Search Results

Search found 14435 results on 578 pages for 'disk usage'.

Page 404/578 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

• Backup SQL server db issue: delete old backup files

  - by David.Chu.ca

  I tried to use sqlmaint.exe tool to back up a database on a remote PC. Here is an example of backup: sqlmaint.exe -S remoteSQLServer\SQLInstance -U username -P pwdxxx -D myDB -BkUpMedia DISK -BkUpDB C:\MSSQL_Backups -DelBkUps 3days ... Here I specified to delete backups older than 3 days. However, the job seems not deleting old bak files on the remote PC(where the SQL server sits). The remote PC has Windows 2008 Server. I also set the C:\MSQL_Backups as shared network drive for EnyOne as owner. My understanding is that the job will delete any bak files older than 3 days. Not sure what I missed? By the way, the job runs at a box with SQL server 2005 installed.

  Read the article

• Configuring BitLocker on existing Windows Server 2008

  - by neildeadman

  On our file server, we want to enable BitLocker so that we can encrypt a single drive and I know that we have to also encrypt the drive the system is installed on. In my tests with VMs, I have to create a partition on the same disk as Windows is installed either before I install Windows or after (I can use the BitLocker Drive Preparation Tool). This tool shrinks the C: drive to make way for a 1.5GB partition. I'm a little concerned about doing this with a live system so wanted to see if it was possible to get BitLocker to use a partition on another drive?

  Read the article

• How can I improve performance over SMB/CIFS for an application that has poor write speeds?

  - by Jeremy

  I have a third party application that reads several large files and generates a third large file. Its performance is quite good when the generated file is stored on "local storage", i.e. either a direct attached or iSCSI-based disk. The source files that are read can be stored remotely on our NAS and accessed via SMB with little effect on performance. However, if we attempt to write the target file to any kind of SMB/CIFS share (Samba or Windows Server) the performance drops almost ten-fold. This is unacceptably slow in our case. Writing files to network shares is not otherwise slow. I can copy large files to SMB shares and get great performance - near what I would expect is possible given the disks and network in question. I have a theory that this application's problem with SMB shares has something to do with a lack of write caching over the share and perhaps lots of network roundtrips. Is this possible and is there anything that can be done about it?

  Read the article

• Dual boot Windows 8 and Ubuntu?

  - by askvictor

  I've installed Windows 8 on a machine (lenovo x220 laptop) with Ubuntu 12.10 already installed on another disk. I am guessing that Windows 8 has convinced the laptop to switch to UEFI boot (rather than the BIOS boot that was there previously) as the Lenovo splash screen on startup now no longer has the options to interrupt the boot process (e.g. to choose the boot drive). Previously I had Windows 8 on one drive and Ubuntu on the other drive, so could choose my OS through the BIOS rather than through grub or other bootloader but now no longer have that option. How can I get back the option to boot Ubuntu? I would sort of prefer UEFI boot as it seems much faster than BIOS.

  Read the article

• 4TB HGST SATA drive only shows 1.62 TB in Windows Server 2012

  - by user136085

  I'm using a Supermicro X9SRE-3F motherboard with the latest BIOS and 2x 4TB drives connected to the on-board SATA controller. If I set the BIOS to RAID and create a RAID 1 array, the array shows up in the BIOS as 3.6TB. However when I boot Windows (on a separate RAID 1 array), the 4TB drives show up individually in disk manager as 2x 1.62TB drives. I could use Windows 2012 to set up software RAID 1, but when I set the BIOS back to 2x individual drives, they still show up in Windows as 2x 1.62TB drives. How do I access the full capacity of these drives? Thanks, Brian Bulaw

  Read the article

• HDD bad sectors with OS

  - by Michael Z

  I wonder is that possible for OS to make bad sectors on Hard Drive? Preface: I have bought new HDD on 1Tb WB Caviar Black. I have installed new OS on ext4 partition Ubuntu 12.04.1 LTS. After few days S.M.A.R.T. of the Ubuntu's Disk Utility show that my hard has bad sectors! I have checked on S.M.A.R.T. immediately after installing OS - all was OK. During new OS working I have noticed some strange with HDD - all OS was freezed from 20 sec to 1 min and I have heard like HDD's engine restarting. At the dmes I have found something like this: [40085.407947] ata1.00: device reported invalid CHS sector 0

  Read the article

• Looking for a good Web Server that is cheap

  - by SoLoGHoST

  I am a Project Manager, and former Lead Developer for a software portal system that requires a forum software to run. I am in need of a server that is cheap, reliable, and supports the latest PHP (5.2+), MySQL, unlimited e-mails (preferably), a cPanel, multiple sub-domains (atleast 3+). Currently I am paying $34.95 USD/month (approx. $420 USD/year). This is too high for me to pay to keep the site running. I just recently became Project Manager and in charge of Finances and I'm extremely concerned for the future of Dream Portal. With those prices I'm not sure I'll be able to keep it running for too long. Can someone please tell me of a good server that meets all of the requirements that I listed above that is cheaper on a yearly basis? Note: Currently on a Dedicated Server with limited disk space at 15000 MB (15 GB), monthly bandwidth = 500000 MB, 50 emails limit, 20 sub-domains limit, 30 FTP accts., and 25 SQL Databases.

  Read the article

• Permissionless external drive with NTFS

  - by user12889

  I have an external hard disk which has 1 partition, formatted in NTFS. I use this drive on multiple computers with a different logins on different machines, Windows XP and Windows 7. All files are plain old files, not OS encrypted or compressed. Every now and then Windows 7 does not let me access some files, citing permission problems. I can circumvent this per case by taking ownership and setting appropriate permissions. This, however, is tedious. Is there a simple way to tell Windows to not enforce or store any permissions on any file/directory on a partition?

  Read the article

• How to mount remote sambe from local host with multiple groups ?

  - by Dragos

  I am using mount.cifs to mount a remote samba share (both client and server are Ubuntu server 8.04) like this: mount.cifs //sambaserver/samba /mountpath -o credentials=/path/.credentials,uid=someuser,gid=1000 `$ cat .credentials username=user password=password I mounted a user from local system with username and password with mount.cifs but the problem is that the user is part of multiple groups on the remote system and with mount.cifs I can only specify one gid. Is there a way to specify all the gids that the remote user has ? Is there a way to: 1) Mount the remote samba with multiple groups on the local system ? 2) Browse the mount from 1) with the terminal since I want to pass some files from samba as arguments to local programs. Other solutions would be: nautilus sftp:// which runs through gvfs but the newer gnome does not write to disk the ~/.gvfs anymore so I can't browse it in terminal. An the last solution would be nfs but that means that I have to synchronize the uids and gids on the local system with the ones from the server.

  Read the article

• How do I tell if my firewire connection is running as 400 or 800?

  - by Tom

  I have a MacBook Pro with FireWire 800 and a freecom external harddrive that has USB3, FireWire 400 and 800. I am using a Nikkai FireWire 800 cable that has 800 connector on one end and a 400 connector on the other end. The 800 connector is attached to the MacBook pro and the 400 connector is attached to the freecom drive. Is there any way to tell what connection has been established? I looked at disk utility and it simply said 'FireWire'. Is there a command-line tool that would give more information? If it's 400, I plan to swap the cable for 800 connector at both ends.

  Read the article

• Windows 7, Drivers, Cloning and Sysprep

  - by Frank Thornton

  I have Windows 7 working on one machine but when I move it off to the new machine it crashes. If this is a driver issue do I need to download the drivers and install them first? Or do I install Windows 7 on the new machine first then copy the drivers folder over to the other disk so it will boot up correctly? EDIT: I was trying this as well: http://www.todo-backup.com/support/tutorial/redeploy-system-to-dissimilar-hardware.htm EDIT: I tried sysprep but on bootup I see the Windows logo then the system crashes. I can stick the drive back in the old hardware and it runs fine.

  Read the article

• FreeDOS reinstallation -- accidental script change

  - by jerry2144

  I'm extremely new to FreeDOS and I got a new HP desktop computer with the FreeDOS operating system. I messed up and accidentally changed its scripts and messed around with it's boot order. Long story short, I'm getting a disk error when I boot up. I believe I need to just reinstall FreeDOS and all should be good, but I want to get someone's opinion with much more experience than my own. Also, if someone could guide me through the installation process using a DVD installer that would be amazing. I have already downloaded the FreeDOS iso image and unzipped it. I don't know what I need to do now though. Should I even have unzipped it?

  Read the article

• File corruption when copying different file on raid 1

  - by Stephan

  I have a RAID 1 configuration of 2 1TB drives on a Fedora 12 box. Most of what is stored there are video files that are numerical labeled. The problem I'm having is that I had one of the video files get corrupted. I copied a replacement from a backup and replaced the bad file and now it works fine. However, after doing this the next numbered file goes from 350MB to 200KB and all but about .5 second of video disappears. If I then replace that file it happens to the next one down the line. Ex: Replace corrupt file 1.avi and file 2.avi shrinks to 200KB. Replace now corrupted 2.avi and it works but 3.avi gets screwed up. I have run SMART tests on the drives and they report fine. Does anyone have any tests I can run to try to figure out what is going on? EDIT: It is a two disk software RAID 1 with an ext4 filesystem

  Read the article

• SFTP through proxy

  - by aerodynamic_props

  I have a large amount of data on scratch space at computer b that I want to get. In my network I cannot directly connect to computer b (ssh exits with "No route to host"); I must first connect to computer a, and then connect to computer b. I cannot move the data from the scratch space on computer b to computer a because of a disk quota that is imposed on me at computer a. How can I move the data from computer b to my computer in this situation?

  Read the article

• Problem reinstalling GRUB

  - by DisgruntledGoat

  I have a PC that dual-boots Ubuntu and Windows Vista. I recently reinstalled Windows Vista after some problems and now the bootloader's gone. I've been trying to follow this Ubuntu community guide but it's not working. I have Grub Legacy according to the first part (I installed Ubuntu 9.04 originally then upgraded). From the 9.04 LiveCD, I ran this: sudo grub-install --root-directory=/media/disk /dev/sda5 sda5 is the Ubuntu partition. I get this output: grub-probe: error: Cannot open `/boot/grub/device.map` [: 494: =: unexpected operator Installing GRUB to /dev/sda5 as (hd0,4)... Installation finished.No errors reported. This is the contents...(etc) (hd0) /dev/sda In the bit below, when I run setup (hd0) I get an error, "Error 17: Cannot mount selected partition" Little help?

  Read the article

• Is it possible to change the default scan folder on an Eye-Fi Wireless SD Card

  - by MichaelPh

  By default Eye-Fi cards scan the DCIM folder (and subfolders) used by most digital cameras for new images to upload. Is there a way of changing this to a different folder? In my particular case I'm using a Kodak photo scanner (P461) that uses a PHOTO(N) folder format to store the scanned images, as far as I know the device has no configuration interface to alter this setting so that doesn't seem to be an option. This topic on the Eye-Fi forums is the closest I've come to a solution, but a perfunctory investigation of Disk Probe doesn't make it obvious what needs to be modified on the card.

  Read the article

• Simplest way to shrink transaction log files on a mirrored production database

  - by MGOwen

  What's the simplest way to shrink transaction log file on a mirrored production database? I have to, as my disk space is running out. I will make a full database backup before I do this, so I don't need to keep anything from the transaction log (right? I have daily full database backup, probably never need point-in-time restore, though I'll keep the option open if I can - that's all the .ldf is really for, correct?). (Hope this isn't an exact duplicate, I read a lot of questions but couldn't find this exact scenario elsewhere).

  Read the article

• PC wont boot with more than 1 stick of RAM.

  - by Aidan

  Hi Guys, I've got the following computer and I've just put in a new CPU QX9650 and I've run into this problem since making this hardware change. Whenever I put more than 1 of my 4 sticks of ram into my machine it wont load an OS. It'll go through the BIOS but BSOD on windows load. It also wont let me install an OS from disk or boot into Linux. I've ran memtest with all 4 sticks in and I get 10k+ errors on test5. Each stick of ram on it's own is fine and functions properly. I only have problems when all 4 sticks are in the machine at the same time. System specs.. CPU: QX9650 Mobo: Asus P5B 2104 BIOS RAM: 2xPC25400 DDR2 , 2xPC2 6400 both OCZ. Is the problem on my end or is the CPU faulty?

  Read the article

• PC wont boot with more than 1 stick of RAM.

  - by Aidan

  Hi Guys, I've got the following computer and I've just put in a new CPU QX9650 and I've run into this problem since making this hardware change. Whenever I put more than 1 of my 4 sticks of ram into my machine it wont load an OS. It'll go through the BIOS but BSOD on windows load. It also wont let me install an OS from disk or boot into Linux. I've ran memtest with all 4 sticks in and I get 10k+ errors on test5. Each stick of ram on it's own is fine and functions properly. I only have problems when all 4 sticks are in the machine at the same time. System specs.. CPU: QX9650 Mobo: Asus P5B 2104 BIOS RAM: 2xPC25400 DDR2 , 2xPC2 6400 both OCZ. Is the problem on my end or is the CPU faulty?

  Read the article

• Ubuntu server: lost prompt on monitor

  - by Richard

  Hello All, I am running Ubuntu 9.04 server edition. I have a monitor plugged into the box for occasional admin tasks. I pulled out a USB disk (without unmounting) and the screen is now full with this message: Buffer I/O error on device sdc1, logical block 7778778 I can't seem to clear the screen or get a prompt back. Doesn't appear to be registering keyboard strokes. The box is still running fine (I can ssh in from elsewhere and evrything is running as normal). Any ideas on how to clear screen and get my prompt back?

  Read the article

• How to mount remote samba share from local host with multiple groups?

  - by Dragos

  I am using mount.cifs to mount a remote samba share (both client and server are Ubuntu server 8.04) like this: mount.cifs //sambaserver/samba /mountpath -o credentials=/path/.credentials,uid=someuser,gid=1000 $ cat .credentials username=user password=password I mounted a user from local system with username and password with mount.cifs but the problem is that the user is part of multiple groups on the remote system and with mount.cifs I can only specify one gid. Is there a way to specify all the gids that the remote user has? Is there a way to: Mount the remote samba with multiple groups on the local system? Browse the mount from 1) with the terminal since I want to pass some files from samba as arguments to local programs. Other solutions would be: nautilus sftp:// which runs through gvfs; but the newer gnome does not write to disk the ~/.gvfs anymore so I can't browse it in terminal. And the last solution would be NFS but that means that I have to synchronize the uids and gids on the local system with the ones from the server.

  Read the article

• Adaptec 2020SA RAID controller Set up in RAID5, one drive went down, can I still get data?

  - by SJaguar13

  I have 6 1tb drives in a RAID5. 1 drive went down. On the RAID was 2 virtual machines that I really need back up and running. The spare drive I have to put in the server is a 1.5tb drive, which exceeds the physical per drive limit of the 2020SA. The drive is found in the disk utility, but it is not found in the array management section. I cannot add the drive to the array to have it rebuild. I have a replacement drive along with some spares on their way from Newegg, but I am still looking at a few days of downtime. Is it possible to use the 5 working drives to get the VMs copied off and on to another server or do I just have to wait for the drives to get here?

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >