Search Results

Search found 12645 results on 506 pages for 'maintenance mode'.

Page 402/506 | < Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >

• Setting up a Network Bridge on Linux VM (Windows 7 Host)

  - by GrandAdmiral

  I would like to use NetEm to simulate a low bandwidth environment while testing an Internet-connected device. My plan is to setup a bridge in a Linux VM (Linux Mint 13) on a Windows 7 host. Unfortunately I'm having trouble setting up the bridge. Then I can use NetEm in the Linux VM to limit the bandwidth to an external device. I went with the following script: ifconfig eth0 0.0.0.0 promisc up ifconfig eth1 0.0.0.0 promisc up Then create the bridge and bring it up: brctl addbr br0 brctl setfd br0 0 brctl addif br0 eth0 brctl addif br0 eth1 dhclient br0 ifconfig br0 up When I run that script, I see the following warning: Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service smbd reload Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the reload(8) utility, e.g. reload smbd The device connecting to the bridge is able to obtain an IP Address, but it can only ping the IP Address of the bridge (both are 10.2.32.xx). Then after a few minutes, other parts of our network go down. I'm not sure why, but once I kill the bridge the network is fine. Is it possible to setup a network bridge in a Linux VM? Do I need to do something else with the dhclient br0 part of the script? By the way, I'm using VirtualBox. The wired connection is eth0 and the wireless connection is eth1. The wired connection is connecting to the device and the wireless connection is going to the network. Both adapters are set up as bridged adapters with promiscuous mode set to "allow all".

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• Distortion problem with Creative audio equalizer

  - by e-t172

  Hi, I have a problem with the Creative Console EQ, I don't know if it's fixable or not (is the EQ software or hardware on these cards?). Basically, I have enormous distortion with certain sounds in the 30 - 125 hz range. When this happens I get some sort of "frrzzzz" (sorry, I'm french and don't really know the correct english word for that) on top of the original sound. I have a Sound Blaster Audigy SE. I'm using the Daniel_K drivers, on Windows 7 Profesionnal x64. All the effects are disabled except EQ. Steps to reproduce Put the card in 24bit/96khz mode. The problem is also present with 16bit/48khz but seems to be less audible. In the Creative Console, use the following EQ: (full size) Play this sound at a reasonably high volume. You should hear distortion on the two "booms". Especially the second one. Disable Creative EQ. Play the sound in an application with an integrated EQ (e.g. foobar2000, ffdshow) using the same EQ parameters. There is no distortion. Conclusion: the Creative EQ is broken. Is anyone having the same problem? I'm also interested in the results with other Creative cards or even other brands soundcards with a similar EQ feature.

  Read the article

• Can't connect to EC2 instance Permission denied (publickey)

  - by Assad Ullah

  I got this when I tried to connect my new instace (UBUNTU 12.01 EC2) with my newly generated key sh-3.2# ssh ec2-user@**** -v ****.pem OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to **** [****] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /var/root/.ssh/id_rsa type -1 debug1: identity file /var/root/.ssh/id_rsa-cert type -1 debug1: identity file /var/root/.ssh/id_dsa type -1 debug1: identity file /var/root/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '****' is known and matches the RSA host key. debug1: Found key in /var/root/.ssh/known_hosts:4 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /var/root/.ssh/id_rsa debug1: Trying private key: /var/root/.ssh/id_dsa debug1: No more authentication methods to try.

  Read the article

• Configuring https access on HP A5120 Switch

  - by GerryEgan

  I am trying to configure HTTPS management on a HP a5120 switch running Version 5.20.99, Release 2215 and not having much luck. I have followed the manual by creating an SSL policy first and then enabling the HTTPS server with the SSL policy: ssl server-policy sslpol ip https ssl-server-policy sslpol ip https enable When I try and log onto the switch with Google Chrome I get the following error: Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. When I look this up I have found references to errors due to TLS being used in SSL. I can find no way to specify the SSL version in the server policy. The manual has a configuration example that uses MSCEP to retrieve a certificate but in Windows 2008 R2 that feature is only available in Enterprise and Datacentre editions which I don't have. I have SSH configured and it is using a locally generated certificate so I'm not sure if I can use that but I'd like to if possible. Has anybody been able to setup HTTPS management on HP A series switches without MSCEP? Any and all help appreciated! here is a copy of my config with the interfaces removed: version 5.20.99, Release 2215 # sysname MYSYSNAME # irf domain 10 irf mac-address persistent timer irf auto-update enable undo irf link-delay # domain default enable system # telnet server enable # vlan 1 # vlan 100 description Management # radius scheme system primary authentication 127.0.0.1 1645 primary accounting 127.0.0.1 1646 user-name-format without-domain # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher authorization-attribute level 3 service-type ssh telnet terminal service-type web # stp enable # ssl server-policy sslpol pki-domain MYDOMAIN # interface NULL0 # interface Vlan-interface199 ip address 192.168.199.140 255.255.255.0 # interface GigabitEthernet1/0/1 poe enable stp edged-port enable # interface Ten-GigabitEthernet2/1/2 # dhcp-snooping # ntp-service unicast-server 192.168.1.71 # ssh server enable # ip https ssl-server-policy sslpol ip https enable # load xml-configuration # user-interface aux 0 1 user-interface vty 0 15 authentication-mode scheme

  Read the article

• IIS WebServer CreatesNew file: OwnerShip?

  - by Beaud.

  IIS is configured for Integrated Windows Authentication. web.config is configured as follows: <authentication mode="Windows" /> <identity impersonate="true" /> We are Load balancing between \webserver1 and \webserver2. Windows Server 2003 \\webserverX creates a XML file to \\share1 and access is denied. We got pass through access denial by allowing Everyon to access the share... We would like to have the impersonated user to be the owner of the created file. Instead, \\webserver1's computer account is the owner. How can we make sure that the impersonated user has ownership of the file at creation time? PROGRESSION: I decided to create the file locally on \\webserver1's root directory. File's ownership is NETWORK SERVICES even if impersonate="true". I'm unable to change ownership of the file in C# code. Why when creating a file, IIS won't use the impersonated user's write permissions? If it actually does, what I am doing wrong?

  Read the article

• Completely remove and freshly install MySql on XP?

  - by Corey Ogburn

  I have read this question and have not found it as a solution and I have even attempted much more. I've uninstalled MySql 5.5.18 and deleted: C:\Program Files\MySql C:\Documents and Settings\All Users\Application Data\MySql After uninstalling, I restart the computer. When I reinstall, in the MySql Server Instance Configuration Wizard I leave everything to their defaults except: I add a firewall exception I check Launch MySQL Server Automatically I check Include BIN directory in windows path Enable root access from remote machines (I'll lock that down later, just debugging for now, I have also tried installing without this option to no avail) I've tried Typical and Complete while installing, as well as with and without strict mode. No combination shows a difference. After all this, it cannot Apply Security Settings and I get a 10061 error (it also said error number 2003) and this article didn't help. I've tried everything I can to completely uninstall and successfully reinstall so I can start from scratch. I've uninstalled and reinstalled about a dozen times with minor changes (including turning off the firewall at times), each time deleting the above folders and any proper registry entries with no success. Note by success, applying security settings and a working remote connection. I can connect locally every time, but it's remotely that counts. I have tried to look for exterior problems such as port forwarding in the router and (even though the installer should add it) I do double check the firewall settings, which have always allowed the default port. I'm out of ideas.

  Read the article

• Cannot load from raid with grub

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

  Read the article

• Get Illegal Instruction error when booting Linux in VirtualBox, works fine when booted directly

  - by rkjnsn

  I have a computer on which I am dual booting Windows 7 and Gentoo Linux (both 64-bit). I want to be able to load up my Linux installation in a VM while I am booted into Windows. I have installed VirtualBox and followed the instructions for creating a raw disk VMDK. When I start the VM, Linux starts booting, but then fails with the following error when unlocking my root partition: truecrypt[441] trap invalid opcode ip:373615538e0 sp:3dd0e0dfb60 error:0 in libpixman-1.so.0[373614d6000+8d000] Everything works fine when I boot into Linux directly. What could cause an illegal instruction to be hit in libpixman only when booting in VirtualBox? Update: As a troubleshooting step, I recompiled pixman without "-march", and no longer get an illegal instruction error in that library. (The boot fails in the same spot with the same error in a different library, however.) How can I determine the specific opcode that isn't working in VirtualBox so I can disable it in my CFLAGS without having to disable all CPU-specific optimizations? I am still confused as to why there would be any user-mode instruction that would fail to work in a VM. Is this a known limitation? My CPU is an Intel Core i7 3720QM, and I have hardware virtualization support enabled.

  Read the article

• Anonymous FTP upload on CentOS 5.2

  - by Craig

  I need to allow users to upload files to an FTP server anonymously. They should not be able to see any other files, or download files. It is a CentOS 5.2 server. I have a separate partition for the the upload area (mounted at /ftp). I have tried to set up vsftpd, followed all the instructions/advice I could find. But, when a user logs in and tries to transfer a file it throws a "553 could not create file." error. If I do a 'pwd' it shows the directory as "/" rather than the anon_root of "/ftp/anonymous". Any attempt to change the remote directory ends with "550 Failed to change directory.". I have a subdirectory "/ftp/anonymous/incoming" that is writable for the uploads SELinux is in permissive mode. I am running version 2.0.5 release 16.el5 of vsftpd. Here is the vsftpd.conf file: anonymous_enable=YES local_enable=YES write_enable=YES local_umask=002 anon_umask=007 file_open_mode=0666 anon_upload_enable=YES anon_mkdir_write_enable=NO dirmessage_enable=YES xferlog_enable=YES connect_from_port_20=YES chown_uploads=YES chown_username=inftpadm xferlog_std_format=YES nopriv_user=nobody listen=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES ftp_username=inftpadm anon_root=/ftp/anonymous anon_other_write_enable=NO anon_mkdir_write_enable=NO anon_world_readable_only=NO dirlist_enable=YES Can anyone help?

  Read the article

• Command line scripts to restore the 4 system databases of MS SQL Server 2008

  - by ciscokid

  Hi there, can someone give me some advice on how to restore the 4 system databases (master, msdb, model, tempdb) of a sql server 2008 please? I've already done some testing myself (on restoring the master database) with the following commad line script as a result: ::set variables set dbname=master set dbdirectory=C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA title Restoring %dbname% database net stop mssqlserver cd C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\Binn sqlservr -m sqlcmd -Slocalhost -E -Q "restore database master from disk='c:\master.bak' WITH REPLACE" net start mssqlserver pause After the execution of the 'sqlservr -m' command (used to start the server instance in single-user mode, which is only necessary when restoring the MASTER database), the script stops. So in order to execute the last 2 commands I need to separate the script into 2 smaller scripts, and run them one after the other. Does anyone has an idea on how I can merge them into one single script that runs completely without any interruption? I also want to restore the other 3 system databases using command line scripts like this one. Can someone please advice me how I need to go on? I've already noticed that restoring the temdb is not so easy, but there has to be a way... Looking forward to your advice!

  Read the article

• Vista won't boot. BSOD: Page fault in nonpaged area

  - by user31576

  Here's the story: I let Windows Update do the updates it wanted to do, then rebooted the computer. The updating process was taking time so I went away. When I came back, my computer was rebooting. It got as far as the Windows logo with the laoding bar. BSOD'd. Rebooted. And I'm stuck in this loop ever since. Looked up on the net, the "Page fault in nonpaged area" seems to be linked to faulty RAM or drivers. So I ran a memory test, it found no error. When I try in safe mode (with promt) I can see a list of drivers being loaded, then I get the same BSOD. I tried to repair using the Vista DVD, it says "nothing to repair". I tried to restore to a previous state, it says "no restore point found". So, my guess is, it's got something to do with the drivers. How can I identify the one causing the BSOD? If you have any other leads, What can I do? By the way, I'm writing from this very computer, running a linux distro I installed after the BSOD loop started. So i guess it's not an hardware issue. I have backed up important data, and will format and reinstall Windows if I must. But I'd like to avoid that. Thanks in advance for any help you can give me.

  Read the article

• Configure php mail() on Windows/IIS

  - by Adam Tuttle

  I have a Windows Server 2003 / IIS web server running various application servers, and ended up begrudgingly adding PHP into the mix. I know Win/IIS isn't the ideal environment for PHP, but it's what I've got and I need to make it work. From phpinfo(): Configuration File (php.ini) Path: C:\WINDOWS Loaded Configuration File: C:\php\php.ini From C:\php\php.ini: [mail function] ; For Win32 only. SMTP = localhost smtp_port = 25 ; For Win32 only. ;sendmail_from = [email protected] ; For Unix only. You may supply arguments as well (default: "sendmail -t -i"). ;sendmail_path = ; Force the addition of the specified parameters to be passed as extra parameters ; to the sendmail binary. These parameters will always replace the value of ; the 5th parameter to mail(), even in safe mode. ;mail.force_extra_parameters = Lastly, I have IIS setup to run an SMTP relay that allows connection and relay, but only from localhost. But when I try something that uses mail(), I get this error: The e-mail could not be sent. Possible reason: your host may have disabled the mail() function... Any ideas?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Why is Apache htdigest authentication failing in IE10 on Windows 8?

  - by Kevin Fodness

  One of our developers reported that for the past week or two, the htdigest authentication that we have set up on our test sites in Apache is not working in IE10 on Windows 8. It's fine on IE10 on Windows 7, and it's fine on Chrome on Windows 8. The specific behavior is: Navigate to site with htdigest authentication enabled, username and password form pops up, enter correct username and password, and the username and password box pops up again. Potentially useful information: All patches applied on Windows 8 box No additional software on Windows 8 box other than Outlook 2013 and a browser test suite (Chrome, Firefox, Opera, Chrome Canary, Opera Next) Win8 running in a virtual machine on Xen Same behavior can be replicated on Win8/IE10 on Browserstack.com Server running Ubuntu 10.10 with Apache 2.2.16 This feels like a patch was applied to the Windows box that broke digest authentication for IE10 on Win8 (box configured for automatic updates). However, without knowing a specific date I can't necessarily nail this down. Has anyone else experienced this problem? EDIT: This problem only happens in the "Metro" interface, not when running IE10 in desktop mode. As of a few weeks ago, it worked fine even in the "Metro" interface.

  Read the article

• Gnome-panel disappearance in Ubuntu 10.10

  - by jurchiks

  Just today, after about a week of somewhat normal running (I'm a total beginner in Linux and the level of amazingly stupid problems I encountered made me go nuts), today my panel disappeared (the one with Applications/System menus, you'd call it taskbar in Windows). Also, Alt+F2 doesn't work and Ctrl+Alt+Backspace has no effect (I'd think it's supposed to do something). I tried the solution posted here: Panel doesn't show at startup at Ubuntu 10.04 No luck, didn't change absolutely anything. I also couldn't find the .gconf and .gconfd folders using search, so couldn't try that option. There were ones that had same names but without the dot though, but there were several so I didn't risk. What could possibly be the reason for this? All I did yesterday was try to install some updates (another extremely dumb problem - doesn't allow to install even the official updates - "insecure sources" or smth like that, tried fixing it with some tutorials on the net but in the end it worked only for half a day and went back to refusal mode :@) and very few tools from the Ubuntu Software Center, but nothing that would change system settings just by installing it.

  Read the article

• Routing subnet over GRE tunnel

  - by eMgz

  Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

  Read the article

• Can't ping guest OS from Windows XP SP3 host running VIC.

  - by Vittal

  Hi, I am running VMware ESX Server 3i Version 3.5.0 and accessing this server using VMware Infrastructure Client Version 2.5.0 on a Windows XP SP3 machine. I have enabled the Microsoft TCP/IP version 6 stack and assigned an IPv6 address (using the netsh command) to the network adapter. The guest OS'es running on ESX Server (includes Win7, W2K8, WinXP) also have IPv6 addresses enabled on their adapters. The adapters are configured to be in VM Network (Bridged mode) and hence have connectivity to the Internet. The VMs are able to ping each other using IPv6 addresses and are also able to ping a physical Win7 machine using IPv6 addresses. However, the Windows XP SP3 machine on which the Client is running is not able to ping any hosts running on ESX Server while the VMs are able to ping this host. Whenever I try to ping from WXP box I get the "Invalid source route specified." error. The WinXP machine is not able to ping the Win7 physical machine too (the same error as above is thrown). Can someone help me understand why I am receiving this error and what I need to do to resolve this error? Thanks, Vittal

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  Hello - I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified with SpeakEasy and Speedtest.net) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Unable to browse to apache service, Service is running

  - by Jeff

  Summary I have a very peculiar problem. I am not able to open the "It Works!" page after installing a fresh server with apache. I am able to ssh to the box (from outside the network). Apache seems to be running on my Centos6.4x86_64 box just fine. Nothing useful in /var/logs/httpd/*. What am I missing? The setup I am outside the network right now. The "server" is a VM on my home computer running bridged mode. public ip: A.B.C.D Host: 192.168.1.5 VM: 192.168.1.8 I have a verizon fios router that is forwarding ports 22, 80, and 8888 to the VM. I am able to ssh over port 22, but I am not able to browse to the public URL over port 80. so A.B.C.D:22 is working, but http://A.B.C.D:80 is not. What I've tried nmap to see if it is listening: nmap -sT -O localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-25 11:10 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.000040s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 80/tcp open http 3306/tcp open mysql I tried going to it locally (lynx) and it does work. So, is the problem in my ports?

  Read the article

• Are there any Graphical PowerShell tools?

  - by Dai

  As a developer for the .NET platform, I like to "explore" a platform, framework or API by browsing through the API documentation which explains what everything is - everything is covered and when I use tools like Reflector or Object Browser then I get to know for certain what I'm working with. When I'm writing my own software I can use tools like the Object Test Bench to explore and work with my classes directly. I'm looking for something similar, but for PowerShell - and ones that avoid text-mode. PowerShell is nice, and there are a lot of cool "discoverability"-things it has, such as the "Verb-Noun" syntax, however when I'm working with Exchange Server, for example, I wanted to get a list of AD Permissions on a Receive Connector and I got this list: [PS] C:\Windows\system32>Get-ADPermission "Client SVR6" -User "NT AUTHORITY\Authenticated Users" | fl User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : False AccessRights : {ExtendedRight} IsInherited : False Properties : ChildObjectTypes : InheritedObjectType : InheritanceType : All User : NT AUTHORITY\Authenticated Users Identity : SVR6\Client SVR6 Deny : True AccessRights : {ReadProperty} IsInherited : True Properties : {ms-Exch-Availability-User-Password} ChildObjectTypes : InheritedObjectType : ms-Exch-Availability-Address-Space InheritanceType : Descendents [PS] C:\Windows\system32> Note how the first few entries contain identical text - there's no way to tell them apart easily. But if there was a GUI presumably it would let me drill-down into the differences better. Are there any tools that do this?

  Read the article

• Reconnecting OST with Exchange

  - by syrenity

  Hi. I have a quite big problem with customer's MS Exchange. The server got it's disk filled about 2 weeks ago, so it's currently offline. They plan to upgrade it, but not in hurry, as they use it mainly for OWA and back-up - the mails exchange is done via SMTP and POP3. Trying to diagnose some problem today, one of the users has (following the ISP instructions), removed the Exchange account from Outlook, which essentially left the OST orphaned. The user naturally didn't move the emails or any other data to the Archive / PST before, so these emails located on the OST only. So currently I'm trying to figure out how to restore them. There are 2 options: 1) Make the user buy some tool to convert them to PST, and import as archive / main Outlok file? 2) Reconnect the Outlook to Exchange (once it up), let it sync the old server content, then shutdown Outlook and replace the new OST with the old one, start Outlook again in offline mode and move these files to archive. 3) Any other method? Can someone advice what would be the best approach here? The used versions are Outlook 2007 and Exchange 2003. Thanks!

  Read the article

• Vista Screen resolution Changes when Switching Users

  - by Benjol

  I regularly have a problem when switching between users in Vista - the screen resolution drops down to 800x600. If I try to set the resolution back to the maximum, it says nothing, but just keeps it at 800x600. I can set it back to an intermediate value. Otherwise I have to either restart the PC, or sometimes if I log off one of the users, I can then set the resolution back to max. Might it also have something to do with using sleep mode instead of performing regular shutdowns? I thought it might be related to the desktop background image taking up too much space, but even with plain colours, the problem still occurs. There is an enormous thread on this here, but not really any answers. From what I can gather from that thread, it isn't related to any particular applications, nor limited to a particular make of graphics card or monitor, so I don't think that including hardware details is useful. This is a very annoying problem, as it screws up my desktop and screen layout every single time. Has anyone here experienced this problem or found a solution? I've noticed that Windows Update has tried to install nVidia updates and apparently they've failed on several occasions. Not sure if that is of any relevance or not. UPDATE The last post on the thread: FWIW - I had this problem for about 2 years and wrote a number of posts in this thread in the past. It survived OS reinstallation, change of practically all of my hardware piece by piece (mobo, cpu, monitor, graphics card, memory, power supply...) I used to be affected by this annoying problem at least once every 24-48 hours. About 1.5 months ago I wiped out my 32 bit vista ultimate installation and installed Windows7 ultimate 64 bit from scratch and never saw this problem again. GOOD RIDDANCE. Vista was a pathetic piece of __ that felt like a flashback to the old [horrible] NT4/Windows95 days. I was seriously considering switching over to Apple/Mac OSX if this problem persisted.

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

< Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >