Search Results

Search found 2370 results on 95 pages for 'av cable'.

Page 40/95 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

  • How to fix network connection dead on startup, but okay after disable/enable?

    - by bill weaver
    on Startup When my system starts up, the internet connection is dead. This causes various problems with startup items such as updates and auto-start programs failing. However, the connection is fine after going into Network and Sharing, Change adapter settings, then disabling and re-enabling the adapter. Any suggestions on why this is happening and how to fix it? System summary: Windows 7, 64 bit, Realtek PCIe GBE Family Controller, Linksys WRT610N router, Sci Atlanta cable modem.

    Read the article

  • Do i need to join Graphics Card with CPU fan

    - by Mirage
    Initially i had inno 3d 256MB Nvidia GTS graphics card. I also had another Big FAN above the processor (Vendor put in quad core) In that card there was one cable which was joined with that FAN. Now i have changed the CARD to 1GB Nvidia GT9600 . But there is no pins to join the fan with that card. Is it ok . i don't know why old card was joined with FAN

    Read the article

  • Internet Sharing via router

    - by mak4pi
    Question: How to setup Internet Sharing among two computers (one Mac 10.5.6, one Ubuntu 9.10) via a router? Situation: The Mac is using AirPort (wireless interface) to connect to router as 192.168.1.101. The Ubuntu is using an ethernet cable to connect to router as 192.168.1.104. Visual: Mac )))))) Router ======= Ubuntu Any ideas are greatly appreciated. Thanks.

    Read the article

  • Where can I buy a Stereo audio to 3.5mm adapter?

    - by iftrue
    I need a stereo (6.33mm) to PC audio (3.5mm) adapter, and I'd like it to have an inch or two of cable so that yanking the connector doesn't break the audio port the 3.5mm is plugged into. I used to own one of these, but I lost the adapter. Where can I buy something like this online? I can only find solid adapters or 25' cables.

    Read the article

  • Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

    - by user95917
    hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

    Read the article

  • internet disconnects

    - by Smokezzaj
    Internet disconnects and reconnects, computer is in a peer to peer workstation with two other computers XP o/s. Only one computer has this problem the other two don't disconnect. Computer's connect to switch no router is being used. Ipconfig shows a DHCP connection, local area connection status shows packets being sent out but packets are not being received or being received at a extremely slow rate. Tried Winstock tool, reinstalling network card driver, restored to previous date, checked ethernet cable and release/renew IP.

    Read the article

  • Sharing files between Mac Mini and Ubuntu

    - by Dan
    I want to get files off a Ubuntu box (10.04) and transfer them to a Mac Mini. I am connecting the two directly with a piece of network cable (Its not crossover, but I am told the Mini can handle this). The Ubuntu box has Samba installed(I think), but no internet connection. When I create a shared folder in Ubuntu it doest show up in Mac OS. But the Ubunutu box is appearing in the 'Shared' section in Mac Finder. Help

    Read the article

  • The device 'Microsoft DV Camera and VCR' could not be opened

    - by w35t
    I trying capture video from DV camera into computer with firewire cable. When I select "Capture Video", and then check DV, "Sony Video Capture 6.0" pop-up this error: The device 'Microsoft DV Camera and VCR' could not be opened Screenshot I use Sony Vegas Pro 8.0 and windows 7 ultimate x64. I tried many ways and they was not successful. Camera "Canon MV750i". Thanks. Sorry for my English.

    Read the article

  • Socket error sendig data from loftware to zebra zm400

    - by Mike
    I have a problem with my Zebra zm 400. I print a label from loftware, and in random times comes the label not out from the printer. When this issue comes, then I can't ping my printer or I can't achive the webpage of the printer. Only I need to disconnect the UTP cable from te Zebra. and after this disconnect work the printer fine. And in variale intervals come this problem again! Thanks and regards, Mike

    Read the article

  • Turn off laptop CD-ROM

    - by Stan
    Since I seldom use the built-in cd-rom, but usually carelessly press open door button which is on the side of laptop. Is there any way to power off cd-rom so the button won't work. Better not to open the back lid and unplug power cable.

    Read the article

  • Share 3G connection over WiFi-LAN network

    - by kush.impetus
    This is how I have established network between my PC and my laptop at home (being novice in networking, it took me few days to achieve the feat). And it is working perfectly. I can easily share files between them. Laptop IP Address: 192.168.1.4 Subnet mask: 255.255.255.0 Default Gateway: 192.168.1.2 Desktop IP Address: 192.168.1.5 Subnet mask: 255.255.255.0 Default Gateway: 192.168.1.2 ASUS RT-N10+ Router IP Address: 192.168.1.4 Default Gateway: 192.168.1.2 I have connected the Desktop PC to the router using a LAN cable, and laptop to router over WiFi. Both, PC and laptop are running on Windows 7 OS, are on same HomeGroup, have same username / password. Also, I have connected the Ethernet cable to LAN port 1 of the router. Click here to view a graphical representation of the network. Can't post image here, because I don't have 10 reputation points. Now, what I want is use connect to Internet using a 3G USB modem on one device and share it over the network on the other. I tried Huawei and Micromax 3G USB modem. Both obtain a new IP address whenever I connect to Internet (means they have dynamic IPs). Rest, both have Subnet Mask as 255.255.255.255 and Default Gateway as 0.0.0.0. In that case, I cannot directly share Internet from the modem. Preferred DNS is blank for now in both, laptop and PC. What I am planning to do is to connect to Internet on laptop using the 3G modem and share the Internet connection over laptop's Wi-Fi (as hotspot) using Connectify, which I have done already. That, I suppose, will broadcast a static IP to connect to. Now what I can't figure out is that what changes should I make to the network settings of the router and the PC so that PC connects to the Internet broadcast by Connectify? Is that possible on the first hand? Please note that I am trying to implement the network without spending anything extra (for purchasing as USB WiFi adapter for PC, of course, which could have made the life lot easier for me). Thanks in advance

    Read the article

  • Using a Blackberry Bold as an IP Modem on Windows 7

    - by Lawrence
    I recently installed Windows 7 and now cannot use my Blackberry Bold as a modem (via a USB cable): When I query the modem it is successful. I have added the correct "at" commands. When I try connect it says "connecting modems" but then it times out with the following error: Error 638: The remote server is not responding in a timely fashion. I also have the latest desktop manager software installed.

    Read the article

  • HP Pavilion DV6 doesn't recognize wireless networks

    - by Mike N.
    Okay so about a few weeks after I got my laptop the wifi would connect and disconnect, off and on. And every time I troubleshoot it, a message comes up saying there's a network cable not properly plugged in or broken... It's been doing this for about a year and I usually just tap the bottom of the laptop or something and the wifi connects again but now it refuses to turn back on, how do I fix this?

    Read the article

  • Is minimum latency fixed by the speed of light?

    - by JavaRocky
    Suppose i had a fiber optic link from one side of the planet to the other side of the planet. Is it safe to say, that with current technology, the latency of communication can never be reduced? Understand that a fiber optic cable is not a perfect medium thus data only travels close to the speed of light. Also lets consider that i will not be drilling a hole thru the center of the earth and it is just running along the ocean.

    Read the article

  • Why is SMB from a Windows 7 64-bit to OS X Server so slow when using DNS vs IP?

    - by chuboy
    When I connect my 64-bit Windows 7 to a OS X server using \servername, my transfer rates are around 400KB/s. However, when I do the same thing using \192.168.0.10 (which is the IP of the server), transfer rates jump to 30MB/s. All of this happens via a gigabit ethernet cable with my wireless disabled I heard Samba itself "doesn't use DNS", but if that's the case, how am I able to connect to the server in the first place?

    Read the article

  • Creating an ad-hoc wireles network on a router

    - by bo7ons
    My router is a Wag200g with openwag firmware. My laptop is connected to the university's internet through an ethernet cable and i have to set the browser proxy settings to connect. I want to create an ad-hoc network with a router so that i can let my laptop do the proxy routing/forwarding itself and that my android phone can connect to it and use my university's proxy (I've tried setting the proxy on my phone but it wont work).. Or am i approaching this the wrong way?

    Read the article

  • applescript: establish PPPoE connection

    - by user26700
    how would an Applescript look like that connects to a specific PPPoE configuration? i want to trigger this via Launchbar. (or a more fancy script which checks if the current chosen network location is the right one and if an ethernet cable is plugged in, then connect to the PPPoE service automatically. i'd be completely satisfied with the simpler version though)

    Read the article

  • Get 5.1 surround sound from computer through a VCR config?

    - by Wedding Nails
    I'm posting to see if my idea of this setup is right and can be done. I currently have the following "equipment": a JVC VCR -quite old-, which has built in surround sound (aka it has several speaker outputs, which I believe is 5.1 and are connected to several speakers that are in every corner of the room), a computer with SPDIF optical output and a new flat screen TV (with built in HDMI). I want the computer to take advantage of the VCR's surround system (all the speakers in the room) in order to play mainly music and video always with all the speakers (5.1) and with the maximum sound quality. Currently, the computer plays sound only through the front speaker (I connect one output to the on board pc audio input) and the quality is really bad. As a side note, the computer video runs with S-video (old school), and the picture quality as you would imagine, is really bad with the new big LCD screen. My main goals are: to upgrade the picture with a new video card which would support HDMI (my tv has HDMI). to buy a SPDIF optical cable, connect one end to the VCR SPDIF input and the other end to the PC output This is theoretically what I've researched so far, and I came out with several questions: in this case, with the SPDIF cable connected, and all the configurations done in windows allowing the 5.1, will I get every content I play "converted" or played through all of my speakers? (I read this forum post). I already know that in order for this setup to play from all the speakers, the content/audio source has to be 5.1. but my question is, if there is a way to play from all of the speakers no matter what type of content I'm playing (that's why I said conversion there) I already know that HDMI cables carry digital sound. Is there a way I can only use said HDMI cord to the tv, and get sound through the VCR? (I'm not too sure about this, I would have to disable the TVs speakers and use the VCR surround as default, but I have no clue wether this can be done or not). Update: The ultimate question is, do I really have to rely on "sound virtualization" technology to get sound from all the speakers, no matter what content I play? (do I require a newer sound card, like a creative soundblaster with said technology?) Thanks!

    Read the article

  • Burnt SATA Drive

    - by luvieere
    By stupid curiosity, I've connected the FDD power cable to the jumper pins of a SATA drive, and powered on the system. The SATA drive's controller burned out. What now? Can it be replaced, and still be able to read the disc?

    Read the article

  • Remote Router Access For Linksys WRT54GL

    - by Tim
    Hi, I just set up a wireless network at home using a Linksys WRT54GL. All was fine except that I can still access 192.168.1.1, the configuration setup page of the router, within the local wireless after I disabled "Remote Management". I think if remote access is indeed disabled, one can access my router setup page only by using a cable connecting from his computer to the router. Is this true or am I wrong? Thanks and regards!

    Read the article

  • Can I make my Linksys WAG200G as an access point?

    - by Adnan Badar
    I have two routers one is dsl router (connected through my fone line) second is Linksys WAG200G, i want to use this router as an access point to increase the signal strength in my neighborhood can anyone please guide me step by step as i am not that good in networking i need to know both ways one by connecting a cable from the first router to the second and then make access point to the second one. second by connecting wireless from the first router to the second and then make access point to the second one. Thanks. Adnan

    Read the article

  • Can I prevent tv-out from disconnecting when monitor sleeps?

    - by Damon
    I have my TV connected to my computer (windows 7) through an HDMI cable that also carries the sound. I like to put on music on my TV, but the problem is when my monitor goes to sleep back in my office, it switches off the hdmi connection completely and the audio goes back to my PC. I would like a way to stop this from happening without turning off sleep mode entirely. I have an ATi Radeon 5700

    Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >