Search Results

Search found 2646 results on 106 pages for '300 baud'.

Page 41/106 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

• Can't connect to domain computers until reboot

  - by thealliedhacker

  I have a domain with about 300 Windows 7 and XP machines, with the domain controllers running Server 2003. Sometimes, I lose the ability to communicate/authenticate with some of the machines until I reboot my computer. This also happens from other computers and regardless of user account and operating system. In other words, say I'm on ComputerA, and I can't connect to ComputerX. I can go to ComputerB and connect to ComputerX, but ComputerB may not be able to connect to ComputerY. If you reboot ComputerA, then it will be able to connect to ComputerX again. Here are some messages from various utilities: sc: [SC] OpenSCManager FAILED 1722: The RPC server is unavailable. mmc (compmgmt.msc): Computer (computer name) cannot be managed. The network path was not found. explorer (\\computer): Windows cannot access \\(computer name). ping: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss) / Average = 1ms

  Read the article

• nagios wrongly reports packet loss

  - by Alien Life Form

  Lately, on my nagios 3.2.3 install (CentOS5, monitoring ~ 300 hosts, 1150 services) has sdtarted to occasionally report high packet loss on 50-60 hosts at a time. Problem is it's bogus. Manual runs of ping (or its own check_ping binary) finds no fault with any of the affected hosts. The only possible cures I found so far are: run all the checks manually (they will succeed but it may act up again on next check) acknowledge and wait for the problem to go away (may take several ours) I suspect (but have no particular reason other than single rescheduled checks succeeding) that the problem may lay with all the checks being mass scheduled together - in which case introducing some jitter in the scheduling (how?) might help. Or it may be something completely different. Ideas, anyone?

  Read the article

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• Can't bring NAT to work

  - by user31738

  Hello, I bought a D-link DIR-300 wireless router and i can't bring NAT to work, i have an ssh and http service i need to forward to the internet. My connection is as follows: I have an ADSL connection, i'm using a ADSL ethernet modem connected and working, it doesnt let me put it on bridge mode. I have my router connected to my adsl modem through ethernet, it gets its ip through DHCP (and i'ts always the same) I have a desktop computer running linux with apache and openssh configured and working, it has fixed ip. I configured the NAT in the modem forwarding port 22 from the router ip to the internet. In the router i setup NAT forwarding port 22 from the desktop computer fixed ip to out there. This setup already worked with a fonera i had before, can anyone help me with this or tell me what kind of tests do i need to do? How can i test if the router is forwarding ports correctly before the modem?

  Read the article

• CentOS openLDAP cert trust issues

  - by 84104

  # LDAPTLS_CACERTDIR=/etc/ssl/certs/ ldapwhoami -x -ZZ -H ldaps://ldap.domain.tld ldap_start_tls: Can't contact LDAP server (-1) additional info: TLS error -8172:Peer's certificate issuer has been marked as not trusted by the user. # openssl s_client -connect ldap.domain.tld:636 -CApath /etc/ssl/certs <... successful tls negotiation stuff ...> Compression: 1 (zlib compression) Start Time: 1349994779 Timeout : 300 (sec) Verify return code: 0 (ok) --- openssl seems to think the certificate is fine, but openldap's libraries (pam_ldap exhibits similar behavior, which is how I got on to this mess) disagree. What am I doing wrong?

  Read the article

• AWS Elastic load balancer doesn't decrease instances from Alarm Trigger

  - by jchysk

  I have a load balancer that I created an auto-scaling-group and launch-config for. I created the auto-scaling-group with a min-size of 1 and max size of 20. I have a scaledown policy: as-put-scaling-policy SBMScaleDownPolicy --auto-scaling-group SBMAutoScaleGroup --adjustment=-1 --type ChangeInCapacity --cooldown 300 Then I set up an alarm: mon-put-metric-alarm SBMLowCPUAlarm --comparison-operator LessThanThreshold --evaluation-periods 1 --metric-name CPUUtilization --namespace "AWS/EC2" --period 600 --statistic Average --threshold 35 --alarm-actions arn:aws:autoscaling:us-east-1:policystuffhere:autoScalingGroupName/SBMAutoScaleGroup:policyName/SBMScaleDownPolicy --dimensions "AutoScalingGroupName=SBMAutoScaleGroup" When average CPU usage over 10 minutes is under 35, in CloudFront the alarm shows up as "In Alarm State" but doesn't decrease the number of instances. Also, if there's only one instance running it'll spin up another to 2 even if a scale up alarm isn't hit. It seems like the default value is just set to 2 somehow. How can I change this?

  Read the article

• How to generate a 8 bit per sample wav audio file in VLC

  - by Ahmed safan

  I'm using the following vlc command line to extract first 5 minutes of audio from video file "-I dummy -vvv --no-sout-video --sout-audio --no-sout-rtp-sap --no-sout-standard-sap --ttl=1 --sout-transcode-threads=5 --sout-transcode-high-priority --sout-keep --sout #transcode{acodec=s16l,channels=1,samplerate=8000,ab=64}:std{mux=wav,access=file,dst="c:\dest.wav"} "c:\originalvideo.mpg" --start-time=0 --stop-time=300 vlc://quit"; if ab=64 =64 k bits per second and samples per second=8 k samples then bits per sample=64/8=8 bits per sample but the problem is that the output file always has samples of 16 bits per sample. I know that sample can contain bits from 8 , 16, 24 to 32 bits per sample. i want to get 8 bits per sample file how can this be done ?

  Read the article

• MySQL too many connections

  - by Webnet

  On my server I have 7 databases. Our server has 512 MB of RAM which I'm getting upgraded this evening to 2GB and has a 2.4 single processor. I've gotten an error about the connection limit exceeded. With increasing my RAM, is it ok to increase the number of connections? Currently it's set to 200 but a single page may connect to 3-4 databases considering JOINs and things. We've setup so many databases for mere organization. We have a total of about 250-300 tables in all of the databases. Any advice would be appreciated :)

  Read the article

• Server 2008 R2 - Boot disk RAID 1 - migrate to larger disk

  - by William Hooper

  My group inherited several 2008 R2 servers with single 70GB RAID 1 boot/system disks. No other disks in the servers. We need larger boot / system disk. Plan is : to replace one disk with new 500 GB drive wait for resync replace other smaller disk with 2nd 500 GB drive wait for resysnc Now I should have 500 GB RAID 1 with original 70 GB partition Then I would like to extend the 70 GB partition to 200 GB and add D: drive partition with remaining 300 GB Can the above be done using Windows Disk Management and / or Windows DiskPart ?

  Read the article

• need help writing puppet module for sssd.conf using Hiera

  - by mr.zog

  I need to build a module to manage /etc/sssd/sssd.conf on our Red Hat VMs. The sssd modules published on the forge don't seem to do what I want, nor do I feel like forking any of them. I want to keep all the configuration data in Hiera's common.yaml file. Below is my sssd.conf file. [sssd] config_file_version = 2 services = nss, pam domains = default [nss] filter_groups = root filter_users = root reconnection_retries = 3 entry_cache_timeout = 300 entry_cache_nowait_percentage = 75 [pam] [domain/default] auth_provider = ldap ldap_id_use_start_tls = True chpass_provider = ldap cache_credentials = True ldap_search_base = dc=ederp,dc=com id_provider = ldap ldap_uri = ldaps://lvldap1.lvs01.ederp.com/ ldaps://lvldap2.lvs01.ederp.com/ ldap_tls_cacertdir = /etc/openldap/cacerts What is the best, most economical way to build the sssd.conf file? Should I have multiple .pp files such as domain.pp, pam.pp etc. or should all the lines of configuration land in init.pp?

  Read the article

• Network monitoring solution

  - by Hellfrost

  Hello Serverfault ! I have a big distributed system I need to monitor. Background: My system is comprised of two servers, concentrating and controlling the system. Each server is connected to a set of devices (some custom kind of RF controllers, doesnt matter to my question), each device connects to a network switch, and eventually all devices talk to the servers, the protocol between the servers and the devices is UDP, usually the packets are very small, but there are really a LOT of packets. the network is also somewhat complex, and is deployed on a large area physically. i'll have 150-300 of these devices, each generating up to 100+ packets per second, and several network switches, perhaps on 2 different subnets. Question I'm looking for some solution that will allow me to monitor all this mess, how many packets are sent, where, how do they move through the network, bandwidth utilization, throughput, stuff like that. what would you recommend to achieve this? BTW Playing nice with windows is a requirement.

  Read the article

• Munin "Available entropy" when using address space layout randomization

  - by clawspoon

  Having just configured munin for statistics logging on my gentoo server (hardened profile), I am noticing that my "Available entropy" is consitently in the 200-300 range. This seems way to low, so I checked it manually using the command $ cat /proc/sys/kernel/random/entropy_avail 3544 Odd. Consistently very low values in Munin and practically filled up when checking manually. After thinking about the problem for a while I came to the conclusion that the problem is probably that I'm using Adress Space Layout Randomization which is using the entropy when running commands/programs. Since Munin runs a whole slew of programs all the entropy is used up, and Munin then measures how much entropy there is, resulting in the low values. Does anyone have any experience with this? How can this be avoided?

  Read the article

• Can't find second partition on encrypted drive with two partitions

  - by Thomas Uhrig

  I have a drive with two partitions, a system partition (Windows 7) and a partition just for data. Both are encrypted with the same password. I didn't had any problems, but yesterday my laptop gets broken. Now, I'm trying to connect the drive via USB to a new laptop and read it. The problem is, that I only see the system partition, not the one with my data. When I click on "Select Device", I can see my drive as "Harddisk 1" with 300 gb. But I only see a single partition "Partition1" with 117 gb. I'm unable to find the second one. It's not a hidden partition. Any ideas? Thanks.

  Read the article

• How much memory should my rails stack be consuming?

  - by Hamish

  I am running my own webserver on a 384MB VPS from Slicehost to serve two Ruby on Rails applications on separate Virtual Hosts. I am running Phusion Passenger with Apache2. The following is the contents of my Passenger.conf <IfModule passenger_module> PassengerRoot /opt/ruby-enterprise-1.8.6-20090610/lib/ruby/gems/1.8/gems/passenger-2.2.11 PassengerLogLevel 0 PassengerRuby /usr/local/bin/ruby PassengerUserSwitching on PassengerDefaultUser nobody PassengerMaxPoolSize 3 PassengerMaxInstancesPerApp 2 PassengerPoolIdleTime 300 # Ruby on Rails Options RailsAutoDetect on RailsSpawnMethod smart NameVirtualHost *:80 If i do a 'top' on my server I have 314MB used on average, this seems like too much? Am I mistaken and if not what possible steps can I take to reduce the Memory usage? Thanks!

  Read the article

• IIS 6 on x64 and long URLs

  - by mausch

  I have a very long URL on a site hosted on Windows 2003 x64 that looks like this: http://myhost/a_very_very_long_url_around_300_chars_long (i.e. a single, very long segment around 300 chars long) Problem is, I'm getting a 400 Bad Request response from HTTP.SYS (it doesn't even reach IIS). I can tell because these requests show up in system32\LogFiles\HTTPERR, e.g: 2009-09-17 19:51:29 200.123.179.9 3636 192.168.129.50 80 HTTP/1.1 GET /a_very_very_long_url_around_300_chars_long 400 - URL - I tried setting UrlSegmentMaxLength in the registry and this fixes the issue on my Windows 2003 x86 box but not on the x64 production server. I tried this on another Win2k3 x64 server and it also failed. Any hints?

  Read the article

• What would be better in my case - apache, nginx or lighttpd ?

  - by The Devil

  Hey everybody, I'm writing a php site that's expected to get about 200-300 concurrent users browsing it. When initializing the application will load about 30 php classes, some 10 maybe 15 images and a couple of css files. So my question is what else can I do (except optimizing my code and using apc/eaccelerator for php) to get as close as possible to those numbers of concurrent users ? Currently we haven't chosen a server for the site to be hosted on but most probably it'll be a VPS Dual core + 2 or maybe 4gb ram. Is it possible for such a server to handle that load ? Also how could I test it myself and be sure that it'll be able to handle it ? Thanks in advance, Me

  Read the article

• Create Word files from Excel content

  - by Lennart

  I have an Excel file that I want to split into several files (Word, PDF is also good), based on content. The content is somewhat like this: Person Fase Date Item Text A 1 01-01-2012 Z Lorem ipsum A 2 01-02-2012 X Lorem ipsum B 1 02-01-2012 Y Lorem ipsum C 2 01-01-2012 Z Lorem ipsum I want Word/PDF documents with names like Person_Fase.docx And as content the date, item and text. Idealy in a table layout. Any hints/ clues on how to get there? It's about 700 clients, with up to 300 Excel entries each.

  Read the article

• Why does iChat Server keep connecting to proxy.eu.jabber.org?

  - by Tom Hamming

  I have OS X Server 10.6.5 running on a new Mac Mini (server model), serving several functions among which is iChat Server (iChat and Pidgin on Windows as clients). In the iChat log in Server Admin, I kept seeing entries about connecting to proxy.eu.jabber.org. It's for our office network and I wasn't excited about external access to it, so I disabled server-to-server XMPP federation and now the connections just time out. But why is it doing that in the first place? Sample log entry: (datetime) (servername)jabberd/resolver[portnum]: [xmpp-server._tcp.proxy.eu.jabber.org resolved to 208.68.163.220:5269 (300 seconds to live) then: sending dialback auth request for route '(full server hostname)/proxy.eu.jabber.org' A couple minutes later, it comes back with: dialback for outgoing route '(full server hostname)/proxy.eu.jabber.org' timed out

  Read the article

• What are performance limits of a database?

  - by Tommy

  What are some rough performance limits (read/s, write/s) for a single database server (no master-slave architecture), assuming storage on disk? How many read/s, write/s, depending on the kind of disk? (SSD vs non-SSD) , assuming simple operations (select one row by primary key, update one row, correctly indexed). I assume this limit is dependent on disk seek/write. EDIT: My question is more about getting rough metrics of the number of operations a database supports: to be able to know for example, if a new feature triggering 300 inserts/s can be supported without scaling out with additional servers.

  Read the article

• How much the distance and ms can affect on the download speed ?

  - by Prix

  Let's consider A (client) and B (server) where A makes download from B. How much can a bad routing from A to B affect the download speed ? For example A does a tracert to B and get a response of 10 steps where the avg ms is around 300 with 10% packet loss at the 4 step and when the connection is normal the avg from A to B is 10 ~ 30 ms. Could this sort of impact reduce A download speed drasticaly or as long as both side and routes have enough link for the full speed of A from B and vice-versa it should maintain the same speed ? Besides tracert and the ping analyse of A to B what else is used to identify the problem ? If you need extra information please let me know.

  Read the article

• Why does iChat Server keep connecting to proxy.eu.jabber.org?

  - by Tom Hamming

  I have OS X Server 10.6.5 running on a new Mac Mini (server model), serving several functions among which is iChat Server (iChat and Pidgin on Windows as clients). In the iChat log in Server Admin, I kept seeing entries about connecting to proxy.eu.jabber.org. It's for our office network and I wasn't excited about external access to it, so I disabled server-to-server XMPP federation and now the connections just time out. But why is it doing that in the first place? Sample log entry: (datetime) (servername)jabberd/resolver[portnum]: [xmpp-server._tcp.proxy.eu.jabber.org resolved to 208.68.163.220:5269 (300 seconds to live) then: sending dialback auth request for route '(full server hostname)/proxy.eu.jabber.org' A couple minutes later, it comes back with: dialback for outgoing route '(full server hostname)/proxy.eu.jabber.org' timed out

  Read the article

• HP DL370 G6 expansion

  - by user72185

  Hi, we are running a HP DL370 server with 6 x 300 gb disks on RAID 5. Due to a Windows update causing our server to fail recently, we couldn't access the data. I now want to separate the data from the OS (Windows server 2008 r2) so that if anything like that happens again, we can route everyone through a separate server. I have seen these HP storageworks enclosures (msa70) and have a couple of questions: Can I just take out our 2.5 inch 10k SAS drives, install them in the new Storageworks NAS and hey presto we would be up and running? If I wanted to then add another drive (I think there are 25 bays), can I just insert a blank but identical drive and the RAID 5 would dynamically expand to incorporate the new drive. Many thanks Adrian

  Read the article

• Can I increase the link speed of the RAS Server on our MS Win2k3 box?

  - by Ducain

  We are running a Win2K3 Server box, and I'm a remote employee that connects via VPN. I've been frustrated for some time by the connection speed over the VPN (the office HQ has a decent speed and I have a biz class connection here), and decided to do some checking today. This morning, I was dialed in and looked at the networking tab of the task manager, and I see that the adapter for the RAS Server (the box has 4 Gigabit adapters) has a speed that seems far too low. The speed for the RAS Server link hovers between 300 - 600 Kbps. The local connection (and others) all say 1 Gbps. Can I set this to a higher speed? Is this information accurate? Thanks for the input.

  Read the article

• Macbook Pro 15-inch replacement battery.

  - by ricbax

  So I've finally got to the 300+ cycles with my MBP 2008's original battery. Apple is pretty much "on the money" too! I am at 79% Health and getting the Condition: Replace Soon warning. So I went out to the closest Apple Store and bought a replacement. I would like to get the same lifespan out of my replacement if possible. My question is: The battery comes with a 2 dot (green) charge on the indicator, should I put the battery in and let it run down and do a full recharge OR begin charging it immediately and then let it run all the way to empty and recharge?

  Read the article

• ata error: UnrecovData Handshk

  - by Aaron Digulla

  I just saw this message in my log (openSUSE 11.3, Linux 2.6.36.2): ata6.00: exception Emask 0x10 SAct 0x1 SErr 0x400100 action 0x6 frozen ata6.00: irq_stat 0x08000000, interface fatal error ata6: SError: { UnrecovData Handshk } ata6.00: failed command: WRITE FPDMA QUEUED ata6.00: cmd 61/58:00:9f:69:00/00:00:00:00:00/40 tag 0 ncq 45056 out res 40/00:04:9f:69:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) ata6.00: status: { DRDY } ata6: hard resetting link ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: configured for UDMA/133 ata6: EH complete Two questions: Which disk caused the error? I search /sys and /proc but couldn't find a way to map ata6 to a device (/dev/sdaXY) When such an error happens, does Linux retry the disk operation? Or do I have a corrupt filesystem?

  Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >