Search Results

Search found 12497 results on 500 pages for 'linked servers'.

Page 398/500 | < Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >

  • Application stuck in TCP retransmit

    - by SandeepJ
    I am running Linux kernel 3.13 (Ubuntu 14.04) on two Virtual Machines each of which operates inside two different servers running ESXi 5.1. There is a zeromq client-server application running between the two VMs. After running for about 10-30 minutes, this application consistently hangs due to inability to retransmit a lost packet. When I run the same setup over Ubuntu 12.04 (Linux 3.11), the application never fails If you notice below, "ss" (socket statistics) shows 1 packet lost, sk_wmem_queued of 14110 (i.e. w14110) and a high rto (120000). State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 12350 192.168.2.122:41808 192.168.2.172:55550 timer:(on,16sec,10) uid:1000 ino:35042 sk:ffff880035bcb100 <- skmem:(r0,rb648720,t0,tb1164800,f2274,w14110,o0,bl0) ts sack cubic wscale:7,7 rto:120000 rtt:7.5/3 ato:40 mss:8948 cwnd:1 ssthresh:21 send 9.5Mbps unacked:1 retrans:1/10 lost:1 rcv_rtt:1476 rcv_space:37621 Since this has happened so consistently, I was able to capture the TCP log in wireshark. I found that the packet which is lost does get retransmitted and even acknowledged by the TCP in the other OS (the sequence number is seen in the ACK), but the sender doesn't seem to understand this ACK and continues retransmitting. MTU is 9000 on both virtual machines and througout the route. The packets being sent are large in size. As I said earlier, this does not happen on Ubuntu 12.04 (kernel 3.11). So I did a diff on the TCP config options (seen via "sysctl -a |grep tcp ") between 14.04 and 12.04 and found the following differences. I also noticed that net.ipv4.tcp_mtu_probing=0 in both configurations. Left side is 3.11, right side is 3.13 <<net.ipv4.tcp_abc = 0 <<net.ipv4.tcp_cookie_size = 0 <<net.ipv4.tcp_dma_copybreak = 4096 14c11 << net.ipv4.tcp_early_retrans = 2 --- >> net.ipv4.tcp_early_retrans = 3 17c14 << net.ipv4.tcp_fastopen = 0 >> net.ipv4.tcp_fastopen = 1 20d16 << net.ipv4.tcp_frto_response = 0 26,27c22 << net.ipv4.tcp_max_orphans = 16384 << net.ipv4.tcp_max_ssthresh = 0 >> net.ipv4.tcp_max_orphans = 4096 29,30c24,25 << net.ipv4.tcp_max_tw_buckets = 16384 << net.ipv4.tcp_mem = 94377 125837 188754 >> net.ipv4.tcp_max_tw_buckets = 4096 >> net.ipv4.tcp_mem = 23352 31138 46704 34a30 >> net.ipv4.tcp_notsent_lowat = -1 My question to the networking experts on this forum : Are there any other debugging tools or options I can install/enable to dig further into why this TCP retransmit failure is occurring so consistently ? Are there any configuration changes which might account for this weird behaviour.

    Read the article

  • Down to the Wire - Yet More Solaris Things to See at OpenWorld (and JavaOne!)

    - by Larry Wake
    San Francisco is bracing for the annual invasion. The airport's jammed, the tweets are flying, and the numbers are crazy: more than 50,000 attendees and 2,500+ sessions, taking over Moscone Convention Center, two streets, Union Square, and seemingly every hotel in town (98,000 hotel room nights). So yeah, it's busy. And it's not just OpenWorld--we've also got JavaOne, MySQL Connect, and four other sub-events going on as well. Speaking of JavaOne, you can find Solaris-related activity there, too -- I've highlighted one hands-on lab below. Here's a last pre-event roundup of activities for consideration; enjoy the show(s)! (Remember, Schedule Builder is your friend; use it with the session numbers below to register.) Monday, October 1st: 3:15 PM - General Session: Accelerate Your Business with the Oracle Hardware Advantage(GEN9691, Moscone North Hall D) John Fowler, head of Oracle's Systems organization, will talk about Oracle hardware technology and how it's co-engineered with other key technologies, including Oracle Solaris. Tuesday, October 2nd: 10:15 AM - Building an IaaS Platform with SPARC, Oracle Solaris 11, and Oracle VM Server for SPARC(CON4431, Moscone South 270)Get the birds-eye lowdown (whatever that means) on how U.S. Cellular  built its Infrastructure as a Service (IaaS) cloud delivery platform with Oracle’s SPARC T4 servers, Oracle Solaris 11, Oracle Solaris Cluster 4, and Oracle VM Server for SPARC. The session covers the high-level design, business case made, implementation details, and lessons learned. 11:45 AM - Oracle Solaris 11 Panel: Insights and Directions from Oracle Solaris Core Engineering(CON8790, Moscone South 252) This has been one of the livelier Solaris-related sessions in years past (and I'm not saying that just because I get to moderate it this year). A panel of core engineers responsible for a wide range of key Solaris technologies will talk about some of the interesting work they've been doing -- but mostly we keep time open for the panel to take questions from attendees, because that's the fun part. Wednesday, October 3rd: 10:00 AM - Tracing Your Java Application Tuning on Oracle Solaris with DTrace(HOL10214, Hilton San Francisco, Franciscan A/B/C/D) This JavaOne hands-on lab will show how to use the DTrace framework to dynamically trace your Java applications on Oracle Solaris and uncover new tuning opportunities. Thursday, October 4th: 12:45 PM - Oracle Solaris 11: Optimized for Oracle Database, Oracle WebLogic Server, and Java(CON8800, Moscone South 252) Explore how Oracle Solaris 11 has been built to be the best platform for the cloud and enterprise applications, with built-in optimizations to improve performance and deliver unique functionality with Oracle Database, Oracle WebLogic Server, and Java.

    Read the article

  • SPARC T4 ?????????

    - by user12798668
    ????????????????????????????????????????????????????? SPARC T4 ????????????????????????????T4 ??????? SP(Service Processor) ??? ILOM ?? - set /SP/powermgmt policy=elastic ?????????????????????????????????????????????????????????????????????????????????????????ILOM ? /SYS/VSP/history/0 ???????????????????????????? SPARC T4-1 ? OS ??????????????????????????????????????????????????????????? ?? ?? = ?????(W)?????????????? Mar 26 12:04:54 = 294 Mar 26 12:03:53 = 292 Mar 26 12:02:53 = 292 Mar 26 12:01:53 = 293 Mar 26 12:00:53 = 292 Mar 26 11:59:53 = 293 Mar 26 11:58:54 = 293 Mar 26 11:57:54 = 294 Mar 26 11:56:54 = 293 Mar 26 11:55:54 = 348 ????????????????????? 90W ?????????! ?? psrinfo ????????????????... # psrinfo 0 on-line since 03/23/2012 17:39:28 1 on-line since 03/26/2012 20:53:56 ?? SPARC T4-1 ????????8 ????????? 8 CPU ??????? SPARC T4 CPU ? 1 ??????????????psrinfo ??????? 64 CPU ??? OS ?????????????????????? 2 CPU ??????????! ???????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????CPU ??????????????????????????????????????????????????????????????????????????????????????????????????????? 2 CPU ?????????????????????????????????? CPU ????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ??????????? SPARC T4 ????????????? Oracle VM Server for SPARC (OVM for SPARC) ?????????????????????????????????????????????????? Oracle VM Server for SPARC ???????????? ?10? ??????? - ??????? ??????????????????????????OTN ? How to Use the Power Management Controls on SPARC Servers ?????????????????????????????? ??????????????SPARC T4 ?????????????????? Oracle OpenWorld Tokyo 2012 ???????????????????? ?????????????????????????·????????????????????! 4/4(?) ???? K1-01?ENGINEERED FOR INNOVATION ???????????????(9:00-11:15) 4/5(?) ????????? G2-01 ???????&???????????IT???????????(11:50 - 13:20) ???????????!! Oracle OpenWorld Tokyo 2012 ???? URL http://www.oracle.com/openworld/jp-ja/index.html ?????? 7264 ???????????????

    Read the article

  • PXE boot linux. PXE-E51: No DHCP or proxyDHCP offers were received

    - by athspk
    I am trying to have an ubuntu box (192.168.10.9) acting as a PXE server, but i have trouble getting DHCP to work. The PXE server is connected to a SOHO router (192.168.10.1) acting as a switch. I have disabled the DHCP server on the router. $ dhcpd --version isc-dhcpd-4.2.4 The contents of /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name-servers 192.168.10.1; default-lease-time 3600; max-lease-time 7200; authoritative; log-facility local7; allow booting; allow bootp; subnet 192.168.10.0 netmask 255.255.255.0 { range dynamic-bootp 192.168.10.101 192.168.10.200; option routers 192.168.10.1; option broadcast-address 192.168.10.255; next-server 192.168.10.9; filename "/tftpboot/pxelinux.0"; } The contents of /etc/default/isc-dhcp-server INTERFACES="eth0" When the client boots, it tries to get an IP address from the server but fails with the following Error message: PXE-E51: No DHCP or proxyDHCP offers were received. On Server side, i was tailing /var/log/syslog while the client tries to boot: Dec 4 12:57:10 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:11 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:12 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:12 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:17 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:17 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:25 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:25 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Please advise. Thanks in advance

    Read the article

  • Windows Server 2008 R2 Error CAPI2 Event ID 4107

    - by umar bhatti
    I am getting following error on couple of my 2008 R2 servers. I have tried couple of fixes which didn't fix the issues. Log Name: Application Source: Microsoft-Windows-CAPI2 Date: 18/03/2013 09:48:40 Event ID: 4107 Task Category: None Level: Error Keywords: Classic User: N/A Computer: ServerName Description: Failed extract of third-party root list from auto update cab at: <http://ctldl.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab> with error: The data is invalid. . Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-CAPI2" Guid="{5bbca4a8-b209-48dc-a8c7-b23d3e5216fb}" EventSourceName="Microsoft-Windows-CAPI2" /> <EventID Qualifiers="0">4107</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2013-03-18T09:48:40.169581600Z" /> <EventRecordID>8713</EventRecordID> <Correlation /> <Execution ProcessID="412" ThreadID="5288" /> <Channel>Application</Channel> <Computer>ServerName <Security /> </System> <EventData> <Data>http://ctldl.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab</Data> <Data>The data is invalid. </Data> </EventData> </Event>

    Read the article

  • iScsiPrt error event ID 5

    - by AZee
    Event Log: "Failed to setup initiator portal. Error status is given in the dump data." This is being recorded every 3/100's of a second. We are using MS iSCSI Initiator on Windows Server 2003, Dell 2970 w/4GB (PAE). I am sure that this was configured by Dell initially. I have no idea what changes or mods were made since the company installed this machine until now. (I'm a new User so the lovely and vibrant screen images had to be removed. They were quite pretty and I am sure you would have been very moved and appreciative of them.) It appears that everything is installed correctly and the 5TB bound volume is accessible but I have never worked with iScsi before so I plead total ignorance. In searching I have found this to be a fairly sparce and bland documented subject. I'd like two things... First, to get rid of the error msg being logged. MS says it can be ignored if everything is working but it chews up resources logging it and I don't feel comfortable about any errors on my servers. I want to correct whatever is causing this problem. Secondly, being totally green to this, I would like to confirm that the setup is optimized and we are taking advantage of all features available. Although there are 3 NIC's in this machine it appears that the initiator is only configured for the Broadcom BMC5708C NetXtreme II on our 10.90.1.#, the other 2 NICS are 1GB on the 192.168.0.#. Would additional targets improve performance? If someone who is experienced in configuring the Microsoft iScsi Initiator can help I would really appreciate it since, as I mentioned, everything I have come across has not been of any value at all. Thanks! ~AZ

    Read the article

  • Problems with cross forest authentication in SQL Reporting

    - by chunkyb2002
    We're currently running an SQL 2008 R2 Cluster with Reporting Services running, all for use with System Center Operations Manager 2007 R2 (RU3). Our users are on a different domains to the SCOM and SQL servers (we have two domains as we are in the process of a domain migration) We have no problems at all with users accessing reports via the SCOM Console or the Web interface if they are on the new domain which runs at 2008 R2 functional level. However users on the old domain (which runs at a 2003 functional level) cannot access reports on SCOM or via the web interface (http://sqlserver/reports) The error we get is: An error occurred when invoking the authorization extension. (rsAuthorizationExtensionError) For more information about this error navigate to the report server on the local server machine, or enable remote errors Taking the errors advise we logged on to the SQL server as a user on the old domain (which works fine!) and then try to authenticate with the reporting via the web interface which produces this most useful of errors: An error occurred when invoking the authorization extension. (rsAuthorizationExtensionError) The creator of this fault did not specify a Reason. Things we've tried: Recreating the trust between domains Ensuring the SQL Reporting service account was a member of Windows Authorization Access Group on the 2003 domain Added users on the 2003 domain explicitly to the Reporting Users group on the SQL Server Has anyone come across this issue before perhaps in a different scenario? If so how was it resolved? Thanks in advance for any help.

    Read the article

  • Remote Desktop - remote computer that was reached is not the one you specified

    - by Jim McKeeth
    We just setup some new Windows 2008 R2 servers and we are unable to Remote Desktop into them from our Windows 7 desktops. Remote desktop connects, but after we provide credentials we get: The connection cannot be completed because the remote computer that was reached is not the one you specified. This could be caused by an outdated entry in the DNS cache. Try using the IP address of the computer instead of the name. If we connect from Windows 7 to a machine not running Windows 2008 R2, or from a machine not running Windows 7 to the Windows 2008 R2 server, it works fine. Likewise if we connect to the Windows 2008 R2 server from Windows 7 via the IP address then it works fine (although that causes other problems later). I've only found one other mention of someone having this problem, so I don't think it is just our network. Any suggestions on how to connect from Windows 7 to Windows 2008 R2 via DNS? Both are 64-bit. Update: Turns out it does not need to be R2 to get the error. We have another server that is Windows 2008 R1 64-bit that also fails.

    Read the article

  • SChannel "cannot find certificate in either LocalMachine or CurrentUser store"

    - by Chris J
    We have an in-house application that requires the use of client SSL certificates to authenticate with a remote server (not under our control). This has worked without problems before but on deploying to a new server, we're having problems getting Windows 2008 to use the certificate. The certificate exists as a .pfx file that contains a private key. The same certificate exists in the LocalMachine store, again with its private key. We've ensured the one in the LocalMachine store is correct by creating a website in IIS against that certificate, so we're happy that the certificate, certificate chain, and private key is valid. The PFX has been created by exporting from the Certificates MMC snap-in. The issue is that we get the following in the system diagnostic logs that suggests it can't find the private key: System.Net Information: 0 : [5988] SecureChannel#23264094 – Locating the private key for the certificate: [Subject] CN=internal-server.company.com, OU=Servers, OU=Devices, O=org [Issuer] CN=SubCA02, OU=CA, o=org [Serial Number] 407ABCDE [Not Before] 31/10/2013 11:08:48 AM [Not After] 31/10/2016 11:08:48 AM [Thumbprint] 4354A34F6004F019E60F055979A47E50F62D1504 . System.Net Information: 0 : [5988] SecureChannel#23264094 – Cannot find the certificate in either the LocalMachine store or the CurrentUser store. I've validated the thumbprint, issuer and serial number listed in the log with the certificate in the LocalMachine store and these marry up. From what I can tell with much searching, this appears to be a permissions issue. The user the application is running as has been granted access to the private key (Personal Certificates - right click on the certificate - all tasks - Manage Private Keys), so I'm now at a loss as to which permission(s) it may be that is causing the issue.

    Read the article

  • ssh key error - Permission denied (publickey,gssapi-keyex,gssapi-with-mic)

    - by user1963938
    Amazon Ec2 :: Redhat 6. 64 Bit I'm trying to follow the socks5 guidelines (http://www.catonmat.net/blog/linux-socks5-proxy/ ) to open a socks on one of our servers but unfortunately I got suck at step 1 . ssh -N -D 0.0.0.0:1080 localhost I get error Permission denied (publickey,gssapi-keyex,gssapi-with-mic). How do I fix it ? More debug info ssh -v -f -N -D 0.0.0.0:1080 localhost OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to localhost [127.0.0.1] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type -1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_0' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_0' not found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug1: Trying private key: /root/.ssh/id_rsa debug1: Trying private key: /root/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey,gssapi-keyex,gssapi-with-mic).

    Read the article

  • Cannot reactivate RAID-5 volume: The size of the plex member is invalid

    - by Ian Boyd
    We had a 3-drive Windows Server 2008 R2 RAID-5 fail (operating in redundancy mode): WDC 1 TB WDC 1 TB WDC 1 TB We removed the failed hard drive, and put a WDC 1 TB drive (that we had standing by) into the machine. When launched, Disk Manager, asked permission to "initialize" the disk as either: Master Boot Record (MBR) Guid Partition Table (GPT) We initialized the disk as GPT, converted it to dynamic, and tried to use the Repair Volume command - except it was greyed out. (which is a terrifying thing on a failed production server hosting 3 virtual servers) i tried from the diskpart command line tool. First we look for our RAID-5 volume that is in Failed Rd mode: DISKPART> list volume Volume ### Ltr Label Fs Type Size Status Info ---------- --- ----------- ----- ---------- ------- --------- -------- Volume 0 E VMs (Raid5) NTFS RAID-5 1863 GB Failed Rd Volume 1 D DVD-ROM 0 B No Media Volume 2 System Rese NTFS Partition 100 MB Healthy System Volume 3 C NTFS Partition 1862 GB Healthy Boot There, Volume 0. Make that our active context: DISKPART> select volume 0 Volume 0 is the selected volume. Now we need to find the disk we will be repairing the volume with: DISKPART> list disk Disk ### Status Size Free Dyn Gpt -------- ------------- ------- ------- --- --- Disk 0 Online 931 GB 0 B * Disk 1 Online 931 GB 931 GB * Disk 2 Online 1863 GB 0 B Disk 3 Online 931 GB 0 B * Disk M0 Missing 0 B 0 B * The disk with 931 GB free, Disk 1. Now we just need to repair the volume: DISKPART> repair disk=1 Virtual Disk Service error: The size of the plex member is invalid.

    Read the article

  • Access to message queuing system is denied MSMQ?

    - by user1401694
    My problem is a little confusing. I have 2 servers (Windows Server 2008 R2) with MSMQ installed and I want to use Server B to consume a MessageQueue on Server A. When I try to Receive it always throws a message error: "Access to message queuing system is denied.". IP between them. Server A: 172.31.23.130 Server B: 172.31.23.195 FormatName:Direct=TCP:172.31.23.195\private$\queuesource (It's working for Sends) I can ping each server from the other; The firewall is disabled; The "queuesource" has Full Control to "Everyone", "Anonymous Logon", "Network", "Network Services"; Journal is disabled; Authentication is ok; The queue is Transactional. My code in .Net C# is basically like this: MessageQueue _sourceQueue = new MessageQueue(); _sourceQueue.Path = "FormatName:Direct=TCP:172.31.23.195\private$\queuesource"; _sourceQueue.Receive(); // << here throw an exception. Actually I'm using the Private Queue only to avoid Active Directory's problems. For example, if the server DNS fail all network fail. I don't know what do anymore.

    Read the article

  • Oracle VM repository creation seems contradictory to its server pool?

    - by Michael
    I found something contradictory in Oracle VM. Clustered server pool creation in Oracle VM would format my FC LUN as ocfs2 , and start o2cb & ocfs2 services to build cluster environment. After that, when I wanted to create repository on the serverpool, unexpectedly, it told me that the physical disk I chose which is also my FC LUN, already contains a file system. What a contradictory! So what, delete the file system in serverpool? If so, why created it before?! OVM> list physicaldisk Command: list physicaldisk Status: Success Time: 2012-09-10 06:44:42.660 Data: id:0004fb00001800007765e62381895f61 name:OVM_HDS OVM> create serverpool clusterenable=true virtualip=10.84.21.123 physicaldisk=OVM_HDS name=ovmserverpool Serverpool creation took quite a long time since my FC LUN was big. When the creation completed, my FC LUN was created as ocfs2 and o2cb & ocfs2 services were started on my ovm servers successfully. But then repository creation indeed throws me a big surprise ... OVM> create repository serverpool=ovmserverpool physicaldisk=OVM_HDS name=ovmrepo Command: create repository serverpool=ovmserverpool physicaldisk=OVM_HDS name=ovmrepo Status: Failure Time: 2012-09-10 06:23:44.656 Error Msg: com.oracle.ovm.mgr.api.exception.RuleException: OVMRU_002026E Cannot use or delete physical disk: OVM_HDS, it already contains a file system: [Pool filesystem for ovmserverpool] Mon Sep 10 06:23:44 CST 2012 What should I do now? Delete the filesystem using dd command? That would destroy the serverpool, right? I'm really confused. My OVM Manager version is 3.1.1.399 which is the latest. Any tips are appreciated. Thanks.

    Read the article

  • Port forwarding on Fortigate 50B

    - by sindre j
    I have serious problems setting up port forwarding on a Fortigate 50B. The unit is basically running as factory default, the wan1 interface is connected to my fibre optic internet modem, and my lan is connected to the internal switch of the Fortigate. The factory default firewall policy allowing traffic from the internal interface to wan1 is kept and I'm able to access the interet as normal. Then I added a virtual ip and a firewall policy for allowing access from the internet to my local servers (ip 192.168.9.51) webserver (standard port 80). The settings I made are as follows. Edit Virtual IP Mapping Name : Server VIP External interface : wan1 Type : Static NAT Extermal IP Address/Range : 0.0.0.0 Mapped IP Address/Range : 192.168.9.51 Port Forwading : not checked Firewall policy Source interface/Zone : wan1 Source address : all Destination interface/Zone : internal Destination address : Server VIP Schedule : always Service : HTTP Action : ACCEPT no other settings checked What happens now is that I'm unable to access internet from my server, I'm not getting through to the webserver from internet either. I'm able to ping a site on the outside, but all web traffic is blocked, both ways. I've checked the documentation, but as far as I can tell I have set this up correctly. Anyone here with knowledge of Fortigate port forwading/NAT?

    Read the article

  • WmiPrvSE memory leak on Windows 2008 *R2*

    - by MichaelGG
    I've seen references on Windows 2008 to WmiPrvSE leaks, but nothing about Windows 2008 R2. We're running R2 on top of Hyper-V (2008). We are also running NSClient++ for monitoring from opsview. Over time, WmiPrvSE.exe starts to use a lot of memory, causing memory alert issues (less than 10% free). VM has 2GB, WmiPrvSE consumes up to 500-600MB before I kill it. Killing the process doesn't seem to have any negative effect; it starts up again and I haven't noticed any problems. But after a day or two, it's back in the same situation. Any ideas on what to do? Resource Monitor doesn't show any Disk or Network IO by WmiPrvSE.exe. Just slowly climbing private memory... Edited to add: We aren't running clustering, or Windows System Resource Manager. The only regular WMI user I can guess is NSClient++, but we don't seem to have this problem on other servers.

    Read the article

  • Are VMWare ESXi 5 patches cumulative?

    - by ewwhite
    It seems basic, but there's confusion about the patching strategy needed to manually update standalone VMWare ESXi hosts. The VMWare vSphere blog attempts to explain this, but it's still not clear. From the blog: Say Patch01 includes updates for the following VIBs: "esxi-base", "driver10" and "driver 44". And then later Patch02 comes out with updates to "esxi-base", "driver20" and "driver 44". P2 is cumulative in that the "esxi-base" and "driver44" VIBs will include the updates in Patch01. However, it's important to note that Patch02 not include the "driver 10" VIB as that module was not updated. Many of my ESXi installations are standalone and do not make use of Update Manager. It is possible to update an individual host using the patches make available through the VMWare patch download portal. The process is quite simple, and that part makes sense. The bigger issue is determining what to actually download and install. In my case, I have a good number of HP-specific ESXi builds that incorporate sensors and management for HP ProLiant hardware. Let's say that those servers start at ESXi build #474610 from 9/2011. Looking at the patch portal screenshot below, there is a patch for ESXi update01, build #623860. There are also patches for builds #653509 and #702118. Coming from the old version of ESXi, what is the proper approach to bring the system fully up-to-date? Which patches are cumulative and which need to be applied sequentially? Perhaps the download size is the confusing factor, but is installing the newest build the right approach, or do I need to step back and patch incrementally?

    Read the article

  • Windows 7 intermittently drops wired internet/lan connection.

    - by CraigTP
    In a nutshell, my Windows 7 Ultimate PC intermittently drops it's internet connection. Why? Background: My PC is wired to my ADSL modem/router which is directly connected to the phone line. I also have wireless connectivity turned on within the router for a laptop to connect wirelessly. Every few hours or so, when using my PC, I find I cannot access the internet and pages will not load. Eventually, Windows7 will update the network icon in the task-tray to show the exclamation mark symbol on the network icon. Opening up the Network And Sharing Centre will show the red cross between the "Multiple Networks" and "The Internet". Here's a picture of the "Network And Sharing Centre" (grabbed when everything was working!) As you can see, I'm running Sun's VirtualBox on this machine and that creates a Network connection for itself. This doesn't seem to affect the intermittent dropping (i.e. the intermittent drops occur whether the VirtualBox connection is in use or not). When the connection does drop, I cannot access any internet pages, nor can I access the router's web admin page at http://192.168.1.1/, so I'm assuming I've lost all local LAN access too. It's definitely not the router (or the internet connection itself) as my laptop, using the wireless connection (and running Vista Home Premium) continues to be able to access the internet (and the router's web admin pages) just fine. Every time this happens, I can immediately restore all internet and LAN access by opening Network Adapter page, disabling the "Local Area Connection" and then re-enabling it. Give it a few seconds and everything is fine again. I assume this is because, beneath the GUI, it's effectively doing an "ipconfig /release" then "ipconfig /renew". Why does this happen in the first place, though? I've googled for this and seen quite a few other people (even on MSDN/Technet forums) experiencing the same or almost the same problem, but with no clear resolution. Suggestions of turning off IPv6 on the LAN adapter, and ensuring there's no power management "sleeping" the network adapter have been tried but do not cure the problem. There does not seem to be any particular sequence of events that cause it to happen either. I've had it go twice in 20 minutes when just randomly browsing the web with no other traffic, and I've also had it go once then not go again for 2-3 hours with the same sort of usage. Can anyone tell me why this is happening and how to make it stop? EDIT: Additional information based upon the answer provided so far: Firstly, I forgot the mention that this is Windows 7 64 bit if that makes any difference at all. I mentioned that I don't think the VirtualBox network adpater is causing this problem in any way, and I also have VirtualBox installed on two other machines, one running Vista Home Premium and the other running XP. Neither of these machine experience the same network connectivity issues as the Windows 7 machine. The IP assignment for the Windows 7 machine is the same both before and after the "drop". I have a DHCP server on the router issuing IP Addresses, however my Windows 7 machine uses a static address. Here's the output from "ipconfig": Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Within the system's event logs, the only event that relates to the connection dropping is a "DNS Client Event" and this is generated after the connection has dropped and is an event detailing that DNS information can't be found for whatever website I may be trying to access, just as the connection drops: Log Name: System Source: Microsoft-Windows-DNS-Client Event ID: 1014 Task Category: None Level: Warning Keywords: User: NETWORK SERVICE Description: Name resolution for the name weather.service.msn.com timed out after none of the configured DNS servers responded. The network adapter chipset is Realtek PCIe GBE Family Controller and I have confirmed that this is the correct chipset for the motherboard (Asus M4A77TD PRO), and in fact, Windows Update installed an updated driver for this on 12/Jan/2009. The details of the update say that it's a Realtek software update from December 2009. Incidentally, I was still having the same intermittent problems prior to this update. It seems to have made no difference at all. EDIT 2 (1 Feb 2010): In my quest to solve this problem, I have discovered some more interesting information. On another forum, someone suggested that I should try running Windows in "Safe Mode With Networking" and see if the problem continues to occur. This was a fantastic suggestion and I don't know why I didn't think of it sooner myself. So, I proceeded to run in Safe Mode with Networking for a number of hours, and amazingly, the "drops" didn't occur once. It was a positive discovery, however, due to the intermittent nature of the original problem, I wasn't completely convinced that the problem was cured. One thing I did note is that the fan on my GFX card was running alot louder than normal. This is due to the fact that I have an ASUS ENGTS250 graphics card (http://www.asus.com/product.aspx?P_ID=B6imcoax3MRY42f3) which had a known problem with a noisy fan until a BIOS update fixed the issue. (See the "Manufacturer Response" here: http://www.newegg.com/Product/Product.aspx?Item=N82E16814121334 for details). Well, running in safe mode had the fan running (incorrectly) at full speed (as it did before the BIOS update), but with an (apparently) stable network connection. Obviously some driver was not loaded for the GFX card when in Safe Mode so this got me thinking about the GFX card (since the very noisy fan was quite obvious when running in Safe Mode). I rebooted into normal mode, and found that Nvidia had a very up-to-date new driver for my GFX card (only about 1 week old), so I downloaded the appropriate driver and installed it. After installation and a reboot, I was able to use my PC for an entire day with NO NETWORK DROPS!!! This was on Saturday. However, on the Sunday, I also had my PC for pretty much the entire day and experienced 2 network drops. No other changes have been made to my PC in this time. So, the story seems to be that updating my graphics card drivers seems to have improved (if not completely fixed) the issue, however, I'm still searching for a proper fix for this problem. Hopefully, this information may help anyone who may have additional ideas as to why this problem is occuring in the first place. (And why does new GFX card drivers have anything to do with the network?) I appreciate everyone's feedback so far. However, I'll have to ask once more if anyone has any further ideas of how to fix this particular problem? Thanks in advance.

    Read the article

  • Replication of lockoutTime attribute is not urgent on AD-LDS

    - by ixe013
    I have two LDS servers on the same subnet. They replicate well. If I change an attribute, it gets replicated after 15 seconds. LDS is configured to honor password policies. When a user makes too many wrong password attemps, his account is locked and that user's lockoutTime attribute is set accordingly. But lockoutTime is not replicated as urgent. In fact, it is not replicated unless there is another change somewhere in the directory. The lockoutTime attribute will be replicated. Here is an (edited Wireshark) trace. It shows normal replication trafic No. Time Protocol Length Info 133 16:23:02 DRSUAPI 562 DsGetNCChanges request 134 16:23:02 DRSUAPI 3042 DsGetNCChanges response 152 16:23:17 DRSUAPI 562 DsGetNCChanges request 157 16:23:17 DRSUAPI 242 DsGetNCChanges response 230 16:24:57 DRSUAPI 562 DsGetNCChanges request 231 16:24:57 DRSUAPI 2930 DsGetNCChanges response 246 16:25:12 DRSUAPI 562 DsGetNCChanges request Right after that, I lock the user (with a FOR loop and ldifde). Nothing happens, until I give up and change the description attribute on the user, then about 15 seconds later I see the replication go through. 1984 16:31:05 DRSUAPI 562 DsGetNCChanges request 1985 16:31:05 DRSUAPI 2930 DsGetNCChanges response The lockoutTime and description is replicated. As stated here, if I set lockoutTime to 0, replication occurs after 15 seconds ! I have enabled replication diagnostics, but nothing shows up in the instance's logs - strange. I have enabled change notification between sites, restarted both services, but I did not see any changes. How can I make the lockoutTime replication urgent ?

    Read the article

  • SQL Server 2008 Cluster Installation - First network name always fails

    - by boflynn
    I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

    Read the article

  • Office365 SPF record has too many lookups

    - by Sammitch
    For some utterly ridiculous administrative reasons we've got a split domain with one mailbox on Office365 which requires us to add include:outlook.com to our SPF record. The problem with this is that that rule alone requires nine DNS lookups of the maximum of 10. Seriously, it's horrible. Just look at it: v=spf1 include:spf-a.outlook.com include:spf-b.outlook.com ip4:157.55.9.128/25 include:spfa.bigfish.com include:spfb.bigfish.com include:spfc.bigfish.com include:spf-a.hotmail.com include:_spf-ssg-b.microsoft.com include:_spf-ssg-c.microsoft.com ~all Given that we have our own large-ish mail system we need to have rules for a, mx, include:_spf1.mydomain.com, and include:_spf2.mydomain.com which puts us at 13 DNS lookups which causes PERMERRORs with strict SPF validators, and completely unreliable/unpredictable validation with non-strict/badly implemented validators. Is it possible to somehow eliminate 3 of those include: rules from the bloated outlook.com record, but still cover the servers used by O365? Edit: Commentors have mentioned that we should simply use the shorter spf.protection.outlook.com record. While that is news to me, and it is shorter, it's only one record shorter: spf.protection.outlook.com include:spf-a.outlook.com include:spf-b.outlook.com include:spf-c.outlook.com include:spf.messaging.microsoft.com include:spfa.frontbridge.com include:spfb.frontbridge.com include:spfc.frontbridge.com Edit² I suppose we can technically pare this down to: v=spf1 a mx include:_spf1.mydomain.com include:_spf2.mydomain.com include:spf-a.outlook.com include:spf-b.outlook.com include:spf-c.outlook.com include:spfa.frontbridge.com include:spfb.frontbridge.com include:spfc.frontbridge.com ~all but the potential issues I see with this are: We need to keep abreast of any changes to the parent spf.protection.outlook.com and spf.messaging.microsoft.com records. If anything is changed or [god forbid] added we would have to manually update ours to reflect that. With our actual domain name the record's length is 260 chars, which would require 2 strings for the TXT record, and I honestly don't trust that all of the DNS clients and SPF resolvers out there will properly accept a TXT record longer than 255 bytes.

    Read the article

  • DNS Server address configured inside Router not working

    - by Charandeep Singh
    Well, I have an ISP router in which I have configured DNS Servers to use (Primary & Secondary) like Google DNS. It works just fine. But now I have setup a computer with DNS server (Simple DNS Plus). I got it working by settings my internal DNS Server IP Address in computer. i.e. 192.168.1.3 So, instead of settings my internal DNS IP Address in every computer in my network, I want to setup DNS Server into my router. So on every DHCP request, computer get DNS Server to use. So I configured it like this: Primary DNS: 192.168.1.3 Secondry DNS: (left blank) After applying and DNS Requests stop resolving. But strange part is DNS request does goes to DNS Server but maybe not returned back, because all DNS request were available in cache logs. I don't know why this is not working, let me know if you have any solution or wordaround for this. Thanks! Update 1: NSLOOKUP Result C:\Users\user>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out

    Read the article

  • error reading keytab file krb5.keytab

    - by Banjer
    I've noticed these kerberos keytab error messages on both SLES 11.2 and CentOS 6.3: sshd[31442]: pam_krb5[31442]: error reading keytab 'FILE: / etc/ krb5. keytab' /etc/krb5.keytab does not exist on our hosts, and from what I understand of the keytab file, we don't need it. Per this kerberos keytab introduction: A keytab is a file containing pairs of Kerberos principals and encrypted keys (these are derived from the Kerberos password). You can use this file to log into Kerberos without being prompted for a password. The most common personal use of keytab files is to allow scripts to authenticate to Kerberos without human interaction, or store a password in a plaintext file. This sounds like something we do not need and is perhaps better security-wise to not have it. How can I keep this error from popping up in our system logs? Here is my krb5.conf if its useful: banjer@myhost:~> cat /etc/krb5.conf # This file managed by Puppet # [libdefaults] default_tkt_enctypes = RC4-HMAC DES-CBC-MD5 DES-CBC-CRC default_tgs_enctypes = RC4-HMAC DES-CBC-MD5 DES-CBC-CRC preferred_enctypes = RC4-HMAC DES-CBC-MD5 DES-CBC-CRC default_realm = FOO.EXAMPLE.COM dns_lookup_kdc = true clockskew = 300 [logging] default = SYSLOG:NOTICE:DAEMON kdc = FILE:/var/log/kdc.log kadmind = FILE:/var/log/kadmind.log [appdefaults] pam = { ticket_lifetime = 1d renew_lifetime = 1d forwardable = true proxiable = false retain_after_close = false minimum_uid = 0 debug = false banner = "Enter your current" } Let me know if you need to see any other configs. Thanks. EDIT This message shows up in /var/log/secure whenever a non-root user logs in via SSH or the console. It seems to only occur with password-based authentication. If I do a key-based ssh to a server, I don't see the error. If I log in with root, I do not see the error. Our Linux servers authenticate against Active Directory, so its a hearty mix of PAM, samba, kerberos, and winbind that is used to authenticate a user.

    Read the article

  • Cisco: Site-to-site VPN with cisco 878 and ASA weirdness

    - by cpf
    I currently have 2 sites, both connected to each other through 2 firewalls / routers in a site-to-site VPN. Pinging from server to server (Using 2mb/2mb SDSL) through that VPN obviously works, however, at one site, we have another internet connection (7m/400k ADSL), and only the link between the two sites should be on the other connection. All pc's should go over the other connection for internet, just communication between servers & Communication between pc's and the server at the other side should go through there too. What is configured at the moment is the server is using the SDSL directly as default gateway. Since it's not intended to surf anything it is a safe config. PC's are configured on the ADSL as default gateway. Now I wanted to route through everything that uses the range used on the other site, it should be sent from the ADSL modem to the SDSL modem, which has the VPN connection. I figured I could use OSPF to do so, however, OSPF doesn't seem to "detect" the range of the external site. Also (due to bad ip subnetting thanks to the other administrator), the ip used internally as the server on the other site also exists on the internet (causing a lot of confusion), so rdp-ing from our server to the server of the other site works (somehow), but tracerouting on the SDSL router (which should actually, in my opinion, go over the VPN) actually goes all over the internet. My question(s): Why doesn't the SDSL router ping the external ip through VPN, but the server does? Why can't I route from the ADSL router to the SDSL over VPN? I would seriously appreciate some help, since I can't figure out why it does it like this.

    Read the article

  • Word 2007 crashes on Server 2008 R2 terminal services

    - by John Rennie
    We are finding that Word 2007 (with SP2) crashes when used on a Windows 2008 R2 terminal server. Typically it crashes when you click File/Open or File/Save, but not every time. Maybe one time in four, and just to be really confusing, on a test server in my office I can't make it crash. I have just today set up a brand new shiny 2k8 R2 terminal server with as simple a setup as possible, e.g. no anti-virus to confuse things, and we're still seeing crashes. My question is has anyone else seen this, and if so any clues on what's happening? We have a support case open with Microsoft, and the MS support engineer has conceded it's happening, but has so far been unable to find the reason. On possible factor is that all the 2k8 R2 terminal servers I've seen this on have been Hyper-V VMs (running on a 2k8 R2 host). I'm about to put in a physical 2k8 R2 terminal server at the customer where we're seeing the most crashes, in case this is relevant. More news soon. Sorry if this posting seems a bit vague, but this has just bitten us and is causing a lot of pain and sleepless nights :-( If anyone can help I'll be enormously grateful! Update: we've given up and gone back to 2008 pre-R2. Both Office 2003 and 2007 both work fine now. I think there are some problems with TS in R2. Googling doesn't find much, so I thought it was just me. It's reassuring to find that someone else has seen the same problem.

    Read the article

  • ADODB DB2 DSN using IBMDADB2 provider

    - by Eli Sand
    I have a very bizarre issue with trying to establish a working connection to an IBM DB2 server from Classic ASP using ADODB. On my development server I am running IIS and have a local instance of DB2 running. When I create a system DSN on this server and try to connect to it with ADODB, I have to specify Provider=IBMDADB2; in my connection along with the DSN name - failure to include the provider and my connection won't work. On my production server(s), I have one running IIS and a second system running an instance of DB2. When I create a system DSN on the production IIS server and try to connect to it with ADODB, I cannot specify the provider, otherwise it throws an uncatchable error in an external module (I assume it's referring to the DB2 module) if I try to do anything past get a connection (oddly, opening the connection itself doesn't throw an error - but if I run a query it does). If I remove the Provider=IBMDADB2; from the connection string (thus I just have DSN=some_name), it works fine. On both systems I can verify through the ODBC connection manager that the DSN's work and can connect to the databases, and on both systems I have made sure to set the correct (only) instance of DB2 as the default. Can anyone tell me why I have to have different connection strings for the development and production servers? I would like to be able to use the same connection string for both environments if at all possible. If that means either specifying a provider for both, or for neither I don't care which - I would just like to know what's going on and how to fix it.

    Read the article

< Previous Page | 394 395 396 397 398 399 400 401 402 403 404 405  | Next Page >