Search Results

Search found 6545 results on 262 pages for 'usb hub'.

Page 4/262 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Installing Ubuntu to a USB drive

  - by Carl Smotricz

  I'm having a rough time getting Ubuntu to run from a 250 GB USB hard drive. I booted Ubuntu 9.10 from a CD and ran the regular "install" to the attached USB drive. I used the "advanced" option on the drive partition question to put the boot loader on /dev/sdb (the USB disk) but when I boot the machine it doesn't recognize there's a boot loader on the USB drive (it offers to boot from 2 other devices but not the USB disk). I also tried booting from the Ubuntu CD and using usb-creator-gtk to set up the USB drive. Seems to me this is meant to work with flash drives. I got a bootable USB disk but it looked and worked like the CD, i.e. it gave me options of "live CD" operation, installing, memtest, etc. That's not the way I want to run the system. Some help in installing Ubuntu, bootable into a "full" running system on my USB drive would be appreciated.

  Read the article

• How can I hard reset a USB device?

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on superuser.com as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

• External USB 3 drive not recognized

  - by ilan123

  Ubuntu 12.10 64 bit seems not to recognize my external hard disk. It is a Vantec NST-310S3 external disk enclosure with a WD 3TB drive. The disk has two NTFS partitions. My PC is a dual boot system. Under Windows 7 the hard disk works fine but I can't make it work with Ubuntu. When the drive is connected to the PC then the command sudo fdisk -l seems to hang forever. Below are the output of lsusb and cat /proc/partitions without the external drive and then with it connected. I added also the last lines of the dmesg command at the end. First without the drive: ilan@linux:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 13ba:0017 Unknown PS/2 Keyboard+Mouse Adapter Bus 001 Device 004: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Bus 001 Device 005: ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ilan@linux:~$ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 629043200 sda2 8 3 367001600 sda3 8 4 1 sda4 8 5 471859200 sda5 8 6 157286400 sda6 8 7 324115456 sda7 8 8 4101120 sda8 11 0 1048575 sr0 Second with the USB 3 drive: ilan@linux:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 13ba:0017 Unknown PS/2 Keyboard+Mouse Adapter Bus 001 Device 004: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Bus 001 Device 005: ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ilan@linux:~$ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 629043200 sda2 8 3 367001600 sda3 8 4 1 sda4 8 5 471859200 sda5 8 6 157286400 sda6 8 7 324115456 sda7 8 8 4101120 sda8 11 0 1048575 sr0 8 16 2930266584 sdb ilan@linux:~$ lsusb -v -s 004:002 Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. Couldn't open device, some information will be missing Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 9 idVendor 0x174c ASMedia Technology Inc. idProduct 0x55aa bcdDevice 1.00 iManufacturer 2 iProduct 3 iSerial 1 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 44 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk-Only iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 ilan@linux:~$ sudo fdisk -l [sudo] password for ilan: Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf1b4f1ee Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 1258293247 629043200 7 HPFS/NTFS/exFAT /dev/sda3 1258293248 1992296447 367001600 7 HPFS/NTFS/exFAT /dev/sda4 1992298494 3907028991 957365249 f W95 Ext'd (LBA) /dev/sda5 1992298496 2936016895 471859200 7 HPFS/NTFS/exFAT /dev/sda6 2936018944 3250591743 157286400 7 HPFS/NTFS/exFAT /dev/sda7 3250593792 3898824703 324115456 83 Linux /dev/sda8 3898826752 3907028991 4101120 82 Linux swap / Solaris dmesg output after connecting the external drive: [ 23.740567] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 23.740786] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 49.144673] usb 4-1: >new SuperSpeed USB device number 2 using xhci_hcd [ 49.163039] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 49.166789] usb 4-1: >New USB device found, idVendor=174c, idProduct=55aa [ 49.166793] usb 4-1: >New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 49.166796] usb 4-1: >Product: AS2105 [ 49.166799] usb 4-1: >Manufacturer: ASMedia [ 49.166801] usb 4-1: >SerialNumber: 0123456789ABCDEF [ 49.206372] usbcore: registered new interface driver uas [ 49.228891] Initializing USB Mass Storage driver... [ 49.229042] scsi6 : usb-storage 4-1:1.0 [ 49.229115] usbcore: registered new interface driver usb-storage [ 49.229116] USB Mass Storage support registered. [ 64.045528] scsi 6:0:0:0: >Direct-Access WDC WD30 EZRX-00MMMB0 80.0 PQ: 0 ANSI: 0 [ 64.046224] sd 6:0:0:0: >Attached scsi generic sg2 type 0 [ 64.046881] sd 6:0:0:0: >[sdb] Very big device. Trying to use READ CAPACITY(16). [ 64.047610] sd 6:0:0:0: >[sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) [ 64.048368] sd 6:0:0:0: >[sdb] Write Protect is off [ 64.048373] sd 6:0:0:0: >[sdb] Mode Sense: 23 00 00 00 [ 64.048984] sd 6:0:0:0: >[sdb] No Caching mode page present [ 64.048987] sd 6:0:0:0: >[sdb] Assuming drive cache: write through [ 64.049297] sd 6:0:0:0: >[sdb] Very big device. Trying to use READ CAPACITY(16). [ 64.050942] sd 6:0:0:0: >[sdb] No Caching mode page present [ 64.050944] sd 6:0:0:0: >[sdb] Assuming drive cache: write through [ 94.245006] usb 4-1: >reset SuperSpeed USB device number 2 using xhci_hcd [ 94.262553] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 94.263805] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c00 [ 94.263808] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c40 [ 125.262722] usb 4-1: >reset SuperSpeed USB device number 2 using xhci_hcd [ 125.280304] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 125.281511] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c00 [ 125.281516] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c40

  Read the article

• Choppy USB mice on just one of USB ports

  - by user20532

  I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

  Read the article

• Choppy USB mice on just one of USB ports

  - by user20532

  I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

  Read the article

• How to "restart/repair" an USB port?

  - by Click Ok

  My laptop has two USB ports, but one is broken, so I use a USB hub in the other good USB port. In that USB hub, I use a mouse and keyboard. Suddenly, that USB port doesn't detect the mouse and the keyboard (even with the light of the hub is on), and the only solution that I found is restarting the laptop. But just some minutes and the keyboard and mouse goes undetected again... Is there some method, software, etc. to "restart/repair" the USB port without restarting the PC?

  Read the article

• Can USB Hubs affect peripheral performance?

  - by Daniel Rasmussen

  Like many laptops, mine has 2 USB 2.0 ports. I'm looking to purchase a USB hub for my peripheral devices. I'm also planning on purchasing a laptop cooler with two USB powered fans, which connects to a USB port but can extend the plug, so it doesn't use one up. (Sorry for the poor description; see the link for a picture.) My questions are these: Can one plug 'too many' peripherals into a USB port? Can I plug my fans into a port, then the hub into the fans, then my keyboard and mouse, mic, and webcam into the extender..? Is it possible to draw too much power from a port? Secondly, will a USB hub affect the performance of any of my devices? I'm mostly worried about my mouse and keyboard. I like wired mice because I've noticed some lag in my Bluetooth mouse.

  Read the article

• Does a USB hub affect performance?

  - by user1018733

  I have two devices I want maximum throughput and latency with. (Midi drums and midi keyboard for example) Would connecting both to the same USB port via a hub effectively limit the maximum data transfer rate to 1/2 to each of them? I am assuming yes, but I didn't know if USB hubs had a handshaking and priority giving protocol available (e.g. let the device with the longer built up buffer of data communicate first) Thanks

  Read the article

• Lenovo W520 back usb port not working

  - by jaudette

  The usb port in the back of my laptop (on the right side when viewed from using perspective) is not working. Does anybody know if we can get this port working, and what the port number is. Here is my lsusb, if it can help. % lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 003 Device 002: ID 046d:c01e Logitech, Inc. MX518 Optical Mouse Bus 003 Device 003: ID 046d:c318 Logitech, Inc. Illuminated Keyboard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0765:5001 X-Rite, Inc. Huey PRO Colorimeter Bus 001 Device 004: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 005: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 006: ID 04f2:b217 Chicony Electronics Co., Ltd Lenovo Integrated Camera (0.3MP) Bus 002 Device 003: ID 17ef:1003 Lenovo Integrated Smart Card Reader I am running 12.10, upgraded from 12.04 but it did not work either in 12.04. The two usb ports on the left work just fine. EDIT: I just updated my bios from 1.32 to 1.39, no change in behaviour. The port does not even power up my devices. EDIT 2: Booted up windows, and the port is working. I went into the device manager and looked at the USB settings. I found my USB drive on Port 2, Hub 3, i just don't know how that relates to the Bus and Device numbers of linux. In windows, Smart card reader was on USB hub located at port 1 hub 2, fingerprint and bluetooth were on USB hub located at port 1 hub 1 EDIT 3: Went and looked at this SO post. Tried to look at my kern.log file with tail -f /var/log/kern.log. Got some activity when plugging/removing devices in other ports, but nothing happens when connecting a device into that port. It really looks disabled. Looked at my usb1-4 sys/bus/usb/devices/usb1/power/control and they are all set on auto. As expected, usb4 have version 3.00, the others (usb1-usb3) are 2.00.

  Read the article

• USB modeswitch to mass storage device

  - by Andrew

  I'm trying to install a Sierra AirCard 320U (branded as "Telstra USB 4G") into a VirtualBox Windows XP machine, on an Ubuntu 10.10 host. usb_modeswitch offers me a way to disable the "mass storage device" option, but I can't see a way to permanently re-enable it so it's usable by VirtualBox (device filters briefly detect it but then it disappears again). lsusb shows the device as: 0f3d:68aa Airprime, Incorporated When I first insert the device, it shows as 1199:0fff Sierra Wireless, Inc. Is there any way to re-enable the storage device so VirtualBox can see it?

  Read the article

• Ubuntu 10.10 USB drive not showing

  - by Ben

  USB is detecting but not showing the drives or mount details. Nothing there inside my /media folder and /mnt folder. I already enabled automatic mount and give privilege to user also. My sudo fdisk -l shows like: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d3ba7 Device Boot Start End Blocks Id System /dev/sda1 * 1 29637 238053376 83 Linux /dev/sda2 29637 30402 6142977 5 Extended /dev/sda5 29637 30402 6142976 82 Linux swap / Solaris Any idea?

  Read the article

• Logitech USB headset not working on 12.04

  - by thepeoplescoder

  I've looked around for answers to this question, But none of them seem to work for my particular problem. Obviously my USB headset isn't working, But I might as well share the scenario. I am running Ubuntu 12.04 and I have a Logitech USB headset. The relevant output from dmesg is as follows: [160708.528047] usb 2-1.2: USB disconnect, device number 9 [160768.890123] usb 2-1.2: new full-speed USB device number 10 using ehci_hcd [160768.997578] input: Logitech Logitech USB Headset as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.3/input/input15 [160768.997795] generic-usb 0003:046D:0A0C.0005: input,hidraw0: USB HID v1.00 Device [Logitech Logitech USB Headset] on usb-0000:00:1d.0-1.2/input3 When I go to System Settings - Sound, My headset shows up in both the Output and Input tabs, It is called "Clear Chat Comfort USB Headset" in those tabs, But I doubt that's a serious issue. When I click my headset in either tab to use it, The changes are not remembered when I reopen the sound settings, the built-in audio is still used. Also when I select the headset in the Output tab, and click the Test Sound button to test everything, The sound still comes from my laptop's onboard audio, instead of from my USB headset. Does anyone know how to correct this? I am stumped.

  Read the article

• USB mass storage couldn't get mounted

  - by revo

  It's my android phone SD card which was indicated damaged by android yesterday night, out of the blue! I put it directly to a USB port with a USB SD card holder case, so in that way I can recover it with TestDisk, which I had experienced before on a similar situation. I also noticed that there is a change in file system and capacity: File System : RAW Capacity : 0 (unknown capacity) Also TestDisk doesn't show it on its partitions list. A 2 GB SD card is not that important in price but I've a lot of files and medias which I need them. Used a mini card reader, TestDisk displayed it on its list but a quick search and or a deep search doesn't have any results No partition found or selected for recovery and then I should quit the program. Your help is appreciated. Update #2 lsusb output: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 002: ID 04f3:0234 Elan Microelectronics Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 007 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

  - by SuperUserMan

  Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

  Read the article

• Booting from USB on Mac Air (using setup_mac_usb_boot.sh)

  - by Mike O

  So, I've been working on this for hours and it's getting a little tiring. As some of you may know, installing Ubuntu on Macs is frequently an adventure, and I'm experiencing that right now. The part I'm hung up on at the moment is making a bootable USB. I would just use a CD, but my laptop is a MacBook Air (which doesn't have a CD drive), and I don't own an external CD drive. I initially attempted to use the command line method supplied by the Ubuntu documentation here: https://help.ubuntu.com/community/How%20to%20install%20Ubuntu%20on%20MacBook%20using%20USB%20Stick However, that wasn't even recognized by rEFIt even when I made a number of different modifications to the process, so I quickly decided to look elsewhere. I came across this guide: https://help.ubuntu.com/community/MacBookAir4-2#Basic_Installation_Instructions This ended up working to a large extent. If I choose the supplied grub from rEFIt, it will bring me to the Ubuntu grub, asking me to try it, install, or check the disk. And if I choose to boot Linux directly from rEFIt, it will bring me to the language selection menu. But when I make my selection from either of these menus it pauses for about ten seconds and then gives me a command line error message. It begins with kernel panic - not syncing timer doesn't work through interrupt, and then shows about eight file names. Does anyone here have any ideas as to what can be causing this? I also tried the script with both Ubuntu 11.10 (the current version when the script was written) and 12.04.

  Read the article

• USB Flash not recognised by Windows and BIOS, but works fine in Linux

  - by bbalegere

  I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

  Read the article

• wifi usb dongle detected but no wlan interface

  - by piotrek

  I'm using ubuntu 12.04. When I insert my philips PTA01 usb wifi dongle, in dmesg i can see: [ 1181.535290] usb 2-3: new high-speed USB device number 4 using ehci_hcd [ 1181.684074] usb 2-3: New USB device found, idVendor=0471, idProduct=209e [ 1181.684086] usb 2-3: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 1181.684093] usb 2-3: Product: PTA-01 [ 1181.684100] usb 2-3: Manufacturer: PHILIPS TV [ 1181.684105] usb 2-3: SerialNumber: 10 dmesg | grep ath: [ 367.861626] usbcore: registered new interface driver ath9k_htc but still there is no wlan interface when I do ifconfig. Just eth0 and lo. How can I turn wifi on? in case it's relevant. uname -a: Linux myhost 3.5.0-28-generic #48~precise1-Ubuntu SMP Wed Apr 24 21:42:24 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• CRM@Oracle Series: Showcasing Innovation with Oracle Customer Hub

  - by tony.berk

  When is having too many customers a challenge? It is not something too many people would complain about. But from a data perspective, one challenge is to keep each customer's data consistent across multiple enterprise systems such as CRM, ERP, and all of your other related applications. Buckle your seat belts, we are going a bit technical today... If you have ever tried it, you know it isn't easy. If you haven't, don't go there alone! Customer data integration projects are challenging and, depending on the environment, require sharp, innovative people to succeed. Want to hear from some guys who have done it and succeeded? Here is an interview with Dan Lanir and Afzal Asif from Oracle's Applications IT CRM Systems group on implementing Oracle Customer Hub and innovation. For more interesting discussions on innovation, check out the Oracle Innovation Showcase.

  Read the article

• DVC101 Video Capture Device on USB hub - Ubuntu Server 12.04

  - by John

  I have a Dell Inspiron 8600 laptop I use as a media server/video capture system. It only has 2 USB ports and I have a total of 3 devices I need to connect. The DVC101 works perfectly while plugged directly into the USB port in back of the laptop. Unfortunately it does not get recognized when plugged into a passive or powered USB hub. Questions: Is there something I am missing on the Ubuntu side? Something I need to do that will allow the device to be recognized through the hub? If not, will the extra USB ports on a dell laptop dock (port replicator) act the same as the aftermarket hubs? I know this one is off topic of Ubuntu but any input appreciated.

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

• Emulate a USB port as a USB flash drive?

  - by Wilco

  Does anyone know of any software that can emulate a USB flash drive through an available USB port in OS X? Perhaps some way to map a directory to a USB port that could then be connected to another device that supports reading USB storage devices? I'd love to connect my laptop to my car's USB port and access files as if it were a USB drive. I know about the target disk mode with firewire (not sure if this is also supported over USB), but I was hoping for something that doesn't require booting outside of the OS (I want to retain use of the machine). Any ideas?

  Read the article

• Davicom DM9601 USB LAN NIC Ubuntu 11.10 issue

  - by Gaurav_Java

  I have a davicom dm9601 USB ethernet card. When I plug in the device, it is detected and drivers are loaded, but I can't connect to internet using it. It works perfectly on XP, other laptop but not working on Ubuntu 11.10 How can I install the driver for this? I have tried many things But nothing is working. If I go to this link driver but not compiling or may I be doing something wrong. I found this one but don't know how to follow these steps . This is my lsusb output: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 064e:a103 Suyin Corp. Acer/HP Integrated Webcam [CN0314] Bus 003 Device 002: ID 08ff:1600 AuthenTec, Inc. AES1600 Bus 005 Device 002: ID 0a46:9601 Davicom Semiconductor, Inc. DM9601 Fast Ethernet Adapter Bus 006 Device 002: ID 046d:c045 Logitech, Inc. Optical Mouse Bus 003 Device 003: ID 0a5c:2101 Broadcom Corp. Bluetooth Controller Bus 004 Device 002: ID 04d9:1702 Holtek Semiconductor, Inc. But when I connected my Internet from different system its start working.

  Read the article

• USB Keyboard doesn't work in Ubuntu 14.04

  - by Steven Crossan

  My USB keyboard isn't working in Ubuntu 14.04, but also didn't work in 13.10. I upgraded today in the hope that the issue would be resolved, but it wasn't. The keyboard works in BIOS and GRUB but stops working when I reach the login screen. It is detected by the system, but just doesn't work. Output of lsusb: Bus 002 Device 002: ID 0846:9011 NetGear, Inc. WNDA3100v2 802.11abgn [Broadcom BCM4323] Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 1532:000d Razer USA, Ltd Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 002: ID 060b:2231 Solid Year KSK-6001 UELX Keyboard Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub I added: hid usbhid hid_generic ohci_pci To /etc/initramfs-tools/modules and did update-initramfs -u, but that didn't work. I'm new to Ubuntu/Linux and any help you could provide would be greatly appreciated!

  Read the article

• Problem installing Cardbus/PCMCIA drivers (USB 2.0 2-port)

  - by Carl

  I obtained the drivers from the manufacturer for my HT-Link NEC USB 2.0 2-port Cardbus card. When I plugged in the card before I got the drivers, 3 new entries showed up in the Device Manager - two "NEC PCI to USB Open Host Controller" and one "Standard Enhanced PCI to USB Host controller." With the card plugged in, I uninstalled those two drivers. I then removed the card. I copied the new drivers to c:\windows\system32\drivers and the .inf file to c:\windows\inf. I also copied the drivers & inf to a new directory called c:\windows\drivers\ousb2. I reinserted the card. Windows automatically installed the same drivers as before. I selected 'update driver' on the "NEC PCI to USB..." entry and didn't see any other options. I then selected 'have disk' and pointed to c:\windows\drivers\ousb2 and got a message "The specified location does not contain information about your hardware." I then selected 'update driver' on the "Standard Enhanced PCI to USB...," and manually selected "USB 2.0 Enhanced Host Controller" (OWC 4/15/2003 2.1.3.1). Windows then automatically found a USB root hub, and I manually selected "USB 2.0 Root Hub Device" (OWC 4/15/2003 2.1.3.1). Now there are two sections in the Device Manager titled "Universal Serial Bus controllers." I plugged in my external USB hard disk adapter, and "USB Mass Storage Device" was added to the first set. Here's how it looks (w/drivers from the properties): [Universal Serial Bus controllers] Intel(R) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD (6/1/2002 5.1.2600.0) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) USB Mass Storage Device USB Root Hub (7/1/2001 5.1.2600.5512) (5 more USB Root Hubs - same driver) [Universal Serial Bus controllers] USB 2.0 Enhanced Host Controller (OWC 4/15/2003 2.1.3.1) USB 2.0 Root Hub Device (OWC 4/15/2003 2.1.3.1) When I unplug the card the two "NEC PCI to USB..." entries in the first set disappear, and the whole second set disappears. (I unplugged the hard disk adapter first...) The hard disk adapter still doesn't work in that Cardbus card with the new drivers. I don't think the above looks right - a second set of USB controllers listed in the Device Manager, and the NEC entries still in the first set, and the the USB mass storage device still in the first set. Any help appreciated. (Windows XP PRO SP3 w/all current updates.)

  Read the article

• Device Manager - does USB listing look right?

  - by Carl

  I obtained the drivers from the manufacturer for my HT-Link NEC USB 2.0 2-port Cardbus card. When I plugged in the card before I got the drivers, 3 new entries showed up in the Device Manager - two "NEC PCI to USB Open Host Controller" and one "Standard Enhanced PCI to USB Host controller." With the card plugged in, I uninstalled those two drivers. I then removed the card. I copied the new drivers to c:\windows\system32\drivers and the .inf file to c:\windows\inf. I also copied the drivers & inf to a new directory called c:\windows\drivers\ousb2. I reinserted the card. Windows automatically installed the same drivers as before. I selected 'update driver' on the "NEC PCI to USB..." entry and didn't see any other options. I then selected 'have disk' and pointed to c:\windows\drivers\ousb2 and got a message "The specified location does not contain information about your hardware." I then selected 'update driver' on the "Standard Enhanced PCI to USB...," and manually selected "USB 2.0 Enhanced Host Controller" (OWC 4/15/2003 2.1.3.1). Windows then automatically found a USB root hub, and I manually selected "USB 2.0 Root Hub Device" (OWC 4/15/2003 2.1.3.1). Now there are two sections in the Device Manager titled "Universal Serial Bus controllers." I plugged in my external USB hard disk adapter, and "USB Mass Storage Device" was added to the first set. Here's how it looks (w/drivers from the properties): [Universal Serial Bus controllers] Intel(R) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD (6/1/2002 5.1.2600.0) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) USB Mass Storage Device USB Root Hub (7/1/2001 5.1.2600.5512) (5 more USB Root Hubs - same driver) [Universal Serial Bus controllers] USB 2.0 Enhanced Host Controller (OWC 4/15/2003 2.1.3.1) USB 2.0 Root Hub Device (OWC 4/15/2003 2.1.3.1) When I unplug the card the two "NEC PCI to USB..." entries in the first set disappear, and the whole second set disappears. (I unplugged the hard disk adapter first...) The hard disk adapter still doesn't work in that Cardbus card with the new drivers. I don't think the above looks right - a second set of USB controllers listed in the Device Manager, and the NEC entries still in the first set, and the the USB mass storage device still in the first set. Any help appreciated. (Windows XP PRO SP3 w/all current updates.)

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >