Search Results

Search found 1522 results on 61 pages for 'caution continues'.

Page 40/61 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

  • Outlook certificate error and separate send/receive error

    - by Richard
    I run a laptop with Vista 32bit and MS Office 2010. Outlook has two profiles, both configured as POP3/SMTP and neither go through an exchange server. Recently, one of the mail servers (hosted with easily) was getting full, so I changed the profile setting to delete from the server if mails are older than 60 days. Suddenly, I am now experiencing a couple of glitches. The first is that I get a certificate error when outlook tries it's first send/receive under the relevant profile - "The server you are connected to is using a security certificate that cannot be verified" This continues despite apparently successfully re-importing the certificate. The second glitch is that I get a "Sending reported error (0x8004010F): 'Outlook data file cannot be accessed'" error on send receive. Strangely, it seems to be trying to send/receive twice - once to 'mail@domain', which works, and the second to 'domain' which doesn't. I've tried deleting the profile and re-creating it, pointing to the original .pst file, but still get both errors. Does anybody know how I can resolve these errors? (As a by note, and not that important, more for curiosity, does anybody know why simply changing the delete from server setting against that profile would cause these issues?)

    Read the article

  • Postfix qmgr process causes heavy overload on mailservers

    - by Mattias
    We are using Postfix as MTA for our e-mailmarketing software and once in a while we see that the load on one of the mailservers rises above 5. The load is caused by the qmgr-process which is the heart of Postfix and I see that it is consuming a lot of CPU resources. The process seems to be stuck because after 15 minutes it is still doing the samething and still increasing the load. Once I restart the postfix service the load rapidly decreases to below 1 and Postfix continues to send e-mails without any problems. I'm wondering if anyone else has encountered this problem and if people have suggestions on how to prevent it. The problem shows up on all our mailservers but almost never at more than 1 at the time. It seems to be triggered only when we are sending a mailing but the size (10 or 100.000 e-mails doesn't seem to make a difference). It maybe happens once a week or even less often and the time and day is also different every time. We tried to solve the problem by decreasing the amount of messages qmgr is allowed to process but this didn't solve it. We are using Postfix 2.5.5 on Debian Lenny 5.0.8 (postfix is installed through the default Debian repository). No special messages can be found in the logs (syslog, messages, mail.*). Thank you for your time

    Read the article

  • Logitech QuickCam Pro 9000 & Windows 7 64-bit failing miserably

    - by Saxtus
    I am trying to install a Logitech QuickCam Pro 9000 webcam to Windows 7 64-bit. If I do it without using the Logitech drivers but instead the Windows Update ones, the camera works with low frame rate and without face tracking and all other bells and whistles that it's full driver provides. The moment I install the latest official Logitech driver, the problems begin: Camera works fine, until I decide to go to audio settings of the LWS panel or Windows'. Then LWS freezes and with it everything that tries to output audio. I am not able to open Playback/Recording devices window (it just doesn't appear) and system gets unstable and slow with LWS.EXE process not been able to close forcefully. If I reboot and forget the camera connected, this situation continues and system gets unstable from the beginning. If I reboot without the camera connected, everything works fine until I connect it and try to do something with audio settings of Windows or LWS panel. I should note, that until the freezing occurs, camera works as expected, with full frame rate, face tracking and everything that is expected to do. The soundcard is the ASUS SupremeFX II of the ASUS Striker II Extreme motherboard. Any ideas of what is causing this or what else to try so I can make it work as advertised? Thank you.

    Read the article

  • Backup Exec 10 - Network connection to the remote agent has been lost

    - by jherlitz
    Okay, so I have 4 remote offices, all running off of a 3mb ethernet connection. Two sites are part of a WAN and 2 sites are using 3mb connections over a site to site tunnel. I am using Backup Exec 2010, I have the remote agent installed on all the remote servers. For the past few weeks now, on the two sites running over the site to site tunnel have been failing with the following error message now. "The network connection to the Backup Exec Remote Agent has been lost. Check for network errors" We used to be on a DSL connection site to site tunnel, now we changed to the 3mb ethernet connection using site to site tunnel. I have to find out, has it been failing ever since we changed, or just recently. Backup exec support is telling me it is a network issue. My communication or connection to the server is solid, we don't have any issues, or outages. So I am baffled on why this continues to fail. And why just those two sites.. Any advice?

    Read the article

  • Disable "Do you want to change the color scheme to improve performance?" warning

    - by William Lawn Stewart
    Sometimes this dialog box will pop up (see screenshot below). Every time it appears I select "Keep the current color scheme, and don't show this message again". Windows then reminds me again -- either the next day or after reboot, or sometimes another 5 minutes later. Do you want to change the color scheme to improve performance? Windows has detected your computer's performance is slow. This could be because there are not enough resources to run the Windows Aero color scheme. To improve performance, try changing the color scheme to Windows 7 Basic. Any change you make will be in effect until the next time you log on to Windows Change the color scheme to Windows 7 Basic Keep the current color scheme, but ask me again if my computer continues to perform slowly Keep the current color scheme, and don't show this message again Is there some reason why Windows is ignoring/forgetting my attempts to suppress the dialog? I'd love to never ever see it again, it's annoying, and it alt-tabs me out of fullscreen applications. If it matters, I'm running Windows 7 x64 Professional. I believe the dialog appears because I'm forcing Vsync and Triple Buffering for DirectX applications.

    Read the article

  • Juniper SSG 5 VPN

    - by Ethabelle
    I have a host who set up our Juniper SSG 5 VPN with Firmware version-6.2.0r5.0 I've been trying to set up VPN on it using this guide: http://kb.juniper.net/InfoCenter/index?page=content&id=KB4094 I've followed the steps and on my Mac, whenever I try to connect using L2TP over IPSec I get the following error; Summary of Steps: Create User (give them L2TP auth ability), Create Group, Place User in Group, Create VPN Gateway, Create VPN, create IP Pool, change default L2TP settings, create Untrust Trust Policy. The L2TP-VPN server did not respond. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I looked in my Firewall's logs, but I don't even see anything under Reports Logs Events. I'm.. obviously missing something, I just don't know what I'm missing at this point. I'm just starting networking and this is sort of Step 101 and I'm getting annoyed and just want to throw up OpenVPN, but I've read that has problems with Juniper Firewalls. Hooray.

    Read the article

  • I/O Error on LG GSA-H12N DVD drive on Windows 7

    - by Ashwin
    I am facing an I/O Error when I try to burn DVD data discs on my LG GSA-H12N DVD drive on Windows 7. Note that I was able to do this same operation on the same hardware/software just a day earlier without any problems, but with Windows XP. The only change (AFAIK) has been the installation of Windows 7 to replace Windows XP on this PC. Here is the error I get when I try to burn a DVD data disc using CDBurnerXP 4.2.7.1801: Burning error occured An error occured while burning the disc. Most likely the disc is not usable. Usually these errors happen if the inserted media is not compatible to the drive or of poor quality. (devNTSPTI_IO_Error) Could not write to Disc (LBA: 52864 Length: 32). SCSI Pass-through Interface I/O Error. - 0xFF045D Note that there can be no problem with the discs since I have been using the same discs (from the same box) just before the Windows 7 installation with no problems. The only change has been Windows 7. I tried InfraRecorder v0.5 and ImgBurn v2.5 and got similar I/O errors: Note that Windows 7 lists the LG GSA-H21N drive as being compatible (see this link). I also checked the LG Drivers website and using the firware update from there updated the drive firmware from version UL01 to UL02. But, even this has not helped. The drive reads DVDs without any problem, but continues to produce coasters. Could someone help me figure out what is the problem? Thanks :)

    Read the article

  • Debugging Windows PC freeze

    - by Violet Giraffe
    I have a problem with my computer, would appreciate any hints/ideas. It usually begins not immediately after booting Windows, but at some unpredictable point in time, which doesn't seem to correlate with any specific actions of mine. First sign of a problem is process System starting to consume 25% CPU time steadily. I have a quad-core CPU, so it might be one thread working non-stop. At this point micro-freezes start to occur - screen stops refreshing, but if I have, say, music player running - it continues playing. If I try to do something between the freezes, like open Start menu, it will freeze completely and forever. If I press reset button the PC will shut down and then start cold, as opposed to usual reset behavior (which doesn't include PC shutting down). I have noticed that full restart upon reset is usual for hardware problems, but I think this problem isn't related to at least motherboard-CPU-RAM-videoadapter. It certainly isn't caused by overheating. One very important not is that it seems to be related to Windows hosted WLAN network: I have USB Wi-Fi dongle and have configured a hosted network to share cable Internet connection with Wi-Fi devices. I am not 100% certain there's a strong connection, but in 9 or 10 cases when I enabled the network (by executing netsh wlan start hostednetwork), it did freeze eventually (sometimes within minutes of starting the network, sometimes within hours), and on at least 10 days when I didn't start the network it never froze, no matter how I used the computer). There are no critical/error entries in the events log that I can suspect as being related, only regular stuff like "driver not loaded". I have found no critical/error events that are being logged around the time of freeze occurring and are not logged during normal boot without starting the WLAN.

    Read the article

  • E-mail duplication problem

    - by Gavin Osborn
    I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

    Read the article

  • LG LW20 Express won't boot after hdd replace

    - by Mika
    My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

    Read the article

  • Setup Firefox to save .pages as .zip automatically

    - by Mike Dtrick
    What do I want to do? I would like Firefox to save files with the .pages extension as .zip files automatically. Scenario You are browsing through your emails and you notice your friend just sent you an email with a file attached (a .pages in this example). Unfortunately, you have a laptop that runs Windows. Your friend continues to send tons of emails with .pages files attached and you are tired of manually saving the files as a .zip file. Ultimately, you would like Firefox to be set up so that the download/file manager recognizes the .pages extension and automatically converts it to a .zip file. What have I done? I have saved files manually by selecting save as "All Files" and setting the extension to .zip. I've gone through Firefox and their documentation and have not found anything on how to complete this task. Why am I doing this? To save time (only a few seconds, not the main reason). I would like to setup a simple solution that "converts" a file automatically without having to recall steps on how to achieve the task manually (for clients who aren't exactly tech savvy). So that clients with Windows can access the files. IMPORTANT NOTE: I am not trying to save the web page, rather an Apple document equivalent to Microsoft Word. UPDATE: The really easy method would be to save one file, right click it, choose properties and open all .pages files up with WinRAR (or any other program that extracts files from a compressed folder). For the sake of learning, I am going to "neglect" this method and continue to do some research on Firefox add-ons. I would still like to have Firefox or the download manager to do the bulk of the work for converting the file.

    Read the article

  • outlook security alert after adding a second wireless access point to the network

    - by Mark
    Just added a Netgear WG103 Wireless Access Point in our conference room to allow visitors to access the internet through out internal network. When switched on visitors can connect to the intenet and everything works fine. Except, when the Access Point is switched on, normal users of the network get a Security Alert when they try to start Outlook 2007. The Security Alert is the same as the one shown in question 148526 asked by desiny back in June 2010 (http://serverfault.com/questions/148526/outlook-security-alert-following-exchange-2007-upgrade-to-sp2) rather than "autodiscover.ad.unc.edu" my security alert references our "Remote.server.org.uk". If I view the certificate it relates to "Netgear HTTPS:....", but the only Netgear equipment we have is the new Access Point installed in the conference room. If the Access Point is not switched on we do not get the Security Alert. At first I thought it was because we had selected "WPA-PSK & WPA2-PSK" Network Authentication Type but it continues to occur even if we opt for "Shared Key" WEP Data Encryption. I do not understand why adding a Netgear Wireless Access point would cause Outlook to issue a Security Alert when users try to read their email. Does anyone know what I have to do to get rid of the Security Alert? Thanks in advance for reading this and helping me out.

    Read the article

  • Windows 7 - Intermittently processes will not close when the app closes

    - by Bill Sambrone
    I have a user I am supporting who has the strangest issue. There are 2 problem applications, Word 2010 and a scanning program called ScandallPro. Intermittently (and at least once a day), she will close an app and the underlying process will not close. Both Word 2010 and this scanning software have all the latest updates. There is another user who has the same software that does not have this problem, and has identical hardware. I have formatted and rebuilt the computer for the user who is having the problems. After the rebuild, the machine was fine for a day but the scanning software continues to intermittently keep the process running even after it is closed. This is a problem because she cannot open a new instance of it while the process is still running. There is a boatload of line of business software on this machine, all of which she needs. I believe the Word 2010 issue is due to a misbehaving add-in (there are 2 add-ins, neither of which seem stable), and I think my best bet is to work with the add-in vendor on it. The scanning program staying open is isolated to this 1 user. The only difference between her machine and the other user is that she has Quickbooks, RoboForm, and Adobe Acrobat X Pro. Any ideas of what can be causing this, or other diagnostic steps to try?

    Read the article

  • How ZFS handles online replacement in a RAID-Z (theoretical)

    - by Kevin
    This is a somewhat theoretical question about ZFS and RAID-Z. I'll use a three disk single-parity array as an example for clarity, but the problem can be extended to any number of disks and any parity. Suppose we have disks A, B, and C in the pool, and that it is clean. Suppose now that we physically add disk D with the intention of replacing disk C, and that disk C is still functioning correctly and is only being replaced out of preventive maintenance. Some admins might just yank C and install D, which is a little more organized as devices need not change IDs - however this does leave the array degraded temporarily and so for this example suppose we install D without offlining or removing C. Solaris docs indicate that we can replace a disk without first offlining it, using a command such as: zpool replace pool C D This should cause a resilvering onto D. Let us say that resilvering proceeds "downwards" along a "cursor." (I don't know the actual terminology used in the internal implementation.) Suppose now that midways through the resilvering, disk A fails. In theory, this should be recoverable, as above the cursor B and D contain sufficient parity and below the cursor B and C contain sufficient parity. However, whether or not this is actually recoverable depnds upon internal design decisions in ZFS which I am not aware of (and which the manual doesn't say in certain terms). If ZFS continues to send writes to C below the cursor, then we are fine. If, however, ZFS internally treats C as though it were gone, resilvering D only from parity between A and B and only writing A and B below the cursor, then we're toast. Some experimenting could answer this question but I was hoping maybe someone on here already knows which way ZFS handles this situation. Thank you in advance for any insight!

    Read the article

  • Win7 System folder contains infinitely looping SYSTEM(!) directory

    - by Matt
    My Windows 7 Enterprise computer has been crashing fairly frequently recently, so I decided to boot up in safe mode and run the TrendMicro client I have installed. It froze about 10 minutes into the full system scan, so in the spirit of http://whathaveyoutried.com, I started scanning each folder individually. When I got to ProgramData, the AV failed with an uncaught exception. I then went down a level and tried scanning Application Data, which failed as well. Imagine my surprise when I open the folder just to see the same folder again! As far as I can tell, this folder loop continues indefinitely. (If you are trying to recreate this, keep in mind that ProgramData is a hidden folder.) I'm actually a bit concerned that these are system folders, as this is a brand-new computer with a clean installation. I guess I have three questions: Has anyone else seen/experienced this before? I'm running Win7 SP1. How do I fix this? I've run CHKDSK \F with no success (although it was incredibly slow). What are the ramifications of an infinitely recursive directory? Theoretically speaking, each link takes up memory, so shouldn't I have no space available on my hard drive? (I've got about 180GB left.) I noticed that the tree view on the left only shows the "linked folder" icon on the deeper folders--does this mean anything special? (I've circled the icons or lack thereof in red.) How can the OS even resolve this aberration? And above all, what would happen if I were to select "Expand all folders"??? :P Matt

    Read the article

  • How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

    - by Senseful
    I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

    Read the article

  • /usr/bin/install hangs, apparently due to SELinux

    - by Cooper
    I'm trying to use the GNU coreutils install utility, however it is hanging: /usr/bin/install -v test_file test_dir/ `test_file' -> `test_dir/test_file I see the same behavior whether I run as a normal user, or root/sudo. I ran an strace -f, and this is the end of the output: ... read(4, "<username>\t-d\tsystem_u:object_r:ho"..., 4096) = 2197 <0.000012> brk(0x6e3b1000) = 0x6e3b1000 <0.000009> mmap(NULL, 29138944, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2abd831ae000 <0.000014> munmap(0x2abd815dd000, 29138944) = 0 <0.003466> The read() is reading from /etc/selinux/targeted/contexts/files/file_contexts.homedirs, apparently successfully. It appears that the process is hanging right after the munmap, but continues to eat 100% CPU. My two questions are: 1) Any good way to see what is going on with the process? I'm currently too lazy to compile a debug version of install I can run gdb on - but a strong suggestion in an answer here may motivate me to do so if needed. 2) Any idea what the SELinux issue could be? I'm not too familiar with SELinux. Additional info of possible relevance: # ls -Z drwxr-xr-x my_user 7001 user_u:object_r:user_home_t test_dir -rw-r--r-- my_user 7001 user_u:object_r:user_home_t test_file # id ... context=user_u:system_r:unconfined_t # uname -a Linux hostname 2.6.18-238.1.1.el5 #1 SMP Tue Jan 4 13:32:19 EST 2011 x86_64 x86_64 x86_64 GNU/Linux I am suspicious that SELinux + Quest Authentication Services (QAS) is causing the issue. QAS is generally well behaved, but it did cause the /etc/selinux/targeted/contexts/files/file_contexts.homedirs to get quite large (~18k users, @23 lines per user) Update: install -v -Z user_u:object_r:user_home_t file dir/ seems to work. Can anyone suggest why, given that SELinux is in permissive mode (see comments).

    Read the article

  • How do I log back into a Windows Server 2003 guest OS after Hyper-V integration services installs and breaks my domain logins?

    - by Warren P
    After installing Hyper-V integration services, I appear to have a problem with logging in to my Windows Server 2003 virtual machine. Incorrect passwords and logins give the usual error message, but a correct login/password gives me this message: Windows cannot connect to the domain, either because the domain controller is down or otherwise unavailable, or because your computer account was not found. Please try again later. If this message continues to appear, contact your system administrator for assistance. Nothing pleases me more than Microsoft telling me (the ersatz system administrator) to contact my system administrator for help, when I suspect that I'm hooped. The virtual machine has a valid network connection, and has decided to invalidate all my previous logins on this account, so I can't log in and remotely fix anything, and I can't remotely connect to it from outside either. This appears to be a catch 22. Unfortunately I don't know any non-domain local logins for this virtual machine, so I suspect I am basically hooped, or that I need ophcrack. is there any alternative to ophcrack? Second and related question; I used Disk2VHD to do the conversion, and I could log in fine several times, until after the Hyper-V integration services were installed, then suddenly this happens and I can't log in now - was there something I did wrong? I can't get networking working inside the VM BEFORE I install integration services, and at the very moment that integration services is being installed, I'm getting locked out like this. I probably should always know the local login of any machine I'm upgrading so I don't get stuck like this in the future.... great. Now I am reminded again of this.

    Read the article

  • Unable to connect to Windows VPN from iPad

    - by Justin
    I have a 16 GB iPad wifi I can't get to connect to VPN. The error I get is: "A connection could not be established to the PP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator." I have tried a variety of tasks to troubleshoot the issue: I have verified that another iPad on another network can connect to the VPN I am trying to connect to I can connect to this VPN from the same network the iPad uses on a Windows machine I have verified an iPhone user can connect to this VPN from a different network I have reset the iPad's network settings I have reset the entire iPad and restored settings I have compared my settings w/ a screenshot from the iPad that works and confirmed everything is correct I have used the IP address and domain name of our VPN server in the settings I have tried deleting the VPN settings in the iPad and recreating them I have verified in the logs of VPN server that I'm not even getting to the VPN server (no log entry) I have verified that I cannot VPN from the iPad on separate network (different ISP and router) Are there any other ways to troubleshoot VPN on an iPad?

    Read the article

  • PHP files are downloaded, not executed in UserDir on Apache

    - by Fabian
    We're running a webserver using Debian 6.0.3 with Apache 2, we recently upgraded from Debian 5 to 6. Since then php scripts in the user directories (using mod_userdir) have stopped working, they are downloaded instead of being executed. There is also a website using php outside of the user directories, and that one continues to work fine, so PHP seems to generally work on the server. I tested it with several PHP files, among the a simple phpinfo file that works fine on the main site, but is just downloaded when copying it to one of the user directories. The php files and the directory containing them are executable for everyone. The option in the Apache php5.conf that by default disables PHP in the user directories, is commented out, so the php5.ini looks like this: <IfModule mod_php5.c> <FilesMatch "\.ph(p3?|tml)$"> SetHandler application/x-httpd-php </FilesMatch> <FilesMatch "\.phps$"> SetHandler application/x-httpd-php-source </FilesMatch> # To re-enable php in user directories comment the following lines # (from <IfModule ...> to </IfModule>.) Do NOT set it to On as it # prevents .htaccess files from disabling it. #<IfModule mod_userdir.c> # <Directory /home/*/public_html> # php_admin_value engine Off # </Directory> #</IfModule> </IfModule> We restarted Apache after changing this. I'm running out of ideas now what the problem could be, and I don't know how I could really determine which problem is preventing those php files from being executed. Any ideas on how I can solve this? Update: Strangely, PHP seems to work fine in subfolders of user directories, so if I copy a PHP file from /home/user/public_html/ to /home/user/public_html/test/ it suddenly works.

    Read the article

  • Video card not detected in POST on initial boot.

    - by Jeff M
    I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

    Read the article

  • Outlook / Gmail 'too many simultaneous connections' error

    - by sam
    I'm just setting up Outlook for Mac, and I'm trying to add a Google Apps application for business email (Gmail). I've set it up correctly (same details worked in Mac mail). But I keep getting two errors, either or just a error asking for the username and password again. Just to confirm the user name and password are correct, although when I go into menu command Tools - Account and look in the password field for that account it's blank. But if I just click cancel on the popup asking for my username password it just continues to get mail in the background for about 30 seconds, before again asking again for the password, or showing the above error which I can click 'yes' to and again it will get the mail. But after 30 seconds it does the same thing. I've got two other accounts set up fine, one a horde account (hosted webmail using POP3) and the other a iCloud .me account running on IMAP. What might be causing this and how I can remedy it? A bit more background: the machine is a MacBook Pro running Mac OS X v10.7 (Lion). Update 2013-11-02 I've updated Outlook to SP3, but I still get the same error.

    Read the article

  • kde dropping keyboard

    - by shabbychef
    I am having problems with KDE 'dropping' my keyboard. It happens periodically when using my gentoo box directly, but has become much worse when accessing via NX (from a Mac laptop). Some possibly irrelevant clues: it appears to happen more often when the system is under higher CPU load the mouse continues to work, but no windows will accept any kind of keyboard focus. kwin will not accept tabbing between windows. when working on the machine directly, I can ctrl-alt-F1 to get to a shell (obviously this does nothing over NX). so I think it is KDE and not xorg. am running kwin-4.3.5-r1, and KDE-4.3.5 generally. this problem definitely appeared after upgrading to kde-4.x, but I do not remember if it appeared in kde-4.2. sometimes the keyboard will reappear, but sometimes I have to kill my kde session. playing with accessibility options or window-focus-stealing options in system-settings under kde will often make the keyboard responsive again, only to drop it perhaps minutes later. I had read online this might be an evdev problem under X (again, I think this is KDE, not X, but will try anything). as a result, I have fiddled with my xorg.conf endlessly. I even deleted it entirely and let nvidia-xconfig have a stab at it, with no luck I am tearing my hair out over this. I have done emerge -e xorg-server and am right now doing emerge -e kwin, to rebuild all packages that might be relevant. no luck with the xorg-server rebuild. any help appreciated. thanks,

    Read the article

  • How to backup a large FreeNAS?

    - by Ze'ev
    We have a 12TB FreeNAS box in the office, and are looking for a way to keep a backup of it offsite. We're considering (1) tape; (2) a bunch of bare drives (popped into a spare hotswap bay); (3) external drives. Any advice on which solution is best? (Online backup is not an option because our internet connection is too slow.) And, is there some software that will keep track of which files have been backed up and which haven't? So that when one backup unit fills up, we can continue the backup on the next? (We don't want to have to back up to a 12TB device.) This software could run, preferably, on the NAS itself; or from one of our Mac clients. Our goal is a situation where we attach some backup device; it automatically fills up with stuff from the server; the contents of this unit are catalogued somewhere something prompts us to replace with a fresh drive/tape; backup continues until full, including any files that have changed since being backed up.

    Read the article

  • keyboard intermittently stops working, even after reinstalling windows 7; possibly a Chrome issue?

    - by neverskipbreakfast
    My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash a couple of the ctrl+alt+windows type keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu, but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) *Unplugging & reconnecting keyboard does NOT fix it. *Connecting a different keyboard does NOT fix it. That one won't work, either. *Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. *Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears, they keyboard won't work, and neither will the icon to pull up the on-screen keyboard. Otherwise my mouse can click around just fine. I can only log onto a non-password protected account. *Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. *Clearing my Chrome browsing data stopped the problem from recurring for a week or so. *I use Avira free antivirus software, and repeated scans turn up nothing fishy. *I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. The only thing I suspect is something in Google Chrome -- I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

    Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >