Search Results

Search found 14339 results on 574 pages for 'domain rename'.

Page 392/574 | < Previous Page | 388 389 390 391 392 393 394 395 396 397 398 399  | Next Page >

• Installing a DHCP Service On Win2k8 ( Windows Server 2008 )

  - by Akshay Deep Lamba

  Introduction Dynamic Host Configuration Protocol (DHCP) is a core infrastructure service on any network that provides IP addressing and DNS server information to PC clients and any other device. DHCP is used so that you do not have to statically assign IP addresses to every device on your network and manage the issues that static IP addressing can create. More and more, DHCP is being expanded to fit into new network services like the Windows Health Service and Network Access Protection (NAP). However, before you can use it for more advanced services, you need to first install it and configure the basics. Let’s learn how to do that. Installing Windows Server 2008 DHCP Server Installing Windows Server 2008 DCHP Server is easy. DHCP Server is now a “role” of Windows Server 2008 – not a windows component as it was in the past. To do this, you will need a Windows Server 2008 system already installed and configured with a static IP address. You will need to know your network’s IP address range, the range of IP addresses you will want to hand out to your PC clients, your DNS server IP addresses, and your default gateway. Additionally, you will want to have a plan for all subnets involved, what scopes you will want to define, and what exclusions you will want to create. To start the DHCP installation process, you can click Add Roles from the Initial Configuration Tasks window or from Server Manager à Roles à Add Roles. Figure 1: Adding a new Role in Windows Server 2008 When the Add Roles Wizard comes up, you can click Next on that screen. Next, select that you want to add the DHCP Server Role, and click Next. Figure 2: Selecting the DHCP Server Role If you do not have a static IP address assigned on your server, you will get a warning that you should not install DHCP with a dynamic IP address. At this point, you will begin being prompted for IP network information, scope information, and DNS information. If you only want to install DHCP server with no configured scopes or settings, you can just click Next through these questions and proceed with the installation. On the other hand, you can optionally configure your DHCP Server during this part of the installation. In my case, I chose to take this opportunity to configure some basic IP settings and configure my first DHCP Scope. I was shown my network connection binding and asked to verify it, like this: Figure 3: Network connection binding What the wizard is asking is, “what interface do you want to provide DHCP services on?” I took the default and clicked Next. Next, I entered my Parent Domain, Primary DNS Server, and Alternate DNS Server (as you see below) and clicked Next. Figure 4: Entering domain and DNS information I opted NOT to use WINS on my network and I clicked Next. Then, I was promoted to configure a DHCP scope for the new DHCP Server. I have opted to configure an IP address range of 192.168.1.50-100 to cover the 25+ PC Clients on my local network. To do this, I clicked Add to add a new scope. As you see below, I named the Scope WBC-Local, configured the starting and ending IP addresses of 192.168.1.50-192.168.1.100, subnet mask of 255.255.255.0, default gateway of 192.168.1.1, type of subnet (wired), and activated the scope. Figure 5: Adding a new DHCP Scope Back in the Add Scope screen, I clicked Next to add the new scope (once the DHCP Server is installed). I chose to Disable DHCPv6 stateless mode for this server and clicked Next. Then, I confirmed my DHCP Installation Selections (on the screen below) and clicked Install. Figure 6: Confirm Installation Selections After only a few seconds, the DHCP Server was installed and I saw the window, below: Figure 7: Windows Server 2008 DHCP Server Installation succeeded I clicked Close to close the installer window, then moved on to how to manage my new DHCP Server. How to Manage your new Windows Server 2008 DHCP Server Like the installation, managing Windows Server 2008 DHCP Server is also easy. Back in my Windows Server 2008 Server Manager, under Roles, I clicked on the new DHCP Server entry. Figure 8: DHCP Server management in Server Manager While I cannot manage the DHCP Server scopes and clients from here, what I can do is to manage what events, services, and resources are related to the DHCP Server installation. Thus, this is a good place to go to check the status of the DHCP Server and what events have happened around it. However, to really configure the DHCP Server and see what clients have obtained IP addresses, I need to go to the DHCP Server MMC. To do this, I went to Start à Administrative Tools à DHCP Server, like this: Figure 9: Starting the DHCP Server MMC When expanded out, the MMC offers a lot of features. Here is what it looks like: Figure 10: The Windows Server 2008 DHCP Server MMC The DHCP Server MMC offers IPv4 & IPv6 DHCP Server info including all scopes, pools, leases, reservations, scope options, and server options. If I go into the address pool and the scope options, I can see that the configuration we made when we installed the DHCP Server did, indeed, work. The scope IP address range is there, and so are the DNS Server & default gateway. Figure 11: DHCP Server Address Pool Figure 12: DHCP Server Scope Options So how do we know that this really works if we do not test it? The answer is that we do not. Now, let’s test to make sure it works. How do we test our Windows Server 2008 DHCP Server? To test this, I have a Windows Vista PC Client on the same network segment as the Windows Server 2008 DHCP server. To be safe, I have no other devices on this network segment. I did an IPCONFIG /RELEASE then an IPCONFIG /RENEW and verified that I received an IP address from the new DHCP server, as you can see below: Figure 13: Vista client received IP address from new DHCP Server Also, I went to my Windows 2008 Server and verified that the new Vista client was listed as a client on the DHCP server. This did indeed check out, as you can see below: Figure 14: Win 2008 DHCP Server has the Vista client listed under Address Leases With that, I knew that I had a working configuration and we are done!

  Read the article

• Curing the Database-Application mismatch

  - by Phil Factor

  If an application requires access to a database, then you have to be able to deploy it so as to be version-compatible with the database, in phase. If you can deploy both together, then the application and database must normally be deployed at the same version in which they, together, passed integration and functional testing.  When a single database supports more than one application, then the problem gets more interesting. I’ll need to be more precise here. It is actually the application-interface definition of the database that needs to be in a compatible ‘version’.  Most databases that get into production have no separate application-interface; in other words they are ‘close-coupled’.  For this vast majority, the whole database is the application-interface, and applications are free to wander through the bowels of the database scot-free.  If you’ve spurned the perceived wisdom of application architects to have a defined application-interface within the database that is based on views and stored procedures, any version-mismatch will be as sensitive as a kitten.  A team that creates an application that makes direct access to base tables in a database will have to put a lot of energy into keeping Database and Application in sync, to say nothing of having to tackle issues such as security and audit. It is not the obvious route to development nirvana. I’ve been in countless tense meetings with application developers who initially bridle instinctively at the apparent restrictions of being ‘banned’ from the base tables or routines of a database.  There is no good technical reason for needing that sort of access that I’ve ever come across.  Everything that the application wants can be delivered via a set of views and procedures, and with far less pain for all concerned: This is the application-interface.  If more than zero developers are creating a database-driven application, then the project will benefit from the loose-coupling that an application interface brings. What is important here is that the database development role is separated from the application development role, even if it is the same developer performing both roles. The idea of an application-interface with a database is as old as I can remember. The big corporate or government databases generally supported several applications, and there was little option. When a new application wanted access to an existing corporate database, the developers, and myself as technical architect, would have to meet with hatchet-faced DBAs and production staff to work out an interface. Sure, they would talk up the effort involved for budgetary reasons, but it was routine work, because it decoupled the database from its supporting applications. We’d be given our own stored procedures. One of them, I still remember, had ninety-two parameters. All database access was encapsulated in one application-module. If you have a stable defined application-interface with the database (Yes, one for each application usually) you need to keep the external definitions of the components of this interface in version control, linked with the application source,  and carefully track and negotiate any changes between database developers and application developers.  Essentially, the application development team owns the interface definition, and the onus is on the Database developers to implement it and maintain it, in conformance.  Internally, the database can then make all sorts of changes and refactoring, as long as source control is maintained.  If the application interface passes all the comprehensive integration and functional tests for the particular version they were designed for, nothing is broken. Your performance-testing can ‘hang’ on the same interface, since databases are judged on the performance of the application, not an ‘internal’ database process. The database developers have responsibility for maintaining the application-interface, but not its definition,  as they refactor the database. This is easily tested on a daily basis since the tests are normally automated. In this setting, the deployment can proceed if the more stable application-interface, rather than the continuously-changing database, passes all tests for the version of the application. Normally, if all goes well, a database with a well-designed application interface can evolve gracefully without changing the external appearance of the interface, and this is confirmed by integration tests that check the interface, and which hopefully don’t need to be altered at all often.  If the application is rapidly changing its ‘domain model’  in the light of an increased understanding of the application domain, then it can change the interface definitions and the database developers need only implement the interface rather than refactor the underlying database.  The test team will also have to redo the functional and integration tests which are, of course ‘written to’ the definition.  The Database developers will find it easier if these tests are done before their re-wiring  job to implement the new interface. If, at the other extreme, an application receives no further development work but survives unchanged, the database can continue to change and develop to keep pace with the requirements of the other applications it supports, and needs only to take care that the application interface is never broken. Testing is easy since your automated scripts to test the interface do not need to change. The database developers will, of course, maintain their own source control for the database, and will be likely to maintain versions for all major releases. However, this will not need to be shared with the applications that the database servers. On the other hand, the definition of the application interfaces should be within the application source. Changes in it have to be subject to change-control procedures, as they will require a chain of tests. Once you allow, instead of an application-interface, an intimate relationship between application and database, we are in the realms of impedance mismatch, over and above the obvious security problems.  Part of this impedance problem is a difference in development practices. Whereas the application has to be regularly built and integrated, this isn’t necessarily the case with the database.  An RDBMS is inherently multi-user and self-integrating. If the developers work together on the database, then a subsequent integration of the database on a staging server doesn’t often bring nasty surprises. A separate database-integration process is only needed if the database is deliberately built in a way that mimics the application development process, but which hampers the normal database-development techniques.  This process is like demanding a official walking with a red flag in front of a motor car.  In order to closely coordinate databases with applications, entire databases have to be ‘versioned’, so that an application version can be matched with a database version to produce a working build without errors.  There is no natural process to ‘version’ databases.  Each development project will have to define a system for maintaining the version level. A curious paradox occurs in development when there is no formal application-interface. When the strains and cracks happen, the extra meetings, bureaucracy, and activity required to maintain accurate deployments looks to IT management like work. They see activity, and it looks good. Work means progress.  Management then smile on the design choices made. In IT, good design work doesn’t necessarily look good, and vice versa.

  Read the article

• SQL SERVER – Weekly Series – Memory Lane – #034

  - by Pinal Dave

  Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2007 UDF – User Defined Function to Strip HTML – Parse HTML – No Regular Expression The UDF used in the blog does fantastic task – it scans entire HTML text and removes all the HTML tags. It keeps only valid text data without HTML task. This is one of the quite commonly requested tasks many developers have to face everyday. De-fragmentation of Database at Operating System to Improve Performance Operating system skips MDF file while defragging the entire filesystem of the operating system. It is absolutely fine and there is no impact of the same on performance. Read the entire blog post for my conversation with our network engineers. Delay Function – WAITFOR clause – Delay Execution of Commands How do you delay execution of the commands in SQL Server – ofcourse by using WAITFOR keyword. In this blog post, I explain the same with the help of T-SQL script. Find Length of Text Field To measure the length of TEXT fields the function is DATALENGTH(textfield). Len will not work for text field. As of SQL Server 2005, developers should migrate all the text fields to VARCHAR(MAX) as that is the way forward. Retrieve Current Date Time in SQL Server CURRENT_TIMESTAMP, GETDATE(), {fn NOW()} There are three ways to retrieve the current datetime in SQL SERVER. CURRENT_TIMESTAMP, GETDATE(), {fn NOW()} Explanation and Comparison of NULLIF and ISNULL An interesting observation is NULLIF returns null if it comparison is successful, whereas ISNULL returns not null if its comparison is successful. In one way they are opposite to each other. Here is my question to you - How to create infinite loop using NULLIF and ISNULL? If this is even possible? 2008 Introduction to SERVERPROPERTY and example SERVERPROPERTY is a very interesting system function. It returns many of the system values. I use it very frequently to get different server values like Server Collation, Server Name etc. SQL Server Start Time We can use DMV to find out what is the start time of SQL Server in 2008 and later version. In this blog you can see how you can do the same. Find Current Identity of Table Many times we need to know what is the current identity of the column. I have found one of my developers using aggregated function MAX () to find the current identity. However, I prefer following DBCC command to figure out current identity. Create Check Constraint on Column Some time we just need to create a simple constraint over the table but I have noticed that developers do many different things to make table column follow rules than just creating constraint. I suggest constraint is a very useful concept and every SQL Developer should pay good attention to this subject. 2009 List Schema Name and Table Name for Database This is one of the blog post where I straight forward display script. One of the kind of blog posts, which I still love to read and write. Clustered Index on Separate Drive From Table Location A table devoid of primary key index is called heap, and here data is not arranged in a particular order, which gives rise to issues that adversely affect performance. Data must be stored in some kind of order. If we put clustered index on it then the order will be forced by that index and the data will be stored in that particular order. Understanding Table Hints with Examples Hints are options and strong suggestions specified for enforcement by the SQL Server query processor on DML statements. The hints override any execution plan the query optimizer might select for a query. 2010 Data Pages in Buffer Pool – Data Stored in Memory Cache One of my earlier year article, which I still read it many times and point developers to read it again. It is clear from the Resultset that when more than one index is used, datapages related to both or all of the indexes are stored in Memory Cache separately. TRANSACTION, DML and Schema Locks Can you create a situation where you can see Schema Lock? Well, this is a very simple question, however during the interview I notice over 50 candidates failed to come up with the scenario. In this blog post, I have demonstrated the situation where we can see the schema lock in database. 2011 Solution – Puzzle – Statistics are not updated but are Created Once In this example I have created following situation: Create Table Insert 1000 Records Check the Statistics Now insert 10 times more 10,000 indexes Check the Statistics – it will be NOT updated Auto Update Statistics and Auto Create Statistics for database is TRUE Now I have requested two things in the example 1) Why this is happening? 2) How to fix this issue? Selecting Domain from Email Address This is a straight to script blog post where I explain how to select only domain name from entire email address. Solution – Generating Zero Without using Any Numbers in T-SQL How to get zero digit without using any digit? This is indeed a very interesting question and the answer is even interesting. Try to come up with answer in next 10 minutes and if you can’t come up with the answer the blog post read this post for solution. 2012 Simple Explanation and Puzzle with SOUNDEX Function and DIFFERENCE Function In simple words - SOUNDEX converts an alphanumeric string to a four-character code to find similar-sounding words or names. DIFFERENCE function returns an integer value. The  integer returned is the number of characters in the SOUNDEX values that are the same. Read Only Files and SQL Server Management Studio (SSMS) I have come across a very interesting feature in SSMS related to “Read Only” files. I believe it is a little unknown feature as well so decided to write a blog about the same. Identifying Column Data Type of uniqueidentifier without Querying System Tables How do I know if any table has a uniqueidentifier column and what is its value without using any DMV or System Catalogues? Only information you know is the table name and you are allowed to return any kind of error if the table does not have uniqueidentifier column. Read the blog post to find the answer. Solution – User Not Able to See Any User Created Object in Tables – Security and Permissions Issue Interesting question – “When I try to connect to SQL Server, it lets me connect just fine as well let me open and explore the database. I noticed that I do not see any user created instances but when my colleague attempts to connect to the server, he is able to explore the database as well see all the user created tables and other objects. Can you help me fix it?” Importing CSV File Into Database – SQL in Sixty Seconds #018 – Video Here is interesting small 60 second video on how to import CSV file into Database. ColumnStore Index – Batch Mode vs Row Mode Here is the logic behind when Columnstore Index uses Batch Mode and when it uses Row Mode. A batch typically represents about 1000 rows of data. Batch mode processing also uses algorithms that are optimized for the multicore CPUs and increased memory throughput. Follow up – Usage of $rowguid and $IDENTITY This is an excellent follow up blog post of my earlier blog post where I explain where to use $rowguid and $identity.  If you do not know the difference between them, this is a blog with a script example. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• PowerShell Script to Enumerate SharePoint 2010 or 2013 Permissions and Active Directory Group Membership

  - by Brian T. Jackett

  Originally posted on: http://geekswithblogs.net/bjackett/archive/2013/07/01/powershell-script-to-enumerate-sharepoint-2010-or-2013-permissions-and.aspx   In this post I will present a script to enumerate SharePoint 2010 or 2013 permissions across the entire farm down to the site (SPWeb) level.  As a bonus this script also recursively expands the membership of any Active Directory (AD) group including nested groups which you wouldn’t be able to find through the SharePoint UI.   History     Back in 2009 (over 4 years ago now) I published one my most read blog posts about enumerating SharePoint 2007 permissions.  I finally got around to updating that script to remove deprecated APIs, supporting the SharePoint 2010 commandlets, and fixing a few bugs.  There are 2 things that script did that I had to remove due to major architectural or procedural changes in the script. Indenting the XML output Ability to search for a specific user    I plan to add back the ability to search for a specific user but wanted to get this version published first.  As for indenting the XML that could be added but would take some effort.  If there is user demand for it (let me know in the comments or email me using the contact button at top of blog) I’ll move it up in priorities.    As a side note you may also notice that I’m not using the Active Directory commandlets.  This was a conscious decision since not all environments have them available.  Instead I’m relying on the older [ADSI] type accelerator and APIs.  It does add a significant amount of code to the script but it is necessary for compatibility.  Hopefully in a few years if I need to update again I can remove that legacy code.   Solution    Below is the script to enumerate SharePoint 2010 and 2013 permissions down to site level.  You can also download it from my SkyDrive account or my posting on the TechNet Script Center Repository. SkyDrive TechNet Script Center Repository http://gallery.technet.microsoft.com/scriptcenter/Enumerate-SharePoint-2010-35976bdb   001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 ########################################################### #DisplaySPWebApp8.ps1 # #Author: Brian T. Jackett #Last Modified Date: 2013-07-01 # #Traverse the entire web app site by site to display # hierarchy and users with permissions to site. ########################################################### function Expand-ADGroupMembership {     Param     (         [Parameter(Mandatory=$true,                    Position=0)]         [string]         $ADGroupName,         [Parameter(Position=1)]         [string]         $RoleBinding     )     Process     {         $roleBindingText = ""         if(-not [string]::IsNullOrEmpty($RoleBinding))         {             $roleBindingText = " RoleBindings=`"$roleBindings`""         }         Write-Output "<ADGroup Name=`"$($ADGroupName)`"$roleBindingText>"         $domain = $ADGroupName.substring(0, $ADGroupName.IndexOf("\") + 1)         $groupName = $ADGroupName.Remove(0, $ADGroupName.IndexOf("\") + 1)                                     #BEGIN - CODE ADAPTED FROM SCRIPT CENTER SAMPLE CODE REPOSITORY         #http://www.microsoft.com/technet/scriptcenter/scripts/powershell/search/users/srch106.mspx         #GET AD GROUP FROM DIRECTORY SERVICES SEARCH         $strFilter = "(&(objectCategory=Group)(name="+($groupName)+"))"         $objDomain = New-Object System.DirectoryServices.DirectoryEntry         $objSearcher = New-Object System.DirectoryServices.DirectorySearcher         $objSearcher.SearchRoot = $objDomain         $objSearcher.Filter = $strFilter         # specify properties to be returned         $colProplist = ("name","member","objectclass")         foreach ($i in $colPropList)         {             $catcher = $objSearcher.PropertiesToLoad.Add($i)         }         $colResults = $objSearcher.FindAll()         #END - CODE ADAPTED FROM SCRIPT CENTER SAMPLE CODE REPOSITORY         foreach ($objResult in $colResults)         {             if($objResult.Properties["Member"] -ne $null)             {                 foreach ($member in $objResult.Properties["Member"])                 {                     $indMember = [adsi] "LDAP://$member"                     $fullMemberName = $domain + ($indMember.Name)                                         #if($indMember["objectclass"]                         # if child AD group continue down chain                         if(($indMember | Select-Object -ExpandProperty objectclass) -contains "group")                         {                             Expand-ADGroupMembership -ADGroupName $fullMemberName                         }                         elseif(($indMember | Select-Object -ExpandProperty objectclass) -contains "user")                         {                             Write-Output "<ADUser>$fullMemberName</ADUser>"                         }                 }             }         }                 Write-Output "</ADGroup>"     } } #end Expand-ADGroupMembership # main portion of script if((Get-PSSnapin -Name microsoft.sharepoint.powershell) -eq $null) {     Add-PSSnapin Microsoft.SharePoint.PowerShell } $farm = Get-SPFarm Write-Output "<Farm Guid=`"$($farm.Id)`">" $webApps = Get-SPWebApplication foreach($webApp in $webApps) {     Write-Output "<WebApplication URL=`"$($webApp.URL)`" Name=`"$($webApp.Name)`">"     foreach($site in $webApp.Sites)     {         Write-Output "<SiteCollection URL=`"$($site.URL)`">"                 foreach($web in $site.AllWebs)         {             Write-Output "<Site URL=`"$($web.URL)`">"             # if site inherits permissions from parent then stop processing             if($web.HasUniqueRoleAssignments -eq $false)             {                 Write-Output "<!-- Inherits role assignments from parent -->"             }             # else site has unique permissions             else             {                 foreach($assignment in $web.RoleAssignments)                 {                     if(-not [string]::IsNullOrEmpty($assignment.Member.Xml))                     {                         $roleBindings = ($assignment.RoleDefinitionBindings | Select-Object -ExpandProperty name) -join ","                         # check if assignment is SharePoint Group                         if($assignment.Member.XML.StartsWith('<Group') -eq "True")                         {                             Write-Output "<SPGroup Name=`"$($assignment.Member.Name)`" RoleBindings=`"$roleBindings`">"                             foreach($SPGroupMember in $assignment.Member.Users)                             {                                 # if SharePoint group member is an AD Group                                 if($SPGroupMember.IsDomainGroup)                                 {                                     Expand-ADGroupMembership -ADGroupName $SPGroupMember.Name                                 }                                 # else SharePoint group member is an AD User                                 else                                 {                                     # remove claim portion of user login                                     #Write-Output "<ADUser>$($SPGroupMember.UserLogin.Remove(0,$SPGroupMember.UserLogin.IndexOf("|") + 1))</ADUser>"                                     Write-Output "<ADUser>$($SPGroupMember.UserLogin)</ADUser>"                                 }                             }                             Write-Output "</SPGroup>"                         }                         # else an indivdually listed AD group or user                         else                         {                             if($assignment.Member.IsDomainGroup)                             {                                 Expand-ADGroupMembership -ADGroupName $assignment.Member.Name -RoleBinding $roleBindings                             }                             else                             {                                 # remove claim portion of user login                                 #Write-Output "<ADUser>$($assignment.Member.UserLogin.Remove(0,$assignment.Member.UserLogin.IndexOf("|") + 1))</ADUser>"                                                                 Write-Output "<ADUser RoleBindings=`"$roleBindings`">$($assignment.Member.UserLogin)</ADUser>"                             }                         }                     }                 }             }             Write-Output "</Site>"             $web.Dispose()         }         Write-Output "</SiteCollection>"         $site.Dispose()     }     Write-Output "</WebApplication>" } Write-Output "</Farm>"      The output from the script can be sent to an XML which you can then explore using the [XML] type accelerator.  This lets you explore the XML structure however you see fit.  See the screenshot below for an example.      If you do view the XML output through a text editor (Notepad++ for me) notice the format.  Below we see a SharePoint site that has a SharePoint group Demo Members with Edit permissions assigned.  Demo Members has an AD group corp\developers as a member.  corp\developers has a child AD group called corp\DevelopersSub with 1 AD user in that sub group.  As you can see the script recursively expands the AD hierarchy.   Conclusion    It took me 4 years to finally update this script but I‘m happy to get this published.  I was able to fix a number of errors and smooth out some rough edges.  I plan to develop this into a more full fledged tool over the next year with more features and flexibility (copy permissions, search for individual user or group, optional enumerate lists / items, etc.).  If you have any feedback, feature requests, or issues running it please let me know.  Enjoy the script!         -Frog Out

  Read the article

• Instructions on how to configure a WebLogic Cluster and use it with Oracle Http Server

  - by Laurent Goldsztejn

  On October 17th I delivered a webcast on WebLogic Clustering that included a demo with Apache as the proxy server.  I realized that many steps are needed to set up the configuration I used during the demo.  The purpose of this article is to go through these steps to show how quickly and easily one can define a new cluster and then proxy requests via an Oracle Http Server (OHS). The domain configuration wizard offers the option to create a cluster.  The administration console or WLST, the Weblogic scripting tool can also be used to define a new cluster.  It can be created at any time but the servers that will participate in it cannot be in a running state. Cluster Creation using the configuration wizard Network and architecture requirements need to be considered while choosing between unicast and multicast. Multicast Vs. Unicast with WebLogic Clustering is of great help to make the best decision between the two messaging modes.  In addition, Configure Cluster offers details on each single field displayed above. After this initial configuration page, individual servers could be assigned to this newly created cluster although servers can be added later to the cluster.  What is not recommended is for the Admin server to participate in a cluster as the main purpose of the Admin server is to perform the bulk of the processing for the domain.  Servers need to stop before being assigned to a cluster.  There is also no minimum number of servers that have to participate in the cluster. At this point the configuration should be done and the cluster created successfully.  This can easily be verified from the console. Each clustered managed server can be launched to join the cluster.   At startup the following messages should be logged for each clustered managed server: <Notice> <WeblogicServer> <BEA-000365> <Server state changed to STARTING> <Notice> <Cluster> <BEA-000197> <Listening for announcements from cluster using messaging_mode cluster messaging> <Notice> <Cluster> <BEA-000133> <Waiting to synchronize with other running members of cluster_name>  It's time to try sending requests to the cluster and we will do this with the help of Oracle Http Server to play the role of a proxy server to demonstrate load balancing.  Proxy Server configuration  The first step is to download Weblogic Server Web Server Plugin that will enhance the web server by handling requests aimed at being sent to the Weblogic cluster.  For our test Oracle Http Server (OHS) will be used.  However plug-ins are also available for Apache Http server, Microsoft Internet Information Server (IIS), Oracle iPlanet Webserver or even WebLogic Server with the HttpClusterServlet. Once OHS is installed on the system, the configuration file, mod_wl_ohs.conf, will need to be altered to include Weblogic proxy specifics. First of all, add the following directive to instruct Apache to load the Weblogic shared object module extracted from the plugins file just downloaded. LoadModule weblogic_module modules/mod_wl_ohs.so and then create an IfModule directive to encapsulate the following location block so that proxy will be enabled by path (each request including /wls will be directed directly to the WebLogic Cluster).  You could also proxy requests by MIME type using MatchExpression in the Location block. <IfModule weblogic_module> <Location /wls>    SetHandler weblogic-handler    PathTrim /wls    WebLogicCluster MS1_URL:port,MS2_URL:port    Debug ON    WLLogFile        c:/tmp/global_proxy.log     WLTempDir        "c:/myTemp"    DebugConfigInfo  On </Location> </IfModule> SetHandler specifies the handler for the plug-in module  PathTrim will instruct the plug-in to trim /w ls from the URL before forwarding the request to the cluster. The list of WebLogic Servers defined in WeblogicCluster could contain a mixed set of clustered and single servers.  However, the dynamic list returned for this parameter will only contain valid clustered servers and may contain more servers if not all clustered servers are listed in WeblogicCluster. Testing proxy and load balancing It's time to start OHS web server which should at this point be configured correctly to proxy requests to the clustered servers.  By default round-robin is the load balancing strategy set by WebLogic. Testing the load balancing can be easily done by disabling cookies on your browser given that a request containing a cookie attempts to connect to the primary server. If that attempt fails, the plug-in attempts to make a connection to the next available server in the list in a round-robin fashion.  With cookies enabled, you could use two different browsers to test the load balancing with a JSP page that contains the following: <%@ page contentType="text/html; charset=iso-8859-1" language="java"  %>  <%  String path = request.getContextPath();   String getProtocol=request.getScheme();   String getDomain=request.getServerName();   String getPort=Integer.toString(request.getLocalPort());   String getPath = getProtocol+"://"+getDomain+":"+getPort+path+"/"; %> <html> <body> Receiving Server <%=getPath%> </body> </html>  Assuming that you name the JSP page Test.jsp and the webapp that contains it TestApp, your browsers should open the following URL: http://localhost/wls/TestApp/Test.jsp  Each browser should connect to a different clustered server and this simple JSP should confirm that.  The webapp that contains the JSP needs to be deployed to the cluster. You can also verify that the load is correctly balanced by looking at the proxy log file.  Each request generates a set of log entries that starts with : timestamp ================New Request: Each request is associated with a primary server and a secondary server if one is available.  For our test request, the following entries should appear in the log as well:Using Uri /wls/TestApp/Test.jsp After trimming path: '/TestApp/Test.jsp' The final request string is '/TestApp/Test.jsp' If an exception occurs, it should also be logged in the proxy log file with the prefix:timestamp *******Exception type   WeblogicBridgeConfig DebugConfigInfo enables runtime statistics and the production of configuration information.  For security purposes, this parameter should be turned off in production. http://webserver_host:port/path/xyz.jsp?__WebLogicBridgeConfig will display a proxy bridge page detailing the plugin configuration followed by runtime statistics which could help in diagnosing issues along with the analyzing of the proxy log file.  In our example the url would be: http://localhost/wls/TestApp/Test.jsp?__WebLogicBridgeConfig  Here is how the top section of the screen can look like: The bottom part of the page contains runtime statistics, here is a snippet of it (unrelated with the previous JSP example).   This entire plugin configuration should be very similar with other web servers, what varies is the name of the proxy server configuration file. So, as you can see, it only takes a few minutes to configure a Weblogic cluster and get servers to join it. 

  Read the article

• Refactoring Part 1 : Intuitive Investments

  - by Wes McClure

  Fear, it’s what turns maintaining applications into a nightmare.  Technology moves on, teams move on, someone is left to operate the application, what was green is now perceived brown.  Eventually the business will evolve and changes will need to be made.  The approach to those changes often dictates the long term viability of the application.  Fear of change, lack of passion and a lack of interest in understanding the domain often leads to a paranoia to do anything that doesn’t involve duct tape and bailing twine.  Don’t get me wrong, those have a place in the short term viability of a project but they don’t have a place in the long term.  Add to it “us versus them” in regards to the original team and those that maintain it, internal politics and other factors and you have a recipe for disaster.  This results in code that quickly becomes unmanageable.  Even the most clever of designs will eventually become sub optimal and debt will amount that exponentially makes changes difficult.  This is where refactoring comes in, and it’s something I’m very passionate about.  Refactoring is about improving the process whereby we make change, it’s an exponential investment in the process of change. Without it we will incur exponential complexity that halts productivity. Investments, especially in the long term, require intuition and reflection.  How can we tackle new development effectively via evolving the original design and paying off debt that has been incurred? The longer we wait to ask and answer this question, the more it will cost us.  Small requests don’t warrant big changes, but realizing when changes now will pay off in the long term, and especially in the short term, is valuable. I have done my fair share of maintaining applications and continuously refactoring as needed, but recently I’ve begun work on a project that hasn’t had much debt, if any, paid down in years.  This is the first in a series of blog posts to try to capture the process which is largely driven by intuition of smaller refactorings from other projects. Signs that refactoring could help: Testability How can decreasing test time not pay dividends? One of the first things I found was that a very important piece often takes 30+ minutes to test.  I can only imagine how much time this has cost historically, but more importantly the time it might cost in the coming weeks: I estimate at least 10-20 hours per person!  This is simply unacceptable for almost any situation.  As it turns out, about 6 hours of working with this part of the application and I was able to cut the time down to under 30 seconds!  In less than the lost time of one week, I was able to fix the problem for all future weeks! If we can’t test fast then we can’t change fast, nor with confidence. Code is used by end users and it’s also used by developers, consider your own needs in terms of the code base.  Adding logic to enable/disable features during testing can help decouple parts of an application and lead to massive improvements.  What exactly is so wrong about test code in real code?  Often, these become features for operators and sometimes end users.  If you cannot run an integration test within a test runner in your IDE, it’s time to refactor. Readability Are variables named meaningfully via a ubiquitous language? Is the code segmented functionally or behaviorally so as to minimize the complexity of any one area? Are aspects properly segmented to avoid confusion (security, logging, transactions, translations, dependency management etc) Is the code declarative (what) or imperative (how)?  What matters, not how.  LINQ is a great abstraction of the what, not how, of collection manipulation.  The Reactive framework is a great example of the what, not how, of managing streams of data. Are constants abstracted and named, or are they just inline? Do people constantly bitch about the code/design? If the code is hard to understand, it will be hard to change with confidence.  It’s a large undertaking if the original designers didn’t pay much attention to readability and as such will never be done to “completion.”  Make sure not to go over board, instead use this as you change an application, not in lieu of changes (like with testability). Complexity Simplicity will never be achieved, it’s highly subjective.  That said, a lot of code can be significantly simplified, tidy it up as you go.  Refactoring will often converge upon a simplification step after enough time, keep an eye out for this. Understandability In the process of changing code, one often gains a better understanding of it.  Refactoring code is a good way to learn how it works.  However, it’s usually best in combination with other reasons, in effect killing two birds with one stone.  Often this is done when readability is poor, in which case understandability is usually poor as well.  In the large undertaking we are making with this legacy application, we will be replacing it.  Therefore, understanding all of its features is important and this refactoring technique will come in very handy. Unused code How can deleting things not help? This is a freebie in refactoring, it’s very easy to detect with modern tools, especially in statically typed languages.  We have VCS for a reason, if in doubt, delete it out (ok that was cheesy)! If you don’t know where to start when refactoring, this is an excellent starting point! Duplication Do not pray and sacrifice to the anti-duplication gods, there are excellent examples where consolidated code is a horrible idea, usually with divergent domains.  That said, mediocre developers live by copy/paste.  Other times features converge and aren’t combined.  Tools for finding similar code are great in the example of copy/paste problems.  Knowledge of the domain helps identify convergent concepts that often lead to convergent solutions and will give intuition for where to look for conceptual repetition. 80/20 and the Boy Scouts It’s often said that 80% of the time 20% of the application is used most.  These tend to be the parts that are changed.  There are also parts of the code where 80% of the time is spent changing 20% (probably for all the refactoring smells above).  I focus on these areas any time I make a change and follow the philosophy of the Boy Scout in cleaning up more than I messed up.  If I spend 2 hours changing an application, in the 20%, I’ll always spend at least 15 minutes cleaning it or nearby areas. This gives a huge productivity edge on developers that don’t. Ironically after a short period of time the 20% shrinks enough that we don’t have to spend 80% of our time there and can move on to other areas.   Refactoring is highly subjective, never attempt to refactor to completion!  Learn to be comfortable with leaving one part of the application in a better state than others.  It’s an evolution, not a revolution.  These are some simple areas to look into when making changes and can help get one started in the process.  I’ve often found that refactoring is a convergent process towards simplicity that sometimes spans a few hours but often can lead to massive simplifications over the timespan of weeks and months of regular development.

  Read the article

• Protecting Cookies: Once and For All

  - by Your DisplayName here!

  Every once in a while you run into a situation where you need to temporarily store data for a user in a web app. You typically have two options here – either store server-side or put the data into a cookie (if size permits). When you need web farm compatibility in addition – things become a little bit more complicated because the data needs to be available on all nodes. In my case I went for a cookie – but I had some requirements Cookie must be protected from eavesdropping (sent only over SSL) and client script Cookie must be encrypted and signed to be protected from tampering with Cookie might become bigger than 4KB – some sort of overflow mechanism would be nice I really didn’t want to implement another cookie protection mechanism – this feels wrong and btw can go wrong as well. WIF to the rescue. The session management feature already implements the above requirements but is built around de/serializing IClaimsPrincipals into cookies and back. But if you go one level deeper you will find the CookieHandler and CookieTransform classes which contain all the needed functionality. public class ProtectedCookie {     private List<CookieTransform> _transforms;     private ChunkedCookieHandler _handler = new ChunkedCookieHandler();     // DPAPI protection (single server)     public ProtectedCookie()     {         _transforms = new List<CookieTransform>             {                 new DeflateCookieTransform(),                 new ProtectedDataCookieTransform()             };     }     // RSA protection (load balanced)     public ProtectedCookie(X509Certificate2 protectionCertificate)     {         _transforms = new List<CookieTransform>             {                 new DeflateCookieTransform(),                 new RsaSignatureCookieTransform(protectionCertificate),                 new RsaEncryptionCookieTransform(protectionCertificate)             };     }     // custom transform pipeline     public ProtectedCookie(List<CookieTransform> transforms)     {         _transforms = transforms;     }     public void Write(string name, string value, DateTime expirationTime)     {         byte[] encodedBytes = EncodeCookieValue(value);         _handler.Write(encodedBytes, name, expirationTime);     }     public void Write(string name, string value, DateTime expirationTime, string domain, string path)     {         byte[] encodedBytes = EncodeCookieValue(value);         _handler.Write(encodedBytes, name, path, domain, expirationTime, true, true, HttpContext.Current);     }     public string Read(string name)     {         var bytes = _handler.Read(name);         if (bytes == null || bytes.Length == 0)         {             return null;         }         return DecodeCookieValue(bytes);     }     public void Delete(string name)     {         _handler.Delete(name);     }     protected virtual byte[] EncodeCookieValue(string value)     {         var bytes = Encoding.UTF8.GetBytes(value);         byte[] buffer = bytes;         foreach (var transform in _transforms)         {             buffer = transform.Encode(buffer);         }         return buffer;     }     protected virtual string DecodeCookieValue(byte[] bytes)     {         var buffer = bytes;         for (int i = _transforms.Count; i > 0; i—)         {             buffer = _transforms[i - 1].Decode(buffer);         }         return Encoding.UTF8.GetString(buffer);     } } HTH

  Read the article

• Feedback on meeting of the Linux User Group of Mauritius

  Once upon a time in a country far far away... Okay, actually it's not that bad but it has been a while since the last meeting of the Linux User Group of Mauritius (LUGM). There have been plans in the past but it never really happened. Finally, Selven took the opportunity and organised a new meetup with low administrative overhead, proper scheduling on alternative dates and a small attendee's survey on the preferred option. All the pre-work was nicely executed. First, I wasn't sure whether it would be possible to attend. Luckily I got some additional information, like children should come, too, and I was sold to this community gathering. According to other long-term members of the LUGM it was the first time 'ever' that a gathering was organised outside of Quatre Bornes, and I have to admit it was great! LUGM - user group meeting on the 15.06.2013 in L'Escalier Quick overview of Linux & the LUGM With a little bit of delay the LUGM meeting officially started with a quick overview and introduction to Linux presented by Avinash. During the session he told the audience that there had been quite some activity over the island some years ago but unfortunately it had been quiet during recent times. Of course, we also spoke about the acknowledged world dominance of Linux - thanks to Android - and the interesting possibilities for countries like Mauritius. It is known that a couple of public institutions have there back-end infrastructure running on Red Hat Linux systems but the presence on the desktop is still very low. Users are simply hanging on to Windows XP and older versions of Microsoft Office. Following the introduction of the LUGM Ajay joined into the session and it quickly changed into a panel discussion with lots of interesting questions and answers, sharing of first-hand experience either on the job or in private use of Linux, and a couple of ideas about how the LUGM could promote Linux a bit more in Mauritius. It was great to get an insight into other attendee's opinion and activities. Especially taking into consideration that I'm already using Linux since around 1996/97. Frankly speaking, I bought a SuSE 4.x distribution back in those days because I couldn't achieve certain tasks on Windows NT 4.0 without spending a fortune. OpenELEC Mediacenter Next, Selven gave us decent introduction on OpenELEC: Open Embedded Linux Entertainment Center (OpenELEC) is a small Linux distribution built from scratch as a platform to turn your computer into an XBMC media center. OpenELEC is designed to make your system boot fast, and the install is so easy that anyone can turn a blank PC into a media machine in less than 15 minutes. I didn't know about it until this presentation. In the past, I was mainly attached to Video Disk Recorder (VDR) as it allows the use of satellite receiver cards very easily. Hm, somehow I'm still missing my precious HTPC that I had to leave back in Germany years ago. It was great piece of hardware and software; self-built PC in a standard HiFi-sized (43cm) black desktop casing with 2 full-featured Hauppauge DVB-s cards, an old-fashioned Voodoo graphics card, WiFi card, Pioneer slot-in DVD drive, and fully remote controlled via infra-red thanks to Debian, VDR and LIRC. With EP Guide, scheduled recordings and general multimedia centre it offered all the necessary comfort in the living room, besides a Nintendo game console; actually a GameCube at that time... But I have to admit that putting OpenELEC on a Raspberry Pi would be a cool DIY project in the near future. LUGM - our next generation of linux users (15.06.2013) Project Evil Genius (PEG) Don't be scared of the paragraph header. Ish gave us a cool explanation why he named it PEG - Project Evil Genius; it's because of the time of the day when he was scripting down his ideas to be able to build, package and provide software applications to various Linux distributions. The main influence came from openSuSE but the platform didn't cater for his needs and ideas, so he started to work out something on his own. During his passionate session he also talked about the amazing experience he had due to other Linux users from all over the world. During the next couple of days Ish promised to put his script to GitHub... Looking forward to that. Check out Ish's personal blog over at hacklog.in. Highly recommended to read. Why India? Simply because the registration fees per year for an Indian domain are approximately 20 times less than for a Mauritian domain (.mu). Exploring the beach of L'Escalier af the meeting 'After-party' at the beach of L'Escalier Puh, after such interesting sessions, ideas around Linux and good conversation during the breaks and over lunch it was time for a little break-out. Selven suggested that we all should head down to the beach of L'Escalier and get some impressions of nature down here in the south of the island. Talking about 'beach' ;-) - absolutely not comparable to the white-sanded ones here in Flic en Flac... There are no lagoons down at the south coast of Mauriitus, and watching the breaking waves is a different experience and joy after all. Unfortunately, I was a little bit worried about the thoughtless littering at such a remote location. You have to drive on natural paths through the sugar cane fields and I was really shocked by the amount of rubbish lying around almost everywhere. Sad, really sad and it concurs with Yasir's recent article on the same topic. Resumé & outlook It was a great event. I met with new people, had some good conversations, and even my children enjoyed themselves the whole day. The location was well-chosen, enough space for each and everyone, parking spaces and even a playground for the children. Also, a big "Thank You" to Selven and his helpers for the organisation and preparation of lunch. I'm kind of sure that this was an exceptional meeting of LUGM and I'm really looking forward to the next gathering of Linux geeks. Hopefully, soon. All images are courtesy of Avinash Meetoo. More pictures are available on Flickr.

  Read the article

• Error while installation of CHMSee

  - by Anshuman Chakraborty

  I have recently migrated from Windows to Ubuntu. My current locale shows below output :- cha@COMPUTER:~$ locale LANG=en_IN LANGUAGE=en_IN:en LC_CTYPE="en_IN" LC_NUMERIC="en_IN" LC_TIME="en_IN" LC_COLLATE="en_IN" LC_MONETARY="en_IN" LC_MESSAGES="en_IN" LC_PAPER="en_IN" LC_NAME="en_IN" LC_ADDRESS="en_IN" LC_TELEPHONE="en_IN" LC_MEASUREMENT="en_IN" LC_IDENTIFICATION="en_IN" LC_ALL= When I am trying to install CHMSee (or any other Application) using UBUNTU Software Center. I am getting below error. installArchives() failed: perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "en_IN.ISO8859-1" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Selecting previously unselected package libchm1. (Reading database ... (Reading database ... 5% (Reading database ... 10% (Reading database ... 15% (Reading database ... 20% (Reading database ... 25% (Reading database ... 30% (Reading database ... 35% (Reading database ... 40% (Reading database ... 45% (Reading database ... 50% (Reading database ... 55% (Reading database ... 60% (Reading database ... 65% (Reading database ... 70% (Reading database ... 75% (Reading database ... 80% (Reading database ... 85% (Reading database ... 90% (Reading database ... 95% (Reading database ... 100% (Reading database ... 207053 files and directories currently installed.) Unpacking libchm1 (from .../libchm1_2%3a0.40a-1_i386.deb) ... Selecting previously unselected package libjavascriptcoregtk-1.0-0. Unpacking libjavascriptcoregtk-1.0-0 (from .../libjavascriptcoregtk-1.0-0_1.8.0-0ubuntu2_i386.deb) ... Selecting previously unselected package libwebkitgtk-1.0-common. Unpacking libwebkitgtk-1.0-common (from .../libwebkitgtk-1.0-common_1.8.0-0ubuntu2_all.deb) ... Selecting previously unselected package libwebkitgtk-1.0-0. Unpacking libwebkitgtk-1.0-0 (from .../libwebkitgtk-1.0-0_1.8.0-0ubuntu2_i386.deb) ... Selecting previously unselected package chmsee. Unpacking chmsee (from .../chmsee_1.3.0-2ubuntu2_i386.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for man-db ... locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Setting up qmail (1.06-4) ... The hostname -f command returned: $1 Your system needs to have a fully qualified domain name (fqdn) in order to install the var-qmail packages. Installation aborted. dpkg: error processing qmail (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of qmail-run: qmail-run depends on qmail (>= 1.06-2.1); however: Package qmail is not configured yet. dpkg: error processing qmail-run (--configure): dependency problems - leaving unconfigured Setting up libchm1 (2:0.40a-1) ... No apport report written because the error message indicates its a followup error from a previous failure. Setting up libjavascriptcoregtk-1.0-0 (1.8.0-0ubuntu2) ... Setting up libwebkitgtk-1.0-common (1.8.0-0ubuntu2) ... Setting up libwebkitgtk-1.0-0 (1.8.0-0ubuntu2) ... Setting up chmsee (1.3.0-2ubuntu2) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: qmail qmail-run Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (1) Setting up qmail (1.06-4) ... The hostname -f command returned: $1 Your system needs to have a fully qualified domain name (fqdn) in order to install the var-qmail packages. Installation aborted. dpkg: error processing qmail (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of qmail-run: qmail-run depends on qmail (>= 1.06-2.1); however: Package qmail is not configured yet. dpkg: error processing qmail-run (--configure): dependency problems - leaving unconfigured Can someone please help me in resolving this issue. The elaboration would be most appreciated since I am very new to this. Thanks, Anshuman Chakraborty

  Read the article

• Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

  - by Ritwik

  I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

  Read the article

• Big data: An evening in the life of an actual buyer

  - by Jean-Pierre Dijcks

  Here I am, and this is an actual story of one of my evenings, trying to spend money with a company and ultimately failing. I just gave up and bought a service from another vendor, not the incumbent. Here is that story and how I think big data could actually fix this (and potentially prevent some of this from happening). In the end this story should illustrate how big data can benefit me (get me what I want without causing grief) and the company I am trying to buy something from. Note: Lots of details left out, I have no intention of being the annoyed blogger moaning about a specific company. What did I want to get? We watch TV, we have internet and we do have a land line. The land line is from a different vendor then the TV and the internet. I have decided that this makes no sense and I was going to get a bundle (no need to infer who this is, I just picked the generic bundle word as this is what I want to get) of all three services as this seems to save me money. I also want to not talk to people, I just want to click on a website when I feel like it and get it all sorted. I do think that is reality. I want to just do my shopping at 9.30pm while watching silly reruns on TV. Problem 1 - Bad links So, I'm an existing customer of the company I want to buy my bundle from. I go to the website, I click on offers. Turns out they are offers for new customers. After grumbling about how good they are, I click on offers for existing customers. Bummer, it goes to offers for new customers, so I click again on the link for offers for existing customers. No cigar... it just does not work. Big data solutions: 1) Do not show an existing customer the offers for new customers unless they are the same => This is only partially doable without login, but if a customer logs in the application should always know that this is an existing customer. But in general, imagine I do this from my home going through the internet service of this vendor to their domain... an instant filter should move me into the "existing customer route". 2) Flag dead or incorrect links => I've clicked the link for "existing customer offers" at least 3 times in under 5 seconds... Identifying patterns like this is easy in Hadoop and can very quickly make a list of potentially incorrect links. No need for realtime fixing, just the fact that this link can be pro-actively fixed across my entire web domain is a good thing. Preventative maintenance! Problem 2 - Purchase cannot be completed Apart from the fact that the browsing pattern to actually get to what I want is poorly designed, my purchase never gets past a specific point. In other words, I put something into my shopping cart and when I want to move on the application either crashes (with me going to an error page) or hangs or goes into something like chat. So I try again, and again and again. I think I tried this entire path (while being logged in!!) at least 10 times over the course of 20 minutes. I also clicked on the feedback button and, frustrated as I was, tried to explain this did not work... Big Data Solutions: 1) This web site does shopping cart analysis. I got an email next day stating I have things in my shopping cart, just click here to complete my purchase. After the above experience, this just added insult to my pain... 2) What should have happened, is a Hadoop job going over all logged in customers that are on the buy flow. It should flag anyone who is trying (multiple attempts from the same user to do the same thing), analyze the shopping card, the clicks to identify what the customers wants, his feedback provided (note: always own your own website feedback, never just farm this out!!) and in a short turn around time (30 minutes to 2 hours or so) email me with a link to complete my purchase. Not with a link to my shopping cart 12 hours later, but a link to actually achieve what I wanted... Why should this company go through the big data effort? I do believe this is relatively easy to do using our Oracle Event Processing and Big Data Appliance solutions combined. It is almost so simple (to my mind) that it makes no sense that this is not in place? But, now I am ranting... Why is this interesting? It is because of $$$$. After trying really hard, I mean I did this all in the evening, and again in the morning before going to work. I kept on failing, But I really wanted this to work... so an email that said, sorry, we noticed you tried to get a bundle (the log knows what I wanted, where I failed, so easy to generate), here is the link to click and complete your purchase. And here is 2 movies on us as an apology would have kept me as a customer, and got the additional $$$$ per month for the next couple of years. It would also lead to upsell on my phone package etc. Instead, I went to a completely different company, bought service from them. Lost money for company A, negative sentiment for company A and me telling this story at the water cooler so I'm influencing more people to think negatively about company A. All in all, a loss of easy money, a ding in sentiment and image where a relatively simple solution exists and can be in place on the software I describe routinely in this blog... For those who are coming to Openworld and maybe see value in solving the above, or are thinking of how to solve this, come visit us in Moscone North - Oracle Red Lounge or in the Engineered Systems Showcase.

  Read the article

• Looking into ASP.Net MVC 4.0 Mobile Development - part 1

  - by nikolaosk

  In this post I will be looking how ASP.Net MVC 4.0 helps us to create web solutions that target mobile devices.We all experience the magic that is the World Wide Web through mobile devices. Millions of people around the world, use tablets and smartphones to view the contents of websites,e-shops and portals.ASP.Net MVC 4.0 includes a new mobile project template and the ability to render a different set of views for different types of devices.There is a new feature that is called browser overriding which allows us to control exactly what a user is going to see from your web application regardless of what type of device he is using.In order to follow along this post you must have Visual Studio 2012 and .Net Framework 4.5 installed in your machine.Download and install VS 2012 using this link.My machine runs on Windows 8 and Visual Studio 2012 works just fine.It will work fine in Windows 7 as well so do not worry if you do not have the latest Microsoft operating system.1) Launch VS 2012 and create a new Web Forms application by going to File - >New Project - > ASP.Net MVC 4 Web Application and then click OKHave a look at the picture below  2) From the available templates select Mobile Application and then click OK.Have a look at the picture below 3) When I run the application I get the mobile view of the page. I would like to show you what a typical ASP.Net MVC 4.0 application looks like. So I will create a new simple ASP.Net MVC 4.0 Web Application. When I run the application I get the normal page view.Have a look at the picture below.On the left is the mobile view and on the right the normal view. As you can see we have more or less the same content in our mobile application (log in,register) compared with the normal ASP.Net MVC 4.0 application but it is optimised for mobile devices. 4) Let me explain how and when the mobile view is selected and finally rendered.There is a feature in MVC 4.0 that is called Display Modes and with this feature the runtime will select a view.If we have 2 views e.g contact.mobile.cshtml and contact.cshtml in our application the Controller at some point will instruct the runtime to select and render a view named contact.The runtime will look at the browser making the request and will determine if it is a mobile browser or a desktop browser. So if there is a request from my IPhone Safari browser for a particular site, if there is a mobile view the MVC 4.0 will select it and render it. If there is not a mobile view, the normal view will be rendered.5) In the  ASP.Net MVC 4.0 (Internet application) I created earlier (not the first project which was a mobile one) I can run it once more and see how it looks on the browser. If I want to view it with a mobile browser I must download one emulator like Opera Mobile.You can download Opera Mobile hereWhen I run the application I get the same view in both the desktop and the mobile browser. That was to be expected. Have a look at the picture below 6) Then I create another version of the _Layout.mobile.cshtml view in the Shared folder.I simply copy and paste the _Layout.cshtml  into the same folder and then rename it to _Layout.mobile.cshtml and then just alter the contents of the _Layout.mobile.cshtml.When I run again the application I get a different view on the desktop browser and a different one on the Opera mobile browser.Have a look at the picture below ?he Controller will instruct the ASP.Net runtime to select and render a view named _Layout.mobile.cshtml when the request will come from a mobile browser.?he runtime knows that a browser is a mobile one through the ASP.Net browser capability provider. Hope it helps!!!

  Read the article

• MSMQ messages using HTTP just won't get delivered

  - by John Breakwell

  I'm starting off the blog with a discussion of an unusual problem that has hit a couple of my customers this month. It's not a problem you'd expect to bump into and the solution is potentially painful. Scenario You want to make use of the HTTP protocol to send MSMQ messages from one machine to another. You have installed HTTP support for MSMQ and have addressed your messages correctly but they will not leave the outgoing queue. There is no configuration for HTTP support - setup has already done all that for you (although you may want to check the most recent "Installation of the MSMQ HTTP Support Subcomponent" section of MSMQINST.LOG to see if anything DID go wrong) - so you can't tweak anything. Restarting services and servers makes no difference - the messages just will not get delivered. The problem is documented and resolved by Knowledgebase article 916699 "The message may not be delivered when you use the HTTP protocol to send a message to a server that is running Message Queuing 3.0". It is unlikely that you would be able to resolve the problem without the assistance of PSS because there are no messages that can be seen to assist you and only access to the source code exposes the root cause. As this communication is over HTTP, the IIS logs would be a good place to start. POST entries are logged which show that connectivity is working and message delivery is being attempted: #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2006-09-12 12:11:29 #Fields: date time s-sitename s-ip cs-method cs-uri-stem cs-uri-query s-port cs-username c-ip cs(User-Agent) sc-status sc-substatus sc-win32-status 2006-09-12 12:12:12 W3SVC1 10.1.17.219 POST /msmq/private$/test - 80 - 10.2.200.3 - 200 0 0 If you capture the traffic with Network Monitor you can see the POST being sent to the server but you also see a response being returned to the client: HTTP: Response to Client; HTTP/1.1; Status Code = 500 - Internal Server Error "Internal Server Error" means we can probably stop looking at IIS and instead focus on the Message Queuing ISAPI extension (Mqise.dll). MSMQ 3.0 (Windows XP and Windows Server 2003) comes with error logging enabled by default but the log files are in binary format - MSMQ 2.0 generated logging in plain text. The symbolic information needed for formatting the files is not currently publicly available so log files have to be sent in to Microsoft PSS.  Although this does mean raising a support case, formatting the log files to text and returning them to the customer shouldn't take long. Obviously the engineer analyses them for you - I just want to point out that you can see the logging output in text format if you want it. The important entries in the log for this problem are: [7]b48.928 09/12/2006-13:20:44.552 [mqise GetNetBiosNameFromIPAddr] ERROR:Failed to get the NetBios name from the DNS name, error = 0xea [7]b48.928 09/12/2006-13:20:44.552 [mqise RPCToServer] ERROR:RPC call R_ProcessHTTPRequest failed, error code = 1702(RPC_S_INVALID_BINDING) which allow a Microsoft escalation engineer to check the MQISE source code to see what is going wrong. This problem according to the article occurs when the extension tries to bind to the local MSMQ service after the extension receives a POST request that contains an MSMQ message. MSMQ resolves the server name by using the DNS host name but the extension cannot bind to the service because the buffer that MSMQ uses to resolve the server name is too small - server names that are exactly 15 characters long will not fit. RPC exception 0x6a6 (RPC_S_INVALID_BINDING) occurs in the W3wp.exe process but the exception is handled and so you do not receive an error message. The workaround is to rename the MSMQ server to something less than 15 characters. If the problem has only just been noticed in a production environment - an application may have been modified to get through a newly-implemented firewall, for example - then renaming is going to be an issue. Other applications may need to be reinstalled or modified if server names are hard-coded or stored in the registry. The renaming may also break a company naming convention where the name is built up from something like location+department+number. If you want to learn more about MSMQ logging then check out Chapter 15 of the MSMQ FAQ. In fact, even if you DON'T want to learn anything about MSMQ logging you should read the FAQ anyway as there is a huge amount of useful information on known issues and the like.

  Read the article

• POP Forums v9 Beta 1 for ASP.NET MVC 3 posted to CodePlex!

  - by Jeff

  As promised, I posted a beta build of my forum app for ASP.NET MVC 3. Get the new goodies here: http://popforums.codeplex.com/releases/view/58228 This is the first beta for the ASP.NET MVC 3 version of POP Forums. It is nearly feature complete, and ready for testing and feedback. For previous release notes, look here, here and here.Check out the live preview: http://preview.popforums.com/ForumsSetup instructions are on the home page of this project. The new hotness in the beta, or what has been done since the last preview: All views converted to use Razor E-mail subscription/notification of new posts New post indicators/mark read buttons Permalinks to posts Jump to newest post (from new post indicators) Recent topics Favorite topics Moderator functions for topics (pin/close/delete, plus move and rename) Search, ported from v8. Not a ton of optimization here, or new unit testing, but the old version worked pretty well User posts (topics the user posted in) Forgot password Vanity items (signatures and avatars) Hide vanity items per user preference Some minor data caching where appropriate A little bit of UI refinement Lots-o-bug fixes Lots-o-unit tests What's next? The plan between now and the next beta is as follows: Continue working through features/tasks, and fix bugs as they're reported Integrate the forum into a real, production site Refine the UI Refactor as much as possible... the code organization is not entirely logical in some places After the second beta, a release candidate will follow, with a real "final" release after that. Subsequent releases should come relatively frequently and without a lot of risk. The trick in building this thing has been that it mostly tossed the previous WebForms version, which was all full of crusties. The time table for this is a little harder to pin down, as day jobs and families will have their effect. Other notes Refactoring will be a priority. As the features of MVC have evolved, so have my desires to use it in a fashion that makes things clear and easy to follow. I don't even know if anyone will ever start mucking around in the code, but on the off chance they do, I'd like what they find to not suck. Other nice-to-haves are builds to target Windows Azure and SQL CE. A nice setup UI would be super too. I think the ASP.NET MVC world has gone long enough without a decent forum.The biggest challenge that I've found is making the forum something that can be dropped in any app. While it does rope its views into an area, areas are mostly just routing details. I haven't thought of a clever way yet to limit dependency injection, for example, to just the forum bits. I mean, everyone should be using Ninject, but how realistic is that? ;)How much time and effort should you spend on POP Forums in its current state? Change is inevitable, but at this point I'm reasonably committed to not changing the database schema. I really think it will stay as-is. All bets are off for the various interfaces throughout the app, but the data should generally resist change. It's not even that different from v8, which was one of the original goals because I didn't want to rewrite SQL or introduce a new ORM or whatever. My point is that if you wanted to build a site around this today, even though it's not entirely functional, I think it's low risk in terms of data loss. I can't vouch for whether or not you know what you're doing.I've been having some chats with people lately about quoting posts, and honestly there has to be something better and straight forward. That continues to be a holy grail of mine, and some day, I hope to find it.Enjoy... it's starting to feel more real every day!

  Read the article

• Rotate a Video 90 degrees with VLC or Windows Live Movie Maker

  - by DigitalGeekery

  Have you ever captured video with your cell phone or camcorder only to discover when you play it back on your computer that the video is rotated 90 degrees? Or maybe you shot it that way on purpose because you preferred portrait style to a landscape view? Before you go straining your neck or flipping your monitor on it’s side to watch your video, we’ll show you a few easier methods. If you simply want to rotate the video while you watch it, we’ll show you how to accomplish that with VLC Media Player. If you want to convert the video so it is rotated permanently, we’ll show you how to do that with Windows Live Movie Maker and output your video as a WMV file. Rotate and Watch a Video in VLC Download, install, and run VLC Media Player. (See download link below)   Open your video file by going to Media  > Open File… and browsing for your file. Or, by just dragging and dropping your video onto the VLC player.   Choose Tools from the Menu bar and select Effects and Filters. On the Video Effects tab, tick the Transform checkbox and choose your degrees of rotation. The video is rotated counter-clockwise, so to rotate clockwise 90 degrees you’ll want to choose Rotate by 270 degrees.   Now you can enjoy your video the way it was intended to be viewed. Rotate and Convert the Video with Windows Live Movie Maker Starting with Windows 7, Windows Movie Maker no longer comes pre-installed with the OS. It’s now part of the Windows Live suite that is available as a separate, free download for Windows 7 and Vista. (Windows XP is not supported) You can find the link to our detailed instruction on how to install Windows Live at the end of the article. To add your video files to Windows Movie Maker, click on Add videos and photos on the Home tab, or drag and drop the video into the blank area on the right side of the application. Next, you’ll need to rotate the video. Staying on the Home tab, click on the Rotate right 90° or Rotate left 90°.   You’ll see your video is now oriented properly on the left.   To save and convert your video to WMV format, click the Movie Maker tab just to the left of the Home tab. Hover your cursor over Save movie, and then select your output settings. You also have the option to burn directly to DVD. Browse for a location to save it and rename the output file if you’d like. Click Save. You’ll be notified when the file is complete. Now you’ll have your video properly oriented in WMV file format.   These are two rather easy ways to accomplish rotating your video. Unfortunately, Windows Live Movie Maker doesn’t give you a lot of  options for output. If you want to output to a file, your only choice is WMV format or DVD. However, previous versions will also allow you to export to AVI. How-To Geek’s Install Windows Live Essentials In Windows 7 Article. Download Windows Live Download VLC Media Player Similar Articles Productive Geek Tips How to Make/Edit a movie with Windows Movie Maker in Windows VistaCreate and Author DVDs in Windows 7Family Fun: Share Photos with Photo Gallery and Windows Live SpacesInstall Windows Live Essentials In Windows 7Add Network Support to Windows Live MovieMaker TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awesome Lyrics Finder for Winamp & Windows Media Player Download Videos from Hulu Pixels invade Manhattan Convert PDF files to ePub to read on your iPad Hide Your Confidential Files Inside Images Get Wildlife Photography Tips at BBC’s PhotoMasterClasses

  Read the article

• SharePoint 2010 Hosting :: SharePoint 2010 Custom Web Template

  - by mbridge

  SharePoint 2010 offers some changes and additions to the SharePoint 2007 approach. Site definitions and publishing providers remain largely the same, but site templates created from the SharePoint UI or SharePoint Designer are now saved to a .WSP file, the same solution deployment packaging file format used for deploying custom SharePoint solutions. Site Templates saved to a .WSP solution file can be imported into Visual Studio for additional customization. Introducing the WebTemplate Feature Element The WebTemplate element, introduced in SharePoint 2010, allows site templates to be defined and deployed as a Feature as part of a solution package. A WebTemplate element feature can be used to deploy site templates in either a Farm or Sandbox solution - without modification. If deployed as a Farm feature and solution, site templates will appear in the site collection provisioning page in Central Administration and can be used to provision new site collections, or within a Site Collection to create sub-sites. If deployed as a Site feature and Sandbox solution, site templates will appear within the site collection to support creating a root site or sub-sites. Creating a new WebTemplate Feature in Visual Studio 2010 In addition to supporting the ability to save and import Site Templates created from the SharePoint UI into Visual Studio for customization, it can also be used to create new site templates from scratch. In the following sample we will walk through how to create a new WebTemplate solution based on  a customized version of the out-of-box Blank Site. 1. Create a new Empty SharePoint Project in Visual Studio 2010. 2. Add a new Empty Element to the project. we like to create folders for each type of element in our solution, so in our sample, we have created a Web Templates folder, and then added the BLANKENT element. NOTE: The Elements folder MUST share the same name as the WebTemplate name property. 3. Open the empty Elements.xml and add the <WebTemplate /> element block. 4. Copy the default.aspx and ONET.XML files from the STS site definition location at 14\TEMPLATES\Site Templates\STS. We will customize the ONET.XML in the next section. Open the properties for each file and set the Deployment Type to ElementFile. This ensures the files are deployed with the Element when included in a Feature. 5. By default a new feature is added to the solution for you automatically when a new element is added to the solution. Rename and edit the feature as appropriate. Select Farm for the scope to deploy the WebTemplate to the entire farm, or Site for a sandboxed solution. Customize the ONET.XML At this point, you have a working WebTemplate solution that will deploy the identical site to the out-of-box Blank Site, however the ONET.XML supporting the STS site definition contains 3 configurations – essentially 3 separate site templates and can be simplified before customizing. In the following sample, we have trimmed the ONET.XML to the essentials for a single Site Template, and added references to the <SiteFeatures /> and <WebFeatures /> elements to include the SharePoint Standard and Enterprise features. We have left the top-level navigation bar, and the default page module intact, but removed all other extraneous markup.

  Read the article

• How to Restore the Real Internet Explorer Desktop Icon in Windows 7

  - by The Geek

  Remember how previous versions of Windows had an Internet Explorer icon on the desktop, and you could right-click it to quickly access the Internet Options screen? It’s completely gone in Windows 7, but a geeky hack can bring it back. Microsoft removed this feature to comply with all those murky legal battles they’ve had, and their alternate suggestion is to create a standard shortcut to iexplore.exe on the Desktop, but it’s not the same thing. We’ve got a registry hack to bring it back. This guest article was written by Ramesh from the WinHelpOnline blog, where he’s got loads of really geeky registry hacks. Bring Back the Internet Explorer Namespace Icon in Windows 7 the Easy Way If you just want the IE icon back, all you need to do is download the RealInternetExplorerIcon.zip file, extract the contents, and then double-click on the w7_ie_icon_restore.reg file. That’s all you have to do. There’s also an undo registry file there if you want to get rid of it. Download the Real Internet Explorer Icon Registry Hack Manual Registry Hack If you prefer doing things the manual way, or just really want to understand how this hack works, you can follow through the manual steps below to learn how it was done, but we’ll have to warn you that it’s a lot of steps. Launch Regedit.exe using the Start Menu search box, and then navigate to the following location: HKEY_CLASSES_ROOT \ CLSID \ {871C5380-42A0-1069-A2EA-08002B30309D} Right-click on the key on the left-hand pane, choose Export, and save it to a .REG file (say, ie-guid.reg) Open up the REG file using Notepad… From the Edit menu, click Replace, and replace every occurrence of the following GUID string {871C5380-42A0-1069-A2EA-08002B30309D} … with a custom GUID string, such as: {871C5380-42A0-1069-A2EA-08002B30301D} Save the REG file and close Notepad, and then double-click on the file to merge the contents to the registry. Either re-open the registry editor, or use the F5 key to reload everything with the new changes (this step is important). Now you can navigate downto the following registry key: HKEY_CLASSES_ROOT \ CLSID \ {871C5380-42A0-1069-A2EA-08002B30301D} \ Shellex \ ContextMenuHandlers \ ieframe Double-click on the (default) key in the right-hand pane and set its data as: {871C5380-42A0-1069-A2EA-08002B30309D} With this done, press F5 on the desktop and you’ll see the Internet Explorer icon that looks like this: The icon appears incomplete without the Properties command in right click menu, so keep reading. Final Registry Hack Adjustments Click on the following key, which should still be viewable in your Registry editor window from the last step. HKEY_CLASSES_ROOT\CLSID\{871C5380-42A0-1069-A2EA-08002B30301D} Double-click LocalizedString in the right-hand pane and type the following data to rename the icon. Internet Explorer Select the following key: HKEY_CLASSES_ROOT\CLSID\{871C5380-42A0-1069-A2EA-08002B30301D}\shell Add a subkey and name it as Properties, then select the Properties key, double-click the (default) value and type the following: P&roperties Create a String value named Position, and type the following data bottom At this point the window should look something like this: Under Properties, create a subkey and name it as Command, and then set its (default) value as follows: control.exe inetcpl.cpl Navigate down to the following key, and then delete the value named LegacyDisable HKEY_CLASSES_ROOT \ CLSID \ {871C5380-42A0-1069-A2EA-08002B30301D} \ shell \ OpenHomePage Now head to the this key: HKEY_LOCAL_MACHINE \ SOFTWARE \ Microsoft \ Windows \ CurrentVersion \ Explorer \ Desktop \ NameSpace Create a subkey named {871C5380-42A0-1069-A2EA-08002B30301D} (which is the custom GUID that we used earlier in this article.) Press F5 to refresh the Desktop, and here is how the Internet Explorer icon would look like, finally. That’s it! It only took 24 steps, but you made it through to the end—of course, you could just download the registry hack and get the icon back with a double-click. Similar Articles Productive Geek Tips Quick Help: Restore Show Desktop Icon in Windows VistaQuick Help: Restore Flip3D Icon in Windows VistaAdd Internet Explorer Icon to Windows XP / Vista DesktopHide, Delete, or Destroy the Recycle Bin Icon in Windows 7 or VistaBuilt-in Quick Launch Hotkeys in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Looking for Good Windows Media Player 12 Plug-ins? Find Out the Celebrity You Resemble With FaceDouble Whoa ! Use Printflush to Solve Printing Problems Icelandic Volcano Webcams Open Multiple Links At One Go

  Read the article

• Clustering for Mere Mortals (Pt2)

  - by Geoff N. Hiten

  Planning. I could stop there and let that be the entirety post #2 in this series.  Planning is the single most important element in building a cluster and the Laptop Demo Cluster is no exception.  One of the more awkward parts of actually creating a cluster is coordinating information between Windows Clustering and SQL Clustering.  The dialog boxes show up hours apart, but still have to have matching and consistent information. Excel seems to be a good tool for tracking these settings.  My workbook has four pages: Systems, Storage, Network, and Service Accounts.  The systems page looks like this:   Name Role Software Location East Physical Cluster Node 1 Windows Server 2008 R2 Enterprise Laptop VM West Physical Cluster Node 2 Windows Server 2008 R2 Enterprise Laptop VM North Physical Cluster Node 3 (Future Reserved) Windows Server 2008 R2 Enterprise Laptop VM MicroCluster Cluster Management Interface N/A Laptop VM SQL01 High-Performance High-Security Instance SQL Server 2008 Enterprise Edition x64 SP1 Laptop VM SQL02 High-Performance Standard-Security Instance SQL Server 2008 Enterprise Edition x64 SP1 Laptop VM SQL03 Standard-Performance High-Security Instance SQL Server 2008 Enterprise Edition x64 SP1 Laptop VM Note that everything that has a computer name is listed here, whether physical or virtual. Storage looks like this: Storage Name Instance Purpose Volume Path Size (GB) LUN ID Speed Quorum MicroCluster Cluster Quorum Quorum Q: 2     SQL01Anchor SQL01 Instance Anchor SQL01Anchor L: 2     SQL02Anchor SQL02 Instance Anchor SQL02Anchor M: 2     SQL01Data1 SQL01 SQL Data SQL01Data1 L:\MountPoints\SQL01Data1 2     SQL02Data1 SQL02 SQL Data SQL02Data1 M:\MountPoints\SQL02Data1       Starting at the left is the name used in the storage array.  It is important to rename resources at each level, whether it is Storage, LUN, Volume, or disk folder.  Otherwise, troubleshooting things gets complex and difficult.  You want to be able to glance at a resource at any level and see where it comes from and what it is connected to. Networking is the same way:   System Network VLAN  IP Subnet Mask Gateway DNS1 DNS2 East Public Cluster1 10.97.230.x(DHCP) 255.255.255.0 10.97.230.1 10.97.230.1 10.97.230.1 East Heartbeat Cluster2   255.255.255.0       West Public Cluster1 10.97.230.x(DHCP) 255.255.255.0 10.97.230.1 10.97.230.1 10.97.230.1 West Heartbeat Cluster2   255.255.255.0       North Public Cluster1 10.97.230.x(DHCP) 255.255.255.0 10.97.230.1 10.97.230.1 10.97.230.1 North Heartbeat Cluster2   255.255.255.0       SQL01 Public Cluster1 10.97.230.x(DHCP) 255.255.255.0       SQL02 Public Cluster1 10.97.230.x(DHCP) 255.255.255.0       One hallmark of a poorly planned and implemented cluster is a bunch of "Local Network Connection #n" entries in the network settings page.  That lets me know that somebody didn't care about the long-term supportabaility of the cluster.  This can be critically important with Hyper-V Clusters and their high NIC counts.  Final page:   Instance Service Name Account Password Domain OU SQL01 SQL Server SVCSQL01 Baseline22 MicroAD Service Accounts SQL01 SQL Agent SVCSQL01 Baseline22 MicroAD Service Accounts SQL02 SQL Server SVC_SQL02 Baseline22 MicroAD Service Accounts SQL02 SQL Agent SVC_SQL02 Baseline22 MicroAD Service Accounts SQL03 (Future) SQL Server SVC_SQL03 Baseline22 MicroAD Service Accounts SQL03 (Future) SQL Agent SVC_SQL03 Baseline22 MicroAD Service Accounts             Installation Account           administrator            Yes.  I write down the account information.  I secure the file via NTFS, but I don't want to fumble around looking for passwords when it comes time to rebuild a node. Always fill out the workbook COMPLETELY before installing anything.  The whole point is to have everything you need at your fingertips before you begin.  The install experience is so much better and more productive with this information in place.

  Read the article

• Add the Vista Style Sidebar Back to Windows 7

  - by Mysticgeek

  If you are moving from Vista to Windows 7, you might miss the Sidebar which was introduced in Vista. Today we take a look at a couple options for getting a Sidebar back in Windows 7. Copy Files from Vista Note: In this example we are using 32-bit versions of Vista and Windows 7. Make sure you are logged in with Administrator credentials. If you have a Vista machine running, we can copy the Windows Sidebar files over to the Windows 7 machine. On the Vista machine navigate to C:\Program Files and copy the Windows Sidebar folder and all of its contents over to a flash drive or network location. On the Windows 7 machine go to C:\Program Files and rename the Windows Sidebar folder to something like Windows Sidebar_old. Now copy the Vista Windows Sidebar folder into C:\Program Files… Now you will have both folders…Windows Sidebar and Windows Sidebar_old in your C:\Program Files folder. Right-click on the desktop and select Gadgets. There you are…the Original Vista Sidebar is back and will act as it did in Vista. Move Sidebar Gadgets Another work around if you don’t have a copy of Vista, you can simply move the Desktop Gadgets you want over to the right side of the screen and they will stay there…no dock needed. Type gadgets into the Search box in the Windows Start Menu and click on Desktop Gadgets. Then drag the included Gadgets you want over to the right side of the screen. Or click on the link to Get more gadgets online to find more. Once you have them where you want, each time you reboot they will still be in the same location. This holds true no matter where you place them on your desktop as well. Install Desktop Sidebar If you want an enhanced sidebar that includes a lot of different features, and don’t have a copy of Vista, you might want to check out Desktop Sidebar Beta (link below). This is a freeware application that works with Windows XP, Vista, and Windows 7. After installation you can access it from the Start Menu… Here is how it will look after you launch it… It includes several pre-installed panels including a clock, Media Player, Search Bar, Slideshow, Messenger, Outlook inbox, Tasks, Quick Launch, Performance…and a lot more. It is highly customizable and allows you to change skins, add various levels of transparency, and a lot more. One caveat with going with Desktop Sidebar is we didn’t find a way to add Windows Gadgets to it (though there might be a plugin for it that we’re not aware of). But there are so many options, you may not mind. However, you can still use the desktop gadgets as you normally would in Windows 7. Believe it or not, some people actually prefer the Vista style Sidebar and would like it back in Windows 7. With these options you can get the Vista Sidebar back if you have a copy of Vista, place the Gadgets on the desktop, or go the freeware route. Download Desktop Sidebar (freeware) Similar Articles Productive Geek Tips Disable Windows Sidebar in VistaHow To Repair Your Crashed or Hanging Vista SidebarApplying Themes To Your Windows Vista SidebarDisable Sidebar / Desktop Gadgets on Windows 7Put AOL Instant Messenger (AIM) In your Windows Sidebar TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 VMware Workstation 7 Acronis Online Backup Ultimate Boot CD can help when disaster strikes Windows Firewall with Advanced Security – How To Guides Sculptris 1.0, 3D Drawing app AceStock, a Tiny Desktop Quote Monitor Gmail Button Addon (Firefox) Hyperwords addon (Firefox)

  Read the article

• Share Files and Folders and Internet between Guest OS and the Host in Hyper-V

  - by Manesh Karunakaran

  For those who are familiar with the VirtualPC, vmWare and VirtualBox environments will be quite irritated to find out that there is no direct way to share files from the Host machine to the Virtualized guest environment. This is a good thing from a CIO perspective because there’s excellent isolation for the virtualized environments this way, but for the developer junkies like us, this is an irritant, especially for those who have nuked their Windows 7 OS and installed Windows Server 2008 R2 for all the the SharePoint friendliness that it offers. Here’s a quick 5 minutes howto on Enabling Shared Folders and Internet Access for the Hyper-V images, for those who are still struggling with this. Step 1: Add a Virtual Network Adapter to your Guest OS For this, shut down the guest machine, go to its settings and add a Virtual Network Adapter as given in the images below     Step 2: Enable Virtual Networking in Hyper-V   Setting this up is very easy. In the Hyper-V Manager, under Actions (right panel), click the Virtual Network Manager. In the Virtual Network Manager in the Create virtual network panel, select Internal and click the Add button.        At this point if you open Control Panel\Network and Internet\Network Connections you will be able to see the new Network Adapter, Now name it to something meaningful other than Network Adapter X. Now you can add this network to each of your virtual machines, but at this point, unless you assign an IP address in each connection, you won't be able to do much.   Step 3: Enable Internet Connection Sharing so that Guest OS’es also can connect to the internet. To enable ICS follow these steps: Click on the network icon in the tray of your host machine and select Network and Sharing Center. From there click Manage network connections. Select the network adapter that you use to access the Internet. Right click it and select Properties. In the properties dialog select the Sharing tab. On this tab check the box that says "Allow other network users..." and then set the Home networking connection to be the network adapter that was created above (now you see why I said to rename it to something useful). Now your virtual machines that have this network connection will automatically get an IP address and will be able to connect to the Internet (provided your internet connection is working). Because each adapter also gets an automatic address you can now share files and folders between your host and your virtual machines which is important since you can't just drag-and-drop files like you can with Virtual PC.   Step 4: Create a Shared Folder in the Host Machine and use it in the Guest machine. Right click on the folder that you want to Share and select ‘Share with\Specific People’ and specify who all can access the share. Open the Guest OS from Hyper V Navigate to Start > Run and type in the Address of the Share (Or Map a Drive to the Share) Bingo! The Share opens!! :)   Now you can share as many files and folders as you want between the host and the guest, and you also have internet access inside the Virtual machines. Hope that helps.   Technorati Tags: Shared folder,Hyper-V,Share Files,Share files and folders between guest and host,Hyper-V Networking,Share Internet Access in Hyper-V,Internet,Files,Shared folders in Hyper-V

  Read the article

• GCC 4.2.1 Compiling on Cygwin(Win7 64bit) for iPhone [closed]

  - by Kenneth Noland

  Hey This is going to take a long while to explain, but the short version is that I am currently attempting to compile the LLVM GCC frontend for ARMv7 to compile apps for the Cortex-A8(iPhone 3GS). I'm running into an error from LD when compiling libgcc(part of the gcc compilation process) that has been driving me mad! The command is this: /usr/llvm-gcc-4.2-2.8.source/build/./gcc/xgcc \ -B/usr/llvm-gcc-4.2_2.8.source/build/./gcc \ -B/usr/local/arm-apple-darwin/bin \ -B/usr/local/arm-apple-darwin/lib \ -isystem /usr/local/arm-apple-darwin/include \ -isystem /usr/local/arm-apple-darwin/sys-include \ -O2 -g -W -Wall -Wwrite-strings -wstrict-prototypes -Wmissing-prototypes -Wold-style-definition -fno-inline -dynamiclib -nodefaultlibs -W1,-dead_strip \ -marm \ -install_name /usr/local/arm-apple-darwin/lib/libgcc_s.1.dylib \ -single_module -o ./libgcc_s.1.dylib.tmp \ -W1,-exported_symbols_list,libgcc/./libgcc.map -compatibility_version 1 -current_version 1.0 -DIN_GCC -DCROSS_DIRECTORY_STRUCTURE -DHAVE_GTHR_DEFAULT -DIN_LIBGCC2 -D__GCC_FLOAT_NOT_NEEDED -Dinhibit_libc \ ... long list of .o files ... \ -lc And the result is typically a lot of undefined references to malloc, free, exit, etc. which typically indicate that libc is not getting compiled in. After going through the list of errors that ld is throwing, I see at the top that it is attempting to pull in /usr/lib/libc.a and complains that it is not the correct platform. Okay, that makes sense, so I spent 5 minutes on google and found an answer. Turns out that if I copy the libSystem.dylib and rename it to libc.dylib, that should solve the problem, but it doesn't. I couldn't find a copy of that file on my phone, so I pulled it directly from the SDK. I then get this strange error: ld64: in /usr/local/arm-apple-darwin/lib/libc.dylib, can't re-map file, errno=22 At this point, I did everything I could think of. I grabbed a fresh copy of my /usr/lib folder from my iphone and confirmed that libSystem.dylib(and libSystem.B.dylib) wasn't there. I unpacked the raw .ipsw package for iOS 4.2.1 and once again, I could not find a copy of libSystem.dylib there either. I unpacked the iPhoneSDK and MacOS SDK and I managed to find a copy of it in both, but that error just kept persisting. I copied libSystem.dylib, libSystem.B.dylib, tried all sorts of combinations of renaming to libc.dylib and still nothing but errors. I can't find a way to get it to recognize the file and link against it. I also tried linking against the libc.a located in the iphone SDK and that didn't work either. I checked what ./xgcc was firing off, and it was my freshly built copy of arm-apple-darwin-ld64 which should be fine. A little bit of background here. I built LLVM+Clang 2.8 with no errors, and I rebuilt the ODCCTools with some light modifications to get it to compile on Cygwin(I'll post my changes in a patch along with a tutorial if I can get this to work). I also grabbed the iphone-dev "includes" and "csu" project and those completed successfully, although there really is no point to them since I can't get it to link against crt0.a. I'm running out of ideas here. Can anyone help me out on this?

  Read the article

• Silverlight Cream for January 13, 2011 -- #1026

  - by Dave Campbell

  In this Issue: András Velvárt, Tony Champion, Joost van Schaik, Jesse Liberty, Shawn Wildermuth, John Papa, Michael Crump, Sacha Barber, Alex Knight, Peter Kuhn, Senthil Kumar, Mike Hole, and WindowsPhoneGeek. Above the Fold: Silverlight: "Create Custom Speech Bubbles in Silverlight." Michael Crump WP7: "Architecting WP7 - Part 9 of 10: Threading" Shawn Wildermuth Expression Blend: "PathListBox: Text on the path" Alex Knight From SilverlightCream.com: Behaviors for accessing the Windows Phone 7 MarketPlace and getting feedback András Velvárt shares almost insider information about how to get some user interaction with your WP7 app in the form of feedback ... he has 4 behaviors taken straight from his very cool SufCube app that he's sharing. Reloading a Collection in the PivotViewer Tony Champion keeps working with the PivotViewer ... this time discussing the fact that you can't Reload or Refresh the current collection from the server ... at least not initially, but he did find one :) Tombstoning MVVMLight ViewModels with SilverlightSerializer on Windows Phone 7 Joost van Schaik takes a shot at helping us all with Tombstoning a WP7 app... he's using Mike Talbot's SilverlightSerializer and created extension methods for it for tombstoning that he's willing to share with us. Windows Phone From Scratch #17: MVVM Light Toolkit Soup To Nuts Part 2 Jesse Liberty is up to Part 17 in his WP7 series, and this is the 2nd post on MVVMLight and WP7, and is digging into behaviors. Architecting WP7 - Part 9 of 10: Threading Shawn Wildermuth is up to part 9 of 10 in his series on Architecting WP7 apps. This episode finds Shawn discussing Threading ... know how to use and choose between BackgroundWorker and ThreadPool? ... Shawn will explain. Silverlight TV 57: Performance Tuning Your Apps In the latest Silverlight TV, John Papa chats with Mike Cook about tuning your Silverlight app to get the performance up there where your users will be happy. Create Custom Speech Bubbles in Silverlight. Michael Crump's already gotten a lot of airplay out of this, but it's so cool.. comic-style callout shapes without using the dlls that you normally would... in other words, paths, and very cool hand-drawn looks on some too... very cool, Michael! Showcasing Cinch MVVM framework / PRISM 4 interoperability Sacha Barber has a post up on CodeProject that demonstratest using Cinch and Prism4 together... handily using MEF since Cinch relies on MEFedMVVM... this is a heck of a post... lots of code, lots of explanations. PathListBox: Text on the path Alex Knight keeps making this PathListBox series better ... this time he is putting text on the path... moving text... too cool, Alex! Windows Phone 7: Pinch Gesture Sample Peter Kuhn digs into the WP7 toolkit and examines GestureListener, pinch events, and clipping... examples and code supplied. How to change the StartPage of the Windows Phone 7 Application in Visual Studio 2010 ? Senthil Kumar discusses how to change the StartPage of your WP7 app, or get the program running if you happen to move or rename MainPage.xaml WP7 Text Boxes – OnEnter (my 1st Behaviour) Mike Hole has a post up about the issue with the keyboard appearing in front of the textbox, and maybe using the enter key to drop it... and he's developed a behavior for that process. WP7 ContextMenu in depth | Part1: key concepts and API WindowsPhoneGeek has some good articles that I haven't posted, but I'll catch up. This one is a nice tutorial on the WP7 Context menu... good explanation, diagrams, and code. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Build Your Own CE6 Kernel

  - by Kate Moss' Big Fan

  The Share Source Program in Windows CE provides many modules in %_WINCEROOT%\Private\ tree, and the kernel is one of them! Although it is not full source of kernel but it is good enough for tracing it, even tweak the kernel. Tracing the kernel and see how it works is lots of fun, but it is fascinated to modify and verify the change you made. So first comes first, where is the source of kernel? It's in your %_WINCEROOT%\private\winceos\COREOS\nk\ And next question will be "How do I build it?", Some of you may say just "build -c" there and it should be good. If you are the owner of kernel and got full source, that is definitely the right answer, but none of them are applied to our case though. So what should I do? Let's dig deeper into the coreos\nk folder, there are a couples of subfolder, CELOG, KDSTUB, KERNEL and etc. KERNEL\ is the main component of kernel.dll, in the other word, most of the modify to kernel is going to happen here. And the good thing is, you could "build -c" in %_WINCEROOT%\private\winceos\COREOS\nk\kernel\ with no error at all. But before doing that, remember to backup eveything you are going to modify, including the source and binaries; remember, this is not something belong to you, and if you didn't restore them back later, it could end up confuse the subsequence QFE updates! Here is the steps Backup the source code, I will suggest the whole %_WINCEROOT%\private\winceos\COREOS\nk\ Backup the binaries in common\oak\lib\, and again if you are not sure which files, backup the whole %_WINCEROOT%\common\oak\lib\ is the safest way. Do whatever modification you want in %_WINCEROOT%\private\winceos\COREOS\nk\kernel\ build -c in %_WINCEROOT%\private\winceos\COREOS\nk\kernel If everything went well so far, you should get a new nkmain.lib,nkmain.pdb, nkprmain.lib and nkprmain.pdb in %_WINCEROOT%\public\common\oak\lib\%_TGTCPU%\%WINCEDEBUG%\ Basically, you just rebuild your new kernel, the rest is to "blddemo clean -q" to have your new kernel SYSGEN'd and include in your OS Image. Or just "set WINCEREL=1" then "sysgen -p common nk nkprof" and "makeimg" if you can't wait another minutes for "blddemo clean -q" Tat sounds good, but some of you may not like the idea to alter any code in private folder, and not to mention how annoying to backup/restore files every time. Better idea? Yes, Microsoft provides a tool SYSGEN_CAPTURE (http://msdn.microsoft.com/en-us/library/ee504678.aspx for detail and usage) to creates Sources files for public drivers that you want to modify and build in your platform directory. In fact, not only public drivers, virtually anything in the %_WINCEROOT%\public\<project name>\cesysgen\makefile can be captured, and of course including kernel. So I am going to introduce a second way to build your own kernel by using SYSGEN_CAPTURE tool. Again the steps Create a folder in your BSP for building kernel, says %_TARGETPLATROOT%\SRC\Kernel. Use "SYSGEN_CAPTURE -p common nk" and then you will get a SOURCES.KERN, you could also "SYSGEN_CAPTURE -p common nkprof" to generate profiler enabled kernel. rename the SOURCE.KERN to SOURCES and copy one of the sample makefile into your kernel directory. For example the one in PRIVATE\WINCEOS\COREOS\NK\KERNEL\NKNORMAL. Copy the source files you want to modify from private\winceos\coreos\nk\kernel\ into your kernel directory. Modifying the SOURCES= macro to the source files you addes in step 4. For example, if you copied the vm.c, it is going to be SOURCES=vm.c Refer to the private\winceos\COREOS\nk\kernel\sources.inc and add macro defines and proper include path in your SOURCES file. "set WINCEREL=1", "build -c" in your kernel directory and "makeimg", voila! Here is an example for the MACROS you need to add in x86 Here are the macros for x86 CDEFINES=$(CDEFINES) -DIN_KERNEL -DWINCEMACRO -DKERN_CORE # Machine independent defines CDEFINES=$(CDEFINES) -DDBGSUPPORT _COREOSROOT=$(_WINCEROOT)\private\winceos\coreos INCLUDES=$(_COREOSROOT)\inc;$(_COREOSROOT)\nk\inc !IFDEF DP_SETTINGS CDEFINES=$(CDEFINES) -DDP_SETTINGS=$(DP_SETTINGS) !ENDIF ASM_SAFESEH=1 CDEFINES=$(CDEFINES) -Gs100000 -DENCODE_GS_COOKIE

  Read the article

• Customize SharePoint list using InfoPath2010 form Part4

  - by ybbest

  Customize SharePoint list using InfoPath2010 form Part1 Customize SharePoint list using InfoPath2010 form Part2 Customize SharePoint list using InfoPath2010 form Part3 In this post, I’d like to show you how to create print functionality in InfoPath for SharePoint list. The print functionality is provided out of box in InfoPath form library; however it is not available in SharePoint list. Here are the steps to create the print functionality.You can download the new form here. 1. Create print page in the list by first copy and paste the displayifs.aspx and rename the file to Printifs.aspx. 2. Open the page in the SharePoint designer and copy the following javascript to the PlaceHolderTitleAreaClass ContentPlaceHolder. <script type="text/javascript"> $(document).ready(function(){ $("[id^='Ribbon']").hide(); $(".s4-title").hide(); $("[id='s4-leftpanel']").hide(); $("[id='s4-ribbonrow']").hide(); $("[id='s4-titlerow']").hide(); $("[id='s4-titlerow']").css("height", "0px"); $("body").css("background-color", "white"); $("body").css("zoom", "135%"); $("[id='MSO_ContentTable']").css("margin-left", "0px"); $("[id='MT-BodyContent']").css("width", "900px"); $(".MT-BodyArea").css("width", "900px"); $("[id='MT-Layout']").css("width", "900px"); $(".ms-bodyareacell").css("width", "900px"); $(".s4-wpTopTable").css("border", "none"); $("[id$='XmlFormView']").css("margin-left", "-80px"); $("body").css("margin-top", "-30px"); $(":contains('CAPEX')").css("border", "5px solid #FFCC00"); window.print(); }); </script> 3. Open InfoPath form for the list and create a field called PrintLink 4. Set the default value of printLink that points to the print page I just created before with the query string id.You can download the formula for the default value here. 5. Add a new image that looks like Print button on the display view, then I can set the url to the Print link Field. (The reason I did not use button is that you cannot set the navigate url for the button). 6.Set the url of the image to the PrintLInk field. 7.Next , create the print view. 8. Copy the contents from the display view to print view 9. Finally, go to the printifs.aspx and edit the InfoPath web part to set the view to PrintView. 9. Republish you form you will see the form as shown below 10. If you click the Print button, you will see the print page and print dialog,you can also add the company logo in the print page using css as well. 11.To deploy the customization,you can use the backup and restore content database approach , you can get more details from my previous blog post here.

  Read the article

• DAC pack up all your troubles

  - by Tony Davis

  Visual Studio 2010, or perhaps its apparently-forthcoming sister, "SQL Studio", is being geared up to become the natural way for developers to create databases. Central to this drive is the introduction of 'data-tier application components', or DACs. Applications are developed as normal but when it comes to deployment, instead of supplying the DBA with a bunch of scripts to create the required database objects, the developer creates a single DAC Package ("DAC Pack"); a zipped XML file containing all the database objects needed by the application, along with versioning information, policies for deployment, and so on. It's an intriguing prospect. Developers can work on their development database using their existing tools and source control, and then package up the changes into a single DACPAC for deployment and management. DBAs get an "application level view" of how their instances are being used and the ability to collectively, rather than individually, manage the objects. The DBA needing to manage a large number of relatively small databases can use "DAC snapshots" to get a quick overview of what has changed across all the databases they manage. The reason that DAC packs haven't caused more excitement is that they can only be pushed to SQL Server 2008 R2, and they must be developed or inspected using Visual Studio 2010. Furthermore, what we see right now in VS2010 is more of a 'work-in-progress' or 'vision of the future', with serious shortcomings and restrictions that render it unsuitable for anything but small 'non-critical' departmental databases. The first problem is that DAC packs support a limited set of schema objects (corresponding closely to the features available on 'Azure'). This means that Service Broker queues, CLR Objects, and perhaps most critically security (permissions, certificates etc.), are off-limits. Applications that require these objects will need to add them via a post-deployment TSQL script, rather defeating the whole idea. More worrying still is the process for altering a database with a DAC pack. The grand 'collective' philosophy, whereby a single XML file can be used for deploying and managing builds and changes, extends, unfortunately, to database upgrades. Any change to a database object will result in the creation of a new database, copying the data from the old version, nuking the previous one, and then renaming the new one. Simple eh? The problem is that even something as trivial as adding a comment to a stored procedure in a 5GB database will require the server to find at least twice as much space, as well sufficient elbow-room in the transaction log for copying the largest table. Of course, you'll need to take the database offline for the full course of the deployment, which is likely to take a long time if there is a lot of data. This upgrade/rename process breaks the log chain, makes any subsequent full restore operation highly complicated, and will also break log shipping. As with any grand vision, the devil is always in the detail. It's hard to fathom why Microsoft hasn't used a SQL Compare-style approach to the upgrade process, altering a database with a change script, and this will surely be adopted in the near future. Something had to be in place for VS2010, but right now DAC packs only make sense for Azure. For this, they're cute, but hardly compelling. Nevertheless, DBAs would do well to get familiar with VS 2010 and DAC packs. Like it or not, they're both coming. Cheers, Tony.

  Read the article

< Previous Page | 388 389 390 391 392 393 394 395 396 397 398 399  | Next Page >