Search Results

Search found 1209 results on 49 pages for 'cx freeze'.

Page 40/49 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

• Intermittent CNAME forwarding

  - by Godric Seer

  I host a personal website on an old desktop that is LAMP based. Since I have a dynamic IP, I use no-ip to make sure I have a working domain name at all times. I also have a domain I have bought on GoDaddy where I have a CNAME record forwarding the www subdomain to my no-ip domain. At all times, I can connect to my website through the no-ip domain without issue. For the past several weeks, I never had an issue using the GoDaddy domain to connect (ssh or https). As of today, however, the GoDaddy domain only works for about 10 minutes at a time. I get server not found errors most of the time. Also, if I happen to be using the GoDaddy domain for an ssh connection, the connection will freeze. I have attempted to run tests using a couple of online DNS check websites, but have not gotten any errors at any time. I also contacted GoDaddy support but they had no issues connecting to the website, and therefore did not see any issues. I would like advice on how I could debug/resolve this issue. Since the problem appeared without me changing anything on my end, I hope it will resolve itself, but knowing the cause in case it happens again would be preferable. EDIT: I changed the configuration in GoDaddy to create an A (Host) that points at my current IP. This works fine, so I can access the site through the GoDaddy domain without the preceding www. I am currently waiting for a new CNAME record to propagate that points the www subdomain at the main host, rather than my no-ip domain.

  Read the article

• How to migrate a running KVM (with full disk copy) to another node?

  - by klipz

  I'm doing tests on KVM, and I'd like to see if I can make a hot migration, I mean the virtual machine won't stop running during the migration (but a few seconds of freeze is ok). I use a small cluster for my test : kvm1, kvm2, and kvmnfs. kvm1 and kvm2 runs the virtual machines kvmnfs is a NFS server, and it's mounted on /KVM on both kvm1 and kvm2 To migrate a VM (only RAM in fact) from kvm1 to kvm2, I run the same kvm command on kvm2 (with -incoming tcp:0:4444) that on kvm1, then I use "migrate -d tcp:kvm2:4444" : It works great, since the VM file is common to both machines. Now, I wan't to make a full migration (RAM + disk) of a local VM file (no more NFS) of kvm1 to kvm2. I tried to create an empty file, with touch, on kvm2 and use the same kvm command line + the "-incoming ..."). Then on kvm1 I use "migrate -d tcp:kvm2:4444" : It copies everything, then... the VM fails (any I/O disk gives an I/O error) ! And my VM file on kvm2, the one I created with touch, as still a size of 0 bytes. What am I doing wrong ? What is the exact command to use on kvm2 ? And what is the command to launch, in the monitoring mode, on kvm1 ?

  Read the article

• Suggestions for Windows 8 migration [closed]

  - by Big Endian

  I'm thinking of migrating to Windows 8. At first I hated it, but I'm pretty sure the Windows 8 model is the future, and I don't particularly want to end up hating the future like my parents, frustrated and bewildered by anything past Windows XP. I'm currently running Windows 7 and my system has been accumulating some problems. It's probably an accumulation of issues from installing too much software, changing firewall settings, installing Ubuntu alongside Windows, and... well I'm not sure, but my computer has been buggy in unexpected ways lately (freezing and unfreezing, display driver crashing and recovering, and what I call "deep freeze/thaw cycle" where the mouse won't even move for a while). I'm good at solving computer problems, but I can't seem to get to the root of these and my best idea for fixing them is making sure I've backed up every file then re-installing the entire OS. Luckily for me, a new OS is just around the corner so this would be a good time to get two things out of the way at once. The problem I see is that the upgrade options I see are all "seamless". I don't want a seamless upgrade. I want to wipe the slate clean and start all over. Does this mean I will have to buy a full, new copy of Windows 8 rather than one of the cheaper upgrading options? Or does it not make since for me to go to Windows 8 given that I have a laptop, not a tablet? Maybe I should just re-install Windows 7, or even call good enough good enough, try to eliminate the bugs, and start with a fresh slate in 2-3 years after this computer eventually dies entirely from (inevitable) hardware failure. What would be the advantages or disadvantages and costs of each option, how would I go about upgrading to Windows 8 if that's the option I choose, and what is your personal opinion about my situation?

  Read the article

• Toshiba External Hard Drive freezes computer

  - by Ephraim

  I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

  Read the article

• Debugging "clogged" TCP connections

  - by Nikratio

  I'm having trouble with an internet connection that seems to randomly "freeze" arbitrary tcp connections. The connections stay established, but no data is coming through. When this happens, netstat still shows the connection status as ESTABLISHED on both the local computer: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 53 192.168.0.10:41129 173.255.235.238:143 ESTABLISHED 8219/gnutls-cli on (79.31/13/0) ..and the remote server: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 0 173.255.235.238:143 68.5.174.98:41129 ESTABLISHED 5303/imapd off (0.00/0/0) However, it seems that no data at all is transferred. If I run strace on the local and remote process, both just show a repeating sequence of select calls (with different fds of course), e.g. select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) The internet connection overall does not seem affected, I can still establish new connections to the same service on the same server without any problems. However, the affected local applications seem to be unaware of the problem and just hang. When I look at a packet capture of this connection on the client side, the last thing that happens is that the client transmits some data, then nothing happens for about 1100 seconds, and then several TCP Retransmission requests go out, with intervals increasing from 4 seconds to 130 seconds. No activity is captured after that. After about 10 minutes, the connection on the remote end disappears from the netstat (I wasn't able to catch any intermediate state), but still stays ESTABLISHED on the local end. Finally, after some more minutes, the local application aborts with a timeout and disappears from the local netstat output as well. Does anyone have a suggestion of how I could debug this further to find out where the problem lies and how to fix it? Additionaly and/or as a temporary workaround: is is there some way to globally reduce the timeout on client and/or server to reduce the time before the local application aborts?

  Read the article

• 8007064c(2011) and 80280007(2009) persistant after all known repairs

  - by tiu44

  I'm on Windows 7 Home x64, and have ran into a major issue with Live Messenger(which I use daily). I have full offline installers for both 2011 and the last Wave 3 2009(14.0.8117.0416) Suites. Both give the following errors: Live Essentials 2011 Offline installer(official): An unknown error occured. Error:0x8007064c Source WLXSuite WL 2009 offline installer(official): You already have a more recent version of Windows Live. Error: OnCatalogResult:0x80280007 Next steps: If you want to install this older version, first uninstall any later versions that are on your computer. Get help with this error The 2011 installer also says it is updating messenger, I don't select anything else. Then last 2009 installer says their is a newer version that needs uninstalled even after the following procedures. MS Help pages provided all basically lead to using uninstall from control panel. Which I've uninstalled all Live components including watcom safety scanner and portable SQL from. I've followed online instructions for manually deleting folders from Program Files(x86), Appdata, and some others under \User\All Users and the one for the one account on the machine. I've used CCcleaner 3.01, ASC 3.7.3 and Beta 4 with deep scan along with deleting folders, and checked their uninstallers for Live components too, and none were there. wlmuninstaller.exe tool reports nothing, but after a failed install it finds something, but failes to clean it under all user admin privilege. The same errors still occur after all of that. Google searching I see people on forums suggesting reinstalling the OS cause MS doesn't even know how to fix this, but I'm hoping someone here can help. NOTE: I don't have System Restore or any other state freeze utilities going, and I don't have any real time AV going(I sometime scan with defender, anti rootkits, and online scanners). NOTE2:I posted this on windowslivehelp.com, before looking to see if the place was active or not, hoping I can get help here. Thanks

  Read the article

• SSH traffic over openvpn connection freezes when I cat a file

  - by user42055

  I have an openvpn (version 2.1_rc15 at both ends) connection setup between two gentoo boxes using shared keys. it works fine for the most part. I use mysql, http, ftp, scp over the vpn with no problems. But when I ssh from the client to the server over the vpn, weird things happen. I can login, i can execute some commands. But if i try to run an ncurses application like top, or i try to cat a file, the connection will stall and I'll have to sever the ssh session. I can, for example, execute "echo blah; echo .; echo blah" and it will output the three lines of text over the ssh session fine. But if i execute "cat /etc/motd" the session will freeze the moment I press enter. I compiled openvpn 2.1.1 on my mac and copied over my config directory from my gentoo client. The mac connected and ssh sessions worked fine without freezing. I then compiled it on my older gentoo box (2.6.26 kernel) which I am retiring due to a dying hard drive, and ssh over it also works perfectly. Why does it fail on my brand new gentoo box ? I've tried compiling three different kernels in case it was that, but other than that there should be no difference between my older and my newer gentoo boxes that I can think of. Any suggestions on what's wrong ?

  Read the article

• unable to destroy windows 2008 r2 failover cluster after SAN rebuild

  - by Zack

  I created a windows 2008 r2 failover cluster for a sql 2008 active/passive cluster. This two node cluster was using a SAN device for a quorum disk resource as well as MSDTC resource. Well....I decided to reconfigure the SAN device, but I didn't destroy the cluster first. Now that the quorum disk and mstdc disk are completely gone, the cluster is obviously not working. But, I can't even destroy the cluster and start again. I've tried from the Windows Clustering tool, as well as the command line. I was able to get the cluster service to start using the "/fixquorum" parameter. After doing this I was able to remove the passive node from the cluster, but it wouldn't let me destroy the cluster because the default resource group and msdtc are still attached as resources. I tried to delete these resources from both the GUI tool, as well as command line. It will either freeze for several minutes and crash the program, or once it even BSOD'd the server. Can someone advise on how to destroy this cluster so I can start over?

  Read the article

• Video desktop recording and multiple WM displays, capturing nonactive display

  - by okobaka

  Two WM running on one local machine. WM - Fluxbox. Using ffmpeg to record desktop. ffmpeg -an -f x11grab -s 1920x1080 -r 25 -i :1.0 -sameq /tmp/video.mkv On one display everything works great, but not when i have another WM display startx -- :1. What i am doing right now is to switch ctrl+alt+f8 to display:1.0, and start recording with ffmpeg. Everything is fine until i switch back ctrl+alt+f7 to display:0.0, WM and captured video image freezes, but when i switch back ctrl+alt+f8 to display:1.0, it unfreeze and continue recording. So, how to make display:1.0 not to freeze, while on display:0.0? Tested some more. open [display 0.0] open [display 0.1] from [display 0.0] = open => [display 0.2] same problem For different users and same users results are the same. ffmpeg keeps recording that paused image. Looks like WM root window need to be active, to be recorded.

  Read the article

• Ubuntu purple splash screen with blinking pixels?

  - by joxnas

  I had ubuntu 9.10 I upgraded to 10.04 after solving some problems (freeze at boot). Since then, I don't have the ubuntu's logo showing up when I boot, but a purple screen with some blinking pixels. I didn't care much about it... but today my computer took too long at that screen (normally it was just 1/4 second, but today it was like a minute..). And it happened like 4 or 5 times in a row (Only at the 5th time I realised that it was not freezing up, but it simply would took more time) After a reboot, it is again 1/4 second of purple screen but I don't want this problem to return.. so I want to get rid of the purple screen (I think it is an indicator of the problem) Well, I already installed the graphic drivers (going to system admnistration hardware drivers). But it didn't solve anything. (I don't know if it is even related) I searched in google, found something old (2006) and I think it maybe has some relation with my problems .. http://ubuntuforums.org/archive/index.php/t-294692.html But couldn't understand the conversation (i'm a linux novice) Sorry for my horrible english.. I would appreciate any help! My hardware: ATI Mobility Radeon 4650 HD P7450 2.13Ghz Core 2 Duo

  Read the article

• Is execution of sync(8) still required before shutting down linux?

  - by Amos Shapira

  I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

  Read the article

• Application (was Firefox) crash on first load on Ubuntu Linux on older Dell Laptop

  - by Ira Baxter

  I've had a Dell Latitude laptop since about 2000 without managing to destroy it. A month ago the Windows 2000 system on it did something stupid to its file system and Windows was completely lost. No point in reinstalling Windows 2000, so I installed an Ubuntu Linux on the laptop. Everything seems normal (installed, rebooted, I can log in, run GnuChess, poke about). ... but ... when I attempt to launch Firefox from the top bar menu icon, I get a bunch of disk activity, the whirling cursor icon goes round a bit and then (WAS: everything stops: icon, mouse. Literally nothing happens for 5 minutes. Ubuntu is dead, as far as I can tell. EDIT : on further investigation, spinning icon, mouse operated by touchpad freeze. There's apparantly a little disk activity occuring about every 5 seconds. I wait 5-10 minutes, behavior doesn't change) A reboot, and I can repeat this reliably. So on the face of it, everything works but Firefox. That seems really strange. The only odd thing about this system when Firefox is booting is that while it has an Ethernet port (that worked fine under Windows), it isn't actually plugged into an Ethernet. As this is the first Firefox boot since the Ubuntu install, maybe Firefox mishandles Internet access? Why would that crash Ubuntu? (I need to go try the obvious experiment of plugging it in). EDIT: I tried to run the Disk manager tool, not that I cared what it was, just a menu-available application. It started up like Firefox, I get a little tag in the lower left saying Disk P*** something had started, and then the same behavior as Firefox. At this point, I don't think its the Ethernet. Is it possible that the Ubuntu disk driver can't handle the disk controller in this older laptop? The install seemed to go fine.

  Read the article

• Data Store/Volume disconnecting. How to resume copy of VMDK?

  - by Serge

  I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

  Read the article

• Linux - preventing an application from failing due to lack of disk space [migrated]

  - by Jernej

  Due to an unpredicted scenario I am currently in need of finding a solution to the fact that an application (which I do not wish to kill) is slowly hogging the entire disk space. To give more context I have an application in Python that uses multiprocessing.Pool to start 5 threads. Each thread writes some data to its own file. The program is running on Linux and I do not have root access to the machine. The program is CPU intensive and has been running for months. It still has a few days to write all the data. 40% of the data in the files is redundant and can be removed after a quick test. The system on which the program is running only has 30GB of remaining disk space and at the current rate of work it will surely be hogged before the program finishes. Given the above points I see the following solutions with respective problems Given that the process number i is writing to file_i, is it safe to move file_i to an external location? Will the OS simply create a new instance of file_i and write to it? I assume moving the file would remove it and the process would end up writing to a "dead" file? Is there a "command line" way to stop 4 of the 5 spawned workers and wait until one of them finishes and then resume their work? (I am sure one single worker thread would avoid hogging the disk) Suppose I use CTRL+Z to freeze the main process. Will this stop all the other processes spawned by multiprocessing.Pool? If yes, can I then safely edit the files as to remove the redundant lines? Given the three options that I see, would any of them work in this context? If not, is there a better way to handle this problem? I would really like to avoid the scenario in which the program crashes just few days before its finish.

  Read the article

• Burners freezing the PC when starting lead write in

  - by steve

  hi guys ,am having trouble with new pioneer dvdr-219l dual layer burners ,have replaced old burners with these dual layer ones . they are sata attached ,have tried img burn, xbox360 cookie burner, dvd decrypter, dvd flick , the burners seem ok burning cd and normal dvds but when trying to burn an iso to dual layer they will both freeze at the lead in write , the pc freezes including alt/delete mouse etc so have to re-boot,have tried uninstalling all burning programs that i have to eliminate conflicts and re-installing 1 at a time to see if that was the problem , still no solution am starting to think that maybe i have a bad sata cable the pc and burners dont seem to talk to each other when trying to burn dual layer ,any suggestions ???? this problem is giving me the shits ,ran microsofts fix it program and it said i had no burners installed that were capable of burning , i have had a look at device manager and the burners are there and when trouble shooted it says they are working ok , have noticed in device manager that the driver for these burners is from B.H.A.corporation file version 8.0.0.5. copyright 2000-2006 and they are not digitally sighned these burners are the latest models so how com the drivers are so old ...help please . steve

  Read the article

• Windows Explorer Hangs on Right-Click

  - by Bryan

  I am not sure if this is the right site to post this one as I typically post coding questions on stackoverflow. But I'll ask anyways and hopefully someone can move it if it's incorrect. Currently I have a customer built PC, utilizing an Intel i7 chip, 1300WATT PSU, 8Gigs of RAM, and two video cards. Originally I had the one video card (NVIDIA) that used the PSU and had two DVI output. After purchasing a third monitor I installed another ATI) graphics card not needed any PSU connectors. After installing and restarting, I noticed that when I right-click on my desktop, or through Windows Explorer it will hang, freeze then restarted. Sometimes after Windows Explorer restarts the problem dissipates. I checked to make sure everything was connected properly and it was. I repaired the ATI Catalyst Control Center to see if that had an issue, and I checked to see if either video card required updated drivers. Nothing worked. I tried restarting my PC and that didn't work. I tried using ShellXView (I forgot what it's actually called) and tried closed processes but that didn't work. Does anyone have any idea what could have caused this orpossible solutions I should try?< Thanks in advance.

  Read the article

• SQuirreL Client: Opening up a table in a separate tab

  - by Dalin Seivewright

  I've switched to SQuirrel Client to view an Oracle database with a variety of tables. At any given time, I need to look at the contents of several related tables at the same time. The problem is that, at least by default, SQuirrel Client does not open up multiple tables at a time. When you click on a different Table object, the main view is refreshed with newly selected table data. Oracle's SQLDeveloper (which I am trying to move away from) did this by default if I recall, but there was an option to "freeze" panes. Does a similar option exist in SQuirrel Client? I do not require the ability to view the contents of two different tables on the same screen (i.e. a split view) but I would like the ability to have tabs for each table so I can quickly switch between each table view rather then having to find the table in the table list over and over again. Note: I am using this in a professional capacity but if it does not "belong" here then I suppose it could be moved to superuser.

  Read the article

• What's the best way to clone multiple PCs from one machine?

  - by Jason T.

  Where I work we have dozens and dozens of old ThinkPad laptops. A lot of these can be reused but not for our needs. They have been long since replaced. The higher-ups have decided to donate them to charity. For better or for worse I have been tasked with reimaging them. I took a laptop and installed the factory copy of Windows, updated it, configured it appropriately. Now I'm trying to reimage it to dozens of other laptops. What's some good software to do this? First I used clonezilla to clone the hdd in the laptop to an internal drive in an external enclosure and it worked. Then I tried taking the base image out and connecting it externally to a laptop that needed to be imaged and I got it to work a few times. So far so good, right? Well once I informed my boss of my findings and what I would want to do then the images started to not work on new laptops. One of three things would happen: The Thinkpads would just blink at me and Windows wouldn't load. Or Windows would load but freeze within two minutes. Last but not least the laptops would BSOD during the Windows XP bootup. These laptops are not going to be used by the company. They're going to charity. So can anyone else recommend a way to reimage multiple laptops?

  Read the article

• Master File Table Corrupt, any way to save data?

  - by domen

  hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• Weird problem with Visual C++ 2010 Express

  - by Robert Vella

  This has happened before on my Vista Premium installation, and now it's happening on my Windows 7 Home Premium installation. Basically everytime I install Visual Studio Express 2010, it works fine for a random amount of time but then suddenly starts to hide from my sight -- that's the best way I can explain it. VS does not crash, and from what I can tell it does not freeze either; It continues to work, I can even "minimize" and "maximize" it; I simply cannot see it nor can I interact with it any meaningful way. Also: After the "crash" there are no logs in: Root\Program Files (x86)\Microsoft Visual Studio 10.0\Microsoft Visual C++ 2010 Express - ENU. Nor any other files created at the time of the crash. There are no traces in the event viewer. The program seems to be functioning perfectly in the process manager. If I reinstall Visual C++, it works normally for a seemingly random period of time before going cookoo again. I am stumped. This has never happened to me before, with any other program. And yet I doubt it really is a problem with Visual C++; More like something general that seems to have picked on it for some reason. Still, after a clean install with a new OS, I'm kinda thinking there's something wrong here. Any help would be appreciated, altough I suspect that the answer to this question will make me feel embarassed. P.S. Not sure if it helps, but I think around the same time I started having problems (On both installations) with windows turning off the display when I leave the computer, and then seemingly crashing when it turns it on again -- in fact when I interact with it it seems to be responding to my commands without actually display anything.

  Read the article

• Installing Ubuntu guest crashes Hyper-V host

  - by Grant

  I have a weird problem that I don't even know where to begin diagnosing. Trying to install Ubuntu to a VM locks up the host system! My setup is: Dell R715 server, dual 16 core AMD opteron processors, 96GB RAM Dell MD3600f SAN Server 2008 R2 Datacenter System Center VMM 2012 There are 5 windows virtual machines running that have had no problems. This is the first linux VM I've tried to create. I setup a VM through virtual machine manager, set the CD drive to a Ubuntu 12.04 server x64 iso, and started it up. It boots up the normal ubuntu install menu, but the second I hit enter on "Install Ubuntu Server", I get disconnected. The HOST machine stops responding to pings. So do all virtual machines on it. It locks up entirely - keyboard on the host won't work, mouse won't move, numlock light won't change. There's no blue screen - the host is sitting at the login screen completely unresponsive. I can't find any relevant logs in event viewer after rebooting. What could cause the host machine to freeze like that? It's not a one time occurrence - it happens every time at the exact same point. Thank god this server isn't in production yet!

  Read the article

• Broken Vista. Can't open Windows settings.

  - by serena

  My neighbor has a Lenovo laptop with Windows Vista Home Basic. She's a noob and just uses the laptop for internet purposes. She said she had to close down Windows improperly (sometime ago, maybe 6 months) because of system freeze. She realized there's something wrong with her Windows when she tried to open Windows update settings. I took a look at the system and determined the following errors: When I click on Windows Updates, a bare white window opens for a sec. and closes immediately. When I try to open Computer Properties, the same thing happens. (Windows+Break doesn't work either.) When I try to open Bluetooth settings, the same thing happens. So Vista won't let me open any Windows settings, but installed programs work correctly (games, applications etc.). She has no Windows Vista discs since the laptop came with preinstalled genuine Vista. She also has no recovery discs. I don't think there is a system restore point for the time the system was stable. Now what can we do to solve this big problem?

  Read the article

• How can I totally flatten a PDF in Mac OS on the command line?

  - by Matthew Leingang

  I use Mac OS X Snow Leopard. I have a PDF with form fields, annotations, and stamps on it. I would like to freeze (or "flatten") that PDF so that the form fields can't be changed and the annotations/stamps are no longer editable. Since I actually have many of these PDFs, I want to do this automatically on the command line. Some things I've tried/considered, with their degree of success: Open in Preview and Print to File. This creates a totally flat PDF without changing the file size. The only way to automate seems to be to write a kludgy UI-based AppleScript, though, which I've been trying to avoid. Open in Acrobat Pro and use a JavaScript function to flatten. Again, not sure how to automate this on the command line. Use pdftk with the flatten option. But this only flattens form fields, not stamps and other annotations. Use cupsfilter which can create PDF from many file formats. Like pdftk this flattened only the form fields. Use cups-pdf to hook into the Mac's printserver and save a PDF file instead of print. I used the macports version. The resulting file is flat but huge. I tried this on an 8MB file; the flattened PDF was 358MB! Perhaps this can be combined with a ghostscript call as in Ubuntu Tip:Howto reduce PDF file size from command line. Any other suggestions would be appreciated.

  Read the article

• All computers on network get stuck waiting for some sites indefinetely

  - by zacaj

  This happens across three computers, running windows 7 and Ubuntu, firefox, opera, and chrome (all latest versions). I am connected to the internet through a Verizon wireless usb modem. When I try to open some web pages they will never finish loading (and usually never even show anything). The status bar at the bottom of the browser will display "Waiting for X" The servers it gets stuck on include: platform.twitter.com s7.addthis.com connect.facebook.net ajax.googleapis.com 2mdn.net Ive been getting away with just blocking them in AdBlock up until now, however the last two have been causing problems. There are some sites which require googleapis.com to load correctly, and some that wont ever load unless its blocked. eBay requires access to 2mdn.net to load pictures. On top of this its getting really annoying having to update AdBlock across all these computers whenever a new site pops up. I'm hoping there's some easier way to fix this? The different sites causing the freeze indicate to me that it's either a problem on my end (somehow?) or some server side software that got updated with a new bug?

  Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >