Search Results

Search found 68949 results on 2758 pages for 'diamond problem'.

Page 390/2758 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

• How do I make changes to /proc/acpi/wakeup permanent?

  - by Jolan

  I had a problem with my Ubuntu 12.04 waking up immediately after going into suspend. I solved the problem by changing the settings in /proc/acpi/wakeup, as suggested in this question: How do I prevent immediate wake up from suspend?. After changing the settings, the system goes flawlessly into suspend and stays suspended, but after I wake it back up, the settings in /proc/acpi/wakeup are different from what I set them to. Before going to suspend: cat /proc/acpi/wakeup Device S-state Status Sysfs node SMB0 S4 *disabled pci:0000:00:03.2 PBB0 S4 *disabled pci:0000:00:09.0 HDAC S4 *disabled pci:0000:00:08.0 XVR0 S4 *disabled pci:0000:00:0c.0 XVR1 S4 *disabled P0P5 S4 *disabled P0P6 S4 *disabled pci:0000:00:15.0 GLAN S4 *enabled pci:0000:03:00.0 P0P7 S4 *disabled pci:0000:00:16.0 P0P8 S4 *disabled P0P9 S4 *disabled USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *disabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *disabled pci:0000:00:06.1 PWRB S4 *enabled SLPB S4 *enabled I tell the system to suspend, and it works as it should. But later after waking it up, the settings are changed to either: USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 or USB0 S3 *enabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *enabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 Any ideas? Thank you for your response. Unfortunately it did not solve my problem. all of /sys/bus/usb/devices/usb1/power/wakeup /sys/bus/usb/devices/usb2/power/wakeup /sys/bus/usb/devices/usb3/power/wakeup /sys/bus/usb/devices/usb4/power/wakeup as well as /sys/bus/usb/devices/3-1/power/wakeup are set to disabled, and the notebook still wakes up by itself right after going to sleep. The only thing it seems to react to are the settings in /proc/acpi/wakeup, which keep changing (resetting) every time i power off/restart my notebook.

  Read the article

• Is my sequence diagram correct?

  - by Dummy Derp

  NOTE: I am self studying UML so I have nobody to verify my diagrams and hence I am posting here, so please bear with me. This is the problem I got from some PDF available on Google that simply had the following problem statement: Problem Statement: A library contains books and journals. The task is to develop a computer system for borrowing books. In order to borrow a book the borrower must be a member of the library. There is a limit on the number of books that can be borrowed by each member of the library. The library may have several copies of a given book. It is possible to reserve a book. Some books are for short term loans only. Other books may be borrowed for 3 weeks. Users can extend the loans. Draw a use case diagram for a library. I already drew the Use Case diagram and had it checked by a community member. This time I drew sequence diagrams for borrowing a book and extending the date of return. Please let me know if they are correct. I drew them using Visual Paradigm and I dont know how to keep a control of the sequence numbers. If you do, please let me know :) Diagrams

  Read the article

• Apache VERY high page load time

  - by Aaron Waller

  My Drupal 6 site has been running smoothly for years but recently has experienced intermittent periods of extreme slowness (10-60 sec page loads). Several hours of slowness followed by hours of normal (4-6 sec) page loads. The page always loads with no error, just sometimes takes forever. My setup: Windows Server 2003 Apache/2.2.15 (Win32) Jrun/4.0 PHP 5 MySql 5.1 Drupal 6 Cold fusion 9 Vmware virtual environment DMZ behind a corporate firewall Traffic: 1-3 hits/sec avg Troubleshooting No applicable errors in apache error log No errors in drupal event log Drupal devel module shows 242 queries in 366.23 milliseconds,page execution time 2069.62 ms. (So it looks like queries and php scripts are not the problem) NO unusually high CPU, memory, or disk IO Cold fusion apps, and other static pages outside of drupal also load slow webpagetest.org test shows very high time-to-first-byte The problem seems to be with Apache responding to requests, but previously I've only seen this behavior under 100% cpu load. Judging solely by resource monitoring, it looks as though very little is going on. Here is the kicker - roughly half of the site's access comes from our LAN, but if I disable the firewall rule and block access from outside of our network, internal (LAN) access (1000+ devices) is speedy. But as soon as outside access is restored the site is crippled. Apache config? Crawlers/bots? Attackers? I'm at the end of my rope, where should I be looking to determine where the problem lies?

  Read the article

• IE won't load PDF in a window created with window.open

  - by Dean

  Here's the problem, which only occurs in Internet Explorer (IE). I have a page that has links to several different types of files. Links from these files execute a Javascript function that opens a new window and loads the specific file. This works great, unless the file I need to open in the new window is a PDF in which case the window is blank, even though the URL is in the address field. Refreshing that window using F5 doesn't help. However, if I put the cursor in the address field and press <enter> the PDF loads right up. This problem only occurs in IE. I have seen it in IE 7 and 8 and am using Adobe Acrobat Reader 9. In Firefox (PC and Mac) everything works perfectly. In Chrome (Mac), the PDF is downloaded. In Safari (Mac) it works. In Opera (Mac) it prompts me to open or save. Basically, everything probably works fine, except for IE. I have searched for similar problems and have seen some posts where it was suggested to adjust some of the Internet Options on IE. I have tried this but it doesn't help, and the problem wasn't exactly the same anyway. Here's the Javascript function I use to open the new window. function newwin(url,w,h) { win = window.open(url,"temp","width="+w+",height="+h+",menubar=yes,toolbar=yes,location=yes,status=yes,scrollbars=auto,resizable=yes"); win.focus(); } You can see that I pass in the URL as well as the height, h, and width, w, of the window. I've used a function like this for years and as far as I know have never had a problem. I call the newwin() function using this. <a href="javascript:newwin('/path/document.pdf',400,300)">document.pdf</a> (Yes, I know there are other, better ways than using inline JS, and I've even tried some of them because I've run out of things to try, but nothing works.) So, if anyone has an idea as to what might be causing this problem, I'd love to hear it.

  Read the article

• Use depth bias for shadows in deferred shading

  - by cubrman

  We are building a deferred shading engine and we have a problem with shadows. To add shadows we use two maps: the first one stores the depth of the scene captured by the player's camera and the second one stores the depth of the scene captured by the light's camera. We then ran a shader that analyzes the two maps and outputs the third one with the ready shadow areas for the current frame. The problem we face is a classic one: Self-Shadowing: A standard way to solve this is to use the slope-scale depth bias and depth offsets, however as we are doing things in a deferred way we cannot employ this algorithm. Any attempts to set depth bias when capturing light's view depth produced no or unsatisfying results. So here is my question: MSDN article has a convoluted explanation of the slope-scale: bias = (m × SlopeScaleDepthBias) + DepthBias Where m is the maximum depth slope of the triangle being rendered, defined as: m = max( abs(delta z / delta x), abs(delta z / delta y) ) Could you explain how I can implement this algorithm manually in a shader? Maybe there are better ways to fix this problem for deferred shadows?

  Read the article

• What browser is sending user agent beginning mozilla/5.0+, tramslates & into &amp;

  - by Patrick

  We've got a website which has been running for a few years now. One of our customers has just started having an intermittent problem. Looking at our iis6.0 logs the service works correctly when they have a user agent beginning "mozilla/4.0+" but fails when the user agent begins "mozilla/5.0+". The particular customer only started having this problem on Wednesday. Does anyone know the browser/upgrade which changes the 4.0 to 5.0? The actual problem caused is that an "&" in a url parameter list is being encoded as "&amp;". Anyone seen anything similar? We have other users sending from browsers with the 5.0+ user agent without trouble. Sorry about the tags but don't have the rep to create new ones. Thanks in advance, Patrick Edit: hi Viper_sb, It is most probably a custom script (I'm primarily a c++ developer so don't really understand). Our site services requests from other customer developed sites, this one was done in Java script as far as I know. we're actually getting a variety of user agents (presumably depending on which of our customers customers is accessing the service), here's a few: Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+fr;+rv:1.9.1.11)+Gecko/20100701+Firefox/3.5.11 Mozilla/5.0+(Windows;+U;+Windows+NT+5.1;+en-US)+AppleWebKit/533.4+(KHTML,+like+Gecko)+Chrome/5.0.375.126+Safari/533.4 302 0 0 Mozilla/5.0+(Macintosh;+U;+PPC+Mac+OS+X;+fr)+AppleWebKit/523.12+(KHTML,+like+Gecko)+Version/3.0.4+Safari/523.12 Mozilla/5.0+(Windows;+U;+Windows+NT+5.1;+en-US;+rv:1.9.2.8)+Gecko/20100722+Firefox/3.6.8 Mozilla/5.0+(Windows;+U;+Windows+NT+5.1;+fr;+rv:1.9.2.8)+Gecko/20100722+Firefox/3.6.8+(.NET+CLR+3.5.30729)

  Read the article

• SQL server timeout 2000 from C# .NET

  - by Johnny Egeland

  I have run into a strange problem using SQL Server 2000 and two linked server. For two years now our solution has run without a hitch, but suddenly yesterday a query synchronizing data from one of the databases to the other started timing out. I connect to a server in the production network, which is linked to a server containing orders I need data from. The query contains a few joins, but basically this summarizes what is done: INSERT INTO ProductionDataCache (column1, column2, ...) SELECT tab1.column1, tab1.column2, tab2.column1, tab3.column1 ... FROM linkedserver.database.dbo.Table1 AS tab1 JOIN linkedserver.database.dbo.Table2 AS tab2 ON (...) JOIN linkedserver.database.dbo.Tabl32 AS tab3 ON (...) ... WHERE tab1.productionOrderId = @id ORDER BY ... Obviously my first attempt to fix the problem was to increase the timeout limit from the original 5 minutes. But when I arrived at 30 minutes and still got a timeout, I started to suspect something else was going on. A query just does not go from executing in less than 5 minutes to over 30 minutes over night. I outputted the SQL query (which was originally in the C# code) to my logs, and decided to execute the query in the Query Analyzer directly on the database server. To my big surprise, the query executed correctly in less than 10 seconds. So I isolated the SQL execution in a simple test program, and observed the same query time out both on the server originally running this solution AND when running it locally on the database server. Also I have tried to create a Stored Procedure and execute this from the program, but this also times out. Running it in Query Analyzer works fine in less than a few seconds. It seems that the problem only occurs when I execute this query from the C# program. Has anyone seen such behavior before, and found a solution for it? UPDATE: I have now used SQL Profiler on the server. The obvious difference is that when executing the query from the .NET program, it shows up in the log as "exec sp_executesql N'INSERT INTO ...'", but when executing from Query Analyzer it occurs as a normal query in the log. Further I tried to connect the SQL Query Analyzer using the same SQL user as the program, and this triggered the problem in Query Analyzer as well. So it seems the problem only occurs when connecting via TCP/IP using a sql user.

  Read the article

• Turning on the wireless card freezes Ubuntu 12.04

  - by Ryan Schram

  I've been using Ubuntu 12.04 for close to a year. Occasionally after booting into Gnome 3, the desktop is unresponsive to cursor clicks. The mouse cursor moves but can't open menus. Also the network icon displays a red error badge instead of the usual gray x indicating that it is off. The only way I have found to solve this is to switch to a terminal shell (Ctrl-Alt-F5), login and kill gnome-session. This is an intermittent and occasional problem. Recently I moved house and set up this computer in my new apartment. Now I have for the first time a new and more difficult problem. Switching on the wireless card (wlan0) to connect to the wifi router causes the desktop to freeze. Switching to a terminal via Ctrl-Alt-F5 doesn't work. The only solution is a hard reboot from the power switch. How can I diagnose the second, more recent problem? Is there a solution? Cheers, Ryan

  Read the article

• Am I correctly handling duplicate URLs for my homepage?

  - by Rob Goldstein

  I own a Job Search site named www.conservationjobboard.com and have a concern about how the domain is viewed by search engines. The issue is that when the site was first designed, the default page was left as default.php, but the homepage was actually JobBoard.php. To handle this, the default.php page performed a redirect to the JobBoard.php file when www.conservationjobboard.com/ was requested. The main problem resulted because the redirect was a temporary redirect causing search engines to index conservationjobboard.com/ and conservationjobboard.com/JobBoard.php as 2 separate pages. This has since been corrected to use the .htaccess file so that JobBoard.php is now the default file for the root directory eliminating the need for the redirect. Problem is that search engines still show both URL's in search results (one including JobBoard.php and one that ends with /). Another potential problem is that some of my early backlinks are to conservationjobboard.com/JobBoard.php while the rest are to conservationjobboard.com The 2 outstanding questions are as follows: 1. Is my domain still being penalized by search engines like Google for having duplicate homepage URL's? 2. Are all of the back links to my homepage being considered as the same now or is the total number of back links being split between the 2 different URL's? If you think there are still issues with how we have this set-up, I was wondering if you could give me advice on what we should do differently. Thanks.

  Read the article

• Out of space despite lots of free space remaining

  - by Kristian Thomsen

  When upgrading Ubuntu from 11.10 to 12.04 I discovered an unexpected problem. The upgrade was stopped because there wasn't enough free space for the installation. I managed to free some space and do the upgrade but now a prompt appears after logging in saying I'm out of space. This prompt asks me if I want to examine the problem. The "Disk Usage Analyser" is opened. In the top it says: Total filesystem capacity: 47.0 GB (used: 13.5 GB available: 33.4 GB) Folder -- Usage -- Size / -- 100% -- 12.5 GB usr -- 44.8 % -- 5.6 GB home -- 30.3 % -- 3.8 GB lib -- 13.0 % -- 1.6 GB var -- 9.1 % -- 1.1 GB boot 2.5 % 309.5 GB and a lot of small contributors like: etc, opt, sbin, bin etc. I do not really understand this problem since the analyser in the top says that I have 33.4 GB left in this file system. What can I do to make Ubuntu use the remaining space? Running df -i in the terminal gives: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda7 610800 576874 33926 95% / udev 213451 563 212888 1% /dev tmpfs 218524 486 218038 1% /run none 218524 3 218521 1% /run/lock none 218524 7 218517 1% /run/shm /dev/sda8 2264752 16371 2248381 1% /home What does this mean?

  Read the article

• How to deal with a 'public' work environment?

  - by Craige

  In the last 6 months, I have changed desks at my office 4 times. I don't mind, as it's due to expansion of the company and acquiring new office space and getting everybody settled. However, I truly miss the semi-private office I sat in 2 desks ago. I am now sitting in a large room with a number of other people. My problem with this isn't with my co-workers; everybody here is great. My problem is that based on the configuration of the room, no matter which desk I sit in, my monitors WILL be facing an open window. This causes a glare on my monitors, and it drives me crazy. I prefer a dark IDE theme as I find it easier on the eyes, however this just makes the glare that much worse. How should programmers cope with public office settings? Secondly, how should I cope with my specific problem? Should I give in and adopt a light IDE theme that will reduce the visibility of the glare but increase eye strain, or should I stick to my guns and find another solution?

  Read the article

• High load (and high temp) with idle processes

  - by Nanne

  I've got a semi-old laptop (toshiba satellite a110-228), that's appointed 'laptop for the kids' by my sister. I've installed ubuntu netbook (10.10) on it because of the lack-of memory and it seems to work fine, accept from some heat-issues. These where never a problem under windows. It looks like I've got something similar to this problem: Load is generally 1 or higher, sometimes its stuck at 0.80, but its way to high. Top/htop only show a couple of percentage CPU use (which isn't too shocking, as i'm not doing anything). At this point all the software is stock, and i'd like to keep it that way because its supposed to be the easy-to-maintain kids computer. Now I'd like to find out: What could be the cause of the high load? Could it be as this thread implies, some driver, are there other options to check? How could I see what is really keeping the system hot and bothered? How to check what runs, etc etc? I'd like to pinpoint the culprint. further steps to take for debugging? The big bad internet leads me to believe that it might be the graphics drivers. The laptop has an Intel 945M chipset, but that doesn't seem to be one of the problem childs in this manner (I read a lot abotu ATI drivers that need special isntall). I'd not only welcome hints to directly solve this (duh) but also help in starting to debug what is going on. I am really hesitant in installing an older kernel, as I want it to be stock, and easy upgradeable (because I don't live near it, it should run without me ;) ) As an afterthought: to keep the whole thing cooler, can I 'amp up' the fancontrol? Its only going "airplane" mode when the computer is 95 Celcius, which is a tad late for my taste. Top: powertop:

  Read the article

• Interpolate air drag for my game?

  - by Valentin Krummenacher

  So I have a little game which works with small steps, however those steps vary in time, so for example I sometimes have 10 Steps/second and then I have 20 Steps/second. This changes automatically depending on how many steps the user's computer can take. To avoid inaccurate positioning of the game's player object I use y=v0*dt+g*dt^2/2 to determine my objects y-position, where dt is the time since the last step, v0 is the velocity of my object in the beginning of my step and g is the gravity. To calculate the velocity in the end of a step I use v=v0+g*dt what also gives me correct results, independent of whether I use 2 steps with a dt of for example 20ms or one step with a dt of 40ms. Now I would like to introduce air drag. For simplicity's sake I use a=k*v^2 where a is the air drag's acceleration (I am aware that it would usually result in a force, but since I assume 1kg for my object's mass the force is the same as the resulting acceleration), k is a constant (in this case I'm using 0.001) and v is the speed. Now in an infinitely small time interval a is k multiplied by the velocity in this small time interval powered by 2. The problem is that v in the next time interval would depend on the drag of the last which again depends on the v of the last interval and so on... In other words: If I use a=k*v^2 I get different results for my position/velocity when I use 2 steps of 20ms than when I use one step of 40ms. I used to have this problem for my position too, but adding +g*dt^2/2 to the formula for my position fixed the problem since it takes into account that the position depends on the velocity which changes slightly in every infinitely small time interval. Does something like that exist for air drag too? And no, I dont mean anything like Adding air drag to a golf ball trajectory equation or similar, for that kind of method only gives correct results when all my steps are the same. (I hope you can understand my intermediate english, it's not my main language so I would like to say sorry for all the silly mistakes I might have made in my question)

  Read the article

• Nothing happens when I connect my Iphone 3G to my laptop

  - by Allwar

  Hi, how do i connect my iphone to my laptop (ubuntu 10.04) so that i can sync music and be able to look at it as a usb stick? (this is what I want to do but there is a problem.) When i connect it to my laptop nothing happens, it doesn't show up as an ikon or as a mass storage device. My Iphone runs 4.2.1 it's an Iphone 3G and it's not jailbroken for the moment, is that a problem? My laptop is an Asus 1201n ubuntu 10.04 (64-bits) Bus 002 Device 005: ID 05ac:1292 Apple, Inc. iPhone 3G I connected my Ipod Video (30 gb) and that one doesn't appear as well So I'm kind of stuck now. The problem probably lies in the system, because the usb port is working. Bus 002 Device 006: ID 05ac:1209 Apple, Inc. iPod Video I have added this PPA, I have done all of the sudo update and upgrade. but my computer doesn't realize that my Iphone is connected, whish isn't related to libimobiledevice. The port is working fine, it's my computer it doesn't recognize that I have my Iphone plugged-in! and the phone is working (tested it on my mac). I have the latest versions of these programs: hipo, ipod, gtkpod, ifuse, libusmuxd1 and usbmxd. I try to mount my iphone with fuse but i got this error. ( I connected my iPhone in windows 7 and it worked annoyingly.) alvar@alvars-laptop:~$ ifuse /mnt/iphone/ ERROR: the mount point specified does not exist

  Read the article

• ubuntu one syncronizing problems

  - by user72249

  I am a user of Ubuntu and Ubuntu One. First: I had a serious problem with ubuntu one. I have a windows and several Ubuntu machine and they all sync one account. My first problem is that i can't really delete files. Whenever I delete something Ubu One resync it, so it appears again in my folder. Furthermore, when i move something to another dir it synconize the new location and resync the old one, so i got doubled my files. I can't reorganize my files. So i tried to delete the duplicated files through the web dash, but i cant reorder and select multiple files by extension. For example i wanted to move all PDF to another location... Second: I can't configure in the ubuntu one app the loacation of the main One folder. For example i want my One folder to be on another partition than my HOME folder. It is a main problem in linux and windows also. I tried to move that folder in windows with the hardlink method. So i uninstalled the U1, then i created a folder link to another drive, than installed the U1. THEN i lost all my files in my U1. Lucky thing that i have a backup, but i thought U1 is a stable solution for me, and i planned to extend my space, but these bugs are major problems! It's worth to pay for it if it's working perfectly. I think it's more important than releasing a new version in every month.

  Read the article

• Grub doesn't show both Ubuntu installations

  - by jackweirdy

  I have a laptop with Ubuntu 12.04 LTS installed as the main OS. The other day I installed Ubuntu-Studio (version 12.04) into another partition on the machine. The installation went great and when the machine booted, the grub menu popped up and I could see the option for Ubuntu Studio and the vanilla Ubuntu OS'. The problem was that this version of grub, installed by the Studio installer, didn't look great and insisted on putting Studio at the top of the list, and therefore as the main OS to boot. I use the standard Ubuntu more often, so I booted into that and ran sudo grub-install dev/sda. That worked OK and now Ubuntu boots as normal. Only problem is that the Grub menu doesn't show up and doesn't give me a chance to choose the other OS. Running sudo os-prober shows that it can find ubuntu studio, it doesn't give me a chance to boot it. Any ideas as to how I can fix this problem? Cheers in advance. EDIT: followed instructions here and saw the boot menu, but the only boot options present were for the standard installation of Ubuntu.

  Read the article

• JRockit R28 "Ropsten" released

  - by tomas.nilsson

  R28 is a major release (as indicated by the careless omissions of "minor" and "revision" numbers. The formal name would be R28.0.0). Our customers expect grand new features and innovation from major releases, and "Ropsten" will not disappoint. One of the biggest challenges for IT systems is after the fact diagnostics. That is - Once something has gone wrong, the act of trying to figure out why it went wrong. Monitoring a system and keeping track of system health once it is running is considered a hard problem (one that we to some extent help our customers solve already with JRockit Mission Control), but doing it after something occurred is close to impossible. The most common solution is to set up heavy logging (and sacrificing system performance to do the logging) and hope that the problem occurs again. No one really thinks that this is a good solution, but it's the best there is. Until now. Inspired by the "Black box" in airplanes, JRockit R28 introduces the Flight Recorder. Flight Recorder can be seen as an extremely detailed log, but one that is always on and that comes without a cost to system performance. With JRockit Flight Recorder the customer will be able to get diagnostics information about what happened _before_ a problem occurred, instead of trying to guess by looking at the fallout. Keywords that are important to the customer are: • Extremely detailed, always on, diagnostics information • No performance overhead • Powerful tooling to visualize the data recorded. • Enables diagnostics of bugs and SLA breaches after the fact. For followers of JRockit, other additions are: • New JMX agent that allows JRMC to be used through firewalls more easily • Option to generate HPROF dumps, compatible with tools like Eclipse MAT • Up to 64 BG compressed references (previously 4) • View memory allocation on a thread level (as an Mbean and in Mission Control) • Native memory tracking (Command line and Mbean) • More robust optimizer. • Dropping support for Java 1.4.2 and Itanium If you have any further questions, please email [email protected]. The release can be downloaded from http://www.oracle.com/technology/software/products/jrockit/index.html

  Read the article

• Collaboration using github and testing the code

  - by wyred

  The procedure in my team is that we all commit our code to the same development branch. We have a test server that runs updated code from this branch so that we can test our code on the servers. The problem is that if we want to merge the development branch to the master branch in order to publish new features to our production servers, some features that may not have been ready will be applied to the production servers. So we're considering having each developer work on a feature/topic branch where each of them work on their own features and when it's ready, merge it into the development branch for testing, and then into the master branch. However, because our test server only pulls changes from the development branch, the developers are unable to test their features. While this is not a huge issue as they can test it on their local machine, the only problem I foresee is if we want to test callbacks from third-party services like sendgrid (where you specify a url for sendgrid to update you on the status of emails sent out). How to handle this problem? Note: We're not advanced git users. We use the Github app for MacOSX and Windows to commit our work.

  Read the article

• Unable to access ubuntu through windows boot manager

  - by Arvind

  I am having an ASUS K55VM....it came with DOS....to this Windows 7 was installed...now i am planned to add another OS ie Ubuntu...my computer had 4 partitions of 240GB 230GB 230GB and 230GB....i changed this to 5 parts....243GB 230GB 230GB 150GB and an 80GB...i installed Ubuntu 12.04 to the 80GB partition through a USB flash drive....it installed fine...however the problem is during the Boot option in Windows Boot manager when i choose Ubuntu...this what is displayed... Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: 1.Insert your Windows installation disc and restart your computer. 2.Choose your language settings, and then click "Next." 3.Click "Repair your computer." If you do not have this disc, contact your system administrator or computer manufacturer for assistance. File: \ubuntu\winboot\wubildr.mbr Status: 0xc000000e Info: The selected entry could not be loaded because the application is missing or corrupt. I tried to change the boot option for the OS and made Ubuntu as my first option....It worked...however windows 7 does not show up in GRUB....in this fear i did the following: Restarted my pc changed boot option 1 to windows. Formatted the drive to which Ubuntu was installed(80GB one)through windows. Restarted again. The problem persists....Windows boot manager shows Ubuntu still and when i choose this it gives two lines one like: grub rescue....but my windows 7 is working perfectly fine. Now want a solution to remove Ubuntu from the windows boot option and reinstall completely...

  Read the article

• How to get tilemap transparency color working with TiledLib's Demo implementation?

  - by Adam LaBranche

  So the problem I'm having is that when using Nick Gravelyn's tiledlib pipeline for reading and drawing tmx maps in XNA, the transparency color I set in Tiled's editor will work in the editor, but when I draw it the color that's supposed to become transparent still draws. The closest things to a solution that I've found are - 1) Change my sprite batch's BlendState to NonPremultiplied (found this in a buried Tweet). 2) Get the pixels that are supposed to be transparent at some point then Set them all to transparent. Solution 1 didn't work for me, and solution 2 seems hacky and not a very good way to approach this particular problem, especially since it looks like the custom pipeline processor reads in the transparent color and sets it to the color key for transparency according to the code, just something is going wrong somewhere. At least that's what it looks like the code is doing. TileSetContent.cs if (imageNode.Attributes["trans"] != null) { string color = imageNode.Attributes["trans"].Value; string r = color.Substring(0, 2); string g = color.Substring(2, 2); string b = color.Substring(4, 2); this.ColorKey = new Color((byte)Convert.ToInt32(r, 16), (byte)Convert.ToInt32(g, 16), (byte)Convert.ToInt32(b, 16)); } ... TiledHelpers.cs // build the asset as an external reference OpaqueDataDictionary data = new OpaqueDataDictionary(); data.Add("GenerateMipMaps", false); data.Add("ResizetoPowerOfTwo", false); data.Add("TextureFormat", TextureProcessorOutputFormat.Color); data.Add("ColorKeyEnabled", tileSet.ColorKey.HasValue); data.Add("ColorKeyColor", tileSet.ColorKey.HasValue ? tileSet.ColorKey.Value : Microsoft.Xna.Framework.Color.Magenta); tileSet.Texture = context.BuildAsset<Texture2DContent, Texture2DContent>( new ExternalReference<Texture2DContent>(path), null, data, null, asset); ... I can share more code as well if it helps to understand my problem. Thank you.

  Read the article

• Apache Not Accepting a Path in My Home Folder

  - by Promather

  I have trying to set up an Apache site to use a folder in my home folder without any success. I exactly followed the steps in this page: https://help.ubuntu.com/community/ApacheMySQLPHP yet I did not succeed; I keep getting error 403, which says that the server doesn't have permission to access the requested page. I searched forums and many suggested changing the permission of the folder. I went straight away and set the permission to 777, but that didn't solve the problem. I made another search and somebody gave me a clue, which is that it could be because my home folder is encrypted. I believe this could be the problem, but: What is the relation between encryption and Apache? I suppose Apache server is requesting the file from the system, rather than trying to access the file bytes! Is there anyway to solve this problem? I don't want to move the folder to /var/www because I am using this Apache for testing, so I want whatever change I make to be immediately reflected, rather than having to copy files which is error prone.

  Read the article

• Since a few days, Dropbox stopped syncing

  - by Fabio

  Theres a new problem with nautilus-dropbox and is the worst for a service like Dropbox: stopped syncing and their tech support don't believe their users. The problem is: start dropbox it downloads index creates folders start to download files stop downloading files or the speed is like 0.3k/seg even deleting everything doesn't work, even syncing a single folder with a few files, not even configuring a different limit speed or let all your bandwith, nothing works for me and i have found many users with the same problem. it's strange, i have two computers with ubuntu 14.04 and one with windows 7, and in one of the linux machines it works fine, but not in the other one. Both of them are x64. The answers from the tech support starts with "delete everything and reinstall" to "you may be blocking port 443", yeah, sure (and if i do that half of internet dissapears, idiot), but nothing works. Someone has some idea? i cant find any log file (at least a text log file like in /var/log) to understand what is dropbox doing and what is not working. PS: sorry for my "english", is not my language Examples: dropbox slow on ubuntu 14.04 Dropbox does not sync on ubuntu 14.04 Dropbox Status (in spanish but is the same thing) fabio@canopus:~$ dropbox status Sincronizando (Quedan 330 archivos., Faltan 9 días.) Descargando 330 archivos... (0,3 KB/s, Faltan 9 días.) 9 days for 330 files / 100Mb

  Read the article

• Best practice with branching source code and application lifecycle

  - by Toni Frankola

  We are a small ISV shop and we usually ship a new version of our products every month. We use Subversion as our code repository and Visual Studio 2010 as our IDE. I am aware a lot of people are advocating Mercurial and other distributed source control systems but at this point I do not see how we could benefit from these, but I might be wrong. Our main problem is how to keep branches and main trunk in sync. Here is how we do things today: Release new version (automatically create a tag in Subversion) Continue working on the main trunk that will be released next month And the cycle repeats every month and works perfectly. The problem arises when an urgent service release needs to be released. We cannot release it from the main trunk (2) as it is under heavy development and it is not stable enough to be released urgently. In such case we do the following: Create a branch from the tag we created in step (1) Bug fix Test and release Push the change back to main trunk (if applicable) Our biggest problem is merging these two (branch with main). In most cases we cannot rely on automatic merging because e.g.: a lot of changes has been made to main trunk merging complex files (like Visual Studio XML files etc.) does not work very well another developer / team made changes you do not understand and you cannot just merge it So what you think is the best practice to keep these two different versions (branch and main) in sync. What do you do?

  Read the article

• How can we make agile enjoyable for developers that like to personally, independently own large chunks from start to finish

  - by Kris

  We’re roughly midway through our transition from waterfall to agile using scrum; we’ve changed from large teams in technology/discipline silos to smaller cross-functional teams. As expected, the change to agile doesn’t suit everyone. There are a handful of developers that are having a difficult time adjusting to agile. I really want to keep them engaged and challenged, and ultimately enjoying coming to work each day. These are smart, happy, motivated people that I respect on both a personal and a professional level. The basic issue is this: Some developers are primarily motivated by the joy of taking a piece of difficult work, thinking through a design, thinking through potential issues, then solving the problem piece by piece, with only minimal interaction with others, over an extended period of time. They generally complete work to a high level of quality and in a timely way; their work is maintainable and fits with the overall architecture. Transitioning to a cross-functional team that values interaction and shared responsibility for work, and delivery of working functionality within shorter intervals, the teams evolve such that the entire team knocks that difficult problem over. Many people find this to be a positive change; someone that loves to take a problem and own it independently from start to finish loses the opportunity for work like that. This is not an issue with people being open to change. Certainly we’ve seen a few people that don’t like change, but in the cases I’m concerned about, the individuals are good performers, genuinely open to change, they make an effort, they see how the rest of the team is changing and they want to fit in. It’s not a case of someone being difficult or obstructionist, or wanting to hoard the juiciest work. They just don’t find joy in work like they used to. I’m sure we can’t be the only place that hasn’t bumped up on this. How have others approached this? If you’re a developer that is motivated by personally owning a big chunk of work from end to end, and you’ve adjusted to a different way of working, what did it for you?

  Read the article

• Facebook and flash - why doesn't facebook recognise that I have flash installed?

  - by jaminday

  For some reason when I try to upload photos to facebook from the website, it tells me I need to upgrade my flash player: I definitely have flash installed, as can be seen in the picture, and working fine in youtube etc. My question is two-fold: 1) Does anyone know if this a problem with the version of flash I'm running, Ubuntu, or facebook itself? I get the same problem in Chrome and Firefox, so I know it's not the browser. 2) Is there a workaround or fix for this? As far as I can tell I'm running the very latest flash (on 64-bit Ubuntu 10.10) - but maybe that's the problem? Note: Before everyone starts jumping up and down about using Shotwell or Digikam or some such to upload photos to facebook, I know about these (and do use Shotwell at times). Unfortunately Shotwell only lets you upload to a Profile, but doesn't (as far as I can tell) let you upload to a facebook Page of which I am an administrator, so I am forced do it through the website. Using the simple uploader as seen in the first picture is horribly slow and tedious, and often times out while uploading. Of course if anyone knows of any alternate ways to upload to facebook pages I'd love to hear 'em!

  Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >