Search Results

Search found 11197 results on 448 pages for 'related'.

Page 393/448 | < Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >

• Radeon HD4850 serious issues when using DirectX 10

  - by ricsmania

  Hello, I have a problem with my video card. Whenever I run a DirectX 10 game, it works for a few seconds (10 or so) and then starts displaying nothing but big polygons. I have tested this with Crysis and Resident Evil 5, both have the same problems. The same games running under DirectX 9 work fine, except for some small black squares once in a while. I have the following specs: Asus P7P55D LE Intel Core i5 750 Sapphire Radeon HD4850 1GB 2x2GB Patriot Viper II Sector 5, DDR3 1600 MHz OCZ Stealth X Stream 500SXS 500W At first I thought it could be the video card overheating (it has stock cooling), but the game crashes even when it's running at 50 degrees C, and it's never been higher than 70. I also thought it could be the PSU, but as far as I know 500W is enough for this computer, especially because I haven't overclocked anything. My OS is Windows 7 X64 and I am using Catalyst 10.10, but I have also tried many older versions with no success. I don't think there is a problem with the card itself, or else it wouldn't run DirectX 9 games I believe. I have spent many hours searching for a solution but I couldn't, so any help is appreciated. Thank you. EDIT: I did some further investigation about the problem, and it seems taspeotis was right, it might be related to memory. I slightly underclocked the memory from 993 to 965 MHz and the problem went away completely. Both the black squares using DirectX 9 and the weird polygons using DirectX 10. I was using RE DirectX 10 Benchmark, as it consistently crashed around the same point, and now I can play the full benchmark with no artifacts at all. Unfortunately, the underclock has an obvious hit in performance. Although it's not critical, it's definitely noticeable. So, if the video memory test software showed no erros, but the card needs an underclock to work, what might be the problem? Temperature? Voltage? By the way, I couldn't find what the default voltage for this card is. And what is a good software to try and increase it? I tried Ati Tray Tools but it has a bug that increases the clock speed dramatically whenever I change something in the Overclock tab, so I'm afraid it might fry my card. Worst case scenario, if I don't find I solution I will try to slightly increase the GPU clock to compensate for the memory clock. Thank you again.

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Use windows 7 inside virtual box,as guest i mean, to create a Windows 7 USB using "Windows 7 USB/DVD Download Tool" ? (Linux as host)

  - by Abel Coto

  I want to download the Windows 7 professional iso (x32), from microsoft, and , i can do two things. Or buy a new burner , as mine doesn't work (i am trying to decide what dvd writer i could buy) or use a usb dongle to copy the iso to it , and install it via usb. I want to install Windows 7 in a netbook that now has debian,and in my pc. I think i have to buy only the license for the pc , as the netbook came with windows 7 preinstalled, so i suppose that i can use that serial to activate the windows , although i don't know how to install windows 7 starter instead of professional (i think if you remove a file from the iso, windows let you choose the edition to install). The problem is that in both pcs there isn't any windows , only debian. My father has a netbook with windows 7 starter, but i think it hasn't antivirus (at least until have the Karspersky Internet security for 3 pcs bought ), and i don't trust to make the usb there , if i don't now that there isn't any virus or malware. So i am trying to find a way of Create a Windows 7 usb installation , to at least be able to install windows 7 in the netbook without a external dvd writer. I know that with dd in linux you can copy a debian.iso to the usb , and then install debian with it (i've done it) using something like dd if=win7.iso of=/dev/sdb, but i don't know if this would work for windows 7 iso,and if dd will correctly copy the iso to the usb. I suppose that if you are able to boot and install windows 7 from the usb , is that the method works,and you can forget of problems later with the windows 7 installation (problems because some files could not be copied or like). So , i remembered that Microsoft created a tool to copy the iso to the usb using windows. So i thought that i could install in my pc , virtual box , as i have VT and 8 GB ram in it, and download the iso from microsoft ,install windows 7 in the virtual machine , and then copy the iso inside the machine , donwload the iso tool, and atach a usb to the pc, connect it to the guest , and use the tool to copy the iso to the USB. But i don't now if is possible to use a virtual machine to do this , or the virtualization could give problems with the usb, or something. I have found some minutes ago this How to make a windows 7 usb flash install media, from linux? The first method (dd) is the one i like more , and i trust more ( i don't now if the second method using ms-sys , works well , and if i can trust it. I understand that a iso is like a .rar , but no compressed,only containing the files ,so mount the iso and cp the data inside perhaps is ok. Although the method i like more is the microsoft one (more because is from microsoft , and i suppose they now what they do ,at least with this usb related thing, than anything). Perhaps worth more to buy a external dvd writer haha ... Should the virtual machine method work ?

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

  - by Martin

  Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

  Read the article

• What issues ensue from having multiple versions of Office installed?

  - by Michael Sorens

  My ultimate question is embodied in the title but I thought it might be helpful to others if I detail what instigated my inquiry and my examination of the problem. To me, the first rule of software updates is Primum non nocere -- first, do no harm. So with my Windows 7 system containing both Office 2003 and Office 2010 I blithely proceeded to install this month's updates from Microsoft, containing updates for both versions of Office. While Microsoft officially does not recommend running multiple versions (see, for example, Running Multiple Versions of Microsoft Excel it is possible; I have had two versions installed for a year or more and have never run into an issue before. One thing that is always mentioned is installation order, i.e., the one you want to open files by default should be installed last. I wanted 2010 as my default so I had indeed installed 2003 first then, years later, 2010. So with this round of Windows updates, either it installed patches to 2010 before 2003, knocking out the file association, or the 2003 patch was more comprehensive, in the sense of touching the file association while the 2010 did not. In any case, after updates, double-clicking a .xls file opened 2003 rather than 2010. Web search indicated either: Use the file associations control panel to re-associate .xls files with the correct version of excel. I looked at this first, but it showed what seemed to be an unversioned "Excel" associated with .xls files so I did not check further. (This turned out to be an error on my part; more later.) Re-install versions in the desired order; I find this unreasonable. Run the repair option of the Office installer on the desired version; still seems more work than one should need. Run excel from the command line with "/regserver" on the one to be the default and "/unregserver" on the other. Good idea, but further search indicated that neither 2007 nor 2010 support "/regserver" contrary to some posts (e.g. Default Program With Multiple Versions Installed). Since this was a Windows Update issue and Microsoft provides free support for such, I inquired there as well, but succeeded only in getting the suggestion to uninstall all other versions, period; not acceptable to me. What worked for me was going back to the file associations control panel and manually selected the Office 2010 version of Excel. While it appeared no different in the control panel, it did fix the double-click issue. So if all it takes is this simple fix after an update, I can live with that. What I am wondering is: Has anyone seen any other problems related to having multiple versions of Office installed?

  Read the article

• Automating silent software deployments on Solaris 10

  - by datSilencer

  Hello everyone. Essentially, the question I'd like to ask is related to the automation of software package deployments on Solaris 10. Specifically, I have a set of software components in tar files that run as daemon processes after being extracted and configured in the host environment. Pretty much like any server side software package out there, I need to ensure that a list of prerequisites are met before extracting and running the software. For example: Checking that certain users exists, and they are associated with one or many user groups. If not, then create them and their group associations. Checking that target application folders exist and if not, then create them with preconfigured path values defined when the package was assembled. Checking that such folders have the appropriate access control level and ownership for a certain user. If not, then set them. Checking that a set of environment variables are defined in /etc/profile, pointed to predefined path locations, added to the general $PATH environment variable, and finally exported into the user's environment. Other files include /etc/services and /etc/system. Obviously, doing this for many boxes (the goal in question) by hand can be slow and error prone. I believe a better alternative is to somehow automate this process. So far I have thought about the following options, and discarded them for one reason or another. 1) Traditional shell scripts. I've only troubleshooted these before, and I don't really have much experience with them. These would be my last resort. 2) Python scripts using the pexpect library for analyzing system command output. This was my initial choice since the target Solaris environments have it installed. However, I want to make sure that I'm not reinveting the wheel again :P. 3) Ant or Gradle scripts. They may be an option since the boxes also have java 1.5 enabled, and the fileset abstractions can be very useful. However, they may fall short when dealing with user and folder permissions checking/setting. It seems obvious to me that I'm not the first person in this situation, but I don't seem to find a utility framework geared towards this purpose. Please let me know if there's a better way to accomplish this. I thank you for your time and help.

  Read the article

• Rebasing a branch which is public

  - by Dror

  I'm failing to understand how to use git-rebase, and I consider the following example. Let's start a repository in ~/tmp/repo: $ git init Then add a file foo $ echo "hello world" > foo which is then added and committed: $ git add foo $ git commit -m "Added foo" Next, I started a remote repository. In ~/tmp/bare.git I ran $ git init --bare In order to link repo to bare.git I ran $ git remote add origin ../bare.git/ $ git push --set-upstream origin master Next, lets branch, add a file and set an upstream for the new branch b1: $ git checkout -b b1 $ echo "bar" > foo2 $ git add foo2 $ git commit -m "add foo2 in b1" $ git push --set-upstream origin b1 Now it is time to switch back to master and change something there: $ echo "change foo" > foo $ git commit -a -m "changed foo in master" $ git push At this point in master the file foo contain changed foo, while in b1 it is still hello world. Finally, I want to sync b1 with the progress made in master. $ git checkout b1 $ git fetch origin $ git rebase origin/master At this point git st returns: # On branch b1 # Your branch and 'origin/b1' have diverged, # and have 2 and 1 different commit each, respectively. # (use "git pull" to merge the remote branch into yours) # nothing to commit, working directory clean At this point the content of foo in the branch b1 is change foo as well. So what does this warning mean? I expected I should do a git push, git suggests to do git pull... According to this answer, this is more or less it, and in his comment @FrerichRaabe explicitly say that I don't need to do a pull. What's going on here? What is the danger, how should one proceed? How should the history be kept consistent? What is the interplay between the case described above and the following citation: Do not rebase commits that you have pushed to a public repository. taken from pro git book. I guess it is somehow related, and if not I would love to know why. What's the relation between the above scenario and the procedure I described in this post.

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

  - by Janar

  I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

  Read the article

• Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

  Read the article

• SSH: Port Forwarding, Firewalls, & Plesk

  - by Kian Mayne

  I edited my SSH configuration to accept connections on Port 213, as it was one of the few ports that my work firewall allows through. I then restarted sshd and everything was going well. I tested the ssh server locally, and checked the sshd service was listening on port 213; however, I still cannot get it to work outside of localhost. PuTTY gives a connection refused message, and some of the sites that allow check of ports I tried said the port was closed. To me, this is either firewall or port forwarding. But I've already added inbound and outbound exceptions for it. Is this a problem with my server host, or is there something I've missed? My full SSH config file, as requested: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 Port 213 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Got Hacked. Want to understand how.

  - by gaoshan88

  Someone has, for the second time, appended a chunk of javascript to a site I help run. This javascript hijacks Google adsense, inserting their own account number, and sticking ads all over. The code is always appended, always in one specific directory (one used by a third party ad program), affects a number of files in a number of directories inside this one ad dir (20 or so) and is inserted at roughly the same overnight time. The adsense account belongs to a Chinese website (located in a town not an hour from where I will be in China next month. Maybe I should go bust heads... kidding, sort of), btw... here is the info on the site: http://serversiders.com/fhr.com.cn So, how could they append text to these files? Is it related to the permissions set on the files (ranging from 755 to 644)? To the webserver user (it's on MediaTemple so it should be secure, yes?)? I mean, if you have a file that has permissions set to 777 I still can't just add code to it at will... how might they be doing this? Here is a sample of the actual code for your viewing pleasure (and as you can see... not much to it. The real trick is how they got it in there): <script type="text/javascript"><!-- google_ad_client = "pub-5465156513898836"; /* 728x90_as */ google_ad_slot = "4840387765"; google_ad_width = 728; google_ad_height = 90; //--> </script> <script type="text/javascript" src="http://pagead2.googlesyndication.com/pagead/show_ads.js"> </script> Since a number of folks have mentioned it, here is what I have checked (and by checked I mean I looked around the time the files were modified for any weirdness and I grepped the files for POST statements and directory traversals: access_log (nothing around the time except normal (i.e. excessive) msn bot traffic) error_log (nothing but the usual file does not exist errors for innocuous looking files) ssl_log (nothing but the usual) messages_log (no FTP access in here except for me)

  Read the article

• When upgrading from Vista to Windows 7 on a DELL laptop, how do I know which drivers to reinstall an

  - by msorens

  According to Dell's upgrade page for Vista to Windows 7, after using the upgrade assistant the final step is to install drivers. They refer to this page for the order of driver installation, listing 9 items. From there I go to the Dell Drivers and Downloads page, enter my system tag, and get a list of the downloads available for my specific box. That page, by the way, has a link to driver install instructions that lists 10 rather than 9 items. Going to Drivers Help in the side panel and clicking on "In what order should drivers be installed?" shows yet a third list, this one containing 13 items. Not surprisingly, the order of these 3 lists of drivers are not quite the same for the common items! Furthermore, of the 26 files Dell's site recommends for my machine, there are several not shown on any of the 3 lists! I can make determinations for some of these: 6 of them are "applications" so I know which of those I want and that they could probably be safely installed after all drivers. BIOS: I would think this should be unaffected by an OS upgrade so could be skipped. Two tools in the diagnostics category: could probably be done after all drivers. That leaves just a CD/DVD driver and a webcam driver unaccounted for. So my two related questions are these: How critical is the driver installation order and which one do I follow? (Keep in mind this is for an upgrade, not a fresh install.) Where in the order do I insert the CD/DVD and the webcam drivers (if needed) ? Dell's driver download page provides (in theory) the list of all downloads relevant to my specific machine, via the service tag. But do I actually need to reinstall all of them? some? none? How does one determine this? They do label each with Recommended or Optional, so do I need to reinstall all the recommended ones? (Part of the reason for my perplexed frown is that I wonder why I would need to reinstall a CD/DVD driver since I would already be using the drive to install the OS!)

  Read the article

• Synchronize the same set of files to 2 different locations with 2 different programs for 2 different purposes

  - by Hedgetrimmer

  Because of stupid questionable IT policies at my not-to-be-named place of occupation, I have been (and will be, for the forseeable future) carrying on an external hard drive a unison-synchronized copy of all of my documents and code, including code which resides in some of my "dotfiles" and other code which resides in ~/bin (things I've made are there because ~/bin is in my $PATH) along with some cruft generated (and to be generated) by conscript and its related "giter8" templating system for Scala project boilerplates. Despite this, I do use a symlinking program to store all of my important dotfiles in a subdirectory. Thanks to that somewhat complicated setup, I have resorted to making a directory full of symlinks to every directory (or file, as is the case with stuff under ~/bin) that I want synchronized, and then follow = True is in my unison profile. It happens to be that this collection of odds and ends—plus an automatically-generated text file containing every package installed on my system—is everything under ~ that needs to be backed up to a remote (rsync-over-ssh) host with client-side encryption and signing from GPG. I already believe that duplicity is the most appropriate program to do that. What isn't as clear-cut is how to make duplicity use the exact same set of files when it runs a backup; it would be simple if duplicity would follow symlinks, but it does not and the manpage lists no option for enabling any such behavior. Comparing unison's file selection algorithm to duplicity's, I don't think I can write a program that could compute a ruleset for one program given one for the other. For the record, I would rather not keep the symlinks manually synchronized with duplicity file-selection rules, as they can change thanks to the above-mentioned complications regarding ~/bin. I don't think running duplicity on the external hard disk is such a good idea either; I usually keep that hard disk unmounted and unplugged in case of a power failure or other physical problem with the computer, plus I'm not sure about duplicity's performance given that: the hard disk is NTFS-formatted in order to be useable at my Windows-imprisoned place of occupation. despite being a USB 3.0 disk, my computer has no USB 3.0 ports so it acts as a USB 2.0 disk. How can I have duplicity (or is there a better program that I have overlooked?) back up the exact same set of files that is bidirectionally synchronized with my external hard disk?

  Read the article

• Alternative Windows Offline Files + Windows Backup + Previous Version Setup

  - by Herson

  Currently our documents are all hosted in a Windows 7 box. Users can access the files using Windows share and the documents are available offline (windows 7 feature). The documents are being backed up daily by Windows 7 backup and restore utility. Users can access previous versions of the file (from the backups) using Windows Explorer "previous versions" feature. This setup is currently working well, except for the following: We would prefer to have access to hourly versions of the file, not daily. The previous version mechanism is tied up to the backup mechanism. Windows 7 performs a full backup every week and incremental backup everyday. The previous versions of a file is actually what are the available in the backups. If you 20GB documents and want to maintain at least three(3) year history, you will use at minimum 3 years * 52 weeks * 20GB or about 3TB even if there are few changes in the documents. Its pretty inefficient use of space. Looking up previous versions of a file is very slow (tens of minutes). This is probably related to the previous issue - Windows has to traverse its all of its backups. I am considering using SVN + autocommit/autoupdate tortoisesvn. It will have the following advantages: Backups are easy and will also backup the whole history of each documents. (Just backup the repository). Creating previous versions can be frequent. I think svn commit / update can be done every two minutes or so. Users can sync over the net. However, I can see the following issues: More conflicts than the original setup because both multiple users can now edit the same file even both are online, i.e. can connect to the SVN repo. The users can off course lock the file first before editing, but that would mean they have to adjust. Delay on propagation of file changes. On windows 7 file sharing, changes made by one online user will be instantaneously available to other online users. With the SVN setup, changes will only be propagated when the users execute the svn add/commit/update sequence. Delay will be probably a few minutes. This workflow will no longer work: "Hi, I just edited document X, can you have a quick look?" I would like to ask the opinion of the community for alternative setups, or improvements on the above setups to work out the kinks.

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• Gentoo box can't cURL or ping after restarting net.eth1

  - by Curlybraces

  Hi all, the following is completely baffling me. We currently have a gentoo box which acts as our LAMP, DNS, DHCP server. This is assigned a static IP on the network. This server is connected directly to the internet via a BT BusinessHub Router. The server is also connected to a patch panel/switch port which connects the remaining office (around 10 PC's) to the server. Everything has been plain sailing until the other day when the server was restarted. For some reason now only portions of network accessibility is available depending on which ethernet device was last restarted. Restarting net.eth0 allows the office server to cURL, ping, etc but stops all networked PC's from accessing the internet. Then restarting net.eth1 restores all internet to the network but stops the server from curling, pinging, etc again. However, even when the server can't ping, curl, etc, I can still remote SSH and remote MySQL connect from the server command line to other external servers that we own. Here's my route map (router is 192.168.1.254): Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 eth1 Here's my /etc/conf.d/net: iface_eth0="192.168.1.99 broadcast 192.168.1.255 netmask 255.255.255.0" iface_eth1="dhcp" None of the above have ever been changed however. Things have just ceased to operate correctly, which makes me think it's a freshly added Iptables rule. Here's the Iptables Filter table: Chain INPUT (policy ACCEPT) target prot opt source destination DROP tcp -- ##.##.##.## anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere tcp dpt:2199 ACCEPT tcp -- anywhere anywhere tcp dpt:3199 ACCEPT tcp -- ##.###.###.## anywhere tcp dpt:http ACCEPT tcp -- ###.###.##.## anywhere tcp dpt:2199 ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:http ACCEPT tcp -- ##.###.##.## anywhere tcp dpt:http ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:3128 ACCEPT udp -- ##.###.###.### anywhere udp dpt:3128 ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:http ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:https Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere ##.###.###.## DROP all -- anywhere ##.###.###.## ACCEPT all -- anywhere anywhere state NEW,ESTABLISHED Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp spt:2199 ACCEPT udp -- anywhere anywhere udp spt:4817 ACCEPT udp -- anywhere anywhere udp spt:4819 ACCEPT udp -- anywhere anywhere udp spt:3199 Help gratefully appreciated.

  Read the article

• Both nginx and php5-fpm init.d startup scripts are non-functional and returning no errors..? But they used to work perfectly

  - by Ollie Treend

  I have been using nginx and php5-fpm on my Ubuntu box for a while now. Everything has been configured and setup correctly, and it ran like a charm. I have been keeping the packages updated & upgraded as usual, but haven't touched the nginx OR php5-fpm config files at all (thus I'm pretty sure this isn't my fault... ) Basically, I noticed nginx wasn't running as it should be. I ran the command sudo service nginx start, and the script did nothing. The same thing happens when trying to do anything - start, stop, restart or reload. This also happens for the "php5-fpm" init script - although all other init scripts seem to be functioning correctly. When trying to start nginx OR php5-fpm, this is what happens: root@HAL:/etc# service php5-fpm start root@HAL:/etc# I can't understand what is going wrong. The script isn't returning errors, but similarly it isn't starting the daemon or reporting success as usual. For reference, both installations are from the official nginx and php5-fpm PPAs. The fact that both started doing this at the same time has thrown me - since they are both unrelated packages. I have since purged both sets of packages from my system with apt-get purge ... and also apt-get remove --purge ... both of which have successfully removed the packages, their config files, and their init.d startup scripts. After having reinstalled nginx, I now have a functioning startup script again - I can start the web server as usual. However, php5-fpm is still experiencing the strange premature exiting of the startup script.. and I really can't figure out what's causing it. I have no idea what caused this to occur initially, but have managed to fix nginx. I now need to fix the php5-fpm startup script. If anybody could shed some light on this situation, I would be very grateful! The chances are both these issues are related - and they were caused by me doing something stupid. But now I need to fix it. This time I was lucky - because these problems are just on my development server. But I have 2 other live servers which are configured in a similar way, and I am worried the same thing will happen to these two as well! Has anybody else come across this? Do you have any words of advice? Thank you

  Read the article

• High CPU usage - symptoms moving from server to server after bouncing

  - by grt3kl

  First off, I apologize if I didn't include enough information to properly troubleshoot this issue. This sort of thing isn't my specialty, so it is a learning process. If there's something I need to provide, please let me know and I'll be happy to do what I can. The images associated with my question are at the bottom of this post. We are dealing with a clustered environment of four WebLogic 9.2 Java application servers. The cluster utilizes a round-robin load algorithm. Other details include: Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_12-b04) BEA JRockit(R) (build R27.4.0-90_CR352234-91983-1.5.0_12-20071115-1605-linux-x86_64, compiled mode) Basically, I started looking at the servers' performance because our customers are seeing lots of lag at various times of the day. Our servers should easily handle the loads they are given, so it's not clear what's going on. Using HP Performance Manager, I generated some graphs that indicate that the CPU usage is completely out of whack. It seems that, at any given point, one or more of the servers has a CPU utilization of over 50%. I know this isn't particularly high, but I would say it is a red flag based on the CPU utilization of the other servers in the WebLogic cluster. Interesting things to note: The high CPU utilization was occurring only on server02 for several weeks. The server crashed (extremely rare; we are not sure if it's related to this) and upon starting it back up, the CPU utilization was normal on all 4 servers. We restarted all 4 managed servers and the application server (on server01) yesterday, on 2/28. As you can see, server03 and server04 picked up the behavior that was seen on server02 before. The CPU utilization is a Java process owned by the application user (appown). The number of transactions is consistent across all servers. It doesn't seem like any one server is actually handling more than another. If anyone has any ideas or can at least point me in the right direction, that would be great. Again, please let me know if there is any additional information I should post. Thanks!

  Read the article

• Too many Tunnel Adapter Interfaces

  - by Tomas Lycken

  If I open a command prompt on my machine and type ipconfig /all, I see lots of Tunnel adapter Local Area Connection* 9: Media state . . . . . . . . . . . . . : Media disconnected Connection-specific DNS Sufficx . . . : Description . . . . . . . . . . . . . : Microsoft 6to4 Adapter #5 Physical address. . . . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . . . : No Autoconfiguration Enabled . . . . . . : Yes In fact, they're so many that my "real" adapters are pushed out of the stack, and can't be seen anymore. Is there any flag I can use on ipconfig to hide all virtual interfaces? Or is there some other way around this problem? Since they always say "Media disconnected" I suppose disabling could be an option, but if possible I'd rather not turn any functionality off. I just want to control what output I get from ipconfig. Also, I know these are related to IPv6 stuff. However, most of what I find on google merely states what these are, and that they're harmless - nothing about hiding/removing them.

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

< Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >