Search Results

Search found 13817 results on 553 pages for 'net4 full'.

Page 390/553 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• Windows or Linux for VPN-VPN Bridge

  - by James

  I have the following network layout: Network1 ----VPN1-----Network2----VPN2----Network3 I can administer everything in Network1 only and my goal is to get to a box on Network3. I've been told by the admins of Network2 that it's not possible for them to route traffic from Network1 to Network3. I've finally been authorised to host a box in Network2 and I'm hoping with this I can set something up to resolve the issue. My question is should I set this up as a Windows or a Linux box. My initial thought was to use iptables to reroute requests but with my lack of experience with Windows Server (used for something or other in Network2) I'm not sure if this will work. My head's full of questions like: - can I get an ip without logging in to a windows domain? - if I do get an ip, do Windows Servers manage routing through the VPN? - can I make a linux box authenticate with Windows Server to log on to the domain? - would it just be easier to set up a windows box? - is it possible to configure a windows box to do routing from Network1 to Network3? Has anyone done anything like this before? Had experience managing Windows Server? Authenticated (or not as the case may be) to a Windows domain? I'd really appreciate your advice. It might be worth mentioning that the overall objective is to establish a telnet connection from a box on Network1 to a box on Network3.

  Read the article

• IPCop server slows down download speed

  - by noocyte

  I have an IPCop server running at home, been doing just fine for ~5 months, but last week I suddenly started getting time-outs and slow downloads from the 'net. I first thought that this was my ISP acting up, then I thought it might be one of my 3 switches or some of my cabling. In due order I've tested everything above and found them all to be working as they should. The only factor remaining is my IPCop server. Facts: I've got a 15/15 Mbit line (fiber) and I get ~15 Mbit upload, but only 0.5 Mbit download with the IPCop box as router (ISP router set in bridge mode). If I connect without the IPCop box (using the ISP router) I get ~12 Mbit upload and ~15 Mbit download. The load on the IPCop box appears to be light and it used to handle this traffic just fine 2 weeks ago. The memory usage is ~60%, I tried to restart it and test again, the memory fell to ~50% then (5 months of uptime). I'm thinking that one of my nics are busted, but I'm sort of perplexed that this could be the outcome; slow download but full speed upload. Anybody ever seen that happening before? Could it just be one of the nics that needs to be replaced? Will try that as soon as I can get my hands on a couple of new ones.

  Read the article

• VMware Fusion configuration files missing

  - by jdmuys

  I need to set up port forwarding to my VM in Fusion 5. Everywhere on the net, the solution is described as editing the file: /Library/Application Support/VMware Fusion/vmnet8/nat.conf However, on my install, that file doesn't exist. Neither does the vmnet8 directory. Here is the full content of VMware stuff I have in /Library/Application Support/: /Library/Application Support/ VMware/ VMware Fusion AdminWritable Shared vmInventory usbarb.rules VMware Fusion That's right: /Library/Application Support/VMware Fusion/ exists but is empty. And there is no VMware folder in other Library directories on my system. I am running OS X 10.8.2. I just reinstalled Fusion 5.02, no change. Meanwhile, I have 3 VMs that work just fine. So how am I supposed to set up port forwarding with Fusion 5? Thanks, JD Edit: in a hunch, I tried ps ax | grep natd which returned: 9646 ?? S 0:00.01 /Applications/VMware Fusion.app/Contents/Library/vmnet-natd -s 7 -m /Library/Preferences/VMware Fusion/vmnet8/nat.mac -c /Library/Preferences/VMware Fusion/vmnet8/nat.conf So it seems that the configurations files are now in the directory /Library/Preferences/VMware Fusion. I'll work from here and edit this question as I make progress.

  Read the article

• Open Source PDF reader for windows as an alternative to Adobe reader

  - by Tom Feiner

  With the latest javascript vulnerabilities in Adobe reader and bloat it has aquired over the years, I've been thinking of moving the network I'm in charge of to a different product for PDF reading on Windows. The ideal PDF reader should be something that is: Small in size (Adobe reader is more than 200MB these days after installation). As secure by default as possible (For example, javascript disabled by default). Nice looking and easy to use interface. Not bloated with features (I just want to read PDFs, that's it). Does not install any toolbars/unwanted add ons/spyware. Does not display any ads while viewing PDFs. Preferably Open Source. (this pretty much ensures no ads). Full Unicode support. Idealy , something like evince from gnome, will be the best option, but unfortunately that's not available on Windows. Foxit is an option, as it is small, and has a nice interface. But it still has javascript enabled by default which might lead to vulnerabilities - and it installs a toolbar , and displays ads while reading PDFs which is distracting. There is a site dedicated to Open Source PDF readers, pdfreaders.org, however, the Windows pdf readers each have their problems, mostly the interface is not as convenient (as evince, adobe or foxit). Here's a list of all PDF software from WikiPedia. There's a "Viewers" section for each OS. What Windows PDF reader would you recommend ?

  Read the article

• Crash dump analysis

  - by Ryan Ries

  I hope this isn't a stupid question, and if it is, then I want to at least get it over with so I don't feel so dumb in the future. Here we are, loading up a Windows crash dump with Windbg. Here are the first few lines of the debugger output: 0: kd> .dumpdebug ----- 64 bit Kernel Summary Dump Analysis DUMP_HEADER64: MajorVersion 0000000f MinorVersion 00001db1 ... The MinorVersion I mostly understand. It's hexadecimal and it translates to 7601 in decimal. Windows admins would already be able to tell from that that this must be either a Win7 x64 machine or a 2k8 R2 machine with SP1. But isn't 7601 the build number? It's supposed to be Major.Minor.Build/Revision... right? Also I don't understand the MajorVersion. It should be 6. This version of Windows is 6. But isn't 0000000f in hexadecimal 15 in decimal? The full version string of this version of Windows, when you launch the Command Prompt for instance, is 6.1.7601. If 7601 is the MinorVersion, then what is 1 and what is 6? And why does the crash dump say 0F?

  Read the article

• MacBook Pro battery capacity 65K mAh

  - by Alexander Gladysh

  I have a 15" MacBook Pro 3.1 (that is Late 2007 model AFAIR). I've bought it new a couple of years ago. Recently its on-battery power lifespan became very short (30 to 10 minutes). When my notebook turns itself off due to "low battery" and I press the small button on the battery itself, all LED lights are alight, indicating full charge. When I plug in the power adapter, my Mac displays that "battery is fully charged, finishing charging process" (I have a Russian OS X 10.5.7, so that is a rough translation), but the LEDs on battery itself display (seemingly accurate) status that there are one or two "LEDs still not charged". My battery have as few as 37 recharge cycles (yes, I've neglected calibration over the time I've used it). Battery info programs like iBatt2 report battery capacity of 65 337 mAh (with by-design capacity of 5600 mAh). I get it that something went wrong with battery electronics. I've tried resetting my Mac's PRAM and SMC, it did not changed anything. Now I'm trying to recalibrate the battery, but looks like it does not help as well. Will try to recalibrate it several times in a row. I'd buy a new battery if I knew if it is battery fault, not a notebook's. Any suggestions? Update: After recalibration, my battery status now displays battery capacity of 1500 mAh. But with every recalibration (or simply when I use notebook without power adapter plugged in) this number changes in the range from 200 mAh to 1700 mAh. LEDs on battery now are synchronous with what nodebook thinks on the charge level. Also I've noticed that cycle count changes rather slowly. It is now 39, it was 37 when I've started recalibration, and I went through the process at least ten times... So, the main question is: does it look like that replacing the battery would help me (or does it look like this is notebook's problem)? I guess I should try replacing the battery.

  Read the article

• rr.com appended to URL and I don't know why

  - by Steph

  I've been having some pretty bad and intermittent internet connectivity issues. I keep getting timeouts on my browsers, or what appears to be timeouts on my browsers. In Chrome it's generally error 21. FF it times out. And so on. While this is happening, I can go into the command line and ping or traceroute the same domain and it works fine. I use my cellphone on the same network and it's fine connecting to the same domain. And when it fails, it's all domains that are down in all browsers, chrome, FF, etc. I also noticed that when I try to connect to 192.168.1.1 it says in chrome did you mean www.192.168.1.1rr.com but when I enter https://192.168.1.1 it's fine. It only seems to do this in Chrome. This is making me think I have a virus. I did some researching about something called road runner, but I can't find any related traces. I also ran a full virus scan using nod32 (eset) and nothing. Any suggestion or help would be greatly appreciated. The intermittent loss of total internet access is really annoying and I'm worried about why it's trying to append the rr.com domain in Chrome. I suspect I'm dealing with two different issues, but you never know. Also for the DNS I'm using Google's DNS servers, the famous 8.8.8.8 and 8.8.8.4

  Read the article

• External Hard Drive Won't Mount - MAC OSX

  - by dtj

  I have a Western Digital hard drive that's about 4 or 5 years old. It's 500 GB, USB. I use it to backup my Mac every so often. I had it partitioned: 1 side for full backups, and the other side for general storage of music, installers, etc. I decided to get rid of the partition today and dump all the data. So I opened disk utility, and hit 'erase'. It started thinking and then disk utility crashed. After the crash, the hard drive won't mount, however disk utility still sees the drive, but not the individual volume within. I tried booting up Disk Warrior and no luck there either. It has the drive as an "unknown drive". When I hit rebuild, it goes through all it steps and then stops cause of this error: The drive "unknown" is severely damaged and DiskWarrior is unable to determine its case sensitivity What can I do at this point? There isn't any physical damage to the drive. Never been dropped or anything.

  Read the article

• Excel VBA: select every other cell in a row range to be copied and pasted vertically

  - by terry alexander

  i have a 2200+ page text file. It is delivered from a customer through a data exchange to us with astericks to separate values and tildes (~) to denote the end of a row. The file is sent to me as a text file in Word. Most rows are split in two (1 row covers a full line and part of a second line). i transfer segments (10 page chunks) of it at a time into Excel where, unfortunately, any zeroes that occur at the end of a row get discarded in the "text to columns" procedure. So, i eyeball every "long" row to insure that zeroes were not lost and manually re-enter any that were. Here is a small bit of sample data: SDQ EA 92 1551 378 1601 151 1603 157 1604 83 The "SDQ, EA, and 92" are irrelevant (artifacts of data transmission). i want to use Excel VBA to select 1551, 1601, 1603, and 1604 (these are store numbers) so that i can copy those values and transpose paste them vertically. i will then go back and copy 378, 151, 157, and 83 (sales values) so that i can transpose paste them next to the store numbers. The next two rows of data contain the same store numbers but give the corresponding dollar values. i will only need to copy the dollar values so they can be transpose pasted vertically next to unit values (e.g. 378, 151, 157, and 83). Just being able to put my cursor on the first cell of interest in the row and run a macro to copy every other cell would speed up my work tremendously. i have tried using activecell and offset references to select a range to copy but have not been successful. Does any have any suggestions for me? Thanks in advance for the help.

  Read the article

• Why are my Windows 7 updates continuously failing?

  - by Chris C.

  I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium x64 Edition. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about 4 months. Windows Updates aside, the system is usually quite stable. Thanks in advance for your help!

  Read the article

• Exchange Server 2010: move mailboxes from recoveded and mounted edb to user’s mailbox

  - by user36090

  One of our exchange servers crashed, and I am trying to recover the mailboxes. We had 1 exchange 2003 server named "apex" and 1 exchange 2010 server named "2008Enterprise. the exchange 2010 server named "2008Enterprise" crashed. I created a new exchange 2010 server named "Providence". I ran the command on Providence: New-MailboxDatabase -Recovery -Name JBCMail -Server Providence -EdbFilePath "c:\data\Exchange\Mailbox\Mailbox Database 0579285147\Mailbox Database 0579285147.edb" -LogFolderPath "c:\data\Exchange\Mailbox\Mailbox Database 0579285147" this command executed and finished without error I then ran the command: eseutil /p E00 this command was executed from the below directory: c:\data\Exchange\Mailbox\Mailbox Database 0579285147 I then mounted the JBCMail with the mount command note: I do not have my full typed command. Inside my Exchange Management Console (EMC) I can view the new mailbox database named JBCMail. The JBCMail database is show as mounted on the exchange server named Providence. I can see the crashed Exchange server named 2008Exchange. In the EMC the crashed exchange server states the Copy Status under ServerConfiguration-Mailbox is ServiceDown. From here I need to recover three mailboxes The mail boxes are on the apex server. How do I move the mailboxs from apex to Providence? How do I restore the mailboxes from JBCmail mounted database to the user's mailbox? I do not fully understand how to use the Restore-Mailbox command because when I use this command it tries to restore the mailbox to the dead apex server. Restore-Mailbox -ID 'Jason Young' -RecoveryDatabase JBCMail

  Read the article

• MSI Installer error 2203; how to force permissions on installer directory?

  - by goober

  [Cross-Posted on StackOverflow.com as well because the question relates to development. Feel free to let me know where it best belongs.] Hi all, I'll try to bullet-point to keep it short: Background / Issue Trying to install ASP.NET MVC 3 RC on my Windows 7 machine. Uninstalled other versions of MVC (2 and 3 Beta 1). Ran the installer -- got a generic error, 2203. Log files said that it was a permissions error on C:\Windows\Installer. Checked C:\Windows\Installer -- sure enough, it's marked as read-only. I un-checked "Read-Only" in the folder properties and applied. It appears to open the dialog and apply to all files. However, when clicking properties again, the read-only box is backed to checked. Checked the security tab of the folder -- both system and the Administrators group have full access. I checked ownership -- the Administrators group is listed as an owner. Verified that I'm in the system as an Administrator (in fact, the only account in the Administrators group besides Administrator). So, what gives? Thanks in advance for any help you can provide!

  Read the article

• SQL Server Management Studio not scripting all objects

  - by Ian Boyd

  i've been attempting to script a database using SQL Server 2005 Management Studio. i cannot get it to script some objects. It scripts others, but skips some. i can provide detailed screen shots the options being selected including all tables the folder where the script files will go the folder being empty before scripting the scripting process saying Sucess when scripting a table the destination folder no longer empty, with a hundred or so script files the script of some tables not being in the folder. And earlier SSMS would not script some views. Is this a known thing that the the Generate Scripts task does not generate scripts? Update Known issue on Microsoft Connect, but Microsoft couldn't repro the steps, so they closed closed the ticket. Fails on SQL Server 2005, also fails on SQL Server 2008. Update Two Some basic questions: 1.What version of SQL Server? Microsoft SQL Server 2000 - 8.00.194 (Intel X86) Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Microsoft SQL Server 2008 - 10.0.2531.0 (Intel X86) Microsoft SQL Server 2005 Management Studio: 9.00.4035.00 Microsoft SQL Server 2008 Management Studio: 10.0.1600.22 2.What O/S are you running on? Windows Server 2000 Windows Server 2003 Windows Server 2008 3.How are you logging in to SQL server? sa/password Trusted authentication 4.Have you verified your account has full access to all objects? Yes, i have access to all objects. 5.Can you use the objects that fail to script? (eg: select top(10) * from nonScriptingTable) Yes, all objects work fine. SQL Server Enterprise Manager can script the objects fine. Update Three They fail no matter what version of SQL Server you script against. It wasn't a problem in Enterprise Manager: Client Tools SQL Server 2000 SQL Server 2005 SQL Server 2008 ============ =============== =============== =============== 2000 Yes n/a n/a 2005 No No No 2008 No No No Update Four No errors found in the database using: DBCC CHECKDB go DBCC CHECKCONSTRAINTS go DBCC CHECKFILEGROUP go DBCC CHECKIDENT go DBCC CHECKCATALOG go EXECUTE sp_msforeachtable 'DBCC CHECKTABLE (''?'')' Honk if you hate SSMS.

  Read the article

• chmod -R 777 / on ubuntu - numerous problems

  - by ncatnow

  A client has accidentally given the entire filesystem full permissions on their ubuntu 10.04 box. chmod -R 777 httpdocs/cd / As you can see they attempted to cd to the root, and instead gave chmod a fun parameter to play with. First sign of the problem was inability to use 'su', giving an authentication error. sudo also complained of a missing setuid bit. This was fixed by logging in as root from the machine itself, and running chmod +s /usr/bin/sudo. I can now sudo su and do what I need to as root. su still gives an authentication failure. I followed the advice here: http://swiss.ubuntuforums.org/showthread.php?t=1180661&page=2 chmod 0755 / chmod 0755 /* chmod 1777 /tmp chmod 0750 /root chmod 0700 /lost+found I then tried to reset root password. I still cannot su to become root, or su root. The system seems to be running fine. Are there any suggestions for getting su to work once again? Where can I look for more problems?

  Read the article

• SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified data

  - by eulerfx

  I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

  Read the article

• Force Windows Local Subnet Traffic through a Gateway

  - by Beerey

  Hi all, We are attempting to route all traffic from a certain machine to a gateway. This works ok for traffic destined for subnets outside of the machine's subnet. However, traffic to machines in the same subnet as the source machine goes through an On-Link gateway in Windows. This means that the default gateway is ignored, and traffic in a subnet (for example, 192.168.50.10 - 192.168.50.11) flows. Destination Netmask Gateway Interface Metric 192.168.50.0 255.255.255.0 On-link 192.168.50.214 276 This route can be deleted from Windows, but when the machine is rebooted it always comes back. Adding a persistant static route to the gateway with a lower metric doesn't work, since it will still try the On-Link gateway after the persistant route fails. Adding each machine in a VLAN isn't an option due to the setup we have Adding a startup script to delete the gateway isn't a great option either, since users will have full admin access to the machine and might disable the script. We cannot transperantly intercept all network traffic on the subnet using Gratuitous ARPs or transparent proxying, since there are other machines on the subnet which use a different gateway The only way we have gotten it to work is by adding a persistant route to the gateway for the subnet traffic, and deleting the On-link route on reboot. The question is then. Is there a way to permanently remove this On-link route If not, is there a way to otherwise force even local subnet traffic to go through a gateway?

  Read the article

• Install Linux Mint on PC without bootable CD

  - by crosenblum

  Unfortunately my PC's CD drive is not bootable; I have such a mixture of SATA and IDE drives, so until I have more money to redo my controller setup, I can't boot from any cd. Currently, I have a DVD burned with latest version of Linux Mint, and I have an USB drive with an old version of Mint. I have a partition ready to install Linx Mint into, but no idea how to install it, since I can only boot to my hard drive. I am totally unable to boot to CD, so that is definitely out. My main partition is WinXP Pro SP3. Is there software I can use to format my Linux partition, so that I can then just copy Mint over to that partition? Or is there a better way to install linux mint? I have to do it within Windows XP, since that's all that I can boot right now. I have considered Mint4Win, but that doesn't allow a full installation of Linux Mint. Any ideas?

  Read the article

• Lenovo Wi-Fi Replacement

  - by user22910

  I recently got my T500 with a very poor signal Wi-Fi, Thinkpad BGN, a Realtek chipset. I would like to replace my Wi-Fi card with either the Intel WiFi Link 5100 or 5300. However, I read somewhere that Lenovo specfically "whitelist" their Wi-Fi cards to only work with their laptops. I could not find any of the Intel Wi-Fi, moreover any Wi-Fi cards on the Lenovo site. So, I went to hunt around in Amazon and found several sellers. Plus what sort of card do I require? There is a difference between mini cards and the full sized card, though I do not know which one my laptop supports. Here are the specifications for my laptop: http://privatepaste.com/8b0537bce0 I would like to have confirmation which one of these specific cards as posted below will work on my laptop (or the one you recommend to have): Intel Wifi Link 5300 Intel WiFi Link 5100 - Network adapter - PCI Express Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft 2.0) Intel WiFi Link 5100 - Network adapter - PCI Express Half Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft) Intel WiFi Link 5300 - Network adapter - PCI Express Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft)

  Read the article

• SQL Server 2008 R2 transactional replication over VPN

  - by enashnash

  I'm having difficulty setting up replication over a VPN. I have a SQL Server 2008 R2, Enterprise Edition database on a Windows 2008 R2 Server. SQL Server is running on a non-standard port. I have set it up so that it is acting as its own distributor and have configured a publisher on this server. It is set as an updatable transational publication (yes, this is necessary). On this server, I have Routing and Remote Access enabled in order to be able to establish VPN connections. It is configured with a static IP address pool, of which the first in the range is always assigned to the server. I have assigned a test user a static address within this range (I don't know if this is necessary or not). All clients will be 2008 R2 versions, but could be SQL Express or standalone developer instances of the full product. I can establish a VPN connection from the client without problems and can see that the correct IP addresses are allocated. After connecting to the database to test that I can establish a connection, I realised that I needed to be able to connect to the database using the server name rather than an IP address - required for replication - which wouldn't work initially. I created an entry in the hosts file for the server on the client using the NETBIOS name of the server, and now I can connect to the server, from the client, using the SERVER\INSTANCE, PORT syntax, over the VPN. As it is the default instance on the server, I can also connect with simply SERVER, PORT syntax. After all that, I still get the following dreaded error: SQL Server replication requires the actual server name to make a connection to the server. Connections through a server alias, IP address, or any other alternate name are not supported. Specify the actual server name, 'SERVER\INSTANCE'. (Replication.Utilities). What have I missed? How do I get this to work? TIA

  Read the article

• High Sqlservr.exe Memory Usage

  - by user18576

  I have a problem with sqlservr.exe (version 2008). It use a more memory. I checked on windows taskbar manager, sqlservr.exe usage ( Mem usage - 8GB Ram). I dont know how can I fix it.Got the following metrics of the server using Perfmon: SQLServer:Buffer Manager Buffer cache hit ratio 13 SQLServer:Buffer Manager Page lookups/sec 46026128096 SQLServer:Buffer Manager Free pages 129295 SQLServer:Buffer Manager Total pages 997309 SQLServer:Buffer Manager Target pages 1053560 SQLServer:Buffer Manager Database pages 484117 SQLServer:Buffer Manager Reserved pages 0 SQLServer:Buffer Manager Stolen pages 383897 SQLServer:Buffer Manager Lazy writes/sec 384369 SQLServer:Buffer Manager Readahead pages/sec 69315446 SQLServer:Buffer Manager Page reads/sec 71280353 SQLServer:Buffer Manager Page writes/sec 12408371 SQLServer:Buffer Manager Checkpoint pages/sec 7053801 SQLServer:Buffer Manager Page life expectancy 735262 SQLServer:General Statistics Active Temp Tables 161 SQLServer:General Statistics Temp Tables Creation Rate 3131845 SQLServer:General Statistics Logins/sec 2336011 SQLServer:General Statistics Logouts/sec 2335984 SQLServer:General Statistics User Connections 27 SQLServer:General Statistics Transactions 0 SQLServer:Access Methods Full Scans/sec 34422821 SQLServer:Access Methods Range Scans/sec 2027247756 SQLServer:Access Methods Workfiles Created/sec 49771600 SQLServer:Access Methods Worktables Created/sec 28205828 SQLServer:Access Methods Index Searches/sec 4890715219 SQLServer:Access Methods FreeSpace Scans/sec 21178928 SQLServer:Access Methods FreeSpace Page Fetches/sec 21226653 SQLServer:Access Methods Pages Allocated/sec 41483279 SQLServer:Access Methods Extents Allocated/sec 4743504 SQLServer:Access Methods Extent Deallocations/sec 4806606 SQLServer:Access Methods Page Deallocations/sec 41419137 SQLServer:Access Methods Page Splits/sec 23834799 SQLServer:Memory Manager SQL Cache Memory (KB) 29160 SQLServer:Memory Manager Target Server Memory (KB) 8428480 SQLServer:Memory Manager Total Server Memory (KB) 7978472 Some body could help me please.And I really want to know the cause for the above.

  Read the article

• wget mirroring, subdomains and directories and cookies

  - by Jimmu

  Hi all, I have an account on a web page that is now "full" (ie I have used up all my allocated space) and I would like to make a mirror of that site. wget seems like the thing to use. The problem is that I would only like to mirror the sites the lie within this directory http://user.domain.com/room/2324343/transcript/ (and sub-directories). Whilst saving the correct stylesheets, javascripts and css etc which exist in different directories. There as also uploaded files that are linked to within the pages in the transcript directory (on different directories) that I would like to download/mirror (theses are in a variatey of formats .exe, .py, .png, .app (and many more)). There are also images that are on different severs that are on these pages. Also I would like it if the links (which are sometimes relative , sometimes absoulute (but to internal things), sometimes external ) worked correctly so that if they link to things that have been downloaded(mirrored) they work fine (without internet connection), but if they link to things that are external or havent been mirrored they link to the external site. Basically so they work as expected. Another problem is that you have to log in to acess the site. Can wget be used to acomplish this or is there a better way? either way how do I achive this? (I have asked this question at stackoverflow.com/questions/2190115/wget-mirroring-subdomains-and-directories-and-cookies but it was recommended that I try asking it here)

  Read the article

• Cygwin, ssh, and git on Windows Server 2008

  - by Paul

  Hi everyone. I'm trying to setup a git repository on an existing Windows 2008 (R2) server. I have successfully installed Cygwin & added git and ssh to the packages, and everything works perfectly (thanks to Mark for his article on it). I can ssh to localhost on the server, and I can do git operations locally on the server. When I try to do either from the client, however, I get the "port 22, Bad file number" error. Detailed SSH output is limited to this: OpenSSH_4.6p1, OpenSSL 0.9.8e 23 Feb 2007 debug1: Connecting to {myserver} [{myserver}] port 22. debug1: connect to address {myserver} port 22: Attempt to connect timed out without establishing a connection ssh: connect to host {myserver} port 22: Bad file number Google tells me that this means I'm being blocked, usually, by a firewall. So, double-checked the firewall settings on the server, rule is there allowing port 22 traffic. I even tried turning off the firewall briefly, no change in behavior. I can ssh just fine from that client to other servers. The hosting company swears that there's no other firewalls blocking that server on port 22 (or any other port, they claim, but I find that hard to believe). I have another trouble ticket into them, just in case the first support person was full of it, but meanwhile I wanted to see if anyone could think of anything else it can be. Thanks, Paul

  Read the article

• cpanel dns only / rdns questions

  - by Clear.Cache

  I started getting IPs from ARIN directly, instead of the data center I'm colocated at. Now I have to start applying rdns myself for my clients upon request, instead of having the NOC at the DC do this. That is obvious, since I am in full control over the IP delegation and therefore have nameserver authority. The question is, how do I "create" ptr / rdns records for my clients? My current server uses Cpanel / WHM with ns1/ns2.mycompany.com I also applied those as dns nameservers in the ARIN IP's whois record. How do I create rdns for my clients? Should I install Cpanel DNS Only on a entirely separate server and use this method instead? http://layer1.cpanel.net/ If so, how can I seamlessly transition over the dns records to that new dns server, retaining my ns1/ns2.mycompany.com and their ns1 and ns2 IP addresses? Even more important: I have to change the ns1/ns2 IPs to the new ones I retrieve from ARIN. How can this be done, avoiding downtime during the dns transition? On a side note, would it be easier to just install Cpanel DNS Only on a dedicated server and just use dns1.mycompany.com and dns2.mycompany.com with their own dedicated ns1/ns2 IPs from ARIN - and utilize this dns server for customers who request rdns? Would this be a more viable solution than using our current ns1/ns2.mycompany.com Nameservers? Is Cpanel DNS Only a standalone software that does not require Cpanel/WHM on another server? Is it possible to have redundant dns servers setup using this software solely, ns1 on one server and ns2 on another? Thanks.

  Read the article

• Laptop choice for development: MacBook Pro 17 vs Dell Studio XPS 16 vs HP Envy 15

  - by Shalan

  Hey! First things first - let me state that I am not intending to play games on this - I have narrowed down to these 3 purely based on specs and its individual brand reliability in the market. I intend to primarily use: Visual Studio 2008 Pro a lot (develop and deploy on Windows platforms) SQL Server 2005 Oracle 10g Adobe Photoshop CS4 Microsoft Expression Studio Google Sketchup I currently use a desktop PC (Core2Duo 2.66Ghz with 3GB DDRII memory) running Vista Business 32-bit - and I have to admit that, especially for Visual Studio, its quite sluggish to a point where it affects productivity. Furthermore, I intend to only use the notebook on a table - with a cooled surface, like granite :) - so I would appreciate people's input with regard to heat issues. Im aware that the Dell's primary exhaust gets blocked by the lid when open, but some reviews don't seem to place extraordinary emphasis on heat issues resulting from this. My options for the Dell/Alienware: Core i7 720QM 4GB DDRIII memory ATI mobility 3670 (512) 128GB Solid State Drive 16-inch Full HD RGB-LED LCD display (1080p) 3-year next-business-day support My configuration for the Apple MBP: Core2Duo 2.8Ghz (Im assuming the T9600) 4GB DDRIII memory 128GB Solid State Drive standard 1 year support The one advantage I think of with the MBP is that I can have the addition of OSX (though Im unsure what I would use it for, but purely to play around with a much-boasted-about OS) What are your thoughts on this, especially regarding build-quality, heat, performance and battery-life? Much thanks! ~shalan

  Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >