Search Results

Search found 2833 results on 114 pages for 'tom ryan'.

Page 39/114 | < Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >

• CPU clock scales down so computer is unusable after switching to battery

  - by Ryan

  When I am plugged in my laptop runs great however when I unplug it and I'm on battery power my CPU clock speed scales down pretty much all the way. I know this is happening by monitoring the clock speed. When plugged in it will usually stay between 1000MHz and 3000MHz but when I unplug it it quickly scales down to less than 500MHz and will get as low as 100MHz and it will NEVER scale up at all on battery power. After I plug the power back in it will then begin operating normally in about a minute. I have tried setting the MIN and MAX CPU performance in power options to 100% and have tried messing around with cooling settings which seemed to be a problem with HP laptops. I have a Toshiba Satellite M500-ST6444 running Windows 7. The BIOS is up to date. I have tried two versions.

  Read the article

• How can I make Excel correlate data from two data sets into a single graph?

  - by Tom Ritter

  I have two datasets, one being sparser than the other. They look like this: Data Set 1: 4 50 5 55 6 60 7 70 8 80 Data Set 2: 4 10 6 20 8 30 I have several hundred points instead of this few. I want them in the same graph, the X axis being 4-8, the y axis being 0-100ish, and two lines, one for each data set. What I get is two lines, not correlated at all along the X axis, and the X axis being labeled from one of the two datasets, with the labels being wrong for the other. The smaller data set is one-point-per-tick on the x axis, when I need it to skip ticks and actually line up with the other data set. Not married to excel, willing to try this in something else if it's free.

  Read the article

• IP-restricted port forwarding with iptables

  - by Tom

  For an example, I have two authorized client computers, 1.1.1.1 and 2.1.1.1. My server running iptables is 3.1.1.1 and my firewalled web server is 4.1.1.1. When one of the authorized client IPs connects to 3.1.1.1 on port 80, I would like the connection to be forwarded to 4.1.1.1 on port 8888. If any other IP attempts to connect I would like it to refuse/drop the connection. What iptables config would accomplish this? Is there something more specific out there that would be better suited for this job?

  Read the article

• Setup dual screen with Catalyst Control Center on notebook so that nothing changes when closing lid (case) ?

  - by Tom

  I have setup a dualscreen setup for my notebook with an ATI video card (ATI mobility radeon hd 5470) using Catalyst Control Center. The monitor extends the desktop of the notebook's screen. This works great. I am running on windows 7 and have set it up to not do anything when I close my laptop's lid (case) other than dim the notebook's display. However, when I do close the lid (notebook's display), the second monitor suddenly changes and I believe it starts behaving as the primary monitor.. I do not want this to happen. So, how do I setup my dualscreen setup so that it won't set the secondary monitor as the primary one when I close my laptop's lid? UPDATE: this video shows exactly what my problem is: http://www.youtube.com/watch?v=Q1ygNHbqI2g

  Read the article

• What are the Windows G: through Z: drives used for?

  - by Tom Wijsman

  In Windows you have a C: drive. The first things labeled beyond that seems to be extra stuff. So my DVD drive is D: and if you put in a USB stick it becomes F:. And then some people also have A: and B:. But then, what and where are G: through Z: drives for? Is it possible to connect so many things to a computer to make them all in use? Or more than them? Would it give a BSOD? Or would this slow down the system somehow? Or what would happen? What if I want to connect even more drives to the computer? Because with the hard drive limits it's more efficient to buy more drives than to buy a single drive with a lot of capacity. Is it possible to create drive letters like 0: through Z: or AA: through ZZ:?

  Read the article

• Renaming Nginx 1.3.5 Server: response header

  - by Ryan

  In nginx 1.2 & 1.3 you can modify the source to change the name: src/http/ngx_http_header_filter_module.c (lines 48 and 49): static char ngx_http_server_string[] = "Server: Not Nginx" CRLF; static char ngx_http_server_full_string[] = "Server: Not Nginx/1.0" CRLF; Renaming those and recompiling the source changes the server response name in nginx 1.2. However doing this in 1.3 does not seem to change the name. It still says nginx/1.3.5 and with server_tokens off; it just says nginx. How can I change the server name in 1.3 without installing the 3rd party addon headers more? I want to compile from source.

  Read the article

• add blank for 0 result into existing formula

  - by Tom

  is there any way to use this formula [<30,0,1)) for a group of cells in Sheet1!(A14:I100)] and if result == 0 insert blank or add [=IF(O16=0,"",] somehow so all 0 results just show a blank result. I'm just not sure how to add this to my formula so if Cell a176= 07:48:16 and formula [<30,0,1)) for a group of cells in Sheet1!(A14:I100)] changes it to 468, all is good - however if Cell a176= 00:00:16, the result is "0" - I would like the result to be "" blank "" instead of "0". any ideas??

  Read the article

• Ubuntu 12.04 3.2 Kernel showing incorrect "cache size" in cpuinfo?

  - by Tom G

  2x Xeon E5620 . 16 Cores altogether. /proc/cpuinfo shows cache is only @ 4096kb According to intel this should have 12MB of "smart cache". Doing searched for E5620 and CPUinfo shows the correct number: cache size : 12288 KB However mine shows this: processor : 15 v endor_id : GenuineIntel cpu family : 6 model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz stepping : 2 microcode : 0x1 cpu MHz : 2400.104 cache size : 4096 KB fpu : yes fpu_exception : yes cpuid level : 11 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush mmx bogomips : 4800.20 clflush size : 64 cache_alignment : 64 address sizes : 40 bits physical, 48 bits virtual Any idea on why it shows like it's missing 8MB in CPU cache? .

  Read the article

• growing EBS RAID volume

  - by Ryan Fernandes

  I've created a RAID0 configuration with two 1GB EBS volumes, mounted at /dev/md0 using mdadm and formatted with XFS Next, I copied some files over to fill the volume to around 30% of its capacity (of 2GB) I then created snapshots of the volumes using ec2-consistent-snapshot and created volumes of the said snapshots but specified the volume size to be 2GB (effective doubling the capacity on each disk) I then spun up a new instance, assembled the RAID0 configuration on /dev/md0 from the 2 volumes mentioned above and mount it to /vol df -hT showed /vol as 2GB (as expected) Now I ran sudo xfs_growfs -d /vol. The command completed normally but reported blocks changed from 523776 to 524160 (only!) and df -hT still showed /vol as 2GB (instead of the expected 4GB) I rebooted, remounted, reassembled the RAID but it still reports the old size. EDIT: trying to grow the RAID using mdadm --grow yields mdadm: raid0 array /dev/md0 cannot be reshaped Is there any other way I can grow a RAID0 array?

  Read the article

• Does Intel Smart Response provide any statistics on the cache usage?

  - by Tom Seddon

  I've set up my Z68-based Core i7 PC with a 60GB SSD dedicated as a Smart Response cache drive. Is there any way I can get any statistics out of it? It would be nice to have some information on how much cache space is actually being used, maybe how much of it was actually accessed recently, and how many reads in general are coming from the SSD rather than from the mechanical disk. These statistics might help to quickly provide some evidence for or against the use of Smart Response, without my having to reinstall Windows on the SSD (etc.) to find out. The Windows ReadyBoost feature has some performance counters you can access via the Windows 7 perfmon tool, for example, which is the kind of thing I'm hoping is somehow available. Smart Response provides no perfmon counters, though, and the Intel Rapid Storage Utility tells you pretty much nothing except that Smart Response is switched on.

  Read the article

• Can I use a micro ec2 instance as a load balancer for my other large ec2 instances?

  - by Ryan Detzel

  The issue I'm having is I want to upgrade that instance often(security patches, etc) but I'm affriad something will fail and the site will be down. So, I want to have another server setup and load balance between the two that way I can easily disable one, upgrade it and once it's working add it back in the mix and repeat. What kind of machine is needed for a load balancer? Would the micro instance work just fine? The site gets anywhere from 3-10k hits/day. I plan on using nginx as the load balancer.

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• Windows 8 not booting from DVD while trying to install in a Ubuntu 14.04 system

  - by Tom

  Currently my system runs on Ubuntu 14.04. Yesterday, I deleted and formatted the partition(C drive) as NTFS in which Windows 7 was installed because Windows 7 was not booting for more than a week. I have a Windows 8 disk and it was able to boot from that disk when there was Windows 7 on my system. After the formatting of C drive yesterday, I tried to install Windows 8 by booting from the disk. Unfortunately, this time no booting happened from the disk. So I pressed F2 during the system start up and checked Boot Device Priority, Optical Drive has the first priority there. So why Windows 8 didn't boot from the disk ? I need to install Windows 8 too in my system without doing any damage to Ubuntu 14.04. How can I do it ?

  Read the article

• Firewall still blocking port 53 despite listing otherwise?

  - by Tom

  I have 3 nodes with virtually the same iptables rules loaded from a bash script, but one particular node is blocking traffic on port 53 despite listing it's accepting it: $ iptables --list -v Chain INPUT (policy DROP 8886 packets, 657K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo any anywhere anywhere 2 122 ACCEPT icmp -- any any anywhere anywhere icmp echo-request 20738 5600K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- eth1 any anywhere node1.com multiport dports http,smtp 0 0 ACCEPT udp -- eth1 any anywhere ns.node1.com udp dpt:domain 0 0 ACCEPT tcp -- eth1 any anywhere ns.node1.com tcp dpt:domain 0 0 ACCEPT all -- eth0 any node2.backend anywhere 21 1260 ACCEPT all -- eth0 any node3.backend anywhere 0 0 ACCEPT all -- eth0 any node4.backend anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 15804 packets, 26M bytes) pkts bytes target prot opt in out source destination nmap -sV -p 53 ns.node1.com // From remote server Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2011-02-24 11:44 EST Interesting ports on ns.node1.com (1.2.3.4): PORT STATE SERVICE VERSION 53/tcp filtered domain Nmap finished: 1 IP address (1 host up) scanned in 0.336 seconds Any ideas? Thanks

  Read the article

• Why are some UDP packets getting blocked?

  - by Tom

  In our organization, we have two test machines running Windows XP. While attempting to test a roll-my-own UDP message server, I found that both could receive small messages (under 2k) just fine. However, when I test sending large packets to both of these machines, one receives them fine, while the other can't receive them at all. Both machines have SP3 and both have their Windows Firewall shut off, but one still isn't working. Can anyone tell me where to look for anything that might be blocking or limiting the packet size on a Windows Machine? Thanks.

  Read the article

• Service or software to auto-sync one server to another so they are identical?

  - by Ryan

  We have a main node in a DC data center and want to setup a back-up node in Seattle. The back-up node will only be used if the DC node goes down and we switch it over while DC node is repaired. The question is, what kind of services out there allow me to sync the data, I suppose we want to do it fairly frequently so if something goes down there isn't much loss in data between the time of failure and the last back-up/sync. Is there any common solution for this? It's Windows Server 2003 running Parallels Virtuozzo.

  Read the article

• "Countersigning" a CA with openssl

  - by Tom O'Connor

  I'm pretty used to creating the PKI used for x509 authentication for whatever reason, SSL Client Verification being the main reason for doing it. I've just started to dabble with OpenVPN (Which I suppose is doing the same things as Apache would do with the Certificate Authority (CA) certificate) We've got a whole bunch of subdomains, and applicances which currently all present their own self-signed certificates. We're tired of having to accept exceptions in Chrome, and we think it must look pretty rough for our clients having our address bar come up red. For that, I'm comfortable to buy a SSL Wildcard CN=*.mycompany.com. That's no problem. What I don't seem to be able to find out is: Can we have our Internal CA root signed as a child of our wildcard certificate, so that installing that cert into guest devices/browsers/whatever doesn't present anything about an untrusted root? Also, on a bit of a side point, why does the addition of a wildcard double the cost of certificate purchase?

  Read the article

• I just deleted "/bin". What's the best way to recover?

  - by Tom Marthenal

  I just ran (not on purpose!) rm -rf /bin. I've booted down the computer and am using Finnix to try to recover from it. I have succeeded in mounting the drive, and confirmed that, yes, the entire /bin folder is deleted. Is it possible to recover from this without reinstalling the OS? I'm thinking that I could setup a VM with the same OS and architecture (Ubuntu Server 11.10 alpha release, x86) and install all the packages I had installed on the server, then just copy the /bin folder. Will this work? Am I better off just starting over?

  Read the article

• rdp allow client reconnect without password prompt after several hours

  - by Tom

  Let me describe the setup first: client PC with several rdp sessions to local servers, all opened from saved rdp sessions with stored passwords, using the standard windows rdp client. several windows servers on the LAN, with varying server OS: windows server 2003, 2008, and even 2012 now. When I log onto my PC I open up rdp sessions to all those servers, and keep them open all the time for various reasons. Overnight the client PC is put into sleep or hibernate mode, thereby braking the rdp connections. On the next day when I wake the client PC and login again, the rdp sessions automatically try to reconnect to the servers, and this leads to the question: starting with server 2008 something apparently changed in the rdp server config, as all servers with 2008, 2008r2 and 2012 will prompt for the password in the rdp session, whereas the 2003 server rdp connections will re-establish without the password prompt. Apparently there is a timeout setting on 2008+ that, when exceeded, requires a reauthentication. Is there any way to setup the 2008+ servers to behave like 2003 did? I'd like the rdp sessions to reconnect without a password prompt even after a several hour disconnect.

  Read the article

• Force request to miss cache but still store the response

  - by Tom Marthenal

  I have a slow web app that I've placed Varnish in front of. All of the pages are static (they don't vary for a different user), but they need to be updated every 5 minutes so they contain recent data. I have a simple script (wget --mirror) that crawls the entire website every 15 minutes. Each crawl takes about 5 minutes. The point of the crawl is to update every page in the Varnish cache so that a user never has to wait for the page to generate (since all pages have been generated recently thanks to the spider). The timeline looks like this: 00:00:00: Cache flushed 00:00:00: Spider starts crawling to update cache with new pages 00:05:00: Spider finishes crawling, all pages are updated until 1:15 A request that comes in between 0:00:00 and 0:05:00 might hit a page that hasn't been updated yet, and will be forced to wait a few seconds for a response. This isn't acceptable. What I'd like to do is, perhaps using some VCL magic, always foward requests from the spider to the backend, but still store the response in the cache. This way, a user will never have to wait for a page to generate since there is no 5-minute window in which parts of the cache are empty (except perhaps at server startup). How can I do this?

  Read the article

• Our company claims that the DLP system can even monitor the contents of HTTPS traffic, how is this possible?

  - by Ryan

  There is software installed on all client machines for DLP (Data Loss Prevention) and HIPAA compliance. Supposedly it can read HTTPS data clearly. I always thought that between the browser and the server, this was encrypted entirely. How can software sneak in and grab this data from the browser prior to it is encrypted or after it is decrypted? I am just curious as to how this could be possible. I would think that a browser wouldn't be considered very secure if this was possible.

  Read the article

• Adding file to /etc/cron.d doesn't make it run (ubuntu 10.04)

  - by tom

  If I scp a cron file into /etc/cron.d it doesn't run unless I edit the file and change the command. Then crond seems to pick up the cron file. How can I make cron reload its cron files in ubuntu 10.04? 'touch'ing the file doesn't work nor does 'restart cron' or 'reload cron'. My cron file is set to run every minute and logs to a file. Nothing ends up in the log file until I edit the command, and there's no entry for it in /var/log/syslog I'm stumped. Here's my cron file saved to /etc/cron.d/runscript # Runs the script every minute. This is safe because it will exit with success if it's already running * * * * * www-data if [ -f /usr/local/bin/thing ]; then exec /usr/bin/php /usr/local/bin/thing mode:prod -a 14 -d >> /var/log/thing/mything.log 2>&1; else echo `date +'[%D %T]'` "Thing not deployed. Command not run\n" >> /var/log/thing/mything.log; fi &

  Read the article

• Connecting to SVN server from a computer outside of my LAN

  - by Tom Auger

  I've got a Fedora server running Subversion and svnserve on port 3690. My repo is at /var/svn/project_name. I have my router forwarding port 3690 to the local server (as well as port 80, 21, 22 and a few others). When I connect locally to svn://192.168.0.2/project_name it works great. When I connect from an external server to svn://my.static.ip/project_name I get a time out connecting to the host. However, if I http://my.static.ip there is no problem, so port forwarding is working (at least for port 80). I don't want to run WebDAV or svn via HTTP/s. I'd like it to work using svnserve, as documented in the svn book. What have I misconfigured? EDIT Here is the last part of my iptables dump. I'm not an expert, but it looks OK to me: ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:svn ACCEPT udp -- anywhere anywhere state NEW udp dpt:svn ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:6680:6699 ACCEPT udp -- anywhere anywhere state NEW udp dpts:6680:6699 REJECT all -- anywhere anywhere reject-with icmp-host-prohibited EDIT 2 Results from sudo netstat -tulpn tcp 0 0 0.0.0.0:3690 0.0.0.0:* LISTEN 1455/svnserve

  Read the article

• Relayout LVM Disk

  - by Tom

  I have an Ubuntu 11.10 system with two 500GB disks. The partition tables look like this: /dev/sda1 primary 465.52GB /dev/sda2 extended 243.17MB -> /dev/sda5 logical 243.14MB /dev/sdb1 primary 465.76GB sda1 and sdb1 are in a single LVM physical volume group containing a single logical volume containing a single logical filesystem which is mounted as /. sda5 is mounted as /boot. The problem comes when I want to upgrade to Ubuntu 12.04, which requires at least 247MB free on /boot. So I need to reduce the size of sda1 so that I can increase the size of sda2 and sda5. How the heck do I do that? I can find how to shrink the logical volume group, but I'm not at all clear on how to clear out the end part of sda1 so that I can reduce the physical volume group. Does pvresize just deal with this automagically? Or is that wild wishful thinking? I guess the alternatives are to back everything up onto something or other and recreate the thing from scratch or find out whether GRUB2 supports using LVM for /boot.

  Read the article

• Explorer.exe - No such interface supported and other issues

  - by tom

  The problem started when I uninstalled my ATI graphics driver and i used a driver cleaner. After i restarted win7 and it got to POST the screen just went completely blank. So i Used system restore from the repair menu to get back on. I found out that if I ran chkdsk the display just goes black after restart on startup and i have to use system restore to get back on windows7 not sure why this is. When i right click desktop and choose 'Screen Resolution' it says No such interface supported. Also when I click items such as device manager in the windows explorer it does not do anything. I have tried re-registering the DLLS but that did not do anything.

  Read the article

< Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46  | Next Page >