Search Results

Search found 4224 results on 169 pages for 'wireless n'.

Page 4/169 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How do I create a WiFi hotspot sharing wireless internet connection (single adapter)?

  - by Ruppesh Nalwaya

  I know how to create a hotspot when connected to a wired network, but when I am using internet from a WiFi connection, this disconnects the wireless connection the moment I activate the hotspot. In Windows I can use Connectify Hotspot, which enables me to share the internet connection from the same wireless adapter as I am creating an access point on. As you can read on the technology overview page: Access Point mode allows you to create a hotspot using the same Wi-Fi card that you are using to access the Internet. How do I do this on Ubuntu?

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Configuring two nearby WLANs: should I use the same ssid?

  - by Rory

  I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

  Read the article

• Configuring home wireless network

  - by dvanaria

  I'm new to setting up a home wireless network. I have Comcast tv/internet/phone service (modem included) as well as a wireless router. My question is pretty basic. How can I tell the performance of the following parts of the network? 1. incoming internet speed 2. speed of the modem 3. speed of the wireless router I basically want as fast an internet connection as possible, of course, but I'm not sure where to look for the bottleneck (and so, not sure where I can spend some money to speed things up). Right now I'm getting about 36 Mbps (as it shows in Windows). If I run an online speed test (xfinity has one) it shows Average download speed of 14.91 Mbps and Average upload speed of 5.72 Mbps. Thanks for your help.

  Read the article

• Atheros AR9285 / Lenovo G560 wireless not working after installing 13.04

  - by teyi

  I had Ubuntu 12.04 initially installed on my laptop. I upgraded to 12.10 then 13.04. Everything worked fine, including wireless. After adding a new memory card ( I only had 2 gb and one memory slot free) my wireess stopped working. I backed up all my data and reinstallled Ubuntu 13.04. Everything works fine except wireess. I bought this laptop in 2010 from Japan. It has Intel Core i5 CPU M 450 @2.40 Ghz * 4 3,7 Gb RAM os type 64 bit The output of iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off The output of rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no The output of lshw -C network: *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:7d:fe:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d6400000-d640ffff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:2b:36:ac size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff The wi-fi network appears as disconnected ( it's greyed out) Strangely enough I see a wifi network ( not mine) but not mine or the rest. That network doesn't require a password . I click on it, try to connect and i get an error message: failed to connect to xxxxx ... 32) The access point/org/freedesktop/NetworkManager/AccessPoint/0 was not in the scan list. Someone help please

  Read the article

• wireless network with cable modem and access point

  - by hayri

  I have a Scientific Atlanta EPC2203 cable modem and a TP-Link TL-WA500G access point. When I connect my computer directly to modem with a CAT5e cable I have internet connection on my laptop (when i type ipconfig i see my external ip there, provided by isp). So I decided to have wireless network in the flat, allowing other devices to connect as well. I bought this wireless ap (TL-WA500G) configured Wireless security stuff, and connected it to my modem. With that configuration (by default AP has static ip of 192.168.1.254) only my computer can connect to internet over wifi, but not any other device. When I set the IP of AP to Dynamic IP (DHCP) it is the same. How should I change my configuration to enable all wifi devices to connect to internet?

  Read the article

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• windows 7 wireless knocks off other computers on the network

  - by Sean

  I am trying to fix a wireless network issue. When a new windows 7 machine (we have 2 in the house) we have problems with any other windows xp machines connecting to the wireless network. I am using a linksys WRT110 running Firmware Version: 1.0.04 (which is not the latest firmware its Ver.1.0.07 but the router would not use the bin update file). I have tried a ton of variations in setting for the wireless network, changed the channel, the security level (none, wep wpa, wpa2), network type (g,bg mixed). I have also read some stuff about homegroup settings for windows 7 but have not seen any differences that make a difference. Basically windows 7 does not like to connect to our network but when I manage to get it to work the windows xp pro machines get kicked off. The windows xp pro machines are a few years old but both windows 7 machines are less than 6 months old.

  Read the article

• My wireless is hard-blocked

  - by Cristian

  I'm new to linux and i am having trouble getting my wireless to work I've found the following things Wireless LAN Soft blocked: no Hard blocked: yes and : *-network DISABLED description: Wireless interface product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 6c:62:6d:19:38:b9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-25-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:fdfe0000-fdfefff Can you please tell me what to do?

  Read the article

• Suggestions for wireless adapter

  - by Michael Kniskern

  I recently purchased a desktop computer and it did not come with a wireless network card. I am currently using the Belkin Wireless G USB Adapter and it is a very sub par product. It has very slow response times and download speeds with just basic browsing and downloads podcasts through iTunes. Does anyone have a better suggestion for a wireless adapter? Should I go with another USB adapter or one that connects directly into the motherboard? I am current using Windows Vista 64 bit Home Premium.

  Read the article

• Wireless internet sharing stops working after client disconnects

  - by Mandy

  I'm running Unbuntu 11.10 with the latest service packs, sharing an ether connection over wireless. Everything works fine, up to the point that the client (a laptop) sleeps or otherwise disconnects. The wireless connection at that point no longer functions, not showing up when searching for the hotspot with the laptop. The only way to recover is to reboot the machine, or toggle the wireless share off/on. I've double checked the wireless card has power management off. Currently what I'm doing is keeping an Ipod plugged into the box 24/7 to keep the wireless connection up when the laptop disconnects. I've searched the internet far and wide, found many issues with wireless problems after an ubuntu box itself sleeps, but nothing directly related to my problem. Hoping someone has some idea of where to look and what to check. A girl needs her Ipod back!

  Read the article

• Wireless does not work anymore after software update with Ubuntu 12.10 on a Dell Latitude E6230

  - by Andy

  I just installed Ubuntu 12.10 on my DELL Latitude E6230, on first boot wifi worked properly but when I updated the software it stopped working. I can't figure out the problem... The wireless network controller is a Broadcom Corporation BCM4313 802.11b/g/n Wireless Lan Controller (rev 01) "lshw -class network" gives, for the above controller: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7d00000-f7d03fff After reading the answer to another similar question, I edited the file NetworkManager.conf to make "managed=true", but that did not make any difference, it is as if the wireless adapter were not there. In the "Network" setting window, I only see "Wired" and "Network proxy". Wireless has just disappeared: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no and that's it! Nothing about the wireless controller... Any suggestions?

  Read the article

• Atheros AR5BWB222 Wireless Intermittent Connectivity

  - by Bart

  So I recently installed Ubuntu on my Acer Aspire V3-551 laptop. I have an Atheros AR5BWB222 wireless adapter. Everything works fine except for the wireless. I can sometimes connect to the wireless, but most of the time it will be making an attempt to connect and then enver connect. Or it will connect, but it will only stay connected for about 10 seconds before getting disconnected from the wireless. All the other drivers updated through System SettingsAdditional Drivers are fine, even the Ethernet. Its just the problem with the wireless. I've tried a power managment setting, tried looking for additional updates, but nothing fixes my problem. Is there any solution for my particular wireless card?

  Read the article

• Wireless problems on HP

  - by Sat93

  I'm not able to enable Wireless using the hardware switch on my HP ProBook4430s. Because of this the Enable Wireless option is greyd out and I cannot enable it. The greyd out option can be seen in the screenshot below. The results of iwconfig for my system are as follows, lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. Also I tried to do the following, sudo ifconfig wlan0 up but I got an error as below, SIOCSIFFLAGS: Operation not possible due to RF-kill Also the result of sudo rfkill list all for my system is as follows, 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no How do I fix this problem? Thanku!

  Read the article

• Programtically get the Wireless lan config of a machine and use netsh to setup new profile

  - by Maestro1024

  Programtically get the Wireless lan config of a machine and use netsh to setup new profile I am having trouble getting the netsh command to set the ssid of a new card. I installed the drivers and plugged it in. I see in ipconfig it says the "media is disconnected" (fair enough). I then send the following command netsh wlan connect name=profile1 ssid=myNetwork interface="Wireless Network Connection 2" problem is I get an error "There is no profile "profile1" assigned to the specified interface. What is a profile for a wireless card? What should I set it to? How Can I get my SSID set and connected for the card.

  Read the article

• D-Link DWA-125 Wireless network card not working after upgrade from 10.04 to 12.04

  - by dava2788

  I upgraded to Ubuntu 12.04 and now the wireless network card D-Link DWA-125 doesn't work. I have the drivers from the official website, But neither recognized during installation. iwconfig: lo no wireless extensions. vmnet8 no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. vmnet1 no wireless extensions. dava@Dava-Ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 006: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT3070] And the chipset: ralink 2870/3070 (rt3070)

  Read the article

• cannot connect to wireless network on ubuntu 12.04

  - by angjinhang

  i have installed ubuntu on my 6-year-old Acer Aspire 4310 and i love it's lightning speed.but, now i have a big problem, that is it cannot connect to any wireless network. the wireless network worked well in my windows. the wireless switch is not responding to me(i guess it only works on windows). there are also no wireless toggle switch on my keyboard. i have installed my driver, yeah, a proprietary driver. i installed it, and my i never see my wireless network anymore, even the enabling and disabling button in the system settings. i can connect my wireless network during the ubuntu installation. so what's the problem? i cannot find wlan0 in the ifconfig output. i can still see the enable and disable button in the system settings before i install the driver. now even i remove the driver, i will no longer display. i wanted my wifi back, help!

  Read the article

• No wireless adapter in msi u200

  - by Mino Marimat

  I have a MSi u200, and the weird thing was that I was using this normally before, then after a few minutes all of a sudden it couldn't find the wifi signal from my house. I did some troubleshooting and a bit of search in the control panel, and it seems like my hardware is missing. :( I can't even turn on the wireless light using Fn+F8, so my suspicions about the missing hardware strengthened. I tried searching for DIY fixes, but I found out that the wireless card is actually built-in deeper, unlike the RAM cards and the hard drive where you can either replace or add more cards. What do I do?? As of the moment, I can get connected to my wifi here at home using a wireless adapter via usb, and it's working. So my guess about the hardware problem seems correct. HELP!!! Thanks!

  Read the article

• forwarding packets from wireless nic wlan0 to another Wireless nic wlan1

  - by user179759

  I have two wireless interfaces wlan0, wlan1 I want wlan0 to be connected to the internet via a wireless router and I want wlan1 to be in AP mode acting as a router to give internet access to whoever connectes to it. So basically all packets coming through wlan1 should be forwarded to wlan0 = Router = Internet. That's including DNS/DHCP/etc.. [A]~~~~~(Wi-Fi)~~~~~~v [B]~~~~~(Wi-Fi)~~~> [me] ~~~~(Wi-Fi)~~~~~>[AP/Router]------->[internet] [C]~~~~~(Wi-Fi)~~~~~~^ Any idea how can I do this? ps: I tried using bridges but I always get 'operation not supported' using the brctl tool.

  Read the article

• Wireless Access Point - Can't ping other machines on the wireless network

  - by Surfer513

  I have a wireless access point (Netgear), and I have it setup so that it has an IP address in the current subnet (let's say 192.168.2.0, subnet mask of 255.255.255.0). The machine that it is connected to via ethernet cable has an IP in the same subnet as the AP. The machines that are connected to the AP via the wireless connection also have an IP address in the same subnet as the rest of the network (192.168.2.0). All machines can ping the access point, but they cannot ping each other. I don't totally understand why, because there is connection and all of the machines are in the same subnet. I realize this is a layer 3 device, but is there an issue because of this AP's lack of gateway capabilities? (i.e. no routing table, etc.)

  Read the article

• How To Get a Better Wireless Signal and Reduce Wireless Network Interference

  - by Chris Hoffman

  Like all sufficiently advanced technologies, Wi-Fi can feel like magic. But Wi-Fi isn’t magic – it’s radio waves. A variety of things can interfere with these radio waves, making your wireless connection weaker and more unreliable. The main keys to improving your wireless network’s signal are positioning your router properly — taking obstructions into account — and reducing interference from other wireless networks and household appliances. Image Credit: John Taylor on Flickr How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems 7 Ways To Free Up Hard Disk Space On Windows

  Read the article

• Display wireless channels currently in use

  - by DrStalker

  Is there any windows utility to display the wireless channels are currently in use by the available wireless networks? I'd like to be able to see what existing channels are using so I can try to minimize interference on a new access point without a lot of trial and error.

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• good PCI-e Wireless card for Windows7?

  - by benwebdev

  Hi I've just build a 64bit Windows 7 PC but am unhappy with the piddly performance of the linksys USB wireless dingle I've used. Can anyone suggest a good PCIe alternative that will be stronger for connection and maybe faster. I dont see why my desktop should show a weaker performance on wireless than my laptop when its sat next to it or even my Palm Pre for that matter. any thoughts? UK based max around £60ish. thanks, Ben

  Read the article

• hp pavilion g6 1250 with a BCM 4313 doesn't see any wireless networks

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation, ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) There are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >