Search Results

Search found 10931 results on 438 pages for 'struts config'.

Page 395/438 | < Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >

• ZFS Recover from Faulted Pool State

  - by nickv2002

  I have a six disk ZFS raidz1 pool and had a recent failure requiring a disk replacement. No problem normally, but this time my server hardware died before I could do the replacement (but after and unrelated to the drive failure as far as I can tell). I was able to get another machine from a friend to rebuild the system, but in the process of moving my drives over I had to swap their cables around a bunch until I got the right configuration where the remaining 5 good disks were seen as online. This process seems to have generated some checksum errors for the pool/raidz. I have the 5 remaining drives set up now and a good drive installed and ready to take the place of the drive that died. However, since my pool state is FAULTED I'm unable to do the replacement. root@zfs:~# zpool replace tank 1298243857915644462 /dev/sdb cannot open 'tank': pool is unavailable Is there any way to recover from this error? I would think that having 5 of the 6 drives online would be enough to rebuild the right data, but that doesn't seem to be enough now. Here's the status log of my pool: root@zfs:~# zpool status tank pool: tank state: FAULTED status: One or more devices could not be used because the label is missing or invalid. There are insufficient replicas for the pool to continue functioning. action: Destroy and re-create the pool from a backup source. see: http://zfsonlinux.org/msg/ZFS-8000-5E scan: none requested config: NAME STATE READ WRITE CKSUM tank FAULTED 0 0 1 corrupted data raidz1-0 ONLINE 0 0 8 sdd ONLINE 0 0 0 sdf ONLINE 0 0 0 sdh ONLINE 0 0 0 1298243857915644462 UNAVAIL 0 0 0 was /dev/sdb1 sde ONLINE 0 0 0 sdg ONLINE 0 0 0 Update (10/31): I tried to export and re-import the array a few times over the past week and wasn't successful. First I tried: zpool import -f -R /tank -N -o readonly=on -F tank That produced this error immediately: cannot import 'tank': I/O error Destroy and re-create the pool from a backup source. I added the '-X' option to the above command to try to make it check the transaction log. I let that run for about 48 hours before giving up because it had completely locked up my machine (I was unable to log in locally or via the network). Now I'm trying a simple zpool import tank command and that seems to run for a while with no output. I'll leave it running overnight to see if it outputs anything.

  Read the article

• Reach self hosted server from LAN

  - by Freefri

  I have a self hosted server with Apache2 pointed with the domain example.com. I have also some virtual servers www.example.com, cloud.examle.com, etc. This server is in my LAN, and when I try to acces to my server within the lan throw www.examle.com y get my router's configuration page. From outside the LAN www.example.com and cloud.examle.com works properly. From inside the LAN 192.168.1.33 (server internal IP) shows the default webpage (www.examle.com), but I can not get cloud.examle.com I also have a LAN name server in 192.168.1.33 with bind9. I set up my gateway 192.168.1.1 with my LAN-NS as primary NS I solve this problem creating a new dns zone in the NS. This are my config files: ;ZONE-1 $ORIGIN . $TTL 86400 ; 1 day home.lan. IN SOA server.home.lan. hostmaster.home.lan. ( 2008080901 ; serial 8H ; refresh 4H ; retry 4W ; expire 1D ; minimum ) home.lan. IN NS server.home.lan. $ORIGIN home.lan. ; Set the address for localhost.home.lan localhost IN A 127.0.0.1 router IN A 192.168.1.1 server IN A 192.168.1.33 mypc IN A 192.168.1.132 ;ZONE-2 $ORIGIN . $TTL 86400 ; 1 day example.com. IN SOA www.example.com hostmaster.home.lan. ( 2008080902 ; serial 8H ; refresh 4H ; retry 4W ; expire 1D ; minimum ) example.com. IN NS 192.168.1.33 $ORIGIN examle.com. localhost IN A 127.0.0.1 www IN A 192.168.1.33 cloud IN A 192.168.1.33 My DNS and my names are working properly now My question are: What do you think about my solution? Can I change the A zone with CNAME to server.home.lan (this is the domain in the LAN to the server)? How can I set a default IP for all my whatever.example.com?

  Read the article

• Laptops on Windows Domain sometimes have problems accessing internet when off-site

  - by FSUScoot

  Hi all-- We've had this problem for a long time. When users travel, sometimes they can't get internet access from a wired or wireless connection. Here are a couple examples: 1) A user goes to a hotel and tries to access the wireless in their room. They can connect to the access point. They open a web browser and they can't get re-directed to the hotel's login page. Because they can't log in, there's no internet access. 2) A user goes to another laboratory/university and tries to access the wired network. They connect, link is fine, PC gets IP from DHCP but no internet access. There's no login page to be re-directed to. It should just "work". What I've found is that it's a DNS issue. Because the computer is on a Windows Domain, it seems it MUST use our DNS servers. Even if you connect to an outside network and do an ipconfig /all, it looks like everything is ok. It'll even show their DNS servers listed in the config. The computer just won't use the other network's DNS server. I found a reg key that keeps our DNS servers listed and it seems that they take priority every time: HKLM\SOFTWARE\Policies\Microsoft\Windows NT\DNSClient All the values under that key are for our AD domain. NameServer and Searchlist never change. What I've found is if the user edits the NameServer string and puts the DNS server of the network they're on, everything works just fine. They get re-directed to the hotel's correct login page or their internet access starts working. It's only a problem if the network they're on blocks outside DNS or a hotel that uses an internal name in their front page redirection that only their DNS server knows about, i.e., not public. If the re-direct page starts with an IP, like 10.10.10.10, it'll work just fine. Obviously this isn't a fix for everyone. Most of my users are pretty knowledgeable so it’s easy for me to walk them through or send them a .reg file that they can edit and run. This problem isn't limited to Windows 7. It was like this with XP as well. It's not hardware related. The problem exists on both wired and wireless, Intel or Broadcom, laptops or desktops. Anyone else have this problem? Is there a GPO I can change that I missed? Got a good work-around for this? Thanks for any help!

  Read the article

• Weird nfs performance: 1 thread better than 8, 8 better than 2!

  - by Joe

  I'm trying to determine the cause of poor nfs performance between two Xen Virtual Machines (client & server) running on the same host. Specifically, the speed at which I can sequentially read a 1GB file on the client is much lower than what would be expected based on the measured network connection speed between the two VMs and the measured speed of reading the file directly on the server. The VMs are running Ubuntu 9.04 and the server is using the nfs-kernel-server package. According to various NFS tuning resources, changing the number of nfsd threads (in my case kernel threads) can affect performance. Usually this advice is framed in terms of increasing the number from the default of 8 on heavily-used servers. What I find in my current configuration: RPCNFSDCOUNT=8: (default): 13.5-30 seconds to cat a 1GB file on the client so 35-80MB/sec RPCNFSDCOUNT=16: 18s to cat the file 60MB/s RPCNFSDCOUNT=1: 8-9 seconds to cat the file (!!?!) 125MB/s RPCNFSDCOUNT=2: 87s to cat the file 12MB/s I should mention that the file I'm exporting is on a RevoDrive SSD mounted on the server using Xen's PCI-passthrough; on the server I can cat the file in under seconds ( 250MB/s). I am dropping caches on the client before each test. I don't really want to leave the server configured with just one thread as I'm guessing that won't work so well when there are multiple clients, but I might be misunderstanding how that works. I have repeated the tests a few times (changing the server config in between) and the results are fairly consistent. So my question is: why is the best performance with 1 thread? A few other things I have tried changing, to little or no effect: increasing the values of /proc/sys/net/ipv4/ipfrag_low_thresh and /proc/sys/net/ipv4/ipfrag_high_thresh to 512K, 1M from the default 192K,256K increasing the value of /proc/sys/net/core/rmem_default and /proc/sys/net/core/rmem_max to 1M from the default of 128K mounting with client options rsize=32768, wsize=32768 From the output of sar -d I understand that the actual read sizes going to the underlying device are rather small (<100 bytes) but this doesn't cause a problem when reading the file locally on the client. The RevoDrive actually exposes two "SATA" devices /dev/sda and /dev/sdb, then dmraid picks up a fakeRAID-0 striped across them which I have mounted to /mnt/ssd and then bind-mounted to /export/ssd. I've done local tests on my file using both locations and see the good performance mentioned above. If answers/comments ask for more details I will add them.

  Read the article

• nginx rewrite for wikkawiki

  - by Hans

  Just setup WikkaWiki on my server, I have been trying to have the links go from wiki.mysite.info/wikka.php?wakka=Start into wiki.mysite.info/DotMG. I tried following their guide at http://docs.wikkawiki.org/ModRewrite, however it seems incomplete and outdated. Furthermore, as of version 1.3.2 base_url isn't even manually configurable from the wikka.config.php file. I am using version 1.3.2 of WikkaWiki. My nginx virtual hosts file contains: server { listen 80; server_name wiki.mysite.info; root /usr/share/nginx/wikka/; access_log /usr/share/nginx/.access/wikka; error_log /usr/share/nginx/.error/wikka error; location / { index index.php; try_files $uri $uri/ @wikka; } location @wikka { rewrite ^(.*/[^\./]*[^/])$ $1/ last; rewrite ^(.*)$ /wikka.php?wakka=$1 last; } location ~* \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } Thus far it works, I can go to wiki.mysite.info/APage and it'll display that page, however it doesn't work on all pages, sometime the browser simply downloads the page (For some reason it always downloads the Start page). Also when I go to wiki.mysite.info/ it downloads the wikka.php file... Furthermore, the links on the wiki have the wikka.php?wakka= so whenever I navigate around the wiki, it goes back to being wiki.mysite.info/wikka.php?wakka=APage. I think something is wrong with my rewrite but I can't say for sure. Contents of the fastcgi_params: fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_FILENAME $request_filename; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; fastcgi_param HTTPS $server_https; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200;

  Read the article

• MySQL won't start, reinstall fails on Ubuntu 12.04

  - by Evils

  My problem started yesterday night when I tried to change the my.cnf config on my ubuntu 12.04 x64 System. I simply tried to changed the bind-address parameter from 127.0.0.1 to 0.0.0.0. A simple restart after a reboot gave this error: stop: Unknown instance: start: Job failed to start I tried to start mysql then by using 'mysqld' which outputs this: 130701 11:05:59 [Note] Plugin 'FEDERATED' is disabled. mysqld: Table 'mysql.plugin' doesn't exist 130701 11:05:59 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 130701 11:05:59 InnoDB: The InnoDB memory heap is disabled 130701 11:05:59 InnoDB: Mutexes and rw_locks use GCC atomic builtins 130701 11:05:59 InnoDB: Compressed tables use zlib 1.2.3.4 130701 11:05:59 InnoDB: Initializing buffer pool, size = 128.0M 130701 11:05:59 InnoDB: Completed initialization of buffer pool 130701 11:05:59 InnoDB: highest supported file format is Barracuda. 130701 11:05:59 InnoDB: Waiting for the background threads to start 130701 11:06:00 InnoDB: 5.5.31 started; log sequence number 1595675 130701 11:06:00 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 130701 11:06:00 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 130701 11:06:00 [Note] Server socket created on IP: '127.0.0.1'. 130701 11:06:00 [ERROR] Can't start server : Bind on unix socket: Permission denied 130701 11:06:00 [ERROR] Do you already have another mysqld server running on socket: /var/run/mysqld/mysqld.sock ? 130701 11:06:00 [ERROR] Aborting 130701 11:06:00 InnoDB: Starting shutdown... 130701 11:06:00 InnoDB: Shutdown completed; log sequence number 1595675 130701 11:06:00 [Note] mysqld: Shutdown complete Meanwhile I already tried to reinstall and purge the complete mysql package which results in another error which says that dpkg cant change the admins password. While this error appeared another error came with it. When trying to install something new with apt, it always says 'fopen: permission denied' right after it tries to update my man-db. This is my dmesg output: [ 6879.687998] type=1400 audit(1372669683.397:36): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=9336 comm="apparmor_parser" [ 6881.323215] init: mysql main process (9340) terminated with status 1 [ 6881.323316] init: mysql respawning too fast, stopped Any help will be appreciated as this is a productive server which renders useless without mysql.

  Read the article

• Restarting or stopping apache results in waiting forever

  - by steko

  I have two simple WSGI apps running on top of mod_wsgi and apache2 on a test development server. There is no mod_python on this machine. The WSGI configuration is as follows WSGIDaemonProcess tops stack-size=524288 maximum-requests=5 WSGIScriptAlias /tops /home/ubuntu/tops-cloud/tops.wsgi <Directory /home/ubuntu/tops-cloud> WSGIProcessGroup tops WSGIApplicationGroup %{GLOBAL} Order deny,allow Allow from all </Directory> WSGIDaemonProcess flaskal maximum-requests=5 WSGIScriptAlias /c14 /home/ubuntu/c14/flaskal/flaskal.wsgi <Directory /home/ubuntu/c14/flaskal> WSGIProcessGroup flaskal WSGIApplicationGroup %{GLOBAL} Order deny,allow Allow from all </Directory> If I make changes to the app, I need to restart the web server, so I would expect that a simple sudo service apache2 restart does what I need. Same goes for any changes to the config (e.g. number of maximum requests, etc). Instead, it never ends "waiting", like this: $ sudo service apache2 restart * Restarting web server apache2 ... waiting .................................................. until I just do CTRL-C. At that point, the only way to resume a working server is to kill the process and restart it, not very convenient. The same happens with the stop command. The error logs at the "debug" level show the following lines after a failed restart [Wed Nov 14 21:55:19 2012] [notice] caught SIGTERM, shutting down [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=9047): Shutdown requested 'tops'. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=9047): Stopping process 'tops'. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=9047): Destroying interpreters. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=9047): Cleanup interpreter ''. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=9047): Terminating Python. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=8920): Shutdown requested 'flaskal'. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=8920): Stopping process 'flaskal'. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=8920): Destroying interpreters. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=8920): Cleanup interpreter ''. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=8920): Terminating Python. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=8920): Python has shutdown. [Wed Nov 14 21:55:19 2012] [info] mod_wsgi (pid=9047): Python has shutdown. If I then try to restart again (with the process still running), I get the following error: * Restarting web server apache2 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs Action 'start' failed. The Apache error log may have more information. Unfortunately the Apache error log doesn't have anything. When apache2 is running properly, both apps work without any problem.

  Read the article

• OpenVPN Chaining

  - by noderunner

  I'm trying to set up an OpenVPN "chain", similar to what is described here. I have two separate networks, A and B. Each network has an OpenVPN server using a standard "road warrior" or "client/server" approach. A client can connect to either one for access to the hosts/services on that respective network. But server A and B are also connected to each other. The servers on each network have a "site-to-site" connection between the two. What I'm trying to accomplish, is the ability to connect to network A as a client, and then make connections with hosts on network B. I'm using tun/routing for all of the VPN connections. The "chain" looks something like this: [Client] --- [Server A] --- [Server A] --- [Server B] --- [Server B] --- [Host B] (tun0) (tun0) (tun1) (tun0) (eth0) (eth0) The whole idea is that server A should route traffic destined to network B through the "site-to-site" VPN set up on tun1 when a client from tun0 tries to connect. I did this simply by setting up two connection profiles on server A. One profile is a standard server config running on tun0, defining a virtual client network, IP address pool, pushing routes, etc. The other is a client connection to Server B running on tun1. With ip_forwarding enabled, I then simply added a "push route" to the clients advertising a route to network B. On server A, this seems to work when I look at tcpdump output. If I connect as a client, and then ping a host on network B, I can see the traffic getting passed from tun0 to tun1 on Server A: tcpdump -nSi tun1 icmp The weird thing is that I don't see Server B receiving that traffic through the tunnel. It's as if Server A is sending it through the site-to-site connection like it should, but server B is completely ignoring it. When I look for the traffic on Server B, it simply isn't there. A ping from Server A -- Host B works fine. But a ping from a client connected to Server A to host B does not. I'm wondering if Server B is ignoring the traffic because the source IP does not match the client IP pool that it hands out to clients? Does anyone know if I need to do something on Server B in order for it to see the traffic? This is a complicated problem to explain, so thanks if you stuck with me this far.

  Read the article

• Local dns for testing websites using mobile devices

  - by Morpheu5

  Hi. I have no idea where to start from so sorry in advance if this topic has already been discussed. I usually develop web sites using my laptop as a development server, and recently I needed to test a web site using various mobile devices that can connect via wifi. Having no real AP, I set up a ad-hoc network using my laptop's wireless card and the devices can correctly browse the Internet and access the laptop's web server. The setup is as follows: subnet: 192.168.1.0/24 gateway to the Internet (wired adsl router/modem): 192.168.1.1 laptop: 192.168.1.64 (eth0, wired if connected to the gateway) and 192.168.1.32 (eth1, wifi if somewhat bridged to eth0) mobile devices (same for all, I only use one of them at any time for simplicity): 192.168.1.11 with default gw 192.168.1.1 Now, if I open either 192.168.1.32 or 192.168.1.64 from the mobile devices, I correctly get the default host of my Apache configuration. However I usually work with virtual hosts for many practical reasons, one of which being Drupal's peculiar implementation of multi-sites. For those who don't know how this works, Drupal takes the request's hostname and searches into its sites/ subdirectories for an appropriate configuration file. So, for example, suppose I request www.example.com, then Drupal would search for a config file in the following directories: sites/www.example.com/ sites/example.com/ sites/com/ sites/default/ So I decided to adopt the following style of virtual hosts: if the website I'm working on will be accessible using www.example.com I set up a sites/www.example.com/ directory and create a virtual host for local.www.example.com so Drupal have no trouble finding it. I've been told this is suboptimal from a dns point of view since I'd have to create an authoritative entry for example.com and turn Bind on only when I'm supposed to access the local copy, which is weird. However, if this is the only path I can follow, I still have some problems with Bind's configuration, as I couldn't find any guide that tells me in a clear, noob-friendly way, how to set up such an entry. On the other hand, I was wondering if I could set up an authoritative entry for local, so I could access www.example.com.local and tell in some way (which I don't even know if this is possible) Apache to put www.example.com instead of www.example.com.local in the relevant environment variable. Anyway, I have a last problem, sort of: when I launch Bind in debug mode with high verbosity, and make 192.168.1.32 as the primary dns for the devices, the output doesn't say anything about requests being made from the devices to Bind, so I'm not even sure it comes into play. As you can see, I'm a complete noob at these matters, but I'm eager to learn, so any help/pointer will be appreciated.

  Read the article

• Why is my concurrency capacity so low for my web app on a LAMP EC2 instance?

  - by AMF

  I come from a web developer background and have been humming along building my PHP app, using the CakePHP framework. The problem arose when I began the ab (Apache Bench) testing on the Amazon EC2 instance in which the app resides. I'm getting pretty horrendous average page load times, even though I'm running a c1.medium instance (2 cores, 2GB RAM), and I think I'm doing everything right. I would run: ab -n 200 -c 20 http://localhost/heavy-but-view-cached-page.php Here are the results: Concurrency Level: 20 Time taken for tests: 48.197 seconds Complete requests: 200 Failed requests: 0 Write errors: 0 Total transferred: 392111200 bytes HTML transferred: 392047600 bytes Requests per second: 4.15 [#/sec] (mean) Time per request: 4819.723 [ms] (mean) Time per request: 240.986 [ms] (mean, across all concurrent requests) Transfer rate: 7944.88 [Kbytes/sec] received While the ab test is running, I run VMStat, which shows that Swap stays at 0, CPU is constantly at 80-100% (although I'm not sure I can trust this on a VM), RAM utilization ramps up to about 1.6G (leaving 400M free). Load goes up to about 8 and site slows to a crawl. Here's what I think I'm doing right on the code side: In Chrome browser uncached pages typically load in 800-1000ms, and cached pages load in 300-500ms. Not stunning, but not terrible either. Thanks to view caching, there might be at most one DB query per page-load to write session data. So we can rule out a DB bottleneck. I have APC on. I am using Memcached to serve the view cache and other site caches. xhprof code profiler shows that cached pages take up 10MB-40MB in memory and 100ms - 1000ms in wall time. Pages that would be the worst offenders would look something like this in xhprof: Total Incl. Wall Time (microsec): 330,143 microsecs Total Incl. CPU (microsecs): 320,019 microsecs Total Incl. MemUse (bytes): 36,786,192 bytes Total Incl. PeakMemUse (bytes): 46,667,008 bytes Number of Function Calls: 5,195 My Apache config: KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 3 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 120 MaxRequestsPerChild 1000 </IfModule> Is there something wrong with the server? Some gotcha with the EC2? Or is it my code? Some obvious setting I should look into? Too many DNS lookups? What am I missing? I really want to get to 1,000 concurrency capacity, but at this rate, it ain't gonna happen.

  Read the article

• How to reliably map vSphere disks <-> Linux devices

  - by brianmcgee

  Task at hand After a virtual disk has been added to a Linux VM on vSphere 5, we need to identify the disks in order to automate the LVM storage provision. The virtual disks may reside on different datastores (e.g. sas or flash) and although they may be of the same size, their speed may vary. So I need a method to map the vSphere disks to Linux devices. Ideas Through the vSphere API, I am able to get the device info: Data Object Type: VirtualDiskFlatVer2BackingInfo Parent Managed Object ID: vm-230 Property Path: config.hardware.device[2000].backing Properties Name Type Value ChangeId string Unset contentId string "d58ec8c12486ea55c6f6d913642e1801" datastore ManagedObjectReference:Datastore datastore-216 (W5-CFAS012-Hybrid-CL20-004) deltaDiskFormat string "redoLogFormat" deltaGrainSize int Unset digestEnabled boolean false diskMode string "persistent" dynamicProperty DynamicProperty[] Unset dynamicType string Unset eagerlyScrub boolean Unset fileName string "[W5-CFAS012-Hybrid-CL20-004] l****9-000001.vmdk" parent VirtualDiskFlatVer2BackingInfo parent split boolean false thinProvisioned boolean false uuid string "6000C295-ab45-704e-9497-b25d2ba8dc00" writeThrough boolean false And on Linux I may read the uuid strings: [root@lx***** ~]# lsscsi -t [1:0:0:0] cd/dvd ata: /dev/sr0 [2:0:0:0] disk sas:0x5000c295ab45704e /dev/sda [3:0:0:0] disk sas:0x5000c2932dfa693f /dev/sdb [3:0:1:0] disk sas:0x5000c29dcd64314a /dev/sdc As you can see, the uuid string of disk /dev/sda looks somehow familiar to the string that is visible in the VMware API. Only the first hex digit is different (5 vs. 6) and it is only present to the third hyphen. So this looks promising... Alternative idea Select disks by controller. But is it reliable that the ascending SCSI Id also matches the next vSphere virtual disk? What happens if I add another DVD-ROM drive / USB Thumb drive? This will probably introduce new SCSI devices in between. Thats the cause why I think I will discard this idea. Questions Does someone know an easier method to map vSphere disks and Linux devices? Can someone explain the differences in the uuid strings? (I think this has something to do with SAS adressing initiator and target... WWN like...) May I reliably map devices by using those uuid strings? How about SCSI virtual disks? There is no uuid visible then... This task seems to be so obvious. Why doesn't Vmware think about this and simply add a way to query the disk mapping via Vmware Tools?

  Read the article

• vBulletin 5 + lighthttpd url rewriting

  - by Boots

  I'm trying to get vBulletin 5 up and running under lighttpd but I'm having some problems with url rewriting. Here is the apache .htaccess provided by vBulletin. <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php?routestring=$1 [L,QSA] #needed because admincp is an actual directory. RewriteRule ^(admincp/)$ index.php?routestring=$1 [L,QSA] </IfModule> If this helps, this is the IIS config provided by vBulletin <?xml version="1.0" encoding="UTF-8"?> <!-- This file is to support redirection in IIS. It is harmless if you are running under Apache --> <configuration> <system.webServer> <rewrite> <rules> <rule name="Main Redirect" stopProcessing="true"> <match url="^(.*)$" ignoreCase="false" /> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_FILENAME}" matchType="IsFile" ignoreCase="false" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" ignoreCase="false" negate="true" /> </conditions> <action type="Rewrite" url="index.php/{R:1}" /> </rule> <rule name="Admincp" stopProcessing="true"> <match url="^(admincp/)$" ignoreCase="false" /> <action type="Rewrite" url="index.php/{R:1}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Anyone have any suggestions as to the lighttpd url.rewrite equivalent? All my experiments have failed thus far. I'm running lighttpd-1.4.31-1 I tried this but it didn't work. I think it has something to do with me not properly emulating [QS] in the .htaccess url.rewrite-once = ("^(.*)$" => "index.php?routestring=$1", "^(admincp/)$)" => "index.php?routestring=$1") This has gotten me closer but not fully functional yet. url.rewrite-if-not-file = ("^(.*)$" => "index.php?routestring=$1", "^(admincp/)$)" => "index.php?routestring=$1")

  Read the article

• Convert apache rewrite rules to nginx

  - by Shiyu Sekam

  I want to migrate an Apache setup to Nginx, but I can't get the rewrite rules working in Nginx. I had a look on the official nginx documentation, but still some trouble converting it. http://nginx.org/en/docs/http/converting_rewrite_rules.html I've used http://winginx.com/en/htaccess to convert my rules, but this just works partly. The / part looks okay, the /library part as well, but the /public part doesn't work at all. Apache part: ServerAdmin webmaster@localhost DocumentRoot /srv/www/Web Order allow,deny Allow from all RewriteEngine On RewriteRule ^$ public/ [L] RewriteRule (.*) public/$1 [L] Order Deny,Allow Deny from all RewriteEngine On RewriteCond %{QUERY_STRING} ^pid=([0-9]*)$ RewriteRule ^places(.*)$ index.php?url=places/view/%1 [PT,L] # Extract search query in /search?q={query}&l={location} RewriteCond %{QUERY_STRING} ^q=(.*)&l=(.*)$ RewriteRule ^(.*)$ index.php?url=search/index/%1/%2 [PT,L] # Extract search query in /search?q={query} RewriteCond %{QUERY_STRING} ^q=(.*)$ RewriteRule ^(.*)$ index.php?url=search/index/%1 [PT,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # Rewrite all other URLs to index.php/URL RewriteRule ^(.*)$ index.php?url=$1 [PT,L] Order deny,allow deny from all ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn AddHandler php5-fcgi .php Action php5-fcgi /php5-fcgi Alias /php5-fcgi /usr/lib/cgi-bin/php5-fcgi FastCgiExternalServer /usr/lib/cgi-bin/php5-fcgi -socket /var/run/php5-fpm.sock -pass-header Authorization CustomLog ${APACHE_LOG_DIR}/access.log combined Nginx config: server { #listen 80; ## listen for ipv4; this line is default and implied root /srv/www/Web; index index.html index.php; server_name localhost; location / { rewrite ^/$ /public/ break; rewrite ^(.*)$ /public/$1 break; } location /library { deny all; } location /public { if ($query_string ~ "^pid=([0-9]*)$"){ rewrite ^/places(.*)$ /index.php?url=places/view/%1 break; } if ($query_string ~ "^q=(.*)&l=(.*)$"){ rewrite ^(.*)$ /index.php?url=search/index/%1/%2 break; } if ($query_string ~ "^q=(.*)$"){ rewrite ^(.*)$ /index.php?url=search/index/%1 break; } if (!-e $request_filename){ rewrite ^(.*)$ /index.php?url=$1 break; } } location ~ \.php$ { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } } I haven't written the original ruleset, so I've a hard time converting it. Would you mind giving me a hint how to do it easily or can you help me to convert it, please? I really want to switch over to php5-fpm and nginx :) Thanks

  Read the article

• Reliable file copy (move) process - mostly Unix/Linux

  - by mfinni

  Short story : We have a need for a rock-solid reliable file mover process. We have source directories that are often being written to that we need to move files from. The files come in pairs - a big binary, and a small XML index. We get a CTL file that defines these file bundles. There is a process that operates on the files once they are in the destination directory; that gets rid of them when it's done. Would rsync do the best job, or do we need to get more complex? Long story as follows : We have multiple sources to pull from : one set of directories are on a Windows machine (that does have Cygwin and an SSH daemon), and a whole pile of directories are on a set of SFTP servers (Most of these are also Windows.) Our destinations are a list of directories on AIX servers. We used to use a very reliable Perl script on the Windows/Cygwin machine when it was our only source. However, we're working on getting rid of that machine, and there are other sources now, the SFTP servers, that we cannot presently run our own scripts on. For security reasons, we can't run the copy jobs on our AIX servers - they have no access to the source servers. We currently have a homegrown Java program on a Linux machine that uses SFTP to pull from the various new SFTP source directories, copies to a local tmp directory, verifies that everything is present, then copies that to the AIX machines, and then deletes the files from the source. However, we're finding any number of bugs or poorly-handled error checking. None of us are Java experts, so fixing/improving this may be difficult. Concerns for us are: With a remote source (SFTP), will rsync leave alone any file still being written? Some of these files are large. From reading the docs, it seems like rysnc will be very good about not removing the source until the destination is reliably written. Does anyone have experience confirming or disproving this? Additional info We will be concerned about the ingestion process that operates on the files once they are in the destination directory. We don't want it operating on files while we are in the process of copying them; it waits until the small XML index file is present. Our current copy job are supposed to copy the XML file last. Sometimes the network has problems, sometimes the SFTP source servers crap out on us. Sometimes we typo the config files and a destination directory doesn't exist. We never want to lose a file due to this sort of error. We need good logs If you were presented with this, would you just script up some rsync? Or would you build or buy a tool, and if so, what would it be (or what technologies would it use?) I (and others on my team) are decent with Perl.

  Read the article

• vBulletin 5 + lighttpd url rewriting

  - by Boots

  I'm trying to get vBulletin 5 up and running under lighttpd but I'm having some problems with url rewriting. Here is the apache .htaccess provided by vBulletin. <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php?routestring=$1 [L,QSA] #needed because admincp is an actual directory. RewriteRule ^(admincp/)$ index.php?routestring=$1 [L,QSA] </IfModule> If this helps, this is the IIS config provided by vBulletin <?xml version="1.0" encoding="UTF-8"?> <!-- This file is to support redirection in IIS. It is harmless if you are running under Apache --> <configuration> <system.webServer> <rewrite> <rules> <rule name="Main Redirect" stopProcessing="true"> <match url="^(.*)$" ignoreCase="false" /> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_FILENAME}" matchType="IsFile" ignoreCase="false" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" ignoreCase="false" negate="true" /> </conditions> <action type="Rewrite" url="index.php/{R:1}" /> </rule> <rule name="Admincp" stopProcessing="true"> <match url="^(admincp/)$" ignoreCase="false" /> <action type="Rewrite" url="index.php/{R:1}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Anyone have any suggestions as to the lighttpd url.rewrite equivalent? All my experiments have failed thus far. I'm running lighttpd-1.4.31-1 I tried this but it didn't work. I think it has something to do with me not properly emulating [QS] in the .htaccess url.rewrite-once = ("^(.*)$" => "index.php?routestring=$1", "^(admincp/)$)" => "index.php?routestring=$1") This has gotten me closer but not fully functional yet. url.rewrite-if-not-file = ("^(.*)$" => "index.php?routestring=$1", "^(admincp/)$)" => "index.php?routestring=$1")

  Read the article

• SharePoint 2010 – Central Admin tooling to create host header site collections

  - by eJugnoo

  Just like SharePoint 2007, you can create host-header based site collections in SharePoint 2010 as well. It means, that you do not necessarily need to create a site-collection under a managed path like /sites/, you can create multiple root-level site collections on same web-application/port by using host-header site collections. All you need to do is point your domain or sub-domain to your web-application and create a matching site-collection that you want. But, just like in 2007, it is something that you do by using STSADM, and is not available on Central Admin UI in 2010 as well. Yeah, though you can now also use PowerShell to create one: C:\PS>$w = Get-SPWebApplication http://sitename   C:\PS>New-SPSite http://www.contoso.com -OwnerAlias "DOMAIN\jdoe" -HostHeaderWebApplication $w -Title "Contoso" -Template "STS#0"   This example creates a host header site collection. Because the template is provided, the root Web of this site collection will be created. .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } I’ve been playing with WCM in SharePoint 2010 more and more, and for that I preferred creating hosts file entries for desired domains and create site-collections by those headers – in my dev environment. I used PowerShell initially, but then got interested to build my own UI on Central Admin instead. Developed with Visual Studio 2010 So I used new Visual Studio 2010 tooling to create an empty SharePoint 2010 project. Added an application page (there is no option to add _Admin page item in VS 2010 RC), that got created in Layouts “mapped” folder. Created a new Admin mapped folder for 14-“hive”, and moved my new page there instead. Yes, I didn’t change the base class for page, its just that it runs under _admin, but it is indeed a LayoutsPageBase inherited page. To introduce a action-link in Central Admin console, I created following element: 1: <Elements xmlns="http://schemas.microsoft.com/sharepoint/"> 2: <CustomAction 3: Id="CreateSiteByHeader" 4: Location="Microsoft.SharePoint.Administration.Applications" 5: Title="Create site collections by host header" 6: GroupId="SiteCollections" 7: Sequence="15" 8: RequiredAdmin="Delegated" 9: Description="Create a new top-level web site, by host header" > 10: <UrlAction Url="/_admin/OfficeToolbox/CreateSiteByHeader.aspx" /> 11: </CustomAction> 12: </Elements> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Used Reflector to understand any special code behind createpage.aspx, and created a new for our purpose – CreateSiteByHeader.aspx. From there I quickly created a similar code behind, without all the fancy of Farm Config Wizard handling and dealt with alternate implementations of sealed classes! Goal was to create a professional looking and OOB-type experience. I also added Regex validation to ensure user types a valid domain name as header value. Below is the result…   Release @ Codeplex I’ve released to WSP on OfficeToolbox @ Codeplex, and you can download from here. Hope you find it useful… -- Sharad

  Read the article

• jenkins-maven-android when running throwing the error "android-sdk-linux/platforms" is not a directory"

  - by Sam

  I start setting up the jenkins-maven-android and i'm facing an issue when running the jenkin job. My Machine Details $uname -a Linux development2 3.0.0-12-virtual #20-Ubuntu SMP Fri Oct 7 18:19:02 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux Steps to install the Android SDK in Ubuntu https://help.ubuntu.com/community/AndroidSDK since i'm working on headless env (ssh to client machine) i used following command to install the platform tools android update sdk --no-ui download apache maven and install on http://maven.apache.org/download.html mvn -version output root@development2:/opt/android-sdk-linux/tools# mvn -version Apache Maven 3.0.4 (r1232337; 2012-01-17 08:44:56+0000) Maven home: /opt/apache-maven-3.0.4 Java version: 1.6.0_24, vendor: Sun Microsystems Inc. Java home: /usr/lib/jvm/java-6-openjdk/jre Default locale: en_US, platform encoding: UTF-8 OS name: "linux", version: "3.0.0-12-virtual", arch: "amd64", family: "unix" root@development2:/opt/android-sdk-linux/tools# ran the following two command as mention in below sudo apt-get update sudo apt-get install ia32-libs Problems with Eclipse and Android SDK http://developer.android.com/sdk/installing/index.html As error suggest i gave the path to android SDK in jenkins build config still im getting the error clean install -Dandroid.sdk.path=/opt/android-sdk-linux Can someone help me to resolve this. Thanks Error I'm Getting Waiting for Jenkins to finish collecting data mavenExecutionResult exceptions not empty message : Failed to execute goal com.jayway.maven.plugins.android.generation2:android-maven-plugin:3.1.1:generate-sources (default-generate-sources) on project base-template: Execution default-generate-sources of goal com.jayway.maven.plugins.android.generation2:android-maven-plugin:3.1.1:generate-sources failed: Path "/opt/android-sdk-linux/platforms" is not a directory. Please provide a proper Android SDK directory path as configuration parameter <sdk><path>...</path></sdk> in the plugin <configuration/>. As an alternative, you may add the parameter to commandline: -Dandroid.sdk.path=... or set environment variable ANDROID_HOME. cause : Execution default-generate-sources of goal com.jayway.maven.plugins.android.generation2:android-maven-plugin:3.1.1:generate-sources failed: Path "/opt/android-sdk-linux/platforms" is not a directory. Please provide a proper Android SDK directory path as configuration parameter <sdk><path>...</path></sdk> in the plugin <configuration/>. As an alternative, you may add the parameter to commandline: -Dandroid.sdk.path=... or set environment variable ANDROID_HOME. Stack trace : org.apache.maven.lifecycle.LifecycleExecutionException: Failed to execute goal com.jayway.maven.plugins.android.generation2:android-maven-plugin:3.1.1:generate-sources (default-generate-sources) on project base-template: Execution default-generate-sources of goal com.jayway.maven.plugins.android.generation2:android-maven-plugin:3.1.1:generate-sources failed: Path "/opt/android-sdk-linux/platforms" is not a directory. Please provide a proper Android SDK directory path as configuration parameter <sdk><path>...</path></sdk> in the plugin <configuration/>. As an alternative, you may add the parameter to commandline: -Dandroid.sdk.path=... or set environment variable ANDROID_HOME. at org.apache.maven.lifecycle.internal.MojoExecutor.execute(MojoExecutor.java:225) at org.apache.maven.lifecycle.internal.MojoExecutor.execute(MojoExecutor.java:153) at org.apache.maven.lifecycle.internal.MojoExecutor.execute(MojoExecutor.java:145) at org.apache.maven.lifecycle.internal.LifecycleModuleBuilder.buildProject(LifecycleModuleBuilder.java:84) at org.apache.maven.lifecycle.internal.LifecycleModuleBuilder.buildProject(LifecycleModuleBuilder.java:59) at org.apache.maven.lifecycle.internal.LifecycleStarter.singleThreadedBuild(LifecycleStarter.java:183) at org.apache.maven.lifecycle.internal.LifecycleStarter.execute(LifecycleStarter.java:161) at org.apache.maven.DefaultMaven.doExecute(DefaultMaven.java:320) at org.apache.maven.DefaultMaven.execute(DefaultMaven.java:156) at org.jvnet.hudson.maven3.launcher.Maven3Launcher.main(Maven3Launcher.java:79) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:616) at org.codehaus.plexus.classworlds.launcher.Launcher.launchStandard(Launcher.java:329) at org.codehaus.plexus.classworlds.launcher.Launcher.launch(Launcher.java:239) at org.jvnet.hudson.maven3.agent.Maven3Main.launch(Maven3Main.java:158) at hudson.maven.Maven3Builder.call(Maven3Builder.java:98) at hudson.maven.Maven3Builder.call(Maven3Builder.java:64) at hudson.remoting.UserRequest.perform(UserRequest.java:118) at hudson.remoting.UserRequest.perform(UserRequest.java:48) at hudson.remoting.Request$2.run(Request.java:326) at hudson.remoting.InterceptingExecutorService$1.call(InterceptingExecutorService.java:72) at java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:334) at java.util.concurrent.FutureTask.run(FutureTask.java:166) at java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1110) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:603) at java.lang.Thread.run(Thread.java:679) Caused by: org.apache.maven.plugin.PluginExecutionException: Execution default-generate-sources of goal com.jayway.maven.plugins.android.generation2:android-maven-plugin:3.1.1:generate-sources failed: Path "/opt/android-sdk-linux/platforms" is not a directory. Please provide a proper Android SDK directory path as configuration parameter <sdk><path>...</path></sdk> in the plugin <configuration/>. As an alternative, you may add the parameter to commandline: -Dandroid.sdk.path=... or set environment variable ANDROID_HOME. at org.apache.maven.plugin.DefaultBuildPluginManager.executeMojo(DefaultBuildPluginManager.java:110) at org.apache.maven.lifecycle.internal.MojoExecutor.execute(MojoExecutor.java:209) ... 27 more Caused by: com.jayway.maven.plugins.android.InvalidSdkException: Path "/opt/android-sdk-linux/platforms" is not a directory. Please provide a proper Android SDK directory path as configuration parameter <sdk><path>...</path></sdk> in the plugin <configuration/>. As an alternative, you may add the parameter to commandline: -Dandroid.sdk.path=... or set environment variable ANDROID_HOME. at com.jayway.maven.plugins.android.AndroidSdk.assertPathIsDirectory(AndroidSdk.java:125) at com.jayway.maven.plugins.android.AndroidSdk.getPlatformDirectories(AndroidSdk.java:285) at com.jayway.maven.plugins.android.AndroidSdk.findAvailablePlatforms(AndroidSdk.java:260) at com.jayway.maven.plugins.android.AndroidSdk.<init>(AndroidSdk.java:80) at com.jayway.maven.plugins.android.AbstractAndroidMojo.getAndroidSdk(AbstractAndroidMojo.java:844) at com.jayway.maven.plugins.android.phase01generatesources.GenerateSourcesMojo.generateR(GenerateSourcesMojo.java:329) at com.jayway.maven.plugins.android.phase01generatesources.GenerateSourcesMojo.execute(GenerateSourcesMojo.java:102) at org.apache.maven.plugin.DefaultBuildPluginManager.executeMojo(DefaultBuildPluginManager.java:101) ... 28 more channel stopped Finished: FAILURE* android home Echo root@development2:~# echo $ANDROID_HOME /opt/android-sdk-linux

  Read the article

• Using Unity – Part 3

  - by nmarun

  The previous blog was about registering and invoking different types dynamically. In this one I’d like to show how Unity manages/disposes the instances – say hello to Lifetime Managers. When a type gets registered, either through the config file or when RegisterType method is explicitly called, the default behavior is that the container uses a transient lifetime manager. In other words, the unity container creates a new instance of the type when Resolve or ResolveAll method is called. Whereas, when you register an existing object using the RegisterInstance method, the container uses a container controlled lifetime manager - a singleton pattern. It does this by storing the reference of the object and that means so as long as the container is ‘alive’, your registered instance does not go out of scope and will be disposed only after the container either goes out of scope or when the code explicitly disposes the container. Let’s see how we can use these and test if something is a singleton or a transient instance. Continuing on the same solution used in the previous blogs, I have made the following changes: First is to add typeAlias elements for TransientLifetimeManager type: 1: <typeAlias alias="transient" type="Microsoft.Practices.Unity.TransientLifetimeManager, Microsoft.Practices.Unity"/> You then need to tell what type(s) you want to be transient by nature: 1: <type type="IProduct" mapTo="Product2"> 2: <lifetime type="transient" /> 3: </type> 4: <!--<type type="IProduct" mapTo="Product2" />--> The lifetime element’s type attribute matches with the alias attribute of the typeAlias element. Now since ‘transient’ is the default behavior, you can have a concise version of the same as line 4 shows. Also note that I’ve changed the mapTo attribute from ‘Product’ to ‘Product2’. I’ve done this to help understand the transient nature of the instance of the type Product2. By making this change, you are basically saying when a type of IProduct needs to be resolved, Unity should create an instance of Product2 by default. 1: public string WriteProductDetails() 2: { 3: return string.Format("Name: {0}<br/>Category: {1}<br/>Mfg Date: {2}<br/>Hash Code: {3}", 4: Name, Category, MfgDate.ToString("MM/dd/yyyy hh:mm:ss tt"), GetHashCode()); 5: } Again, the above change is purely for the purpose of making the example more clear to understand. The display will show the full date and also displays the hash code of the current instance. The GetHashCode() method returns an integer when an instance gets created – a new integer for every instance. When you run the application, you’ll see something like the below: Now when you click on the ‘Get Product2 Instance’ button, you’ll see that the Mfg Date (which is set in the constructor) and the Hash Code are different from the one created on page load. This proves to us that a new instance is created every single time. To make this a singleton, we need to add a type alias for the ContainerControlledLifetimeManager class and then change the type attribute of the lifetime element to singleton. 1: <typeAlias alias="singleton" type="Microsoft.Practices.Unity.ContainerControlledLifetimeManager, Microsoft.Practices.Unity"/> 2: ... 3: <type type="IProduct" mapTo="Product2"> 4: <lifetime type="singleton" /> 5: </type> Running the application now gets me the following output: Click on the button below and you’ll see that the Mfg Date and the Hash code remain unchanged => the unity container is storing the reference the first time it is created and then returns the same instance every time the type needs to be resolved. Digging more deeper into this, Unity provides more than the two lifetime managers. ExternallyControlledLifetimeManager – maintains a weak reference to type mappings and instances. Unity returns the same instance as long as the some code is holding a strong reference to this instance. For this, you need: 1: <typeAlias alias="external" type="Microsoft.Practices.Unity.ExternallyControlledLifetimeManager, Microsoft.Practices.Unity"/> 2: ... 3: <type type="IProduct" mapTo="Product2"> 4: <lifetime type="external" /> 5: </type> PerThreadLifetimeManager – Unity returns a unique instance of an object for each thread – so this effectively is a singleton behavior on a  per-thread basis. 1: <typeAlias alias="perThread" type="Microsoft.Practices.Unity.PerThreadLifetimeManager, Microsoft.Practices.Unity"/> 2: ... 3: <type type="IProduct" mapTo="Product2"> 4: <lifetime type="perThread" /> 5: </type> One thing to note about this is that if you use RegisterInstance method to register an existing object, this instance will be returned for every thread, making this a purely singleton behavior. Needless to say, this type of lifetime management is useful in multi-threaded applications (duh!!). I hope this blog provided some basics on lifetime management of objects resolved in Unity and in the next blog, I’ll talk about Injection. Please see the code used here.

  Read the article

• Install the Ajax Control Toolkit from NuGet

  - by Stephen Walther

  The Ajax Control Toolkit is now available from NuGet. This makes it super easy to add the latest version of the Ajax Control Toolkit to any Web Forms application. If you haven’t used NuGet yet, then you are missing out on a great tool which you can use with Visual Studio to add new features to an application. You can use NuGet with both ASP.NET MVC and ASP.NET Web Forms applications. NuGet is compatible with both Websites and Web Applications and it works with both C# and VB.NET applications. For example, I habitually use NuGet to add the latest version of ELMAH, Entity Framework, jQuery, jQuery UI, and jQuery Templates to applications that I create. To download NuGet, visit the NuGet website at: http://NuGet.org Imagine, for example, that you want to take advantage of the Ajax Control Toolkit RoundedCorners extender to create cross-browser compatible rounded corners in a Web Forms application. Follow these steps. Right click on your project in the Solution Explorer window and select the option Add Library Package Reference. In the Add Library Package Reference dialog, select the Online tab and enter AjaxControlToolkit in the search box: Click the Install button and the latest version of the Ajax Control Toolkit will be installed. Installing the Ajax Control Toolkit makes several modifications to your application. First, a reference to the Ajax Control Toolkit is added to your application. In a Web Application Project, you can see the new reference in the References folder: Installing the Ajax Control Toolkit NuGet package also updates your Web.config file. The tag prefix ajaxToolkit is registered so that you can easily use Ajax Control Toolkit controls within any page without adding a @Register directive to the page. <configuration> <system.web> <compilation debug="true" targetFramework="4.0" /> <pages> <controls> <add tagPrefix="ajaxToolkit" assembly="AjaxControlToolkit" namespace="AjaxControlToolkit" /> </controls> </pages> </system.web> </configuration> You should do a rebuild of your application by selecting the Visual Studio menu option Build, Rebuild Solution so that Visual Studio picks up on the new controls (You won’t get Intellisense for the Ajax Control Toolkit controls until you do a build). After you add the Ajax Control Toolkit to your application, you can start using any of the 40 Ajax Control Toolkit controls in your application (see http://www.asp.net/ajax/ajaxcontroltoolkit/samples/ for a reference for the controls). <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="WebForm1.aspx.cs" Inherits="WebApplication1.WebForm1" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server"> <title>Rounded Corners</title> <style type="text/css"> #pnl1 { background-color: gray; width: 200px; color:White; font: 14pt Verdana; } #pnl1_contents { padding: 10px; } </style> </head> <body> <form id="form1" runat="server"> <div> <asp:Panel ID="pnl1" runat="server"> <div id="pnl1_contents"> I have rounded corners! </div> </asp:Panel> <ajaxToolkit:ToolkitScriptManager ID="sm1" runat="server" /> <ajaxToolkit:RoundedCornersExtender TargetControlID="pnl1" runat="server" /> </div> </form> </body> </html> The page contains the following three controls: Panel – The Panel control named pnl1 contains the content which appears with rounded corners. ToolkitScriptManager – Every page which uses the Ajax Control Toolkit must contain a single ToolkitScriptManager. The ToolkitScriptManager loads all of the JavaScript files used by the Ajax Control Toolkit. RoundedCornersExtender – This Ajax Control Toolkit extender targets the Panel control. It makes the Panel control appear with rounded corners. You can control the “roundiness” of the corners by modifying the Radius property. Notice that you get Intellisense when typing the Ajax Control Toolkit tags. As soon as you type <ajaxToolkit, all of the available Ajax Control Toolkit controls appear: When you open the page in a browser, then the contents of the Panel appears with rounded corners. The advantage of using the RoundedCorners extender is that it is cross-browser compatible. It works great with Internet Explorer, Opera, Firefox, Chrome, and Safari even though different browsers implement rounded corners in different ways. The RoundedCorners extender even works with an ancient browser such as Internet Explorer 6. Getting the Latest Version of the Ajax Control Toolkit The Ajax Control Toolkit continues to evolve at a rapid pace. We are hard at work at fixing bugs and adding new features to the project. We plan to have a new release of the Ajax Control Toolkit each month. The easiest way to get the latest version of the Ajax Control Toolkit is to use NuGet. You can open the NuGet Add Library Package Reference dialog at any time to update the Ajax Control Toolkit to the latest version.

  Read the article

• Building a database installer with WiX, datadude and Visual Studio 2010

  - by jamiet

  Today I have been using Windows Installer XML (WiX) to build an installer (.msi file) that would install a SQL Server database on a server of my choosing; the source code for that database lives in datadude (a tool which you may know by one of quite a few other names). The basis for this work was a most excellent blog post by Duke Kamstra entitled Implementing a WIX installer that calls the GDR version of VSDBCMD.EXE which coves the delicate intricacies of doing this – particularly how to call Vsdbcmd.exe in a CustomAction. Unfortunately there are a couple of things wrong with Duke’s post: Searching for “datadude wix” didn’t turn it up in the first page of search results and hence it took me a long time to find it. And I knew that it existed. If someone else were after a post on using WiX with datadude its likely that they would never have come across Duke’s post and that would be a great shame because its the definitive post on the matter. It was written in October 2009 and had not been updated for Visual Studio 2010. Well, this blog post is an attempt to solve those problems. Hopefully I’ve solved the first one just by following a few of my blogging SEO tips while writing this blog post, in the rest of it I will explain how I took Duke’s code and updated it to work in Visual Studio 2010. If you need to build a database installer using WiX, datadude and Visual Studio 2010 then you still need to follow Duke’s blog post so go and do that now. Below are the amendments that I made that enabled the project to get built in Visual Studio 2010: In VS2010 datadude’s output files have changed from being called Database.<suffix> to <ProjectName>_Database.<suffix>. Duke’s code was referencing the old file name formats. Duke used $(var.SolutionDir) and relative paths to point to datadude artefacts I have replaced these with Votive Project References http://wix.sourceforge.net/manual-wix3/votive_project_references.htm I commented out all references to MicrosoftSqlTypesDbschema in DatabaseArtifacts.wxi. I don't think this is produced in VS2010 (I may be wrong about that but it wasn't in the output from my project) Similarly I commented out component MicrosoftSqlTypesDbschema in VsdbcmdArtifacts.wxi. It wasn't where Duke's code said it should have been so am assuming/hoping it isn't needed. Duke's ?define block to work out appropriate SrcArchPath actually wasn't working for me (i.e. <?if $(var.Platform)=x64 ?> was evaluating to false)  so I just took out the conditional stuff and declared the path explicitly to the “Program Files (x86)” path. The old code is still there though if you need to put it back. None of the <RegistrySearch> stuff is needed for VS2010 - so I commented it all out! Changed to use /manifest option rather than /model option on vsdbcmd.exe command-line. Personal preference is all! Added a new component in order to bundle along the vsdbcmd.exe.config file Made the install of the Custom Action dependent on the relevant feature being selected for install. This one is actually really important – deselecting the database feature for installation does not, by default, stop the CustomAction from executing and so would cause an error - so that scenario needs to be catered for I have made my amended solution available for download at: http://cid-550f681dad532637.office.live.com/self.aspx/Public/BlogShare/20110210/InstallMyDatabase.zip It contains two projects: the WiX project and the datadude project that is the source to be deployed (for demo purposes it only contains one table). I have also made the .msi available although in order that it gets through file blockers I changed the name from InstallMyDatabase.msi to InstallMyDatabase.ms_ – simply rename the file back once you have downloaded it from: http://cid-550f681dad532637.office.live.com/self.aspx/Public/BlogShare/20110210/InstallMyDatabase.ms%5E_ .You can try it out for yourself – the only thing it does is dump the files into %Program Files%\MyDatabase and uses them to install a database onto a server of your choosing with a name of your choosing - no damaging side-affects. I will caveat this by saying “it works on my machine” and, not having access to a plethora of different machines, I haven’t tested it anywhere else. One potential issue that I know of is that Vsdbcmd.exe has a dependency on SQL Server CE although if you have SQL Server tools or Visual Studio installed you should be fine. Unfortunately its not possible to bundle along the SQL Server CE installer in the .msi because Windows will not allow you to call one installer from inside another – the recommended way to get around this problem is to build a bootstrapper to bundle the whole lot together but doing that is outside the scope of this blog post. If you discover any other issues then please let me know. Here are the screenshots from the installer: And once installed…. Hope this is useful! @jamiet 

  Read the article

• Convert Excel File 'xls' to CSV, CAUTION: Bumps Ahead

  - by faizanahmad

  The task was to provide users with an interface where they can upload the 'csv' files, these files were to be processed and loaded to Database by a Console application. The code in Console application could not handle the 'xls' files so we thought, OK, lets convert 'xls' to 'csv' in the code, Seemed like fun. The idea was to convert it right after uploading within 'csv' file. As Microsoft does not recommend using the  Excel objects in ASP.NET, we decided to use the Jet engine to open xls. (Ace driver is used for xlsx) The code was pretty straight, can be found on following links: http://www.c-sharpcorner.com/uploadfile/yuanwang200409/102242008174401pm/1.aspx http://www.devasp.net/net/articles/display/141.html FIRST BUMP 'OleDbException (0x80004005): Unspecified error' ( Impersonation ): The ablove code ran fine in my test web site and test console application, but it gave an 'OleDbException (0x80004005): Unspecified error' in main web site, turns out imperonation was set to True and as soon as I changed it to False, it did work. on My XP box, web site was running under user                   'ASPNET'  with imperosnation set to FALSE                   'IUSR_*' i.e IIS guest user with impersonation set to TRUE The weired part was that both users had same rights on the folders I was saving files to and on Excel app in DCOM Config.  We decided to give it a try on Windows Server 2003 with web site set to windows authentication ( impersonation = true ) and yes it did work. SECOND BUMP 'External table not in correct format': I got this error with some files and it appeared that the file from client has some metadata issues  ( when I opened the file in Excel and try to save it ,excel  would give me this error saying File can not be saved in current format ) and the error was caused by that. Some people were able to reslove the error by using "Extended Properties=HTML Import;" in connection string. But it did not work for me. We decided to detour from here and use Excel object :( as we had no control on client setting the meta deta of Excel files. Before third bump there were a ouple of small thingies like 'Retrieving the COM class factory for component with CLSID {00024500-0000-0000-C000-000000000046} failed due to the following error: 80070005' Fix can be found at http://blog.crowe.co.nz/archive/2006/03/02/589.aspx THIRD BUMP ( Could not get rid of the EXCEL process  ):  I has all the code in place to 'Quiet' the excel, but, it just did not work. work around was done to Kill the process as we knew no other application on server was using EXCEL.  The normal steps to quite the excel application worked just fine in console application though.   FOURTH BUMP: Code worked with one file 1 on my machine and with the other file 2 code will break. and the same code will work perfectly fine with file 2 on some other machine . We moved it to QA  ( Windows Server 2003 )and worked with every file just perfect. But , then there was another problem: one user can upload it and second cant, permissions on folder and DCOM Conifg checked. Another Detour: Uplooad the xls as it is and convert in Console application.   Lesson Learnt:  If its 'xlsx' use 'ACE Driver' or read xml within excel as recommneded by MS. If xls and you know its always going to be properly formatted  'jet Engine'  Code: Imports Microsoft.Office.Interop Private Function ConvertFile(ByVal SourceFolder As String, ByVal FileName As String, ByVal FileExtension As String)As Boolean     Dim appExcel As New Excel.Application     Dim workBooks As Excel.Workbooks = appExcel.Workbooks     Dim objWorkbook As Excel.Workbook      Try                   objWorkbook = workBooks.Open(CompleteFilePath )                            objWorkbook.SaveAs(Filename:=CObj(SourceFolder & FileName & ".csv"), FileFormat:=Excel.XlFileFormat.xlCSV)       Catch ex As Exception         GenerateAlert(ex.Message().Replace("'", "") & " Error Converting File to CSV.")         LogError(ex )         Return False      Finally                      If Not(objWorkbook is Nothing) then               objWorkbook.Close(SaveChanges:=CObj(False))           End If           ReleaseObj(objWorkbook)                                      ReleaseObj(workBooks)           appExcel.Quit()           ReleaseObj(appExcel)                                 Dim proc As System.Diagnostics.Process           For Each proc In System.Diagnostics.Process.GetProcessesByName("EXCEL")               proc.Kill()           Next         DeleteSourceFile(SourceFolder & FileName & FileExtension)     End Try  Return True  End Function   Private Sub ReleaseObj(ByVal o As Object)     Try      System.Runtime.InteropServices.Marshal.ReleaseComObject(o)   Catch ex As Exception           LogError(ex )   Finally      o = Nothing    End Try End Sub     Protected Sub DeleteSourceFile(Byval CompleteFilePath As string)         Try             Dim MyFile As FileInfo = New FileInfo(CompleteFilePath)             If  MyFile.Exists Then                 File.Delete(CompleteFilePath)             Else              Throw New FileNotFoundException()             End If         Catch ex As Exception             GenerateAlert( " Source File could not be deleted.")              LogError(ex)         End Try     End Sub  The code to kill the process ( Avoid it if you can ): Dim proc As System.Diagnostics.Process For Each proc In System.Diagnostics.Process.GetProcessesByName("EXCEL")     proc.Kill() Next

  Read the article

• Using Oracle ADF Data Visualization Tools (DVT) Line Graphs to Display Weather Information

  - by Christian David Straub

  OverviewA guest post by Jeanne Waldman.I have a simple JDeveloper Fusion application that retrieves weather data. I wanted to compare the week's temperatures of different locations in a graph. I decided to check out the dvt:lineGraph component, and it took me a few minutes to add it to my jspx page and supply it with data.Drag and Drop the dvt:lineGraph onto your pageI opened my .jspx page in design modeIn the Component Palette, I selected ADF Data Visualization.Then I dragged 'Line' onto my page.A dialog popped up giving me options of the type of line graph. I chose the default.A lineGraph displayed with some default data. Hook up your weather dataNow I wanted to hook up my own data. I browsed the tagdoc, and I found the tabularData attribute.Attribute: tabularDataType: java.util.ListTagDoc:Specifies a list of data that the graph uses to create a grid and populate itself. The List consists of a three-member Object array for each data value to be passed to the graph. The members of each array must be organized as follows: The first member (index 0) is the column label, in the grid, of the data value. This is generally a String. If the graph has a time axis, then this should be a Java Date. Column labels typically identify groups in the graph. The second member (index 1) is the row label, in the grid, of the data value. This is generally a String. Row labels appear as series labels in the graph (usually in the legend). The third member (index 2) is the data value, which is usually a Double.The first member is the column label of the data value. This would be the day of the week.The second member is the row label of the data value. This would be the location name.The third member is the data value, usually a Double. This would be the temperature. I already had all this information, I just needed to put it in a List with a three-member Object array for each data value.   /**    * This is used for the lineGraph to show the data for each location.    */   public List<Object[]> getTabularData()   {      List<Object[]> tabularData = new ArrayList<Object []>();      List<WeatherForecast> weatherForecastList = getWeatherForecastList();      // loop through the list and build up the tabular data. Then cache it.      for(WeatherForecast wf : weatherForecastList)      {        List<ForecastDay> forecastDayList = wf.getForecastDayList();        String location = wf.getLocation();        for (ForecastDay fday : forecastDayList)        {          String day = fday.getPrettyDate();          String highTemp = fday.getHighF();          tabularData.add(new Object[]{day, location, Double.valueOf(highTemp)});        }             }      return tabularData;    }  Now I bound the lineGraph to this method by setting tabularData to#{weatherForAllLocationsBean.tabularData}weatherForAllLocationsBean is my bean that is defined in faces-config.xml. Adding a barGraphIn about 30 seconds, I added a barGraph with the same data. I dragged and dropped a bar graph onto the page, used the same tabularData as I did in the line graph. The page looks like this:  ConclusionI was very happy how fast it was to hook up my weather data to these graphs. They look great, and they have built in functionality. For instance, I can hide/show a location by clicking on the name of the location in the legend.

  Read the article

• CodePlex Daily Summary for Sunday, March 07, 2010

  CodePlex Daily Summary for Sunday, March 07, 2010New ProjectsAlgorithminator: Universal .NET algorithm visualizer, which helps you to illustrate any algorithm, written in any .NET language. Still in development.ALToolkit: Contains a set of handy .NET components/classes. Currently it contains: * A Numeric Text Box (an Extended NumericUpDown) * A Splash Screen base fo...Automaton Home: Automaton is a home automation software built with a n-Tier, MVVM pattern utilzing WCF, EF, WPF, Silverlight and XBAP.Developer Controls: Developer Controls contains various controls to help build applications that can script/write code.Dynamic Reference Manager: Dynamic Reference Manager is a set (more like a small group) of classes and attributes written in C# that allows any .NET program to reference othe...indiologic: Utilities of an IndioNeural Cryptography in F#: This project is my magistracy resulting work. It is intended to be an example of using neural networks in cryptography. Hashing functions are chose...Particle Filter Visualization: Particle Filter Visualization Program for the Intel Science and Engineering FairPólya: Efficient, immutable, polymorphic collections. .Net lacks them, we provide them*. * By we, we mean I; and by efficient, I mean hopefully so.project euler solutions from mhinze: mhinze project euler solutionsSilverlight 4 and WCF multi layer: Silverlight 4 and WCF multi layersqwarea: Project for a browser-based, minimalistic, massively multiplayer strategy game. Part of the "Génie logiciel et Cloud Computing" course of the ENS (...SuperSocket: SuperSocket, a socket application framework can build FTP/SMTP/POP server easilyToast (for ASP.NET MVC): Dynamic, developer & designer friendly content injection, compression and optimization for ASP.NET MVCNew ReleasesALToolkit: ALToolkit 1.0: Binary release of the libraries containing: NumericTextBox SplashScreen Based on the VB.NET code, but that doesn't really matter.Blacklist of Providers: 1.0-Milestone 1: Blacklist of Providers.Milestone 1In this development release implemented - Main interface (Work Item #5453) - Database (Work Item #5523)C# Linear Hash Table: Linear Hash Table b2: Now includes a default constructor, and will throw an exception if capacity is not set to a power of 2 or loadToMaintain is below 1.Composure: CassiniDev-Trunk-40745-VS2010.rc1.NET4: A simple port of the CassiniDev portable web server project for Visual Studio 2010 RC1 built against .NET 4.0. The WCF tests currently fail unless...Developer Controls: DevControls: These are the version 1.0 releases of these controls. Download the individually or all together (in a .zip file). More releases coming soon!Dynamic Reference Manager: DRM Alpha1: This is the first release. I'm calling it Alpha because I intend implementing other functions, but I do not intend changing the way current functio...ESB Toolkit Extensions: Tellago SOA ESB Extenstions v0.3: Windows Installer file that installs Library on a BizTalk ESB 2.0 system. This Install automatically configures the esb.config to use the new compo...GKO Libraries: GKO Libraries 0.1 Alpha: 0.1 AlphaHome Access Plus+: v3.0.3.0: Version 3.0.3.0 Release Change Log: Added Announcement Box Removed script files that aren't needed Fixed & issue in directory path Stylesheet...Icarus Scene Engine: Icarus Scene Engine 1.10.306.840: Icarus Professional, Icarus Player, the supporting software for Icarus Scene Engine, with some included samples, and the start of a tutorial (with ...mavjuz WndLpt: wndlpt-0.2.5: New: Response to 5 LPT inputs "test i 1" New: Reaction to 12 LPT outputs "test q 8" New: Reaction to all LPT pins "test pin 15" New: Syntax: ...Neural Cryptography in F#: Neural Cryptography 0.0.1: The most simple version of this project. It has a neural network that works just like logical AND and a possibility to recreate neural network from...Password Provider: 1.0.3: This release fixes a bug which caused the program to crash when double clicking on a generic item.RoTwee: RoTwee 6.2.0.0: New feature is as next. 16649 Add hashtag for tweet of tune.Now you can tweet your playing tune with hashtag.Visual Studio DSite: Picture Viewer (Visual C++ 2008): This example source code allows you to view any picture you want in the click of a button. All you got to do is click the button and browser via th...WatchersNET CKEditor™ Provider for DotNetNuke: CKEditor Provider 1.8.00: Whats New File Browser: Folders & Files View reworked File Browser: Folders & Files View reworked File Browser: Folders are displayed as TreeVi...WSDLGenerator: WSDLGenerator 0.0.0.4: - replaced CommonLibrary.dll by CommandLineParser.dll - added better support for custom complex typesMost Popular ProjectsMetaSharpSilverlight ToolkitASP.NET Ajax LibraryAll-In-One Code FrameworkWindows 7 USB/DVD Download Toolニコ生アラートWindows Double ExplorerVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2Caliburn: An Application Framework for WPF and SilverlightArkSwitchMost Active ProjectsUmbraco CMSRawrSDS: Scientific DataSet library and toolsBlogEngine.NETjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryIonics Isapi Rewrite FilterFarseer Physics EngineFasterflect - A Fast and Simple Reflection APIFluent Assertions

  Read the article

• Getting the innermost .NET Exception

  - by Rick Strahl

  Here's a trivial but quite useful function that I frequently need in dynamic execution of code: Finding the innermost exception when an exception occurs, because for many operations (for example Reflection invocations or Web Service calls) the top level errors returned can be rather generic. A good example - common with errors in Reflection making a method invocation - is this generic error: Exception has been thrown by the target of an invocation In the debugger it looks like this: In this case this is an AJAX callback, which dynamically executes a method (ExecuteMethod code) which in turn calls into an Amazon Web Service using the old Amazon WSE101 Web service extensions for .NET. An error occurs in the Web Service call and the innermost exception holds the useful error information which in this case points at an invalid web.config key value related to the System.Net connection APIs. The "Exception has been thrown by the target of an invocation" error is the Reflection APIs generic error message that gets fired when you execute a method dynamically and that method fails internally. The messages basically says: "Your code blew up in my face when I tried to run it!". Which of course is not very useful to tell you what actually happened. If you drill down the InnerExceptions eventually you'll get a more detailed exception that points at the original error and code that caused the exception. In the code above the actually useful exception is two innerExceptions down. In most (but not all) cases when inner exceptions are returned, it's the innermost exception that has the information that is really useful. It's of course a fairly trivial task to do this in code, but I do it so frequently that I use a small helper method for this: /// <summary> /// Returns the innermost Exception for an object /// </summary> /// <param name="ex"></param> /// <returns></returns> public static Exception GetInnerMostException(Exception ex) { Exception currentEx = ex; while (currentEx.InnerException != null) { currentEx = currentEx.InnerException; } return currentEx; } This code just loops through all the inner exceptions (if any) and assigns them to a temporary variable until there are no more inner exceptions. The end result is that you get the innermost exception returned from the original exception. It's easy to use this code then in a try/catch handler like this (from the example above) to retrieve the more important innermost exception: object result = null; string stringResult = null; try { if (parameterList != null) // use the supplied parameter list result = helper.ExecuteMethod(methodToCall,target, parameterList.ToArray(), CallbackMethodParameterType.Json,ref attr); else // grab the info out of QueryString Values or POST buffer during parameter parsing // for optimization result = helper.ExecuteMethod(methodToCall, target, null, CallbackMethodParameterType.Json, ref attr); } catch (Exception ex) { Exception activeException = DebugUtils.GetInnerMostException(ex); WriteErrorResponse(activeException.Message, ( HttpContext.Current.IsDebuggingEnabled ? ex.StackTrace : null ) ); return; } Another function that is useful to me from time to time is one that returns all inner exceptions and the original exception as an array: /// <summary> /// Returns an array of the entire exception list in reverse order /// (innermost to outermost exception) /// </summary> /// <param name="ex">The original exception to work off</param> /// <returns>Array of Exceptions from innermost to outermost</returns> public static Exception[] GetInnerExceptions(Exception ex) {     List<Exception> exceptions = new List<Exception>();     exceptions.Add(ex);       Exception currentEx = ex;     while (currentEx.InnerException != null)     {         exceptions.Add(ex);     }       // Reverse the order to the innermost is first     exceptions.Reverse();       return exceptions.ToArray(); } This function loops through all the InnerExceptions and returns them and then reverses the order of the array returning the innermost exception first. This can be useful in certain error scenarios where exceptions stack and you need to display information from more than one of the exceptions in order to create a useful error message. This is rare but certain database exceptions bury their exception info in mutliple inner exceptions and it's easier to parse through them in an array then to manually walk the exception stack. It's also useful if you need to log errors and want to see the all of the error detail from all exceptions. None of this is rocket science, but it's useful to have some helpers that make retrieval of the critical exception info trivial. Resources DebugUtils.cs utility class in the West Wind Web Toolkit© Rick Strahl, West Wind Technologies, 2005-2011Posted in CSharp  .NET  

  Read the article

• Azure &ndash; Part 6 &ndash; Blob Storage Service

  - by Shaun

  When migrate your application onto the Azure one of the biggest concern would be the external files. In the original way we understood and ensure which machine and folder our application (website or web service) is located in. So that we can use the MapPath or some other methods to read and write the external files for example the images, text files or the xml files, etc. But things have been changed when we deploy them on Azure. Azure is not a server, or a single machine, it’s a set of virtual server machine running under the Azure OS. And even worse, your application might be moved between thses machines. So it’s impossible to read or write the external files on Azure. In order to resolve this issue the Windows Azure provides another storage serviec – Blob, for us. Different to the table service, the blob serivce is to be used to store text and binary data rather than the structured data. It provides two types of blobs: Block Blobs and Page Blobs. Block Blobs are optimized for streaming. They are comprised of blocks, each of which is identified by a block ID and each block can be a maximum of 4 MB in size. Page Blobs are are optimized for random read/write operations and provide the ability to write to a range of bytes in a blob. They are a collection of pages. The maximum size for a page blob is 1 TB.   In the managed library the Azure SDK allows us to communicate with the blobs through these classes CloudBlobClient, CloudBlobContainer, CloudBlockBlob and the CloudPageBlob. Similar with the table service managed library, the CloudBlobClient allows us to reach the blob service by passing our storage account information and also responsible for creating the blob container is not exist. Then from the CloudBlobContainer we can save or load the block blobs and page blobs into the CloudBlockBlob and the CloudPageBlob classes.   Let’s improve our exmaple in the previous posts – add a service method allows the user to upload the logo image. In the server side I created a method name UploadLogo with 2 parameters: email and image. Then I created the storage account from the config file. I also add the validation to ensure that the email passed in is valid. 1: var storageAccount = CloudStorageAccount.FromConfigurationSetting("DataConnectionString"); 2: var accountContext = new DynamicDataContext<Account>(storageAccount); 3:  4: // validation 5: var accountNumber = accountContext.Load() 6: .Where(a => a.Email == email) 7: .ToList() 8: .Count; 9: if (accountNumber <= 0) 10: { 11: throw new ApplicationException(string.Format("Cannot find the account with the email {0}.", email)); 12: } Then there are three steps for saving the image into the blob service. First alike the table service I created the container with a unique name and create it if it’s not exist. 1: // create the blob container for account logos if not exist 2: CloudBlobClient blobStorage = storageAccount.CreateCloudBlobClient(); 3: CloudBlobContainer container = blobStorage.GetContainerReference("account-logo"); 4: container.CreateIfNotExist(); Then, since in this example I will just send the blob access URL back to the client so I need to open the read permission on that container. 1: // configure blob container for public access 2: BlobContainerPermissions permissions = container.GetPermissions(); 3: permissions.PublicAccess = BlobContainerPublicAccessType.Container; 4: container.SetPermissions(permissions); And at the end I combine the blob resource name from the input file name and Guid, and then save it to the block blob by using the UploadByteArray method. Finally I returned the URL of this blob back to the client side. 1: // save the blob into the blob service 2: string uniqueBlobName = string.Format("{0}_{1}.jpg", email, Guid.NewGuid().ToString()); 3: CloudBlockBlob blob = container.GetBlockBlobReference(uniqueBlobName); 4: blob.UploadByteArray(image); 5:  6: return blob.Uri.ToString(); Let’s update a bit on the client side application and see the result. Here I just use my simple console application to let the user input the email and the file name of the image. If it’s OK it will show the URL of the blob on the server side so that we can see it through the web browser. Then we can see the logo I’ve just uploaded through the URL here. You may notice that the blob URL was based on the container name and the blob unique name. In the document of the Azure SDK there’s a page for the rule of naming them, but I think the simple rule would be – they must be valid as an URL address. So that you cannot name the container with dot or slash as it will break the ADO.Data Service routing rule. For exmaple if you named the blob container as Account.Logo then it will throw an exception says 400 Bad Request.   Summary In this short entity I covered the simple usage of the blob service to save the images onto Azure. Since the Azure platform does not support the file system we have to migrate our code for reading/writing files to the blob service before deploy it to Azure. In order to reducing this effort Microsoft provided a new approch named Drive, which allows us read and write the NTFS files just likes what we did before. It’s built up on the blob serivce but more properly for files accessing. I will discuss more about it in the next post.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

< Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >