Search Results

Search found 11313 results on 453 pages for 'ip aliasing'.

Page 401/453 | < Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >

  • Ubuntu networking issue: two specific machines cannot browse web while connected to network at the same time.

    - by jensendarren
    I have setup a secure wireless network which works very well except for two laptops running Ubuntu 10.10 that can't access the Internet via a browser at the same time. They can both ping sites, wget sites, use skype but when using a browser the page never loads (in Firefox the status bar just sits there saying "Connecting" until it times out.) Here is what we have tried so far (nothing has fixed this issue): OpenDNS Restart networking services Using wired connection rather than wireless Removing all other nodes from the network except the two machines that have this issue Swapped out the router Factory reset the router Reformatted one of the machines and re-installed Ubuntu 10.10 Other things that we have checked: The two machines can connect simultaneously without any issues to other wireless networks in different locations (say in an Internet Cafe or another office) The two machines have unique IP addresses The two machines have unique MAC addresses The two machines can communicate on the network using Skype, wget, ping etc We are not using a proxy on either machine FYI: I have attached output from wireshark. For the test we turned both machines on and pointed them both to the same website. The content loaded on one and not the other. Here is the output from wireshark- (speedyshare.com/files/26228631/machine_output_1 && speedyshare.com/files/26228649/machine2). As you can see the first one worked, the second one didn't. I don't fully understand the output and would appreciate if someone could shed some light on what might be causing this and how we can fix it! Many thanks! Darren

    Read the article

  • how to block spam email using Microsoft Outlook 2011 (Mac)?

    - by tim8691
    I'm using Microsoft Outlook 2011 for Mac and I'm getting so much spam I'm not sure how to control it. In the past, I always applied "Block Sender" and "Mark as Junk" to any spam email messages I received. This doesn't seem to be enough nowadays. Then I've started using Tools Rules to create rules based on subject, but the same spammer keeps changing subject lines, so this isn't working. I've been tracking the IP addresses they also seem to be changing with each email. Is there any key information I can use in the email to apply a rule to successfully place these spam emails in the junk folder? I'm using a "Low" level of junk email protection. The next higher level, "high", says it may eliminate valid emails, so I prefer not to use this option. There's maybe one or two spammers sending me emails, but the volume is very high now. I'm getting a variation of the following facebook email spam: Hi, Here's some activity you have missed. No matter how far away you are from friends and family, we can help you stay connected. Other people have asked to be your friend. Accept this invitation to see your previous friend requests Some variations on the subject line they've used include: Account Info Change Account Sender Mail Pending ticket notification Pending ticket status Support Center Support med center Pending Notification Reminder: Pending Notification How do people address this? Can it be done within Outlook or is it better to get a third party commercial software to plug-in or otherwise manage it? If so, why would the third party be better than Outlook's internal tools (e.g. what does it look for in the incoming email that Outlook doesn't look at)?

    Read the article

  • Bad Mumble control channel performance in KVM guest

    - by aef
    I'm running a Mumble server (Murmur) on a Debian Wheezy Beta 4 KVM guest which runs on a Debian Wheezy Beta 4 KVM hypervisor. The guest machines are attached to a bridge device on the hypervisor system through Virtio network interfaces. The Hypervisor is attached to a 100Mbit/s uplink and does IP-routing between the guest machines and the remaining Internet. In this setup we're experiencing a clearly recognizable lag between double-clicking a channel in the client and the channel joining action happening. This happens with a lot of different clients between 1.2.3 and 1.2.4 on Linux and Windows systems. Voice quality and latency seems to be completely unaffected by this. Most of the times the client's information dialog states a 16ms latency for both the voice and control channel. The deviation for the control channels mostly is a lot higher than the one of the voice channels. In some situations the control channel is displayed with a 100ms ping and about 1000 deviation. It seems the TCP performance is a problem here. We had no problems on an earlier setup which was in principle quite like the new one. We used Debian Lenny based Xen hypervisor and a soft-virtualised guest machine instead and an earlier version of the Mumble 1.2.3 series. The current murmurd --version says: 1.2.3-349-g315b5f5-2.1

    Read the article

  • VLAN Through Switch Doesn't Work

    - by vcsjones
    I have the following scenario: I have a Cisco Aironet 1040 access point. I have it configured with two SSIDs, each going to a different VLAN. So: SSID internal : VLAN 90 SSID guest : VLAN 70 On the router side, I have a Cisco RV220W (with the radios now turned off) and have setup VLANs with like VLAN IDs. VLAN 90 : 192.168.90.0/24 VLAN 70 : 192.168.70.0/24 As far as DHCP is concerned, each VLAN has a "DHCP Server" in the router's configuration: So with the access point connected directly to the router, everything works great. I connect to the internal network, and I get a 192.168.90.x address, and the guest network gets a 70.xxx address. Next I introduced a Cisco SG200-50 PoE switch between the router and the access point. The port is configured as a trunk port, so the VLAN tags should go right through the switch back to the router. However, when something is connected to the access point, nothing works. It isn't able to get an IP address, and manually assigning one doesn't seem to let any traffic route. Given that the access point works correctly when connected to the router directly, I believe the switch is misconfigured. What am I missing here? What can I use to better diagnose what the problem might be? It's small business equipment, so CLI access is not available. Below are screenshots of the switch's config. The access point is connected to GE2.

    Read the article

  • DNS Zone file and virtual host question (repost because my question got moved and now I can't comment on the original for some reason)

    - by Jake
    Sorry this is a repost, the original question got moved to here form stack overflow and for some reason I can't comment or respond to answers on that one anymore. Hi all, I'm trying to set up a virtual host for redmine.SITENAME.com. I've edited the httpd.conf file and now I'm trying to edit my DNS settings. However, I'm not sure exactly what to do. Here's an snippet of what's already in the named.conf file (the file was made by someone else who is unreachable): zone "SITENAME.com" { type master; file "SITENAME.com"; allow-transfer { ip.address.here.00; common-allow-transfer; }; }; I figure if I want to get redmine.SITENAME.com working, I need to copy that entry and just replace SITENAME.com with redmine.SITENAME.com but will that work? I was under the impression I needed a .db file but I don't see any reference to one in the current named.conf file. I also don't see any .db files or files named SITENAME in named.conf's directory. Any ideas where these illusive pre-existing db files could be?

    Read the article

  • OS X can connect to Windows machine, but can't access shared folders

    - by Bonnie
    I can create new folders on my Windows XP machine, set them to "shared". On my Mac, I pick Finder → Go → Connect to Server → smb://192.168.1.4 → Connect → Name / Password. It even shows me all the names of the newly created shared-folders on my PC, but when I try to actually connect to any of them I get connection failed, there was an error connecting Any idea on what would cause that? The fact that it successfully gets so far—to actually showing me my PC share-names—must mean I have 99% of this working correctly, i.e. the physical connection, the IP address, the user name, the password, etc. Still, I can't seem to access the folders themselves. I've tried this with my Windows XP firewall on/off, and Norton AntiVirus on/off. Same problem. Everything did work fine, 4 months ago. Were there any odd OS X or Windows updates released recently? I always apply them all. smbclient on the Mac does correctly find the XP machine, my XP user name, and accepts my XP password. I get the following from that smbclient command: Doing spnego session setup (blob length=16) server didn't supply a full spnego negprot Got challenge flags: ... Got NTLMSSP flags: ... Got NTLMSP flags: ... Domain=[XPMACHINE] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] tree connect failed: NT_STATUS_INSUFF_SERVER_RESOURCES I'm not sure why a standard XP box can't "supply a full spnego negprot". Whatever that means. Using XP's RegEdit to change my IRPStackSize from 11... to 13, 15, 20, 22... still gives that "NT_STATUS_INSUFF_SERVER_RESOURCES" error on the Mac.

    Read the article

  • Ubuntu 12.04 open port 80 inside WLAN

    - by Eduard
    I have an nginx server running on ubuntu 12.04 that serves http through port 80 and https through port 443. Everything works fine if I access it from the same computer via localhost, 127.0.0.1 or the local IP 192.168.0.11. If I try to access the server from another computer in the same VLAN it does not work for http; it works for https. I have changed my nginx configuration to also listen to port 8000 for http; I can then access http from the other computer in the same VLAN via "http://192.168.0.11:8000". I also have a web server running on port 80 on a windows machine and can access it from another device in the same VLAN, therefore the router is not blocking incoming http traffic. The nginx process is run by root. I have used tcpdump and I see that packets are arriving to Ubuntu: 192.168.0.16.49735 192.168.0.11.80 and that some response is being given 192.168.0.11.80 192.168.0.16.49735 (I do not know what the response is though). There is no request arriving at the nginx web server (I have checked the access log). I have iptables empty. I have unsuccessfully tried to find a solution for a long time to this, it has now become a matter of happiness or bitterness :).

    Read the article

  • Connecting to unsecured wireless network

    - by Sanchez
    I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

    Read the article

  • Barriers to IPv6 deployment: addressing

    - by sysadmin1138
    There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

    Read the article

  • Setting up port forwarding for web server

    - by Javier Badia
    This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

    Read the article

  • Mounting any Windows share from OS X 10.7.5 suddenly stopped working

    - by user2169619
    I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

    Read the article

  • can't get to admin page after factory reset netgear wg602

    - by stefanB
    I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

    Read the article

  • copy large LVM volume(14TB) from one server to another

    - by bruce
    recently,I have to copy a very large LVM volume()rom server A to server B. Below is the filesystem of server A and server B - server A [root@AVDVD-Filer ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_avdvdfiler-lv_root 16T 14T 1.5T 91% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/vg_avdvdfiler-test 2.3T 201M 2.1T 1% /test /dev/sr0 3.3G 3.3G 0 100% /mnt server B [root@localhost ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-LogVol00 20G 2.5G 16G 14% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/VolGroup00-LogVol00 16T 133M 15T 1% /xiangao/lv1 /dev/mapper/VolGroup00-LogVol01 4.7T 190M 4.5T 1% /xiangao/lv2 I want to copy LVM volume /dev/mapper/vg_avdvdfiler-lv_root on server A to LVM volume /dev/mapper/VolGroup00-LogVol00 on server B . The server A and server B is in the same IP segment. IN the LVM volume on server A , there is all average 500M avi wmv mp4 etc. I tried mount /dev/mapper/vg_avdvdfiler-lv_root on server A to server B through NFS , then use cp command copy. It is clear I faild . Because the LVM volume is too big , I do not have good idea . I hope a good solution here. I'm a chinese, my english is very pool. sorry thanks everyone!

    Read the article

  • Why are certain folders in my XP network share really, really slow?

    - by bikefixxer
    I have a workgroup set up with Windows XP. My file "server" is running XP Pro and the clients are running XP home. I've turned simple file sharing off on the server because certain clients need access to certain folders and not to others, and I want to keep it that way. Therefore, I've used the granular sharing/security settings to enable certain clients access to certain folders. I'm using the net use command in a batch file on the clients to add the share when they logon so it's always available via a mapped drive or a shortcut. On some clients "My Documents" points to the mapped drive, but all of the local and application settings stay local. Everything works well except for accessing a certain folder on the network. It contains a lot of random batch files and self-executable programs I use for diagnostics and what not, and nearly every time I open the folder the computer hangs for 15-60 seconds. This happens on every machine, including the server (but not nearly as often as the clients). I've searched high and low and cannot figure it out and it's driving me crazy. Here are all the things I've tried to no avail: Disabled firewall (XP) and anti-virus (ESET NOD32) Deleted any desktop.ini file I can find in the share Disabled "automatically search for network folders and printers" Disabled "remember each folder's view settings" Set HKCU\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer NoRecentDocsNetHood = 1 Tried with mapped drives and with UNC shortcuts Ran CHKDSK Removed Read-Only attribute from all folders (well, tried to remove, it always came back on with a half check) Added the server's static IP to the hosts file on the clients I've tried monitoring the server's performance to see if anything makes sense. Occasionally the issue coincides with a spike in pages/sec (memory) but not always. Other than that, everything else seems normal. The anti-virus would seem to be the most likely cause to me considering the batch files and what not, but it still hangs when it is completely disabled. I'm at a loss and if anyone can help me with this I'd greatly appreciate it!

    Read the article

  • Connect by Wifi to Sql Server from another computer

    - by Bronzato
    I try to connect by Wifi to Sql Server with Sql Server Management Studio from another computer but it failed. I have a computer with Windows Seven & Sql Server 2008 (lets say the server computer). Next to it, I have a fresh installed computer with Windows Seven & Sql Server Management Studio (let's say the client computer). What I do on the server computer: configure firewall by enabling port 1433 enabled network protocols (TCP/IP) inside Sql Server Configuration Manager checked "Allow remote connections to this server" on server properties in Sql Server Management. started Sql Server Browser restarted services (Sql Server Browser is stopped but I think it is not neccessary, isn't it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to Sql Server on my other computer. Ok, something new on this problem: until now, I successfully connected to my "server computer" with Management Studio. What I do is typing the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of sql server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name... Nevermind. Now my new challenge is to succeed connecting my VB6 application to this remote database located on my "computer server". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's wrong? Thanks

    Read the article

  • libvirt's dnsmasq does not respond to dns queries or provide dhcp

    - by Jeremy
    This is on Ubuntu 10.04 server, using KVM to run Ubuntu guests. This system has been working for a long time and I have not changed anything (other than applying security updates), but today I found dnsmasq no longer responds to requests. I cannot say how long this has been broken for me because I don't frequently use the NAT'd guests. So it could have started just after the last updates or some other event and I just now found it. I can connect to port 53 with telnet at 192.168.122.1. I've flushed ip-tables to be sure it wasn't firewall rules and that is not the problem. dnsmasq is running, virsh reports default network as stared. I can't find ANY information on troubleshooting libvirt dnsmasq except that it won't play well with other instances of dnsmasq, which is not the problem. I cannot even find where log entries might be for this service. Any ideas on where to look for more information? edit to add: I added another network and that one works fine. I guess I have a workaround but would still like to figure out how to troubleshoot this problem.

    Read the article

  • Suddenly can't send E-Mails with Apple Mail to Gmail SMTP

    - by slhck
    Hi all, I have a weird problem that started just today. I am using Apple Mail on a Leopard machine, connecting to Gmail. Fetching e-mail works just fine. My SMTP settings are also correct. Still, I can't send mail, it will display a pop up saying that "transferring the content to the mail server" failed (translation from German, could be different in English OS X versions). I have verified the following: My SMTP settings are definitely correct. I have not changed them and the issue appeared today. Also, I went through the Apple online configuration for Gmail accounts and did not have to adjust any setting. I can run network diagnosis and it will connect to both POP and SMTP servers without a problem (all green lights) The Telnet details will show me the HELO message from the Gmail servers, so there's no authentication failure. Console.app will not show any messages related to "mail" when I try to send the mail, so there's no specific error message The mail I'm trying to send does not have an attachment, it is plaintext only I can login to gmail.com and send mails without a problem The recipient address exists and contains no syntax errors I can also not send mails to myself When using another IP and ISP (through VPN), it still doesn't work As for my settings: I connect to smtp.gmail.com and for advanced settings I choose password-based authentication with user: [email protected] and my password. I let Apple Mail try the default ports (for SSL and TLS, respectively). Again: I have not changed a thing between yesterday and today. What is causing that strange behavior? Any help would be much appreciated.

    Read the article

  • Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

    - by Bill
    I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

    Read the article

  • nginx - proxy_pass is working - Apache isn't doing what it should...

    - by matthewsteiner
    So, I've got this in my nginx.conf: location ~* ^.+.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { root /var/www/vhosts/example.com/public/; access_log off; expires 30d; } location / { proxy_pass http://127.0.0.1:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } So anything that is a "static file" that exists will just be done with nginx. Otherwise, it should pass it off to Apache. Right now, static files are working correctly. However, if something is passed to apache and it's example.com or subdomain.example.com, apache just spits out the "Apache 2 Test Page" that you get if there's nothing there. Apache worked fine before, so I'm guessing it has to do with the way nginx is "asking". I'm not sure though. Any ideas?

    Read the article

  • Map a URL bought with Dreamhost to Amazon EC2 (AWS)

    - by Edan Maor
    I have several URLs I purchased through Dreamhost. I'm starting to use Amazon's AWS, and I'd like to map the URLs to Amazon. This is something of a silly question, and I've already done the same thing several times to other services (mapping from Dreamhost to WebFaction). But for some reason when I tried to find the proper way to do the same mapping to Amazon, I find a lot of detailed writing talking about whether I should be using CNAME or A records, etc. So I wanted to ask in the simplest possible terms and hopefully get a simple, concrete answer: I bought a URL from Dreamhost, I have an EC2 server running on AWS (to which I already mapped an Elastic IP address). How do I make the URL map to AWS? And if there are several options, which one should I effectively be using? P.S. Meta-question - why are things so much more difficult with AWS? When I search Google for "Move from Dreamhost to WebFaction, I get very simple answers on how to do the mapping. In what way is AWS different?

    Read the article

  • SSL Handshake negotiation on Nginx terribly slow

    - by Paras Chopra
    I am using Nginx as a proxy to 4 apache instances. My problem is that SSL negotiation takes a lot of time (600 ms). See this as an example: http://www.webpagetest.org/result/101020_8JXS/1/details/ Here is my Nginx Conf: user www-data; worker_processes 4; events { worker_connections 2048; use epoll; } http { include /etc/nginx/mime.types; default_type application/octet-stream; access_log /var/log/nginx/access.log; sendfile on; keepalive_timeout 0; tcp_nodelay on; gzip on; gzip_proxied any; server_names_hash_bucket_size 128; } upstream abc { server 1.1.1.1 weight=1; server 1.1.1.2 weight=1; server 1.1.1.3 weight=1; } server { listen 443; server_name blah; keepalive_timeout 5; ssl on; ssl_certificate /blah.crt; ssl_certificate_key /blah.key; ssl_session_cache shared:SSL:10m; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; ssl_prefer_server_ciphers on; location / { proxy_pass http://abc; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } The machine is a VPS on Linode with 1 G of RAM. Can anyone please tell why SSL Hand shake is taking ages?

    Read the article

  • Sending bulkmail from different server?

    - by Omer Gencay
    I want to send bulk domains from my vps for a domain(cagetur.com) hosted in another company. The company(cagetur) will go on using the old hosting account for its mailing operations. The vps will just be used for smtp for once a week. I created an A record "vps.cagetur.com". directed it to the IP adress of vps then created a mx record with bigger preference number "50 vps.cagetur.com." on the domain control panel. When I trace the "vps.cagetur.com" i can reach my vps now. I installed hMail on the vps. Configure it (created domain, accounts). I have no information about "system" so i couldn't get further from this point. I can connect to the mail server with Outlook without errors. I can send an email from the account on the vps but it doesn't reaches. No errors, no emails. What do i have to do for getting it work? Thank you.

    Read the article

  • Unable to connect to Windows VPN from iPad

    - by Justin
    I have a 16 GB iPad wifi I can't get to connect to VPN. The error I get is: "A connection could not be established to the PP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator." I have tried a variety of tasks to troubleshoot the issue: I have verified that another iPad on another network can connect to the VPN I am trying to connect to I can connect to this VPN from the same network the iPad uses on a Windows machine I have verified an iPhone user can connect to this VPN from a different network I have reset the iPad's network settings I have reset the entire iPad and restored settings I have compared my settings w/ a screenshot from the iPad that works and confirmed everything is correct I have used the IP address and domain name of our VPN server in the settings I have tried deleting the VPN settings in the iPad and recreating them I have verified in the logs of VPN server that I'm not even getting to the VPN server (no log entry) I have verified that I cannot VPN from the iPad on separate network (different ISP and router) Are there any other ways to troubleshoot VPN on an iPad?

    Read the article

  • Simple way to set up port knocking on Linux?

    - by Ace Paus
    There are well known benefits of Port Knocking utilities when utilized in combination with firewall IP table modification. Port Knocking is best used to provide an additional layer of security over other tools such as the OpenSSH server. I would like some help setting it up on a ubuntu server. I looked at some port knocking implementations here: PORTKNOCKING - A system for stealthy authentication across closed ports. IMPLEMENTATIONS http://www.portknocking.org/view/implementations fwknop looked good. I found an Android client here. And fwknop (both client and server) is in the ubuntu repos. Unfortunately, setting it up (on the server) looks difficult. I do not have iptables set up. My proficiency with iptables is limited (but I understand the basics). I'm looking for a series of simple steps to set it up. I only want to open the SSH port in response to a valid knock. Alternatively, I would consider other port knocking implementations, if they are much simpler to set up and the desired Linux and Android clients are available.

    Read the article

  • What should be monitored to troubleshoot file sharing problems?

    - by RyanW
    I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

    Read the article

< Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >