Search Results

Search found 12645 results on 506 pages for 'maintenance mode'.

Page 394/506 | < Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >

• Delay NTP Initialisation, Cisco 877W, IOS 12.4(24)T1

  - by Mike Insch

  I have a Cisco 877W which I'm using for my home ADSL connection (and as a refresher in Cisco IOS). I've got a working config in-place with my PPPoA connection coming online correctly, and VLANs and other settings configured as I want them, but I can't crack the NTP configuration. For NTP, I have the following defined ntp server 0.uk.pool.ntp.org source Dialer0 ntp server 1.uk.pool.ntp.org source Dialer0 ntp server 2.uk.pool.ntp.org source Dialer0 ntp server 3.uk.pool.ntp.org source Dialer0 This setup works fine when issued in Global Configuration Mode when the Dialer0 interface (ATM0.1) is up. The configuration fails at startup though: Translating "1.uk.pool.ntp.org"...domain server (208.67.222.222) (208.67.220.220) ntp server 1.uk.pool.ntp.org source Dialer0 ^ % Invalid input detected at "^" marker. This is repeated for the other servers defined. Obviously the DNS lookup for the server(s) fails because the DNS servers cannot be accessed because the external interface is not yet online. Is there a way to delay the NTP configuration until afte the Dialer0 interface is fully initialised? Can the NTP commands be triggered by the Line Protocol on the Dialer0 interface transitioning to the up state? Alternatively, can the NTP commands be delayed for 5 minutes after the router has finished initialising? Any advice, or pointers to useful documentation or examples gratefully received ...

  Read the article

• Why can't I connect to computers on my network using our external IP address?

  - by Kivin

  My home network is serviced by an ADSL line. The modem is in bridged mode. The router performs the PPPoE. Three computers are connected to the router: two wired Windows 7 boxes and a Ubuntu Linux box over wifi. The computers are hosting various forms of services including FTP and HTTP. The router has port forwarding mapped from the relevant ports to the reserved IP addresses for the computers. If I attempt to connect to a server inside the network, such as ftp://67.xx.xxx.xxx from inside the network, the request times out. However if I connect using the internally mapped address, such as ftp://192.168.0.100, all is well. This is a nuisance for setting up software, especially on the laptop which needs to be able to phone home from anywhere, and I just don't have enough expertise with networking to know why this is occurring to even have a clue whether it can be solved or not. edit: It should be noted that the servers can be accessible outside the network - say, at the starbucks across the street - perfectly fine, using the ISP provided address and the appropriate port.

  Read the article

• How can I set Vim to obey accents of my spoken language?

  - by naxa

  When pressing w or e in sentences with accents (written in my native language), such as the first one (marked **) here: **Éj-mélybol fölzengo** - csing-ling-ling - száncsengo. Száncsengo - csing-ling-ling - tél csendjén halkan ring. [1] the characters o, ö, among others [2], make my gVim think they are word-ends so it stops on them (in Normal mode). gVim stops on the positions marked with _ where it shouldn't: Éj-mélyb_ol f_ölzeng_o. I would like to set gVim so it properly handle words even when containing accents and other local characters. But where do I set this? I use it on Win32, vim v 7.3.46. [1] - excerpt of a poem by Weöres Sándor [2] - "others", not mentioned here :) like í, u are also a problem. On the other hand, gVim seems to already work with é and á. gVim version info: VIM - Vi IMproved 7.3 (2010 Aug 15, compiled Oct 27 2010 17:59:02) Included patches: 1-46 Compiled by Bram@KIBAALE Big version with GUI. Features included (+) or not (-): +arabic +autocmd +balloon_eval +browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con_gui +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse +mouseshape +multi_byte_ime/dyn +multi_lang -mzscheme +netbeans_intg +ole -osfiletype +path_extra +perl/dyn +persistent_undo -postscript +printer -profile +python/dyn +python3/dyn +quickfix +reltime +rightleft +ruby/dyn +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white +tcl/dyn -tgetent -termresponse +textobjects +title +toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save +xpm_w32

  Read the article

• Poor Write Performance in VM inside Proxmox PVE 2.0

  - by sorsenne

  I am running a PVE 2.0 on a decent Hardware (2 SATA HDDs as RAID1, 12GB RAM, i7 CPU) but the I/O Performance is very poor inside the VM (Ubuntu 11.10 Server). The very same VM was copied to another Server running simply Ubuntu Server with KVM and had better I/O Perf. this is how the HDD is shown in the Guest: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: ST3000DM001-9YN166, CC49, max UDMA/133 ata1.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC49 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I tested with DD: $ dd bs=1M count=128 if=/dev/zero of=test conv=fdatasync 128+0 records in 128+0 records out 134217728 bytes (134 MB) copied, 19.2222 s, 7.0 MB/s on the Host, this same Test will result with 156 MB/s in average. PS: I am using VirtIO and see no error in dmesg.

  Read the article

• How can I disable the CTRL-ALT-DEL key combination completely on XP/Vista/7?

  - by Travesty3

  I have been googling extensively to figure this out, and nobody seems to be able to give a direct answer. Let me start by saying that I'm NOT talking about requiring CTRL-ALT-DEL to enter logon information. I'm working on a golf simulator program which is used at golf centers. I need the ability to completely disable the CTRL-ALT-DEL key sequence so that the golf center customers can't get out of the program and access the computer at all. I realize there are other key combinations that need to be handled as well, we already have this entire feature working in XP, but we're going to be switching to Windows 7 soon, and CTRL-ALT-DEL is the only one that doesn't seem to work in Win7. I'd really like an all-around solution if at all possible. This same program may also be installed on a client's personal computer for an in-home golf simulator, but the computers that really need this feature (golf center computers) are provided to the golf center by us, so would the best option be to write a new shell? I don't know anything about that at all, other than others that suggest writing a new shell for kiosk mode. I'd really like a simpler option, like modifying the registry in some way. I have heard that you can remove some buttons from the menu screen that pops up, but unless I can remove pretty much all of them (including the shutdown/restart button in the bottom-right corner), this won't be enough of a solution for me. Thanks for taking the time to read this and thanks again for any help you could provide! -Travis

  Read the article

• vagrant and puppet security for ssl certificates

  - by Sirex

  I'm pretty new to vagrant, would someone who knows more about it (and puppet) be able to explain how vagrant deals with the ssl certs needed when making vagrant testing machines that are processing the same node definition as the real production machines ? I run puppet in master / client mode, and I wish to spin up a vagrant version of my puppet production nodes, primarily to test new puppet code against. If my production machine is, say, sql.domain.com I spin up a vagrant machine of, say, sql.vagrant.domain.com. In the vagrant file I then use the puppet_server provisioner, and give a puppet.puppet_node entry of “sql.domain.com” to it gets the same puppet node definition. On the puppet server I use a regex of something like /*.sql.domain.com/ on that node entry so that both the vagrant machine and the real one get that node entry on the puppet server. Finally, I enable auto-signing for *.vagrant.domain.com in puppet's autosign.conf, so the vagrant machine gets signed. So far, so good... However: If one machine on my network gets rooted, say, unimportant.domain.com, what's to stop the attacker changing the hostname on that machine to sql.vagrant.domain.com, deleting the old puppet ssl cert off of it and then re-run puppet with a given node name of sql.domain.com ? The new ssl cert would be autosigned by puppet, match the node name regex, and then this hacked node would get all the juicy information intended for the sql machine ?! One solution I can think of is to avoid autosigning, and put the known puppet ssl cert for the real production machine into the vagrant shared directory, and then have a vagrant ssh job move it into place. The downside of this is I end up with all my ssl certs for each production machine sitting in one git repo (my vagrant repo) and thereby on each developer's machine – which may or may not be an issue, but it dosen't sound like the right way of doing this. tl;dr: How do other people deal with vagrant & puppet ssl certificates for development or testing clones of production machines ?

  Read the article

• Windows XP, Preference menu's hidden for many programs

  - by Jestep

  I don't know when this started happening, but it has been several months since I first noticed it. Basically, when I go to a preferences menu of some programs, the preferences window is completely hidden, but the program see's it as being open. This prevents me from interacting with the preferences and the actual program. So far I've noticed it on Adobe Illustrator and Netbeans. Illustrator when I select edit - Preferences - An Option. On Netbeans it happens when I right click on a site and select properties. Here's a link to a screen shot after I click on the preferences menu (I don't have enough points to post an image yet): http://www.jestep.com/images/screen-2.jpg. Note that the main workspace is grayed out. I have to hit Escape to close the hidden preferences window. I've tried unstinstalling, completely wiping the registry of any trace of the program and reinstalling. Thought it may have been a multi-monitor issue when I switched from 2 monitors down to 1, but menu's were not on other monitor when I plugged one back in. I've reset workspaces, windows display, windows performance settings, changed resolution, safe mode, everything I can think of. I cannot figure out what would cause the same problem on completely unrelated software, and I cannot reset it by reinstalling. Any help would be greatly appreciated.

  Read the article

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• DNS Resolution doesn't work after uninstalling Cisco VPN & Deterministic Network Enhancer in Win 7

  - by Craig M

  I just upgraded my home PC to Windows 7 Ultimate 32 bit. After trying various methods to get the Cisco VPN client to work, I gave up and decided to just run it in XP mode. The last steps I tried were in this article ( http://social.technet.microsoft.com/Forums/en-US/w7itproappcompat/thread/d880dfe5-7f44-4955-8620-2a9355d8ea8b/ ) After that, I uninstalled the Cisco client and rebooted. I uninstalled the Deterministic Network Enhancer and rebooted again. Both uninstalled successfully, but now I'm not able to resolve any DNS. The only way I can resolve DNS is to reinstall the DNE, reboot, and uninstall the DNE. Then I am able to resolve DNS lookups until I reboot again. Once it's rebooted, no more DNS. Any ideas? Edit: I completely forgot I'd asked this question until harrymc posted his answer. I've since found out that to fix this problem, I need to disable my Local Area Connection and re-enable it. Once I do that I have no trouble making network connections until the next time I reboot at which point I repeat the process. It's annoying, but manageable since I reboot very infrequently.

  Read the article

• Strange ASP.NET Queue Performance Counters Behavior?

  - by LemurTech

  We have an ASP.NET 2.0 site running in classic mode. I am seeing very strange behavior in the performance counter values. Perhaps these are bugs (I've been all over Google trying to verify this, without much luck), or perhaps it is just my inexperience with monitoring these things. This PerfMon graph (http://imgur.com/Jv5io5J) represents a load test where I add up to 350 virtual users to the site, at a rate of about 1/sec, performing relatively simple page browsing. At the end of the test, I gradually taper off the number of users. This is a 4 CPU server. Machine.config settings for are at the defaults. The solid blue line is ASP.NET Apps v2.x\Requests Executing for the application in question. The profile makes perfect sense, with a quick ramp-up to 32 executing requests (minWorkerThreads x 4CPUs), followed by a slower ramp-up to 48 ((maxWorkerThreads - minWorkerThreads) x 4CPUs). The solid yellow line is ASP.NET v2.x\Requests Queued. Again, this makes sense: after the initial 32 request threads are activated, the queue begins to build as new thread initialization can't keep pace with incoming requests. But as executing requests reaches its highest possible value of 48, the counter for ASP.NET Apps v2.x\Requests Queued (green solid line) suddenly springs to life and maintains step with the yellow counter. As far as I can tell, and with no other apps running on the server, these two counters should have had the same values from the start. One other odd thing: The counter for ASP.NET v2.x\Request Wait Time (dotted yellow line) also does not spring to life until executing requests reaches 48. Shouldn't I be seeing values here from the moment ASP.NET v2.x\Requests Queued begins to build? And likewise, why would ASP.NET Apps v2.x\Request Execution Time (dotted blue) increase significantly only after that peak of 48 is reached? Shouldn't it ramp-up gradually along with queued requests?

  Read the article

• OpenVPN: ERROR: could not read Auth username from stdin

  - by user56231

  I managed to setup openvpn but now I want to integrate a user/pass authentication method so, even though I haven't added the auth-nocache in the server config, whenever I try to connect it returns with the following message on the client side: ERROR: could not read Auth username from stdin My server.conf file contains basic stuff, everything works up untill I try to implement this for of authentication. mode server dev tun proto tcp port 1194 keepalive 10 120 plugin /usr/lib/openvpn/openvpn-auth-pam.so login client-cert-not-required username-as-common-name auth-user-pass-verify /etc/openvpn/auth.pl via-env ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem user nobody group nogroup server 10.8.0.0 255.255.255.0 persist-key persist-tun #persist-local-ip status openvpn-status.log verb 3 client-to-client push "redirect-gateway def1" push "dhcp-option DNS 10.8.0.1" log-append /var/log/openvpn comp-lzo I searched all over the net for a solution and all answers seems to be related to the auth-nocache param which I haven't set. The directive auth-user-pass-verify /etc/openvpn/auth.pl via-env points to a script which is executed to perform the authentication. A false authentication should result in a exit 1 while a true one should result with exit 0. For testing, that script auth.pl returns exit 0 no matter what the input is but it seems that the file is not executed before the error raises. auth.pl file contents: #!/usr/bin/perl my $user = $ENV{username}; my $passwd = $ENV{password}; printf("$user : $passwd\n"); exit 0; Any ideas?

  Read the article

• Using AddEncoding x-gzip .gz without actual files

  - by STATUS_ACCESS_DENIED

  With Apache (2.2 and later) how can I achieve the following. I want to transparently compress using GZip encoding (not plain Deflate) the output when a certain file is queried with its name plus the extension .gz, where the .gz version doesn't physically exist on disk. So let's say I have a file named /path/foo.bar and no file foo.bar.gz in the folder to which the URI /path maps, how can I get Apache to serve the contents of /path/foo.bar but with AddEncoding x-gzip ... applied to the (non-existing) file? The rewrite part appears to be easy, but the problem is how to apply the encoding to a non-existent item. The other way around also seems to be simple as long as the client supports the encoding. Is the only solution really a script that does this on the fly? I'm aware of mod_deflate and mod_gzip and it is not what I'm looking for - at least not alone. In particular I need an actual GZIP file and not just a deflated stream. Now I was thinking of using mod_ext_filter, but couldn't bridge the gap between rewriting the name of the (non-existent) file.gz to file on one side and the LocationMatch on the other. Here's what I have. RewriteRule ^(.*?\.ext)\.gz$ $1 [L] ExtFilterDefine gzip mode=output cmd="/bin/gzip" <LocationMatch "/my-files/special-path/.*?\.ext\.gz"> AddType application/octet-stream .ext.gz SetOutputFilter gzip Header set Content-Encoding gzip </LocationMatch> Note that the header for Content-Encoding isn't really needed by the clients in this case. They expect to see actual GZIP files, but I want to do this on-the-fly without caching (this is a test scenario).

  Read the article

• [Ubuntu 10.04] mdadm - Can't get RAID5 Array To Start

  - by Matthew Hodgkins

  Hello, after a power failure my RAID array refuses to start. When I boot I have to sudo mdadm --assemble --force /dev/md0 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 to get mdadm to notice the array. Here are the details (after I force assemble). sudo mdadm --misc --detail /dev/md0: /dev/md0: Version : 00.90 Creation Time : Sun Apr 25 01:39:25 2010 Raid Level : raid5 Used Dev Size : 1465135872 (1397.26 GiB 1500.30 GB) Raid Devices : 6 Total Devices : 6 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 17 23:02:38 2010 State : active, Not Started Active Devices : 6 Working Devices : 6 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 128K UUID : 44a8f730:b9bea6ea:3a28392c:12b22235 (local to host hodge-fs) Events : 0.1249691 Number Major Minor RaidDevice State 0 8 65 0 active sync /dev/sde1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 49 3 active sync /dev/sdd1 4 8 33 4 active sync /dev/sdc1 5 8 17 5 active sync /dev/sdb1 mdadm.conf: # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions /dev/sdb1 /dev/sdb1 # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # definitions of existing MD arrays ARRAY /dev/md0 level=raid5 num-devices=6 UUID=44a8f730:b9bea6ea:3a28392c:12b22235 Any help would be appreciated.

  Read the article

• Cleaning a proxy/phishing trojan from Windows XP computer

  - by i-g

  I am trying to remove an interesting trojan from a Windows XP computer. It manifests itself as a phishing page (screenshot linked) that appears after the user tries to log on to eBay. So far, I haven't found any other web sites that are affected. As you can see, the trojan intercepts browser connections (all installed browsers are affected) and injects this phishing page. The address looks like it's ebay.com, but HTTPS verification doesn't work (no lock icon or green bar in Firefox.) At some point, Trojan.Dropper appeared on the computer. I removed it with Malwarebytes Anti-Malware. Although it reappeared several times, it seemed to be gone after I booted into Safe Mode and did a full system scan with MBAM. Now, however, a different trojan has appeared on the machine; I suspect it was installed by Trojan.Dropper. So far, MBAM, Ad-Aware, and Spybot S&D have been unable to remove it. I've looked for it in the HijackThis log but haven't found anything conclusive. Has anyone run across a trojan like this before? Where would I start looking for it to remove it manually? Thank you for reading.

  Read the article

• "The directory name is invalid" when trying to install drivers in Windows 7 via Device Manager

  - by Luke

  First off, this computer is not mine, it's a customer's system. Having said that... The hard drive was moved to a new motherboard, CPU, RAM combo, and booted up fine. Customer puts in driver CD, drivers won't load. He brings it into me. Under Device Manager for Windows 7 x64, I see lots of PCI to PCI bridge, one SMBus Controller, and about 20 Unknown Devices. Greeeeeat... So I start with the SMBus driver directly from the Asus website for the motherboard (P8H77-M Pro). If I install from the setup program, it tells me to reboot, then it starts the install. It gets half way through the setup, then fails (An unknown error occurred. Setup will exit). When I try to point to the folder from Device Manager, it starts copying files for the driver, even presents me with the proper name of the device, but says that an error has occurred there as well: The directory name is invalid. Doing some Googling, I saw that many people had this issue with Vista. K, Vista and 7 are similar, maybe the solutions are the same... But they aren't. I tried: Copying the entire driver folder and setup utility to the Program Files folder and running it / selecting it in DM Downloading another set of drivers in case this one is corrupt Disabling UAC Deleting and recreating the %WINDIR%\TEMP folder Removing all references to previous hardware that I could find, even in Device Manager's hidden mode So far, nothing has worked. A wipe and reload will be out of the question

  Read the article

• Authenticating Linked Servers - SQL Server 8 to SQL Server 10

  - by jp2code

  We have an old SQL Server 2000 database that has to be kept because it is needed on our manufacturing machines. It also maintains our employee records, since they are needed on these machines for employee logins. We also have a newer SQL Server 10 database (I think this is 2008, but I'm not sure) that we are using for newer development. I have recently learned (i.e. today) that I can link the two servers. This would allow me to access the employee tables in the newer server. Following the SF post SQL Server to SQL Server Linked Server Setup, I tried adding the link. In our SQL Server 2000 machine, I got this error: Similarly, on our SQL Server 10 machine, I got this error: The messages, though worded different, probably say the same thing: I need to authenticate, somehow. We have an Active Directory, but it is on yet another server. What, exactly, should be done here? A guy HERE<< said to check the Security settings, but did not say what else to do. Both servers are set to SQL Server and Windows Authentication mode. Now what?

  Read the article

• Very slow write performance on Debian 6.0 (AMD64) with DMCRYPT/LVM/RAID1

  - by jdelic

  I'm seeing very strange performance characteristics on one of my servers. This server is running a simple two-disk software-RAID1 setup with LVM spanning /dev/md0. One of the logical volumes /dev/vg0/secure is encrypted using dmcrypt with LUKS and mounted with the sync and noatimes flag. Writing to that volume is incredibly slow at 1.8 MB/s and the CPU usage stays near 0%. There are 8 crpyto/1-8 processes running (it's a Intel Quadcore CPU). I hope that someone on serverfault has seen this before :-(. uname -a 2.6.32-5-xen-amd64 #1 SMP Tue Mar 8 00:01:30 UTC 2011 x86_64 GNU/Linux Interestingly, when I read from the device I get good performance numbers: reading without encryption: $ dd if=/dev/vg0/secure of=/dev/null bs=64k count=100000 100000+0 records in 100000+0 records out 6553600000 bytes (6.6 GB) copied, 68.8951 s, 95.1 MB/s reading with encryption: $ dd if=/dev/mapper/secure of=/dev/null bs=64k count=100000 100000+0 records in 100000+0 records out 6553600000 bytes (6.6 GB) copied, 69.7116 s, 94.0 MB/s However, when I try to write to the device: $ dd if=/dev/zero of=./test bs=64k 8809+0 records in 8809+0 records out 577306624 bytes (577 MB) copied, 321.861 s, 1.8 MB/s Also, when I read I see CPU usage, when I write, the CPU stays at almost 0% usage. Here is output of cryptsetup luksDump: LUKS header information for /dev/vg0/secure Version: 1 Cipher name: aes Cipher mode: cbc-essiv:sha256 Hash spec: sha1 Payload offset: 2056 MK bits: 256 MK digest: dd 62 b9 a5 bf 6c ec 23 36 22 92 4c 39 f8 d6 5d c1 3a b7 37 MK salt: cc 2e b3 d9 fb e3 86 a1 bb ab eb 9d 65 df b3 dd d9 6b f4 49 de 8f 85 7d 3b 1c 90 83 5d b2 87 e2 MK iterations: 44500 UUID: a7c9af61-d9f0-4d3f-b422-dddf16250c33 Key Slot 0: ENABLED Iterations: 178282 Salt: 60 24 cb be 5c 51 9f b4 85 64 3d f8 07 22 54 d4 1a 5f 4c bc 4b 82 76 48 d8 a2 d2 6a ee 13 d7 5d Key material offset: 8 AF stripes: 4000 Key Slot 1: DISABLED Key Slot 2: DISABLED Key Slot 3: DISABLED Key Slot 4: DISABLED Key Slot 5: DISABLED Key Slot 6: DISABLED Key Slot 7: DISABLED

  Read the article

• QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

  - by Horst Walter

  On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

  Read the article

• IIS 404 custom error

  - by Greg B

  I've deployed an ASP.NET 3.5 app to a 64bit Windows 2003 R2 server. In the web.config I have the following <customErrors mode="RemoteOnly" defaultRedirect="/404/"> <error statusCode="404" redirect="/404/"/> <error statusCode="500" redirect="/500/"/> </customErrors> In the website properties in IIS Manager I have set the 404 and 500 errors to Type = "URL" and the same URLs as in the web.config. I have a wildcard application map to the .NET 2.0 aspnet_isapi.dll with "Verify file exists" turned off. If I try to hit a fake .aspx file I successfully get sent to the 404 page. I belive this is because there is an explicit mapping for .aspx to the .NET DLL. If I try to access a fake directory I simply recieve a plain text response saying: The system cannot find the file specified. It would appear that these requests for directories are not being routed through the .NET pipeline, which is what I would expect (and need) to happen becuase of the wildcard application mapping. Any ideas?

  Read the article

• Configuration for Router Behind Uverse 2Wire

  - by Nori

  I have a 2Wire Uverse router(RG). I'm not particularly fond of it and want to use it as a modem only. I have a Linksys router with Tomato firmware on it and want that to be configured as the router. Most of the "guides" I've seen in my searches has been to enable DMZ Plus mode, but I don't see a way to make that work while my router has a static IP address. I played with it for quite some time yesterday and didn't see a way to get it to work. Then I ran across a setting in broadband for configuring another network. I played with that for a little bit but ran out of time and couldn't get it to work. So my question is for anyone out there who has Uverse and successfully setup a Tomato based firmware router behind the RG. How did you get it configured? I'm sure if I continued playing with it I could get it to work, but if someone out there already has it working then that would make my life easier. Thoughts? Thanks.

  Read the article

• Can't login via ssh after upgrading to Ubuntu 12.10

  - by user42899

  I have an Ubuntu 12.04LTS instance on AWS EC2 and I upgraded it to 12.10 following the instructions at https://help.ubuntu.com/community/QuantalUpgrades. After upgrading I can no longer ssh into my VM. It isn't accepting my ssh key and my password is also rejected. The VM is running, reachable, and SSH is started. The problem seems to be about the authentication part. SSH has been the only way for me to access that VM. What are my options? ubuntu@alice:~$ ssh -v -i .ssh/sos.pem [email protected] OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/ubuntu/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to www.hostname.com [37.37.37.37] port 22. debug1: Connection established. debug1: identity file .ssh/sos.pem type -1 debug1: identity file .ssh/sos.pem-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: RSA 33:33:33:33:33:33:33:33:33:33:33:33:33:33 debug1: Host '[www.hostname.com]:22' is known and matches the RSA host key. debug1: Found key in /home/ubuntu/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: .ssh/sos.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentications that can continue: publickey,password Permission denied, please try again.

  Read the article

• How to migrate a running KVM (with full disk copy) to another node?

  - by klipz

  I'm doing tests on KVM, and I'd like to see if I can make a hot migration, I mean the virtual machine won't stop running during the migration (but a few seconds of freeze is ok). I use a small cluster for my test : kvm1, kvm2, and kvmnfs. kvm1 and kvm2 runs the virtual machines kvmnfs is a NFS server, and it's mounted on /KVM on both kvm1 and kvm2 To migrate a VM (only RAM in fact) from kvm1 to kvm2, I run the same kvm command on kvm2 (with -incoming tcp:0:4444) that on kvm1, then I use "migrate -d tcp:kvm2:4444" : It works great, since the VM file is common to both machines. Now, I wan't to make a full migration (RAM + disk) of a local VM file (no more NFS) of kvm1 to kvm2. I tried to create an empty file, with touch, on kvm2 and use the same kvm command line + the "-incoming ..."). Then on kvm1 I use "migrate -d tcp:kvm2:4444" : It copies everything, then... the VM fails (any I/O disk gives an I/O error) ! And my VM file on kvm2, the one I created with touch, as still a size of 0 bytes. What am I doing wrong ? What is the exact command to use on kvm2 ? And what is the command to launch, in the monitoring mode, on kvm1 ?

  Read the article

• Can OpenVPN invoke DHCP Client?

  - by Ency

  I have got working VPN connection through openvpn, but I would like to use also my DHCP server and not openvpn's push feature. Currently everything works fine, but I have to manually start dhcp client, eg. dhclient tap0 and I get IP and other important stuff from my DHCP, is there any directive which start DHCP Client when connection is established? There is my client's config: remote there.is.server.com float dev tap tls-client #pull port 1194 proto tcp-client persist-tun dev tap0 #ifconfig 192.168.69.201 255.255.255.0 #route-up "dhclient tap0" #dhcp-renew ifconfig 0.0.0.0 255.255.255.0 ifconfig-noexec ifconfig-nowarn ca /etc/openvpn/ca.crt cert /etc/openvpn/encyNtb_openvpn_client.crt key /etc/openvpn/encyNtb_openvpn_client.key dh /etc/openvpn/dh-openvpn.dh ping 10 ping-restart 120 comp-lzo verb 5 log-append /var/log/openvpn.log Here comes server's config: mode server tls-server dev tap0 local servers.ip.here port 1194 proto tcp-server server-bridge # Allow comunication between clients client-to-client # Allowing duplicate users per one certificate duplicate-cn # CA Certificate, VPN Server Certificate, key, DH and Revocation list ca /etc/ssl/CA/certs/ca.crt cert /etc/ssl/CA/certs/openvpn_server.crt key /etc/ssl/CA/private/openvpn_server.key dh /etc/ssl/CA/dh/dh-openvpn.dh crl-verify /etc/ssl/CA/crl.pem # When no response is recieved within 120seconds, client is disconected keepalive 10 60 persist-tun persist-key user openvpn group openvpn # Log and Connected clients file log-append /var/log/openvpn verb 3 status /var/run/openvpn/vpn.status 10 # Compression comp-lzo #Push data to client push "route-gateway 192.168.69.1" push "redirect-gateway def1"

  Read the article

• Can't do more than one activity at a time after switching modems

  - by vallorn

  I had to replace the Motorola 2210 DSL modem that I got when I signed up for AT&T DSL Direct a few years ago. The modem kept randomly restarting and it eventually gave out on me. I am assuming overheating was the cause here because it was almost too hot to touch. In any case, I replaced it with a Netgear DM111PSP. It works fine but I can't do more than one activity at a time with it. If my wife is watching Netflix, there is a noticeable delay/latency when trying to view web sites. It's even worse if I try to play an on-line game while she's streaming; the game is basically unplayable. The odd thing is, the only other activity I can do while she's streaming is stream another Netflix show myself. There is no delay when doing that, no buffering either. I'm not a networking guy so maybe there is an explanation for it but I find that kind of odd. I've tried using QoS through my Buffalo N600 wireless router and it doesn't seem to help. With the old Motorola modem, she could be watching Netflix while I play a game and everything worked just fine. Is there anything I can check or reconfigure possibly on the modem that would account for this? Should I just ditch the Netgear and get another modem instead? I have the Netgear modem connected to the Buffalo router in a bridged mode. Its the same exact setup as I had with the Motorola and as far as I can tell, it's not the router that is the cause.

  Read the article

• OpenVPN: ifup tap0 drops all connections

  - by raspi

  I'm trying to create star shaped "virtual" LAN with OpenVPN which is not connected to physical network. ie. tap0 packets should not go to eth0. Packet should only go through OpenVPN to connected clients. This setup works with my OpenVPN testing machine which runs Virtual Box but not on my actual server which is running on top of Xen. Both servers are running Ubuntu Intrepid. /etc/network/interfaces: iface tap0 inet manual address 10.10.10.1 netmask 255.255.255.0 gateway 10.10.10.1 /etc/openvpn/server.conf mode server tls-server port 1194 proto udp dev tap client-to-client ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/servername.crt key /etc/openvpn/easy-rsa/keys/servername.key dh /etc/openvpn/easy-rsa/keys/dh384.pem ifconfig-pool-persist ipp.txt server-bridge 10.10.10.1 255.255.255.0 10.10.10.128 10.10.10.250 push .route 10.10.10.1 255.255.255.0 keepalive 5 60 comp-lzo persist-key persist-tun status /var/log/openvpn-status.log log-append /var/log/openvpn.log verb 3 user nobody group nogroup ifup tap0 on Virtual Box: everything ok, SSH keeps running. But on Xen SSH connection drops and I have to reboot whole machine. What I'm missing?

  Read the article

< Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >