Search Results

Search found 30658 results on 1227 pages for 'off screen'.

Page 391/1227 | < Previous Page | 387 388 389 390 391 392 393 394 395 396 397 398  | Next Page >

• xrandr fails when 3rd monitor has higher resolution

  - by Pi3cH

  I tried many combinations with xrandr command under lubuntu 12.04 to setup my three monitors DVI (DELL 1) left detected as HDMI1 HDMI (LG E2290) middle detected as HDMI2 VGA (DELL 2) right detected as VGA1 I can get the display with fix 1280x1024 on all the monitors. But once I setup 1280x1024 + 1920x1080 + 1280x1024, I get blank screen on all the monitors. Sometimes it throws crts fail error instead of blanking out. Anyone have similar issues? any solutions/workarounds? P.S. I can setup two monitors using 1280x1280 and 1920x1080 P.S.S. HDMI2 required at least 1920x1080 to display sharp picture. Outputs (it seems graphic card supports up to 8192x8192): xrandr Screen 0: minimum 320 x 200, current 3840 x 1024, maximum 8192 x 8192 VGA1 connected 1280x1024+2560+0 (normal left inverted right x axis y axis) 338mm x 270mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI1 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI2 connected 1280x1024+1280+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0 + 1680x1050 60.0 1280x1024 75.0 60.0* 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) 3 CRTs (0,1 VGA, 0,1,2 for other HDMI) xrandr --verbose VGA1 connected 1280x1024+2560+0 (0x47) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x42 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 ... HDMI1 connected 1280x1024+0+0 (0x47) normal (normal left inverted right x axis y axis) 376mm x 301mm Identifier: 0x43 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 0 1 2 ... HDMI2 connected 1280x1024+1280+0 (0x47) normal (normal left inverted right x axis y axis) 477mm x 268mm Identifier: 0x44 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 2 CRTCs: 0 1 2 Below command fails: xrandr --output VGA1 --auto --output HDMI2 --auto --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Below command passes: xrandr --output VGA1 --auto --output HDMI2 --mode 1280x1024 --rate 60.0 --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Graphic card VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09)

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• 100% uptime for a web application

  - by Chris Lively

  We received an interesting "requirement" from a client today. They want 100% uptime with off-site failover on a web application. From our web application's viewpoint, this isn't an issue. It was designed to be able to scale out across multiple database servers, etc. However, from a networking issue I just can't seem to figure out how to make it work. In a nutshell, the application will live on servers within the client's network. It is accessed by both internal and external people. They want us to maintain an off-site copy of the system that in the event of a serious failure at their premises would immediately pick up and take over. Now we know there is absolutely no way to resolve it for internal people (carrier pigeon?), but they want the external users to not even notice. Quite frankly, I haven't the foggiest idea of how this might be possible. It seems that if they lose Internet connectivity then we would have to do a DNS change to forward traffic to the external machines... Which, of course, takes time. Ideas? UPDATE I had a discussion with the client today and they clarified on the issue. They stuck by the 100% number, saying the application should stay active even in the event of a flood. However, that requirement only kicks in if we host it for them. They said they would handle the uptime requirement if the application lives entirely on their servers. You can guess my response.

  Read the article

• computer fails to boot during/after POST for five or six boots, then works

  - by N13

  For the last few days, my computer has had issues booting. I've seen two different behaviors: The screen displays the graphics card information, then begins to list the RAM, hard drives, etc. At different points in this process (after the graphics info), the computer shuts off. After five or six attempts, it then boots normally. In roughly the same time frame, the computer freezes, and fails to boot. I think it boots successfully on the next attempt. I've also noticed that in some instances, the computer freezes on shutdown. It gets right to the point where it should shut off, but doesn't. I recently combined the best parts of two different machines into this one. I'm booting to GRUB, with Ubuntu 12.04, Linux Mint 11 and Windows Vista (unfortunately) as my OS options. It has an Enermax Modu82+ 525W power supply, and I've used an online calculator to determine that my load shouldn't exceed 400W. I even unplugged a hard drive, but that didn't help. I found the latest BIOS, patched it and checked the settings, but that didn't fix it. I'm fairly certain this issue didn't exist at first, but might have started when the power at my new apartment dropped for a second. The machine is plugged into a surge protector strip, but it's old and I've heard they lose effectiveness with age. Is a power dip as damaging as a spike? If something were damaged, why would it boot successfully after five or six attempts? It's almost like the BIOS or PSU need to be primed. The trouble with debugging is that there seems to be a "grace period" after shutdown where the issue doesn't present itself again. What should I try next?

  Read the article

• DRBD as a block device for XEN VM (Centos 5.3)

  - by SaberTooth

  Hi all, I have setup a drbd resource between 2 server nodes - everything works correctly when doing sync tests between the two. (I want to create a HA cluster using drbd,xen and heartbeat) However, when I try and create a XEN VM with Centos as guest operating system, I get through to the partitioning screen on the install but when I select a partitioning type the next screen gives me the following error : "An error has occurred - no valid devices were found on which to create new file systems. Please check your hardware for the cause of this problem." This is the first time attempting create a setup like this and searching Google does not help much... my config files for DRBD and XEN.... DRBD (just the section that is pertinent) on xennode0 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; flexible-meta-disk internal; } on xennode1 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; meta-disk internal; } XEN kernel = "/boot/xeninstall/vmlinuz" ramdisk = "/boot/xeninstall/initrd.img" extra = "text" name = "VM" maxmem = 3000 memory = 3000 vcpus = 4 on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ ] disk = [ "phy:/dev/drbd0,sda1,w", "tap:aio:/srv/xen/xenswap.img,sda2,w" ] vif = [ "mac=00:16:3e:11:67:ae,bridge=xenbr0" ] root = "/dev/sda1 ro" Thanks in advance!

  Read the article

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• Ubuntu on VPS becomes unresponsive: BUG: soft lockup - CPU#0 stuck for 22s

  - by Bhante Nandiya

  We have a VPS running Ubuntu, on Xen. The problem is this, about once a day, for about 20-50 minutes, at a random time, the server becomes completely unresponsive to the outside world. After this period, it becomes responsive again, as if nothing had happened, it doesn't lose uptime, it doesn't restart. It just starts responding again as if it had been in suspended animation. These outages occur under conditions of non-exceptional memory and cpu, for example 70% mem, 5% cpu. I have stopped all non-essential services so the usage is very even. These outages don't particularly occur during times of increased memory/cpu (during daily tasks), they sometimes occur at times of very low cpu use (<2%), but in the past also occured during swapping. These blackouts have been occurring both under Ubuntu 12.04 LTS, and Ubuntu 14.04 LTS - no change at all (I upgraded Ubuntu specifically to see if it helped this problem). It is possible to log into our webhosts site, and use their administration console to see error messages from during this time. Presumably, these messages are from the Xen virtualization, the main message goes like this: BUG: soft lockp - CPU#0 stuck for 22s! [ksoftireqd/0:3] (repeats many times) SysRq : Emergency Sync (Sometimes this is the only message in the console) Others seen previously under different load situations include: BUG: soft lockup - CPU#0 stuck for 22s! [swapper/0:0] (repeated many times) or: INFO: rcu_sched detected stall on CPU 0 (t=15000 jiffies) (repeated many times with t getting bigger) From googling around I've tried various kernel parameters such as nohz=off and acpi=off to no avail. All tech support has said is that other Ubuntu installations are not suffering the same problem. Anyone got any ideas or experience with this problem?

  Read the article

• NVidia TwinView - slow rendering on dual desktop [closed]

  - by lisak

  Hey, does anybody have experience with it ? I've set it up 4 times on 4 different machines. And there was always problems with slow rendering ( for instance : scrolling pages in browser is not fluent). But there always was something that finally made it work perfectly... I remember that one time this option helped, but not now Option "RenderAccel" "1" Nvidia geforce 8400GS or Zotac geforce 9500GT Monitors connected via dvi and hdmi connectors proper nvidia driver installed Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "0" EndSection Section "Files" ModulePath "/usr/lib64/xorg/modules" FontPath "/usr/share/fonts/local" FontPath "/usr/share/fonts/TTF" FontPath "/usr/share/fonts/OTF" FontPath "/usr/share/fonts/Type1" FontPath "/usr/share/fonts/misc" FontPath "/usr/share/fonts/CID" FontPath "/usr/share/fonts/75dpi/:unscaled" FontPath "/usr/share/fonts/100dpi/:unscaled" FontPath "/usr/share/fonts/75dpi" FontPath "/usr/share/fonts/100dpi" FontPath "/usr/share/fonts/cyrillic" EndSection Section "Module" Load "dri2" Load "glx" Load "extmod" Load "record" Load "dbe" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Acer AL1715" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 75.0 EndSection Section "Device" Identifier "Nvidia" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "MSI big bang-fuzion" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 8400 GS" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "RenderAccel" "1" Option "AllowGLXWithComposite" "1" Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "CRT: 1280x1024 +1920+0, DFP: 1920x1080 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Computer making strange sound when turned on, ever since power outage

  - by Dot NET

  Recently we experienced a power outage, and the PC was off. However, once the power came back, I switched on the PC and heard a strange noise - almost as if the hard disk or fans were struggling to work. I can't really describe the sound, but it's a laboured, loud sound almost like a jack-hammer. This has been persisting ever since the power outage, however the noise stops after around 10 minutes or so, and doesn't start again until the computer is turned off and on again. At first I thought it had something to do with the HDD, but all my files are intact, chkdsk did not report any issues and performance is 100% unchanged, even in games (so the gfx card is fine, and so is the HDD most likely). My PC setup basically has around 3 cooling fans, but I'm not sure if it's one of these either as the noise actually stops after 10 minutes or so, and if I leave the PC on for 4 hours (for example) the noise never starts again. It's there solely when turning on the PC. I haven't got a UPS, and it's important to note that the computer was not on when the power went out - it was merely plugged in. I then promptly unplugged the PC once the power was out, and only plugged it in again when the power came back. Could it be the power supply? Unfortunately I can't open my tower as I would void the warranty. Are there any tests which I could carry out without voiding the warranty?

  Read the article

• How to I configure open_basedir parameter under my Centos VPS?

  - by deltanovember

  The parameter can be seen here http://wordswithfriends.net/test.php open_basedir /var/www/vhosts/wor.wordswithfriends.net/wordswithfriends.net/:/tmp I'm trying to add PHP pear directories /var/www/vhosts/wor.wordswithfriends.net/conf is as follows -rw-r----- 1 root apache 6461 Jan 25 08:56 12959674170.16899500_httpd.include -rw-r----- 1 root apache 6461 Jan 31 06:52 12960111810.31860800_httpd.include -rw-r----- 1 root apache 6532 Jan 31 06:55 12964785250.54523600_httpd.include -rw-r----- 1 root apache 6532 Jan 31 07:01 12964788880.47252600_httpd.include -rw-r----- 1 root apache 6532 Jan 31 15:54 12965108850.92819600_httpd.include -rw-r----- 1 root apache 6652 Jan 31 21:32 12965206700.32285200_httpd.include Currently configured as follows grep base 12965206700.32285200_httpd.include php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ Configured vhost.conf as follows <Directory /var/www/vhosts/wor.wordswithfriends.net/wordswithfriends.net> <IfModule sapi_apache2.c> php_admin_flag engine on php_admin_flag safe_mode off php_admin_value open_basedir "/var/www/vhosts/wor.wordswithfriends.net:/tmp:/usr/share/pear/local/PEAR" </IfModule> <IfModule mod_php5.c> php_admin_flag engine on php_admin_flag safe_mode off php_admin_value open_basedir "/var/www/vhosts/wor.wordswithfriends.net:/tmp:/usr/share/pear:/local/PEAR" </IfModule> </Directory> Restarted apache and the parameter is still the same. I'm not sure why my pear directories are not showing up. I'm using Plesk. Any help appreciated

  Read the article

• AutoHotKey temporarily rebind Winkey

  - by wes

  I've got a wireless keyboard that puts some media keys on top of the Function keys, so that by default F4 is actually lock (Rwin & l) and Fn+F4 is a real F4. So I'd like to basically switch those around. Here's what the key history shows: VK SC Type Up/Dn Elapsed Key ------------------------------------- 73 03E d 17.32 F4 ; Fn+F4 73 03E u 0.16 F4 5C 15C d 2.96 Right Windows ; F4 4C 026 d 0.00 L 5C 15C u 0.13 Right Windows 4C 026 u 0.00 L This doesn't do anything: SC15C & SC026::MsgBox,Pressed F4 But this prints that I hit F4 then goes to the login screen: Rwin & l::MsgBox,Pressed F4 So how can I stop it from switching to the login screen? Ideally I'd like F4 (which registers as Rwin & l) to just send F4, Fn+F4 to send Rwin & l, and also have them work with other keys (e.g., a manual !F4 should still close a window). Is this possible?

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• Nginx load balancing and maintaining URLs

  - by Steve Klabnik

  I'm trying to use nginx as a load balancer, and it's working great. One problem, though. The load balancing box is at 123.123.123.123, and the backend box is 456.456.456.456. So I have this config: upstream backend { server 456.456.456.456; } server { listen 80; server_name 123.123.123.123; access_log off; error_log off; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://backend; } } This works great. I hit 123.123.123.123 in my browser, and the page comes up. But now the URL in the browser says http://456.456.456.456. Do I need to use a rewrite rule or something to keep the url correct? I don't want it to be different when going to different backed servers. None of the tutorials I've read have mentioned anything about this.

  Read the article

• Dell laptop keyboard doesn't work

  - by Tam

  I'm trying to fix my in-laws laptop, it's a Dell Studio 1745 that's running Windows 7 64 bit. The problem is that most of the keys on the keyboard do not work. The function keys work and the caps lock and numpad keys work, but no other keys do. If I hit the F2 key enough times when starting up, I can get to the BIOS, but after that even the function keys stop working. If I let it go all the way to the Windows login screen, I can see that the caps lock and num lock work - little images on screen actually appear, but they don't toggle the state of the key, i.e.,capslock is always off, numlock is always off. Using the fn+function combo works, so changing the brightness, etc. works fine. I'm stumped. I've tried disconnecting power and battery and leaving it for an hour or so before starting up but that hasn't helped either. Also - this might be a red herring - the touchpad is failing as well, the MS Device Manager says that it's failing with status 10, "unable to start device"

  Read the article

• System x3550 M2 stuck on system initializing after firmware upgrades

  - by itmanager223

  Hey guys so i have been having this major issue for the last few hours now. I have a system x 3550M2 server and i ran the UEFI and IMM firmware upgrades within windows server 2008 R2 x64. All upgrades went fine and i was told to reboot. I performed the reboot cleanly using the OS restart option. Upon restarting it showed the system initializing screen and it stayed there for a good hour. After that hour i figured it froze and so i powered down and power up again. Now i can not boot back up to even see the IBM splash screen or the OS... I have tried switching the Jumpers to go to the backup UEFI and backup IMM and no luck. I have also reset the CMOS power and i have pressed the reset button 3 times on the light path and no luck. There are no lights light on the light path to indicate anything is broken. The only thing i see on the light path is the number 0.5. Any ideas guys i am quite stumped with this problem. Thanks a lot, Dani Cela

  Read the article

• How to remotely connect using perfmon?

  - by user36914

  Suprised there is not a ton of information on google when i search for this but there is not. Lot of people asking the question but i none of them have any good answers. I have a remote computer running hyper-v (server) running a Windows 7 x64 guest (guest). Occasionally i won't be able to remote desktop to guest. I will then remote to server and see that the guest instance is constantly using about 25% of the cpu. WHen i try to connect directly from server i will get the login screen but as soon as i type the password in it will just stay at the windows 7 login screen but the account names will disappear and it will not log in. It responds to pings though. I don't know how else to diagnose other than trying to run perfmon remotely. It only happens like every 3 weeks and i run it 24/7. So i'm trying to run remote desktop remotely. I tested this out on a local vm i have running under vmware. When i try to connect using perfmon to my local vm i get this error: "when attempting to connect to the remote computer the4 following system error occurred: the network path was not found" I found in another past to start the remote registry service and when i start the service i get this error: "No such interface supported" Anyways, how do i remotely connect to another machine with perfmon or if anyone has a better idea how i can diagnose the problem above then let me know.

  Read the article

• Acer Aspire Touchscreen Not Responding

  - by Jerry

  I have an Acer Aspire z3101 all-in-one Touch screen running Windows 7 Home Premium. I am unable to get the screen to respond to my touch. I have checked the system and all drivers are ok according to comp. Using the settings to setup the pen and touch and to calibrate does not work. My touch brings no response at all. I had reinstalled the applications - Windows Touch Pack and Acer Touch Portal which didn't help. Today I done a complete reinstall returning comp back to factory settings and still there is no response. At first I thought that perhaps a driver or file was missing but now doubt that due to the reinstall not helping. Have you any idea what could be causing this problem? I am now at the stage of pulling my hair out and haven't had too much help from Acer. I have had the computer for just over a year now and so it is no longer under guarantee and this has me very worried due to my being unemployed. Any help is much appreciated. Thank you.

  Read the article

• Motherboard Dying? AHCI Drive Init and boot loop intermittent failure

  - by Adam Heath

  My computer is now intermittently failing to boot up. For the last couple of days, when I turn it on it hangs on "AHCI Drive Init...", and when powered off and on again, it booted up fine. Today, it did the same but failed in a few other ways too, seemingly at random: Hangs on "AHCI Drive Init..." Boot loop (after "AHCI Drive Init..." appears for a split second (no drives listed)) Black screen (after "AHCI Drive Init..." appears for a split second, a black screen with all fans still running) The interesting part is that the above is not affected by what drives are connected, or what to. I have tried both disks, each disk individually and no disks (along with trying the primary and secondary SATA controllers), none of this has any effect on what happens. After about 20+ attempts of different combinations, it suddenly decided it would boot up into Windows, and I hadn't touched anything for about 2 cycles. Motherboard: Gigabyte GA-870A-USB3 Processor: Amd Phoenom II x6 1090T RAM: 8GB Corsair 1600 Primary Disk: Plextor 128GB SSD Secondary Disk: Western Digital Black 1TB OS: Windows 8.1 Is this my motherboard dying? Or could something else be the cause? Thanks!

  Read the article

• Why is my new PC so slow at startup?

  - by rumtscho

  Bought a new PC this weekend, and it works really good. Only I have one big problem: startup time. Its BIOS needs 62 sec to load, then from Grub start to pw entering screen it's another 26 sec. I think this is a lot, because my old PC needs 34 sec for BIOS and another 8 sec to pw screen. After I enter the pw, the desktop is usable with practically no delay on both. The new PC is a core i7-930, running a Lucid Lynx 64 bit from a Intel Postville SSD (no internal HDs). The old PC is a Pentium 4 celeron (forgot the clock speed) running a Lucid Lynx 32 bit from an ATA 100 hard drive. Neither PC is overclocked. The new one has boot sequence 1.DVD ROM, 2.SSD (connected over SATA in AHCI mode), 3. removable drive. The old one boots from 1. DVD ROM, 2. HDD, 3. Floppy. Neither has a second OS installed. The new one has less software installed than the old one (I think), but the boot time difference was noticeable even before I made any installs. As far as I know, just the SSD should be enough to make a noticeable difference in boot time. I thought that having a good mainboard on the new PC as opposed to the basic office model on the old one would also mean a faster loading BIOS. If these assumptions are right, I guess I must have misconfigured something in the BIOS of the new PC. How should I configure it for a fast boot? It has an ASUS P6X58D board with an AMI BIOS, if you need the BIOS revision number I could post that too.

  Read the article

• Httpd and LDAP Authentication not working for sub-pages

  - by DavisTasar

  I just recently installed a Nagios implementation, and I'm trying to get LDAP authentication working for httpd on Red Hat. (nagios.conf for Apache config below, sanitized of course) ScriptAlias /nagios/cgi-bin "/usr/local/nagios/sbin" <Directory "/usr/local/nagios/sbin"> #SSLRequireSSL Options ExecCGI AllowOverride none AuthType Basic AuthName "LDAP Authentication" AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthzLDAPAuthoritative off AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Alias /nagios "/usr/local/nagios/share" <Directory /usr/local/nagios/share> #SSLRequireSSL Options None AllowOverride none AuthBasicProvider ldap AuthType Basic AuthName "LDAP Authentication" AuthzLDAPAuthoritative off AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Now, the initial authentication works, so when you first hit the page you can log in just fine. However, when you go anywhere else, it prompts you for authentication, fails (asking for a re-prompt), and gives this error message: [Mon Oct 21 14:46:23 2013] [error] [client 172.28.9.30] access to /nagios/cgi-bin/statusmap.cgi failed, reason: verification of user id '<myuseraccount>' not configured, referer: http://<nagiosserver>/nagios/side.php I'm almost certain its a simple flag or option, but I just can't find it, and I don't have a lot of experience working with Apache. Any assistance or help would be greatly appreciated.

  Read the article

• What to do with old laptop screens?

  - by Lord Torgamus

  This question is inspired by another SU question I came across earlier today: What to do with old hard drives? It made me think about two long-dead laptops I have with perfectly good screens still inside. One is a Dell Inspiron 5100 and the other is an Averatec E1200, but responses need not be geared towards those particular models' screens. Rules, based heavily on the original question's: Objectives and suggestions to keep in mind when you post an answer : Should showcase your geekiness, be plain ol' fun, serve a social purpose or benefit the community. Your answer need not be limited to only one screen. For a really good answer, I'll go out and buy additional leftover screens. Your answer need not be limited to one project per screen. If additional accessories need be purchased, make sure they are common. Don't tell me to get a moon rock or something. The projects you suggested should serve a useful purpose; art is nice, but functional art is way better. Thanks in advance, folks. EDIT: Found another related question. Fun projects to do with an old 17" LCD monitor EDIT 2: I, for one, am enjoying the new outpouring of creativity here. Best fifty bucks... I mean, rep points... I ever spent. EDIT 3: That does it. At the end of the week, there was a tie for most votes between the accepted answer and the game platform answer. The game platform answer was cooler, but less reasonable as a project to actually do; in other words, it was more moon rocky. Unfortunately, I think fencepost had the best comment on the topic, which is that displays on their own have no good interface. Thanks for playing, everyone!

  Read the article

• reverse proxying with NGINX to two back-end servers

  - by aag

  I am trying to learn how to configure the Nginx proxy. All requests from external (www.external.com) should go to internal server 10.10.10.16:2080, except for www.external.com/nagios requests, which should go to internal 10.10.10.18. My location block looks as follows: location ~* / { proxy_buffers 16 4k; proxy_buffer_size 2k; proxy_buffering off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Accept-Encoding ""; proxy_pass http://10.10.10.16:2080; } # # nagios server location ~* /nagios/ { proxy_buffers 16 4k; proxy_buffer_size 2k; proxy_buffering off; # proxy_set_header Host $host; # proxy_set_header X-Real-IP $remote_addr; # proxy_set_header Accept-Encoding ""; proxy_pass http://10.10.10.18; } The first location seems to work fine. However, any request to www.external.com/nagios sends the browser into the eternal pastures. Of course, 10.10.10.18/nagios was tested and works fine. What am I missing?

  Read the article

• lenovo x1 carbon windows 8 frequent wifi disconnect issue

  - by hIpPy

  I'm having frequent wifi disconnects on my Lenovo X1 Carbon Touch laptop. I got this laptop 2 months back and it has been happening ever since about 3-5 times a day and 10 times a week on average. I've Frontier Fios internet. Power connected or not does not matter. Once I get disconnected, I try below to connect again in that order: turn Airplane mode on and off, troubleshoot network problems windows troubleshooter), restart the laptop I'd find that the WiFi adapter would get disabled and sometimes windows troubleshooting would help but more than often I'd end up restarting the laptop. A week back, I upgraded my wifi network adapter drivers (now Intel, version 15.5.6.48, 10/3/2012). I still get disconnected frequently but turning Airplane mode on and off gets me connected again. So the driver update did help. Windows 8 is updated. None of the other devices (nexus, iphone phones, nexus7, ipad tablets) would have wifi issues when my laptop would get disconnected. config: Intel(R) Centrino(R) Advanced-N 6205 (WiFi network adapter) Microsoft Windows 8 Pro Microsoft Windows [Version 6.2.9200] x64-based PC LENOVO System Model: 3443CTO X1 Carbon Touch I recently noticed this log message When I got disconnected in event viewer: Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x[XXXXXXXXXXXX]. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server. Any idea?

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

< Previous Page | 387 388 389 390 391 392 393 394 395 396 397 398  | Next Page >