Search Results

Search found 24623 results on 985 pages for 'linux'.

Page 390/985 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• Using udev to create a character device based on a driver being loaded

  - by SteveCB

  I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

  Read the article

• Three server processes consume no more than 50% of Dual Core CPU

  - by thor

  I have three processes running on Intel Core 2 Duo CPU. From watching output of 'top' and graphs of CPU load (drawn by MRTG, data collection via SNMP) I can see that CPU load is never more than 50%, and, most of the day, when those processes are busy CPU load has a ceiling at 50 %. I mean, CPU load grows up to 50% in the morning and stays there until late evening. My first thought was that only one core was used at 100% thus giving 50% of both CPUs. But, as there are three processes running and from 'top' I see that both cores are being loaded, so this is not the case. schedtool shows that CPU affinity for those three processes is at default, 0x03, allowing them to use both cores. If I force one process to one core (schedtool -a 0x01), and two others to second (schedtool -a 0x02), cumulative usage grows beyond 50%. Why three processes seem to consume only 50% of two cores? Why forcing them to different CPUs allows usage to grow higher? Any hints? P.S. Processes in question are Counter-Strike servers.

  Read the article

• Ubuntu/ Gnome : Open an application is a specific workspace

  - by bguiz

  How do tell an application to open in a specific workspace? More info: I like to have my C++ IDE in workspace 2, my Java IDE in workspace 3, and my email, browser and miscellaneous in workspace four. I also use a shell script that executes upon log in: #!/bin/bash gnome-terminal & # WS 1 netbeans-6-9-1 & # WS2 qtcreator-2-0-1 & # WS 3 firefox & # WS 4 thunderbird & # WS 4 Of course currently it all opens in the curent workspace... Is there a way for me to specify which workspace each command should start in? Thanks in advance!

  Read the article

• Comparing 2 (or 3 Files If Possible) "Line By Line"

  - by PythEch

  I want to find out the differences of 2 (or 3 files if possible) line by line. Diff utils can do this, however it gives inaccurate results. Because, 2 files have exact number of lines which is "134". But diff gives me "Added Lines" and "Removed Lines". However this is wrong, they have exact the same number of lines, there is no added or removed lines. The text files which I want to find differences of them, have only numbers written, maybe that's why that algortihm fails. I couldn't find any option to prevent that, however I may be wrong, I mean there should be an option for that, but again, I couldn't find. This is what I get (5am.txt vs 6am.txt, there is a huge problem): This is what I want (6am.txt vs 7am.txt, still has problems): But, first the first image still has this problem, at the last lines. Edit: After I figured out that there is no utility to do this, I handled myself. I almost did the same thing as what RedGrittyBrick have done. This script imitates diff utility so I (or you) can use it with diff2html. To use it with diff2html, just change line diff_stdout = os.popen("diff %s" % string.join(argv[1:]), "r") to diff_stdout = os.popen("script.py %s" % string.join(argv[1:]), "r") and name this script whatever you want: import sys f1=open(sys.argv[1],"r") f1_read=f1.readlines() f1.close() f2=open(sys.argv[2],"r") f2_read=f2.readlines() f2.close() changed={} first_c = "" for n in range(len(f1_read)): if f1_read[n]!=f2_read[n]: if first_c == "": first_c=n+1 changed[first_c]=n+1 else: first_c="" #Let's imitate diff-utils... for (x, y) in changed.items(): print "%d,%dc%d,%d" % (x,y,x,y) for i in range(x,y+1): sys.stdout.write("< %s" % f1_read[i-1]) print "---" for i in range(x,y+1): sys.stdout.write("> %s" % f2_read[i-1]) Final results:

  Read the article

• iptables -- OK, **now** am I doing it right?

  - by Agvorth

  This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

  Read the article

• SASL - Plaintext password not accepted - Encrypted works

  - by leviathanus

  I have a very strange issue! SASL does not work properly, as it does not accept plain-text passwords (like Outlook sends them) Oct 2 10:35:09 srf cyrus/imap[4119]: accepted connection Oct 2 10:35:09 srf cyrus/imap[4119]: badlogin: [217.XX.XXX.140] plaintext [email protected] SASL(-1): generic failure: checkpass failed Now I switch to "Encrypted password" in Thunderbird. I have the same issue as Outlook above on Thunderbird if I turn on "Plain Password"): Oct 2 10:40:40 srf cyrus/imap[14644]: accepted connection Oct 2 10:40:41 srf cyrus/imap[14622]: login: [217.XX.XXX.140] [email protected] CRAM-MD5 User logged in Same with Postfix: Without Oct 2 10:42:48 srf postfix/smtpd[17980]: connect from unknown[217.XX.XXX.140] Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: SASL authentication failure: cannot connect to saslauthd server: Permission denied Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: SASL authentication failure: Password verification failed Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: unknown[217.XX.XXX.140]: SASL PLAIN authentication failed: generic failure With "Encrypted password": Oct 2 10:45:27 srf postfix/smtpd[21872]: connect from unknown[217.XX.XXX.140] Oct 2 10:45:28 srf postfix/smtpd[21872]: 50B3A332AAB: client=unknown[217.XX.XXX.140], sasl_method=CRAM-MD5, [email protected] Oct 2 10:45:28 srf postfix/cleanup[21899]: 50B3A332AAB: message-id=<[email protected]> Oct 2 10:45:28 srf postfix/qmgr[6181]: 50B3A332AAB: from=<[email protected]>, size=398, nrcpt=1 (queue active) Oct 2 10:45:28 srf postfix/smtpd[21872]: disconnect from unknown[217.XX.XXX.140] Config: /etc/imapd.conf:sasl_mech_list:LOGIN PLAIN CRAM-MD5 and /etc/postfix/sasl/smtpd.conf:mech_list: LOGIN PLAIN CRAM-MD5 I have no idea where to dig. Please advise.

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• Debian: video problems with VLC

  - by kemp

  I have a problem playing AVI divx files with VLC. Yesterday upon start VLC showed an error message complaining about divx codecs and refused to proceed. Today the player starts but the video is squashed horizontally (it occupies roughly 1/4th of the VLC window which is for the other part black). I'm on an updated testing system, and before yesterday VLC was playing fine. In the meantime - after a recent dist-upgrade - I cannot run X with proprietary ATI drivers anymore, I have to use the FOSS radeonhd ones instead. I don't know if that's related but I thought it could be worth mentioning (and by the way if anyone has suggestions about this problem too, that'd be very much appreciated). How can I fix VLC's problem?

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• How do you persist installed software & configurations on an Amazon EC2 instance?

  - by Richard

  I've gotten a base Debian AMI up and running and now I need to know the best way to maintain it. I've ran the updates (aptitude update/upgrade) and installed/configured my software (Apache, Ruby, etc.) but if I reboot the instance or start a new one I'll have to do all this work over again. How do you persist these types of things over a reboot? Do you build a new AMI every time you adjust some tiny piece of the system? Or is there some way to feed it a script on startup that configures it in "real-time"? I know I could go all the way with a Reductive Labs Puppet style setup but that's a bit too much for my needs right now (1-2 servers). Any best practices on this? Update: I found a bit of information on using User-Data to run scripts at instance boot time.

  Read the article

• lamp server permissions on development server

  - by user101289

  I run a LAMP server on a ubuntu laptop I use only for development. I am not greatly concerned with security, since the server is never accessible outside the local network, and it's turned off when I'm not using it. My question is what is the simplest and 'best' way to set permissions/users/groups so that when my myself user creates, edits or writes files in the webroot, I won't need to go through and CHMOD / CHOWN everything back to the www-data user? Should I add myself to the www-data group? Or chown the webroot to www-data:myself? Or is there a best practice for this situation so I don't have to keep re-setting the ownership of these files? Thanks

  Read the article

• Removing partition to install OS?

  - by Shane

  So i have a computer that has 2 hard drives and i installed Ubuntu server on it. I used LVM to connect the two. So i tried to put windows back on it but it failed because it said it couldn't position the drive and then when i booted again the OS couldn't be found. So i booted it with the Ubuntu setup disc but now when it goes to partition it says that the position can not be modified because its already in use. I am asking if there is a way i can just remove everything and start fresh?

  Read the article

• How do I find out with Ubuntu whether my computer has a SATA or PATA hard drive interface?

  - by Pieter

  Is there a tool for Ubuntu that will detect whether I have a SATA or a PATA hard drive interface, even if there's no hard drive inserted?

  Read the article

• Descending list ordered by file modification time

  - by user62367

  How can i generate a list of files in a directory [e.g.: "/mnt/hdd/PUB/"] ordered by the files modification time? [in descending order, the oldest modified file is at the lists end] ls -A -lRt would be great: https://pastebin.com/raw.php?i=AzuSVmrJ but if a file is changed in a directory it lists the full directory...so the pastebined link isn't good [i don't want a list ordered by "directories", i need a "per file" ordered list] os: openwrt..[no perl - not enough space for it :( + no "stat", or "file" command] Thank you!

  Read the article

• Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

  - by Andrew Bolster

  I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

  Read the article

• Impossible to stop raid device

  - by Traroth

  I'm trying to stop a RAID disk in order to replace it by a new one, as this one is not working properly. I'm typing mdadm --stop /dev/md1, and I'm getting an error message: mdadm: fail to stop array /dev/md1: Device or resource busy I'm getting this message even if I reboot the server, and I can't see a process that could cause this. The server is working under a Debian with a 2.6.18-4-amd64 kernel. Could you help? Edit: Mote details about what my colleague tried out. After unmounting sda1, the command mdadm --remove /dev/md0 /dev/sda1 worked. But now, we still have an error message after mdadm --remove /dev/md1 /dev/sda5: mdadm: hot remove failed for /dev/sda5: Device or resource busy I still don't understand completly how the different partitions are mounted, so I suppose there is something I don't understand in the currenct situation...

  Read the article

• Choose between multiple keyboard layouts for different users in GDM3

  - by Daniel Wagner

  I am trying to set up a computer with multiple users each with different preferred keyboard layouts. The biggest sticking point right now is allowing each to log in comfortably. GDM used to offer a way to choose keyboard layout, but I can't discover how to set this up in GDM3. All the solutions I found when Googling this problem suggest changing the keyboard layout in xorg.conf, but that only sets a different single layout and still does not seem to allow me to change the layout between multiple choices. How can I allow multiple layouts when logging in?

  Read the article

• Debian Testing installs Iceweasel ESR (severely outdated)?

  - by Lucas Phillips

  I just reinstalled Debian Testing, and for some reason, instead of Iceweasel 25, I have 17. The installed and candidate versions are both 17.0.9esr-1~deb7u1. apt-get update && apt-get upgrade does nothing, and it seems that version 17 is the latest for this install. I was on Debian Testing before, and Iceweasel was at the latest version. Even Debian Stable had an Iceweasel version 20. Why would it be trying to install ESR now?

  Read the article

• recovering a broken GNOME-desktop in debian wheezy

  - by morgon

  an hour ago I had a working gnome-desktop on my debian system (thinkpad x121e). Then I installed compiz that crashed. After a reboot the gnome-desktop no longer started. Then I did some upgrades with aptitude, all gnome-packages seem to be there, but it is still not working. On startup I get a login-dialog, when I login there is no desktop, only some window-manager running that allows me to start a terminal. When I run "gnome-session" I get the error message "failed to load session "gnome". So how do I get back to a working desktop? I have tried "tasksel install gnome-desktop --new-install" but that just displays a progress window that after half an hour still shows 0%. Can someone help me please? I have tried "

  Read the article

• Why does Gnome use the order-by triangle the opposite way as Windows does?

  - by StackedCrooked

  I included this screenshot for clarity: The triangle is (according to my logic) wrongly rotated. Is this a bug, or an intentional choice?

  Read the article

• Error headers: ap_headers_output_filter() after putting cache header in htaccess file

  - by Brad

  Receiving error: [debug] mod_headers.c(663): headers: ap_headers_output_filter() after I included this within the htaccess file: # 6 DAYS <FilesMatch "\.(ico|pdf|flv|jpg|jpeg|png|gif|js|css|swf)$"> Header set Cache-Control "max-age=518400, public" </FilesMatch> # 2 DAYS <FilesMatch "\.(xml|txt)$"> Header set Cache-Control "max-age=172800, public, must-revalidate" </FilesMatch> # 2 HOURS <FilesMatch "\.(html|htm)$"> Header set Cache-Control "max-age=7200, must-revalidate" </FilesMatch> Any help is appreciated as to what I could do to fix this?

  Read the article

• Cobbler 2.2.2 problems

  - by Peter

  I have setup a dedicated LAN for Cobbler tests. My setup is: Cobbler server: openSUSE 12.3, cobbler 2.2.2 (from openSUSE repos) Imported distros: Centos 6.5, Red Hat 6.5, Red Hat 7.0, openSUSE 13.1 Target Machine: VMs in a Windows 7 Virtualbox Systems provisioning works OK, but I have some problems. The first one is that cobbler does not honor the "pxe_just_once: 1" setting. When the setup of the target OS is finished, after the reboot the target systems continues to PXE boot! The second problem is that the target server is not correctly configured! See my setup: cobbler system report --name=test Name : test TFTP Boot Files : {} Comment : Fetchable Files : {} Gateway : 192.168.0.1 Hostname : testcob1.example.com Image : IPv6 Autoconfiguration : False IPv6 Default Device : Kernel Options : {} Kernel Options (Post Install) : {} Kickstart : <<inherit>> Kickstart Metadata : {} LDAP Enabled : False LDAP Management Type : authconfig Management Classes : [] Management Parameters : <<inherit>> Monit Enabled : False Name Servers : ['192.168.0.1', '8.8.8.8'] Name Servers Search Path : [] Netboot Enabled : False Owners : ['admin'] Power Management Address : Power ID : Power Password : Power Management Type : ipmitool Power Username : Profile : RHEL-6.5-x86_64 Proxy : <<inherit>> Red Hat Management Key : <<inherit>> Red Hat Management Server : <<inherit>> Repos Enabled : False Server Override : <<inherit>> Status : testing Template Files : {} Virt Auto Boot : <<inherit>> Virt CPUs : <<inherit>> Virt Disk Driver Type : <<inherit>> Virt File Size(GB) : <<inherit>> Virt Path : <<inherit>> Virt RAM (MB) : <<inherit>> Virt Type : <<inherit>> Interface ===== : eth0 Bonding Opts : Bridge Opts : DHCP Tag : DNS Name : Master Interface : Interface Type : IP Address : 192.168.0.200 IPv6 Address : IPv6 Default Gateway : IPv6 MTU : IPv6 Secondaries : [] IPv6 Static Routes : [] MAC Address : Management Interface : True MTU : Subnet Mask : 255.255.255.0 Static : True Static Routes : [] Virt Bridge : So, although I have setup the hostname and the network interface of the target system, after the setup, the hostname is set to localhost.localdomain and eth0 is configured as a DHCP not static! How can I find the problem and fix it? Note that I have synced and restarted cobbler a couple of times, but the problems persists.

  Read the article

• How to write image of a floppy disk to a flash drive?

  - by Usman Ajmal

  I have created an image of a floppy disk by executing: dd if=/dev/fd0 of=/home/myFloppy.img My floppy disk is no more working now. So I am thinking now if it's possible to write the image of that floppy to a flash drive and then i may boot my machine from the flash drive. My machine's BIOS has the option of 'Boot from USB'.

  Read the article

• USB forwarding from dom0 to domU

  - by Karolis T.

  What are my options to forward two USB connected phones to xen guest? I've read about PCI-passthrough http://www.wlug.org.nz/XenPciPassthrough, but I'm sure usb controller in the server isn't a pci card. There's device level forwarding, but I need to forward two devices, this here doesn't say how to do it: http://www.olivetalks.com/2008/02/03/usb-forwarding-on-xen-it-just-does-not-work/ Would something as simple as: usbdevice = [ 'host:xxx', 'host:yyy', ] work? EDIT: I'm now starting a bounty. This is really important for me and for other people also, hoping someone who have this resolved will be able to help.

  Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >