Search Results

Search found 12666 results on 507 pages for 'knowledge base'.

Page 397/507 | < Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >

• Video memory buswidth vs video memory Bandwidth

  - by Mixxiphoid

  My current video card (9600GT) is dying and I'm searching for a new video card. Between acquiring my current one and now, I got a lot more knowledge about hardware and I want to use that to pick my new card. So I decided to not just buy some popular card blindly, but to search for a card able to handle my hardware requirements. I searched the specs at the NVidia site for the GT640 and was confused by the memory section and some questions raised. My current card's memory bus width is 256bit and has 1GB of memory. I checked Google about the importance of bus width. And all the links basically said the same 'The higher the number the more potential simultaneously traffic can be transferred'. This was already clear to me, yet there are currently a lot of new cards which are considered better than my current one with a lower bus width. To go in more detail about my question I copied the memory info from the NVidia site: GT 640 GT640 GDDR5 Memory Specs: Memory Clock 1.8 Gbps 5.0 Gbps Standard Memory Config 2048 MB 1024 MB Memory Interface DDR3 GDDR5 Memory Interface Width 128-bit 64-bit Memory Bandwidth (GB/sec) 28.5 40.0 What puzzled me is that the Memory Bandwidth seems to me the most important part, yet the lower bus width has the higher 'performance'. Is this due to the fact the memory interface is GDDR5 and is therefore able to have a higher memory clock speed (5Gbps)? If I am to buy a new video card, should I check the bus width? Memory clock? Bandwith? Amount of memory? My current card ahs 1GB memory, so I was searching for a 2GB memory card, but now I'm not so sure any more whether that is really 'better'. My main question: To me it seems that memory performance is made up by the combination of bus width and frequency. Is this true? If yes, why are there so many sites telling me I need to get a card with a high bus width? If no, then what IS important when it goes about memory performance on a video card. NOTE: The memory bandwidth is (almost) never displayed on vendor sites. How can I determine which card is better without knowing the bandwith?

  Read the article

• SMTP host name vs. domain in "From:" address vis-a-vis Email Deliverability

  - by Jared Duncan

  I'm trying to implement (or make sure that I'm correctly following) email sending best practices to improve deliverability, but the role of the smtp server's host name vs the domain name of the From: email address seems to be unclear, even after reading dozens of people's articles/input. Specifically, I understand that to satisfy the reverse DNS check, there must be a PTR record for the IP address of the sending machine that yields a domain name that matches the host name of the sending machine / SMTP server. Some say it needs to match the one given by the "hostname" command, most say it's the one provided with the HELO / EHLO statement, and this guy even says they MUST be the same (according to / enforced by what, I don't know; that's only a minor point of confusion, anyhow). First, what I can't find anywhere is whether or not the domain name of the From: email address needs to match the domain name of the SMTP server. So in my case, I have a VPS with linode. It primarily hosts a particular domain of mine, example.com, but I also sometimes do work on other projects: foo.com and bar.com. So what I'm wondering is if I can just leave the default linode PTR record (which resolves to abc.def.linode.com), make sure that abc.def.linode.com is what my mail server (qmail) is configured to say at HELO, and then proceed to use it to send out emails for example.com, foo.com, et al. If so, then I am confused by the advice given here, specifically (in a listing of bad case scenarios): No SPF record for the domain being used in the HELO command Why would THAT domain need an SPF record? And if it does, which domain should it provide whitelisting for: the HELO domain, or the domain of the From: email address (envelope sender)? Also, which domain would need to accept mail sent to [email protected]? If the domains must be the same, that would seem rather limiting to me, because then for every domain you wanted to send email from, you'd have to get another IP address for it. It would also compromise or ruin one's ability to do non-email sending things (e.g. wget) relatively anonymously. However, the upside--if this is the case--is that it would make for a far less confusing setup. I'm currently using the linode.com SMTP+PTR domain and example.com From: address combination without much of any deliverability issue, but my volume is very low and I'd like to know if someone out there has experience with larger volumes and has specifically tested the difference and/or has inside knowledge and/or has an authoritative answer (and source) for this particular question. I'm happy to clarify anything, let me know. Thanks in advance.

  Read the article

• Sent items listed by sender's name (my name!) not recipient in Outlook for Mac 2011

  - by user568458

  Outlook 2011 on a Mac (OSX7 Lion), on a (mostly PC) office network using Microsoft Exchange server. In Outlook 2011, in the network "Sent Items" folder, all emails are listed showing the sender's name (my name), not the recipients' names. That means every single email is headed with my own name, like this: My Name 08/09/2012 Some subject line [flag] My Name 08/09/2012 Re: Another subject line [flag] My Name 07/09/2012 Re: different subject line [flag] My Name 07/09/2012 different subject line [flag] ...and so on. There's no clue at all as to who these emails were to, until I open each and every one. I guess it's reassuring to be told that every email that I sent was sent by me... and if I was ever to forget my own name while browsing my sent emails folder, it'd be super useful... But it's not very helpful for navigating sent emails. Is this normal for Office for Mac 2011? How can I fix this, so that the list shows the recipients' names instead of endlessly reminding me of my own name? Things I've found while researching this: This can also happen in Outlook for Windows. On Windows, it's easily fixed by resetting the field. That method doesn't work on Mac because the fields can't be selected separately. It seems this can also happen in Apple Mail too, and a lot of people seem stumped by this. I can't find anything on this specific to Outlook 2011 or Outlook for Mac in general. A simple guide on how to fix this would be the best answer, but I'd also welcome any knowledgable thoughts from Microsoft Exchange Server people on whether this sounds like an Outlook settings issue which I can fix on my machine, or some issue relating to how the Mac gets data from the server and network. The fact that Apple Mail users have encountered the same issue with no apparent fix makes me think the problem might be in the network rather than the mail client - but that's way beyond my limited knowledge of these things. I don't know whether the local ("On my computer") Sent Items folder has the same problem, as it's configured so that no emails except drafts are ever stored in these local folders. Drafts saved locally are listed by recipient as expected.

  Read the article

• NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

  - by Corey Kennedy

  What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help! edit: 1/19/2011 Well, this is truly bizarre. To my knowledge I've made no changes to either system - the laptop or the server. But today after starting up the server for the first time in a few days, and making sure that nxserver was running, I was able to connect with the nxclient from my laptop with no problems. I have a full desktop in a single window and I am able to interact with it normally. This is really weird, but the problem seems to be resolved.

  Read the article

• adress-chunk: separate data stored in one collumn - into three (street, postal-code, town)

  - by zero

  hello dear community. Hello dear friends form all over the planet first of all - this is a great great forum. I like this place to share the ideas. It is so great to see such a supportive place - featuring the knowledge exchange! today i have the following thing to discuss: i want to separate the following data that are stored in one column of a calc-spreadsheet: See the following data: You see that there are the following categories:_ steet, postal-code, town All the data are stored in only one Colum; Well to be honest: i want to separate them into three colums steet, postal-code, town see the data: what can i do? note - you see that there are commas inbetween the enties: and besides this we see that we have a postal-code with four digits: that is a good thing. Perhaps we can use this as a marker that helps us to separate the data?! Perhaps See a data-sample! Here you can see some exceptions: eg. the town that has two words combinde with a "-" ... or somethims without any signs and characters... see the following... as an example: Max-Bader-Platz 1, 5620 Schwarzach im Pongau Pestalozzistraße 4, 9990 Nussdorf-Debant Schulstraße 4, 5162 Obertrum am See But i guess that this means no problem... What do you think about this? I am very very interested to get your opinion! i look forward to hear from you! regards see a snipped of the dataset - that is stored in one column -[b]Goal: [/b]i want to separate the datas into three collumns... : Schulweg 6, 9871 Seeboden Khevenhüllerstraße 45, 4861 Schörfling Franz Xaver Rennstr.18, 6460 Imst Schulstraße 4, 5162 Obertrum am See Schulweg 6, 7432 Oberschützen Pestalozzistraße 4, 9990 Nussdorf-Debant Niederndorf bei Kufstein 53c, 6342 Niederndorf bei Kufstein Hauptschulstraße 18, 2183 Neusiedl an der Zaya Seeweg 14, 5202 Neumarkt am Wallersee Europaplatz 1, 8820 Neumarkt in Steiermark Schulstraße 7, 4212 Neumarkt im Mühlkreis Schulstraße 20, 4720 Neumarkt im Hausruckkreis Bahnhofstr. 10, 4872 Neukirchen an der Vöckla Schulstraße 5b, 4780 Schärding Reitbergstraße 2, 4311 Schwertberg Europaplatz 1, 2320 Schwechat Am Schulberg 5, 3931 Schweiggers Waidach 8, 6130 Schwaz Waidach 8, 6130 Schwaz Max-Bader-Platz 1, 5620 Schwarzach im Pongau Markt 29, 2662 Schwarzau im Gebirge Hofsteigstraße 68, 6858 Schwarzach Gmundner Straße 7, 4690 Schwanenstadt Mühlfeldstraße 1, 4690 Schwanenstadt Mainsdorferstraße 18, 8541 Schwanberg Jakob Stemer-Weg 3, 6780 Schruns Obere Umfahrungsstraße 16, 2432 Schwadorf bei Wien Battloggstraße 54, 6780 Schruns Schloss-Straße 19, 5020 Salzburg Schillerplatz 2, 8280 Fürstenfeld Erzherzog-Johann-Str. 400, 8970 Schladming Schulgasse 261, 8811 Scheifling i look forward to hear from you!! regards

  Read the article

• Core i7 c1e and speedstepping - BSOD on shutdown

  - by DeaconDesperado

  I'm having an interesting problem with my recent Core i7 Digital Audio workstation build that I am curious to see if others have encountered. First, here are the specs on the machine. ASUS P6TD Deluxe Intel X58 Socket LGA1366 MB Intel Core i7-950 3.06Ghz 8M LGA1366 CPU CORSAIR DOMINATOR 6GB (3 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 Western Digital Caviar Black WD5001AALS 500GB Plus a couple ASUS optical drives and a 750W Corsair PSU. Running Windows 7 x64. All this is connected to the nefarious Digi 002 firewire audio interface for use with Pro Tools. I following mostly the specs posted by many other I7 users in the digidesign community who pooled their collective knowledge in this thread. Now after completing my build, I fell victim to the "UD5 squeal" described at that forum thread. So taking the advice posted, I disabled c1e advanced halt state and Intel speed stepping (I would likely have done this anyway to maintain a stable clock, power consumption isn't really a relevant concern on this machine.) I enabled XMP to set the ram timings properly as well. What I am experiencing is a BSOD upon shutdown, but only immediately after windows fully exits and ends all processes. The error is a MACHINE_CHECK_EXCEPTION 0x000000. The funny thing is that it is extremely intermitent and only occurs if the shutdown immediately followed a period of relative idleness. It does not a generate a minidump, I suspect because windows monitoring has terminated by the time this error occurs. No damage is evident and one can simply turn off manually and the system will act as though a proper shutdown had occurred. If anything it is a annoyance, I just want to be certain it is not affecting my long term stability. I have read that the i7 950 does not like DRAM voltages past 1.65, but that they are acceptable if they are within .5 of the BLCK setting. I have tried disabling XMP and setting all timings to auto and the problem still manifests in an identical way. It is suspect that the cpu idleness preceding shutdown is the determining factor, as both c1e and speedstepping are both settings intended to modify handling of this state. Any suggestions or prior experiences would be greatly appreciated. EDIT: The behavior very closely resembles what's described in this thread: http://www.tomshardware.com/forum/12003-63-shut-problem-windows The benign nature of it of is identical. I can't seem to download the hotfix cited there however.

  Read the article

• IE and Google Chrome timeout on an IIS6 hosted SSL page that Firefox handles well

  - by Thomas

  Ok, here's the scenario: Up until a few weeks ago, none of us noticed anything wrong with the corporate website. People were using it without complaint. Then, a client complained that a specific page on the site was timing out for him, and only when he committed a POST action on a form filled with data. I checked it out, and it timed out for me, too. But, it only timed out in Google Chrome and IE, not in Firefox. Additionally, the same page, on the same server, but served from a different domain name (one not under the protection of SSL, either) does not time out under any browser. To clarify: https://www.mysite.com/changes.php times out on POST, but the same with http works fine. That distinction (SSL vs. Non-SSL) seems to be important, as nothing else has changed. Our certificate is valid, and Firefox detects no errors thrown by the page. I've looked at the Request and Response headers from the page, and they all follow the correct formats. Then, after wandering through the site, I noticed a few other things. Both IE and Chrome will frequently time out on any page that is PHP-based. They never time out on static images or html files. I've looked at the site from a variety of different servers, my home and work workstations, and my netbook. Because of that, I've discounted a viral infection, as I highly doubt a virus is going to hit every one of the machines to which I have access in exactly the same manner. My setup is: Server: Win2k3, II6, PHP 5.2.9-1. Clients: IE7, IE8, Chrome (regular and dev channel): Frequent timeouts on PHP pages. Firefox 2, Firefox 3: No timeouts. Firebug shows no errors or even lengthy periods serving the pages. I've spent 2 days searching for any tech knowledge that I can find, and my search parameters are all too general. Everyone has problems loading SSL pages in IE and Chrome for a wide variety of reasons. The infrequent nature of the timeouts and the fact that there are no errors being reported anywhere is starting to drive me insane. Does anyone have any insight on a problem like this?

  Read the article

• PTR Record Troubles

  - by Physikal

  I am having a hell of a time getting our PTR record right. Our current PTR zone looks like this: $ttl 38400 @ IN SOA ns1.domain.com. admin.domain.com. ( 1268669139 10800 3600 604800 38400 ) xxx.xxx.xxx.in-addr.arpa. IN NS ns2.domain.com. xxx.xxx.xxx.in-addr.arpa. IN NS ns1.domain.com. 97 IN PTR mail.domain.com. xxx.xxx.xxx.xxx.in-addr.arpa. IN PTR mail.domain.com. 97.96/28. IN PTR mail.domain.com For some reason the only thing that works is the 97.96/28. When this line is in there it actually says I have a PTR record when reporting from intodns.com. If I remove that line, it says I have no PTR. I have followed instructions from http://www.philchen.com/2007/04/04/configuring-reverse-dns and when I follow those instructions intodns.com says I have no PTR. When it does work with the line 97.96/28., the PTR kicks back as (from intodns.com) : 97.xxx.xxx.xxx.in-addr.arpa -> mail.domain.com.xxx.xxx.xxx.in-addr.arpa Which is, to my knowledge, an incorrect PTR. I want it to just kick back as mail.domain.com, without the xxx.xxx.xxx.in-addr.arpa extension. I have tried everything I can think of but I can't fix it. I can't help but think it's one of those things that is so stupid and simple I'm going to do the ol'facepalm. Any help is greatly appreciated. Thanks! In the event that the domain zone is needed, here it is: $ttl 38400 @ IN SOA domain.com. [email protected]. ( 1265221037 10800 3600 604800 38400 ) domain.com. IN A xxx.xxx.xxx.xxx www.domain.com. IN A xxx.xxx.xxx.xxx ftp.domain.com. IN A xxx.xxx.xxx.xxx m.domain.com. IN A xxx.xxx.xxx.xxx localhost.domain.com. IN A 127.0.0.1 webmail.domain.com. IN A xxx.xxx.xxx.xxx admin.domain.com. IN A xxx.xxx.xxx.xxx mail.domain.com. IN A xxx.xxx.xxx.xxx domain.com. IN MX 5 mail.domain.com. domain.com. IN TXT "v=spf1 a mx a:domain.com ip4:xxx.xxx.xxx.xxx ?all" domain.com. IN NS ns1 domain.com. IN NS ns2 ns1 IN A xxx.xxx.xxx.xxx ns2 IN A xxx.xxx.xxx.xxx Any double entries in different formats were part of my troubleshooting process.

  Read the article

• High load on X3220 Quad Core Linux Apache server

  - by John Templar

  I'm seriously in need of help. My sites are now nearly impossible to use because of massive loads on my server. I'm already a month late on my mortgage and this really isn't helping my situation. I've been working on fixing this intermittent load problem for months (never this bad). I'm suspecting some kind of attack since I'm under DDOS attack a lot! I've been trying to figure out what is causing the load but I'm afraid I just don't have the experience or knowledge to understand all the data I've been looking at. I don't even know where to begin or how to test for the large array of attacks out there. Here's some data you might find useful... Server: Xeon X3220 Quad Core 2.4 GHz - Linux, FreeBSD 500 GB HD and 8 Gig of Ram. Runs Centos release 5.7 Server Version: Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 mod_qos/9.74 Warning: All sites are softcore adult sites - mostly fantasy art like elves and amazons. 1) Sites may run fine for weeks or just days at less than 10 load then start jumping to 40-80 load - no idea why. Same sites, same mods, same amount of traffic - just WHAM! 2) I get an email almost every day that says: "Large Number of Failed Login Attempts from IP (different each time)". My webhost (who almost never helps me) told me it was a udp flood or something. 3) I've changed the port for MySQL from the default. If I ever put it back to the default - I get Loads of over 100 from what must be a constant mysql port flood. 4) I've reconfigured MYSQL. Link: http://www.deadlyamazons.com/logs/mycnf.txt 5) I have 3 Joomla Jomsocial networks. I've spent a couple weeks turning all the mods/plugins off, waiting a day and then turning them back on the next day or later if there isn't any change (there hasn't been). For example, on Thursday I'll turn off videos, on Friday I'll turn off chat.. etc and nothing changes the load appreciably. 6) Joomla info: All SEF turned off - sh404sef completely disabled and removed. Components: Joomla 1.5.22, Jomsocial 2.0.5, Kunena 1/31/2011, HWDMediashare 11/22/2010 and JBolo Chat 2.7.3, Comet Chat or Envolve Chat. Page Compression is on, Cache is on 15 mins. Please click on this forum to see links to all my reports: http://forum.joomla.org/viewtopic.php?f=433&t=706035&p=2777500#p2777500 Any help would be highly appreciated.

  Read the article

• BIND DNS server (Windows) - Unable to access my local domain from other computers on LAN

  - by Ricardo Saraiva

  I have a BIND DNS server running on my Windows 7 development machine and I'm serving pages with WAMPSERVER. My ideia is to develop some tools (in PHP) for my intranet at work and I want them to be accessible via LAN in this format: http://tools.mycompany.com I've already placed BIND and I can access http://tools.mycompany.com on the machine that holds BIND server, but I cannot access it from other LAN computers. I've done the following on my router: defined static IP's for all LAN computers set Port Forwarding to my server (remember: it serves DNS and Web pages) set DNS server configuration to point to my LAN server On LAN computers, I went to Local Area Network properties and also changed the DNS server IP in order to point to my local DNS server. If it helps, here is my named.conf file: options { directory "c:\windows\SysWOW64\dns\etc"; forwarders {127.0.0.1; 8.8.8.8; 8.8.4.4;}; pid-file "run\named.pid"; allow-transfer { none; }; recursion no; }; logging{ channel my_log{ file "log\named.log" versions 3 size 2m; severity info; print-time yes; print-severity yes; print-category yes; }; category default{ my_log; }; }; zone "mycompany.com" IN { type master; file "zones\db.mycompany.com.txt"; allow-transfer { none; }; }; key "rndc-key" { algorithm hmac-md5; secret "qfApxn0NxXiaacFHpI86Rg=="; }; controls { inet 127.0.0.1 port 953 allow { 127.0.0.1; } keys { "rndc-key"; }; }; ...and a single zone I've defined - file db.mycompany.com.txt: $TTL 6h @ IN SOA tools.mycompany.com. hostmaster.mycompany.com. ( 2014042601 10800 3600 604800 86400 ) @ NS tools.mycompany.com. tools IN A 192.168.1.4 www IN A 192.168.1.4 On the file above 192.168.1.4 is the IP of the local machine inside my LAN. Can someone help me here? I need my web pages to be accessible from other computers inside my LAN using my custom domain name. I've tried on other computers and they can access my server via http://192.168.1.4/, but no able when using http://tools.mycompany.com . Please, consider the following: I'm completely new to BIND I have basic knowledge in Apache configuration Thanks a lot for your help.

  Read the article

• How should I use LVM with Ganeti?

  - by javano

  I am building a small Ganeti cluster on some low end hardware (I only have the resources given sadly). I am confused as to the use of LVMs with DRBD. I have two instances and three nodes. What I want is instance1 replicated between node 1 & 2, and instance2 replicated between nodes 3 & 2 (so node2 is doing nothing, except waiting for either node1 or 3 to fail, is it is the secondary node for both instances). This is because node2 is a lower hardware spec than 1 and 3, so I just want it as an hot-spare. How can I achieve this? I don't want instance1 being replicated to node3 for example, nor instance2 replicated to node1. Nodes 1 & 2 have /dev/sda5 which is 150GBs (for example). Nodes 2 & 3 have /dev/sda6 which is also 75GBs (for example). Using just nodes 1 & 2, after looking at the Ganeti docs I would; vgcreate my-vg Next I would create the cluster via gnt-cluster VG = "my-vg". It is here I believe that I am missing some knowledge. I believe that what I need to do is create the same Logical Volume on nodes 1 & 2 in Volume Group "my-vg", that solely consists of /dev/sda5 and call it "lv1". Then create an Logical Volume on nodes 2 & 3 the solely consists of /dev/sda6 in "my-vg" that is called "lv2". When creating instance1 I would then use "-vg=lv1 -n node1:node2", and when creating instance2 I would use "-vg=lv2 -n node3:node2". I breifly had a go at this today and I'm dubious if this will be possible. When trying to create instance2, "lv2" wont exist on node1 (the cluster master) so I don't believe it will allow the instance creation. Could I create a 1kb parition (/dev/sda6) on node1 and put it into a LV called "lv2" or is that too flakey? Is this set up possible? Thank you.

  Read the article

• 2nd Year College - Learning - Microsoft Server Products

  - by Ryan

  As the title says, I just finished my first year of college (majoring in Software Engineering). Fortunately my school likes Microsoft enough, and I can get pretty much anything I want that Microsoft sells. I also can get IBM Websphere and the like for free as well. Earlier this year, I set up an oldish computer (2.6 Pentium D, x64) to run ubuntu server headless. I'm predominately a Java developer, so Apache, Maven, Nexus, Sonar, SVN, etc made it onto the machine. It worked really well for personal and school projects, especially team projects (quick ramp up). Anyways, I started to pick up C# to complement my Java knowledge (don't judge me :P), and am interested in working with some of the associated Microsoft equivalents. The machine currently has the Ubuntu install, as well as Windows 7 Ultimate. I do all of my actual development work off my laptop, also running Windows 7 Ultimate. I was wondering what software you would recommend putting on the machine. I’m not actually serving anything off the machine itself, but in Ubuntu I had it doing integration tests with Hudson on every commit, and profiling my applications, etc, etc. The machine would be running headless, and I would remote into it. Here is what I am currently leaning towards / wondering about: Windows 7 Ultimate vs Windows Server 2008 (R2) (no one is really clear why I should go with one over the other) Windows Team Foundation Sharepoint (Never used it before, kind of meh about it) IBM Websphere or Glassfish (Some Java EE web server) SQL Server 2008 A DVCS In order to better control product conflicts / limit resource use, I’m wondering if I should install things into virtual machines (I can get VmWare or Microsoft Virtualization Products) I also plan on installing everything I had running under Linux (it’s almost entirely Java based development software, so it’ll run on both, only reason I went with ubuntu during the year was because the apache build seemed better). I’m primarily looking to become familiar with enterprise software development tools, as well as get something functional that will help my development process. (IE, I’ll still use project and assign tasks even though I might be the only one to assign tasks to, just to practice doing so). Is there any other software / configuration details I should explore? Opinions on my current list? I primarily use C#, Java, and PHP. I'm familiar with ruby, and python as well. Thanks!

  Read the article

• New Exchange 2010 CAS cannot find domain controllers

  - by NorbyTheGeek

  I am experiencing problems migrating from Exchange 2003 to Exchange 2010. I am on the first step: installing a new 2010 Client Access Server role. The Active Directory domain functional level is 2003. All domain controllers are 2003 R2. The only existing Exchange 2003 server happens to be housed on one of the domain controllers. It is running Exchange 2003 Standard w/ SP2. IPv6 is enabled and working on all domain controllers, servers, and routers, including this new Exchange server. After installing the CAS role on a new 2008 R2 server (Hyper-V VM) I am receiving 2114 Events: Process MSEXCHANGEADTOPOLOGYSERVICE.EXE (PID=1600). Topology discovery failed, error 0x80040a02 (DSC_E_NO_SUITABLE_CDC). Look up the Lightweight Directory Access Protocol (LDAP) error code specified in the event description. To do this, use Microsoft Knowledge Base article 218185, "Microsoft LDAP Error Codes." Use the information in that article to learn more about the cause and resolution to this error. Use the Ping or PathPing command-line tools to test network connectivity to local domain controllers. Prior to each, I receive the following 2080 Event: Process MSEXCHANGEADTOPOLOGYSERVICE.EXE (PID=1600). Exchange Active Directory Provider has discovered the following servers with the following characteristics: (Server name | Roles | Enabled | Reachability | Synchronized | GC capable | PDC | SACL right | Critical Data | Netlogon | OS Version) In-site: b.company.intranet CDG 1 0 0 1 0 0 0 0 0 s.company.intranet CDG 1 0 0 1 0 0 0 0 0 Out-of-site: a.company.intranet CD- 1 0 0 0 0 0 0 0 0 o.company.intranet CD- 1 0 0 0 0 0 0 0 0 g.company.intranet CD- 1 0 0 0 0 0 0 0 0 Connectivity between the new Exchange server and all domain controllers via IPv4 and IPv6 are all working. I have verified that the new Exchange server is a member of the following groups: Exchange Servers Exchange Domain Servers Exchange Install Domain Servers Exchange Trusted Subsystem Heck, I even put the new Exchange server into Domain Admins just to see if it would help. It didn't. I can't find any evidence of Active Directory replication problems, all pre-setup Setup tasks (/PrepareLegacyExchangePermissions, /PrepareSchema, /PrepareAD, /PrepareDomain) completed successfully. The only problem so far that I haven't been able to resolve with my Active Directory is I am unable to get my IPv6 subnets into Sites and Services Where should I proceed from here?

  Read the article

• How do Windows 7 encrypted files look like?

  - by Sean Farrell

  Ok this is kind of an odd question: How do Windows 7 (Home Premium) encrypted files look like "from the outside"? Now here is the story. An acquaintance of a freind of mine got a nasty virus / scareware. So I wiped out my PC technician cap and went to work on it. What I did was remove the drive from the laptop and put drive into my external drive bay. I scanned the drive and yes it was loaded with stuff. That basically cured the infection and I could start the system back up. To check if it cured the problem I wanted to see the system while running. There where two user accounts, on with a password and one without (both admin users !?!). So I logged into the unprotected user and cleaned up the residual issues, like proxy server to localhost in the browser config. Now I wanted to do the same for the password protected user. What I noticed that from my system and the unprotected user account the files of the protected user looked garbled. The files are something like 12 random alphanum chars, but the folders looked ok. Naive as was thought this might be how encrypted files looked "from the outside". (I never use Microsoft's own security features, so how would I know. TrueCrypt is one big blob.) Since the second user could not be reached, I though sod it and removed the password from the account. (That might have been a mistake, I know.) Now I did the same clean up tasks and all nice and fine; except for the files which where still "encrypted". So I looked into many Windows Encrypted Files recovery posts and not all hope is lost, since I should be able to extract the certificate and with the password regain access to the files. Also note that windows did "only" prompt me that removing the password would be insecure, not that access to encrypted files would be lost, like it is claimed in most recovery articles. Resetting the password did not help and I gave up for the night. The question that nagged me half of the last night was, what if the files are not encrypted, but the scare-ware encrypted / destroyed the files? I don't want to spend hours of work trying to recover files that are not recoverable. The ting is that the user does not remember turning it on and aren't the files marked in blue and the filename is readable? Many thanks for input from users who have more knowledge about WEF...

  Read the article

• What's the best scenario for using a wireless router with Comcast Business Class

  - by Buck

  Just had Comcast Business Class internet installed (usage details at bottom of post). During the call to order I asked about the hardware they'd be providing and was told it was a docsis 3 modem that I'd have to pay $7.00/month for. Figuring I'd have to buy a router anyway, I decided to get my own modem - a Surfboard SB6121 Docsis 3. I called in to tech support to ask some questions and learned that the modem they would have provided DID have a router built in. It's an SMCD3G-CCR. It's not wireless (we need wireless). The guy explained that it was better to have their hardware here because if there's a problem with our service and we're using our own hardware, chances are they'll blame it on our hardware and do nothing since they don't support it. He explained that I could still hang my own wireless router off their modem/router and if we ever had any service problems, we'd be able to plug directly into their hardware and they'd be able to tell where the problem is and they wouldn't be able to pawn it off onto "customer provided equipment". That all said, a few questions: 1. Am I better off returning my Surfboard modem and getting the Comcast one? If I get a wireless router and plug into one of the ethernet ports of the Comcast device, should I NOT plug anything else into the Comcast device since it would be a different network from anything connecting via the wireless router? Is that correct? Given that I know VERY LITTLE about networking and setting up hardware like this... since I need wireless and will HAVE to get a wireless router to work with this Comcast device, do I need to do anything with the settings of the Comcast device? Do I use security on the Comcast device or the wireless router or both? Any suggestions or anything I need to think about, given this scenario, in order to use a business-type voip service like RingCentral or Jive or Nextiva? Any recommendations on a wireless router for this scenario? We are running 2 PCs (possibly 3-4 in the future) - could be wired for the time being if needed but would prefer wireless; would like to have a networked hard drive and a networked printer; NEED business-type VOIP service asap for 2 phone lines. Would like to hook up some IP cameras at some point (but not the kind that require static IPs since I don't have one nor do I plan to pay Comcast another $15/month for one). I don't have or plan to have any type of web servers or anything like that. Want to use WPA or WPA2 security and take advantage of the NAT feature of the router for additional protection (that's the extent of my networking knowledge).

  Read the article

• How to configure DD-WRT routing table when creating an isolated network segment for PCI C VT compliance

  - by tetranz

  I'm the volunteer support and system admin person at a small private school. We need to setup a PCI compliant Windows PC as a virtual terminal for credit card processing. I've read questionnaire SAQ C-VT and, to quote, this computer needs to be accessed: "via a computer that is isolated in a single location, and is not connected to other locations or systems within your environment (this can be achieved via a firewall or network segmentation to isolate the computer from other systems)" Our setup is as follows: DSL modem from ISP is setup to be a "transparent pipe" with no extra services. That goes into the WAN port of Linksys WRT54-GL running a DD-WRT. The LAN is 192.168.1.x. There are a couple of other WRT54-GL / DD-WRT devices. One is used as a wireless AP and another is a client bridge. To isolate the VT (virtual terminal) machine, I have another DD-WRT device. Its WAN is connected to a port on the 192.168.1.x LAN. The virtual terminal machine is connected to its LAN which is at 192.168.10.x. The SPI Firewall etc is turned on. It's basically the default DD-WRT gateway setup where the "ISP" is our own LAN. That's working. All incoming traffic to the VT machine is blocked, including from our own LAN. The VT can access the internet BUT, and here's the problem, it can also ping any of the computers on the 192.168.1.x LAN. I think I need to stop that. I'm guessing that I could do something with the Static Routing table in the VT machine's DD-WRT device. I need to route anything going to 192.168.1.x other than the gateway which is 192.168.1.1 to 0.0.0.0 or something like that. That's where I'm stuck at the end of my knowledge. Or ... do I need to get yet another DD-WRT so the network is "balanced". Maybe I need to have the internet from the DSL going into a DD-WRT which has only two devices on its LAN i.e., two other DD-WRTs, one for the main LAN and one for the VT. I think that would do but I'd like to avoid the extra cost and complexity if I don't need it. Thanks

  Read the article

• amazon ec2 ubuntu with gitlab and nginx - cant load?

  - by thebluefox

  Ok, so I've spooled up an Amazon EC2 server running Ubuntu, and then followed the instructions below to install GitLab; http://doc.gitlab.com/ce/install/installation.html The only step I've not been able to complete is running the following check on the status; sudo -u git -H bundle exec rake gitlab:check RAILS_ENV=production I get the following error; rake aborted! Errno::ENOMEM: Cannot allocate memory - whoami Which I presume is becuase my EC2 is just running a free tier setup, so isn't that well spec'd. Regardless, I've been trying to access this through my browser. I've set up the elastic IP and pointed my domain at it (for the purpose of this, lets say its git.mydom.co.uk). Doing a whois on this domain shows me its pointing to the right place. For some reason though, I get the "Oops, Chrome could not connect to git.mydom.co.uk". Now - for a period of time I was getting the Nginx holding page (telling me I still needed to perform configuration). This though disappeared after removing the default file from /etc/nginx/sites-enabled/ (after reading this could be issue on a troubleshooting page). Since then, I've had nothing, even when I symlinked the file back in from /sites-available. I've tried changing the owner of the git.mydom.co.uk file sat inside /sites-enabled and /sites-available to www-data, as suggested here, but I could only change the permission of the file in /sites-available, and not the symlinked one in /sites-enabled. The content of this file is as follows; upstream gitlab { server unix:/home/git/gitlab/tmp/sockets/gitlab.socket; } server { listen *:80 default_server; # e.g., listen 192.168.1.1:80; In most cases *:80 is a good idea server_name git.mydom.co.uk; # e.g., server_name source.example.com; server_tokens off; # don't show the version number, a security best practice root /home/git/gitlab/public; # Increase this if you want to upload large attachments # Or if you want to accept large git objects over http client_max_body_size 20m; # individual nginx logs for this gitlab vhost access_log /var/log/nginx/gitlab_access.log; error_log /var/log/nginx/gitlab_error.log; location / { # serve static files from defined root folder;. # @gitlab is a named location for the upstream fallback, see below try_files $uri $uri/index.html $uri.html @gitlab; } All the paths mentioned in here look ok...I'm about at the end of my knowledge now!

  Read the article

• What Sort of Server Setup Am I Likely to Need? - School A/V streaming

  - by DeathMagus

  My prior experience with servers has generally been limited to home file-sharing servers, low-traffic web-servers, and the like. This leaves me with the technical knowledge of how to set up a system, but little experience in terms of scaling said system. My current project, however, has me as the technical lead in setting up a school for online audio and video streaming. The difficulty I'm running into is that I don't quite have the experience to guess what they'll need, and they don't have the experience to tell me - so I've tried to ask as many pertinent questions about what they want to do with their server, and here's what I found out: About 1000 simultaneous users, and hoping to expand (possibly significantly) Both video and audio streaming, at obviously the highest quality possible Support for both live and playlist-based streaming. Probably only one channel, but as it's an educational opportunity, I imagine letting them have a few more wouldn't hurt. No word on whether they're locked into Windows or whether Linux is acceptable. Approximate budget - $7000. It may actually be about $2k less than this, because of a mishap with another technology firm (they ordered a $7000 DV tape deck for some reason, and now the company wants them to pay a 30% restocking fee). The tentative decisions I've already made: I'm planning on using Icecast 2 for my streaming server, fed by VLC Shoutcast encoding. Since the school already has a DMZ set up, I plan on placing the Icecast server in there, and feeding it through their intranet from a simple workstation computer in their studios. This system isn't in any way mission critical - it's an education tool (they're a media magnet school), so I figure redundancy is not worthwhile to them from a cost:benefit perspective. What I don't know is this: How powerful of a server will I need? What is likely to be my major throttle - bandwidth? How can I mitigate that? Will I need anything special for the encoding workstation other than professional video and audio capture cards and a copy of VLC? Are there any other considerations that I'm simply missing? Thanks a lot for any help - if there's more information you need, let me know and I'll tell you all I can.

  Read the article

• Spotlight Infinite Indexing issue (external data drive)

  - by Manca Weeks

  This is an external drive, formerly a boot drive which is now in use only to access music files (sibelius, audio, midi, live, logic etc.) without transferring the data into a new boot system, partly because of the issue I am about to describe, but mostly because the majority of the data is mainly there for archival purposes. The user is a composer and prominent musician and needs to be able to rehash the data at will. I have tried several things - here is a list: - make complete filesystem clone with antonio diaz's ddrescue - run Disk Warrior on copy, repair whatever errors occurred - wipe out all ACLs on entire drive - set all permissions to the same value - wide open 777 - remove any system data (applications, system files, including hidden files to the best of my knowledge) by selecting only non-system/app data and using Carbon Copy Cloner to put only the data of interest onto a newly formatted drive - transfer data to newly formatted drive folder by folder, resetting the spotlight index in between adding each to observe for issues (interesting here is that no issues occurred except for in Documents folder - when I transferred only the Documents folder to a newly formatted drive on its own - no trouble. It appears almost as thought it may not be the content but the quantity or specific combination of data that results in problems) - use DataRescue to transfer the data to yet another newly formatted drive to expose any missed hidden files Between each of the above steps I stopped Spotlight (search for anything beginning with md in Activity Monitor - All Processes and quitting it), deleted the .Spotlight-V100 directory from the affected drive. Restart Splotlight indexing by adding drive to Spotlight privacy list and removing it. In each case the same issue occurs - Spotlight begins indexing normally (or so it seems), then the index estimated time increases, usually to 4 hours remaining. This is where it gets stuck and continues to predict 4 hours remaining but never finishes. Sometimes I can't eject the drive and have to quit the md.. processes from Activity Monitor to be able to eject the drive without Force Eject. Once I disconnect the drive after the 4 hours remaining situation - if I reattach it, Spotlight forever estimates remaining time and never gets going again. So there it is. It is apparently not a filesystem issue, not a permissions issue and not tied to any particular piece of hardware or protocol (used USB and FW drives). I have tried this on several machines (3 to be precise) and in 10.5.8 and 10.6.5. Simply disabling Spotlight on this volume is not an option because the owner has no clue where things are as the data on the volume dates back to music projects and compositions from 2003 and before. He needs to be able to query for results. Anyone got any ideas? Thanks, M

  Read the article

• Educate me - should I buy these prebuilt NAS (which is better) or make my own?

  - by user29336

  I'm trying to learn as much as possible, and I think I've learned quite a bit so bear with me here under my confusion. I found a coupe NAS setups. I'm not sure if one is better than the other, other than the price being higher on some, and some coming with drives VS not. Let me list my setup so you can get an idea of what I want to provide: Macbook Pro Macbook Mini for Media streaming (so far) Windows 7 Gaming Computer Xbox 360 I'd like to provide a storage system for all these devices so they can access files very easily, I'd also like any of these devices to be able to stream media from this storage system. I'd like this storage system to be hassle free in terms of my confidence in the data integrity. If a drive fails, I want to know that I can replace the drive and all my files will still exist. I'd like to access this storage system OUTSIDE of my LAN. If I'm out on a job for work I'd like to go in, or be able to have people DL some files. This brings me to a question, is this what iSCSI is? I'd like this data system to be able to download torrents. I want to mount any drive on this storage system onto my OSX laptop as if it were a local drive attached. (Is this with iSCSI is?) I'd like this system to have a GOOD web based GUI. I don't want to install software to use it. I believe those are the most of my requirements. If I'm missing something that I have no knowledge about, can someone educate me? Here are the systems I found: $729ish on Newegg Lacie 5Big Network 2 (comes with 5TB of space. iSCSI / mac compatible, torrents, nice ui, + others?) Is this overpriced for what it provides? It almost seems like a great deal to me because of the 5TB of space it comes with vs the other NAS systems that don't come with storage but cost $600-700. Should I get a different NAS system? Netgear? Others? Do they have same features? Better? Is it better to buy your own disks? What about making my own? I'm tech savy all around. It seems cheaper to buy a premade one especially with the support/warranty it provides...

  Read the article

• What happens to missed writes after a zpool clear?

  - by Kevin

  I am trying to understand ZFS' behaviour under a specific condition, but the documentation is not very explicit about this so I'm left guessing. Suppose we have a zpool with redundancy. Take the following sequence of events: A problem arises in the connection between device D and the server. This causes a large number of failures and ZFS therefore faults the device, putting the pool in degraded state. While the pool is in degraded state, the pool is mutated (data is written and/or changed.) The connectivity issue is physically repaired such that device D is reliable again. Knowing that most data on D is valid, and not wanting to stress the pool with a resilver needlessly, the admin instead runs zpool clear pool D. This is indicated by Oracle's documentation as the appropriate action where the fault was due to a transient problem that has been corrected. I've read that zpool clear only clears the error counter, and restores the device to online status. However, this is a bit troubling, because if that's all it does, it will leave the pool in an inconsistent state! This is because mutations in step 2 will not have been successfully written to D. Instead, D will reflect the state of the pool prior to the connectivity failure. This is of course not the normative state for a zpool and could lead to hard data loss upon failure of another device - however, the pool status will not reflect this issue! I would at least assume based on ZFS' robust integrity mechanisms that an attempt to read the mutated data from D would catch the mistakes and repair them. However, this raises two problems: Reads are not guaranteed to hit all mutations unless a scrub is done; and Once ZFS does hit the mutated data, it (I'm guessing) might fault the drive again because it would appear to ZFS to be corrupting data, since it doesn't remember the previous write failures. Theoretically, ZFS could circumvent this problem by keeping track of mutations that occur during a degraded state, and writing them back to D when it's cleared. For some reason I suspect that's not what happens, though. I'm hoping someone with intimate knowledge of ZFS can shed some light on this aspect.

  Read the article

• Why would a process monitoring script use exit 1; on finding no problems?

  - by user568458

  General question: On a Linux (Centos) server, if a process monitoring script run by cron is set to close with exit 1; rather than exit 0; on finding that everything is okay and that no action is needed, is that a mistake? Or are there legitimate reasons for calling exit 1; instead of exit 0; on the "Everything's fine, no action needed" condition? exit 0; on finding no problems seems to me to be more appropriate. But maybe there's something I'm not aware of. For example, maybe there's something specific to Cron? Or maybe there's a convention in process monitoring scripts that 'failure' means 'this script failed to need to fix a problem' (rather than what I would expect which is that exit 1; would mean 'the process being monitored has failed'?) My specific case: I'm looking at a process monitoring script written by my web hosting company. By process monitoring script, I mean a script executed by Cron on a regular basis that checks if an important system process is running, and if it isn't running, takes actions such as mailing an administrator or restarting the process. Here's the (generalised) structure of their script, for a service running on port 8080 (in this case, Apache Tomcat): SERVICE=$(/usr/sbin/lsof -i tcp:8080 | wc -l); if [ $SERVICE != 0 ]; then exit 1; else #take action fi Seems simple enough even for someone with limited knowledge like me, except the exit 1; part seems odd. As I understand it, exit 0; closes a program and signifies to the parent that executed the program that everything is fine, exit n; where n0 and n<127 signifies that there has been some kind of error or problem. Here, their script seems to go against that rule - it calls exit 1; in the condition where everything is fine, and doesn't exit after taking remedial action in the problem condition. To me, this looks like a mistake - but my experience in this area is limited. Are there cases where calling exit 1; in the "Everything's fine, no action needed" condition is more appropriate than calling exit 0;? Or is it a mistake? Wider context is pretty simple. It's a Centos VPS, running Plesk. The script is being called by Cron via Plesk's "Scheduled tasks" Cron manager. There's no custom layer between Cron and this script that would respond in an unusual way to the exit call. It's a fairly average, almost out-of-the box Plesk-managed Centos VPS (in so far as there is such a thing). The process being monitored by this script is Apache Tomcat.

  Read the article

• What would cause my SendMail server not to acknowledge receiving a TCP Sequence?

  - by Mike B

  My TCP/IP Stack knowledge is a little rusty so please bear with me.... I have a CentOS 5.7 server with SendMail and am having seeing intermittent timeout issues sending email (particularly larger email) to other remote domains. It doesn't happen with all attachments or recipient domains. Just some. After some extended troubleshooting, I think I've narrowed it down to TCP Sequences not being acknowledged. Here's a breakdown of the TCP session from a packet capture I collected directly on my MTA (fooMTA): Packet 1 - 11: Standard TCP handshake followed by initial SMTP conversation. No errors. Packet #12 Recipient MTA: TCP sequence 231. Ack 91. Packet #13 FooMTA: TCP sequence 91. Ack 305. Packet #14 FooMTA: TCP sequence 1115. Ack 305. Packet #15 Recipient MTA: TCP sequence 305. Ack 2495. Packet #16 FooMTA: TCP sequence 2495. Ack 305. Packet #17 FooMTA: TCP sequence 5255. Ack 305. Packet #18: Recipient MTA: TCP sequence 305. Ack 5255. Packet #19: FooMTA: TCP sequence 6635. Ack 305. Packet #20: FooMTA: TCP sequence 8015. Ack 305. Packet #21: Recipient MTA: TCP Sequence 305. Ack 8015. Packet #22: FooMTA: TCP Sequence 10775. Ack 305. Packet #23: FooMTA: TCP Sequence 13535. Ack 305. Packet #24: Recipient MTA: TCP sequence 305. Ack 10775 Packet #25: FooMTA: TCP Sequence 14915. Ack 305 It keeps going like this with my server still thinking it hasn’t received sequence 305… in response the remote side eventually retransmits its prior data thinking that it never arrived. Eventually the gap gets so large that no new data is sent and the remote MTA keeps retransmitting old stuff. This contributes to an exponential backoff and eventually the remote side gives up. What’s strange to me is that I see the “missing” TCP sequence (305 in this case) arriving back to my server (via a packet capture collected directly from fooMTA) So I don’t get why my server keeps asking for it. Could this be firewall related? What would be the next step in troubleshooting?

  Read the article

• General guidelines / workflow to convert or transfer video "professionally"?

  - by cloneman

  I'm an IT "professional" who sometimes has to deal with small video conversion / video cutting projects, and I'd like to learn "the right way" to do this. Every time I search Google, there's always a disaster for weird, low-maturity trialware, or random forums threads from 3-4 years ago indicating various antiquated method to do it. The big question is the following: What are the "general" guidelines and tools to transcode video into some efficient (lossless?) intermediary, for editing purposes, for the purpose of eventually re-encoding it after? It seems to me like even the simplest of formats and tasks are a disaster of endless trial & error, or expertise only known by hardened experts who have a swiss army kife of weird conversion tools that they use, almost as if mounting an attack against the project. Here are a few cases in point: Simple VOB files extracted from DVD footage can't be imported into Adobe Premiere directly. Virtualdub is an old software people keep recommending but doesn't seem to support newer formats. I don't even know how to tell with certainty which codecs a video has, and weather the image is interlaced or not, and what resolution and codecs I'm dealing with. Problems: Choosing a wrong interlace option which diminishes quality Choosing a wrong pixel aspect ratio (stretches the image) Choosing a wrong "project type" in Premiere causing footage to require scaling Being forced to use some weird program that will have any number of negative effects What I'm looking for: Books or "Real knowledge" on format conversions, recognized tools, etc. that aren't some random forum guides on how to deal with video formats. Workflow guidelines on identifying a format going from one format to another without problems as mentioned above. Documentation on what programs like Adobe Premiere can and can't do with regards to formats, so that I don't use a wrench as a hammer. TL;DR How should you convert or "prepare" a video file to ensure it will be supported by Premiere for editing? Is premiere a suitable program to handle cropping, encoding, or should other tools be used for this, when making a video montage from a variety of source formats? What are some good books to read that specifically deal with converting videos that use any number of codecs?

  Read the article

• SQL SERVER – Beginning SQL Server: One Step at a Time – SQL Server Magazine

  - by pinaldave

  I am glad to announce that along with SQLAuthority.com, I will be blogging on the prominent site of SQL Server Magazine. My very first blog post there is already live; read here: Beginning SQL Server: One Step at a Time. My association with SQL Server Magazine has been quite long, I have written nearly 7 to 8 SQL Server articles for the print magazine and it has been a great experience. I used to stay in the United States at that time. I moved back to India for good, and during this process, I had put everything on hold for a while. Just like many things, “temporary” things become “permanent” – coming back to SQLMag was on hold for long time. Well, this New Year, things have changed – once again, I am back with my online presence at SQLMag.com. Everybody is a beginner at every task or activity at some point of his/her life: spelling words for the first time; learning how to drive for the first time, etc. No one is perfect at the start of any task, but every human is different. As time passes, we all develop our interests and begin to study our subject of interest. Most of us dream to get a job in the area of our study – however things change as time passes. I recently read somewhere online (I could not find the link again while writing this one) that all the successful people in various areas have never studied in the area in which they are successful. After going through a formal learning process of what we love, we refuse to stop learning, and we finally stop changing career and focus areas. We move, we dare and we progress. IT field is similar to our life. New IT professionals come to this field every day. There are two types of beginners – a) those who are associated with IT field but not familiar with other technologies, and b) those who are absolutely new to the IT field. Learning a new technology is always exciting and overwhelming for enthusiasts. I am working with database (in particular) for SQL Server for more than 7 years but I am still overwhelmed with so many things to learn. I continue to learn and I do not think that I should ever stop doing so. Just like everybody, I want to be in the race and get ahead in learning the technology. For the same, I am always looking for good guidance. I always try to find a good article, blog or book chapter, which can teach me what I really want to learn at this stage in my career and can be immensely helpful. Quite often, I prefer to read the material where the author does not judge me or assume my understanding. I like to read new concepts like a child, who takes his/her first steps of learning without any prior knowledge. Keeping my personal philosophy and preference in mind, I will be blogging on SQL Server Magazine site. I will be blogging on the beginners stuff. I will be blogging for them, who really want to start and make a mark in this area. I will be blogging for all those who have an extreme passion for learning. I am happy that this is a good start for this year. One of my resolutions is to help every beginner. It is totally possible that in future they all will grow and find the same article quite ‘easy‘ – well when that happens, it indicates the success of the article and material! Well, I encourage everybody to read my SQL Server Magazine blog – I will be blogging there frequently on various topics. To begin, we will be talking about performance tuning, and I assure that I will not shy away from other multiple areas. Read my SQL Server Magazine Blog: Beginning SQL Server: One Step at a Time I think the title says it all. Do leave your comments and feedback to indicate your preference of subject and interest. I am going to continue writing on subject, and the aim is of course to help grow in this field. Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Optimization, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority News, T SQL, Technology

  Read the article

< Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >