Search Results

Search found 4979 results on 200 pages for 'django fan'.

Page 4/200 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Notebook MSI GT640 - noisy fan - Ubuntu 11.10 x64

    - by pablo
    I have all time this issue when using Ubuntus, the fan (fans?) runs most off the time and between 60%~100% even in idle which is weird. The GPU temperatures are mostly around 80 degrees and I don't think it's right :( I always use Jupiter with power saving preset and add the line in linux default like this: quiet splash pcie_aspm=force i915.i915_enable_rc6=1 So it helps a little (fan just doesn't run all the time 100%...) What else can I do? The notebook spec is: Core i7-720 (8 threads) NVIDIA GTS250M So it's rather one of the first, not so silent and cold notebooks;), with Core i7 family and without optimus technology (as nvidia GPU is the only graphic card built-in) but anyway I don't have theese strange hot times in Windows 7.

    Read the article

  • How to stop fan running always on Asus P8P76LE motherboard with ATI Radeon HD6900

    - by Chris Good
    I'm using Ubuntu 12.04 LTS. I'm not sure if it is the CPU (i7) fan or the video card fan. I've tried using lm-sensors & fancontrol sudo sensors-detect Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `w83627ehf': * ISA bus, address 0x290 Chip `Nuvoton NCT6776F Super IO Sensors' (confidence: 9) Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: # Chip drivers coretemp w83627ehf Like many people, I'm also getting error: /usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed Here is the output of sensors: # sensors radeon-pci-0100 Adapter: PCI adapter temp1: +71.0°C coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +44.0°C (high = +80.0°C, crit = +98.0°C) Core 0: +44.0°C (high = +80.0°C, crit = +98.0°C) Core 1: +40.0°C (high = +80.0°C, crit = +98.0°C) Core 2: +43.0°C (high = +80.0°C, crit = +98.0°C) Core 3: +42.0°C (high = +80.0°C, crit = +98.0°C) I'm hoping some-one has already solved this for my configuration because this seems to be a problem for many people and there are many different suggestions.

    Read the article

  • How to stop fan running always on Asus P8P67LE motherboard with ATI Radeon HD6900

    - by Chris Good
    I'm using Ubuntu 12.04 LTS. I'm not sure if it is the CPU (i7) fan or the video card fan. I've tried using lm-sensors & fancontrol sudo sensors-detect Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `w83627ehf': * ISA bus, address 0x290 Chip `Nuvoton NCT6776F Super IO Sensors' (confidence: 9) Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: # Chip drivers coretemp w83627ehf Like many people, I'm also getting error: /usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed Here is the output of sensors: # sensors radeon-pci-0100 Adapter: PCI adapter temp1: +71.0°C coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +44.0°C (high = +80.0°C, crit = +98.0°C) Core 0: +44.0°C (high = +80.0°C, crit = +98.0°C) Core 1: +40.0°C (high = +80.0°C, crit = +98.0°C) Core 2: +43.0°C (high = +80.0°C, crit = +98.0°C) Core 3: +42.0°C (high = +80.0°C, crit = +98.0°C) I'm hoping some-one has already solved this for my configuration because this seems to be a problem for many people and there are many different suggestions.

    Read the article

  • Fan speeds up and slows down annoyingly on a Dell Latitude 5520

    - by user38175
    I' ve just bought a dell latitude 5520 and installed 11.10, my trouble is that the fan is noisy which is not regular. It is quiet for 1 minute and then speeds up and slows down every 4 seconds for 1 minute : it's very annoying. I tried i8fan things on the Internet but i didn't solve my problem, it seems to work better in windows 7 but i don't use it a lot. Dell technician came and changed the motherboard and the fan but it's still the same. I have to put music on when i'm on my computer... Anyone have the same problem or a solution?

    Read the article

  • Fan not detected by lm-sensors

    - by OrangeTux
    My fan is blowing hard, while my cpu temperature is 32 degrees I tried a lot of things to control my fan. Changed grub file GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi= pci=noacpi" _ GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=\"Linux\"" Ran sensors-detect : To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO) Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK Ran sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +34.0°C (crit = +90.0°C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +34.0°C (high = +80.0°C, crit = +90.0°C) Core 2: +34.0°C (high = +80.0°C, crit = +90.0°C) Ran sudo start module-init-tools and sudo start module-init-tools module-init-tools stop/waiting As you can see my fan isn't detected. Running fancontrol gives me this: Loading configuration from /etc/fancontrol ... Error: Can't read configuration file Can you help me, please? I cannot use my laptop now in class. Thanks in advance. My system 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5400 Series] 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05)

    Read the article

  • Fan very loud in Ubuntu 12.10

    - by Jon
    I recently installed 12.10 on my Desktop PC, moving away from Windows 7. For some reason, the fan in my computer is making an enormous amount of noise (it is running at full speed constantly). Under Windows 7, the fan would slow itself down and run at an acceptable noise level. Now, it is nearly unbearable. Checked the processes, and none are taking up a huge load on the CPU. Please help as I really can't endure this noise, and I do not want to go back to Windows 7 on this box. Some specs: - Intel 2.26 duo core - ATI 4870 - 4GB - 650W power supply

    Read the article

  • Problem with messages framework in Django 1.2

    - by Konstantin
    Hello! I'm running Django 1.2 beta and trying out the new feature: message framework. http://docs.djangoproject.com/en/dev/ref/contrib/messages/ Everything seems to work, but when I try to output the messages, I get nothing. Seems that messages variable is empty. I double checked all the settings, they seem to be just like in the manual. What could be wrong? settings.py MIDDLEWARE_CLASSES = ( 'django.middleware.common.CommonMiddleware', 'django.contrib.sessions.middleware.SessionMiddleware', 'django.contrib.messages.middleware.MessageMiddleware', #send messages to users 'django.middleware.locale.LocaleMiddleware', 'django.contrib.auth.middleware.AuthenticationMiddleware', #debug tool 'debug_toolbar.middleware.DebugToolbarMiddleware', ) TEMPLATE_CONTEXT_PROCESSORS = ( 'django.contrib.messages.context_processors.messages', #send messages to users 'django.core.context_processors.auth', ) #Store messages in sessions MESSAGE_STORAGE = 'django.contrib.messages.storage.session.SessionStorage'; INSTALLED_APPS = ( 'django.contrib.auth', 'django.contrib.contenttypes', 'django.contrib.sessions', #'django.contrib.sites', 'django.contrib.admin', 'django.contrib.messages', 'debug_toolbar', #my apps #... ) views.py def myview(request): from django.contrib import messages messages.error(request, 'error test'); messages.success(request, 'success test'); return render_to_response('mytemplate.html', locals()); mytemplate.html {% for message in messages %} {{ message }}<br /> {% endfor %} In template nothing is outputted.

    Read the article

  • Django 1.4.1 error loading MySQLdb module when attempting 'python manage.py shell'

    - by Paul
    I am trying to set up MySQL, and can't seem to be able to enter the Django manage.py shell interpreter. Getting the output below: rrdhcp-10-32-44-126:django pavelfage$ python manage.py shell Traceback (most recent call last): File "manage.py", line 10, in <module> execute_from_command_line(sys.argv) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/core/management/__init__.py", line 443, in execute_from_command_line utility.execute() File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/core/management/__init__.py", line 382, in execute self.fetch_command(subcommand).run_from_argv(self.argv) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/core/management/base.py", line 196, in run_from_argv self.execute(*args, **options.__dict__) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/core/management/base.py", line 232, in execute output = self.handle(*args, **options) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/core/management/base.py", line 371, in handle return self.handle_noargs(**options) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/core/management/commands/shell.py", line 45, in handle_noargs from django.db.models.loading import get_models File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/db/__init__.py", line 40, in <module> backend = load_backend(connection.settings_dict['ENGINE']) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/db/__init__.py", line 34, in __getattr__ return getattr(connections[DEFAULT_DB_ALIAS], item) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/db/utils.py", line 92, in __getitem__ backend = load_backend(db['ENGINE']) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/db/utils.py", line 24, in load_backend return import_module('.base', backend_name) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/utils/importlib.py", line 35, in import_module __import__(name) File "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/django/db/backends/mysql/base.py", line 16, in <module> raise ImproperlyConfigured("Error loading MySQLdb module: %s" % e) django.core.exceptions.ImproperlyConfigured: Error loading MySQLdb module: No module named _mysql Any suggestions really appreciated.

    Read the article

  • How to resolve user registration and activation email error in Django registration?

    - by user2476295
    So I was just trying to setup a basic user authentication in Django and downloaded a django registration app with templates. Now when I run the server at 127.0.0.1:8000/accounts/register/ I get a basic registration page, I fill in the details and when I click submit I get this error "NoReverseMatch at /accounts/register/" Error during template rendering In template Users/sudhasinha/mysite/mysite/registration/templates/registration/activation_email.txt, error at line 4 'url' requires a non-empty first argument. The syntax changed in Django 1.5, see the docs. 1 {% load i18n %} 2 {% trans "Activate account at" %} {{ site.name }}: 3 4 http://{{ site.domain }}{**% url registration_activate activation_key %**} 5 6 {% blocktrans %}Link is valid for {{ expiration_days }} days.{% endblocktrans %} 7 This is what my activation_email.txt looks like: {% load i18n %} {% trans "Activate account at" %} {{ site.name }}: http://{{ site.domain }}{% url registration_activate activation_key %} {% blocktrans %}Link is valid for {{ expiration_days }} days.{% endblocktrans %} And this is what my registration_form.html looks like: {% extends "base.html" %} {% load i18n %} {% block content %} <form method="post" action="."> {{ form.as_p }} <input type="submit" value="{% trans 'Submit' %}" /> </form> {% endblock %} I have very minimal experience with Django and would appreciate some help to resolve this error. My urls seem to be setup correctly but I will post it if needed. Also pardon my horrible formatting

    Read the article

  • Can Django admin handle a one-to-many relationship via related_name?

    - by Mat
    The Django admin happily supports many-to-one and many-to-many relationships through an HTML <SELECT> form field, allowing selection of one or many options respectively. There's even a nice Javascript filter_horizontal widget to help. I'm trying to do the same from the one-to-many side through related_name. I don't see how it's much different from many-to-many as far as displaying it in the form is concerned, I just need a multi-select SELECT list. But I cannot simply add the related_name value to my ModelAdmin-derived field list. Does Django support one-to-many fields in this way? My Django model something like this (contrived to simplify the example): class Person(models.Model): ... manager = models.ForeignKey('self', related_name='staff', null=True, blank=True, ) From the Person admin page, I can easily get a <SELECT> list showing all possible staff to choose this person's manager from. I also want to display a multiple-selection <SELECT> list of all the manager's staff. I don't want to use inlines, as I don't want to edit the subordinates details; I do want to be able to add/remove people from the list. (I'm trying to use django-ajax-selects to replace the SELECT widget, but that's by-the-by.)

    Read the article

  • Django - no module named app

    - by Koran
    Hi, I have been trying to get an application written in django working - but it is not working at all. I have been working on for some time too - and it is working on dev-server perfectly. But I am unable to put in the production env (apahce). My project name is apstat and the app name is basic. I try to access it as following Blockquote http://hostname/apstat But it shows the following error: MOD_PYTHON ERROR ProcessId: 6002 Interpreter: 'domU-12-31-39-06-DD-F4.compute-1.internal' ServerName: 'domU-12-31-39-06-DD-F4.compute-1.internal' DocumentRoot: '/home/ubuntu/server/' URI: '/apstat/' Location: '/apstat' Directory: None Filename: '/home/ubuntu/server/apstat/' PathInfo: '' Phase: 'PythonHandler' Handler: 'django.core.handlers.modpython' Traceback (most recent call last): File "/usr/lib/python2.6/dist-packages/mod_python/importer.py", line 1537, in HandlerDispatch default=default_handler, arg=req, silent=hlist.silent) File "/usr/lib/python2.6/dist-packages/mod_python/importer.py", line 1229, in _process_target result = _execute_target(config, req, object, arg) File "/usr/lib/python2.6/dist-packages/mod_python/importer.py", line 1128, in _execute_target result = object(arg) File "/usr/lib/pymodules/python2.6/django/core/handlers/modpython.py", line 228, in handler return ModPythonHandler()(req) File "/usr/lib/pymodules/python2.6/django/core/handlers/modpython.py", line 201, in __call__ response = self.get_response(request) File "/usr/lib/pymodules/python2.6/django/core/handlers/base.py", line 134, in get_response return self.handle_uncaught_exception(request, resolver, exc_info) File "/usr/lib/pymodules/python2.6/django/core/handlers/base.py", line 154, in handle_uncaught_exception return debug.technical_500_response(request, *exc_info) File "/usr/lib/pymodules/python2.6/django/views/debug.py", line 40, in technical_500_response html = reporter.get_traceback_html() File "/usr/lib/pymodules/python2.6/django/views/debug.py", line 114, in get_traceback_html return t.render(c) File "/usr/lib/pymodules/python2.6/django/template/__init__.py", line 178, in render return self.nodelist.render(context) File "/usr/lib/pymodules/python2.6/django/template/__init__.py", line 779, in render bits.append(self.render_node(node, context)) File "/usr/lib/pymodules/python2.6/django/template/debug.py", line 81, in render_node raise wrapped TemplateSyntaxError: Caught an exception while rendering: No module named basic Original Traceback (most recent call last): File "/usr/lib/pymodules/python2.6/django/template/debug.py", line 71, in render_node result = node.render(context) File "/usr/lib/pymodules/python2.6/django/template/debug.py", line 87, in render output = force_unicode(self.filter_expression.resolve(context)) File "/usr/lib/pymodules/python2.6/django/template/__init__.py", line 572, in resolve new_obj = func(obj, *arg_vals) File "/usr/lib/pymodules/python2.6/django/template/defaultfilters.py", line 687, in date return format(value, arg) File "/usr/lib/pymodules/python2.6/django/utils/dateformat.py", line 269, in format return df.format(format_string) File "/usr/lib/pymodules/python2.6/django/utils/dateformat.py", line 30, in format pieces.append(force_unicode(getattr(self, piece)())) File "/usr/lib/pymodules/python2.6/django/utils/dateformat.py", line 175, in r return self.format('D, j M Y H:i:s O') File "/usr/lib/pymodules/python2.6/django/utils/dateformat.py", line 30, in format pieces.append(force_unicode(getattr(self, piece)())) File "/usr/lib/pymodules/python2.6/django/utils/encoding.py", line 71, in force_unicode s = unicode(s) File "/usr/lib/pymodules/python2.6/django/utils/functional.py", line 201, in __unicode_cast return self.__func(*self.__args, **self.__kw) File "/usr/lib/pymodules/python2.6/django/utils/translation/__init__.py", line 62, in ugettext return real_ugettext(message) File "/usr/lib/pymodules/python2.6/django/utils/translation/trans_real.py", line 286, in ugettext return do_translate(message, 'ugettext') File "/usr/lib/pymodules/python2.6/django/utils/translation/trans_real.py", line 276, in do_translate _default = translation(settings.LANGUAGE_CODE) File "/usr/lib/pymodules/python2.6/django/utils/translation/trans_real.py", line 194, in translation default_translation = _fetch(settings.LANGUAGE_CODE) File "/usr/lib/pymodules/python2.6/django/utils/translation/trans_real.py", line 180, in _fetch app = import_module(appname) File "/usr/lib/pymodules/python2.6/django/utils/importlib.py", line 35, in import_module __import__(name) ImportError: No module named basic My settings.py is as follows: INSTALLED_APPS = ( 'django.contrib.auth', 'django.contrib.contenttypes', 'django.contrib.sessions', 'django.contrib.sites', 'apstat.basic', 'django.contrib.admin', ) If I remove the apstat.basic, it goes through, but that is not a solution. Is it something I am doing in apache? My apache - settings are - <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /home/ubuntu/server/ <Directory /> Options None AllowOverride None </Directory> <Directory /home/ubuntu/server/apstat> AllowOverride None Order allow,deny allow from all </Directory> <Location "/apstat"> SetHandler python-program PythonHandler django.core.handlers.modpython SetEnv DJANGO_SETTINGS_MODULE apstat.settings PythonOption django.root /home/ubuntu/server/ PythonDebug On PythonPath "['/home/ubuntu/server/'] + sys.path" </Location> </VirtualHost> I have now sat for more than a day on this. If someone can help me out, it would be very nice.

    Read the article

  • Error after installing Django (supposed PATH or PYTHONPATH "error")

    - by illuminated
    Hi all, I guess this is a PATH/PYTHONPATH error, but my attempts failed so far to make django working. System is Ubuntu 10.04, 64bit: mx:~/webapps$ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=10.04 DISTRIB_CODENAME=lucid DISTRIB_DESCRIPTION="Ubuntu 10.04 LTS" Python version: 2.6.5: @mx:~/webapps$ python -V Python 2.6.5 When I run django-admin.py, the following happens: mx:~/webapps$ django-admin.py Traceback (most recent call last): File "/usr/local/bin/django-admin.py", line 2, in <module> from django.core import management ImportError: No module named django.core Similar when I import django in python shell: mx:~/webapps$ python Python 2.6.5 (r265:79063, Apr 16 2010, 13:09:56) [GCC 4.4.3] on linux2 Type "help", "copyright", "credits" or "license" for more information. >>> import django Traceback (most recent call last): File "<stdin>", line 1, in <module> ImportError: No module named django >>> quit() More details: mx:~/webapps$ python -c "from distutils.sysconfig import get_python_lib; print get_python_lib()" /usr/lib/python2.6/dist-packages Within python shell: Python 2.6.5 (r265:79063, Apr 16 2010, 13:09:56) [GCC 4.4.3] on linux2 Type "help", "copyright", "credits" or "license" for more information. >>> import sys >>> print sys.path ['', '/usr/lib/python2.6/dist-packages/django', '/usr/local/lib/python2.6/dist-packages/django/bin', '/usr/local/lib/python2.6/dist-packages/django', '/home/petra/webapps', '/usr/lib/python2.6', '/usr/lib/python2.6/plat-linux2', '/usr/lib/python2.6/lib-tk', '/usr/lib/python2.6/lib-old', '/usr/lib/python2.6/lib-dynload', '/usr/lib/python2.6/dist-packages', '/usr/lib/python2.6/dist-packages/PIL', '/usr/lib/pymodules/python2.6'] django-admin.py can be found here: mx:~/webapps$ locate django-admin.py ~/install/sources/Django-1.2.1/build/lib.linux-i686-2.6/django/bin/django-admin.py ~/install/sources/Django-1.2.1/build/scripts-2.6/django-admin.py ~/install/sources/Django-1.2.1/django/bin/django-admin.py /usr/local/bin/django-admin.py /usr/local/lib/python2.6/dist-packages/django/bin/django-admin.py /usr/local/lib/python2.6/dist-packages/django/bin/django-admin.pyc and in the end this doesn't help: export PYTHONPATH="/usr/lib/python2.6/dist-packages/django:$PYTHONPATH" nor this: export PYTHONPATH="/usr/local/lib/python2.6/dist-packages/django:$PYTHONPATH" How to solve this !? Thanks all in advance! :)

    Read the article

  • What does the fan speed sensor really report?

    - by T. Verron
    I have an overheating issue on my netbook (ASUS EeePC 1015PW), which I'm trying to troubleshoot. Using lm-sensors while overheating gave me this output : acpitz-virtual-0 Adapter: Virtual device temp1: +86.0°C (crit = +100.0°C) eeepc-isa-0000 Adapter: ISA adapter fan1: 4089 RPM coretemp-isa-0000 Adapter: ISA adapter Core 0: +82.0°C (crit = +100.0°C) Core 1: +80.0°C (crit = +100.0°C) But I can't hear the fan. So I enabled manual pwm controling and set the fan to full speed, and after a few minutes I got this output : acpitz-virtual-0 Adapter: Virtual device temp1: +65.0°C (crit = +100.0°C) eeepc-isa-0000 Adapter: ISA adapter fan1: 4016 RPM coretemp-isa-0000 Adapter: ISA adapter Core 0: +62.0°C (crit = +100.0°C) Core 1: +58.0°C (crit = +100.0°C) And this time I could hear the fan spinning. So there's quite obviously an issue with either fan control or fan monitoring. Hence the question : what kind of physical information does the fan sensor really report? Thank you PS. I should have added that the computer is a small, hard-to-disassemble netbook, so I can't and don't want to try experiments like "block the fan and see what the sensor reports".

    Read the article

  • Ubuntu CPU Fan at 2200 RPM and CPU top at 90°C

    - by T-Erra
    I have a problem with my CPU heat. I'm running Ubuntu 14.04 (64bit) and I have issues with the cooling. I know it might be a hardware issue, but I've checked, the fan is running and in my GUI I use the command "sensors" which shows me a RPM of 2200 and a CPU temperature of 60°C while I'm not running any software. This seems to be really mysterious. However, if I start my IDE (Eclipse), Firefox and Chromium at the same time, the CPU temp goes up to 75-90° Celsius. I doubt that this is common for a system with 16 GB RAM, an i7 Processor and an Intel water cooling system and I also never had some issues like this before when I was running Ubuntu 12.04 or 13.04. Fan Speed At 60°C it's at 1300 RPM, and after start up Eclipse and Firefox it's at approximately 2200 RPM and between 75°C - 90°C depending on how many windows and IDE's I've opened. If I use the "top" command, there are just few processes like Xorg or Compiz which are taking up to 10% CPU usage at maximum, during the time I'm not running any software. I have tried to upgrade the Linux kernel, where I failed. After upgrading, I wasn't able to boot anymore so I tried to remove the new kernel from the boot directory and updated my grub file to an old entry, which works fine now, but still with the temperature issue. My NVIDIA drivers is also up to date, which dropped some issues I had before with the CPU load. So it can't be a problem with the graphic card. How can I find out, where the problem is, or why my CPU gets that high temperatures, which I only should get while playing games with high end graphics and so on? Did anyone have some similar issues before?

    Read the article

  • Intel graphics driver installer, now the CPU fan is rarely quiet

    - by Space monkey
    I have an Optimus chipset: Intel HD 4000 (i7-3635QM CPU) Geforce 640m I don't care about the NVIDIA card, so I didn't try to install any proprietary drivers for it. So: I was having a choppy+high CPU experience with gnome-shell on Ubuntu 14.04. Only happened when I tried moving a window around quickly. I used the Intel graphics installer hoping that it will fix the problem. It did fix the problem, now there is no choppyness or high CPU when I move windows around. However, there is a new problem now: The fan is rarely quiet, doing barely anything at all will cause the fan to go into loud mode quickly. That happens despite the CPU usage being at just around 4%. This wasn't the case before installing Intel drivers. It would normally only do that if, for example, I'm installing packages or doing something that puts some stress on the CPU. I set all CPU cores to "powersave" using cpufreq-set, but nothing changed. Also on Windows, the fans are really quiet when I'm in powersave mode. I believe they completely shut off for most of the time. I remember the installer giving me a report at the end as to which packages it installed. Unfortunately, I didn't save the report and I don't know where it would have saved it if it did. Any ideas or similar experiences?

    Read the article

  • django internationalization doesn't work

    - by xRobot
    I have: created translation strings in the template and in the application view. run this command: django-admin.py makemessages -l it and the file it/LC_MESSAGES/django.po has been created run this command: django-admin.py compilemessages and I receive: processing file django.po in /home/jobber/Desktop/library/books/locale/it/LC_MESSAGES set the language code in settings.py: LANGUAGE_CODE = 'it-IT' but.... translation doesn't work !! I always see english text. Why ?

    Read the article

  • ** EDITED ** 'NoneType' object has no attribute 'day'

    - by Asinox
    Hi guy, i dont know where is my error, but Django 1.2.1 is give this error: 'NoneType' object has no attribute 'day' when i try to save form from the Administrator Area models.py from django.db import models from django.contrib.auth.models import User class Editorial(models.Model): titulo = models.CharField(max_length=250,help_text='Titulo del editorial') editorial = models.TextField(help_text='Editorial') slug = models.SlugField(unique_for_date='pub_date') autor = models.ForeignKey(User) pub_date = models.DateTimeField(auto_now_add=True) activa = models.BooleanField(verbose_name="Activa") enable_comments = models.BooleanField(verbose_name="Aceptar Comentarios",default=False) editorial_html = models.TextField(editable=False,blank=True) def __unicode__(self): return unicode(self.titulo) def get_absolute_url(self): return "/editorial/%s/%s/" % (self.pub_date.strftime("%Y/%b/%d").lower(), self.slug) class Meta: ordering=['-pub_date'] verbose_name_plural ='Editoriales' def save(self,force_insert=False, force_update=False): from markdown import markdown if self.editorial: self.editorial_html = markdown(self.editorial) super(Editorial,self).save(force_insert,force_update) i dont know why this error, COMPLETED ERROR: Traceback: File "C:\wamp\bin\Python26\lib\site-packages\django\core\handlers\base.py" in get_response 100. response = callback(request, *callback_args, **callback_kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\contrib\admin\options.py" in wrapper 239. return self.admin_site.admin_view(view)(*args, **kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\utils\decorators.py" in _wrapped_view 76. response = view_func(request, *args, **kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\views\decorators\cache.py" in _wrapped_view_func 69. response = view_func(request, *args, **kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\contrib\admin\sites.py" in inner 190. return view(request, *args, **kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\utils\decorators.py" in _wrapper 21. return decorator(bound_func)(*args, **kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\utils\decorators.py" in _wrapped_view 76. response = view_func(request, *args, **kwargs) File "C:\wamp\bin\Python26\lib\site-packages\django\utils\decorators.py" in bound_func 17. return func(self, *args2, **kwargs2) File "C:\wamp\bin\Python26\lib\site-packages\django\db\transaction.py" in _commit_on_success 299. res = func(*args, **kw) File "C:\wamp\bin\Python26\lib\site-packages\django\contrib\admin\options.py" in add_view 777. if form.is_valid(): File "C:\wamp\bin\Python26\lib\site-packages\django\forms\forms.py" in is_valid 121. return self.is_bound and not bool(self.errors) File "C:\wamp\bin\Python26\lib\site-packages\django\forms\forms.py" in _get_errors 112. self.full_clean() File "C:\wamp\bin\Python26\lib\site-packages\django\forms\forms.py" in full_clean 269. self._post_clean() File "C:\wamp\bin\Python26\lib\site-packages\django\forms\models.py" in _post_clean 345. self.validate_unique() File "C:\wamp\bin\Python26\lib\site-packages\django\forms\models.py" in validate_unique 354. self.instance.validate_unique(exclude=exclude) File "C:\wamp\bin\Python26\lib\site-packages\django\db\models\base.py" in validate_unique 695. date_errors = self._perform_date_checks(date_checks) File "C:\wamp\bin\Python26\lib\site-packages\django\db\models\base.py" in _perform_date_checks 802. lookup_kwargs['%s__day' % unique_for] = date.day Exception Type: AttributeError at /admin/editoriales/editorial/add/ Exception Value: 'NoneType' object has no attribute 'day' thanks guys sorry with my English

    Read the article

  • So now that Django 1.2 is officially out...

    - by Fedor
    Since I have Django 1.1x on my Debian setup - how can I use virtualenv or similar and not have it mess up my system's default django version which in turn would break all my sites? Detailed instructions or a great tutorial link would very much be appreciated - please don't offer vague advice since I'm still a noob. Currently I store all my django projects in ~/django-sites and I am using Apache2 + mod_wsgi to deploy.

    Read the article

  • Django-Registration & Django-Profile, using your own custom form

    - by Issy
    Hey All, I am making use of django-registration and django-profile to handle registration and profiles. I would like to create a profile for the user at the time of registration. I have created a custom registration form, and added that to the urls.py using the tutorial on: http://dewful.com/?p=70 The basic idea in the tutorial is to override the default registration form to create the profile at the same time. forms.py - In my profiles app from django import forms from registration.forms import RegistrationForm from django.utils.translation import ugettext_lazy as _ from profiles.models import UserProfile from registration.models import RegistrationProfile attrs_dict = { 'class': 'required' } class UserRegistrationForm(RegistrationForm): city = forms.CharField(widget=forms.TextInput(attrs=attrs_dict)) def save(self, profile_callback=None): new_user = RegistrationProfile.objects.create_inactive_user(username=self.cleaned_data['username'], password=self.cleaned_data['password1'], email=self.cleaned_data['email']) new_profile = UserProfile(user=new_user, city=self.cleaned_data['city']) new_profile.save() return new_user In urls.py from profiles.forms import UserRegistrationForm and url(r'^register/$', register, {'backend': 'registration.backends.default.DefaultBackend', 'form_class' : UserRegistrationForm}, name='registration_register'), The form is displayed, and i can enter in City, however it does not save or create the entry in the DB.

    Read the article

  • django error ,about django-sphinx

    - by zjm1126
    from django.db import models from djangosphinx.models import SphinxSearch class MyModel(models.Model): search = SphinxSearch() # optional: defaults to db_table # If your index name does not match MyModel._meta.db_table # Note: You can only generate automatic configurations from the ./manage.py script # if your index name matches. search = SphinxSearch('index_name') # Or maybe we want to be more.. specific searchdelta = SphinxSearch( index='index_name delta_name', weights={ 'name': 100, 'description': 10, 'tags': 80, }, mode='SPH_MATCH_ALL', rankmode='SPH_RANK_NONE', ) queryset = MyModel.search.query('query') results1 = queryset.order_by('@weight', '@id', 'my_attribute') results2 = queryset.filter(my_attribute=5) results3 = queryset.filter(my_other_attribute=[5, 3,4]) results4 = queryset.exclude(my_attribute=5)[0:10] results5 = queryset.count() # as of 2.0 you can now access an attribute to get the weight and similar arguments for result in results1: print result, result._sphinx # you can also access a similar set of meta data on the queryset itself (once it's been sliced or executed in any way) print results1._sphinx and Traceback (most recent call last): File "D:\zjm_code\sphinx_test\models.py", line 1, in <module> from django.db import models File "D:\Python25\Lib\site-packages\django\db\__init__.py", line 10, in <module> if not settings.DATABASE_ENGINE: File "D:\Python25\Lib\site-packages\django\utils\functional.py", line 269, in __getattr__ self._setup() File "D:\Python25\Lib\site-packages\django\conf\__init__.py", line 38, in _setup raise ImportError("Settings cannot be imported, because environment variable %s is undefined." % ENVIRONMENT_VARIABLE) ImportError: Settings cannot be imported, because environment variable DJANGO_SETTINGS_MODULE is undefined.

    Read the article

  • Django TemplateSyntaxError only on live server (templates exist)

    - by Tom
    I'm getting a strange error that only occurs on the live server. My Django templates directory is set up like so base.html two-column-base.html portfolio index.html extranet base.html index.html The portfolio pages work correctly locally on multiple machines. They inherit from either the root base.html or two-column-base.html. However, now that I've posted them to the live box (local machines are Windows, live is Linux), I get a TemplateSyntaxError: "Caught TemplateDoesNotExist while rendering: base.html" when I try to load any portfolio pages. It seems to be a case where the extends tag won't work in that root directory (???). Even if I do a direct_to_template on two-column-base.html (which extends base.html), I get that error. The extranet pages all work perfectly, but those templates all live inside the /extranet folder and inherit from /extranet/base.html. Possible issues I've checked: file permissions on the server are fine the template directory is correct on the live box (I'm using os.path.dirname(os.path.realpath(__file__)) to make things work across machines) files exist and the /templates directories exactly match my local copy removing the {% extends %} block from the top of any broken template causes the templates to render without a problem manually starting a shell session and calling get_template on any of the files works, but trying to render it blows up with the same exception on any of the extended templates. Doing the same with base.html, it renders perfectly (base.html also renders via direct_to_template) Django 1.2, Python 2.6 on Webfaction. Apologies in advance because this is my 3rd or 4th "I'm doing something stupid" question in a row. The only x-factor I can think of is this is my first time using Mercurial instead ofsvn. Not sure how I could have messed things up via that. EDIT: One possible source of problems: local machine is Python 2.5, live is 2.6. Here's a traceback of me trying to render 'two-column-base.html', which extends 'base.html'. Both files are in the same directory, so if it can find the first, it can find the second. c is just an empty Context object. >>> render_to_string('two-column-base.html', c) Traceback (most recent call last): File "<console>", line 1, in <module> File "/home/lightfin/webapps/django/lib/python2.6/django/template/loader.py", line 186, in render_to_string return t.render(context_instance) File "/home/lightfin/webapps/django/lib/python2.6/django/template/__init__.py", line 173, in render return self._render(context) File "/home/lightfin/webapps/django/lib/python2.6/django/template/__init__.py", line 167, in _render return self.nodelist.render(context) File "/home/lightfin/webapps/django/lib/python2.6/django/template/__init__.py", line 796, in render bits.append(self.render_node(node, context)) File "/home/lightfin/webapps/django/lib/python2.6/django/template/debug.py", line 72, in render_node result = node.render(context) File "/home/lightfin/webapps/django/lib/python2.6/django/template/loader_tags.py", line 103, in render compiled_parent = self.get_parent(context) File "/home/lightfin/webapps/django/lib/python2.6/django/template/loader_tags.py", line 100, in get_parent return get_template(parent) File "/home/lightfin/webapps/django/lib/python2.6/django/template/loader.py", line 157, in get_template template, origin = find_template(template_name) File "/home/lightfin/webapps/django/lib/python2.6/django/template/loader.py", line 138, in find_template raise TemplateDoesNotExist(name) TemplateSyntaxError: Caught TemplateDoesNotExist while rendering: base.html I'm wondering if this is somehow related to the template caching that was just added to Django. EDIT 2 (per lazerscience): template-related settings: import os PROJECT_ROOT = os.path.dirname(os.path.realpath(__file__)) TEMPLATE_DIRS = ( os.path.join(PROJECT_ROOT, 'templates'), ) sample view: def project_list(request, jobs, extra_context={}): context = { 'jobs': jobs, } print context context.update(extra_context) return render_to_response('portfolio/index.html', context, context_instance=RequestContext(request)) The templates in reverse-order are: http://thosecleverkids.com/junk/index.html http://thosecleverkids.com/junk/portfolio-base.html http://thosecleverkids.com/junk/two-column-base.html http://thosecleverkids.com/junk/base.html though in the real project the first two live in a directory called "portfolio".

    Read the article

  • Odd behavior in Django Form (readonly field/widget)

    - by jamida
    I'm having a problem with a test app I'm writing to verify some Django functionality. The test app is a small "grade book" application that is currently using Alex Gaynor's readonly field functionality http://lazypython.blogspot.com/2008/12/building-read-only-field-in-django.html There are 2 problems which may be related. First, when I flop the comment on these 2 lines below: # myform = GradeForm(data=request.POST, instance=mygrade) myform = GradeROForm(data=request.POST, instance=mygrade) it works like I expect, except of course that the student field is changeable. When the comments are the shown way, the "studentId" field is displayed as a number (not the name, problem 1) and when I hit submit I get an error saying that studentId needs to be a Student instance. I'm at a loss as to how to fix this. I'm not wedded to Alex Gaynor's code. ANY code will work. I'm relatively new to both Python and Django, so the hints I've seen on websites that say "making a read-only field is easy" are still beyond me. // models.py class Student(models.Model): name = models.CharField(max_length=50) parent = models.CharField(max_length=50) def __unicode__(self): return self.name class Grade(models.Model): studentId = models.ForeignKey(Student) finalGrade = models.CharField(max_length=3) # testbed.grades.readonly is alex gaynor's code from testbed.grades.readonly import ReadOnlyField class GradeROForm(ModelForm): studentId = ReadOnlyField() class Meta: model=Grade class GradeForm(ModelForm): class Meta: model=Grade // views.py def modifyGrade(request,student): student = Student.objects.get(name=student) mygrade = Grade.objects.get(studentId=student) if request.method == "POST": # myform = GradeForm(data=request.POST, instance=mygrade) myform = GradeROForm(data=request.POST, instance=mygrade) if myform.is_valid(): grade = myform.save() info = "successfully updated %s" % grade.studentId else: # myform=GradeForm(instance=mygrade) myform=GradeROForm(instance=mygrade) return render_to_response('grades/modifyGrade.html',locals()) // template <p>{{ info }}</p> <form method="POST" action=""> <table> {{ myform.as_table }} </table> <input type="submit" value="Submit"> </form> // Alex Gaynor's code from django import forms from django.utils.html import escape from django.utils.safestring import mark_safe from django.forms.util import flatatt class ReadOnlyWidget(forms.Widget): def render(self, name, value, attrs): final_attrs = self.build_attrs(attrs, name=name) if hasattr(self, 'initial'): value = self.initial return mark_safe("<span %s>%s</span>" % (flatatt(final_attrs), escape(value) or '')) def _has_changed(self, initial, data): return False class ReadOnlyField(forms.FileField): widget = ReadOnlyWidget def __init__(self, widget=None, label=None, initial=None, help_text=None): forms.Field.__init__(self, label=label, initial=initial, help_text=help_text, widget=widget) def clean(self, value, initial): self.widget.initial = initial return initial

    Read the article

  • Simple Observation in Django: How Can I Correctly Modify The `attrs` sent to __new__ of a Django Mod

    - by DGGenuine
    Hello, I'm a strong proponent of the observer pattern, and this is what I'd like to be able to do in my Django models.py: class AModel(Model): __metaclass__ = SomethingMagical @post_save(AnotherModel) @classmethod def observe_another_model_saved(klass, sender, instance, created, **kwargs): pass @pre_init('YetAnotherModel') @classmethod def observe_yet_another_model_initializing(klass, sender, *args, **kwargs): pass @post_delete('DifferentApp.SomeModel') @classmethod def observe_some_model_deleted(klass, sender, **kwargs): pass This would connect a signal with sender = the decorator's argument and receiver = the decorated method. Right now my signal connection code all exists in __init__.py which is okay, but a little unmaintainable. I want this code all in one place, the models.py file. Thanks to helpful feedback from the community I'm very close (I think.) (I'm using a metaclass solution instead of the class decorator solution in the previous question/answer because you can't set attributes on classmethods, which I need.) I am having a strange error I don't understand. At the end of my post are the contents of a models.py that you can pop into a fresh project/application to see the error. Set your database to sqlite and add the application to installed apps. This is the error: Validating models... Unhandled exception in thread started by Traceback (most recent call last): File "/Library/Python/2.6/site-packages//lib/python2.6/site-packages/django/core/management/commands/runserver.py", line 48, in inner_run File "/Library/Python/2.6/site-packages/django/core/management/base.py", line 253, in validate raise CommandError("One or more models did not validate:\n%s" % error_text) django.core.management.base.CommandError: One or more models did not validate: local.myothermodel: 'my_model' has a relation with model MyModel, which has either not been installed or is abstract. I've indicated a few different things you can comment in/out to fix the error. First, if you don't modify the attrs sent to the metaclass's __new__, then the error does not arise. (Note even if you copy the dictionary element by element into a new dictionary, it still fails; only using the exact attrs dictionary works.) Second, if you reference the first model by class rather than by string, the error also doesn't arise regardless of what you do in __new__. I appreciate your help. I'll be githubbing the solution if and when it works. Maybe other people would enjoy a simplified way to use Django signals to observe application happenings. #models.py from django.db import models from django.db.models.base import ModelBase from django.db.models import signals import pdb class UnconnectedMethodWrapper(object): sender = None method = None signal = None def __init__(self, signal, sender, method): self.signal = signal self.sender = sender self.method = method def post_save(sender): return _make_decorator(signals.post_save, sender) def _make_decorator(signal, sender): def decorator(view): return UnconnectedMethodWrapper(signal, sender, view) return decorator class ConnectableModel(ModelBase): """ A meta class for any class that will have static or class methods that need to be connected to signals. """ def __new__(cls, name, bases, attrs): unconnecteds = {} ## NO WORK newattrs = {} for name, attr in attrs.iteritems(): if isinstance(attr, UnconnectedMethodWrapper): unconnecteds[name] = attr newattrs[name] = attr.method #replace the UnconnectedMethodWrapper with the method it wrapped. else: newattrs[name] = attr ## NO WORK # newattrs = {} # for name, attr in attrs.iteritems(): # newattrs[name] = attr ## WORKS # newattrs = attrs new = super(ConnectableModel, cls).__new__(cls, name, bases, newattrs) for name, unconnected in unconnecteds.iteritems(): _connect_signal(unconnected.signal, unconnected.sender, getattr(new, name), new._meta.app_label) return new def _connect_signal(signal, sender, receiver, default_app_label): # full implementation also accepts basestring as sender and will look up model accordingly signal.connect(sender=sender, receiver=receiver) class MyModel(models.Model): __metaclass__ = ConnectableModel @post_save('In my application this string matters') @classmethod def observe_it(klass, sender, instance, created, **kwargs): pass @classmethod def normal_class_method(klass): pass class MyOtherModel(models.Model): ## WORKS # my_model = models.ForeignKey(MyModel) ## NO WORK my_model = models.ForeignKey('MyModel')

    Read the article

  • CPU fan kicks in to full gear when i try to install ubuntu 12.10 or LTS

    - by Remi cook
    Whenever I try to install (DUAL BOOT WITH WINDOWS 7) both versions of Ubuntu desktop on my PC the CPU fan starts spinning so fast that I couldn't even go through the installation for fear of my CPU exploding. In windows 7, the temp reaches 25-30 idle and 30-45 under full load. I tried installing through Wubi and by burning it to USB drive. Both wield the same results. I would appreciate any help. I'm a complete noob so take it easy one me. Intel Core i5 2500 @ 3.30GHz 4.00 GB Dual-Channel DDR3 @ 668MHz (9-9-9-24) Motherboard ASUSTeK Computer INC. P8Z68-V LX (LGA1155) Graphics AMD Radeon HD 6850 (Sapphire/PCPartner)

    Read the article

  • Uncontrolled Fan and Crash

    - by RobotbeatsHuman
    I don't have sensors to properly run lm-sensors. The computer will turn on but shortly there after all the fans in it will speed way up. It stays like this for a few minutes and then the computer shuts off. Tried resetting the BIO. Went to try installing a BIOs update but it wont stay on long enough for me to try that or to do a clean install. Could this be the motherboard dying? It's mainly the CPU fan that ends up going max. after a few minutes. I checked the PSU and It's a Dell Inspiron 580. If you need more system specs just le me know.

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >