstall 2.0G Sep 14 08:50 /tmp/largefile [oracle@dm01db01 ~]$ time dbfs_client  maclean_dbfs@dm01db01:1521/orcl --command cp /tmp/largefile dbfs:/mac_dbfs Password: /tmp/largefile -> dbfs:/mac_dbfs/largefile real    0m11.802s user    0m0.580s sys     0m2.375s ?Exadata?????2G?????? DBFS???11s => 200MB/s 

  Read the article

• fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

  - by d0nd

  Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

  Read the article

• Mount TMPFS instead of ro /dev

  - by schiggn

  I am working on a ARM-Based embedded system with a custom Debian Linux based on kernel 2.6.31. In the final system, the Root file system is stored as squashfs on flash. Now, the folder /dev is created by udev, but since there is no hot plugging functionality needed and booting time is critical, I wanted to delete udev and "hard code" the /dev folder (read here, page 5). because i still need to change parameters of the devices (with ioctl /sysfs) this does not work for me in this case. so i thought of mounting a tmpfs on /dev and change the parameters there. is this possible? and how to do best? my approach would be: delete /dev from RFS create tar containing basic devices mount tmpfs /dev untar tar-file into /dev change parameters Could this work? Do you see any problems? I found out, that you can mount on top of already mounted mount point, is it somehow possible just to take data with while mounting the new file system? if so that would be very convenient! Thanks Update: I just tried that out, but I'm stuck at a certain point. I packed all my devices into devices.tar, packed it into /usr of my squashfs and added the following lines to mountkernfs.sh, which is executed right after INIT. #mount /dev on tmpfs echo -n "Mounting /dev on tmpfs..." mount -o size=5M,mode=0755 -t tmpfs tmpfs /dev mknod -m 600 /dev/console c 5 1 mknod -m 600 /dev/null c 1 3 echo "done." echo -n "Populating /dev..." tar -xf /usr/devices.tar -C /dev echo "done." This works fine on the version over NFS, if I place printf's in the code, I can see it executing, if I comment out the extracting part, its complaining about missing devices. Booting OK mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. System Clock set to: Thu Sep 13 11:26:23 UTC 2012. INIT: Entering runlevel: 2 UBI: attaching mtd8 to ubi0 Commenting out the extraction of the tar mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Thu Sep 13 12:24:00 UTC 2012 ... (warning). INIT: Entering runlevel: 2 libubi: error!: cannot open "/dev/ubi_ctrl" So far so good. But if I pack the whole story into a squashfs and boot from there, it is acting strange. It's telling me while booting that it is unable to open an initial console and its throwing errors on mounting the UBIFS devices, but finally provides a login anyway. Over that my echo's are not executed. If I then log in, /dev is mounted as TMPFS as desired and all the devices reside inside. When I redo the "mount" command to mount the UBIFS partitions it is executed whitout problem and useable. From squashfs VFS: Mounted root (squashfs filesystem) readonly on device 31:15. Freeing init memory: 136K Warning: unable to open an initial console. mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 UBIFS error (pid 484): ubifs_get_sb: cannot open "ubi1_0", error -19 Additionally, a part of the rest of the bootscripts is still exexuted, but not all of them. Does anyone has a clue why? Other question, is 5MB enough/too much for /dev?

  Read the article

• How to mount a blu-ray drive?

  - by Stephan Schielke

  Maybe it is for the best to close this question. This has nothing to do with a bluray drive in general anymore. Probably a hardware defect. I will try to test it with a windows system and different cables again... Thx so far. I have a bluray/dvd/cdrom drive with SATA. Ubuntu wont find it under /dev/sd wodim --devices wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg2' rwrw-- : 'HL-DT-ST' 'BDDVDRW CH08LS10' ------------------------------------------------------------------------- cdrecord -scanbus scsibus2: 2,0,0 200) 'HL-DT-ST' 'BDDVDRW CH08LS10' '2.00' Removable CD-ROM fdisk dont even lists it. Ubuntu only automounts blank DVDs, but neither CDROM nor Blurays. I also changed the sata slot, sata cable and the power cable. The drive works with a windows system. This happens when I try to mount: sudo mount -t auto /dev/scd0 /media/bluray mount: you must specify the filesystem type I tried all filesystems there are. I also installed makemkv. It finds the drive but not the disc. Here is my /dev ls -al /dev total 12 drwxr-xr-x 17 root root 4420 2011-11-25 19:36 . drwxr-xr-x 28 root root 4096 2011-11-25 07:12 .. crw------- 1 root root 10, 235 2011-11-25 19:28 autofs -rw-r--r-- 1 root root 630 2011-11-25 19:28 .blkid.tab -rw-r--r-- 1 root root 630 2011-11-25 19:28 .blkid.tab.old drwxr-xr-x 2 root root 700 2011-11-25 19:27 block drwxr-xr-x 2 root root 100 2011-11-25 19:27 bsg crw------- 1 root root 10, 234 2011-11-25 19:28 btrfs-control drwxr-xr-x 3 root root 60 2011-11-25 19:27 bus drwxr-xr-x 2 root root 3820 2011-11-25 19:28 char crw------- 1 root root 5, 1 2011-11-25 19:28 console lrwxrwxrwx 1 root root 11 2011-11-25 19:28 core -> /proc/kcore drwxr-xr-x 2 root root 60 2011-11-25 19:28 cpu crw------- 1 root root 10, 60 2011-11-25 19:28 cpu_dma_latency drwxr-xr-x 7 root root 140 2011-11-25 19:27 disk crw------- 1 root root 10, 61 2011-11-25 19:28 ecryptfs crw-rw---- 1 root video 29, 0 2011-11-25 19:28 fb0 lrwxrwxrwx 1 root root 13 2011-11-25 19:28 fd -> /proc/self/fd crw-rw-rw- 1 root root 1, 7 2011-11-25 19:28 full crw-rw-rw- 1 root fuse 10, 229 2011-11-25 19:28 fuse crw------- 1 root root 251, 0 2011-11-25 19:28 hidraw0 crw------- 1 root root 251, 1 2011-11-25 19:28 hidraw1 crw------- 1 root root 10, 228 2011-11-25 19:28 hpet lrwxrwxrwx 1 root root 14 2011-11-25 19:27 .initramfs -> /run/initramfs drwxr-xr-x 4 root root 220 2011-11-25 19:28 input crw------- 1 root root 1, 11 2011-11-25 19:28 kmsg srw-rw-rw- 1 root root 0 2011-11-25 19:28 log brw-rw---- 1 root disk 7, 0 2011-11-25 19:28 loop0 brw-rw---- 1 root disk 7, 1 2011-11-25 19:28 loop1 brw-rw---- 1 root disk 7, 2 2011-11-25 19:28 loop2 brw-rw---- 1 root disk 7, 3 2011-11-25 19:28 loop3 brw-rw---- 1 root disk 7, 4 2011-11-25 19:28 loop4 brw-rw---- 1 root disk 7, 5 2011-11-25 19:28 loop5 brw-rw---- 1 root disk 7, 6 2011-11-25 19:28 loop6 brw-rw---- 1 root disk 7, 7 2011-11-25 19:28 loop7 drwxr-xr-x 2 root root 60 2011-11-25 19:27 mapper crw------- 1 root root 10, 227 2011-11-25 19:28 mcelog crw-r----- 1 root kmem 1, 1 2011-11-25 19:28 mem drwxr-xr-x 2 root root 60 2011-11-25 19:27 net crw------- 1 root root 10, 59 2011-11-25 19:28 network_latency crw------- 1 root root 10, 58 2011-11-25 19:28 network_throughput crw-rw-rw- 1 root root 1, 3 2011-11-25 19:28 null crw-rw-rw- 1 root root 195, 0 2011-11-25 19:28 nvidia0 crw-rw-rw- 1 root root 195, 255 2011-11-25 19:28 nvidiactl crw------- 1 root root 1, 12 2011-11-25 19:28 oldmem crw-r----- 1 root kmem 1, 4 2011-11-25 19:28 port crw------- 1 root root 108, 0 2011-11-25 19:28 ppp crw------- 1 root root 10, 1 2011-11-25 19:28 psaux crw-rw-rw- 1 root tty 5, 2 2011-11-25 20:00 ptmx drwxr-xr-x 2 root root 0 2011-11-25 19:27 pts brw-rw---- 1 root disk 1, 0 2011-11-25 19:28 ram0 brw-rw---- 1 root disk 1, 1 2011-11-25 19:28 ram1 brw-rw---- 1 root disk 1, 10 2011-11-25 19:28 ram10 brw-rw---- 1 root disk 1, 11 2011-11-25 19:28 ram11 brw-rw---- 1 root disk 1, 12 2011-11-25 19:28 ram12 brw-rw---- 1 root disk 1, 13 2011-11-25 19:28 ram13 brw-rw---- 1 root disk 1, 14 2011-11-25 19:28 ram14 brw-rw---- 1 root disk 1, 15 2011-11-25 19:28 ram15 brw-rw---- 1 root disk 1, 2 2011-11-25 19:28 ram2 brw-rw---- 1 root disk 1, 3 2011-11-25 19:28 ram3 brw-rw---- 1 root disk 1, 4 2011-11-25 19:28 ram4 brw-rw---- 1 root disk 1, 5 2011-11-25 19:28 ram5 brw-rw---- 1 root disk 1, 6 2011-11-25 19:28 ram6 brw-rw---- 1 root disk 1, 7 2011-11-25 19:28 ram7 brw-rw---- 1 root disk 1, 8 2011-11-25 19:28 ram8 brw-rw---- 1 root disk 1, 9 2011-11-25 19:28 ram9 crw-rw-rw- 1 root root 1, 8 2011-11-25 19:28 random crw-rw-r--+ 1 root root 10, 62 2011-11-25 19:28 rfkill lrwxrwxrwx 1 root root 4 2011-11-25 19:28 rtc -> rtc0 crw------- 1 root root 254, 0 2011-11-25 19:28 rtc0 lrwxrwxrwx 1 root root 3 2011-11-25 19:38 scd0 -> sr0 brw-rw---- 1 root disk 8, 0 2011-11-25 19:28 sda brw-rw---- 1 root disk 8, 1 2011-11-25 19:28 sda1 brw-rw---- 1 root disk 8, 2 2011-11-25 19:28 sda2 brw-rw---- 1 root disk 8, 3 2011-11-25 19:28 sda3 brw-rw---- 1 root disk 8, 5 2011-11-25 19:28 sda5 brw-rw---- 1 root disk 8, 6 2011-11-25 19:28 sda6 brw-rw---- 1 root disk 8, 16 2011-11-25 19:28 sdb brw-rw---- 1 root disk 8, 17 2011-11-25 19:28 sdb1 crw-rw---- 1 root disk 21, 0 2011-11-25 19:28 sg0 crw-rw---- 1 root disk 21, 1 2011-11-25 19:28 sg1 crw-rw----+ 1 root cdrom 21, 2 2011-11-25 19:28 sg2 lrwxrwxrwx 1 root root 8 2011-11-25 19:28 shm -> /run/shm crw------- 1 root root 10, 231 2011-11-25 19:28 snapshot drwxr-xr-x 4 root root 280 2011-11-25 19:28 snd brw-rw----+ 1 root cdrom 11, 0 2011-11-25 19:38 sr0 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stderr -> /proc/self/fd/2 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stdin -> /proc/self/fd/0 lrwxrwxrwx 1 root root 15 2011-11-25 19:28 stdout -> /proc/self/fd/1 crw-rw-rw- 1 root tty 5, 0 2011-11-25 19:35 tty crw--w---- 1 root tty 4, 0 2011-11-25 19:28 tty0 crw------- 1 root root 4, 1 2011-11-25 19:28 tty1 crw--w---- 1 root tty 4, 10 2011-11-25 19:28 tty10 crw--w---- 1 root tty 4, 11 2011-11-25 19:28 tty11 crw--w---- 1 root tty 4, 12 2011-11-25 19:28 tty12 crw--w---- 1 root tty 4, 13 2011-11-25 19:28 tty13 crw--w---- 1 root tty 4, 14 2011-11-25 19:28 tty14 crw--w---- 1 root tty 4, 15 2011-11-25 19:28 tty15 crw--w---- 1 root tty 4, 16 2011-11-25 19:28 tty16 crw--w---- 1 root tty 4, 17 2011-11-25 19:28 tty17 crw--w---- 1 root tty 4, 18 2011-11-25 19:28 tty18 crw--w---- 1 root tty 4, 19 2011-11-25 19:28 tty19 crw------- 1 root root 4, 2 2011-11-25 19:28 tty2 crw--w---- 1 root tty 4, 20 2011-11-25 19:28 tty20 crw--w---- 1 root tty 4, 21 2011-11-25 19:28 tty21 crw--w---- 1 root tty 4, 22 2011-11-25 19:28 tty22 crw--w---- 1 root tty 4, 23 2011-11-25 19:28 tty23 crw--w---- 1 root tty 4, 24 2011-11-25 19:28 tty24 crw--w---- 1 root tty 4, 25 2011-11-25 19:28 tty25 crw--w---- 1 root tty 4, 26 2011-11-25 19:28 tty26 crw--w---- 1 root tty 4, 27 2011-11-25 19:28 tty27 crw--w---- 1 root tty 4, 28 2011-11-25 19:28 tty28 crw--w---- 1 root tty 4, 29 2011-11-25 19:28 tty29 crw------- 1 root root 4, 3 2011-11-25 19:28 tty3 crw--w---- 1 root tty 4, 30 2011-11-25 19:28 tty30 crw--w---- 1 root tty 4, 31 2011-11-25 19:28 tty31 crw--w---- 1 root tty 4, 32 2011-11-25 19:28 tty32 crw--w---- 1 root tty 4, 33 2011-11-25 19:28 tty33 crw--w---- 1 root tty 4, 34 2011-11-25 19:28 tty34 crw--w---- 1 root tty 4, 35 2011-11-25 19:28 tty35 crw--w---- 1 root tty 4, 36 2011-11-25 19:28 tty36 crw--w---- 1 root tty 4, 37 2011-11-25 19:28 tty37 crw--w---- 1 root tty 4, 38 2011-11-25 19:28 tty38 crw--w---- 1 root tty 4, 39 2011-11-25 19:28 tty39 crw------- 1 root root 4, 4 2011-11-25 19:28 tty4 crw--w---- 1 root tty 4, 40 2011-11-25 19:28 tty40 crw--w---- 1 root tty 4, 41 2011-11-25 19:28 tty41 crw--w---- 1 root tty 4, 42 2011-11-25 19:28 tty42 crw--w---- 1 root tty 4, 43 2011-11-25 19:28 tty43 crw--w---- 1 root tty 4, 44 2011-11-25 19:28 tty44 crw--w---- 1 root tty 4, 45 2011-11-25 19:28 tty45 crw--w---- 1 root tty 4, 46 2011-11-25 19:28 tty46 crw--w---- 1 root tty 4, 47 2011-11-25 19:28 tty47 crw--w---- 1 root tty 4, 48 2011-11-25 19:28 tty48 crw--w---- 1 root tty 4, 49 2011-11-25 19:28 tty49 crw------- 1 root root 4, 5 2011-11-25 19:28 tty5 crw--w---- 1 root tty 4, 50 2011-11-25 19:28 tty50 crw--w---- 1 root tty 4, 51 2011-11-25 19:28 tty51 crw--w---- 1 root tty 4, 52 2011-11-25 19:28 tty52 crw--w---- 1 root tty 4, 53 2011-11-25 19:28 tty53 crw--w---- 1 root tty 4, 54 2011-11-25 19:28 tty54 crw--w---- 1 root tty 4, 55 2011-11-25 19:28 tty55 crw--w---- 1 root tty 4, 56 2011-11-25 19:28 tty56 crw--w---- 1 root tty 4, 57 2011-11-25 19:28 tty57 crw--w---- 1 root tty 4, 58 2011-11-25 19:28 tty58 crw--w---- 1 root tty 4, 59 2011-11-25 19:28 tty59 crw------- 1 root root 4, 6 2011-11-25 19:28 tty6 crw--w---- 1 root tty 4, 60 2011-11-25 19:28 tty60 crw--w---- 1 root tty 4, 61 2011-11-25 19:28 tty61 crw--w---- 1 root tty 4, 62 2011-11-25 19:28 tty62 crw--w---- 1 root tty 4, 63 2011-11-25 19:28 tty63 crw--w---- 1 root tty 4, 7 2011-11-25 19:28 tty7 crw--w---- 1 root tty 4, 8 2011-11-25 19:28 tty8 crw--w---- 1 root tty 4, 9 2011-11-25 19:28 tty9 crw------- 1 root root 5, 3 2011-11-25 19:28 ttyprintk crw-rw---- 1 root dialout 4, 64 2011-11-25 19:28 ttyS0 crw-rw---- 1 root dialout 4, 65 2011-11-25 19:28 ttyS1 crw-rw---- 1 root dialout 4, 74 2011-11-25 19:28 ttyS10 crw-rw---- 1 root dialout 4, 75 2011-11-25 19:28 ttyS11 crw-rw---- 1 root dialout 4, 76 2011-11-25 19:28 ttyS12 crw-rw---- 1 root dialout 4, 77 2011-11-25 19:28 ttyS13 crw-rw---- 1 root dialout 4, 78 2011-11-25 19:28 ttyS14 crw-rw---- 1 root dialout 4, 79 2011-11-25 19:28 ttyS15 crw-rw---- 1 root dialout 4, 80 2011-11-25 19:28 ttyS16 crw-rw---- 1 root dialout 4, 81 2011-11-25 19:28 ttyS17 crw-rw---- 1 root dialout 4, 82 2011-11-25 19:28 ttyS18 crw-rw---- 1 root dialout 4, 83 2011-11-25 19:28 ttyS19 crw-rw---- 1 root dialout 4, 66 2011-11-25 19:28 ttyS2 crw-rw---- 1 root dialout 4, 84 2011-11-25 19:28 ttyS20 crw-rw---- 1 root dialout 4, 85 2011-11-25 19:28 ttyS21 crw-rw---- 1 root dialout 4, 86 2011-11-25 19:28 ttyS22 crw-rw---- 1 root dialout 4, 87 2011-11-25 19:28 ttyS23 crw-rw---- 1 root dialout 4, 88 2011-11-25 19:28 ttyS24 crw-rw---- 1 root dialout 4, 89 2011-11-25 19:28 ttyS25 crw-rw---- 1 root dialout 4, 90 2011-11-25 19:28 ttyS26 crw-rw---- 1 root dialout 4, 91 2011-11-25 19:28 ttyS27 crw-rw---- 1 root dialout 4, 92 2011-11-25 19:28 ttyS28 crw-rw---- 1 root dialout 4, 93 2011-11-25 19:28 ttyS29 crw-rw---- 1 root dialout 4, 67 2011-11-25 19:28 ttyS3 crw-rw---- 1 root dialout 4, 94 2011-11-25 19:28 ttyS30 crw-rw---- 1 root dialout 4, 95 2011-11-25 19:28 ttyS31 crw-rw---- 1 root dialout 4, 68 2011-11-25 19:28 ttyS4 crw-rw---- 1 root dialout 4, 69 2011-11-25 19:28 ttyS5 crw-rw---- 1 root dialout 4, 70 2011-11-25 19:28 ttyS6 crw-rw---- 1 root dialout 4, 71 2011-11-25 19:28 ttyS7 crw-rw---- 1 root dialout 4, 72 2011-11-25 19:28 ttyS8 crw-rw---- 1 root dialout 4, 73 2011-11-25 19:28 ttyS9 d rwxr-xr-x 3 root root 60 2011-11-25 19:28 .udev crw-r----- 1 root root 10, 223 2011-11-25 19:28 uinput crw-rw-rw- 1 root root 1, 9 2011-11-25 19:28 urandom drwxr-xr-x 2 root root 60 2011-11-25 19:27 usb crw------- 1 root root 252, 0 2011-11-25 19:28 usbmon0 crw------- 1 root root 252, 1 2011-11-25 19:28 usbmon1 crw------- 1 root root 252, 2 2011-11-25 19:28 usbmon2 crw------- 1 root root 252, 3 2011-11-25 19:28 usbmon3 crw------- 1 root root 252, 4 2011-11-25 19:28 usbmon4 crw------- 1 root root 252, 5 2011-11-25 19:28 usbmon5 crw------- 1 root root 252, 6 2011-11-25 19:28 usbmon6 crw------- 1 root root 252, 7 2011-11-25 19:28 usbmon7 crw------- 1 root root 252, 8 2011-11-25 19:28 usbmon8 drwxr-xr-x 4 root root 80 2011-11-25 19:28 v4l crw------- 1 root root 10, 57 2011-11-25 19:28 vboxdrv crw------- 1 root root 10, 56 2011-11-25 19:28 vboxnetctl drwxr-x--- 4 root vboxusers 80 2011-11-25 19:28 vboxusb crw-rw---- 1 root tty 7, 0 2011-11-25 19:28 vcs crw-rw---- 1 root tty 7, 1 2011-11-25 19:28 vcs1 crw-rw---- 1 root tty 7, 2 2011-11-25 19:28 vcs2 crw-rw---- 1 root tty 7, 3 2011-11-25 19:28 vcs3 crw-rw---- 1 root tty 7, 4 2011-11-25 19:28 vcs4 crw-rw---- 1 root tty 7, 5 2011-11-25 19:28 vcs5 crw-rw---- 1 root tty 7, 6 2011-11-25 19:28 vcs6 crw-rw---- 1 root tty 7, 128 2011-11-25 19:28 vcsa crw-rw---- 1 root tty 7, 129 2011-11-25 19:28 vcsa1 crw-rw---- 1 root tty 7, 130 2011-11-25 19:28 vcsa2 crw-rw---- 1 root tty 7, 131 2011-11-25 19:28 vcsa3 crw-rw---- 1 root tty 7, 132 2011-11-25 19:28 vcsa4 crw-rw---- 1 root tty 7, 133 2011-11-25 19:28 vcsa5 crw-rw---- 1 root tty 7, 134 2011-11-25 19:28 vcsa6 crw------- 1 root root 10, 63 2011-11-25 19:28 vga_arbiter crw-rw----+ 1 root video 81, 0 2011-11-25 19:28 video0 crw-rw-rw- 1 root root 1, 5 2011-11-25 19:28 zero sg_scan -i gives me: sudo sg_scan -i /dev/sg0: scsi0 channel=0 id=0 lun=0 [em] ATA ST31000524NS SN12 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg1: scsi0 channel=0 id=1 lun=0 [em] ATA WDC WD15EADS-00S 01.0 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg2: scsi2 channel=0 id=0 lun=0 [em] HL-DT-ST BDDVDRW CH08LS10 2.00 [rmb=1 cmdq=0 pqual=0 pdev=0x5] sg_map gives me: /dev/sg0 /dev/sda /dev/sg1 /dev/sdb /dev/sg2 /dev/scd0 lsscsi -l gives me: [0:0:0:0] disk ATA ST31000524NS SN12 /dev/sda state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30 [0:0:1:0] disk ATA WDC WD15EADS-00S 01.0 /dev/sdb state=running queue_depth=1 scsi_level=6 type=0 device_blocked=0 timeout=30 [2:0:0:0] cd/dvd HL-DT-ST BDDVDRW CH08LS10 2.00 /dev/sr0 state=running queue_depth=1 scsi_level=6 type=5 device_blocked=0 timeout=30 my udf mod is: filename: /lib/modules/3.0.0-14-generic/kernel/fs/udf/udf.ko license: GPL description: Universal Disk Format Filesystem author: Ben Fennema srcversion: 6ABDE012374D96B9685B8E5 depends: crc-itu-t vermagic: 3.0.0-14-generic SMP mod_unload modversions Do I need special drivers or mods enabled? Do I need to change some BIOS settings? edit: Somehow I am now able to fire the mount command without any filesystem errors, but now I get: mount: no medium found on /dev/sr0

  Read the article

• Ubuntu 12.04 + Raid0 + Windows 7 not loading

  - by Douglas

  please someone help me.... (Sorry for my english) Hi, I have a Pc with 2 Hd (1Tb each) on Raid0. I had a Windows 7 64bits working for several months. When I installed the Windows I let a 100Gb partition empty to install Ubuntu someday. I was using Linux on a Virtualbox, but this week I tried to install Ubuntu 12.04 in this 100Gb partition. I used the Ubuntu alternate cd, because the 'normal' cd was giving me trouble with the Raid0. The grub installation always reported a error. After a lot of work I found that I nedded to install grub on partition /dev/mapper/isw_chjbfeec_DougRaid1 (see Bootinfo below). The Windows installation created a 100Mb boot partition, so I needed to install grub in this partition. Now I have the Ubuntu working 100% ok. The problem is, the Windows is not booting! The windows option is present on the grub menu, but when I choose the windows option there is a black screen and after that the grub is reloaded. My Bootinfo is: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for /boot/grub. => Grub2 (v1.99) is installed in the MBR of /dev/mapper/isw_chjbfeec_DougRaid and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for /boot/grub. sda1: __________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' sda2: __________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' mount: unknown filesystem type '' sda3: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: isw_chjbfeec_DougRaid1: ________________________________________________________ File system: ntfs Boot sector type: Grub2 (v1.99) Boot sector info: Grub2 (v1.99) is installed in the boot sector of isw_chjbfeec_DougRaid1 and looks at sector 3841862992 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. No errors found in the Boot Parameter Block. Operating System: Boot files: /grldr /bootmgr /Boot/BCD /grldr isw_chjbfeec_DougRaid2: ________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /Windows/System32/winload.exe isw_chjbfeec_DougRaid3: ________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: isw_chjbfeec_DougRaid5: ________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img isw_chjbfeec_DougRaid6: ________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/sda2 206,848 3,686,402,047 3,686,195,200 7 NTFS / exFAT / HPFS /dev/sda3 3,686,402,558 3,907,039,743 220,637,186 5 Extended Invalid MBR Signature found. EBR refers to a location outside the hard drive. /dev/sda2 ends after the last sector of /dev/sda /dev/sda3 ends after the last sector of /dev/sda Drive: isw_chjbfeec_DougRaid _____________________________________________________________________ Disk /dev/mapper/isw_chjbfeec_DougRaid: 2000.4 GB, 2000404348928 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907039744 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/mapper/isw_chjbfeec_DougRaid1 * 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/mapper/isw_chjbfeec_DougRaid2 206,848 3,686,402,047 3,686,195,200 7 NTFS / exFAT / HPFS /dev/mapper/isw_chjbfeec_DougRaid3 3,686,402,558 3,907,039,743 220,637,186 5 Extended /dev/mapper/isw_chjbfeec_DougRaid5 3,686,402,560 3,881,876,479 195,473,920 83 Linux /dev/mapper/isw_chjbfeec_DougRaid6 3,881,876,992 3,907,039,743 25,162,752 82 Linux swap / Solaris "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/mapper/isw_chjbfeec_DougRaid1 C89C73D19C73B910 ntfs Reservado pelo Sistema /dev/mapper/isw_chjbfeec_DougRaid2 6830883A3088116C ntfs /dev/mapper/isw_chjbfeec_DougRaid5 bbab868a-ea53-4be3-ba7d-2737fe6cb24c ext4 /dev/mapper/isw_chjbfeec_DougRaid6 7a830a3c-88fb-4cba-80dc-f32e08abfd5b swap /dev/sda isw_raid_member /dev/sdb isw_raid_member /dev/sr0 iso9660 Windows7x86x64SK ========================= "ls -R /dev/mapper/" output: ========================= /dev/mapper: control isw_chjbfeec_DougRaid isw_chjbfeec_DougRaid1 isw_chjbfeec_DougRaid2 isw_chjbfeec_DougRaid3 isw_chjbfeec_DougRaid5 isw_chjbfeec_DougRaid6 ================================ Mount points: ================================= Device Mount_Point Type Options /dev/mapper/isw_chjbfeec_DougRaid5 / ext4 (rw,errors=remount-ro) /dev/sr0 /media/Windows7x86x64SK iso9660 (ro,nosuid,nodev,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500,uhelper=udisks) ================= isw_chjbfeec_DougRaid1/grldr embedded menu: ================== -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- ================== isw_chjbfeec_DougRaid5/boot/grub/grub.cfg: ================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="$1" if [ "$1" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-24-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux /boot/vmlinuz-3.2.0-24-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-24-generic-pae } menuentry 'Ubuntu, with Linux 3.2.0-24-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c echo 'Loading Linux 3.2.0-24-generic-pae ...' linux /boot/vmlinuz-3.2.0-24-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-24-generic-pae } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 3.2.0-23-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux /boot/vmlinuz-3.2.0-23-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-23-generic-pae } menuentry 'Ubuntu, with Linux 3.2.0-23-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c echo 'Loading Linux 3.2.0-23-generic-pae ...' linux /boot/vmlinuz-3.2.0-23-generic-pae root=UUID=bbab868a-ea53-4be3-ba7d-2737fe6cb24c ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-23-generic-pae } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/mapper/isw_chjbfeec_DougRaid3,msdos1)' search --no-floppy --fs-uuid --set=root bbab868a-ea53-4be3-ba7d-2737fe6cb24c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober_proxy ### menuentry "Windows 7 (loader) (on /dev/mapper/isw_chjbfeec_DougRaid1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(sda,msdos1)' search --no-floppy --fs-uuid --set=root C89C73D19C73B910 chainloader +1 } ### END /etc/grub.d/30_os-prober_proxy ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- ====================== isw_chjbfeec_DougRaid5/etc/fstab: ======================= -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/isw_chjbfeec_DougRaid5 / ext4 errors=remount-ro 0 1 /dev/mapper/isw_chjbfeec_DougRaid6 none swap sw 0 0 -------------------------------------------------------------------------------- ========== isw_chjbfeec_DougRaid5: Location of files loaded by Grub: =========== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.2.0-23-generic-pae 2 = boot/initrd.img-3.2.0-24-generic-pae 2 = boot/vmlinuz-3.2.0-23-generic-pae 1 = boot/vmlinuz-3.2.0-24-generic-pae 1 = initrd.img 2 = initrd.img.old 2 = vmlinuz 1 = vmlinuz.old 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda1 Unknown BootLoader on sda2 Unknown BootLoader on sda3 =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt hexdump: /dev/sda1: No such file or directory hexdump: /dev/sda1: No such file or directory hexdump: /dev/sda2: No such file or directory hexdump: /dev/sda2: No such file or directory hexdump: /dev/sda3: No such file or directory hexdump: /dev/sda3: No such file or directory xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in How we can see the Windows part at grub is: menuentry "Windows 7 (loader) (on /dev/mapper/isw_chjbfeec_DougRaid1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(sda,msdos1)' search --no-floppy --fs-uuid --set=root C89C73D19C73B910 chainloader +1 } I tried a lot of combinations at the line: set root='(sda,msdos1)' , but no success I tried to change uuid to the /dev/mapper/isw_chjbfeec_DougRaid2 uuid, but the grub reports a error. I dont know what to do now. I really need to boot my windows partition. Someone knows what to do? Thanks........

  Read the article

• How do I prevent missing network from slowing down boot-up?

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Slow boot on Ubuntu 12.04, probable cause the network connection

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

< Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >