Search Results

Search found 111890 results on 4476 pages for 'git update server info'.

Page 4/4476 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Windows Server 2003 Terminal Server does not give out all available licenses

    - by Erwin Blonk
    I installed the Terminal Server role in Windows Server 2003 Standard 64-bits. Still, only 2 connections are allowed. The License Manager says that there are 10 Device CALs available, which is correct, and that none are given out. For good measure I let the server reboot, to no effect. Before this, there was another server (same Windows, except that it is 32 bits) active as a licensing server. I removed the role first and then then added it to the new server. I then removed the Terminal Server Licensing Server component off the old one and added it to the new one. After that, I added to licenses. When that didn't give the required result, I rebooted to new server. Still, the new server, with licenses and all, acts as if it has the 2 license RDP. The server are all stand-alone, there is no active directory been set up. Both servers are in different workgroups. Update (4/12/10): The server has changed the entries in the Terminal Server Licensing a few times. After installing the licenses it added an entry of which the exact phrasing I forgot but it was about temporary Windows 2003 device licenses. Later it added Windows Server 2003 - TS Per Device CAL. The temporary held 2 licenses (standard RDP licenses, I think) and the other 10. At some point, seemingly unrelated from the testing we did, it used a licenses from the new pool. This morning, 2 licenses were used from the pool of 10 and only 1 from the temporary/RDP pool (I wish I had screenshots to show, it changed every few hours oir so it seems). Although I had already activated the server over the internet, and re-activated it, I decided to go through the whole procedure by phone. Long story short, here is what it says now: Existing Windows 2000 Server, type:built-in [no licenses used, I add for for sake of being complete] Windows Server 2003 - Terminal Server Per Device CAL Token, type:open [none of 10 used] Windows Server 2003 - TS Per Device CAL, type:open [3 of 10 used] As I tried to explain, this is the end result after a few changes, most of which I can't directly connect to any action from my part. Only going to the activation procedure by phone seemed to directly effect the TS, resulting in the above configuration. Still, it is impossible to connect with more than 3 people, which is 1 up from the 2 that could connect yesterday. TS does say 7 licenses are avaible. Yet it won't give them out.

    Read the article

  • Slow git clone and fetch

    - by EtienneT
    I setuped gitosis on a linux server following this tutorial: http://scie.nti.st/2007/11/14/hosting-git-repositories-the-easy-and-secure-way We are using git on our windows machines with TortoiseGit and msysgit. Pushing changes to the server is pretty fast, but when we want to clone or fetch changes from the remote server, it begins really fast (800k/s) and then drop pretty fast to around 3 to 30k/s and it can take forever to update. git-pull for small update is fast, but as soon as we have to download something of more than a few MB, it is slow. We are switching from SVN to git and this is holding us back from using git full time. Thanks!

    Read the article

  • Slow git clone and fetch

    - by EtienneT
    I setuped gitosis on a linux server following this tutorial: http://scie.nti.st/2007/11/14/hosting-git-repositories-the-easy-and-secure-way We are using git on our windows machines with TortoiseGit and msysgit. Pushing changes to the server is pretty fast, but when we want to clone or fetch changes from the remote server, it begins really fast (800k/s) and then drop pretty fast to around 3 to 30k/s and it can take forever to update. git-pull for small update is fast, but as soon as we have to download something of more than a few MB, it is slow. We are switching from SVN to git and this is holding us back from using git full time. Thanks!

    Read the article

  • Trying to create a git repo that does an automatic checkout everytime someone updates origin

    - by Dane Larsen
    Basically, I have a server with a git repo 'origin'. I'm trying to have another repo auto-pull from origin every time someone pushes code to it. I've been using the hooks in origin, specifically post-receive. So far, my post receive looks something like this: #!/bin/sh GIT_DIR=/home/<user>/<test_repo> git pull origin master But when I push to origin from another computer, I get the error: remote: fatal: Not a git repository: '/home/<user>/<test_repo>' However, test_repo most definitely is a git repo. I can cd into it and run 'git pull origin master' and it works fine. Is there an easier way to do what I'm trying to do? If not, what am I doing wrong with this approach? Thanks in advance. Edit, to clarify: The repo is a website in progress, and I'd like to have a version of it available at all times that is fully up to date.

    Read the article

  • Git Clone from SSH Repository

    - by Mike Silvis
    I used to be able to clone from my personal git repository but now i seem to be running into an error. user:dev.site.com mikesilvis$ git clone { my ssh directory } server@ipaddress's password: remote: Counting objects: 3622, done. remote: Compressing objects: 100% (2718/2718), done. error: git upload-pack: git-pack-objects died with error. fatal: git upload-pack: aborting due to possible repository corruption on the remote side. remote: aborting due to possible repository corruption on the remote side. fatal: early EOF fatal: index-pack failed It seems to be working however while I push files to the repository.

    Read the article

  • 'Important security update' for Firefox and flash plugin, but the update cannot be selected

    - by geoffrey
    [This question has been updated as I now have the same problem with Firefox in addition to flash plugin] The update manager (on Ubuntu 12.04, 64bit) shows an 'important security update' for flashplugin-installer:i386, firefox, and firefox-globalmenu. The update is unticked, and cannot be selected, and therefore cannot be updated (I can update other packages without problems). Actually the flashplugin-installer package does not appear to be installed on my computer (judging from the Software Centre). I can't remember how I installed flash, probably directly from the Adobe website. The updater asks me if I want to do a partial upgrade. When running sudo apt-get update && sudo apt-get upgrade from terminal, I get the following: The following packages have been kept back: firefox firefox-globalmenu flashplugin-installer:i386

    Read the article

  • Git tutorial: Understanding git pull and branches (using a specific example repo)

    - by dreftymac
    Backround: Suppose I have the following Git URLs (hosted on github) http://github.com/mikl/drupal.git git://github.com/mikl/drupal.git (Git read-only) I am interested in having a local copy of this repository so I can pratice working with branches in git and see how my local working tree can change depending on which branch I am working with. Questions: To get started, I set up a local directory and do git clone git://github.com/mikl/drupal.git ... Will this clone all of the branches? Or will it only clone master? The web front-end for github gives me a "drop down" menu that allows me to switch branches ... Does changing this drop-down actually change which branch I will be grabbing when I run git clone? If I want a new copy of this repository on my local machine, but I am interested in only two branches of this repository and I want to ignore all the rest, what command do I use to ensure I clone only those two branches and nothing else (assume one of the branches is master)?

    Read the article

  • How do I install git/git-svn on RHEL5 with a custom perl install?

    - by kbosak
    I've had nothing but trouble trying to install Git on RHEL5. First I tried from source, but ran into several issues with installing the docs. There appeared to be missing libs and such for parsing xml that I couldn't figure out how to get installed and recognized. Then I tried using the EPEL yum repository and was able to install git and its docs but now git-svn is not working. It complains about not finding the perl modules Git.pm and SVN/Core.pm. When I set the GITPERLLIB environment variable to the location of those libs it seg faults. Some background: RHEL5 came with perl 5.8.8, but we wanted to use 5.10 so I installed that from source (to a custom location). Someone then symlinked the system perl binary to this newer version of Perl to make sure nobody uses the wrong version. Each developer also has their own build of Perl. So I'm wondering what's the best way to install Git on this system and have both the docs and git-svn working correctly for each user. Unfortunately I'm a developer and not as good with system administration so take it easy on me.

    Read the article

  • Solaris 10 opencsw git package issue with bitbucket git hosting

    - by zephyrus00jp
    Has anyone tried using `git' from opencsw package in order to work with bitbucket source hosting service (under solaris10)? I tried to use git as the bitbucket documentation explains, and - under Debian GNU/Linux, it worked flawlessly as described, but - under Solaris 10, I got Authentication Failed message. I even tried to run truss to see anything is suspicious but could not find any smoking gun under solaris why it failed. ldd git-binary didnd't show anything suspicious either (except for the libcrypt library which could be a suspicious to think about export restrictions. Have they shipped incompatible version? BUT since the password is typed into https: connection, I suspect it is only a matter of web-level cryptography and should be universal these days.) I am now tempted to compile git suite under solaris 10, but I did find people who seem to be using git with bitbucket under solaris 10 and am wondering what could be wrong.

    Read the article

  • Best way to fork SVN project with Git

    - by Jeremy Thomerson
    I have forked an SVN project using Git because I needed to add features that they didn't want. But at the same time, I wanted to be able to continue pulling in features or fixes that they added to the upstream version down into my fork (where they don't conflict). So, I have my Git project with the following branches: master - the branch I actually build and deploy from feature_* - feature branches where I work or have worked on new things, which I then merge to master when complete vendor-svn - my local-only git-svn branch that allows me to "git svn rebase" from their svn repo vendor - my local branch that i merge vendor-svn into. then i push this (vendor) branch to the public git repo (github) So, my flow is something like this: git checkout vendor-svn git svn rebase git checkout vendor git merge vendor-svn git push origin vendor Now, the question comes here: I need to review each commit that they made (preferably individually since at this point I'm about twenty commits behind them) before merging them into master. I know that I could run git checkout master; git merge vendor, but this would pull in all changes and commit them, without me being able to see if they conflict with what I need. So, what's the best way to do this? Git seems like a great tool for handling forks of projects since you can pull and push from multiple repos - I'm just not experienced with it enough to know the best way of doing this. Here's the original SVN project I'm talking about: https://appkonference.svn.sourceforge.net/svnroot/appkonference My fork is at github.com/jthomerson/AsteriskAudioKonf (sorry - I couldn't make it a link since I'm a new user here)

    Read the article

  • git-svn guestion about creating local branches

    - by leeed25d
    Is there a way to create a local branch, or modify an existing local branch, in such a way that it cannot be dcommit'ed to the svn repo? Here's a description of the scenario. git checkout -b local.farBranch remotes/farBranch git checkout -b patched.local.farBranch git merge local.patches <work on patched branch && test> <do not commit onto patched.local.farBranch> git checkout local.farBranch git commit -am "some changes" git rebase local.farBranch patched.local.farBranch <another work test cycle> git checkout local.farBranch git commit -am "last changes" git svn dcommit Now, I never want to dcommit patched.local.farBranch (which is tracking remotes/farBranch) because that would put my local patches into the SVN repository. This is not a fatal problem but it is a pain in the keester because the patch has to be removed when the SVN farBranch is eventally (SVN) merged onto the trunk. So what I am looking for is a way to prevent this git checkout patched.local.farBranch git svn dcommit <<== ERROR git checkout local.farBranch git svn dcommit <<== OK

    Read the article

  • Git - switching between branches in the middle of work

    - by Art
    For various reasons (code review mostly) I need to switch from current development branch to other branches quite often. Currently, I use either 'git stash' to shelve the uncommitted changes, checkout other branch, then switch back and do 'git stash apply' However, sometimes I'd have some newly added files there, which are not tracked. Unfortunately, stashing does not affect them. In this case I'd have to add them to the index and stash. What I am looking here for is a workflow where I'd have to perform a minimal set of actions to switch the branches, preferably avoiding adding of files into the index.

    Read the article

  • Perforce Git Fusion apporte de nouvelles capacités flexibles pour Git, l'outil téléchargeable gratuitement

    Perforce Git Fusion apporte de nouvelles capacités flexibles pour Git l'outil téléchargeable gratuitement Résoudre les difficultés inhérentes à l'utilisation de Git si le projet ne peut pas proprement s'inviter dans un unique dépôt Git : c'est le but essentiel de Perforce Git Fusion. L'outil met fin à ces difficultés, tout en offrant aux utilisateurs la possibilité de travailler de la façon qu'ils préfèrent. Les développeurs peuvent ainsi continuer d'utiliser Git sans modifications, tandis que les responsables de la distribution et les administrateurs ont la flexibilité, s'ils le souhaitent, de préserver leurs outils et processus favoris. Pour rappel, Git est un logiciel de gestio...

    Read the article

  • Why is Git telling me "Your branch is ahead of 'origin/master' by 11 commits." and how do I get it t

    - by spilth
    I'm a Git newbie. I recently moved a Rails project from Subversion to Git. I followed the tutorial here: http://www.simplisticcomplexity.com/2008/03/05/cleanly-migrate-your-subversion-repository-to-a-git-repository/ I am also using unfuddle.com to store my code. I make changes on my Mac laptop on the train to/from work and then push them to unfuddle when I have a network connection using the following command: git push unfuddle master I use Capistrano for deployments and pull code from the unfuddle repository using the master branch. Lately I've noticed the following message when I run "git status" on my laptop: # On branch master # Your branch is ahead of 'origin/master' by 11 commits. # nothing to commit (working directory clean) And I'm confused as to why. I thought my laptop was the origin... but don't know if either the fact that I originally pulled from Subversion or push to Unfuddle is what's causing the message to show up. How can I: Find out where Git thinks 'origin/master' is? If it's somewhere else, how do I turn my laptop into the 'origin/master'? Get this message to go away. It makes me think Git is unhappy about something. My mac is running Git version 1.6.0.1. When I run git remote show origin as suggested by dbr, I get the following: ~/Projects/GeekFor/geekfor 10:47 AM $ git remote show origin fatal: '/Users/brian/Projects/GeekFor/gf/.git': unable to chdir or not a git archive fatal: The remote end hung up unexpectedly When I run git remote -v as suggested by Aristotle Pagaltzis, I get the following: ~/Projects/GeekFor/geekfor 10:33 AM $ git remote -v origin /Users/brian/Projects/GeekFor/gf/.git unfuddle [email protected]:spilth/geekfor.git Now, interestingly, I'm working on my project in the geekfor directory but it says my origin is my local machine in the gf directory. I believe gf was the temporary directory I used when converting my project from Subversion to Git and probably where I pushed to unfuddle from. Then I believe I checked out a fresh copy from unfuddle to the geekfor directory. So it looks like I should follow dbr's advice and do: git remote rm origin git remote add origin [email protected]:spilth/geekfor.git

    Read the article

  • git private server error: "Permission denied (publickey)."

    - by goddfree
    I followed the instructions here in order to set up a private git server on my Amazon EC2 instance. However, I am having problems when trying to SSH into the git account. Specifically, I get the error "Permission denied (publickey)." Here are the permissions of my files/folders on the EC2 server: drwx------ 4 git git 4096 Aug 13 19:52 /home/git/ drwx------ 2 git git 4096 Aug 13 19:52 /home/git/.ssh -rw------- 1 git git 400 Aug 13 19:51 /home/git/.ssh/authorized_keys Here are the permissions of my files/folders on my own computer: drwx------ 5 CYT staff 170 Aug 13 14:51 .ssh -rw------- 1 CYT staff 1679 Aug 13 13:53 .ssh/id_rsa -rw-r--r-- 1 CYT staff 400 Aug 13 13:53 .ssh/id_rsa.pub -rw-r--r-- 1 CYT staff 1585 Aug 13 13:53 .ssh/known_hosts When checking my logs in /var/log/secure, I used to get the following error message every time I tried to SSH: Authentication refused: bad ownership or modes for file /home/git/.ssh/authorized_keys However, after making a few permission changes, I no longer get this error message. Despite this, I am still getting the "Permission denied (publickey)." message every time I try to SSH. The command I am using to SSH is ssh -T git@my-ip. Here is the full log I get when I run ssh -vT [email protected]: OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to my-ip [my-ip] port 22. debug1: Connection established. debug1: identity file /Users/CYT/.ssh/id_rsa type -1 debug1: identity file /Users/CYT/.ssh/id_rsa-cert type -1 debug1: identity file /Users/CYT/.ssh/id_dsa type -1 debug1: identity file /Users/CYT/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.2 debug1: match: OpenSSH_6.2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 08:ad:8a:bc:ab:4d:5f:73:24:b2:78:69:46:1a:a5:5a debug1: Host 'my-ip' is known and matches the RSA host key. debug1: Found key in /Users/CYT/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /Users/CYT/.ssh/id_rsa debug1: Trying private key: /Users/CYT/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). I have spent a few hours going through threads on various sites, including SO and SF, looking for a solution. It seems that the permissions for my files are all okay, but I just can't figure out the problem. Any help would be greatly appreciated. Edit: EEAA: Here are the outputs you requested: $ getent passwd git git:x:503:504::/home/git:/bin/bash $ grep ssh ~git/.ssh/authorized_keys | wc -l grep: /home/git/.ssh/authorized_keys: Permission denied 0

    Read the article

  • Windows Server 2003 Terminal Server with installed licenses will not go beyond 2 connections

    - by Erwin Blonk
    I installed the Terminal Server role in Windows Server 2003 Standard 64-bits. Still, only 2 connections are allowed. The License Manager says that there are 10 Device CALs available, which is correct, and that none are given out. For good measure I let the server reboot, to no effect. Before this, there was another server (same Windows, except that it is 32 bits) active as a licensing server. I removed the role first and then then added it to the new server. I then removed the Terminal Server Licensing Server component off the old one and added it to the new one. After that, I added to licenses. When that didn't give the required result, I rebooted to new server. Still, the new server, with licenses and all, acts as if it has the 2 license RDP. The server are all stand-alone, there is no active directory been set up. Both servers are in different workgroups.

    Read the article

  • Git init - .git: Permission Denied

    - by Gcoop
    Hi All, I am trying to initiate git on my remote server using ssh. When I run git init On the server in a folder I have write permissions to I get the following error. .git: Permission denied Do I need to assign any other permissions on that folder to be able to create the repository? Thanks

    Read the article

  • How to do 'git status' on untracked directory?

    - by meowsqueak
    I have 6,000 untracked files in one subdirectory and I'm constructing .gitignore files to filter out the unwanted ones. I'm testing my gitignore filters as I go by running 'git status'. However, I have a larger number of untracked other files in a different subdirectory, so 'git status' shows all of those too, which makes it very hard to see what the .gitignore rules are doing. If the files were tracked, then I could just do 'git status .' and it would restrict the git-status output to only those files in the current directory, but because the current directory and all its contents are untracked, 'git status .' returns "error: pathspec . did not match any file(s) known to git." I'm using git-1.6.6.1 for this, although interestingly my testing shows that git-1.7.1 (on a different system) does actually let you do git-status on an untracked directory. Unfortunately I can't upgrade git on this system. Is there a known workaround for -1.6.6.1?

    Read the article

  • Migrate database from SQL Server Standard to SQL Server Express for DotNetNuke

    - by Bjørn
    Hello, we have an old server that we want to dedicate fully as a public webserver (hosting a few DotNetNuke sites), and for this purpose we would like to install SQL Server Express (probably 2008) on the server and thus have both the Database server and the Web Server on the machine. But: The databases for the webserver are hosted on a SQL Server 2005 Standard today. So the question is: Is it possible to move a database from a Standard Server to an Express Server?

    Read the article

  • Windows Server 2003 Terminal Server does not give out all available licenses (solved)

    - by Erwin Blonk
    I installed the Terminal Server role in Windows Server 2003 Standard 64-bits. Still, only 2 connections are allowed. The License Manager says that there are 10 Device CALs available, which is correct, and that none are given out. For good measure I let the server reboot, to no effect. Before this, there was another server (same Windows, except that it is 32 bits) active as a licensing server. I removed the role first and then then added it to the new server. I then removed the Terminal Server Licensing Server component off the old one and added it to the new one. After that, I added to licenses. When that didn't give the required result, I rebooted to new server. Still, the new server, with licenses and all, acts as if it has the 2 license RDP. The server are all stand-alone, there is no active directory been set up. Both servers are in different workgroups. Update (4/12/10): The server has changed the entries in the Terminal Server Licensing a few times. After installing the licenses it added an entry of which the exact phrasing I forgot but it was about temporary Windows 2003 device licenses. Later it added Windows Server 2003 - TS Per Device CAL. The temporary held 2 licenses (standard RDP licenses, I think) and the other 10. At some point, seemingly unrelated from the testing we did, it used a licenses from the new pool. This morning, 2 licenses were used from the pool of 10 and only 1 from the temporary/RDP pool (I wish I had screenshots to show, it changed every few hours oir so it seems). Although I had already activated the server over the internet, and re-activated it, I decided to go through the whole procedure by phone. Update 2 (4/12/10) The problem has been solved. It seems the activation over the web, while it said to have succeeded, did not work correctly. After activating by phone, it did work. What was different from the old setup and what put me on the wrong foot from that moment, was that I now need to create seperate user account because a session with one user account will be taken over by someone else when that account is used by that person. On the previous server, it was possible to open several sesions with the same account. We now use Per Device licenses, I'm not sure what was used before. Thanks all for the replies.

    Read the article

  • WD MBWE II (White Strip Light) 2TB - unable to access data

    - by user210477
    I have a WD MBWE II (White Strip Light) 2TB - (WD20000H2NC-00) Was working fine until a few days ago. I guess there was a power failure and after that I am unable to access the 'Public' or the 'Download' folder anymore. I have been searching for answers everywhere but came up empty handed. Web GUI still works, SSH works. I hooked up both the drives on my PC and UFS Explorer sees the drive. But so far I am unable to retrieve any of my data. I do not remember what RAID setting I used when I first got the drive. I can see from GUI that it is set as "Stripe". The drive contains 10 years of family pictures which I really do not want to loose. Sadly and stupidly, I didn't even keep a backup of this drive. Can somebody please help or point me in the right direction. Thank you in advance for your help. Disk Utility on Ubuntu reports 1405 bad sectors on one drive. How can I retrieve my data? Please help. Logs below: ~ # mdadm --detail /dev/md[012345678] /dev/md0: Version : 0.90 Creation Time : Wed Jul 15 08:36:17 2009 Raid Level : raid1 Array Size : 1959872 (1914.26 MiB 2006.91 MB) Used Dev Size : 1959872 (1914.26 MiB 2006.91 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:53:29 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 04f7a661:98983b3b:26b29e4f:9b646adb Events : 0.266 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 /dev/md1: Version : 0.90 Creation Time : Wed Jul 15 08:36:18 2009 Raid Level : raid1 Array Size : 256896 (250.92 MiB 263.06 MB) Used Dev Size : 256896 (250.92 MiB 263.06 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Oct 30 22:08:21 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : aaa7b859:c475312d:efc5a766:6526b867 Events : 0.10 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 8 18 1 active sync /dev/sdb2 /dev/md2: Version : 0.90 Creation Time : Sat Sep 25 10:01:26 2010 Raid Level : raid0 Array Size : 1947045760 (1856.85 GiB 1993.77 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:30:53 2013 State : active Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K UUID : 01dae60a:6831077b:77f74530:8680c183 Events : 0.97 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 8 20 1 active sync /dev/sdb4 /dev/md3: Version : 0.90 Creation Time : Wed Jul 15 08:36:18 2009 Raid Level : raid1 Array Size : 987904 (964.91 MiB 1011.61 MB) Used Dev Size : 987904 (964.91 MiB 1011.61 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:26:33 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 3f4099f2:72e6171b:5ba962fd:48464a62 Events : 0.54 Number Major Minor RaidDevice State 0 8 3 0 active sync /dev/sda3 1 8 19 1 active sync /dev/sdb3 mdadm: md device /dev/md4 does not appear to be active. mdadm: md device /dev/md5 does not appear to be active. mdadm: md device /dev/md6 does not appear to be active. mdadm: md device /dev/md7 does not appear to be active. mdadm: md device /dev/md8 does not appear to be active. ~ # cat /etc/mtab securityfs /sys/kernel/security securityfs rw 0 0 /dev/md2 /DataVolume xfs rw,usrquota 0 0 /dev/md4 /ExtendVolume xfs rw,usrquota 0 0 ~ # df -k Filesystem 1k-blocks Used Available Use% Mounted on /dev/md0 1929044 145092 1685960 8% / /dev/md3 972344 123452 799500 13% /var /dev/ram0 63412 20 63392 0% /mnt/ram ~ # mdadm -D /dev/md2 /dev/md2: Version : 0.90 Creation Time : Sat Sep 25 10:01:26 2010 Raid Level : raid0 Array Size : 1947045760 (1856.85 GiB 1993.77 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:30:53 2013 State : active Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K UUID : 01dae60a:6831077b:77f74530:8680c183 Events : 0.97 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 8 20 1 active sync /dev/sdb4 ~ # mdadm -D /dev/md4 mdadm: md device /dev/md4 does not appear to be active. ~ # mount /dev/root on / type ext3 (rw,noatime,data=ordered) proc on /proc type proc (rw) sys on /sys type sysfs (rw) /dev/pts on /dev/pts type devpts (rw) securityfs on /sys/kernel/security type securityfs (rw) /dev/md3 on /var type ext3 (rw,noatime,data=ordered) /dev/ram0 on /mnt/ram type tmpfs (rw) ~ # cat /var/log/messages Oct 29 18:04:50 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 29 18:04:59 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 29 18:04:59 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 29 18:17:45 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 29 18:17:53 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 29 18:17:53 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 00:50:11 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 00:50:19 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 00:50:19 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 16:29:47 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 16:30:00 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 16:30:00 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 18:27:22 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 18:27:30 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 18:27:30 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 19:06:03 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 19:06:10 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 19:06:10 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 19:14:58 shmotashNAS daemon.warn wixEvent[3462]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 30 19:20:05 shmotashNAS daemon.alert wixEvent[3462]: Thermal Alarm - System temperature exceeded threshold.(66 degrees) Oct 30 19:58:29 shmotashNAS daemon.alert wixEvent[3462]: HDD SMART - HDD 1 SMART Health Status: Failed. Oct 30 22:05:39 shmotashNAS daemon.info init: Starting pid 13043, console /dev/null: '/usr/bin/killall' Oct 30 22:05:39 shmotashNAS syslog.info System log daemon exiting. Oct 30 22:08:09 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 30 22:08:09 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:08:19 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:08:25 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:08:37 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:08:44 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:08:46 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:30 - 22:08:46 [Version 01.09.00.96] ++++++++++++++ Oct 30 22:08:46 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 30 22:08:46 shmotashNAS syslog.info miocrawler: ****** database does not exist. ret = -1, creating path Oct 30 22:08:49 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 30 22:08:50 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 30 22:08:51 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 30 22:08:51 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 30 22:08:51 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 30 22:08:52 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 30 22:08:52 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:09:10 shmotashNAS daemon.info init: Starting pid 4605, console /dev/null: '/bin/touch' Oct 30 22:09:10 shmotashNAS daemon.info init: Starting pid 4607, console /dev/ttyS0: '/sbin/getty' Oct 30 22:09:10 shmotashNAS daemon.info wixEvent[3557]: System Startup - System startup. Oct 30 22:09:16 shmotashNAS daemon.warn wixEvent[3557]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 30 22:14:14 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:14:21 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:14:21 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:29:36 shmotashNAS daemon.warn wixEvent[3557]: System Reboot - System will reboot. Oct 30 22:29:40 shmotashNAS daemon.info init: Starting pid 5974, console /dev/null: '/usr/bin/killall' Oct 30 22:29:40 shmotashNAS syslog.info System log daemon exiting. Oct 30 22:47:56 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 30 22:47:56 shmotashNAS daemon.warn wixEvent[3461]: Network Link - NIC 1 link is down. Oct 30 22:48:02 shmotashNAS daemon.info wixEvent[3461]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:48:02 shmotashNAS daemon.info wixEvent[3461]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:48:09 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:30 - 22:48:09 [Version 01.09.00.96] ++++++++++++++ Oct 30 22:48:09 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 30 22:48:09 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Oct 30 22:48:10 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 30 22:48:10 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 30 22:48:27 shmotashNAS daemon.info init: Starting pid 4079, console /dev/null: '/bin/touch' Oct 30 22:48:27 shmotashNAS daemon.info init: Starting pid 4080, console /dev/ttyS0: '/sbin/getty' Oct 30 22:48:28 shmotashNAS daemon.info wixEvent[3461]: System Startup - System startup. Oct 30 22:49:01 shmotashNAS daemon.warn wixEvent[3461]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 30 23:51:11 shmotashNAS daemon.warn wixEvent[3461]: System Reboot - System will reboot. Oct 30 23:51:16 shmotashNAS daemon.info init: Starting pid 6498, console /dev/null: '/usr/bin/killall' Oct 30 23:51:16 shmotashNAS syslog.info System log daemon exiting. Oct 30 23:54:19 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 30 23:55:37 shmotashNAS daemon.info wixEvent[3476]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 23:55:37 shmotashNAS daemon.info wixEvent[3476]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 23:55:44 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:30 - 23:55:44 [Version 01.09.00.96] ++++++++++++++ Oct 30 23:55:44 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 30 23:55:44 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Oct 30 23:55:45 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 30 23:55:45 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 30 23:55:58 shmotashNAS daemon.info init: Starting pid 4115, console /dev/null: '/bin/touch' Oct 30 23:55:58 shmotashNAS daemon.info init: Starting pid 4116, console /dev/ttyS0: '/sbin/getty' Oct 30 23:55:58 shmotashNAS daemon.info wixEvent[3476]: System Startup - System startup. Oct 30 23:56:33 shmotashNAS daemon.warn wixEvent[3476]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 31 00:29:14 shmotashNAS auth.info sshd[5409]: Server listening on 0.0.0.0 port 22. Oct 31 00:31:25 shmotashNAS auth.info sshd[5486]: Accepted password for root from 192.168.1.100 port 50785 ssh2 Oct 31 00:33:44 shmotashNAS auth.info sshd[5565]: Accepted password for root from 192.168.1.100 port 50817 ssh2 Oct 31 00:36:39 shmotashNAS daemon.info init: Starting pid 5680, console /dev/null: '/usr/bin/killall' Oct 31 00:36:39 shmotashNAS syslog.info System log daemon exiting. Oct 31 00:40:44 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 31 00:40:51 shmotashNAS daemon.info wixEvent[3464]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 31 00:40:51 shmotashNAS daemon.info wixEvent[3464]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:31 - 00:41:00 [Version 01.09.00.96] ++++++++++++++ Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 31 00:41:01 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 31 00:41:14 shmotashNAS daemon.info init: Starting pid 4101, console /dev/null: '/bin/touch' Oct 31 00:41:14 shmotashNAS daemon.info init: Starting pid 4102, console /dev/ttyS0: '/sbin/getty' Oct 31 00:41:15 shmotashNAS daemon.info wixEvent[3464]: System Startup - System startup. Oct 31 00:41:47 shmotashNAS daemon.warn wixEvent[3464]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 31 01:13:19 shmotashNAS daemon.info init: Starting pid 5385, console /dev/null: '/usr/bin/killall' Oct 31 01:13:19 shmotashNAS syslog.info System log daemon exiting. Nov 1 13:26:25 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Nov 1 13:26:32 shmotashNAS daemon.info wixEvent[3471]: Network Link - NIC 1 link is up 100 Mbps full duplex. Nov 1 13:26:32 shmotashNAS daemon.info wixEvent[3471]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Nov 1 13:26:38 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:11:01 - 13:26:38 [Version 01.09.00.96] ++++++++++++++ Nov 1 13:26:38 shmotashNAS syslog.info miocrawler: mc_db_init ... Nov 1 13:26:38 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Nov 1 13:26:39 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Nov 1 13:26:39 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === inotify init done. Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === Walking directory done. Nov 1 13:26:52 shmotashNAS daemon.info init: Starting pid 4078, console /dev/null: '/bin/touch' Nov 1 13:26:52 shmotashNAS daemon.info init: Starting pid 4079, console /dev/ttyS0: '/sbin/getty' Nov 1 13:26:52 shmotashNAS daemon.info wixEvent[3471]: System Startup - System startup. Nov 1 13:27:28 shmotashNAS daemon.warn wixEvent[3471]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Nov 1 13:44:48 shmotashNAS auth.info sshd[5375]: Accepted password for root from 192.168.1.103 port 50217 ssh2 Nov 1 13:51:08 shmotashNAS auth.info sshd[5894]: Accepted password for root from 192.168.1.103 port 50380 ssh2

    Read the article

  • AD GIT SELinux RHEL 6 : Can not get SELinux to allow connetion to git

    - by Johan Sörell
    I have a problem with SELinux! I have installed git on Red Hat Enterprise 6 with AD group control and SSL Cert . Everything works fine if I do setenforce 0 ( set SELinux in detection only mode ) or if I do semanage permissive -a httpd_t (Set httpd_t in detection only mode) I do not want to use this on my git production server. Is there anyone out there who can help we with SELinux? Below is some info that you might need to be able to help me: All help I can get would be apriciated: This is the output of ls -lZa /preproduction/git/repositories/ ls -lZa /preproduction/git/repositories/ drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 . drwxr-xr-x. apache apache unconfined_u:object_r:file_t:s0 .. drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 playground drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 shamrock.git drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 test Here is the out put of getsebool -a |grep -i httpd getsebool -a |grep -i httpd allow_httpd_anon_write --> off allow_httpd_mod_auth_ntlm_winbind --> off allow_httpd_mod_auth_pam --> off allow_httpd_sys_script_anon_write --> off httpd_builtin_scripting --> on httpd_can_check_spam --> off httpd_can_network_connect --> off httpd_can_network_connect_cobbler --> off httpd_can_network_connect_db --> off httpd_can_network_memcache --> off httpd_can_network_relay --> off httpd_can_sendmail --> off httpd_dbus_avahi --> on httpd_enable_cgi --> on httpd_enable_ftp_server --> off httpd_enable_homedirs --> off httpd_execmem --> off httpd_read_user_content --> off httpd_setrlimit --> off httpd_ssi_exec --> off httpd_tmp_exec --> off httpd_tty_comm --> on httpd_unified --> on httpd_use_cifs --> off httpd_use_gpg --> off httpd_use_nfs --> off Tis is the status of : sestatus sestatus SELinux status: enabled SELinuxfs mount: /selinux Current mode: enforcing Mode from config file: enforcing Policy version: 24 Policy from config file: targeted

    Read the article

  • SQL Server Agent was not running on Server Dynamics CRM 2013

    - by No1_Melman
    I'm trying to install Dynamics CRM 2013 on a server. This server is on a VM. There are several other VMs, an ADDS & DNS, a MSSQL and a WebServer VM. Each server is a Windows Server 2012 R2. The SQL Server is 2012 Enterprise. Each VM is part of the main Domain, set by the ADDS & DNS. NSLookup confirms I can see the computer at the right IP address. Each separate VM has its own static IP, the DNS is set to the ADDS & DNS. I use the domain administrator to log into all the servers, and make the that domain administrator a local administrator. I've set up all the domain users for the CRM and gave them appropriate permissions, I have also added the accounts to the appropriate places, such that the CRM Deployment user is in the SQL security. The SQL Agent is running. SQL server configuration manager has SQL server network configuration TCP/IP enabled to allow remote connections. The SQL server has the domain user as a administrator, which is the same user being used to install the CRM. In the CRM setup i point to the [Servername]\[Instance] and I have also tried just the [Servername]. to make this easier I called the server MSSQL and left the instance name to the default. I even install the MSSQL instance as the domain administrator. CRM can find the ReportServer url. I have enable all the ports required, including: 135, 1433, 1434, 2382, 2383, 4022. 1434 UDP. I feel like I have absolutely done everything, I have google many times and tried all the different methods, and for the life of me I cant seem to get the CRM setup to find the SQL server agent. It passes everything else perfectly fine. I can even ping the MSSQL server. What is the problem, why does the CRM still keep giving the error: SQLSERVERAGENT (SQLSERVERAGENT) service is not running on the server MSSQL On the MSSQL server, the name of the sql server agent service is: SQL Server Agent (MSSQLSERVER)

    Read the article

  • Setting up a GIt server

    - by lindenb
    Hi all, My team is working with several RedHat linux servers and we'd like to synchronize our sources from one server to another (for several distinct projects). I'd like to set-up a git-server as a version control; however I'm new to git and I'm confused by the terms ('server', "daemon', 'repository', etc...). Moreover we're working behind a firewall. Can anyone point me to a link about how to setup a git server ? Thanks. Pierre

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >