Search Results

Search found 22600 results on 904 pages for 'remote connection'.

Page 390/904 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

• Cisco ASA Site-to-Site VPN Dropping

  - by ScottAdair

  I have three sites, Toronto (1.1.1.1), Mississauga (2.2.2.2) and San Francisco (3.3.3.3). All three sites have ASA 5520. All the sites are connected together with two site-to-site VPN links between each other location. My issue is that the tunnel between Toronto and San Francisco is very unstable, dropping every 40 min to 60 mins. The tunnel between Toronto and Mississauga (which is configured in the same manner) is fine with no drops. I also noticed that my pings with drop but the ASA thinks that the tunnel is still up and running. Here is the configuration of the tunnel. Toronto (1.1.1.1) crypto map Outside_map 1 match address Outside_cryptomap crypto map Outside_map 1 set peer 3.3.3.3 crypto map Outside_map 1 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_3.3.3.3 internal group-policy GroupPolicy_3.3.3.3 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 3.3.3.3 type ipsec-l2l tunnel-group 3.3.3.3 general-attributes default-group-policy GroupPolicy_3.3.3.3 tunnel-group 3.3.3.3 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** San Francisco (3.3.3.3) crypto map Outside_map0 2 match address Outside_cryptomap_1 crypto map Outside_map0 2 set peer 1.1.1.1 crypto map Outside_map0 2 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map0 2 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_1.1.1.1 internal group-policy GroupPolicy_1.1.1.1 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 general-attributes default-group-policy GroupPolicy_1.1.1.1 tunnel-group 1.1.1.1 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** I'm at a loss. Any ideas?

  Read the article

• Offline cache copies in Windows file sharing

  - by netvope

  I frequently access media files (music or video) on a remote Windows file share. My Internet connection is not very fast, and I find it a waste of bandwidth when I repeatedly access the same files. For example, I may listen to the same song 30 times in a month. So, I would like to cache files I've used. I know Windows has an "Always available offline" feature but I dont' think it suit my needs. I don't want to make the whole share "available offline" as the remote Windows file share is huge (in terabytes). Making individual files "available offline" is tedious as the files are scattered in many different directories. It would be much more convenient if the system can simply cache those I've used. I could also manually make a local copy each time I use a file... but this is even more troublesome than making each file "available offline" Also The files on the share seldom change. Many of the files are rarely used. Some of the files are frequently used. I don't have a list of the most frequently used files. It would be the best if I could tell Windows to cache the last accessed 10GB, but apparently it doesn't have this feature. So I think the best way is to have a SMB/CIFS caching proxy. What do you think? I have a Linux box sitting around. Perhaps I should try to setup samba4?

  Read the article

• Mercurial internal Setup on Windows 7 - Exception happened during processing of request from ...

  - by Sad0w1nL1ght

  Hy, i have 1 central repository and many locals. On my machine i have local and a central repository too. I can make clone/commit/update/push/pull very easy between the local and central repository on my local machine. but when i want to make a clone from another machine it gets an error. listening at http://MyLocalMachine:8000/ (bound to *:8000) ---------------------------------------- Exception happened during processing of request from ('192.168.0.194', 49319) Traceback (most recent call last): File "SocketServer.pyc", line 558, in process_request_thread File "SocketServer.pyc", line 320, in finish_request File "mercurial\hgweb\server.pyc", line 47, in __init__ File "SocketServer.pyc", line 615, in __init__ File "BaseHTTPServer.pyc", line 329, in handle File "BaseHTTPServer.pyc", line 323, in handle_one_request File "mercurial\hgweb\server.pyc", line 79, in do_GET File "mercurial\hgweb\server.pyc", line 70, in do_POST File "mercurial\hgweb\server.pyc", line 63, in do_write File "mercurial\hgweb\server.pyc", line 127, in do_hgweb File "mercurial\hgweb\hgweb_mod.pyc", line 86, in __call__ File "mercurial\hgweb\hgweb_mod.pyc", line 118, in run_wsgi ErrorResponse ---------------------------------------- The command line wich started the central repo: hg serve -R TT -n TTZoli The command from remote machine for cloning: hg clone --pull http://MyLocalMachine:8000/TT Config for the central repo: [ui] username = MyLocalUserName username = test <[email protected]> with this user i'm trying to acces the central repo [web] push_ssl = false Config for the remote repo: [ui] username = test <[email protected]> [web] push_ssl = false I'm not sure if it's relevant,my firewall is turned off on both machines, and the files in /hg folder are not versioned on the server, except hgignore. Could you please suggest some ideas? What could be the problem? Thanks in advance!

  Read the article

• Multicast hostname lookups on OSX

  - by KARASZI István

  I have a problem with hostname lookups on my OSX computer. According to Apple's HK3473 document it says for v10.6: Host names that contain only one label in addition to local, for example "My-Computer.local", are resolved using Multicast DNS (Bonjour) by default. Host names that contain two or more labels in addition to local, for example "server.domain.local", are resolved using a DNS server by default. Which is not true as my testing. If I try to open a connection on my local computer to a remote port: telnet example.domain.local 22 then it will lookup the IP address with multicast DNS next to the A and AAAA lookups. This causes a two seconds lookup timeout on every lookup. Which is a lot! When I try with IPv4 only then it won't use the multicast queries to fetch the remote address just the simple A queries. telnet -4 example.domain.local 22 When I try with IPv6 only: telnet -6 example.domain.local 22 then it will lookup with multicast DNS and AAAA again, and the 2 seconds timeout delay occurs again. I've tried to create a resolver entry to my /etc/resolver/domain.local, and /etc/resolver/local.1, but none of them was working. Is there any way to disable this multicast lookups for the "two or more label addition to local" domains, or simply disable it for the selected subdomain (domain.local)? Thank you!

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• OpenWRT + OpenVPN client forwarding from lan to vpn not working

  - by Dariusz Górecki

  I've OpenWRT router with Backfire 10.03.1-rc3 (arch:brcm 2.6 kernel) I've set up an OpenVPN client connecting my router with workplace lan, and it works nicely, I can connect from router to networks (several) in workplace. My OpenVPN client uci-config looks like: config 'openvpn' 'stream_client' option 'nobind' '1' option 'float' '1' option 'client' '1' option 'reneg_sec' '0' option 'management' '127.0.0.1 31194' option 'explicit_exit_notify' '1' option 'verb' '3' option 'persist_tun' '1' option 'persist_key' '1' list 'remote' 'remote.address.cutted' option 'ca' '/lib/uci/upload/cbid.openvpn.stream_client.ca' option 'key' '/lib/uci/upload/cbid.openvpn.stream_client.key' option 'cert' '/lib/uci/upload/cbid.openvpn.stream_client.cert' option 'enable' '1' option 'dev' 'tun1' I've set the 'STREAM_VPN' Zone to allow in/out traffic, and I've added rules for zone-to-zone lan<-vpn and vpn<-lan config 'zone' option 'name' 'stream_vpn' option 'network' 'stream_vpn' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'forwarding' option 'src' 'lan' option 'dest' 'stream_vpn' config 'forwarding' option 'src' 'stream_vpn' option 'dest' 'lan' And interface config: config 'interface' 'stream_vpn' option 'proto' 'none' option 'ifname' 'tun1' option 'defaultroute' '0' option 'peerdns' '0' Now, from my router everything works nicely, the problem is that I cannot connect from computer inside a lan to hosts in networks provided by vpn connection :/ What I've missed, or what I'm doing wrong? And how can I force using specified DNS when connected to vpn? (I know that sever should use PUSH DNS option, but is PUSHes only routes)

  Read the article

• LDAP, Active Directory and bears, oh my!

  - by Tim Post

  What I have: Workstations running Ubuntu Jaunty mounting /home on a remote NFS server. User accounts are still created locally on each individual workstation. Workstations running Windows XP / Vista NFS server (as noted above) Windows 2008 server All machines share a single private network (LAN). What I need to accomplish: A single, intuitive (GUI driven) place for an office administrator to create user accounts. This should let anyone login to their (linux or windows) workstation, then fire up remote desktop and use the same login to the Windows 2008 server, from any machine on the network. I have read so much on samba, LDAP vs AD, etc and now I'm even more confused than I was before I began researching the problem. Ideally, Linux and Windows users should be able to get to their local files once logged into the Win2008 server. I am a programmer, not an interoperability guru and I'm completely lost on where to even start trying to accomplish this, plus I've run out of things to Google. How would you do this? Is it even possible?

  Read the article

• FTP not listing directory NcFTP PASV

  - by Jacob Talbot

  I am attempting to setup Multicraft on my server, all is running smoothly however the FTP won't allow anyone to connect from a remote FTP client, where net2ftp will work smoothly from a remote location. I have included the transcript from my FTP client, Transmit below to give you an idea of what's going on. I have disabled iptables as well, and still no luck either way. Transmit 4.1.7 (x86_64) Session Transcript [Version 10.8.2 (Build 12C54)] (21/10/12 11:23 PM) LibNcFTP 3.2.3 (July 23, 2009) compiled for UNIX 220: Multicraft 1.7.1 FTP server Connected to ateam.bn-mc.net. Cmd: USER jacob.9 331: Username ok, send password. Cmd: PASS xxxxxxxx 230: Login successful Cmd: TYPE A 200: Type set to: ASCII. Logged in to ateam.bn-mc.net as jacob.9. Cmd: SYST 215: UNIX Type: L8 Cmd: FEAT 211: Features supported: EPRT EPSV MDTM MLSD MLST type*;perm*;size*;modify*;unique*;unix.mode;unix.uid;unix.gid; REST STREAM SIZE TVFS UTF8 End FEAT. Cmd: OPTS UTF8 ON 200: OK Cmd: PWD 257: "/" is the current directory. Cmd: PASV Could not read reply from control connection -- timed out. (SReadline 1)

  Read the article

• How to remove static IP from Mitel 5312 and enable DHCP

  - by jimbo

  I'm not sure this is the right forum for this question -- although I'm confident I'll be told if not! -- but I've read the fine manual (at least, such a manual as I have), I've googled and I cannot get any insight into where to even start solving this problem. I have a bunch of Mitel 5312 handsets, talking to a 3300 ICP controller. Some handsets are at a remote location, get an address from my DHCP server over there, and use the Mitel "Teleworker" extension to connect in over the Internet. The remaining handsets were set up with static IPs by a BT-supplied engineer, on the same subnet as the ICP itself. So far, so good. I have one remaining teleworker licence, and need to move a handset from the home location to the remote. I've managed to boot it and configure teleworker, but I cannot for the life of me see where I tell it to forget its static IP, and make a DHCP request. Any ideas? Should I be looking on the controller, or holding magic combinations of buttons on the handset itself? EDIT: Following some advice from Robert, below, I've broken out a spare device and reassigned the profile for this user's extension to the MAC of the new phone, and a new profile to the old MAC. Unfortunately this still doesn't get me anywhere -- the new handset now asks for the teleworker install password. I suspect I'm going to have to get a Mitel engineer involved here, since I've never been given that password... Unless anyone has any great ideas?

  Read the article

• Keyboard issue when using kitty+puttycyg but not when using putty or cygwin alone

  - by kamaradclimber

  I would like to use a unique way to use console on my windows setup. Previously I used putty for remote access to linux servers and cygwin to have unix-like tools on windows. Then I discovered kitty which is a patched putty and have added the puttycyg patch. It provides the same way to connect to remote and local console. However, there is a strange behavior using vim when connected to the local console (using the puttycyg patch) : keys display A/B/C/D and replace the current character by these letter. In insert mode it does replace the caracter, in normal mode, no modification is made to the document even if the caracter is displayed as replaced. For instance, when I type : fixed bug with product deleted I get : fixed bbug wiwith prprodudueleteted I have read a lot of questions about this type of issue 3, 4 and googled it but there is no answer that work for me. The issue is present only for the setup kitty+puttycyg patch : cygwin alone works perfectly (and putty alone works also for access to linux servers). Any help would be appreciated !

  Read the article

• Connecting remotely to an SQL server inside a LAN

  - by vondip

  Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

  Read the article

• The Network folder specified is currently mapped using a different user name and password

  - by Frank Thornton

  I have a NAS device, it has 3 shares. On one computer I have access to all 3 of the shares. On another computer I keep getting this error when try and add a 2nd one. The Network folder specified is currently mapped using a different user name and password [...] That is the message I keep getting. What causes that? EDIT: Every share has it's own username and password. EDIT: NET USE on the one running 3 from the same NAS device New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK T: \\192.168.2.5\SHARE1 Microsoft Windows Network OK X: \\Nas-1dsho-abc\SHARE2 Microsoft Windows Network Disconnected Y: \\192.168.2.9\backups Microsoft Windows Network OK Z: \\Nas-1dsho-abc\cbackups Microsoft Windows Network The command completed successfully. NET USE on the other: New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK Y: \\192.168.2.5\SHARE1 Microsoft Windows Network Unavailable Z: \\192.168.2.5\SHARE2 Microsoft Windows Network The command completed successfully.

  Read the article

• Trouble getting latest version of Git

  - by TheMethod

  I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

  Read the article

• Cluster FIle System

  - by Ben

  We are looking for to choose a clustered file system for our in house appplication. Let me first highlight my requirement. we have a storage and 2 servers at present.We get the data files from remote servers to our server and on both servers we are running our application to access those data and make a final result as per our requirements. In future may be after 3-4 months, we can add another servers in current cluster pool to handle more data load from remote location data senders. So my requirement is that to integrate same storage partition on 2-3 servers , it might be 4-5 more servers in future, My application read data from storage partition and write back to storage partition. Is there any bottleneck / limitation from RHCS , GFS2 or anything.? We are new with RHCS + GFS and all. Can we have any other better approach or someway to deal with our requirement light way? what is the best OS version for this ? how's RHEL 6.4 64 bit ? please share some case study or some gudie reference as per past experiences with such environnmnets Regards, Ben

  Read the article

• Completely remove and freshly install MySql on XP?

  - by Corey Ogburn

  I have read this question and have not found it as a solution and I have even attempted much more. I've uninstalled MySql 5.5.18 and deleted: C:\Program Files\MySql C:\Documents and Settings\All Users\Application Data\MySql After uninstalling, I restart the computer. When I reinstall, in the MySql Server Instance Configuration Wizard I leave everything to their defaults except: I add a firewall exception I check Launch MySQL Server Automatically I check Include BIN directory in windows path Enable root access from remote machines (I'll lock that down later, just debugging for now, I have also tried installing without this option to no avail) I've tried Typical and Complete while installing, as well as with and without strict mode. No combination shows a difference. After all this, it cannot Apply Security Settings and I get a 10061 error (it also said error number 2003) and this article didn't help. I've tried everything I can to completely uninstall and successfully reinstall so I can start from scratch. I've uninstalled and reinstalled about a dozen times with minor changes (including turning off the firewall at times), each time deleting the above folders and any proper registry entries with no success. Note by success, applying security settings and a working remote connection. I can connect locally every time, but it's remotely that counts. I have tried to look for exterior problems such as port forwarding in the router and (even though the installer should add it) I do double check the firewall settings, which have always allowed the default port. I'm out of ideas.

  Read the article

• Can't connect to EC2 instance Permission denied (publickey)

  - by Assad Ullah

  I got this when I tried to connect my new instace (UBUNTU 12.01 EC2) with my newly generated key sh-3.2# ssh ec2-user@**** -v ****.pem OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to **** [****] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /var/root/.ssh/id_rsa type -1 debug1: identity file /var/root/.ssh/id_rsa-cert type -1 debug1: identity file /var/root/.ssh/id_dsa type -1 debug1: identity file /var/root/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '****' is known and matches the RSA host key. debug1: Found key in /var/root/.ssh/known_hosts:4 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /var/root/.ssh/id_rsa debug1: Trying private key: /var/root/.ssh/id_dsa debug1: No more authentication methods to try.

  Read the article

• DRBD Replication failure

  - by user62513

  A couple of weeks ago I setup a 2 nodes CRM system with one of the resources managed being MySQL over DRBD. Today for maintenance reasons I restarted both nodes but now they can't connect to each other anymore. DRBD fell out of sync and I followed this guide to get it back connected but it's only able to run successfully on one node. But this strange thing happens: If I crm node standby both nodes and I try: crm node online node0 before crm node online node1, all the CRM resources start successfully but the DRBD partitions are still running in StandAlone state. crm node online node1 beofre crm node online node0, the DRBD resource fails to start, thus causing mysql not to start. If I standby both resources and call crm node online node0 then it times out and prints this error: Running crm node online node0 produces this output after timing out Error setting standby=off (section=nodes, set=<null>): Remote node did not respond Error performing operation: Remote node did not respond Is there anything I'm doing wrong here? An alternative will be just do MySQL replication but I'm not sure how to promote a slave to master when the master database is not available.

  Read the article

• Understanding encryption Keys

  - by claws

  Hello, I'm really embarrassed to ask this question but its the fact that I don't know anything about encryption. I always avoided it. I don't understand the concept of encryption keys (public key, private key, RSA key, DSA key, PGP Key, SSH key & what not) . I did encounter these in regular basis but as I said I always avoided them. Here are few instances where I encountered: Creating Account: A public RSA or DSA key will be needed for an account. Send the key along with your desired account name to [email protected] I really don't know what are RSA/DSA or How to get their keys? Do I need to register some where for that? Mailing: I'm unable to recall exactly but I've seen some mails have some attachments like signature or the mail footer will have something called PGP signature etc.. I really don't get its concept. GIT Version control: I created account in assembla.com (for private GIT repo) and it asked me to enter "SSH keys" to my profile. Where am I gonna get these? Why do I need it? Isn't SSH related to remote login (like remote desktop or telnet)? How are these two SSHs related & differ? I don't know in how many more situations I'm going to encounter these things. I'm really confused and have no clue about where to start & how to proceed to learn these things. Kindly someone point me in correct direction. Note: I've absolutely zero interested in encryption related topics. So, there is no way I'm going to read a graduate level book on this subject. I just want to clear my concepts without going into much depth.

  Read the article

• SNMP Access on Ubuntu

  - by javano

  I am trying to use SNMP to monitor a machine locally on its self and remotely. This is the snmpd.conf (Ubuntu 8.04.1): # sec.name source comunity com2sec readonly 1.2.3.4 nicenandtight com2sec readonly 5.6.7.8 reallysafe group MyROGroup v1 readonly group MyROGroup v2c readonly group MyROGroup usm readonly view all included .1 view system included .iso.org.dod.internet.mgmt.mib-2.system access MyROGroup "" any noauth exact all none none syslocation my house syscontact me <[email protected]> exec .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro smuxpeer .1.3.6.1.4.1.674.10892.1 includeAllDisks 95% 1.2.3.4 is the local machines IP and everything is working locally. 5.6.7.8 is the remote machine and initially I am just trying to touch SNMPD with snmpwalk from the remote machine; snmpwalk -v 2c -c reallysafe 1.2.3.4 Timeout: No Response from 1.2.3.4 I have added to iptables as the very first rule; -A INPUT -p udp -m udp --dport 161 -j ACCEPT With such a loose iptables rule I can't see why I can't even touch the SNMPD on that Uubuntu Machine. There are more specific rules further down the table but as I couldn't connect I added the above. TCPDump shows the UDP packets coming in. What could be going wrong here?

  Read the article

• can't ssh from mac to windows (running ssh server on cygwin)

  - by Denise

  I set up an ssh server on a fresh windows 7 machine using the latest version of cygwin. Disabled the firewall. I can ssh into it from itself, from a different windows box (using winssh), and from a linux vm. In spite of that, I tried to ssh in from two different macs, and neither would let me! This is the debug output: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 3dbuild [172.18.4.219] port 22. debug1: Connection established. debug1: identity file /Users/Denise/.ssh/identity type -1 debug1: identity file /Users/Denise/.ssh/id_rsa type 1 debug1: identity file /Users/Denise/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5 debug1: match: OpenSSH_5.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '3dbuild' is known and matches the RSA host key. debug1: Found key in /Users/Denise/.ssh/known_hosts:43 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /Users/Denise/.ssh/identity debug1: Offering public key: /Users/Denise/.ssh/id_rsa Connection closed by [ip] It shows the same output, and fails at the same place, whether I have put my public key on the ssh server or not. Any help would be appreciated-- hopefully someone has run into this before?

  Read the article

• Nagios check_host_alive and check_ping not showing host as down

  - by Kyle

  I am using the check_host_alive command to send 5 packets every minute to all my routers at remote locations. I noticed today I received a notification from The AT&T Global Client Support Center that a router was down (which can take 5-30 minutes to send these notices out) and never received a notice from Nagios. I went onto Nagios and it is was showing the host as alive with a latency of 0ms. This tells me it is seeing the automated response from my router in the data center that, "TTL expired in transit" as a reply from the remote router. Is there anyway for me to tell nagios to check where the reply is comming from? I feel like other people have to of had this issue... I tested it with the check_ping command and it produced the same results. I have the command defined has %hostname% and the proper IP in the host definition, and it works fine for telling me the latency is high. Any ideas are welcome, I have already exercised my Google skills with no results. EDIT: root@IM-UBTU:/# /usr/local/nagios/libexec/check_ping -H 192.168.250.1 -w 100.0,10% -c 200.0,20% -vvv CMD: /bin/ping -n -U -w 10 -c 5 192.168.250.1 Output: PING 192.168.250.1 (192.168.250.1) 56(84) bytes of data. Output: From 10.69.10.2 icmp_seq=1 Time to live exceeded It knows something is wrong why doesn't it give me a warning?

  Read the article

• After upgrading to 2008 R2 Enterprise and installing more RAM, Windows can only see 4.00 GB

  - by Tom Crane

  (I have also posted this on technet but I'm running out of ideas) I've upgraded from Windows Server 2008 R2 Standard to Enterprise in order to make use of more RAM. The server previously had 32GB of RAM. The upgrade from Standard to Enterprise, using DISM, seemed to go OK, so I powered down and installed the RAM. This a Dell Poweredge T710, I was taking it from 32GB to 72GB. The BIOS recognised the RAM, although I needed to change from "Advanced ECC" to "Optimizer" mode for it to use all of it. After rebooting, windows can see the RAM but in the system panel will display: Installed memory (RAM): 72.0 GB (4.00 GB usable) In the resource monitor, the remainder of the RAM is showing as reserved for hardware. I've tried various RAM configurations, including reverting it to the same chips and same configuration as before the upgrade, but always just 4.00 GB is showing up as usable. Following some threads on these forums I've gone into msconfig and set the maximum memory "by hand" but that doesn't fix the problem. BIOS doesn't seem to have anything that looks like memory remapping which is another suggestion that has come up. How do I make this RAM available to Windows? It was available before the upgrade, because I could use the full 32GB RAM the server had to start with. A screenshot (this is after reverting to the original RAM configuration) http://screencast.com/t/5FuzevdNb I don't know if it's related, but my remote desktop configuration has also disappeared: screencast.com/t/mYedomeQWS (the bottom half of this dialog should allow me to configure Remote Desktop, it was working before the upgrade but now it isn't).

  Read the article

• IP6 seems to be enabled - How do I configure it without interfering with IP4?

  - by Mister IT Guru

  I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

  Read the article

• GVIM hangs when saving through GVFS' FTP

  - by Lie Ryan

  I loved Gnome's Nautilus and FTP integration and being able to mount a remote FTP directory as a regular bookmark/directory, and double clicking any remote files to open in any unmodified program. I also loved editing text files with GVim. However, if I double clicked file on Nautilus to open a text file in Gvim, then saving a file will take about 10 seconds and GVim will hang for that amount of time. The major irritant is that I cannot continue editing while the text editor is waiting for the write to finish, this delay interrupted my workflow and thought process and saving becomes a painful process. The other problem is that I don't think simply uploading a file should take that much time. I'm aware of GVim's internal FTP support, but they are not as well integrated with Nautilus's FTP. So a few question: Is there a way to make GVim or GVFS to save in background while I continue editing? Why is GVFS so slow? Is there any way to set GVFS to use a single persistent FTP connection instead of creating a new FTP connection each time? I'm on Gentoo Linux x86-64.

  Read the article

• Looking for a small, portable, port-mirroring ethernet switch.

  - by user37244

  I recently had a mac go haywire, taking half a minute or more to get www.google.com loaded. Getting its owner to give up the machine for repair was like pulling teeth - they were insisting that it must be something to do with the network, since so much had changed with the local configuration at about the same time their box went haywire. I eventually set up a port mirror to a box that I could remote to so I could show that the mac was only irregularly getting packets onto the network. Demonstrating this faced an additional challenge: the latency of the remote desktop software I was using meant that I had to point to timestamps instead of just the moment the packet flashed up on the screen as my evidence. This particular user was the reason this was so challenging this time around, but I would like to have a box that I can cart from desk to desk to use wireshark on my laptop at any station where I need it. 3com, cisco, netgear, etc. (ad nauseum), all make switches that can be configured for port mirroring, but in my case, the smaller, the better. For the sake of my sanity, I'll probably end up running it off a battery anyway. If my laptop had two ethernet ports, this would be easy. So, whaddya recommand for a device that requires 0 configuration at each powerup (though I'm fine with poking at it for a while to set it up initially.) Small, light, and cheap enough to get it past purchasing? Thanks,

  Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >