Search Results

Search found 21098 results on 844 pages for 'model import'.

Page 393/844 | < Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >

• Configuring ZenOSS to monitor CPU load

  - by Tom

  I'm trying test out monitoring tools for a network at work with a coworker but neither of us have ever used an sort of monitoring tools before. Currently we are experimenting with ZenOSS and having some difficulties. We want to populate our CPU load graphs because that is one of the primary feature we are looking for in our monitoring tools but we have been unable to populate the graphs with data. So far we have installed the wmipreformance, sqldatasource, wmidatasource, snmpperformance(simple) zenpacks and the machine we are trying to monitor is running Windows XP. We have tried to model the device and everything seems to run and we've tride to add data points to graphs but the only options we recieve for graphs are CPU and Memory. We are able to monitor services, ZenOSS recognizes the make and model of the processor, RAM, and Harddrive and is even giving us metrics on available storage but again, we are looking for performance metrics such as CPU load and Memory utilization. I realize I probably didn't provide a lot of information but that is because we don't have a very good idea of what we are doing and can't find instruction either on the ZenOSS homepage or forums to monitor CPU load. If someone could give us step by step instruction on how to set up CPU load monitoring that would probably be more beneficial to us than a diagnostic of our current setup, but regardless, if I left any important information out and you need it to answer the question, please let me know. Thank you.

  Read the article

• Thecus N5200, disk has dropped out of RAID5

  - by Anders Ekdahl

  We have a Thecus 5200 NAS here at work with five WD Caviar Black 2TB disks in a RADI5 array. Yesterday, disk 4 dropped out of the array, and in the NAS web interface there's a warning about the RAID array being "degraded". When I go into Storage - Disks, disk 1 and 4 has a warning next to them. When I click on the warnings, this information about the disks are displayed: Tray Number 4 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 34 Reallocated Sector Count 66 Current Pending Sector 1447 Raw Read Error Rate 61 Seek Error Rate 0 Hardware ECC Recovered N/A Tray Number 1 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 32 Reallocated Sector Count 0 Current Pending Sector 1465 Raw Read Error Rate 0 Seek Error Rate 0 Hardware ECC Recovered N/A I'm not really an expert on either disks or RAID arrays. Does this indicate that the fourth disk is damaged, and needs to be replaced? And what about disk number one? It has a warning, but it's still in the array. Is it safe to add the fourth disk back into the array as a spare? I can't find any way to add it back as a it were before.

  Read the article

• Correct MySQL username/password, but getting Access Denied error when run from script

  - by Nick

  I'm currently trying to run the following command from within a shell script. /usr/bin/mysql -u username -ppassword -h localhost database It works perfectly fine when executed manually, and not from within a script. When I try to execute a script that contains that command, I get the following error: ERROR 1045 (28000) at line 3: Access denied for user 'username'@'localhost' (using password: YES) I literally copied and pasted the working command into the script. Why the error? As a sidenote: the ultimate intent is to run the script with cron. EDIT: Here is a stripped down version of my script that I'm trying to run. You can ignore most of it up until the point where it connects to MySQL around line 19. #!/bin/sh #Run download script to download product data cd /home/dir/Scripts/Linux /bin/sh script1.sh #Run import script to import product data to MySQL cd /home/dir/Mysql /bin/sh script2.sh #Download inventory stats spreadsheet and rename it cd /home/dir /usr/bin/wget http://www.url.com/file1.txt mv file1.txt sheet1.csv #Remove existing export spreadsheet rm /tmp/sheet2.csv #Run MySQL queries in "here document" format /usr/bin/mysql -u username -ppassword -h localhost database << EOF --Drop old inventory stats table truncate table table_name1; --Load new inventory stats into table Load data local infile '/home/dir/sheet1.csv' into table table_name1 fields terminated by ',' optionally enclosed by '"' lines terminated by '\r\n'; --MySQL queries to combine product data and inventory stats here --Export combined data in spreadsheet format group by p.value into outfile '/tmp/sheet2.csv' fields terminated by ',' optionally enclosed by '"' lines terminated by '\r\n'; EOF EDIT 2: After some more testing, the issue is with the << EOF that is at the end of the command. This is there for the "here document". When removed, the command works fine. The problem is that I need << EOF there so that the MySQL queries will run.

  Read the article

• Which events specifically cause Windows 2008 to mark a SAN volume offline?

  - by Jeremy

  I am searching for specific criteria/events that will cause Windows 2008 to mark a SAN volume as offline in disk management, even though it is connected to that SAN volume via FC or iSCSI. Microsoft states that "A dynamic disk may become Offline if it is corrupted or intermittently unavailable. A dynamic disk may also become Offline if you attempt to import a foreign (dynamic) disk and the import fails. An error icon appears on the Offline disk. Only dynamic disks display the Missing or Offline status." I am specifically wondering if, on the SAN, changing the path to the disk (such as the disk being presented to the host via a different iSCSI target IQN or a different LUN #) would cause a volume to be offlined in disk management. Thanks! Edit: I have already found two reasons why a disk might be set offline, disk signature collisions and the SAN disk policy. Bounty would be awarded to someone who can find further documented reasons related to changes in the volume's path. Disk signature collisions: http://blogs.technet.com/b/markrussinovich/archive/2011/11/08/3463572.aspx SAN disk policy: http://jeffwouters.nl/index.php/2011/06/disk-offline-with-error-the-disk-is-offline-because-of-a-policy-set-by-an-administrator/

  Read the article

• How to clone MySQL DB? Errors with CREATE VIEW/SHOW VIEW privileges

  - by user38071

  Running MySQL 5.0.32 on Debian 4.0 (Etch). I'm trying to clone a WordPress MySQL database completely (structure and data) on the same server. I tried doing a dump to a .sql file and an import into a new empty database from the command line, but the import fails with errors saying the user does not have the "SHOW VIEW" or "CREATE VIEW" privilege. Trying it with PHPMyAdmin doesn't work either. I also tried doing this with the MySQL root user (not named "root" though) and it shows an "Access Denied" error. I'm terribly confused as to where the problem is. Any pointers on cloning a MySQL DB and granting all privileges to a user account would be great (specifically for MySQL 5.0.32). The SHOW GRANTS command for the existing user works (the one who has privileges over the source database). It shows that the user has all privileges granted. I created a new user and database. Here's what I see with the grant commands. $ mysql -A -umyrootaccount --password=myrootaccountpassword mysql> grant all privileges on `newtarget_db`.* to 'newtestuser'@'localhost'; ERROR 1044 (42000): Access denied for user 'myrootaccount'@'localhost' to database 'newtarget_db' mysql> grant all privileges on `newtarget_db`.* to 'existingsourcedbuser'@'localhost'; ERROR 1044 (42000): Access denied for user 'myrootaccount'@'localhost' to database 'newtarget_db'

  Read the article

• SQL Error (1064) when importing data from SQL file

  - by mejpark

  I have a MySQL database, which was originally set up with the default latin1 character set and latin1_swedish_ci collation. I was using the database like this for sometime, until I noticed strange characters on my production web site, which is powered by a database exported from my development machine. At this point, I changed the default character set of the database and tables to utf8 and the collation to utf8_unicode_ci, converted the latin1 data inside each table to utf8 (using the 'convert data' option) and exported the database as a single SQL file using HeidiSQL. When the resulting SQL file is opened in Notepad++, several characters are rendered incorrectly. For example, en dashes (-) are displayed as – and e with accent (é) are displayed as é. I changed the encoding of the file from ANSI to UTF-8 (using the encoding menu option in Notepad++) and the offending characters are rendered correctly. I saved the new utf8-encoded SQL file and attempted to import the contents into the MySQL database on my production server. The import process fails with following error: /* SQL Error (1064): You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near '?# -------------------------------------------------------- # Host: ' at line 1 */ /* Error with snippets directory: The specified path was not found */ The head of the SQL file: # -------------------------------------------------------- # Host: 127.0.0.1 # Server version: 5.1.33-community # Server OS: Win32 # HeidiSQL version: 6.0.0.3773 # Date/time: 2011-04-20 09:48:36 # -------------------------------------------------------- It chokes on the first line of the file, which is commented out. Why is this happening? I didn't have a problem loading data from SQL files until I changed the character set and collation of the database. I came up with an ugly workaround to this problem by performing following steps: Export database as single SQL file using HeidiSQL Open resulting file in Notepad++ and convert from ANSI to UTF-8 encoding Create new empty file in Notepad++, paste in UTF-8 and save file normally What am I missing here?

  Read the article

• Asus K50I sound issues

  - by MrStatic

  I have an Asus K50IJ (Bestbuy) laptop and have issues with my sound. Speakers themselves work fine but when I plug into the headphone jack it auto mutes the front channel and no sounds comes out of either the speakers or the headphones. If I then unmute the channel I get sound from both the speakers and the headphones. alsamixer shows the Headphone channel as all grayed out. /etc/modprobe.d/alsa-base.conf I have tried snd-hda-intel model="asus-laptop" and snd-hda-intel model="asus" In Sound Preferences I have gone to output and changed the Connector to 'Analog Headphones' that results in no sound from either speakers or headphones. As one forum suggested I tried to comment out blacklist snd_pcsp in the blacklist.conf which resulted in no change. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Santa Cruz Operation Device 1043 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at fe9f4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel

  Read the article

• Celery daemon as a Ubuntu service does not consume tasks while running from terminal does

  - by Guy

  On Ubuntu 11.10, I have to issue python tasks from django using celery. I'm currently testing on the same machine but eventually the celery worker should run on a remote machine. django uses the following settings: BROKER_HOST = "127.0.0.1" BROKER_PORT = 5672 BROKER_VHOST = "/my_vhost" BROKER_USER = "celery" BROKER_PASSWORD = "celery" I can also see my task queued in http://localhost:55672/#/queues the celery daemon uses the following configuration (celeryconfig.py): BROKER_HOST = "127.0.0.1" BROKER_PORT = 5672 BROKER_USER = "celery" BROKER_PASSWORD = "celery" BROKER_VHOST = "/my_vhost" CELERY_RESULT_BACKEND = "amqp" import os import sys sys.path.append(os.getcwd()) CELERY_IMPORTS = ("tasks", ) running celeryd -l info works well and now I want to run it as a service. I've followed the instructions from http://ask.github.com/celery/cookbook/daemonizing.html and now I'm trying to run it using: sudo /etc/init.d/celeryd start But the message is not being consumed, no error in the celery log either. /etc/default/celeryd CELERYD_NODES="w1" CELERYD_CHDIR="/path/to/django/project" CELERYD_OPTS="--time-limit=300 --concurrency=1" CELERY_CONFIG_MODULE="celeryconfig" # %n will be replaced with the nodename. CELERYD_LOG_FILE="/var/log/celery/%n.log" CELERYD_PID_FILE="/var/run/celery/%n.pid" # Workers should run as an unprivileged user. CELERYD_USER="celery" CELERYD_GROUP="celery" I've also created user celery in Ubuntu not sure if its necessary. Any help will be appreciated, Thanks, Guy

  Read the article

• VT-x not enabled on 2010 Mac Pro

  - by BlindingDawn

  To start I had a Hackintosh as per the instructions from Lifehacker.com before and moved everything to a new 2010 8 Core Mac Pro. I opted for a restore from the time machine backup rather than using the migration assistance. I believe this may have caused more problems but one in particular is the lack of VT-x support. When I checked Parallels Desktop under "Host Hardware" information, I get the following that shows that VT-x isn't enabled. <Cpu dyn_lists=""> <Number>16</Number> <Model>Intel(R) Xeon(R) CPU E5620 @ 2.40GHz</Model> <Mode>1</Mode> <Speed>2400</Speed> <VtxEnabled>0</VtxEnabled> <VtxMode>1</VtxMode> 1) Does Parallels Desktop support using VT-x? 2) Does this setting show that my VT-x isn't enabled? 3) Is there a way of fixing it so that it is enabled? 4) Is there a way of using my Time Machine backup as if I'm doing a restore using migration assistance and just restore the files and settings?

  Read the article

• Node.js Build failed: -> task failed (error#2)?

  - by Richard Hedges

  I'm trying to install Node.js on my CentOS server. I run ./configure and it runs perfectly fine. I then run the 'make' command and it produces the following: [5/38] libv8.a: deps/v8/SConstruct - out/Release/libv8.a /usr/local/bin/python "/root/node/tools/scons/scons.py" -j 1 -C "/root/node/out/Release/" -Y "/root/node/deps/v8" visibility=default mode=release arch=ia32 toolchain=gcc library=static snapshot=on scons: Reading SConscript files ... ImportError: No module named bz2: File "/root/node/deps/v8/SConstruct", line 37: import js2c, utils File "/root/node/deps/v8/tools/js2c.py", line 36: import bz2 Waf: Leaving directory `/root/node/out' Build failed: - task failed (err #2): {task: libv8.a SConstruct - libv8.a} make: * [program] Error 1 I've done some searching on Google but I can't seem to find anything to help. Most of what I've found is for Cygwin anyway, and I'm on CentOS 4.9. Like I said, the ./configure went through perfectly fine with no errors, so there's nothing there that I can see. EDIT I've got a little further. Now I just need to upgrade G++ to version 4 (or higher). I tried yum update gcc but no luck, so I tried yum install gcc44, which resulted in no luck either. Has anyone got any ideas as to how I can update G++?

  Read the article

• Deploying a Django application in a virtual Ubuntu Server

  - by mfsaint

  I have a virtualbox machine running Ubuntu Server 10.04LTS. My intention is to this machine to work like a VPS, this way I can learn and prepare for when I get a VPS service. Apache+mod_wsgi for deploying the Django app seems the right choice to me. I have the domain (marianofalcon.com.ar) but nothing else, no DNS. The problem is that I'm pretty lost with all the deployment stuff. I know how to configure mod_wsgi(with the django.wsgi file) and apache(creating a VirtualHost). Something is missing and I don't know what it is. I think that I lack networking skills ant that's the big problem. Trying to host the app on a virtualbox adds some difficulty because I don't know well what IP to use. This is what I've got: file placed at: /etc/apache2/sites-available: NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] ServerName www.my-domain.com ServerAlias my-domain.com Alias /media /path/to/my/project/media DocumentRoot /path/to/my/project WSGIScriptAlias / /path/to/your/project/apache/django.wsgi ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined </VirtualHost> django.wsgi file: import os, sys wsgi_dir = os.path.abspath(os.path.dirname(__file__)) project_dir = os.path.dirname(wsgi_dir) sys.path.append(project_dir) project_settings = os.path.join(project_dir,'settings') os.environ['DJANGO_SETTINGS_MODULE'] = 'myproject.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler()

  Read the article

• Printer spooler service stop running when sent print job

  - by Hanan N.

  Every time i am sending a print job to the printer, i am don't get any response from the printer, and at the printer job list at the status of the job, i see that there was an Error, but it don't give me any clue on what could be the problem. After some investigation i found that every time that i send the print job to the printer the printer spooler service stops to run, then after a second or two it start again (i think that this behavior is related to the printer spooler settings to rerun it self after it stops). Things that i have tried so far: Remove and Install again the Driver. After removing the driver, i have removed the unnecessary registry keys according to this article from Microsoft, these are: Rename all files and folders in: c:\windows\system32\spool\drivers\w32x86 Remove anything but Drivers Print and Processors: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environment\Windows NT x86 Remove anything in here: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors but: BJ Language Monitor Local Port Microsoft Document Imaging Writer Monitor Microsoft Shared Fax Monitor Standard TCP/IP Port USB Monitor WSD Port Disconnect and Reconnect the Printer. Clean the computer from Viruses & Spywares. Currently i am stuck, i have no more things to try, if anybody know about any kind of solution please let me know about it. Since i am want to keep this post as general problem that relate to the printer spooler, and not just my particular problem, i didn't included inside the windows version & the printer model, they are (although i think that it isn't relate just for that particular model): Windows 7 32bit, HP Officejet 4500 G510g-m (connect to the computer via USB). Thanks.

  Read the article

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• Can My Personal GMail Query A Remote LDAP Server?

  - by Maarx

  I have a personal GMail account, from which I frequently send e-mail to a great many various users of a specific business. The corporation has been kind enough to provide me with the credentials to access their LDAP server, with which I would like my GMail web client to be able to auto-complete partial addresses or names for which that LDAP server has an entry. Is there any way I can get a personal GMail account (or it's corresponding entire Google account) account to incorporate an LDAP server into it's Contacts? If I cannot get it to query dynamically and on-demand, is there an idiot-proof way (assuming the client permits, which they may not) to query the LDAP server for it's entire database, save it, and bulk import it to GMail? Perhaps, even, something I could set to repeat periodically (weekly, perhaps), without human interaction? If I did the latter, I assume it would be trivial to import all of these contacts under a single category that could be easily manipulated from within the GMail web-based client. I have been a staunch user and supporter of the GMail web-based client since it's instantiation, but this one is kind of a deal-breaker for me. If it's impossible, what do you suggest I do?

  Read the article

• Enable SSL with Jetty 8

  - by Jerec TheSith

  I received certificates from GoDaddy an I'm trying to enable SSL with Jetty but receive an error 107 SSL protocol error when connecting to https://server.com:8443 I generated the keystore using these commands : keytool -keystore keystore -import -alias gd_bundle -trustcacerts -file gd_bundle.crt keytool -keystore keystore -import -alias server.com -trustcacerts -file server.com.crt and placed it in /opt/jetty/etc/ And used the following configuration in jetty.xml : <Call name="addConnector"> <Arg> <New class="org.eclipse.jetty.server.ssl.SslSelectChannelConnector"> <Arg> <New class="org.eclipse.jetty.http.ssl.SslContextFactory"> <Set name="keyStore"><SystemProperty name="jetty.home" default="."/>/etc/keystore</Set> <Set name="keyStorePassword">**password1**</Set> <Set name="keyManagerPassword">**password1**</Set> <Set name="trustStore"><SystemProperty name="jetty.home" default="."/>/etc/keystore</Set> <Set name="trustStorePassword">**password1**</Set> </New> </Arg> <Set name="port">8443</Set> <Set name="maxIdleTime">30000</Set> <Set name="Acceptors">2</Set> <Set name="statsOn">false</Set> <Set name="lowResourcesConnections">20000</Set> <Set name="lowResourcesMaxIdleTime">5000</Set> </New> </Arg> </Call> Am I missing something in jetty's configuration ?

  Read the article

• computer freezes but music continues

  - by Danny

  Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

  Read the article

• How can I stop Excel from eating my delicious CSV files and excreting useless data?

  - by atroon

  I have a database which tracks sales of widgets by serial number. Users enter purchaser data and quantity, and scan each widget into a custom client program. They then finalize the order. This all works flawlessly. Some customers want an Excel-compatible spreadsheet of the widgets they have purchased. We generate this with a PHP script which queries the database and outputs the result as a CSV with the store name and associated data. This works perfectly well too. When opened in a text editor such as Notepad or vi, the file looks like this: "Account Number","Store Name","S1","S2","S3","Widget Type","Date" "4173","SpeedyCorp","268435459705526269","","268435459705526269","848 Model Widget","2011-01-17" As you can see, the serial numbers are present (in this case twice, not all secondary serials are the same) and are long strings of numbers. When this file is opened in Excel, the result becomes: Account Number Store Name S1 S2 S3 Widget Type Date 4173 SpeedyCorp 2.68435E+17 2.68435E+17 848 Model Widget 2011-01-17 As you may have observed, the serial numbers are enclosed by double quotes. Excel does not seem to respect text qualifiers in .csv files. When importing these files into Access, we have zero difficulty. When opening them as text, no trouble at all. But Excel, without fail, converts these files into useless garbage. Trying to instruct end users in the art of opening a CSV file with a non-default application is becoming, shall we say, tiresome. Is there hope? Is there a setting I've been unable to find? This seems to be the case with Excel 2003, 2007, and 2010.

  Read the article

• 85 Hz on old/new driver looks the same like 75 Hz on previous one?

  - by jon

  I have old philips 107T5 CRT and Nvidia graphics card. I used old Nvidia driver (but it wasn't 'legacy' one when I installed it) for few years but recently I decided to install other Linux distribution. I used 75 Hz refresh rate and 1024x768 resolution on my previous distribution. After I installed the new distribution I had to install a Nvidia driver so I downloaded one from the Nvidia site (this time only legacy supported my card so I downloaded legacy and installed it). It wasn't automatically updating xorg.conf but I had my previous xorg.conf copy and I used it. When I run X I could only choose 85 and 75 Hz, 85 was checked as default. And now what shocks me: that default 85 Hz looks identically like 75 Hz on previous driver looked (at least to me). I tried 75 Hz out of curiosity and it's too bright, hurts, etc. But on the previous driver 75 Hz wasn't hurting my eyes. Why is it different? It's the same number after all, so it should always give the same results, right? That's my first question. Second question: Is 85 Hz OK for that monitor model? Would it break it? I tried to find the optimal refresh rate for this model but couldn't find it.

  Read the article

• Dealing with upgrade of libevent on Amazon AWS

  - by Dreen

  I am building an application (in Python) on Amazon EC2 that has a following dependency chain: gevent-websocket ---> gevent ---> libevent The last one (libevent) got upgraded on Sunday and my server is now generating this error: (...) File "/usr/lib/python2.6/site-packages/gevent-0.13.7-py2.6-linux-x86_64.egg/gevent/__init__.py", line 41, in <module> from gevent import core ImportError: libevent-1.4.so.2: cannot open shared object file: No such file or directory Not wanting to spend much time on the issue, I tried to mitigate it by creating a symlink to an always-recent version: $ sudo ln -s /usr/lib64/libevent.so /usr/lib64/libevent-1.4.so.2 But it didn't quite work: (...) File "/usr/lib/python2.6/site-packages/gevent-0.13.7-py2.6-linux-x86_64.egg/gevent/__init__.py", line 41, in <module> from gevent import core ImportError: /usr/lib/python2.6/site-packages/gevent-0.13.7-py2.6-linux-x86_64.egg/gevent/core.so: undefined symbol: current_base I am a bit stumped as to how to proceed. Should I create more symlinks? To what? Or is there a better way to solve this problem... PS. For the record I am using Amazon AMI.

  Read the article

• Can a OS be copied from one hard drive to another and still boot?

  - by AlexMorley-Finch

  Background My computer gets stuck on the make and model screen after the BIOS screen, aka the Toshiba screen. After some research I've realized that the problem is the hard drive. I'm using an old 250gb model that USED to be used for backup purposes, however I loaded windows 7 ultimate onto it This hard drive has trouble getting up to full RPM therefore cannot boot correctly until its warmed up. meaning that my pc needs to be restarted several times before it boots (once it took my 13 reboots to get my pc on!) From my research its either that, or lack of power supply, and I've tried multiple PSUs. Question I have my OS and all my files on this 250gb HDD... If I were to literally open the explorer, and copy EVERYTHING (including hidden files obviously) from this 250gb, to a spare 500gb I've got knocking about... Will it boot if I just copy everything? I cannot be bothered to load another OS onto my PC so if there is a way I can just copy the existing one over from one HDD to another and have it boot normally. This would be epic! I've heard about HDD cloning software. But before I purchase and/or download this software, I need to know if i can just copy the OS over through the windows explorer

  Read the article

• Second CPU missing of Dual Core

  - by Zardoz

  My Lenovo T61 has a dual core CPU. I just noticed that under Ubuntu 10.10 only one CPU is recognized. I know that once both CPUs worked. Not sure since when the second CPU is missing. Maybe since the last kernel update. Currently I am using linux-image-2.6.35-23-generic (for x86_64). What can I do to enable the second CPU again? Here the ouput of /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping : 6 cpu MHz : 800.000 cache size : 3072 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 4189.99 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: Any help is welcome. I really need that CPU power for my work here.

  Read the article

• How do I use command line and wmctrl to make a window larger than the screen to get a huge screenshot?

  - by Mnebuerquo

  I use a program which makes a large image which I have to scroll to view. The program has no way to save the image, and I have no access to the source to modify it. The only way I have to get the image from the program is by screenshot. My goal is to save the full size image without having to piece together individual screenshots. I'm using this script to try taking a screenshot: #!/bin/bash window=$(wmctrl -l | grep "Program$" | awk '{print $1}') wmctrl -v -i -r $window -e '0,0,0,6030,5828' wmctrl -i -a $window import -window $window ~/Desktop/screenshot.png This uses wmctrl to get the window id ($window) for a window named "Program". It then tries to resize the window to the desired dimensions. It uses imagemagick (import) to save a screenshot.png on the user's Desktop. All of this works except the resize step. I can resize the window using wmctrl -r -e, but sizes greater than the screen size don't work. I'm using Ubuntu 10.04 and the Gnome Desktop. I run two monitors, but I've tried this with one of them disabled. Is there a way to resize the window larger than my screen to get a huge screenshot?

  Read the article

• Verification of downloaded package with rpm

  - by moooeeeep

  I wanted to install a package on CentOS 6 via rpm (e.g., the current epel-release). EDIT: Of course I would always prefer the installation via yum but somehow I failed to get that specific package installed using this normal approach. As such, the EPEL/FAQ recommends Version 2. As I'm downloading the package through an insecure channel (http) I wanted to make sure that the integrity of the file is verified using information that is not provided with the downloaded file itself. Is this especially true for all of these approaches? I've seen various approaches to this on the internet: Version 1 rpm -ivh http://dl.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-7.noarch.rpm Version 2 rpm -Uvh http://dl.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-7.noarch.rpm Version 3 wget http://dl.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-7.noarch.rpm rpm --import https://fedoraproject.org/static/0608B895.txt rpm -K epel-release-6-7.noarch.rpm rpm -i epel-release-6-7.noarch.rpm I do not know rpm very well, so I wondered how they might differ? My guess (after reading the manpage) is that the first should only be used when the package is previously not installed, the second would additionally remove previous versions of the package after installation, the first two omit some verification steps before the actual installation that are done by rpm -K. So my main questions at this point are Are my guesses correct or am I missing something? Is the rpm --import ... implicitly done for the first two approaches as well, and if not, isn't it necessary to do so after all? Are these additional checks performed by rpm -K ... any relevant? What is the best (most secure, most reliable, most maintainable, ...) way of installing packages via rpm in general?

  Read the article

• Mercurial hook fails on Windows

  - by Nick Hodges

  I am trying to use the headcount hook (https://bitbucket.org/dgc/headcount/overview) with my main develop repository. I pulled the code and placed it in C:\Python26\Lib\site-packages. I made the following entries into my hgrc file: [hooks] pretxnchangegroup.headcount = python:headcount.headcount.hook [headcount] push_ok = * commit_ok = * warnmsg = %(headcount)d new heads detected. You may not push new heads to this repository. debug = False All this is as per the install instructions. I then cloned the repository, created a branch, committed a change to that branch, and then issued: hg push -f as a test. However, this fails with: C:\junk\htmlwriter>hg push -f pushing to c:\code\htmlwriter searching for changes adding changesets adding manifests adding file changes added 1 changesets with 1 changes to 1 files transaction abort! rollback completed abort: pretxnchangegroup.headcount hook is invalid (import of "headcount.headcou nt" failed) I then ran this: C:\Python26>python c:\Python26\Lib\site-packages\headcount\headcount.py Traceback (most recent call last): File "c:\Python26\Lib\site-packages\headcount\headcount.py", line 2, in <modul e> import mercurial.node ImportError: No module named mercurial.node I'm far from a python expert, so can someone help me figure out how to get the headcount hook to run inside my mercurial environment? Details: Windows 7, Mercurial 1.7.2, TortoiseHg 1.1.7

  Read the article

< Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >