Search Results

Search found 2840 results on 114 pages for 'ports'.

Page 40/114 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

  • How to make proxy on nginx?

    - by Adrian K.
    How would I set my webservers to work in way described below? Http request: mypublic.com --- handled normally by nginx as it is set up already (listen 80;) Http request: myprivate.com --- handled by apache set up to work on 8080 (listen 8080) I'd like to avoid including ports when typing address in browser, some kind of mockup (proxy?). Both of domains are pointing to my machine and set up by named.

    Read the article

  • How to tunnel all traffic through Tor?

    - by HappyDeveloper
    All I want is be able to use flash and javascript while using Tor (I don't intend to use it for torrents) Normally, using flash with Tor is not recommended because firefox plugins run outside of the sandbox, so the browser's proxy settings don't apply to them, and can reveal your real IP. But I think it should be possible to also redirect flash to the same socket as the browser, and block the other outgoing ports just in case. Any ideas on how to do this?

    Read the article

  • To make use of 5.1 sound do i need a 5.1 headphone/speaker?

    - by Fellknight
    I recently bought a Toshiba X500 laptop with decent speakers & sound card in it. I want to use headphones but im unsure if they also need to have the same audio channels as the sound card (5.1 in this case). Also The laptop itself only has the two standard sound ports - headphones and microphone, does 5.1 headphones require a special kind of connection?.

    Read the article

  • few question about linux [closed]

    - by oneat
    Can I execute assembly files with all privileges (using ports)? Does the newest DSL (damn small Linux) works with winXP. (makes bootloader for it) And does it support downloading applications automatically ?

    Read the article

  • Capturing multicast data with Wireshark with IGMP Snooping Enabled at the switch

    - by Chuu
    I am trying to capture multicast traffic via Wireshark (actually TShark), however the switch has IGMP snooping enabled and will only send Multicast traffic on the ports that have an active IGMP subscription. I am currently getting around this by having a separate application hold the groups open I wish to record, but I am trying to set up a system to start/stop recording data dynamically and this extra complexity is painful. Is there a way to force Wireshark to send out IGMP Subscriptions for multicast groups it is recording?

    Read the article

  • Windows Live Mail and Palm Pre

    - by itprofessionalsgroup
    Has anyone had any luck getting Windows Live mail to sync with a Palm Pre with WebOS 1.1? I have tried the manual setup options setting up the pop3 incoming server on port 995 with SSL encryption and the smtp out going server on both ports 25 and 587 with TTL encryption. It acts like it is connected, but it just keeps wanting to refresh and never shows anything in the inbox.

    Read the article

  • Has anyone got Hamachi 2 working on EC2 Windows instances?

    - by Khash
    I have it running and can see the EC2 instance with a direct tunnel. However, I can't ping the EC2 instance nor can I browse the shared folders. I am sure of the following: - File sharing service is running - Folders are shared I have tried the following: - Turning Windows firewall off - Allowing all TCP and UDP ports and ICMP through Amazon EC2 group policy firewall The instance is a Windows 2008 DataCentre 32-bit.

    Read the article

  • USB mouse disconnecting and reconnecting randomly and often

    - by Marc
    Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

    Read the article

  • Issues connection to Ubuntu via PuTTy

    - by user1787262
    I'm not sure this is the appropriate stack exchange site to post this question on. If not, please flag this for migration. I am trying to use PuTTy ssh into my ubuntu machine which is wirelessly connected to the same network. I originally ran ifconfig to get my ubuntu machines private network IP address. I then verified that ssh was running, I even ssh'd into my school network and then into the ubuntu machine itself. No problems yet. On my windows 8 machine I ran ipconfig to get my private network IPv4 address. I then pinged my ubunty machines IP and 100% of packets were received. I figured, "OK we are ready to use PuTTy to connect to my Ubuntu Machine". Keep in mind this was my first time using PuTTy. I tried entering the IP of my ubuntu machine in the PuTTy Config GUI but I got a connection timeout. At this moment I don't really know what's going on, SSH is running on port 22 of my Ubuntu machine and I can ping the machine why is it not connecting? (I tried [username]@ip too). So I went on my Ubuntu machine and ran nmap -sP 192.168.0.1/24 and found that my windows machines IP did not show up, the host is down. I'm at a lost in something I am not very familiar with. Would anyone be able to help me or direct me to some resources that would trouble shoot my problem? Thank you EDIT (ADDITION): tyler@tyler-Aspire-5250:~$ nmap -v 192.168.0.123 Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 01:56 MDT Initiating Ping Scan at 01:56 Scanning 192.168.0.123 [2 ports] Completed Ping Scan at 01:56, 3.00s elapsed (1 total hosts) Nmap scan report for 192.168.0.123 [host down] Read data files from: /usr/bin/../share/nmap Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 3.14 seconds tyler@tyler-Aspire-5250:~$ nmap -Pn 192.168.0.123 Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 01:56 MDT Nmap scan report for 192.168.0.123 Host is up (0.022s latency). Not shown: 998 filtered ports PORT STATE SERVICE 2869/tcp open icslap 5357/tcp open wsdapi Nmap done: 1 IP address (1 host up) scanned in 72.51 seconds

    Read the article

  • Amazon blocked port 80 and 443 on my instance

    - by Burak
    Amazon AWS sent me an email about warning that my instance have been behaving like Phising that is against AWS Customer Agreement. And they noticed that they blocked port 80 and 443 which are for HTTP and HTTPS respectively. Google Safe Browsing also reported that some code injection was made to one of my websites. After a cleaning, Google stopped blocking my website displaying in the search result. So, how can I unblock my ports?

    Read the article

  • Correct location of git on Mac OS X

    - by zcreem
    On Mac OS x 10.6.6 I have git installed in /usr/bin/ I wanted to update the got version however the the git installer puts it in /usr/local/git/bin/ I realise I could rearrange to path to point to the local one first but what I do not get is where the /usr/bin version came from. Could it be part of an xcode install and lastly how would I delete correct it. I have looked and looked but find nothing and I didn't install it with ports etc. thanks

    Read the article

  • WiFi N Gigabit Router

    - by SLaks
    I'm looking for a WiFi N Gigabit router. I'll be using an iPod Touch 2G and a 2009 17" MacBook Pro over WiFi, and I need at least 4 gigabit ethernet ports plus a WAN port. What do people recommend? In particular, are there any compatibility issues between different WiFi N drafts that would limit the speed of the MacBook, and is it worth getting dual-band?

    Read the article

  • Setting up SSL on apache on linux ubuntu

    - by ThomasReggi
    I'm trying to get SSL to run on my apache web server. I do not have the DNS for the domain setup yet is that an issue? How do I setup SSL on my web server? When I start apache it fails. root@vannevar:/etc/apache2/ssl# service apache2 start * Starting web server apache2 Action 'start' failed. The Apache error log may have more information. The log stats that it's unable to read the certificate. [Thu Jun 28 15:01:02 2012] [error] Init: Unable to read server certificate from file /etc/apache2/ssl/www.example.com.csr [Thu Jun 28 15:01:02 2012] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Thu Jun 28 15:01:02 2012] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error The contents of /etc/apache2/httpd.conf ServerName [SERVERIP] The contents of /etc/apache2/ports.conf # If you just change the port or add more ports here, you will likely also # have to change the VirtualHost statement in # /etc/apache2/sites-enabled/000-default # This is also true if you have upgraded from before 2.2.9-3 (i.e. from # Debian etch). See /usr/share/doc/apache2.2-common/NEWS.Debian.gz and # README.Debian.gz NameVirtualHost [SERVERIP]:443 NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> The contents of /etc/apache2/sites-available/www.example.com <VirtualHost *:80> ServerAdmin [email protected] ServerName example.com ServerAlias www.example.com DocumentRoot /srv/sites/example.com/public/ ErrorLog /srv/sites/example.com/logs/error.log CustomLog /srv/sites/example.com/logs/access.log combined </VirtualHost> <VirtualHost [SERVERIP]:443> SSLEngine On SSLCertificateFile /etc/apache2/ssl/www.example.com.csr SSLCertificateKeyFile /etc/apache2/ssl/www.example.com.key SSLCACertificateFile /etc/apache2/ssl/comodo.crt ServerAdmin [email protected] ServerName example.com ServerAlias www.example.com DocumentRoot /srv/sites/example.com/public/ ErrorLog /srv/sites/example.com/logs/error.log CustomLog /srv/sites/example.com/logs/access.log combined </VirtualHost>

    Read the article

  • Finding latest successful logins and failed attempts to a CentOS server

    - by ahmad
    I'm looking for a log file or any service to report the latest login attempts which have failed due to username/password miss match. Is there such utility available for CentOS? (built-in is preferred) My second question, and more generally, I need a log file of penetration attempts to my server. Ideally, this log should contain all attempts including logins, httpd activities, and other conventional open ports.

    Read the article

  • RV042 - switch needed

    - by David
    I have a Cisco RV042 4-port but unfortunately I ran out of ports and I need to connect 2 more servers to it. I'm planning to get a SOHO switch, but I would like some recommendations before getting one. I was thinking a Dell PowerConnect. Any ideas will be appreciate it.

    Read the article

  • (Free) SSH tunneling to S60?

    - by Jawa
    What solutions are there to SSH tunneling certain ports on a Symbian S60 mobile phone? My goal is to rsync files to/from the phone but the only S60 SSH forwarding software that I know is pretty old and most importantly not free. (sshforwarding.com)

    Read the article

  • Is it possibile to alow port forwarding only for specific IP public addresses

    - by adopilot
    I have freeBSD router and it host public IP address, I am using ipnat.rules to configure port forwarding prom public network inside my private network. Now I wondering can I restrict only specific public IP addresses to can pass trough my port forwarding. What I want is to only my specific public IP addresses can walk inside my network on specific ports. Here is how now look like my ipnat.rules file rdr fxp0 217.199.XXX.XXX/32 port 7900-> 192.168.1.12 port 80 tcp

    Read the article

  • LVS Configuration issue (Using piranha Tool)

    - by PravinG
    I have configured LVS on cent os using piranha tool .I am using vip of internal n/w as gateway for real server we have two NIC one having exteranl Ip and other for internal n/w which is on 192.168.3.0/24 network. But I am not able to connect from client it shows connection refused error . Please suggest iptables rules for private n public n/w to communicate. May be I am missing this . Iptables rules that we have added are : iptables -t nat -A POSTROUTING -p tcp -s 192.168.3.0/24 --sport 5000 -j MASQUERADE this is my ipconfig: eth0 Link encap:Ethernet HWaddr 00:00:E8:F6:74:DA inet addr:122.166.233.133 Bcast:122.166.233.255 Mask:255.255.255.0 inet6 addr: fe80::200:e8ff:fef6:74da/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94433 errors:0 dropped:0 overruns:0 frame:0 TX packets:130966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9469972 (9.0 MiB) TX bytes:19929308 (19.0 MiB) Interrupt:16 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:00:E8:F6:74:DA inet addr:122.166.233.136 Bcast:122.166.233.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:E0:20:14:F9:2D inet addr:192.168.3.1 Bcast:192.168.3.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:20ff:fe14:f92d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:123718 errors:0 dropped:0 overruns:0 frame:0 TX packets:148856 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18738556 (17.8 MiB) TX bytes:11697153 (11.1 MiB) Interrupt:17 Memory:60000400-600004ff eth1:1 Link encap:Ethernet HWaddr 00:E0:20:14:F9:2D inet addr:192.168.3.10 Bcast:192.168.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:17 Memory:60000400-600004ff eth2 Link encap:Ethernet HWaddr 00:16:76:6E:D1:D2 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:21 Base address:0xa500 and ipvsadm -ln command [root@abts-kk-static-133 ~]# ipvsadm -ln IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 122.166.233.136:5000 wlc TCP 122.166.233.136:5004 wlc lvs server routing table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 122.166.233.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1004 0 0 eth1 0.0.0.0 122.166.233.1 0.0.0.0 UG 0 0 0 eth0 real 1 real 2 we have configured various ports from 5000:5008 . Do we need to this iptables for all ports? Suggest me how should I solve this issue.

    Read the article

  • Make Apache server available on a LAN via custom ServerName

    - by samwatt
    Hi, is it possible to set up an Apache server on a machine which is part of a LAN, then allow machines on the LAN to access the server via a custom ServerName (instead of Localhost). I want to serve a simple website in an office space using a short ServerName (no ports etc if possible), but I want to make sure this is possible (after originally being certain it was!). THanks in advance.

    Read the article

  • How can I simulate blocking RTMP over port 80 on Windows?

    - by Christian Nunciato
    It seems like this should be so simple, but since this isn't my area of expertise, I'm having a hell of a time figuring out how to do it. Basically, I have a Flash app and I'm connecting to a Flash Media Server to stream some content. The URL I'm using to do this, for example, looks like this: rtmp://someserver.com/some/path/mp3:somefile Everything works -- but that's sort of the problem. When I'm trying to do is simulate my users attempting to play back my media under more restrictive conditions than the ones I have here (i.e., none) -- namely being stuck behind firewalls or proxy servers that block access to RTMP streams. Flash, according to Adobe, is equipped to handle proxy servers and firewalls automatically, like so (from the docs): When you do not specify a port number in an RTMP address, Flash will attempt to connect to port 1935. If it fails it will then try to connect to port 443; if that fails, it will try port 80. [And if that fails, it will attempt to connect via RTMPT (i.e., HTTP tunneling) on port 80.] So no coding is required to access ports 1935, 443, or port 80 if you do not specify a port in the RTMP address. The problem I'm having is setting up a reliable environment in which to test that this behavior actually happens. I'm on a Windows machine, for example, so with Windows Firewall, I can block certain ports and protocols (1935, 443), but I don't want to block port 80, because the final fallback protocol (RTMPT) is supposed to run on port 80, and Windows Firewall only gives me enough granularity (as far as I know, anyway) to block "all outbound TCP traffic to remote port 80" -- that is, I can't, apparently, block "all outbound RTMP traffic to port 80" while leaving RTMPT traffic to port 80 unaffected. My understanding thus far is that I'll probably need to set up a proxy server to do this. Is this correct? Or is there a simpler way (on Win 7, at least) to filter out RTMP to 1935, RTMP to 443, RTMP to 80, but still allow RTMPT to 80 (where all four hostnames are identical)? And if I do have to set up a proxy server, what's the simplest way to go on Windows? I've set up WinProxy, which seems a bit janky but apparently works -- but then what I can't figure out is how to tell Windows to force all TCP traffic (including RTMP, RTMPT and HTTO) through this proxy server so I can turn around and reject the requests for RTMP. Any help would be hugely appreciated. This isn't my realm of expertise and I've alreasdy spent more time on it than I probably should. :)

    Read the article

  • How do you keep track of what's connected to your switches?

    - by Kamil Kisiel
    Currently we manually document the connections to the ports of our switches. Of course, maintenance is a chore, and the documentation is out of date as soon as you save it. Are there any tools for querying switches, preferably via SNMP, that can tell you what is connected on the other end? For the record, we use primarily HP ProCurve switches.

    Read the article

  • Our embedded linux system won't recognize a USB Device if it is plugged in before powerup. Suggestions?

    - by Blaine
    We are developing on a small embedded device. This device us a gumstix overo board running OpenEmbedded linux. We have our development almost completely done, and have run into the strangest of bugs that we can't figure out. We have a USB Device (Spectrophotometer) that has a USB2.0 Connection and an external power supply for the light source. Typical behavior is that you plug in the power supply, then the USB connection to a host. When the usb connection is detected by the device, the device boots up and enables the light source and fan. The device is then able to be used by the host system. The problem is that if the device is plugged into the Gumstix before we turn on the Gumstix, the USB Device apparently is not probed by the system (and hence does not turn on). Under a normal situation, when the connection is initialized by plugging in the usb cable, the spectro turns itself on and becomes available to the system (this can be seen via "lsusb" typically). Neither of these things are happening. There is no device detected via "lsusb" and no dmesg errors of any kind that we can see. It is as if the device is not plugged in. The device does show up and work fine if we unplug the USB cable and plug it back in once the system is booted up. It turns on and shows up on the usb bus, and we can access it with our driver. On any other desktop or laptop, it does not matter if the host system is on or off when we plug in the spectrometer. This behavior is what I would consider to be "normal" - that the usb system is probed and initialized at boot time, and the usb devices come online. In other words, our system is fully functional as long as we plug in the usb device after the system is booted up. Unfortunately this isn't possible in our final product - everything comes on at once. Additional Info: 1) We have tried a flash drive attached to the system when the system is turned off. Booting up the system brings the flash drive online, as expected 2) There are no messages regarding the spectro or usb device (using dmesg). "lsusb" only lists the USB hubs / controllers. It is literally as if the device is not present and not plugged in. 3) We have tried a brand new image from gumstix and an older image from last year. Both images have this problem. This problem exists on all 3 gumstix devices we use. Does anyone have any suggestions? From what I can tell it isn't really possible to do a complete "reboot" of the usb system that is a complete emulation of "unplugging" and "replugging" a usb device. I feel like what is happening is that there is no initial probe on the usb bus that would trigger the usb handshaking, but this is somehow specific to the spectro. This seems to be a kernel issue or at least an issue in how the kernel is initializing the usb subsystem. I'm not really sure though. I have tried the gumstix mailing list, but there doesn't seem to be anyone who has seen this issue before. Any advice or suggestions on where to start looking would be fantastic. Thank you! Blaine output etc. $ uname -a Linux overo 2.6.33 #1 Tue Apr 27 08:35:38 PDT 2010 armv7l GNU/Linux When the system is up and running and spectro is plugged in (working as intended), this is lsusb: Bus 001 Device 116: ID 2457:1022 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x2457 idProduct 0x1022 bcdDevice 0.02 iManufacturer 1 USB4000 1.01.11 iProduct 2 Ocean Optics USB4000 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 400mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) dmesg output: usb usb1: usb auto-resume hub 1-0:1.0: hub_resume usb usb2: usb auto-resume ehci-omap ehci-omap.0: resume root hub hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 hub 2-0:1.0: hub_resume hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend ehci-omap ehci-omap.0: suspend root hub usb usb2: usb resume ehci-omap ehci-omap.0: resume root hub hub 2-0:1.0: hub_resume ehci-omap ehci-omap.0: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT hub 2-0:1.0: port 2: status 0501 change 0001 hub 2-0:1.0: state 7 ports 3 chg 0004 evt 0000 hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: new high speed USB device using ehci-omap and address 2 ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: default language 0x0409 usb 2-2: udev 2, busnum 2, minor = 129 usb 2-2: New USB device found, idVendor=2457, idProduct=1022 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Ocean Optics USB4000 usb 2-2: Manufacturer: USB4000 1.01.11 usb 2-2: uevent usb 2-2: usb_probe_device usb 2-2: configuration #1 chosen from 1 choice usb 2-2: uevent usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: uevent drivers/usb/core/inode.c: creating file '002' dmesg has nothing to say, and lusb simply lists nothing else but the two default usb controllers / hubs if we plug the device in before the system is turned on.

    Read the article

  • SQlite and zabbix

    - by chris
    Has anyone ever used sqlite as the only database for their zabbix server? I'll be monitoring a uplink ports on a couple hundred switches and a small number of other services such as radius or http servers. This will be on an oldish opteron server with 2 cpus and 8gb of ram.

    Read the article

  • mac hostname problem

    - by codeshepherd
    my hostname is newton ...when I set "127.0.0.1 Newton" in /etc/hosts .. parallels stops working.. when I set "127.0.0.1 localhost" in /etc/hosts apache installed via ports stops working.. when I add both '"127.0.0.1 localhost", and "127.0.0.1 newton" to hosts file.. parallels network doesnt work

    Read the article

  • Making application behind reverse proxy aware of https

    - by akaIDIOT
    https in tomcat being the hassel it is, I've been trying to get an Axis2 webapp to work behind a reverse proxy for ages now, can't seem to get it to work. The proxying itself works like a charm, but the app fails to generate 'links' (or ports as it concerns SOAP) using https. It would seem I need some way to let Axis2 know it is being accessed through https, even though the actual transport to it is done over http (proxied from localhost). The nginx config that proxies https to localhost:8080: server { listen 443; server_name localhost; ssl on; ssl_certificate /path/to/.pem ssl_certificate_key /path/to/.key; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv3:+EXP; ssl_prefer_server_ciphers on; location / { # force some http-headers (avoid confusing tomcat) proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $http_host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; # pass requests to local tomcat server listening on default port 8080 proxy_pass http://localhost:8080; } } The proxy itself works fine, the info pages of the webapp work. The problem lies in the ports generated in the .wsdl: <wsdl:service name="WebService"> <wsdl:port name="WebServiceHttpSoap11Endpoint" binding="ns:WebServiceSoap11Binding"> <soap:address location="http://10.10.3.96/axis2/services/WebService.WebServiceHttpSoap11Endpoint/"/> </wsdl:port> <wsdl:port name="WebServiceHttpSoap12Endpoint" binding="ns:WebServiceSoap12Binding"> <soap12:address location="http://10.10.3.96/axis2/services/WebService.WebServiceHttpSoap12Endpoint/"/> </wsdl:port> <wsdl:port name="WebServiceHttpEndpoint" binding="ns:WebServiceHttpBinding"> <http:address location="http://10.10.3.96/axis2/services/WebService.WebServiceHttpEndpoint/"/> </wsdl:port> </wsdl:service> The Host header does its job; it shows 10.10.3.96 in stead of localhost, but as the snippet shows: it says http:// in front of it in stead of https://. My client app can't deal with this... Adding proxyPort and proxyName to the tomcat6 server.xml in the default <Connector> doesn't help; I'm at a loss on how to get this to work properly.

    Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >