Search Results

Search found 12588 results on 504 pages for 'memory allocation'.

Page 403/504 | < Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >

• Configure 27" 2560x1440 for a monitor with corrupt EDID

  - by Aras

  I am trying to get a monitor work with my Ubuntu laptop. The monitor is this cheap 27" Korean monitors which has a 2560x1440 resolution -- and nothing else. Here are some specifications of this monitor: 2560x1440 @60Hz Only one dual link DVI-D input -- no other input port (no HDMI or display port) no OSD no scalar reports corrupt EDID does 2560x1440 @60Hz, did I say that already? Anyways, the monitor works beautifully with my Ubuntu desktop which has an nVidia card with DVI output. However, I am having problem using this monitor with my laptop. After some searching around I found a few posts suggesting to use an active adaptor for mini display port, so I went and bought a mini display to dual link DVI-D adaptor.. When using this adaptor the monitor is recognized by nvidia-settings tool but with incorrect resolution information. As you can see the monitor is incorrectly recognized and there are no other resolution available to set. This post on ubuntu forums and this other post on overclock both suggest that the monitor is reporting corrupt EDID file. I have tried following their instructions, but so far I have not been able to display any image on the monitor from my laptop. The laptop I am using is an ASUS G75VW with a 1920x1080 screen. It has a VGA, an HDMI 1.4a, and a mini display port. The graphic card is an nvidia gforce gtx 660M with 2GB dedicated memory. I am running Ubuntu 12.10 on here which I upgrade from 12.04 a few weeks ago. As I said I have tried several suggestions, including specifying Modeline in xorg.conf and also linking to EDID files I found from those forum posts above. However, I am not sure if the EDID files I found are suitable for my monitor. I think the solution to my problem consist of obtaining the EDID file of my monitor and then fixing it and modifying xorg.conf to force nvidia driver to load the correct resolution. However, I am not sure what steps I need to take to do this. Here is the part of sudo xrandr --prop output that is related to this monitor: DP-1 connected 800x600+1920+0 (normal left inverted right x axis y axis) 0mm x 0mm SignalFormat: DisplayPort supported: DisplayPort ConnectorType: DisplayPort ConnectorNumber: 3 (0x00000003) _ConnectorLocation: 3 (0x00000003) 800x600 60.3*+ I was expecting to see the EDID file in this output as was mentioned in this post, but it is not there. After several hours of tweaking X configurations, I decided it was time to ask for help here. I would really appreciate if someone with experience regarding EDID and X configuration could give me a hand to solve this issue.

  Read the article

• Exadata support for ACFS (and thus, 10gR2) now available!

  - by Robert Freeman

  Really? Exadata, ACFS and 10gR2? If you work with Exadata you are probably aware that ACFS has not been supported - until now! ACFS is now supported on Exadata if you are running Grid Infrastructure version 12.1.0.2 or later. This new support is described in MOS note 1326938.1. Also Exadata support for ACFS is mentioned in MOS note 888828.1, which is the king of all Exadata notes on MOS. The upshot is that you can now run Oracle Database 10gR2 on Exadata using ACFS as the storage for the Oracle Database. Don’t Over React and just Throw Everything on ACFS!First, let’s be clear that ACFS is not an alternative for running your Exadata databases on ASM. If you are running any production or non-production performance sensitive Oracle databases on 11.2 or 12.1, then you should be running them on ASM disks that are associated with the storage cells. The use case for ACFS is generally limited to the following: Running any Oracle 10gR2 databases on Exadata. Running Oracle 11gR2 development or test databases that require rapid cloning, and that do not require the performance benefits of the Exadata storage cells. If you are running Oracle Database 12c and you need snapshot/clone kinds of capabilities, then you should be using Oracle MultiTennant and the features present in that option (remember though that MultiTennant is a licensed option). The Fine PrintThere are some requirements that you will need to meet If you are going to run ACFS on Exadata. These are: You have to use Oracle Linux You must use GI 12.1.0.2 or later If you wish to use HCC then you must apply the fix for bug 19136936 to your system. This bug, and it’s associated patch do not appear on MOS (as of the time that I wrote this) so you will need to open an SR and get support to provide the patch for you. The Best Use Case for ACFSEven though Oracle Database 10gR2 is at end of life, it remains in use in a large number of places. This has caused problems when choosing to implement Exadata as a consolidation platform, or when choosing it during a hardware refresh process. Now that ACFS is supported, Exadata has become even more flexible and affords customers greater flexibility when migrating to Exadata and Engineered Systems. While all of the features of Exadata might not be available to a 10.2.0.4 database, certainly just the improved processing capabilities of Exadata with its fast as heck infiniband network fabric, additional memory, reduced power requirements and a whole host of other features, justifies moving these databases to Exadata now. This will also make it easier to upgrade these databases when the time comes!

  Read the article

• MAXDOP in SQL Azure

  - by Herve Roggero

  In my search of better understanding the scalability options of SQL Azure I stumbled on an interesting aspect: Query Hints in SQL Azure. More specifically, the MAXDOP hint. A few years ago I did a lot of analysis on this query hint (see article on SQL Server Central:  http://www.sqlservercentral.com/articles/Configuring/managingmaxdegreeofparallelism/1029/).  Here is a quick synopsis of MAXDOP: It is a query hint you use when issuing a SQL statement that provides you control with how many processors SQL Server will use to execute the query. For complex queries with lots of I/O requirements, more CPUs can mean faster parallel searches. However the impact can be drastic on other running threads/processes. If your query takes all available processors at 100% for 5 minutes... guess what... nothing else works. The bottom line is that more is not always better. The use of MAXDOP is more art than science... and a whole lot of testing; it depends on two things: the underlying hardware architecture and the application design. So there isn't a magic number that will work for everyone... except 1... :) Let me explain. The rules of engagements are different. SQL Azure is about sharing. Yep... you are forced to nice with your neighbors.  To achieve this goal SQL Azure sets the MAXDOP to 1 by default, and ignores the use of the MAXDOP hint altogether. That means that all you queries will use one and only one processor.  It really isn't such a bad thing however. Keep in mind that in some of the largest SQL Server implementations MAXDOP is usually also set to 1. It is a well known configuration setting for large scale implementations. The reason is precisely to prevent rogue statements (like a SELECT * FROM HISTORY) from bringing down your systems (like a report that should have been running on a different in the first place) and to avoid the overhead generated by executing too many parallel queries that could cause internal memory management nightmares to the host Operating System. Is summary, forcing the MAXDOP to 1 in SQL Azure makes sense; it ensures that your database will continue to function normally even if one of the other tenants on the same server is running massive queries that would otherwise bring you down. Last but not least, keep in mind as well that when you test your database code for performance on-premise, make sure to set the DOP to 1 on your SQL Server databases to simulate SQL Azure conditions.

  Read the article

• Pixel Perfect Collision Detection in Cocos2dx

  - by Happybirthday

  I am trying to port the pixel perfect collision detection in Cocos2d-x the original version was made for Cocos2D and can be found here: http://www.cocos2d-iphone.org/forums/topic/pixel-perfect-collision-detection-using-color-blending/ Here is my code for the Cocos2d-x version bool CollisionDetection::areTheSpritesColliding(cocos2d::CCSprite *spr1, cocos2d::CCSprite *spr2, bool pp, CCRenderTexture* _rt) { bool isColliding = false; CCRect intersection; CCRect r1 = spr1-boundingBox(); CCRect r2 = spr2-boundingBox(); intersection = CCRectMake(fmax(r1.getMinX(),r2.getMinX()), fmax( r1.getMinY(), r2.getMinY()) ,0,0); intersection.size.width = fmin(r1.getMaxX(), r2.getMaxX() - intersection.getMinX()); intersection.size.height = fmin(r1.getMaxY(), r2.getMaxY() - intersection.getMinY()); // Look for simple bounding box collision if ( (intersection.size.width0) && (intersection.size.height0) ) { // If we're not checking for pixel perfect collisions, return true if (!pp) { return true; } unsigned int x = intersection.origin.x; unsigned int y = intersection.origin.y; unsigned int w = intersection.size.width; unsigned int h = intersection.size.height; unsigned int numPixels = w * h; //CCLog("Intersection X and Y %d, %d", x, y); //CCLog("Number of pixels %d", numPixels); // Draw into the RenderTexture _rt-beginWithClear( 0, 0, 0, 0); // Render both sprites: first one in RED and second one in GREEN glColorMask(1, 0, 0, 1); spr1-visit(); glColorMask(0, 1, 0, 1); spr2-visit(); glColorMask(1, 1, 1, 1); // Get color values of intersection area ccColor4B *buffer = (ccColor4B *)malloc( sizeof(ccColor4B) * numPixels ); glReadPixels(x, y, w, h, GL_RGBA, GL_UNSIGNED_BYTE, buffer); _rt-end(); // Read buffer unsigned int step = 1; for(unsigned int i=0; i 0 && color.g 0) { isColliding = true; break; } } // Free buffer memory free(buffer); } return isColliding; } My code is working perfectly if I send the "pp" parameter as false. That is if I do only a bounding box collision but I am not able to get it working correctly for the case when I need Pixel Perfect collision. I think the opengl masking code is not working as I intended. Here is the code for "_rt" _rt = CCRenderTexture::create(visibleSize.width, visibleSize.height); _rt-setPosition(ccp(origin.x + visibleSize.width * 0.5f, origin.y + visibleSize.height * 0.5f)); this-addChild(_rt, 1000000); _rt-setVisible(true); //For testing I think I am making a mistake with the implementation of this CCRenderTexture Can anyone guide me with what I am doing wrong ? Thank you for your time :)

  Read the article

• Using MAC Authentication for simple Web API’s consumption

  - by cibrax

  For simple scenarios of Web API consumption where identity delegation is not required, traditional http authentication schemas such as basic, certificates or digest are the most used nowadays. All these schemas rely on sending the caller credentials or some representation of it in every request message as part of the Authorization header, so they are prone to suffer phishing attacks if they are not correctly secured at transport level with https. In addition, most client applications typically authenticate two different things, the caller application and the user consuming the API on behalf of that application. For most cases, the schema is simplified by using a single set of username and password for authenticating both, making necessary to store those credentials temporally somewhere in memory. The true is that you can use two different identities, one for the user running the application, which you might authenticate just once during the first call when the application is initialized, and another identity for the application itself that you use on every call. Some cloud vendors like Windows Azure or Amazon Web Services have adopted an schema to authenticate the caller application based on a Message Authentication Code (MAC) generated with a symmetric algorithm using a key known by the two parties, the caller and the Web API. The caller must include a MAC as part of the Authorization header created from different pieces of information in the request message such as the address, the host, and some other headers. The Web API can authenticate the caller by using the key associated to it and validating the attached MAC in the request message. In that way, no credentials are sent as part of the request message, so there is no way an attacker to intercept the message and get access to those credentials. Anyways, this schema also suffers from some deficiencies that can generate attacks. For example, brute force can be still used to infer the key used for generating the MAC, and impersonate the original caller. This can be mitigated by renewing keys in a relative short period of time. This schema as any other can be complemented with transport security. Eran Rammer, one of the brains behind OAuth, has recently published an specification of a protocol based on MAC for Http authentication called Hawk. The initial version of the spec is available here. A curious fact is that the specification per se does not exist, and the specification itself is the code that Eran initially wrote using node.js. In that implementation, you can associate a key to an user, so once the MAC has been verified on the Web API, the user can be inferred from that key. Also a timestamp is used to avoid replay attacks. As a pet project, I decided to port that code to .NET using ASP.NET Web API, which is available also in github under https://github.com/pcibraro/hawknet Enjoy!.

  Read the article

• Web application / Domain model integration using JSON capable DTOs [on hold]

  - by g-makulik

  I'm a bit confused about architectural choices for the web-applications/java/python world. For c/c++ world the available (open source) choices to implement web applications is pretty limited to zero, involving java or python the choices explode to a,- hard to sort out -, mess of available 'frameworks' and application approaches. I want to sort out a clean MVC model, where the M stands for a fully blown (POCO, POJO driven) domain model (according M.Fowler's EAA pattern) using a mature OO language (Java,C++) for implementation. The background is: I have a system with certain hardware components (that introduce system immanent active behavior) and a configuration database for system meta and HW-components configuration data (these are even usually self contained, since the HW-components are capable to persist their configuration data anyway). For realization of the configuration/status data exchange protocol with the HW-components we have chosen the Google Protobuf format, which works well for the directly wired communication with these components. This protocol is already used successfully with a Java based GUI application via TCP/IP connection to the main system controlling HW-component. This application has some drawbacks and design flaws for historical reasons. Now we want to develop an abstract model (domain model) for configuration and monitoring those HW-components, that represents a more use case oriented view to the overall system behavior. I have the feeling that a plain Java class model would fit best for this (c++ implementation seems to have too much implementation/integration overhead with viable language-bridge interfaces). Google Protobuf message definitions could still serve well to describe DTO objects used to interact with a domain model API. But integrating Google Protobuf messages client side for e.g. data binding in the current view doesn't seem to be a good choice. I'm thinking about some extra serialization features, e.g. for JSON based data exchange with the views/controllers. Most lightweight solutions seem to involve a python based presentation layer using JSON based data transfer (I'm at least not sure to be fully informed about this). Is there some lightweight (applicable for a limited ARM Linux platform) framework available, supporting such architecture to realize a web-application? UPDATE: According to my recent research and comments of colleagues I've noticed that using Java (and some JVM) might not be the preferable choice for integration with python on a limited linux system as we have (running on ARM9 with hard to discuss memory and MCU costs), but C/C++ modules would do well for this (since this forms the native interface to python extensions, doesn't it?). I can imagine to provide a domain model from an appropriate C/C++ API (though I still think it's more efforts and higher skill requirements for the involved developers to do with these languages). Still I'm searching for a good approach that supports such architecture. I'll appreciate any pointers!

  Read the article

• SQL SERVER – 2011 – Introduction to SEQUENCE – Simple Example of SEQUENCE

  - by pinaldave

  SQL Server 2011 will contain one of the very interesting feature called SEQUENCE. I have waited for this feature for really long time. I am glad it is here finally. SEQUENCE allows you to define a single point of repository where SQL Server will maintain in memory counter. USE AdventureWorks2008R2 GO CREATE SEQUENCE [Seq] AS [int] START WITH 1 INCREMENT BY 1 MAXVALUE 20000 GO SEQUENCE is very interesting concept and I will write few blog post on this subject in future. Today we will see only working example of the same. Let us create a sequence. We can specify various values like start value, increment value as well maxvalue. -- First Run SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO -- Second Run SELECT NEXT VALUE FOR Seq, c.AccountNumber FROM Sales.Customer c GO Once the sequence is defined, it can be fetched using following method. Every single time new incremental value is provided, irrespective of sessions. Sequence will generate values till the max value specified. Once the max value is reached, query will stop and will return error message. Msg 11728, Level 16, State 1, Line 2 The sequence object ‘Seq’ has reached its minimum or maximum value. Restart the sequence object to allow new values to be generated. We can restart the sequence from any particular value and it will work fine. -- Restart the Sequence ALTER SEQUENCE [Seq] RESTART WITH 1 GO -- Sequence Restarted SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO Let us do final clean up. -- Clean Up DROP SEQUENCE [Seq] GO There are lots of things one can find useful about this feature. We will see that in future posts. Here is the complete code for easy reference. USE AdventureWorks2008R2 GO CREATE SEQUENCE [Seq] AS [int] START WITH 1 INCREMENT BY 1 MAXVALUE 20000 GO -- First Run SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO -- Second Run SELECT NEXT VALUE FOR Seq, c.AccountNumber FROM Sales.Customer c GO -- Restart the Sequence ALTER SEQUENCE [Seq] RESTART WITH 1 GO -- Sequence Restarted SELECT NEXT VALUE FOR Seq, c.CustomerID FROM Sales.Customer c GO -- Clean Up DROP SEQUENCE [Seq] GO Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology

  Read the article

• Dell XPS 15 (L502x) sound problem

  - by lauramolenaar

  I have a problem with my sound on my Dell XPS 15. First, when I had Windows 7, my sound was pretty good (I have a JBL 2.1 speaker system with Waves Maxx audio), but since I installed Ubuntu 12.04 it sounded very cheap and as if I put my laptop in a tin can. I've already tried installing alsa-hda-dkms from the alsa-daily ppa (http://ppa.launchpad.net/ubuntu-audio-dev/alsa-daily) This is my audio controller: laura@laura-XPS-L502X:~$ lspci -v | grep -A7 -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04b6 Flags: bus master, fast devsel, latency 0, IRQ 51 Memory at f1c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel I hope you can help me, and you can always ask me for more information. Result of aplay -l: **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 Result of aplay -L: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC665 Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Digital IEC958 (S/PDIF) Digital Audio Output hdmi:CARD=PCH,DEV=0 HDA Intel PCH, HDMI 0 HDMI Audio Output dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample mixing device dmix:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample mixing device dmix:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample snooping device dsnoop:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample snooping device dsnoop:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct hardware device without any conversions hw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct hardware device without any conversions hw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Hardware device with all software conversions plughw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Hardware device with all software conversions plughw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Hardware device with all software conversions

  Read the article

• EM12c Release 4: Cloud Control to Major Tom...

  - by abulloch

  With the latest release of Enterprise Manager 12c, Release 4 (12.1.0.4) the EM development team has added new functionality to assist the EM Administrator to monitor the health of the EM infrastructure.   Taking feedback delivered from customers directly and through customer advisory boards some nice enhancements have been made to the “Manage Cloud Control” sections of the UI, commonly known in the EM community as “the MTM pages” (MTM stands for Monitor the Monitor).  This part of the EM Cloud Control UI is viewed by many as the mission control for EM Administrators. In this post we’ll highlight some of the new information that’s on display in these redesigned pages and explain how the information they present can help EM administrators identify potential bottlenecks or issues with the EM infrastructure. The first page we’ll take a look at is the newly designed Repository information page.  You can get to this from the main Setup menu, through Manage Cloud Control, then Repository.  Once this page loads you’ll see the new layout that includes 3 tabs containing more drill-down information. The Repository Tab The first tab, Repository, gives you a series of 6 panels or regions on screen that display key information that the EM Administrator needs to review from time to time to ensure that their infrastructure is in good health. Rather than go through every panel let’s call out a few and let you explore the others later yourself on your own EM site.  Firstly, we have the Repository Details panel. At a glance the EM Administrator can see the current version of the EM repository database and more critically, three important elements of information relating to availability and reliability :- Is the database in Archive Log mode ? Is the database using Flashback ? When was the last database backup taken ? In this test environment above the answers are not too worrying, however, Production environments should have at least Archivelog mode enabled, Flashback is a nice feature to enable prior to upgrades (for fast rollback) and all Production sites should have a backup.  In this case the backup information in the Control file indicates there’s been no recorded backups taken. The next region of interest to note on this page shows key information around the Repository configuration, specifically, the initialisation parameters (from the spfile). If you’re storing your EM Repository in a Cluster Database you can view the parameters on each individual instance using the Instance Name drop-down selector in the top right of the region. Additionally, you’ll note there is now a check performed on the active configuration to ensure that you’re using, at the very least, Oracle minimum recommended values.  Should the values in your EM Repository not meet these requirements it will be flagged in this table with a red X for non-compliance.  You can of-course change these values within EM by selecting the Database target and modifying the parameters in the spfile (and optionally, the run-time values if the parameter allows dynamic changes). The last region to call out on this page before moving on is the new look Repository Scheduler Job Status region. This region is an update of a similar region seen on previous releases of the MTM pages in Cloud Control but there’s some important new functionality that’s been added that customers have requested. First-up - Restarting Repository Jobs.  As you can see from the graphic, you can now optionally select a job (by selecting the row in the UI table element) and click on the Restart Job button to take care of any jobs which have stopped or stalled for any reason.  Previously this needed to be done at the command line using EMDIAG or through a PL/SQL package invocation.  You can now take care of this directly from within the UI. Next, you’ll see that a feature has been added to allow the EM administrator to customise the run-time for some of the background jobs that run in the Repository.  We heard from some customers that ensuring these jobs don’t clash with Production backups, etc is a key requirement.  This new functionality allows you to select the pencil icon to edit the schedule time for these more resource intensive background jobs and modify the schedule to avoid clashes like this. Moving onto the next tab, let’s select the Metrics tab. The Metrics Tab There’s some big changes here, this page contains new information regions that help the Administrator understand the direct impact the in-bound metric flows are having on the EM Repository.  Many customers have provided feedback that they are in the dark about the impact of adding new targets or large numbers of new hosts or new target types into EM and the impact this has on the Repository.  This page helps the EM Administrator get to grips with this.  Let’s take a quick look at two regions on this page. First-up there’s a bubble chart showing a comprehensive view of the top resource consumers of metric data, over the last 30 days, charted as the number of rows loaded against the number of collections for the metric.  The size of the bubble indicates a relative volume.  You can see from this example above that a quick glance shows that Host metrics are the largest inbound flow into the repository when measured by number of rows.  Closely following behind this though are a large number of collections for Oracle Weblogic Server and Application Deployment.  Taken together the Host Collections is around 0.7Mb of data.  The total information collection for Weblogic Server and Application Deployments is 0.38Mb and 0.37Mb respectively. If you want to get this information breakdown on the volume of data collected simply hover over the bubble in the chart and you’ll get a floating tooltip showing the information. Clicking on any bubble in the chart takes you one level deeper into a drill-down of the Metric collection. Doing this reveals the individual metric elements for these target types and again shows a representation of the relative cost - in terms of Number of Rows, Number of Collections and Storage cost of data for each Metric type. Looking at another panel on this page we can see a different view on this data. This view shows a view of the Top N metrics (the drop down allows you to select 10, 15 or 20) and sort them by volume of data.  In the case above we can see the largest metric collection (by volume) in this case (over the last 30 days) is the information about OS Registered Software on a Host target. Taken together, these two regions provide a powerful tool for the EM Administrator to understand the potential impact of any new targets that have been discovered and promoted into management by EM12c.  It’s a great tool for identifying the cause of a sudden increase in Repository storage consumption or Redo log and Archive log generation. Using the information on this page EM Administrators can take action to mitigate any load impact by deploying monitoring templates to the targets causing most load if appropriate.   The last tab we’ll look at on this page is the Schema tab. The Schema Tab Selecting this tab brings up a window onto the SYSMAN schema with a focus on Space usage in the EM Repository.  Understanding what tablespaces are growing, at what rate, is essential information for the EM Administrator to stay on top of managing space allocations for the EM Repository so that it works as efficiently as possible and performs well for the users.  Not least because ensuring storage is managed well ensures continued availability of EM for monitoring purposes. The first region to highlight here shows the trend of space usage for the tablespaces in the EM Repository over time.  You can see the upward trend here showing that storage in the EM Repository is being consumed on an upward trend over the last few days here. This is normal as this EM being used here is brand new with Agents being added daily to bring targets into monitoring.  If your Enterprise Manager configuration has reached a steady state over a period of time where the number of new inbound targets is relatively small, the metric collection settings are fairly uniform and standardised (using Templates and Template Collections) you’re likely to see a trend of space allocation that plateau’s. The table below the trend chart shows the Top 20 Tables/Indexes sorted descending by order of space consumed.  You can switch the trend view chart and corresponding detail table by choosing a different tablespace in the EM Repository using the drop-down picker on the top right of this region. The last region to highlight on this page is the region showing information about the Purge policies in effect in the EM Repository. This information is useful to illustrate to EM Administrators the default purge policies in effect for the different categories of information available in the EM Repository.  Of course, it’s also been a long requested feature to have the ability to modify these default retention periods.  You can also do this using this screen.  As there are interdependencies between some data elements you can’t modify retention policies on a feature by feature basis.  Instead, retention policies take categories of information and bundles them together in Groups.  Retention policies are modified at the Group Level.  Understanding the impact of this really deserves a blog post all on it’s own as modifying these can have a significant impact on both the EM Repository’s storage footprint and it’s performance.  For now, we’re just highlighting the features visibility on these new pages. As a user of EM12c we hope the new features you see here address some of the feedback that’s been given on these pages over the past few releases.  We’ll look out for any comments or feedback you have on these pages ! 

  Read the article

• Gain Quick Access to the Cache in Firefox

  - by Asian Angel

  Are you looking for a quick and simple way to view the contents of the cache in Firefox? Then you will definitely want to see how easy it can be using the CacheViewer extension. Note: CacheViewer is a front-end app for easily accessing and searching the memory cache. Before Viewing the cache in Firefox using “about:cache” provides some information about the contents but may not be the most efficient method available for some people. CacheViewer in Action Once you have installed the extension there are three easy ways to access your new cache viewer. The first is using the “CacheViewer Command” available in the “Tools Menu” and the second is using the keyboard shortcut “Ctrl + Shift + C”. The third way is by adding a “Toolbar Button” to your browser’s UI. All three work equally well…choose the method that best suits your personal needs. When you access the “CacheViewer Window” this is what it will look like. You may decide to resize it and move (or hide) some of the columns for the best viewing. You can easily scroll through the cache contents and preview images if desired as shown here. If you keep the “CacheViewer Window” open you can refresh it as you browse using the “Refresh Button” in the lower right corner. This is a nice, quick, and very simple way to access the cache on demand and save items to your hard-drive if desired. Note: The “CacheViewer” can also be set to open in a new tab instead (see “Options”). Options Choose whether “CacheViewer” opens in a separate window (default) or in a new tab. Conclusion If you want a quick and simple way to view the cache in Firefox then the CacheViewer extension is just what you have been looking for. Link Download the CacheViewer extension (Mozilla Add-ons) Similar Articles Productive Geek Tips Add a Cache Clearing Button to FirefoxSearch for Install Packages from the Ubuntu Command LineQuick Tip: Empty Internet Explorer 7 Cache when Browser is ClosedView Internet Explorer Cache Files the Easy WayQuick Hits: 11 Firefox Tab How-Tos TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows SyncToy syncs Files and Folders across Computers on a Network (or partitions on the same drive) If it were only this easy Classic Cinema Online offers 100’s of OnDemand Movies OutSync will Sync Photos of your Friends on Facebook and Outlook

  Read the article

• XMPP— openfire,PHP and python web service

  - by mlakhara

  I am planning to integrate real time notifications into a web application that I am currently working on. I have decided to go with XMPP for this and selected openfire server which i thought to be suitable for my needs. The front end uses strophe library to fetch the notifications using BOSH from my openfire server. However the notices are the notifications and other messages are to be posted by my application and hence I think this code needs to reside at the backend. Initially I thougt of going with PHP XMPP libraries like XMPHP and JAXL but then I think that this would cause much overhead as each script will have to do same steps like connection, authentication etc. and I think this would make the PHP end a little slow and unresponsive. Now I am thinking of creating a middle-ware application acting as a web service that the PHP will call and this application will handle the stuff with XMPP service. The benefit with this is that this app(a server if you will) will have to connect just once and the it will sit there listening on a port. also I am planning to build it in a asynchronous way such that It will first take all the requests from my PHp app and then when there are no more requests; go about doing the notification publishing stuff. I am planninng to create this service in Python using SleekXMPP. This is just what I planned. I am new to XMPP and this whole web service stuff ans would like to take your comments on this regarding issues like memory and CPU usage, advantages, disadvantages, scalability issues,security etc. Thanks in advance. PS:-- also if something like this already exists(although I didn't find after a lot of Googling) Please direct me there. EDIT --- The middle-level service should be doing the following(but not limited to): 1. Publishing notifications for different level of groups and community pages. 2. Notification for single user on some event. 3. User registration(can be done using user service plugin though). EDIT --- Also it should like to create pub-sub nodes and subscribe and unsubscribe users from these pub-sub nodes. Also I want to store the notifications and messages in a database(openfire doesn't). Would that be a good choice?

  Read the article

• Anticipating JavaOne 2012 – Number 17!

  - by Janice J. Heiss

  As I write this, JavaOne 2012 (September 30-October 4 in San Francisco, CA) is just over a week away -- the seventeenth JavaOne! I’ll resist the impulse to travel in memory back to the early days of JavaOne. But I will say that JavaOne is a little like your birthday or New Year’s in that it invites reflection, evaluation, and comparison. It’s a time when we take the temperature of Java and assess the world of information technology generally. At JavaOne, insight and information flow amongst Java developers like no other time of the year.This year, the status of Java seems more secure in the eyes of most Java developers who agree that Oracle is doing an acceptable job of stewarding the platform, and while the story is still in progress, few doubt that Oracle is engaging strongly with the Java community and wants to see Java thrive. From my perspective, the biggest news about Java is the growth of some 250 alternative languages for the JVM – from Groovy to Jython to JRuby to Scala to Clojure and on and on – offering both new opportunities and challenges. The JVM has proven itself to be unusually flexible, resulting in an embarrassment of riches in which, more and more, developers are challenged to find ways to optimally mix together several different languages on projects.    To the matter at hand -- I can say with confidence that Oracle is working hard to make each JavaOne better than the last – more interesting, more stimulating, more networking, and more fun! A great deal of thought and attention is being devoted to the task. To free up time for the 475 technical sessions/Birds of feather/Hands-on-Labs slots, the Java Strategy, Partner, and Technical keynotes will be held on Sunday September 30, beginning at 4:00 p.m.   Let’s not forget Java Embedded@JavaOne which is being held Wednesday, Oct. 3rd and Thursday, Oct. 4th at the Hotel Nikko. It will provide business decision makers, technical leaders, and ecosystem partners important information about Java Embedded technologies and new business opportunities.   This year's JavaOne theme is “Make the Future Java”. So come to JavaOne and make your future better by:--Choosing from 475 sessions given by the experts to improve your working knowledge and coding expertise --Networking with fellow developers in both casual and formal settings--Enjoying world-class entertainment--Delighting in one of the world’s great cities (my home town) Hope to see you there!

  Read the article

• Make the Firefox Awesome Bar Semi-Transparent Like Google Chrome

  - by Matthew Guay

  Would you like to make the Firefox Awesome Bar drop-down menu semi-transparent like in Google Chrome?  Here’s a quick trick that can make your Firefox Awesome Bar a bit more awesome. When you type an address or search query into the address bar in Google Chrome, the drop-down list of history and search suggestions that appears is slightly transparent.  Nothing extreme, but it adds a nice touch. Firefox’s Awesome bar, on the other hand, is fully opaque by default. We can change that with a simple change.  Exit Firefox, then open your Firefox profile folder by entering the following in the address bar in Explorer or in the Run command: %appdata%\Mozilla\Firefox\Profiles\ Open the default folder, and then open the Chrome folder in it. Now, open the userChrome.css file in an editor such as Notepad.  If you do not have a userChrome.css file, open the userChrome-example.css file instead. Now, add the following to the end of the file: #PopupAutoCompleteRichResult[type="autocomplete-richlistbox"]{    opacity: 0.9 !important;} You can change the opacity value, but 0.9 seemed the closest to Chrome’s transparency while keeping the text readable. Save the file as userChrome.css in that same folder.  If you’re editing with Notepad, make sure to select to save as All Files so the file won’t be saved with a .txt extension. Open Firefox, and now your Awesome Bar’s drop-down list will be transparent.  Actually, it may look even more awesome than Google Chrome’s address bar! Conclusion With this simple trick, you can make your Firefox Awesome bar a bit more awesome.  With tweaks like this, it’s no wonder Firefox is still so popular. Special thanks to Daniel Spiewak for the tip! Similar Articles Productive Geek Tips Stupid Geek Tricks: Compare Your Browser’s Memory Usage with Google ChromeHow to Make Google Chrome Your Default BrowserEnable Vista Black Style Theme for Google Chrome in XPMake your Gnome Terminal Background (mostly)Transparent on UbuntuStop YouTube Videos from Automatically Playing in Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 Use ILovePDF To Split and Merge PDF Files TimeToMeet is a Simple Online Meeting Planning Tool Easily Create More Bookmark Toolbars in Firefox Filevo is a Cool File Hosting & Sharing Site Get a free copy of WinUtilities Pro 2010 World Cup Schedule

  Read the article

• Internet doesn't work by default

  - by Adam Martinez

  After upgrading to Precise, I am required to run 'sudo dhclient eth0' in a terminal in order to get the internet to work. Everything worked perfectly fine on Oneiric, so It's really puzzling me. I'm thinking it could possibly be something with the kernel, but who knows. Output of dmesg: [ 0.247891] system 00:01: [io 0x0290-0x030f] has been reserved [ 0.247896] system 00:01: [io 0x0290-0x0297] has been reserved [ 0.247901] system 00:01: [io 0x0880-0x088f] has been reserved [ 0.247908] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.247931] pnp 00:02: [dma 4] [ 0.247935] pnp 00:02: [io 0x0000-0x000f] [ 0.247939] pnp 00:02: [io 0x0080-0x0090] [ 0.247943] pnp 00:02: [io 0x0094-0x009f] [ 0.247947] pnp 00:02: [io 0x00c0-0x00df] [ 0.248033] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.248125] pnp 00:03: [io 0x0070-0x0073] [ 0.248187] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.248205] pnp 00:04: [io 0x0061] [ 0.248260] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.248277] pnp 00:05: [io 0x00f0-0x00ff] [ 0.248292] pnp 00:05: [irq 13] [ 0.248348] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.248583] pnp 00:06: [io 0x03f0-0x03f5] [ 0.248588] pnp 00:06: [io 0x03f7] [ 0.248597] pnp 00:06: [irq 6] [ 0.248601] pnp 00:06: [dma 2] [ 0.248690] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.248998] pnp 00:07: [io 0x03f8-0x03ff] [ 0.249008] pnp 00:07: [irq 4] [ 0.249122] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.249479] pnp 00:08: [io 0x0400-0x04bf] [ 0.249584] system 00:08: [io 0x0400-0x04bf] has been reserved [ 0.249591] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.249628] pnp 00:09: [mem 0xffb80000-0xffbfffff] [ 0.249690] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) [ 0.250049] pnp 00:0a: [mem 0xe0000000-0xefffffff] [ 0.250167] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved [ 0.250173] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.250302] pnp 00:0b: [mem 0x000f0000-0x000fffff] [ 0.250307] pnp 00:0b: [mem 0x7ff00000-0x7fffffff] [ 0.250311] pnp 00:0b: [mem 0xfed00000-0xfed000ff] [ 0.250316] pnp 00:0b: [mem 0x0000046e-0x0000056d] [ 0.250320] pnp 00:0b: [mem 0x7fee0000-0x7fefffff] [ 0.250324] pnp 00:0b: [mem 0x00000000-0x0009ffff] [ 0.250328] pnp 00:0b: [mem 0x00100000-0x7fedffff] [ 0.250332] pnp 00:0b: [mem 0xfec00000-0xfec00fff] [ 0.250336] pnp 00:0b: [mem 0xfed14000-0xfed1dfff] [ 0.250341] pnp 00:0b: [mem 0xfed20000-0xfed9ffff] [ 0.250345] pnp 00:0b: [mem 0xfee00000-0xfee00fff] [ 0.250349] pnp 00:0b: [mem 0xffb00000-0xffb7ffff] [ 0.250353] pnp 00:0b: [mem 0xfff00000-0xffffffff] [ 0.250357] pnp 00:0b: [mem 0x000e0000-0x000effff] [ 0.250409] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0007ffff pref] [ 0.250419] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref] [ 0.250430] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:04:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.250524] system 00:0b: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.250530] system 00:0b: [mem 0x7ff00000-0x7fffffff] has been reserved [ 0.250536] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved [ 0.250541] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved [ 0.250547] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.250552] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved [ 0.250558] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.250563] system 00:0b: [mem 0xfed14000-0xfed1dfff] has been reserved [ 0.250568] system 00:0b: [mem 0xfed20000-0xfed9ffff] has been reserved [ 0.250574] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.250579] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved [ 0.250585] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved [ 0.250590] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved [ 0.250596] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.250614] pnp: PnP ACPI: found 12 devices [ 0.250617] ACPI: ACPI bus type pnp unregistered [ 0.250624] PnPBIOS: Disabled by ACPI PNP [ 0.288725] PCI: max bus depth: 1 pci_try_num: 2 [ 0.288786] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref] [ 0.288792] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.288797] pci 0000:00:01.0: bridge window [io 0xa000-0xafff] [ 0.288804] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff] [ 0.288811] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.288820] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 0.288825] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] [ 0.288833] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.288840] pci 0000:00:1c.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.288851] pci 0000:03:00.0: BAR 6: assigned [mem 0xfde00000-0xfde0ffff pref] [ 0.288856] pci 0000:00:1c.4: PCI bridge to [bus 03-03] [ 0.288861] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff] [ 0.288869] pci 0000:00:1c.4: bridge window [mem 0xfd700000-0xfd7fffff] [ 0.288876] pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.288887] pci 0000:04:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref] [ 0.288891] pci 0000:00:1c.5: PCI bridge to [bus 04-04] [ 0.288897] pci 0000:00:1c.5: bridge window [io 0xb000-0xbfff] [ 0.288904] pci 0000:00:1c.5: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.288911] pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.288920] pci 0000:00:1e.0: PCI bridge to [bus 05-05] [ 0.288926] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff] [ 0.288933] pci 0000:00:1e.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.288940] pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.288971] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288979] pci 0000:00:01.0: setting latency timer to 64 [ 0.288991] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288998] pci 0000:00:1c.0: setting latency timer to 64 [ 0.289008] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.289014] pci 0000:00:1c.4: setting latency timer to 64 [ 0.289030] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.289037] pci 0000:00:1c.5: setting latency timer to 64 [ 0.289047] pci 0000:00:1e.0: setting latency timer to 64 [ 0.289054] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.289058] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.289063] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289067] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289072] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289077] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.289081] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff] [ 0.289086] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.289092] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff] [ 0.289096] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff] [ 0.289101] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.289106] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.289110] pci_bus 0000:03: resource 1 [mem 0xfd700000-0xfd7fffff] [ 0.289115] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.289120] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.289124] pci_bus 0000:04: resource 1 [mem 0xfdd00000-0xfddfffff] [ 0.289129] pci_bus 0000:04: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.289134] pci_bus 0000:05: resource 0 [io 0xc000-0xcfff] [ 0.289138] pci_bus 0000:05: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.289143] pci_bus 0000:05: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.289148] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7] [ 0.289152] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff] [ 0.289157] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289161] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289166] pci_bus 0000:05: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289233] NET: Registered protocol family 2 [ 0.289360] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.289754] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.290351] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.290670] TCP: Hash tables configured (established 131072 bind 65536) [ 0.290674] TCP reno registered [ 0.290680] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.290703] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.290868] NET: Registered protocol family 1 [ 0.290911] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.290932] pci 0000:00:1a.0: PCI INT A disabled [ 0.290956] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.290975] pci 0000:00:1a.1: PCI INT B disabled [ 0.290992] pci 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.291012] pci 0000:00:1a.2: PCI INT D disabled [ 0.291031] pci 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291068] pci 0000:00:1a.7: PCI INT C disabled [ 0.291104] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291123] pci 0000:00:1d.0: PCI INT A disabled [ 0.291135] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.291155] pci 0000:00:1d.1: PCI INT B disabled [ 0.291166] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291185] pci 0000:00:1d.2: PCI INT C disabled [ 0.291198] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291219] pci 0000:00:1d.7: PCI INT A disabled [ 0.291258] pci 0000:01:00.0: Boot video device [ 0.291273] PCI: CLS 4 bytes, default 64 [ 0.291857] audit: initializing netlink socket (disabled) [ 0.291876] type=2000 audit(1336753420.284:1): initialized [ 0.337724] highmem bounce pool size: 64 pages [ 0.337734] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.349241] VFS: Disk quotas dquot_6.5.2 [ 0.349365] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.350418] fuse init (API version 7.17) [ 0.350611] msgmni has been set to 1685 [ 0.351179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.351229] io scheduler noop registered [ 0.351233] io scheduler deadline registered [ 0.351247] io scheduler cfq registered (default) [ 0.351450] pcieport 0000:00:01.0: setting latency timer to 64 [ 0.351502] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X [ 0.351585] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.351639] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X [ 0.351728] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.351779] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 0.351875] pcieport 0000:00:1c.5: setting latency timer to 64 [ 0.351927] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X [ 0.352094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.352143] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.352311] intel_idle: MWAIT substates: 0x22220 [ 0.352315] intel_idle: does not run on family 6 model 23 [ 0.352446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 0.352455] ACPI: Power Button [PWRB] [ 0.352556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.352562] ACPI: Power Button [PWRF] [ 0.352650] ACPI: Fan [FAN] (on) [ 0.355667] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.355673] ACPI: Thermal Zone [THRM] (26 C) [ 0.355750] ERST: Table is not found! [ 0.355753] GHES: HEST is not enabled! [ 0.355898] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.376332] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.376582] isapnp: Scanning for PnP cards... [ 0.709133] Freeing initrd memory: 13792k freed [ 0.729743] isapnp: No Plug & Play device found [ 0.816786] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.832385] Linux agpgart interface v0.103 [ 0.835605] brd: module loaded [ 0.837138] loop: module loaded [ 0.837452] ata_piix 0000:00:1f.2: version 2.13 [ 0.837473] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.837480] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.837546] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.838099] scsi0 : ata_piix [ 0.838253] scsi1 : ata_piix [ 0.839183] ata1: SATA max UDMA/133 cmd 0xf900 ctl 0xf800 bmdma 0xf500 irq 19 [ 0.839192] ata2: SATA max UDMA/133 cmd 0xf700 ctl 0xf600 bmdma 0xf508 irq 19 [ 0.839239] ata_piix 0000:00:1f.5: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.839246] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.839300] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.839708] scsi2 : ata_piix [ 0.839841] scsi3 : ata_piix [ 0.840301] ata3: SATA max UDMA/133 cmd 0xf200 ctl 0xf100 bmdma 0xee00 irq 19 [ 0.840308] ata4: SATA max UDMA/133 cmd 0xf000 ctl 0xef00 bmdma 0xee08 irq 19 [ 0.840429] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.840467] pata_acpi 0000:03:00.0: setting latency timer to 64 [ 0.840488] pata_acpi 0000:03:00.0: PCI INT A disabled [ 0.841159] Fixed MDIO Bus: probed [ 0.841205] tun: Universal TUN/TAP device driver, 1.6 [ 0.841210] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.841322] PPP generic driver version 2.4.2 [ 0.841515] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.841542] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.841567] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.841573] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.841658] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.845582] ehci_hcd 0000:00:1a.7: cache line size of 4 is not supported [ 0.845610] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000 [ 0.860022] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.860264] hub 1-0:1.0: USB hub found [ 0.860272] hub 1-0:1.0: 6 ports detected [ 0.860404] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.860424] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.860430] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.860512] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.864413] ehci_hcd 0000:00:1d.7: cache line size of 4 is not supported [ 0.864438] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000 [ 0.880021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.880227] hub 2-0:1.0: USB hub found [ 0.880234] hub 2-0:1.0: 6 ports detected [ 0.880369] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.880396] uhci_hcd: USB Universal Host Controller Interface driver [ 0.880431] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.880443] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.880449] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.880529] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.880574] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff00 [ 0.880803] hub 3-0:1.0: USB hub found [ 0.880811] hub 3-0:1.0: 2 ports detected [ 0.880929] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.880940] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.880946] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.881039] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.881081] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fe00 [ 0.881302] hub 4-0:1.0: USB hub found [ 0.881310] hub 4-0:1.0: 2 ports detected [ 0.881427] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.881438] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.881443] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.881523] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.881551] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fd00 [ 0.881774] hub 5-0:1.0: USB hub found [ 0.881781] hub 5-0:1.0: 2 ports detected [ 0.881899] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.881910] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.881915] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.881993] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.882021] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00 [ 0.882244] hub 6-0:1.0: USB hub found [ 0.882252] hub 6-0:1.0: 2 ports detected [ 0.882370] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.882381] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.882386] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.882467] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.882495] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00 [ 0.882735] hub 7-0:1.0: USB hub found [ 0.882742] hub 7-0:1.0: 2 ports detected [ 0.882858] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.882869] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.882875] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.882954] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.882982] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fa00 [ 0.883205] hub 8-0:1.0: USB hub found [ 0.883213] hub 8-0:1.0: 2 ports detected [ 0.883435] usbcore: registered new interface driver libusual [ 0.883535] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.883926] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.883936] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.884187] mousedev: PS/2 mouse device common for all mice [ 0.884433] rtc_cmos 00:03: RTC can wake from S4 [ 0.884582] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 0.884612] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.884719] device-mapper: uevent: version 1.0.3 [ 0.884854] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 0.884917] EISA: Probing bus 0 at eisa.0 [ 0.884921] EISA: Cannot allocate resource for mainboard [ 0.884925] Cannot allocate resource for EISA slot 1 [ 0.884929] Cannot allocate resource for EISA slot 2 [ 0.884932] Cannot allocate resource for EISA slot 3 [ 0.884936] Cannot allocate resource for EISA slot 4 [ 0.884940] Cannot allocate resource for EISA slot 5 [ 0.884943] Cannot allocate resource for EISA slot 6 [ 0.884947] Cannot allocate resource for EISA slot 7 [ 0.884950] Cannot allocate resource for EISA slot 8 [ 0.884954] EISA: Detected 0 cards. [ 0.884969] cpufreq-nforce2: No nForce2 chipset. [ 0.884973] cpuidle: using governor ladder [ 0.884976] cpuidle: using governor menu [ 0.884980] EFI Variables Facility v0.08 2004-May-17 [ 0.885476] TCP cubic registered [ 0.885708] NET: Registered protocol family 10 [ 0.886771] NET: Registered protocol family 17 [ 0.886799] Registering the dns_resolver key type [ 0.886837] Using IPI No-Shortcut mode [ 0.887028] PM: Hibernation image not present or could not be loaded. [ 0.887047] registered taskstats version 1 [ 0.902579] Magic number: 12:339:388 [ 0.902592] usb usb6: hash matches [ 0.902687] rtc_cmos 00:03: setting system clock to 2012-05-11 16:23:41 UTC (1336753421) [ 0.903185] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.903189] EDD information not available. [ 1.170710] ata3: SATA link down (SStatus 0 SControl 300) [ 1.181439] ata4: SATA link down (SStatus 0 SControl 300) [ 1.288020] Refined TSC clocksource calibration: 2499.999 MHz. [ 1.288028] Switching to clocksource tsc [ 1.292016] usb 1-5: new high-speed USB device number 3 using ehci_hcd [ 1.486745] ata2.00: SATA link down (SStatus 0 SControl 300) [ 1.486762] ata2.01: SATA link down (SStatus 0 SControl 300) [ 1.640115] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.640130] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.648342] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133 [ 1.648348] ata1.00: 490234752 sectors, multi 0: LBA48 [ 1.664325] ata1.00: configured for UDMA/133 [ 1.664531] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5 [ 1.664745] sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB) [ 1.664809] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.664838] sd 0:0:0:0: [sda] Write Protect is off [ 1.664843] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.664884] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.691699] sda: sda1 sda2 sda3 sda4 [ 1.692348] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.692461] Freeing unused kernel memory: 740k freed [ 1.692820] Write protecting the kernel text: 5828k [ 1.692851] Write protecting the kernel read-only data: 2376k [ 1.692854] NX-protecting the kernel data: 4412k [ 1.723980] udevd[92]: starting version 175 [ 1.865339] Floppy drive(s): fd0 is 1.44M [ 1.865429] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.865478] pata_jmicron 0000:03:00.0: setting latency timer to 64 [ 1.867875] sky2: driver version 1.30 [ 1.867926] sky2 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.867942] sky2 0000:04:00.0: setting latency timer to 64 [ 1.867979] sky2 0000:04:00.0: Yukon-2 EC chip revision 2 [ 1.868111] sky2 0000:04:00.0: irq 44 for MSI/MSI-X [ 1.868174] scsi4 : pata_jmicron [ 1.869802] sky2 0000:04:00.0: eth0: addr 00:01:29:a4:16:0a [ 1.869828] scsi5 : pata_jmicron [ 1.869943] ata5: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16 [ 1.869949] ata6: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16 [ 1.880053] usb 4-1: new full-speed USB device number 2 using uhci_hcd [ 1.884052] FDC 0 is a post-1991 82077 [ 2.032611] ata5.00: ATAPI: _NEC DVD+/-RW ND-3450A, 103C, max UDMA/33 [ 2.048585] ata5.00: configured for UDMA/33 [ 2.049777] scsi 4:0:0:0: CD-ROM _NEC DVD+-RW ND-3450A 103C PQ: 0 ANSI: 5 [ 2.051048] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 2.051054] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.051283] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 2.051483] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 2.079838] usbcore: registered new interface driver usbhid [ 2.079844] usbhid: USB HID core driver [ 2.236660] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 12.150230] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.177342] udevd[333]: starting version 175 [ 12.195524] Adding 417684k swap on /dev/sda2. Priority:-1 extents:1 across:417684k [ 12.278032] lp: driver loaded but no devices found [ 12.516456] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.1-1/input2 [ 12.520297] input: Logitech Unifying Device. Wireless PID:1024 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input2 [ 12.520753] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1024] on usb-0000:00:1a.1-1:1 [ 12.523286] input: Logitech Unifying Device. Wireless PID:2011 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input3 [ 12.524439] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2011] on usb-0000:00:1a.1-1:2 [ 12.545746] type=1400 audit(1336771433.137:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=502 comm="apparmor_parser" [ 12.546574] type=1400 audit(1336771433.137:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=502 comm="apparmor_parser" [ 12.547034] type=1400 audit(1336771433.137:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=502 comm="apparmor_parser" [ 12.626869] Linux video capture interface: v2.00 [ 12.649104] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081a) [ 12.668665] input: UVC Camera (046d:081a) as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input4 [ 12.668909] usbcore: registered new interface driver uvcvideo [ 12.668914] USB Video Class driver (1.1.1) [ 12.697645] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 12.697721] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 12.697760] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 12.706772] nvidia: module license 'NVIDIA' taints kernel. [ 12.706778] Disabling lock debugging due to kernel taint [ 12.735428] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 13.350252] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 13.350267] nvidia 0000:01:00.0: setting latency timer to 64 [ 13.350275] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 13.351464] NVRM: loading NVIDIA UNIX x86 Kernel Module 295.40 Thu Apr 5 21:28:09 PDT 2012 [ 13.356785] hda_codec: ALC889A: BIOS auto-probing. [ 13.357267] init: failsafe main process (658) killed by TERM signal [ 13.372756] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 [ 13.373173] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 13.373568] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 13.373954] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 13.374339] input: HDA Intel Line-Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 13.374715] input: HDA Intel Line-Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 13.375109] input: HDA Intel Line-Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 13.375724] input: HDA Intel Line-Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 13.475252] type=1400 audit(1336771434.065:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=735 comm="apparmor_parser" [ 13.477026] type=1400 audit(1336771434.069:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=735 comm="apparmor_parser" [ 13.477695] type=1400 audit(1336771434.069:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=735 comm="apparmor_parser" [ 13.479048] type=1400 audit(1336771434.069:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=734 comm="apparmor_parser" [ 13.488994] type=1400 audit(1336771434.081:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=738 comm="apparmor_parser" [ 13.489972] type=1400 audit(1336771434.081:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=738 comm="apparmor_parser" [ 13.

  Read the article

• Playing NSF music in FMOD.net

  - by Tesserex

  So, as the title says, I want to be able to play NSF files using FMOD, because my project already uses FMOD and I'd rather not replace it. This will involve figuring out how existing players and emulators work and porting it. I haven't yet found an existing player that uses FMOD. My starting point is the MyNes source from http://sourceforge.net/projects/mynes/. There are two big steps between here and what I'm looking for. MyNes plays from a ROM, not NSF. So, I have to rip out the APU and get it to play NSF files. The MyNes APU uses SlimDX, so I have to convert that to FMOD.NET. I am really stuck about how to go about either of these, because I'm not that familiar with audio formats and it's hard finding resources online. So here are a few questions: From what I can tell from the NSF spec at http://kevtris.org/nes/nsfspec.txt, it's just contains the relevant memory section of the ROM, plus the header. If anyone can verify or correct this that would be great. The emulator APU uses data from the rest of the emulator to play, including things like cycle counts. I'm not sure what replaces this in a standalone player. Can't I just load all the music data at once into a stream and play it? Joining #1 and #2, does the header data from the NSF substitute for some of the ROM data in the emulator code? Using FMOD, will I be following the usercreatedsound example for loading a stream? And does this format count as PCM? Specifically MyNes says PCM8. Any tips on loading / playing the stream in FMOD are appreciated. As an aside, I don't really understand the loading / playing sections of the spec I linked at all. It seems to apply to 6502 systems / emulators only and not to my situation. I know it's a long shot for anyone here to have enough experience in this area to help, but anything you can provide is definitely appreciated. A link to an existing .NET library that does this would be even better, but I don't believe one exists.

  Read the article

• Changing the default installation path to a newly installed hard disk

  - by mgj

  Hi, I am currently working on a dual-booted PC. I am using Windows XP and Ubuntu 10.04 Lucid Lynx released in April 2010. The allocated partition to Ubuntu that I am making use of has almost exhausted. Current memory allocations on the PC wrt Ubuntu OS looks like this: bodhgaya@pc146724-desktop:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 8.6G 8.0G 113M 99% / none 998M 268K 998M 1% /dev none 1002M 580K 1002M 1% /dev/shm none 1002M 100K 1002M 1% /var/run none 1002M 0 1002M 0% /var/lock none 1002M 0 1002M 0% /lib/init/rw /dev/sda1 25G 16G 9.8G 62% /media/C /dev/sdb1 37G 214M 35G 1% /media/ubuntulinuxstore bodhgaya@pc146724-desktop:~$ cd /tmp I am trying to mount a 40GB(/dev/sdb1 - given below) new hard disk along with my existing Ubuntu system to overcome with hard disk space related issues. I referred to the following tutorial to mount a new hard disk onto the system:- http://www.smorgasbord.net/how-to-in...untu-linux%20/ I was able to successfully mount this hard disk for Ubuntu 0S. I have this new hard disk setup in /media/ubuntulinuxstore directory. The current partition in my system looks like this: bodhgaya@pc146724-desktop:/media/ubuntulinuxstore$ sudo fdisk -l [sudo] password for bodhgaya: Disk /dev/sda: 40.0 GB, 40000000000 bytes 255 heads, 63 sectors/track, 4863 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x446eceb5 Device Boot Start End Blocks Id System /dev/sda1 * 2 3264 26210047+ 7 HPFS/NTFS /dev/sda2 3265 4385 9004432+ 83 Linux /dev/sda3 4386 4863 3839535 82 Linux swap / Solaris Disk /dev/sdb: 40.0 GB, 40000000000 bytes 255 heads, 63 sectors/track, 4863 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfa8afa8a Device Boot Start End Blocks Id System /dev/sdb1 1 4862 39053983+ 7 HPFS/NTFS bodhgaya@pc146724-desktop:/media/ubuntulinuxstore$ Now, I have a concern wrt the "location" where the new softwares will be installed. Generally softwares are installed via the terminal and by default a fixed path is used to where the post installation set up files can be found (I am talking in context of the drive). This is like the typical case of Windows, where softwares by default are installed in the C: drive. These days people customize their installations to a drive which they find apt to serve their purpose (generally based on availability of hard disk space). I am trying to figure out how to customize the same for Ubuntu. As we all know the most softwares are installed via commands given from the Terminal. My road block is how do I redirect the default path set on the terminal where files get installed to this new hard disk. This if done will help me overcome space constraints I am currently facing wrt the partition on which my Ubuntu is initially installed. I would also by this, save time on not formatting my system and reinstalling Ubuntu and other softwares all over again. Please help me with this, your suggestions are much appreciated.

  Read the article

• Dual booting 12.10 and Win 7 - boots directly to Win 7

  - by user110174

  and thank you kindly for you help! I'll preface this with saying that I realize this is a common problem, with lots of trouble-shooting guides available online; however, after multiple attempts with different guides, I've made zero progress and am hoping to someone could help me with my specific scenario. First, my story: -Initially, I installed Ubuntu 12.10 with the "Something Else" option with no problems. Used 4 GB Swap Logical Partition, 26 GB Primary Root Partition. Wanting to trying out Mint 13, I booted into Windows from GRUB2, used the latest version of EasyBCD (v2.2) to restore the Windows 7 bootloader to the MBR, deleted the Ubuntu partitions, reformatted them in NTFS. I then created a 30 GB partition of free space for Mint. I installed Mint using the same partitioning described above for Ubuntu 12.10, using /dev/sda for the boot installation files, and everything seemed to go well, until I re-booted my computer and it went straight to Windows - I could find no way to get into Mint. So I went into windows, restored windows bootloader to the MBR w/ EasyBCD, deleted partitions, etc., as I figured I'd done enough messing around and would go with Ubuntu 12.10. Now the problem: I restarted my computer booting from the same Ubuntu USB key I originally used. Briefly, "error: "prefix" is not set" flashed on screen, and instead of being greeted with the GUI menu of "try vs. install Ubuntu", there was a menu with minimal graphics (like a BIOS menu) where I could select install, run from USB, etc. After selecting "Install Ubuntu", the familiar install wizard with a GUI came up, I partitioned my drive as described, /dev/sda for the boot installation files, install went well, rebooted and...straight to Windows. This is where I'm at. Fixes I've tried: -This guide: How can I repair grub? (How to get Ubuntu back after installing Windows?) to ensure Grub is on the MBR. I followed all steps, but still when I reboot, I go directly into Windows. -Installing 12.04 instead of 12.10 - same issue -Re-installed Ubuntu, writing the boot files to their own partition, then using EasyBCD to to add a boot option for Ubuntu using the Windows bootloader, ensuring I instruct EasyBCD to look at the partition I created with the Ubuntu installer (instructions here http://neosmart.net/wiki/display/EBCD/Ubuntu). When I reboot, I select the Ubuntu option, and it puts me in GRUB4DOS, with a cursor waiting for input. I have no idea what to put here, so I would just type "reboot" to exit out. And this is where I am now. Any clue as to why I can't boot into Ubuntu? My computer specs are: ASUS UX31A Core i7, Win 7 64 Pro, 256 GB SSD, Intel HM76 Chipset and Integrated Intel HD 4000 Graphics, 4 GB memory I've tried to be as clear as possible, but I'd be happy to provide any info that would help anyone along. Thanks for your patience in reading this! Sincerely, -MN

  Read the article

• mysql completely removing

  - by Dmitry Teplyakov

  I broke my mysql and now I want to completely reinstall it. I tried: $ sudo apt-get install --reinstall mysql-server $ sudo apt-get remove --purge mysql-client mysql-server But always I see popup with proposal to change root password, I change it and got an error that I can change it.. $ sudo apt-get remove --purge mysql-client mysql-server Reading package lists... Done Building dependency tree Reading state information... Done Package mysql-client is not installed, so not removed Package mysql-server is not installed, so not removed The following packages were automatically installed and are no longer required: libmygpo-qt1 libqtscript4-network libqtscript4-gui libtag-extras1 libqtscript4-sql libqtscript4-xml amarok-utils amarok-common libqtscript4-uitools liblastfm0 libloudmouth1-0 libqtscript4-core Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up mysql-server-5.5 (5.5.28-0ubuntu0.12.04.2) ... 121114 19:04:03 [Note] Plugin 'FEDERATED' is disabled. 121114 19:04:03 InnoDB: The InnoDB memory heap is disabled 121114 19:04:03 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121114 19:04:03 InnoDB: Compressed tables use zlib 1.2.3.4 121114 19:04:03 InnoDB: Initializing buffer pool, size = 128.0M 121114 19:04:03 InnoDB: Completed initialization of buffer pool InnoDB: Error: auto-extending data file ./ibdata1 is of a different size InnoDB: 0 pages (rounded down to MB) than specified in the .cnf file: InnoDB: initial 640 pages, max 0 (relevant if non-zero) pages! 121114 19:04:03 InnoDB: Could not open or create data files. 121114 19:04:03 InnoDB: If you tried to add new data files, and it failed here, 121114 19:04:03 InnoDB: you should now edit innodb_data_file_path in my.cnf back 121114 19:04:03 InnoDB: to what it was, and remove the new ibdata files InnoDB created 121114 19:04:03 InnoDB: in this failed attempt. InnoDB only wrote those files full of 121114 19:04:03 InnoDB: zeros, but did not yet use them in any way. But be careful: do not 121114 19:04:03 InnoDB: remove old data files which contain your precious data! 121114 19:04:03 [ERROR] Plugin 'InnoDB' init function returned error. 121114 19:04:03 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121114 19:04:03 [ERROR] Unknown/unsupported storage engine: InnoDB 121114 19:04:03 [ERROR] Aborting 121114 19:04:03 [Note] /usr/sbin/mysqld: Shutdown complete start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: mysql-server-5.5 E: Sub-process /usr/bin/dpkg returned an error code (1) It is good for me that I have not any important databases, but..

  Read the article

• 10.10 freezing when sftp downloading

  - by aGr

  My ubuntu 10.10 is freezing during downloading from my other computer on sftp. I thought it might be some nautilus issues so I tried it via command line and I got the same thing - after few minutes the whole computer freezes. Mostly the numlock led is blinking (I've heard somewhere that this means a kernel panic), but not in 100% cases. I dunno if that helps but here is a log from /var/log/message in the time that this happened. At least I hope so - it wasn't that big, when it happened before. But this looks quite "errorish", right? (isn't complete - see bottom) Jan 5 17:57:49 tomas-ntb kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 5 17:57:49 tomas-ntb rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="953" x-info="http://www.rsyslog.com"] (re)start Jan 5 17:57:49 tomas-ntb rsyslogd: rsyslogd's groupid changed to 103 Jan 5 17:57:49 tomas-ntb rsyslogd: rsyslogd's userid changed to 101 Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Initializing cgroup subsys cpuset Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Initializing cgroup subsys cpu Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Linux version 2.6.35-24-generic (buildd@vernadsky) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #42-Ubuntu SMP Thu Dec 2 01:41:57 UTC 2010 (Ubuntu 2.6.35-24.42-generic 2.6.35.8) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-provided physical RAM map: Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dffa8000 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dffa8000 - 00000000dffb0000 (ACPI NVS) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dffb0000 - 00000000dffbff00 (ACPI data) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dffbff00 - 00000000dfff0000 (ACPI NVS) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dfff0000 - 00000000e0000000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000120000000 - 0000000140000000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel! Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] DMI 2.5 present. Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] last_pfn = 0xdffa8 max_arch_pfn = 0x100000 Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Scanning 0 areas for low memory corruption Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified physical RAM map: Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 0000000000010000 - 000000000009e800 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 000000000009e800 - 00000000000a0000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 0000000000100000 - 00000000dffa8000 (usable) ... to long - for whole and better view click here

  Read the article

• NEC Corporation uPD720200 USB 3.0 controller doesn't run at full speed

  - by Radek Zyskowski

  I have fresh install of Ubuntu 10.10. I have external HD on USB 3.0. Trying to connect this via PCI Express NEC controller. dmesg: [ 8966.820078] usb 6-3: new high speed USB device using xhci_hcd and address 0 [ 8966.839831] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.840580] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.841329] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.842079] xhci_hcd 0000:02:00.0: WARN: short transfer on control ep [ 8966.843343] scsi8 : usb-storage 6-3:1.0 [ 8967.847144] scsi 8:0:0:0: Direct-Access SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5 [ 8967.847589] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 8967.847923] sd 8:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 8967.848341] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.850959] sd 8:0:0:0: [sdb] Write Protect is off [ 8967.850963] sd 8:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 8967.850966] sd 8:0:0:0: [sdb] Assuming drive cache: write through [ 8967.851818] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.852365] sd 8:0:0:0: [sdb] Assuming drive cache: write through [ 8967.852370] sdb: sdb1 [ 8967.871315] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.871853] sd 8:0:0:0: [sdb] Assuming drive cache: write through [ 8967.871856] sd 8:0:0:0: [sdb] Attached SCSI disk [ 8967.950728] xhci_hcd 0000:02:00.0: WARN: Stalled endpoint [ 8967.951355] sd 8:0:0:0: [sdb] Sense Key : Recovered Error [current] [descriptor] [ 8967.951361] Descriptor sense data with sense descriptors (in hex): [ 8967.951363] 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00 [ 8967.951375] 00 00 00 00 00 50 [ 8967.951380] sd 8:0:0:0: [sdb] ASC=0x4 ASCQ=0x1d [ 8968.790076] xhci_hcd 0000:02:00.0: HC died; cleaning up [ 8968.790076] usb 6-3: USB disconnect, address 2 [ 8999.008554] scsi 8:0:0:0: [sdb] Unhandled error code [ 8999.008558] scsi 8:0:0:0: [sdb] Result: hostbyte=DID_TIME_OUT driverbyte=DRIVER_OK [ 8999.008562] scsi 8:0:0:0: [sdb] CDB: Read(10): 28 00 74 70 97 39 00 00 3e 00 [ 8999.008573] end_request: I/O error, dev sdb, sector 1953535801 [ 8999.008578] Buffer I/O error on device sdb1, logical block 1953535738 [ 8999.008582] Buffer I/O error on device sdb1, logical block 1953535739 [ 8999.008585] Buffer I/O error on device sdb1, logical block 1953535740 [ 8999.008589] Buffer I/O error on device sdb1, logical block 1953535741 [ 8999.008592] Buffer I/O error on device sdb1, logical block 1953535742 [ 8999.008595] Buffer I/O error on device sdb1, logical block 1953535743 [ 8999.008600] Buffer I/O error on device sdb1, logical block 1953535744 [ 8999.008603] Buffer I/O error on device sdb1, logical block 1953535745 [ 8999.008606] Buffer I/O error on device sdb1, logical block 1953535746 [ 8999.008609] Buffer I/O error on device sdb1, logical block 1953535747 [ 8999.008642] scsi 8:0:0:0: rejecting I/O to offline device [ 8999.008747] scsi 8:0:0:0: [sdb] Unhandled error code [ 8999.008749] scsi 8:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 8999.008752] scsi 8:0:0:0: [sdb] CDB: Read(10): 28 00 74 70 97 77 00 00 3e 00 [ 8999.008760] end_request: I/O error, dev sdb, sector 1953535863 sudo lspci -v 2:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Physical Slot: 32 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fe9fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd If I try to put into this controller any USB 2.0, it works fine. But USB 3.0 nope. Any idea?

  Read the article

• World Record Performance on PeopleSoft Enterprise Financials Benchmark on SPARC T4-2

  - by Brian

  Oracle's SPARC T4-2 server achieved World Record performance on Oracle's PeopleSoft Enterprise Financials 9.1 executing 20 Million Journals lines in 8.92 minutes on Oracle Database 11g Release 2 running on Oracle Solaris 11. This is the first result published on this version of the benchmark. The SPARC T4-2 server was able to process 20 million general ledger journal edit and post batch jobs in 8.92 minutes on this benchmark that reflects a large customer environment that utilizes a back-end database of nearly 500 GB. This benchmark demonstrates that the SPARC T4-2 server with PeopleSoft Financials 9.1 can easily process 100 million journal lines in less than 1 hour. The SPARC T4-2 server delivered more than 146 MB/sec of IO throughput with Oracle Database 11g running on Oracle Solaris 11. Performance Landscape Results are presented for PeopleSoft Financials Benchmark 9.1. Results obtained with PeopleSoft Financials Benchmark 9.1 are not comparable to the the previous version of the benchmark, PeopleSoft Financials Benchmark 9.0, due to significant change in data model and supports only batch. PeopleSoft Financials Benchmark, Version 9.1 Solution Under Test Batch (min) SPARC T4-2 (2 x SPARC T4, 2.85 GHz) 8.92 Results from PeopleSoft Financials Benchmark 9.0. PeopleSoft Financials Benchmark, Version 9.0 Solution Under Test Batch (min) Batch with Online (min) SPARC Enterprise M4000 (Web/App) SPARC Enterprise M5000 (DB) 33.09 34.72 SPARC T3-1 (Web/App) SPARC Enterprise M5000 (DB) 35.82 37.01 Configuration Summary Hardware Configuration: 1 x SPARC T4-2 server 2 x SPARC T4 processors, 2.85 GHz 128 GB memory Storage Configuration: 1 x Sun Storage F5100 Flash Array (for database and redo logs) 2 x Sun Storage 2540-M2 arrays and 2 x Sun Storage 2501-M2 arrays (for backup) Software Configuration: Oracle Solaris 11 11/11 SRU 7.5 Oracle Database 11g Release 2 (11.2.0.3) PeopleSoft Financials 9.1 Feature Pack 2 PeopleSoft Supply Chain Management 9.1 Feature Pack 2 PeopleSoft PeopleTools 8.52 latest patch - 8.52.03 Oracle WebLogic Server 10.3.5 Java Platform, Standard Edition Development Kit 6 Update 32 Benchmark Description The PeopleSoft Enterprise Financials 9.1 benchmark emulates a large enterprise that processes and validates a large number of financial journal transactions before posting the journal entry to the ledger. The validation process certifies that the journal entries are accurate, ensuring that ChartFields values are valid, debits and credits equal out, and inter/intra-units are balanced. Once validated, the entries are processed, ensuring that each journal line posts to the correct target ledger, and then changes the journal status to posted. In this benchmark, the Journal Edit & Post is set up to edit and post both Inter-Unit and Regular multi-currency journals. The benchmark processes 20 million journal lines using AppEngine for edits and Cobol for post processes. See Also Oracle PeopleSoft Benchmark White Papers oracle.com SPARC T4-2 Server oracle.com OTN PeopleSoft Financial Management oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 Enterprise Edition oracle.com OTN Disclosure Statement Copyright 2012, Oracle and/or its affiliates. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Results as of 1 October 2012.

  Read the article

• Not Dead, Just Busy

  - by MOSSLover

  So I didn’t die in a freak smelting accident yet, but I have been dealing with a lot of different things.  I had to take a bit of a break to deal with the cat death issue.  I am not fully recovered, because well it just happened a few months ago.  It kind of sucked.  Plus the apartment feels a lot bigger. Then you have the whole New York Comic Con thing where I had to plan some cosplay costumes.  I have been trying to find time to hang out with friends and have a social life.  That plus I built an entire presentation for iOS development for New York Code Camp.  I am also planning a couple MS Community dinners (namely one a week from Tuesday) plus a give camp.  I am also planning a vacation around SPS UK plus I will be at SPC.  Life is just incredibly hectic and when you factor in dating to the mix it’s gotten insane to the point where some day I just have to go dark.  Hence the lack of blogging.  I am just trying to keep up with everything and everyone without losing myself. If you guys will be at SPC or SPS UK I will be at both places this year.  Stop by the Planet Technologies booth and see me or I’ll be around somewhere.  I am really sorry if I don’t remember you from an event or if you are someone following me on twitter.  I am trying to get better at the mnemonic memory devices, but I think things broke down around the 47th event I attended or spoke at or something to that nature.  If anyone wants to talk to Cathy, Lori, or I about Women in SharePoint definitely find us at the event.  Anyway good night and good luck guys.  I promise to check back at least once before the year ends.  In the meantime twitter stalking is always possible.  Sometimes I even respond back. Technorati Tags: SPC,SPS UK,NYCC,NYC Code Camp,MOSSLover

  Read the article

• Invitation: Oracle EMEA Analytics & Data Integration Partner Forum, 12th November 2012, London (UK)

  - by rituchhibber

  Oracle PartnerNetwork | Account | Feedback INVITATIONORACLE EMEA ANALYTICS & DATA INTEGRATION PARTNER FORUM MONDAY 12TH NOVEMBER, 2012 IN LONDON (UK) Dear partner Come to hear the latest news from Oracle OpenWorld about Oracle BI & Data Integration, and propel your business growth as an Oracle partner. This event should appeal to BI or Data Integration specialised partners, Executives, Sales, Pre-sales and Solution architects: with a choice of participation in the plenary day and then a set of special interest (technical) sessions. The follow on breakout sessions from the 13th November provide deeper dives and technical training for those of you who wish to stay for more detailed and hands-on workshops.Keynote: Andrew Sutherland, SVP Oracle Technology. Data Integration can bring great value to your customers by moving data to transform their business experiences in Oracle pan-EMEA Data Integration business development and opportunities for partners. Hot agenda items will include: The Fusion Middleware Stack: Engineered to work together A complete Analytics and Data Integration Solution Architecture: Big Data and Little Data combined In-Memory Analytics for Extreme Insight Latest Product Development roadmap for Data Integration and Analytics Venue: Oracles London CITY Moorgate OfficesDuring this event you can learn about partner success stories, participate in an array of break-out sessions, exchange information with other partners and enjoy a vibrant panel discussion. Places are limited, Register your seat today! To register to this event CLICK HERE Note: Registration for the conference and the deeper dives and technical training is free of charge to OPN member Partners, but you will be responsible for your own travel and hotel expenses. Event Schedule November 12th:Day 1 Main Plenary Session : Full day, starting 10.30 am.Oracle Hosted Dinner in the Evening November 13th:onwards Architecture Masterclass : IM Reference Architecture – Big Data and Little Data combined(1 day) BI-Apps Bootcamp(4-days) Oracle Data Integrator and Oracle Enterprise Data Quality workshop(1-day) Golden Gate Workshop(1-day) For further information and detail download the Agenda (pdf) or contact Michael Hallett at [email protected] look forward to seeing you in there. Best regards, Mike HallettAlliances and Channels DirectorBI & EPM Oracle EMEAM.No: +44 7831 276 989 [email protected] Duncan HarveyBusiness Development Directorfor Data IntegrationM.No: +420 608 283 [email protected] Milomir VojvodicBusiness Development Manager for Data IntegrationM.No: +420 608 283 [email protected] Copyright © 2012, Oracle and/or its affiliates. All rights reserved. Contact PBC | Legal Notices and Terms of Use | Privacy

  Read the article

• Why does my MySQL remote-connection fail (VLAN)?

  - by Johannes Nielsen

  ubuntu-community! Again I have a problem with my special friend MySQL :D I have got two servers - a database-server and a web-server - who are connected via VLAN. Now I want the web-server to have remote access to the database-server's MySQL. So I created the user user in mysql.user. user's Host is xxx.yyy.zzz.9 which is the internal IP-address of the web-server. xxx.yyy.zzz.0 is the network. I also created user with Host % . As long as I use MySQL on the database-server logging in as user, everything works fine. But trying to log in as user from xxx.yyy.zzz.9 using mysql -h xxx.yyy.zzz.8 -u user -p (where xxx.yyy.zzz.8 is the database-server's internal IP), I get ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.yyy.zzz.8' (110) So I tried to activate Bind-Address in the my.cnf file. Well, if I use xxx.yyy.zzz.8, nothing changes. But if I try xxx.yyy.zzz.9 and try to restart MySQL, I get mysql stop/waiting start: Job failed to start I checked the log files and found - nothing. The database-server's MySQL doesn't even register, that the web-server tries to connect remotely. My idea is, that maybe I didn't configure the VLAN properley, even though I asked someone who actually knows such stuff and he told me, I did everything right. What I wrote into /etc/networking/interfaces is: #The VLAN auto eth1 iface eth1 inet static address xxx.yyy.zzz..8 netmask 255.255.255.0 network xxx.yyy.zzz.0 broadcast xxx.yyy.zzz.255 mtu 1500 ifconfig returns eth1 Link encap:Ethernet HWaddr xxxxxxxxxxxxxx inet addr:xxx.yyy.zzz.8 Bcast:xxx.yyy.zzz.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxxxxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:241146 errors:0 dropped:0 overruns:0 frame:0 TX packets:9765 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17825995 (17.8 MB) TX bytes:566602 (566.6 KB) Memory:fb900000-fb920000 for the eth1, what is, what I configured. (This is for the database-server, the web-server looks similar). ethtool eth1 returns: Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000003 (3) drv probe Link detected: yes (This is for the database-server, the web-server looks similar). Actually I think, everything is right, but it still doesn't work. Is there someone with an idea? EDIT: I commented ou Bind-Address in my.cnf after it didn't work.

  Read the article

• Microsoft MVP Award Nomination

  - by Mark A. Wilson

  I am extremely honored to announce that I have been nominated to receive the Microsoft MVP Award for my contributions in C#! Hold on; I have not won the award yet. But to be nominated is really humbling. Thank you very much! For those of you who may not know, here is a high-level summary of the MVP award: The Microsoft Most Valuable Professional (MVP) Program recognizes and thanks outstanding members of technical communities for their community participation and willingness to help others. The program celebrates the most active community members from around the world who provide invaluable online and offline expertise that enriches the community experience and makes a difference in technical communities featuring Microsoft products. MVPs are credible, technology experts from around the world who inspire others to learn and grow through active technical community participation. While MVPs come from many backgrounds and a wide range of technical communities, they share a passion for technology and a demonstrated willingness to help others. MVPs do this through the books and articles they author, the Web sites they manage, the blogs they maintain, the user groups they participate in, the chats they host or contribute to, the events and training sessions where they present, as well as through the questions they answer in technical newsgroups or message boards. - Microsoft MVP Award Nomination Email I guess I should start my nomination acceptance speech by profusely thanking Microsoft as well as everyone who nominated me. Unfortunately, I’m not completely certain who those people are. While I could guess (in no particular order: Bill J., Brian H., Glen G., and/or Rob Z.), I would much rather update this post accordingly after I know for certain who to properly thank. I certainly don’t want to leave anyone out! Please Help My next task is to provide the MVP Award committee with information and descriptions of my contributions during the past 12 months. For someone who has difficulty remembering what they did just last week, trying to remember something that I did 12 months ago is going to be a real challenge. (Yes, I should do a better job blogging about my activities. I’m just so busy!) Since this is an award about community, I invite and encourage you to participate. Please leave a comment below or send me an email. Help jog my memory by listing anything and everything that you can think of that would apply and/or be important to include in my reply back to the committee. I welcome advice on what to say and how to say it from previous award winners. Again, I greatly appreciate the nomination and welcome any assistance you can provide. Thanks for visiting and till next time, Mark A. Wilson      Mark's Geekswithblogs Blog Enterprise Developers Guild Technorati Tags: Community,Way Off Topic

  Read the article

< Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >