Search Results

Search found 13669 results on 547 pages for 'left handed'.

Page 397/547 | < Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >

• Laptop hangs on POST and does not finish except on rare occasions

  - by user1049697

  I have an old Toshiba Satellite A100 laptop that hangs on POST when I try to start it. On rare occasions it does finish the POST and boots Windows successfully, but most times it just finishes it partially and continues to hang. I can enter the BIOS though when it has frozen, but I have to open the DVD-drive first for some reason. The keyboard is not quite right either, and I can't navigate the BIOS properly because the arrow keys doesn't work. I tried an external keyboard, but the problem persisted. I have tried to remove the memory, hard drive, and battery to see if any of these were the problem, but it did not solve it. The one logical thing left to do would be to remove the CMOS battery, but the "brilliant" engineers at Toshiba have place it such that a complete disassembly of the machine is necessary. What this all boils down to is basically the question of whether I can "save" this machine and get it to boot properly, or if I should just send it off to recycling. I suspect it might need costly repairs, but I can't bring myself to throw it away before I have made sure it's completely dead.

  Read the article

• Optical Audio out stuck on on a MacBook

  - by Clinton Blackmore

  Apple have made an interesting headphone port for the MacBook (and some other Intel Mac models). It works like a standard jack: nothing plugged in - audio comes out of built-in speakers headphones/external speakers plugged in - plays through headphones/external speakers but you can also use a special adapter (which trips a tiny microswitch) to get an optical audio out signal (which you can presumably plug into a nice surround-sound system). This is all well and good except when, like auto-tracking, it doesn't work, and you are left with nothing to adjust. Users report that they get no sound when they have nothing plugged in and that a red light emanates from the headphone port. If you go to System Preferences - Sound - Output, it will say (IIRC) "Optical Out" instead of "Internal Speakers". The only solution I'm aware of is to try to reset the switch by inserting and removing a set of headphones or a toothpick, perhaps wiggling it inside of the port, and hoping that you luck out and get it. Are there other ways to fix this problem? Does anyone know where the microswitch is or have a good technique to reset it?

  Read the article

• Unable to remove Read-Only attribute from folder in Windows XP

  - by elcuco

  I have this directory which I cannot remove the read only attribute from. The computer is running XP SP2 (or SP3, not sure) and the directory sits in a NTFS file system. Looking into the web I found this: http://support.microsoft.com/kb/256614 which tells that if the directory is "customized" it's treated as a system folder and thus "read only". I don't think this is a scenario in my case, but anyway it's not helping, their recommendation is more or less: attr -r -s /d /s d:\data and this is not working for me. Any other ideas? More info: The directory is served to an HTTP server (wamp) and the directory is an SVN check out. What happens is that the web server cannot write files into the directory (imagechace from drupal is you are really interested). Edit 2: The original post claimed that the directory sits on a VFAT FS, however I booted Fedora 11 from livecd and the partition is marked as NTFS. Edit 3: I left the company which I worked on, on which this situation happened... so I cannot fully close this question. But things get even worse: I tested the "attr -r" answer I put, it did not work for me, and now the developer said that it worked for her. A nice WTF moment. Probably a reboot helped... Sorry for loosing details. If anyone has the same problem, and one of the answers helps him - please comment.

  Read the article

• Excel Help: Data Input Help

  - by B-Ballerl

  Everyday I download data from a site that will have rows each filled with individual data for clients. I'm able to input the data into excel as a whole but after that I'm having trouble figuring out how to put it into a chart. For example Web visits time. So say Client 1 stayed for 5 min increasing his total time on the site to 20 min and Client 2 stayed for 0 min keeping his time of 10 min and they were both registered on new years eve, and R1's last login was today and R2's was yesterday. (R for some reason repersents Client, no idea why...). Client 3 hasn't been on since he registered keeping his total at 4 min So my data would look something like this for Today (20110104) R1,20101231,20110104,20 R2,20101231,20110103,10 R3,20101231,20101231,4 And this for the day before (201101030), R1,20101231,20110102,15 R2,20101231,20110103,10 R3,20101231,20101231,4 I get about 200+ client rows each day where even the names of the Client list are changing. Is it possible to import the data each day and fill it in a excel sheet where the Client number is off on the left hand side in a table, and the amount of time (Whole Number ex. 4) each day it spends on the site extend to the right under it's specific date see Picture? I've manage to create a manual sheet but have been unsucessful at getting excel to do any of it for me. Here are two pictures:

  Read the article

• How to change my W2k8 System Partition?

  - by Chris May

  On my Windows 2008 server, my C: is 1.5 TB, and the partition is marked as: Healthy (Boot, Page File, Active, Crash Dump, Primary Partition) and somehow I ended up with a 2GB D: that is marked as Healthy (System). On this D: drive are only a few MB worth of files (bootmgr, boot folder, bootsect.bak), but all Windows files are on the c:. I've done everything I can to remove the (System) mark. I tried using bcdedit, I tried marking the C:partition as "Active", I tried using bootsect.exe to assign the C: drive as the boot partition. Maybe I didn't do one of those steps correct, but I've tried everything I can. When I got my new Dell Poweredge T710, I didn't bother removing their 2 small drives before I put in my 2 new large drives. So I think when I installed W2k8 Server, maybe dell left some bootable partition on their drives to help me install the OS, but I never used it and just booted right from the install CD. Can anyone help me remove the (System) mark from the D: so I can remove the D: partition and still boot to the C:? I know I could remove the D: drives and reinstall windows, but I'm trying to avoid a total reinstall.

  Read the article

• Tri-head linux system with Xmonad: is it possible to have HW acceleration

  - by progo

  What means there exists to have three monitors, all controlled by Xmonad and have hardware 3D acceleration as well? I had the pleasure of using three monitors earlier this year, and while Xmonad and Xinerama handle three monitors easily, I had to throw in an extra display driver, and also let go of Nvidia's own TwinView (which is a hack on Xinerama). This left me with no HW acceleration and some flickering as double buffering wouldn't work with certain applications. However, the three monitors handle so beautifully that I had hard time coming back to two. I understand the easiest way to achieve HW-accelerated tri-head combo is to split into two Xorgs. I wouldn't be able to switch windows between the Xorgs, so I'm not really into this solution. What's more, having a cheap and old PCI card along with even slightly better PCIe seemed to slow things down. Even if I occasionally disabled the third monitor from Xorg configure, I couldn't get HW acceleration to work. Only after I physically disconnected the old PCI card, I could get the games back in business. Would a Matrox Dual/Tri-head2go and a powerful Nvidia GPU do the trick? I understand Xmonad can be configured to "believe" that a "single" (as Dualhead2Go will merge) 3360x1050 display is actually two different ones? So that Xmonad's Mod-w and Mod-e would work properly there.

  Read the article

• Trying to delete directory with "rm -rf", but get message that it's not empty

  - by Ben Hocking

  I've tried deleting a directory using "rm -rf" and I'm getting the message "Directory not empty": Bens-MacBook-Pro:please benjaminhocking$ ls -lart empty_directory/ total 16 drwxr-xr-x 5 benjaminhocking staff 170 Aug 27 14:46 . drwxr-xr-x 3 benjaminhocking staff 102 Aug 27 15:28 .. Bens-MacBook-Pro:please benjaminhocking$ rm -rf empty_directory/ rm: empty_directory/: Directory not empty Bens-MacBook-Pro:please benjaminhocking$ rmdir empty_directory/ rmdir: empty_directory/: Directory not empty If I try the same thing using Finder (dragging the folder to the Trash), I get the message The operation can’t be completed because the item “empty_directory” is in use. I've tried doing xattr -d com.apple.quarantine, purely out of superstition, but it did no good. A probably important piece of context is that this directory was initially in a directory that should've been deleted by a "make clean" command I issued prior to Terminal locking up on me, after which a little over half of the other programs I had running also locked up, including Skype, and eventually the OS itself. I ended up having to reboot the computer by pressing and holding the power key. Edit to add: Another important piece of information I left off was that this was happening in an encrypted folder à la encfs. I was able to track down the corresponding folder in the encrypted side of things and delete it there. I still don't know why I couldn't do it from the decrypted side of things like I normally do. I'll leave this unanswered for now in case anyone has a good answer for that.

  Read the article

• Websockets Server with Fault-Tolerance and Durable Message Store

  - by smitchell360

  I am starting to experiment with websockets. Does anyone know of a websockets server (open source or paid) that provides a durable store of the websocket "channel"? All of the examples that I have found do not address durability -- if a websockets server goes down, all "channel" data is lost. Services such as Pusher do not really discuss whether they address the durability issue (and I have not received a response from tech support yet). Happy to roll my own, but would rather not reinvent the wheel. EDIT: I'm not looking for websockets 101 information. That is readily available and understood. I'm looking for a server (open source or paid) that supports websockets and has a durable store for the websocket data so that, in the event that a server fails, a new server can take over where the original one left off. Two main purposes: 1. support failover scenarios contemplated by the websockets Network Working Group http://tools.ietf.org/html/draft-ibc-websocket-dns-srv-02#section-5.1 (most importantly so that missed messages are sent when a client connects to a failover server) 2. support scenarios where new subscribers must receive all past messages that were published. Of course this can be handled at the application layer...but that is not what I am looking for. EDIT So, after some research the following installed options seem to be the most robust: Kaazing Migratory Migratory (http://migratory.ro) Hosted services that seem "real" Pusher (great API but no history feature yet) PubNub (has history) All of the above services have graceful fallback to other communication methods if websockets are not available. I was not able to find any open source that provided "out of the box" clustering, fail-over, and a durable message store to play back history. There are some projects that may serve as good starting points, but not exactly what I am looking for.

  Read the article

• how to back up data from a machine that keeps hanging

  - by Amit Phatarphekar

  Hello - I have a storage server running opensolaris. But lately its been acting up - it hangs at random times due to some SCSI/ATA related error messages. I've tried to fix it without any progress, so I'm giving up now. The machine keeps hanging every 30 minutes or 1 hr ...sometimes after 4 hrs. Its very unpredictable. So I've decided to just reformat the storage server and start from scratch...maybe I'll just not use solaris and install something else, since the errors are related to solaris running on ATA HDD or something. Question - Before I reformat it, I want to back up some of the important data on it. Like it has a VM with 200 GB disk files, it has a whole bunch of ISOs stored on it etc etc. I'm using a simple scp to copy the files over to a different machine. My issue is that, because the machine hangs....sometimes my file copy is incomplete and I have to start all over again. Lets say I'm trying to copy a 200GB file which takes like 4 hrs....IF the machine hangs before the whole file i copied over...I have to recopy the file from scratch. Is there a solution to copy the files over such that if the machine hangs or network goes down..the copying can resume from where it left off? - like if 50 GB of a 200GB file was copied and machine hung....next time, it'll just continue to copy rest of the amount, instead of starting all over again. Thanks Amit

  Read the article

• Degraded RAID-5 array with lvm2 lost superblock and partition table

  - by Fred Phillips

  I have a RAID-5 array of 4x1TB hard disks with one lvm2 partition on Ubuntu Linux 10.04 LTS. One of the disks has failed. I have re-assembled the array without this failed disk but now mdadm --examine claims the array has no superblock and fdisk says it has no partition table. What can I do to recover the data? # mdadm -D /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sat Mar 5 14:43:49 2011 Raid Level : raid5 Array Size : 2930276352 (2794.53 GiB 3000.60 GB) Used Dev Size : 976758784 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Sat Mar 5 15:06:49 2011 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 1 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Name : boba:1 (local to host boba) UUID : 52eb4bc9:c3d8aab5:e0699505:e0e1aa05 Events : 18 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 65 1 active sync /dev/sde1 2 8 49 2 active sync /dev/sdd1 3 0 0 3 removed 4 8 17 - faulty spare /dev/sdb1 # mdadm --examine /dev/md0 mdadm: No md superblock detected on /dev/md0. # fdisk -l /dev/md0 Disk /dev/md0: 3000.6 GB, 3000602984448 bytes 2 heads, 4 sectors/track, 732569088 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1572864 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] [linear] [multipath] [raid0] [raid1] [raid10] md0 : active raid5 sdb1[4](F) sda1[0] sdd1[2] sde1[1] 2930276352 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_] unused devices: <none>

  Read the article

• Underbraces in Word math zones and dealing with stretchy parentheses

  - by Johannes Rössel

  Parentheses in Word usually stretch with whatever they're containing. This might be un-noticeable for things like but for stuff like it's definitely nice, especially compared to the fact that naïve LaTeX users often produce uglinesses such as There is a problem, however, when using under-/overbraces in math and putting parentheses around the complete term it becomes ugly. For simple things like shown here this can be solved by not letting the parentheses stretch which looks almost right. However, for more complex things it's certainly not an option: Both variants look horrible. So is there a way of letting the parentheses only stretch around the actual term parts, not including the under-/overbraces? Those are frequently used for annotations of individual pieces, so simply not using them is a bad idea too. In LaTeX you can get away with guesswork and using explicit sizes for the parentheses instead of relying on \left and \right but I haven't found a comparable option in Word yet. Since the underbrace is (tree-wise) a sibling of the term in parentheses it probably simply has to stretch and there probably can't be an algorithm that determines when to stretch or when not, considering that \above and \below are used for annotations as well but also for other things where perentheses have to stretch. Also, since the parenthesized expression is opaque from the outside one has to put the underbrace inside. From a markup point of view, at least. One can probably draw the rest around but that falls apart when styles change and wouldn't be a good idea either.

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• Tips and Suggestions IP Address Re-Addressing?

  - by RSXAdmin

  Hello serverfault Universe, My ever evolving and expanding local area network is currently using a class-C address. My network consists of multiple subnets depending on site/location. 192.168.1.x is site HQ 192.168.5.x is secondary site 192.168.10.x is so on and so forth. Long story short - I have inherited this network design from the previous admin who has left the company which started off with a dozen people and now has just over 300 full time/part time employees. We do not yet have client VPN access; but we do have site to site VPN setup. My question is, in preparation for outside client access to my network via Cisco ASA, I would like to re-address the HQ site because I understand a 192.168.1.x or 192.168.0.x are not very good choices for a company subnet - it may conflict with a home user's LAN when connecting to my LAN, I believe? Through your experience, does anyone out there have any suggestions and tips on how I can proceed with re-addressing my subnets. If I designed this network I would have gone with a 10.0.0.0 (mask 255.255.255.0) so I am leaning towards changing it to fit. Thank you.

  Read the article

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• Desktop bigger than screen

  - by alex

  I am using MSI U115 11" netbook (OS: Windows XP Home, graphics card: Intel Graphics Media Accelerator 500) and today after I switched it on, desktop was bigger than screen. To be exact: screen resolution was set to the lowest possible and I could move mouse outside of screen (but only below - left, right and up worked normally, mouse could not exceed screen boundaries). I changed resolution back to normal, but the problem with desktop being bigger than screen remained (as before, only lower part - cannot see task bar, etc. When I hit windows button on keyboard, only upper part of menu start is visible). What I already tried was changing all kind of graphics and screen settings - none of them helped. I also tried to restore the system to few days before, but it didn't help neither. What can I do to make the desktop look "normally"? EDIT: Some additional info regarding screen: Sorry it's in polish - but let me explain. There are two screens I can choose (Monitor domyslny means default screen), but the second one (the default one) is not available. After I choose it and click apply number 1. is used (and as you can see it has only two resolutions available. There are more in the second one - but without 1024x600 though). The two ticked and grayed out options here are Use this screen as the main one and Enlarge Windows desktop to match this monitor's size. Too bad I cannot change them. When I choose the second screen, the first box is unchecked and grayed out. The second box is available to be changed but it doesn't matter anyway as after applying changes it reverts to the first screen anyway. EDIT: Intel Graphics Media Control Panel screenshot.

  Read the article

• Group policy not applying to security group

  - by ihavenoideawhatimdoing

  Preface: I have enough privileges to create GPOs in my OU, and have made a few of them for some simple tasks (like deploying a printer to certain users). Not actually a sysadmin...I'm a developer who is winging it. I wanted to create a GPO that would set a mapped folder for a certain security group (which I recently created and that contains only myself). Did the following: Created the GPO in MyOU - Users Removed the default Authenticted Users under Security Filtering Add the security group with my account to Security Filtering Set up the mapping via the User Configuration option Changed GPO Status to "Computer configuration settings disabled" Left WMI filtering to Closed the GPO at this point... Logged in as the target user; ran gpupdate /force Logged out, logged in, ran gpresult /r, no mention of my GPO Rebooted Logged in, re-ran gpupdate /force Logged out, logged in, ran gpresult /r, still no mention of my GPO If I log in with another completely different user, their RSOP information shows that the new GPO is being ignored due to a security restriction, so it appears to be "working" for other users. I just can't get it to actually show up in RSOP for the user it should be working. Is there anything else I can do short of rebooting endlessly and crossing my fingers?

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  I'm having some problems installing CentOS 5.5 Final (i386) onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up and gives you the option on how to boot into the DVD, I'll press enter to go into the graphical installer. The screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours). I then booted into it again and tried using Linux Text thinking it was a problem with the graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point I think it's a hardware problem. The server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) configured for RAID 0. (There is also an option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. Edit Typing "text" doesn't change a thing. Still stuck at the blinking cursor. I looked it up and it's really the same thing as typing "linux text", which as stated in the first part of my question, I've already done.

  Read the article

• How does one open multiple tabs in TextWrangler?

  - by Closure Cowboy

  No, I'm not bluffing. I really can't figure this out. The setup: I went to File -> Open, and then selected a directory rather than a file. As expected, a directory tree opened on the left side of my document. Hooray! I can easily view the files' structure in my Rails project. So, I make a few changes in a file, and then I click on a different file in the directory tree. My problem: TextWrangler then asks me whether I want to save my changes. Huh? I say "No", and the new document doesn't open at all. Great. I try hitting Command+N (new document). A new window opens. Ughhhh. How the heck do I open documents in a new tab? Note: I have set the "New & opened documents" behavior to "Open in the front window". This does not change the behavior described (i.e. when a directory is opened rather than a single file).

  Read the article

• How can I set the CD audio volume in Linux?

  - by user1296362

  In Windows 7 Control Panel - Sound - Sound Properties window there's an slider for setting CD Audio volume: And it's pretty strange that I can't find corresponding one in generic Linux mixers: alsamixer or amixer. I connected a CD drive to try to set CD audio volume with cdcd (CD Player): $ cdcd setvol 0 Invalid volume It isn't actually an invalid volume, it is because ioctl() call fails. I found that out after searching and changing a bit the source code of this utility (in the libcdaudio): --- cdaudio.c.orig 2004-09-09 06:26:20.000000000 +0600 +++ cdaudio.c 2012-05-30 21:34:34.167915521 +0600 @@ -578,8 +578,10 @@ cdvol_data.CDVOLCTRL_BACK_RIGHT_SELECT = CDAUDIO_MAX_VOLUME; #endif - if(ioctl(cd_desc, CDAUDIO_SET_VOLUME, &cdvol) < 0) - return -1; + if(ioctl(cd_desc, CDAUDIO_SET_VOLUME, &cdvol) < 0) { + printf("*** cd_set_volume: ioctl() returned error\n"); + return -1; + } return 0; } By the way cdcd's get volume command yields rather weird output: Left Right Front 1281734864 32767 Back 0 0 Also I tried aumix: $ aumix -c 0 But all with no success. I read from this manual — http://tldp.org/HOWTO/Alsa-sound-6.html (section 6.2 The mixer) that CD channel can present in amixer output. Maybe some drivers for sound card are missing in my Ubuntu 12.04 LTS installation. Though I don't think it's the case: $ lsmod | grep snd snd_mixer_oss 22602 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 223867 1 snd_hda_intel 33773 4 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 19 snd_mixer_oss,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep ,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm All I need is just mute or set to 0 volume level of CD Audio channel, like I did in Windows 7, to get rid of sibilant noise in the speakers.

  Read the article

• how to prevent other computers from seeing our network computers through vpn

  - by Disco

  We have a local office domain consisting of Windows 7 and XP machines that is running on Windows Server 2008 R2. We also have users that connect via VPN into our network. My concern is that when a remote user opens up a folder, the Network section on the left side of the folder shows the remote user all the computer names in our local network. I would like to go about renaming our computers in the local network with more descriptive computer names, but I do not want the users off-site to be able to see these computer names by simply opening up a folder. (Granted, they can already do this, but our current naming scheme does not link computer names to users.) I would like to change our computer names so we can determine which computer belongs to which user more easily IF it can be done securely. How can I ensure that our local computer names are not showing up in the Network folder for remote, VPN-connected users? My online searches have turned up results where people are advised to turn off Network Sharing and Discovery, but that seems to only ensure that the local machine doesn't see other computer names. I want to prevent OUR computer names from showing up on OTHER computers, and I can't go into the VPN-connected computers and turn off THEIR Network Discovery settings. I would think there is a group policy that would control this but I have not found one yet and I don't know how I would apply it to VPN-connected computers. Thanks! EDIT: That's true, a Group Policy wouldn't run on users only connecting via VPN, good point. What about a VPN/router policy, then?

  Read the article

• Estimating compressed file size using a list parameter

  - by Sai

  I am currently compressing a list of files from a directory in the following format: tar -cvjf test_1.tar.gz -T test_1.lst --no-recursion The above command will compress only those files mentioned in the list. I am doing this because this list is generated such that it fits a DVD. However, during compression the compression rate decreases the estimated file size and there is abundant space left in the DVD. This is something like a Knapsack algorithm. I would like to estimate the compressed file size and add some more files to the list. I found that it is possible to estimate file size using the following command: tar -cjf - Folder/ | wc -c This command does not take a list parameter. Is there a way to estimate compressed file size? I am also looking into options like perl scripts etc. Edit: I think I should provide more information since I have been doing a lot of web search. I came across a perl script(Link)that sort of emulates the Knapsack algorithm. The current problem with the above mentioned script is that it splits the files in their original state. When I compress the files after splitting them, there are opportunities for adding more files which I consider to be inefficient. There are 2 ways I could resolve the inefficiency: a) Compress individual files and save them in a directory using a script. The compressed file could provide a best estimate. I could generate a script using a folder of compressed files and use them on the uncompressed ones. b) Check whether the compressed file's size is less than the required size. If so, I should keep adding files until I meet the requirement. However, the addition of new files to the compressed file is an optimization problem by itself.

  Read the article

• My iPod never finishes syncing and only syncs audio, not pictures or video - any ideas as to how I c

  - by Sam Meldrum

  My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated?

  Read the article

• Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

  - by Wesley

  Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

  Read the article

• L2TP over IPSec VPN with OpenSwan and XL2TPD can't connect, timeout on Centos 6

  - by Disco

  I'm setting up LT2p over IPSec on my Centos 6.3 fresh install. I have iptables flushed, permit all. Whenever I try to connect, i get a 'no reply from vpn' and nothi Here's my ipsec.conf file (Server is 1.2.3.4) : config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=1.2.3.4 leftprotoport=17/1701 right=%any rightprotoport=17/%any My /etc/ipsec.secrets 1.2.3.4 %any: PSK "password" My sysctl.conf (appened lines) net.ipv4.ip_forward = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.default.send_redirects = 0 net.ipv4.conf.all.log_martians = 0 net.ipv4.conf.default.log_martians = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv4.icmp_ignore_bogus_error_responses = 1 Here's what 'ipsec verify' gives: # ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.32/K2.6.32-279.19.1.el6.x86_64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] And I see xl2tpd is listening on 1701/udp : udp 0 0 1.2.3.4:1701 0.0.0.0:* 2096/xl2tpd

  Read the article

• Visual Studio 2010 Beta 2, built-in font smoothing

  - by L. Shaydariv

  I've just installed Visual Studio 2010 Beta 2 onto my Windows XP to evaluate it and check whether it meets my preferences the way it did before. Okay, I've temporary defeated an urgent bug with a strange workaround (I could not open any file from the Solution Explorer), and it left bad memories to me. But however, it's okay. The first thing I've seen just opening the code editor was ClearType font rendering. Wow, so unexpectedly. I must note that I do not use standard Windows rendering techniques, but I still prefer GDI++, a font renderer developed by Japanese developers. (GDI++ allows to render the fonts in Mac/Win-Safari style over entire Windows.) Personally for me, GDI++ reaches the great font-rendering results allowing me to use the Dejavu Sans Mono font with really nice smoothing in Visual Studio 2008 (VS 2005 too, though VS 2005 crashes in this case). But GDI++ cannot affect Visual Studio 2010 Beta 2 text editor - it uses ClearType (right?), and it does not care about the system font smoothing settings. It could be an editor based on WPF, right? So as far as I can see, I can't use GDI++ anymore because it uses Windows GDI(+) but no WPF? So I've got several questions: Is it possible to disable VS 2010 b2 built-in ClearType or override it with another font smoother? Is it possible to install a Safari-like font renderer for Visual Studio 2010 [betas]? Thanks a lot.

  Read the article

< Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >