Search Results

Search found 1014 results on 41 pages for 'collision'.

Page 41/41 | < Previous Page | 37 38 39 40 41 

• Elfsign Object Signing on Solaris

  - by danx

  Elfsign Object Signing on Solaris Don't let this happen to you—use elfsign! Solaris elfsign(1) is a command that signs and verifies ELF format executables. That includes not just executable programs (such as ls or cp), but other ELF format files including libraries (such as libnvpair.so) and kernel modules (such as autofs). Elfsign has been available since Solaris 10 and ELF format files distributed with Solaris, since Solaris 10, are signed by either Sun Microsystems or its successor, Oracle Corporation. When an ELF file is signed, elfsign adds a new section the ELF file, .SUNW_signature, that contains a RSA public key signature and other information about the signer. That is, the algorithm used, algorithm OID, signer CN/OU, and time stamp. The signature section can later be verified by elfsign or other software by matching the signature in the file agains the ELF file contents (excluding the signature). ELF executable files may also be signed by a 3rd-party or by the customer. This is useful for verifying the origin and authenticity of executable files installed on a system. The 3rd-party or customer public key certificate should be installed in /etc/certs/ to allow verification by elfsign. For currently-released versions of Solaris, only cryptographic framework plugin libraries are verified by Solaris. However, all ELF files may be verified by the elfsign command at any time. Elfsign Algorithms Elfsign signatures are created by taking a digest of the ELF section contents, then signing the digest with RSA. To verify, one takes a digest of ELF file and compares with the expected digest that's computed from the signature and RSA public key. Originally elfsign took a MD5 digest of a SHA-1 digest of the ELF file sections, then signed the resulting digest with RSA. In Solaris 11.1 then Solaris 11.1 SRU 7 (5/2013), the elfsign crypto algorithms available have been expanded to keep up with evolving cryptography. The following table shows the available elfsign algorithms: Elfsign Algorithm Solaris Release Comments elfsign sign -F rsa_md5_sha1   S10, S11.0, S11.1 Default for S10. Not recommended* elfsign sign -F rsa_sha1 S11.1 Default for S11.1. Not recommended elfsign sign -F rsa_sha256 S11.1 patch SRU7+   Recommended ___ *Most or all CAs do not accept MD5 CSRs and do not issue MD5 certs due to MD5 hash collision problems. RSA Key Length. I recommend using RSA-2048 key length with elfsign is RSA-2048 as the best balance between a long expected "life time", interoperability, and performance. RSA-2048 keys have an expected lifetime through 2030 (and probably beyond). For details, see Recommendation for Key Management: Part 1: General, NIST Publication SP 800-57 part 1 (rev. 3, 7/2012, PDF), tables 2 and 4 (pp. 64, 67). Step 1: create or obtain a key and cert The first step in using elfsign is to obtain a key and cert from a public Certificate Authority (CA), or create your own self-signed key and cert. I'll briefly explain both methods. Obtaining a Certificate from a CA To obtain a cert from a CA, such as Verisign, Thawte, or Go Daddy (to name a few random examples), you create a private key and a Certificate Signing Request (CSR) file and send it to the CA, following the instructions of the CA on their website. They send back a signed public key certificate. The public key cert, along with the private key you created is used by elfsign to sign an ELF file. The public key cert is distributed with the software and is used by elfsign to verify elfsign signatures in ELF files. You need to request a RSA "Class 3 public key certificate", which is used for servers and software signing. Elfsign uses RSA and we recommend RSA-2048 keys. The private key and CSR can be generated with openssl(1) or pktool(1) on Solaris. Here's a simple example that uses pktool to generate a private RSA_2048 key and a CSR for sending to a CA: $ pktool gencsr keystore=file format=pem outcsr=MYCSR.p10 \ subject="CN=canineswworks.com,OU=Canine SW object signing" \ outkey=MYPRIVATEKEY.key $ openssl rsa -noout -text -in MYPRIVATEKEY.key Private-Key: (2048 bit) modulus: 00:d2:ef:42:f2:0b:8c:96:9f:45:32:fc:fe:54:94: . . . [omitted for brevity] . . . c9:c7 publicExponent: 65537 (0x10001) privateExponent: 26:14:fc:49:26:bc:a3:14:ee:31:5e:6b:ac:69:83: . . . [omitted for brevity] . . . 81 prime1: 00:f6:b7:52:73:bc:26:57:26:c8:11:eb:6c:dc:cb: . . . [omitted for brevity] . . . bc:91:d0:40:d6:9d:ac:b5:69 prime2: 00:da:df:3f:56:b2:18:46:e1:89:5b:6c:f1:1a:41: . . . [omitted for brevity] . . . f3:b7:48:de:c3:d9:ce:af:af exponent1: 00:b9:a2:00:11:02:ed:9a:3f:9c:e4:16:ce:c7:67: . . . [omitted for brevity] . . . 55:50:25:70:d3:ca:b9:ab:99 exponent2: 00:c8:fc:f5:57:11:98:85:8e:9a:ea:1f:f2:8f:df: . . . [omitted for brevity] . . . 23:57:0e:4d:b2:a0:12:d2:f5 coefficient: 2f:60:21:cd:dc:52:76:67:1a:d8:75:3e:7f:b0:64: . . . [omitted for brevity] . . . 06:94:56:d8:9d:5c:8e:9b $ openssl req -noout -text -in MYCSR.p10 Certificate Request: Data: Version: 2 (0x2) Subject: OU=Canine SW object signing, CN=canineswworks.com Subject Public Key Info: Public Key Algorithm: rsaEncryption Public-Key: (2048 bit) Modulus: 00:d2:ef:42:f2:0b:8c:96:9f:45:32:fc:fe:54:94: . . . [omitted for brevity] . . . c9:c7 Exponent: 65537 (0x10001) Attributes: Signature Algorithm: sha1WithRSAEncryption b3:e8:30:5b:88:37:68:1c:26:6b:45:af:5e:de:ea:60:87:ea: . . . [omitted for brevity] . . . 06:f9:ed:b4 Secure storage of RSA private key. The private key needs to be protected if the key signing is used for production (as opposed to just testing). That is, protect the key to protect against unauthorized signatures by others. One method is to use a PIN-protected PKCS#11 keystore. The private key you generate should be stored in a secure manner, such as in a PKCS#11 keystore using pktool(1). Otherwise others can sign your signature. Other secure key storage mechanisms include a SCA-6000 crypto card, a USB thumb drive stored in a locked area, a dedicated server with restricted access, Oracle Key Manager (OKM), or some combination of these. I also recommend secure backup of the private key. Here's an example of generating a private key protected in the PKCS#11 keystore, and a CSR. $ pktool setpin # use if PIN not set yet Enter token passphrase: changeme Create new passphrase: Re-enter new passphrase: Passphrase changed. $ pktool gencsr keystore=pkcs11 label=MYPRIVATEKEY \ format=pem outcsr=MYCSR.p10 \ subject="CN=canineswworks.com,OU=Canine SW object signing" $ pktool list keystore=pkcs11 Enter PIN for Sun Software PKCS#11 softtoken: Found 1 asymmetric public keys. Key #1 - RSA public key: MYPRIVATEKEY Here's another example that uses openssl instead of pktool to generate a private key and CSR: $ openssl genrsa -out cert.key 2048 $ openssl req -new -key cert.key -out MYCSR.p10 Self-Signed Cert You can use openssl or pktool to create a private key and a self-signed public key certificate. A self-signed cert is useful for development, testing, and internal use. The private key created should be stored in a secure manner, as mentioned above. The following example creates a private key, MYSELFSIGNED.key, and a public key cert, MYSELFSIGNED.pem, using pktool and displays the contents with the openssl command. $ pktool gencert keystore=file format=pem serial=0xD06F00D lifetime=20-year \ keytype=rsa hash=sha256 outcert=MYSELFSIGNED.pem outkey=MYSELFSIGNED.key \ subject="O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com" $ pktool list keystore=file objtype=cert infile=MYSELFSIGNED.pem Found 1 certificates. 1. (X.509 certificate) Filename: MYSELFSIGNED.pem ID: c8:24:59:08:2b:ae:6e:5c:bc:26:bd:ef:0a:9c:54:de:dd:0f:60:46 Subject: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Issuer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Not Before: Oct 17 23:18:00 2013 GMT Not After: Oct 12 23:18:00 2033 GMT Serial: 0xD06F00D0 Signature Algorithm: sha256WithRSAEncryption $ openssl x509 -noout -text -in MYSELFSIGNED.pem Certificate: Data: Version: 3 (0x2) Serial Number: 3496935632 (0xd06f00d0) Signature Algorithm: sha256WithRSAEncryption Issuer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Validity Not Before: Oct 17 23:18:00 2013 GMT Not After : Oct 12 23:18:00 2033 GMT Subject: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Subject Public Key Info: Public Key Algorithm: rsaEncryption Public-Key: (2048 bit) Modulus: 00:bb:e8:11:21:d9:4b:88:53:8b:6c:5a:7a:38:8b: . . . [omitted for brevity] . . . bf:77 Exponent: 65537 (0x10001) Signature Algorithm: sha256WithRSAEncryption 9e:39:fe:c8:44:5c:87:2c:8f:f4:24:f6:0c:9a:2f:64:84:d1: . . . [omitted for brevity] . . . 5f:78:8e:e8 $ openssl rsa -noout -text -in MYSELFSIGNED.key Private-Key: (2048 bit) modulus: 00:bb:e8:11:21:d9:4b:88:53:8b:6c:5a:7a:38:8b: . . . [omitted for brevity] . . . bf:77 publicExponent: 65537 (0x10001) privateExponent: 0a:06:0f:23:e7:1b:88:62:2c:85:d3:2d:c1:e6:6e: . . . [omitted for brevity] . . . 9c:e1:e0:0a:52:77:29:4a:75:aa:02:d8:af:53:24: c1 prime1: 00:ea:12:02:bb:5a:0f:5a:d8:a9:95:b2:ba:30:15: . . . [omitted for brevity] . . . 5b:ca:9c:7c:19:48:77:1e:5d prime2: 00:cd:82:da:84:71:1d:18:52:cb:c6:4d:74:14:be: . . . [omitted for brevity] . . . 5f:db:d5:5e:47:89:a7:ef:e3 exponent1: 32:37:62:f6:a6:bf:9c:91:d6:f0:12:c3:f7:04:e9: . . . [omitted for brevity] . . . 97:3e:33:31:89:66:64:d1 exponent2: 00:88:a2:e8:90:47:f8:75:34:8f:41:50:3b:ce:93: . . . [omitted for brevity] . . . ff:74:d4:be:f3:47:45:bd:cb coefficient: 4d:7c:09:4c:34:73:c4:26:f0:58:f5:e1:45:3c:af: . . . [omitted for brevity] . . . af:01:5f:af:ad:6a:09:bf Step 2: Sign the ELF File object By now you should have your private key, and obtained, by hook or crook, a cert (either from a CA or use one you created (a self-signed cert). The next step is to sign one or more objects with your private key and cert. Here's a simple example that creates an object file, signs, verifies, and lists the contents of the ELF signature. $ echo '#include <stdio.h>\nint main(){printf("Hello\\n");}'>hello.c $ make hello cc -o hello hello.c $ elfsign verify -v -c MYSELFSIGNED.pem -e hello elfsign: no signature found in hello. $ elfsign sign -F rsa_sha256 -v -k MYSELFSIGNED.key -c MYSELFSIGNED.pem -e hello elfsign: hello signed successfully. format: rsa_sha256. signer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com. signed on: October 17, 2013 04:22:49 PM PDT. $ elfsign list -f format -e hello rsa_sha256 $ elfsign list -f signer -e hello O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com $ elfsign list -f time -e hello October 17, 2013 04:22:49 PM PDT $ elfsign verify -v -c MYSELFSIGNED.key -e hello elfsign: verification of hello failed. format: rsa_sha256. signer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com. signed on: October 17, 2013 04:22:49 PM PDT. Signing using the pkcs11 keystore To sign the ELF file using a private key in the secure pkcs11 keystore, replace "-K MYSELFSIGNED.key" in the "elfsign sign" command line with "-T MYPRIVATEKEY", where MYPRIVATKEY is the pkcs11 token label. Step 3: Install the cert and test on another system Just signing the object isn't enough. You need to copy or install the cert and the signed ELF file(s) on another system to test that the signature is OK. Your public key cert should be installed in /etc/certs. Use elfsign verify to verify the signature. Elfsign verify checks each cert in /etc/certs until it finds one that matches the elfsign signature in the file. If one isn't found, the verification fails. Here's an example: $ su Password: # rm /etc/certs/MYSELFSIGNED.key # cp MYSELFSIGNED.pem /etc/certs # exit $ elfsign verify -v hello elfsign: verification of hello passed. format: rsa_sha256. signer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com. signed on: October 17, 2013 04:24:20 PM PDT. After testing, package your cert along with your ELF object to allow elfsign verification after your cert and object are installed or copied. Under the Hood: elfsign verification Here's the steps taken to verify a ELF file signed with elfsign. The steps to sign the file are similar except the private key exponent is used instead of the public key exponent and the .SUNW_signature section is written to the ELF file instead of being read from the file. Generate a digest (SHA-256) of the ELF file sections. This digest uses all ELF sections loaded in memory, but excludes the ELF header, the .SUNW_signature section, and the symbol table Extract the RSA signature (RSA-2048) from the .SUNW_signature section Extract the RSA public key modulus and public key exponent (65537) from the public key cert Calculate the expected digest as follows:     signaturepublicKeyExponent % publicKeyModulus Strip the PKCS#1 padding (most significant bytes) from the above. The padding is 0x00, 0x01, 0xff, 0xff, . . ., 0xff, 0x00. If the actual digest == expected digest, the ELF file is verified (OK). Further Information elfsign(1), pktool(1), and openssl(1) man pages. "Signed Solaris 10 Binaries?" blog by Darren Moffat (2005) shows how to use elfsign. "Simple CLI based CA on Solaris" blog by Darren Moffat (2008) shows how to set up a simple CA for use with self-signed certificates. "How to Create a Certificate by Using the pktool gencert Command" System Administration Guide: Security Services (available at docs.oracle.com)

  Read the article

• CodePlex Daily Summary for Tuesday, November 01, 2011

  CodePlex Daily Summary for Tuesday, November 01, 2011Popular ReleasesAgFx Windows Phone Application Data Caching Framework: AgFx November Update: This update is primarily a bug fix release, which provides a number of stability and performance enhancements to AgFx. Available as a NuGet package here. Release Notes Fix IsoStore exceptions during shutdown (Changelist 81729) Thread safety and sequencings issues (Changelists 78682,79252, 80707) Fix landscape layout issue in auth sample Fix async keyword collision Supporting overlapping/multiple notifications for Load requestsiTuner - The iTunes Companion: iTuner 1.4.4322: Added German (unverified, apologies if incorrect) Properly source invariant resources with correct resIDs Replaced obsolete lyric providers with working providers Fix Pseudolater to correctly morph every third char Fix null reference in CatalogBaseDevpad: 4.6: Whats new for Devpad 4.6: New Recent Files New Run in Safari Minor Bug Fix's, improvements and speed upsWindows Workflow Foundation on Codeplex: Microsoft.Activities v1.8.8: Microsoft.Activities Overview How do I install Microsoft.Activities? Updates in this release9318Technical Analysis Engine for .NET: Technical Analysis Engine 1.25: What's new in the 1.25 release (2011-11-01): - Added Williams %R indicator - Added Moving Average Envelopes indicatorBF3Rcon.NET: BF3Rcon 3.0: This release is targeted for RCON documentation based on R3. Everything should be beta stable, but it's alpha because I haven't been able to fully test it. When a stable release is ready, a proper changelog will be kept. Important Edit: There's one method that will keep this from working in Mono. GeneratePasswordHash uses void HashAlgorithm.Dispose(), which isn't in Mono. This will have to be changed to Clear() in the next release. If anyone needs a Mono version of this immediately, you can...BoxWorld: BoxWorld_2011.10.30: BoxWorld - 8.0.1110.30 This is the initial release of BoxWorld. I'd recommend downloading the installer as it contains the compiled code and everything all nicely contained. By default, you end up with this directory structure: C:\Program Files\ViperWorks\BoxWorld C:\Program Files\ViperWorks\BoxWorld\Data C:\Program Files\ViperWorks\BoxWorld\Interface C:\Program Files\ViperWorks\BoxWorld\Source In the root you have the compiled EXE files, one for the main release, one for the LITE release ...VidCoder: 1.2.1: Fixed a couple regressions: video encoder was blank in queue and crashes with the High Profile preset when opening the Settings window. Fixed problem with auto-update introduced in 1.2.0. If you have 1.2.0 you will need to update manually to get this.AssaultCube Reloaded: Release 2.3: THE RELEASE YOU'VE ALL BEEN WAITING FOR! IT CAN NOW BE CONSIDERED STABLE Linux has Debian 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, download the Linux package. The server pack is ready for both Windows and Linux, but you might need to compile your own for linux (source included) If you are using Windows and require the source code, download the source package!Koober: Koober - The Ebook Creator 0.2: The official release of Koober as Open source. Koober is a ebook creator for Windows, and Koob Reader is the reader.A Microblog API (SINA weibo.com open API in C#, .Net???????API): AMicroblogAPI v1.0: AMicroBlogAPI is a C# implementation, a strong-typed deep encapsulation, a easy-to-use .net wrapper of SINA microblog API v1.0. App developers no longer need to parse various HTTP responses -- all responses are parsed into strong types; No longer need to construt the request query strings -- just simply gives the values of parameters; No longer need to implement the OAuth -- a single call could logs the user on. In this release (AMicroblogAPI v1.0), all basic data APIs are implemented. For ...patterns & practices: Enterprise Library Contrib: Enterprise Library Contrib - 5.0 (Oct 2011): This release of Enterprise Library Contrib is based on the Microsoft patterns & practices Enterprise Library 5.0 core and contains the following: Common extensionsTypeConfigurationElement<T> - A Polymorphic Configuration Element without having to be part of a PolymorphicConfigurationElementCollection. AnonymousConfigurationElement - A Configuration element that can be uniquely identified without having to define its name explicitly. Data Access Application Block extensionsMySql Provider - ...Network Monitor Open Source Parsers: Network Monitor Parsers 3.4.2748: The Network Monitor Parsers packages contain parsers for more than 400 network protocols, including RFC based public protocols and protocols for Microsoft products defined in the Microsoft Open Specifications for Windows and SQL Server. NetworkMonitor_Parsers.msi is the base parser package which defines parsers for commonly used public protocols and protocols for Microsoft Windows. In this release, NetowrkMonitor_Parsers.msi continues to improve quality and fix bugs. It has included the fo...Duckworth Lewis Professional Edition Calculator: DLcalc 3.0: DLcalc 3.0 can perform Duckworth/Lewis Professional Edition calculations 100% accurately. It also produces over-by-over and ball-by-ball PAR score tables.Media Companion: MC 3.420b Weekly: Ensure .NET 4.0 Full Framework is installed. (Available from http://www.microsoft.com/download/en/details.aspx?id=17718) Ensure the NFO ID fix is applied when transitioning from versions prior to 3.416b. (Details here) Movies Fixed: Fanart and poster scraping issues TV Shows (Re)Added: Rebuild single show Fixed: Issue when shows are moved from original location Ability to handle " for actor nicknames Crash when episode name contains "<" (does not scrape yet) Clears fanart when switch...patterns & practices - Unity: Unity 3.0 for .NET4.5 Preview: The Unity 3.0.1026.0 Preview enables Unity to work on .NET 4.5 with both the WinRT and desktop profiles. The major changes include: Unity projects updated to target .NET 4.5. Dynamic build plans modified to use compiled lambda expressions instead of Reflection.Emit Converting reflection to use the new TypeInfo for reflection. Projects updated to work with the Microsoft Visual Studio 2011 Preview Notes/Known Issues: The Microsoft.Practices.Unity.UnityServiceLocator class cannot be use...Managed Extensibility Framework: MEF 2 Preview 4: Detailed information on this release is available on the BCL team blog.AcDown????? - Anime&Comic Downloader: AcDown????? v3.6: ?? ● AcDown??????????、??????，??????????????????????，???????Acfun、Bilibili、???、???、???、Tucao.cc、SF???、?????80????，???????????、?????????。 ● AcDown???????????????????????????，???，???????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)?.NET Framework 2.0???(x64)，?????"?????????"??? ??????????????，??????????： ??"AcDown?????"????????? ?? v3.6?? ??“????”...MVC Controls Toolkit: Mvc Controls Toolkit 1.5.0: Added: The new Client Blocks feaure of Views A new "move" js method for the TreeViews The NewHtmlCreated js event to the DataGrid Improved the ChoiceList structure that now allows also the selection list of a dropdown to be chosen with a lambda expression Improved the AcceptViewHintAttribute controller filter. Now a client can specify not only the name of a View or Partial View it prefers, but also to receive just the rough data in Json format. Now the the SMinimum and SMaximum par...Free SharePoint Master Pages: Buried Alive (Halloween) Theme: Release Notes *Created for Halloween, you will find theme file, custom css file and images. *Created by Al Roome @AlstarRoome Features: Custom styling for web part Custom background *Screenshot https://s3.amazonaws.com/kkhipple/post/sharepoint-showcase-halloween.pngNew ProjectsarlTH: "Airport Link Thailand" Application for Windows Phone 7.1Audio Tags Editor For Excel: The purpose of the project is to create a tool to edit tags of audio files through the excel application. The program is an Excel add-in.AW Load Tester: AW Load Tester is a simple and easy to use website load tester that very closely mimics a regular users browsing session on your website. Many popular load tester only download HTML. AW Load Tester downloads all the related items on a page simultaneously. AzMan - Be Good Do Right !: The AzMan is a collection of reusable software components designed to assist software developers with common enterprise development challenges. http://bbs.fengshupo.com/BestWayWP7UI: The User interface of best wat wp7 applicationCheckout Subsystem Optimizer: Checkout Subsystem OptimizerDBScripter - Library for scripting SQL Server database objects: This project is library that allows users to script SQL Server database objects. Library uses dynamic management views for extracting data about databases objects. This library could be used in various situations. The most interesting areas are comparing database objects and generation database documentation. For both cases examples have been prepared.Dependency Checker: Dependency Checker is a utility for verifying that a set of prerequisites is present on a machine. The set of dependencies is defined in a configuration file. For more information, see http://dependencychecker.codeplex.com/documentation DibTer: DibTer is a brand new CMS for ASP.NET Mainly features are NHibernate MVC JQuery HTML5Dynamics CRM Entity Based Stress Tool: Entity Based Stress Tool, is command line program that creates configurable server agents in order to stress a defined entity at a defined Message/Stage. This tool allows CRM Application Stressing, Plugin Stressing, and enlaborate an execution report.Edinger: Edinger is a simple text editor.FreeboxHDVideoPlayer: FreeboxHDVideoPlayer makes it easier for free.fr french ISP users to play and manage videos stored on the HDD of the Freebox HD. FreeboxHDVideoPlayer simplifie, pour les utilisateurs de free.fr, la lecture et la gestion des vidéos stockées sur le disque du boitier Freebox HD.guglex - google docs xtraz: my studying project for asp.net mvc 3. now displaying spreadsheet rows in card viewIP-Camera MJPEG HTTP Web-Server Emulator: Turns web-camera into IP-camera with mjpeg streaming and access it over network. Usage of i-Lids (Imagery Library for Intelligent Detection Systems) and other data for surveillance systems development. Sends WMV, folder with images, web-camera data over the wire.LIM: LIM is .net software for archive manage.Luminji.CorWeb: luminji's company web.Map Generator: Map Generator for your Civ/Col/Roguelike games in VB.NET.Microformat Parsers for .NET: Microformat's Parsers for .NET helps you to collect information you run into on the web, that is stored by means of microformats. It's written in C# 3.0.Mini Rx: Mini Rx provides LINQ like queries over events for C# and F# using extension methods, somewhat like the Reactive Extensions (Rx) but in a lightweight open source package with one non-strong named assembly.MVC Music Store by NNT: Demo Music Store Follow tut from Microsoft. Team Explorer VS 2010 .NET 4PHP MySQL Web Site Creator: PHP MySQL Web Site Creator helps you create a basic template for your web site using a UI form. I creates all PHP, CSS, HTML basic pages to connect to MySQL database.PQLRD: Paco KLk!Project Web And Application: Project MobileStore in ASP use ASP.NET MVC 3RoboZip: RoboZip combines MS Robocopy and Zip-functionality. Create a job and RoboZip will zip all files (from a list of filetypes) within a time span in the past. The zip file name can contain date and time values of the time period it covers. It's developed in C#. The zip component is the DotNetZip Library from http://dotnetzip.codeplex.com. The logging is done using Apache log4net from http://logging.apache.org/log4net. The idea here is not to only present the code, but also to document how the de...Scriptster Gearbox: Scriptster Gearbox is a full C# scripting system based on Scriptster (also on CodePlex). It is aimed at Visual Studio developers and power users who need to automate the sorts of things that DOS is generally good at, but which using C# can make more powerful and more familiar.Technical Analysis Engine for .NET: Technical Analysis Engine is a .NET based library for technical analysis. It is fast, free, easy to use and provides functionality for financial market analysis.ValidationDSL: A Fluent validation engine with ease to use and reusable around the multi-tenant applicationsWebFormsUtilities: WebFormsUtilities is a collection of tools that assist in using MVC/MVP functionality to webforms in an unobtrusive manner. This differs from a hybrid MVC/WebForms page in that you can use methods like UpdateModel() or TryValidateModel() in a WebForms Page class.Wen - WPF 3D Navigator: Control the camera and the lights of a WPF 3D application without any code modification.WindStudios: WindStudiosWrite My Expect Statement: Have Rhino Mocks automatically generate your expect() and return() statements for you.zion xtraz: some basic helpful classes for use in every project

  Read the article

• CodePlex Daily Summary for Thursday, April 05, 2012

  CodePlex Daily Summary for Thursday, April 05, 2012Popular ReleasesCommunity TFS Build Extensions: April 2012: Release notes to follow...ClosedXML - The easy way to OpenXML: ClosedXML 0.65.2: Aside from many bug fixes we now have Conditional Formatting The conditional formatting was sponsored by http://www.bewing.nl (big thanks) New on v0.65.1 Fixed issue when loading conditional formatting with default values for icon sets New on v0.65.2 Fixed issue loading conditional formatting Improved inserts performanceLiberty: v3.2.0.0 Release 4th April 2012: Change Log-Added -Halo 3 support (invincibility, ammo editing) -Halo 3: ODST support (invincibility, ammo editing) -The file transfer page now shows its progress in the Windows 7 taskbar -"About this build" settings page -Reach Change what an object is carrying -Reach Change which node a carried object is attached to -Reach Object node viewer and exporter -Reach Change which weapons you are carrying from the object editor -Reach Edit the weapon controller of vehicles and turrets -An error dia...MSBuild Extension Pack: April 2012: Release Blog Post The MSBuild Extension Pack April 2012 release provides a collection of over 435 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUID’...DotNetNuke® Community Edition CMS: 06.01.05: Major Highlights Fixed issue that stopped users from creating vocabularies when the portal ID was not zero Fixed issue that caused modules configured to be displayed on all pages to be added to the wrong container in new pages Fixed page quota restriction issue in the Ribbon Bar Removed restriction that would not allow users to use a dash in page names. Now users can create pages with names like "site-map" Fixed issue that was causing the wrong container to be loaded in modules wh...51Degrees.mobi - Mobile Device Detection and Redirection: 2.1.3.1: One Click Install from NuGet Changes to Version 2.1.3.11. [assembly: AllowPartiallyTrustedCallers] has been added back into the AssemblyInfo.cs file to prevent failures with other assemblies in Medium trust environments. 2. The Lite data embedded into the assembly has been updated to include devices from December 2011. The 42 new RingMark properties will return Unknown if RingMark data is not available. Changes to Version 2.1.2.11Code Changes 1. The project is now licenced under the Mozilla...MVC Controls Toolkit: Mvc Controls Toolkit 2.0.0: Added Support for Mvc4 beta and WebApi The SafeqQuery and HttpSafeQuery IQueryable implementations that works as wrappers aroung any IQueryable to protect it from unwished queries. "Client Side" pager specialized in paging javascript data coming either from a remote data source, or from local data. LinQ like fluent javascript api to build queries either against remote data sources, or against local javascript data, with exactly the same interface. There are 3 different query objects exp...ExtAspNet: ExtAspNet v3.1.2: ExtAspNet - ?? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ?????????? ExtAspNet ????? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ??????????。 ExtAspNet ??????? JavaScript，?? CSS，?? UpdatePanel，?? ViewState，?? WebServices ???????。 ??????: IE 7.0, Firefox 3.6, Chrome 3.0, Opera 10.5, Safari 3.0+ ????：Apache License 2.0 (Apache) ??：http://extasp.net/ ??：http://bbs.extasp.net/ ??：http://extaspnet.codeplex.com/ ??：http://sanshi.cnblogs.com/ ????： +2012-04-04 v3.1.2 -??IE?????????????BUG（??"about:blank"?...nopCommerce. Open source shopping cart (ASP.NET MVC): nopcommerce 2.50: Highlight features & improvements: • Significant performance optimization. • Allow store owners to create several shipments per order. Added a new shipping status: “Partially shipped”. • Pre-order support added. Enables your customers to place a Pre-Order and pay for the item in advance. Displays “Pre-order” button instead of “Buy Now” on the appropriate pages. Makes it possible for customer to buy available goods and Pre-Order items during one session. It can be managed on a product variant ...WiX Toolset: WiX v3.6 RC0: WiX v3.6 RC0 (3.6.2803.0) provides support for VS11 and a more stable Burn engine. For more information see Rob's blog post about the release: http://robmensching.com/blog/posts/2012/4/3/WiX-v3.6-Release-Candidate-Zero-availableSageFrame: SageFrame 2.0: Sageframe is an open source ASP.NET web development framework developed using ASP.NET 3.5 with service pack 1 (sp1) technology. It is designed specifically to help developers build dynamic website by providing core functionality common to most web applications.iTuner - The iTunes Companion: iTuner 1.5.4475: Fix to parse empty playlists in iTunes LibraryDocument.Editor: 2012.2: Whats New for Document.Editor 2012.2: New Save Copy support New Page Setup support Minor Bug Fix's, improvements and speed upsDotNet.Highcharts: DotNet.Highcharts 1.2 with Examples: Tested and adapted to the latest version of Highcharts 2.2.1 Fixed Issue 359: Not implemented serialization array of type: System.Drawing.Color[] Fixed Issue 364: Crosshairs defined as array of CrosshairsForamt generates bad Highchart code For the example project: Added newest version of Highcharts 2.2.1 Added new demos to How To's section: Bind Data From Dictionary Bind Data From Object List Custom Theme Tooltip Crosshairs Theming The Reset Button Plot Band EventsVidCoder: 1.3.2: Added option for the minimum title length to scan. Added support to enable or disable LibDVDNav. Added option to prompt to delete source files after clearing successful completed items. Added option to disable remembering recent files and folders. Tweaked number box to only select all on a quick click.MJP's DirectX 11 Samples: Light Indexed Deferred Rendering: Implements light indexed deferred using per-tile light lists calculated in a compute shader, as well as a traditional deferred renderer that uses a compute shader for per-tile light culling and per-pixel shading.Pcap.Net: Pcap.Net 0.9.0 (66492): Pcap.Net - March 2012 Release Pcap.Net is a .NET wrapper for WinPcap written in C++/CLI and C#. It Features almost all WinPcap features and includes a packet interpretation framework. Version 0.9.0 (Change Set 66492)March 31, 2012 release of the Pcap.Net framework. Follow Pcap.Net on Google+Follow Pcap.Net on Google+ Files Pcap.Net.DevelopersPack.0.9.0.66492.zip - Includes all the tutorial example projects source files, the binaries in a 3rdParty directory and the documentation. It include...Extended WPF Toolkit: Extended WPF Toolkit - 1.6.0: Want an easier way to install the Extended WPF Toolkit?The Extended WPF Toolkit is available on Nuget. What's in the 1.6.0 Release?BusyIndicator ButtonSpinner Calculator CalculatorUpDown CheckListBox - Breaking Changes CheckComboBox - New Control ChildWindow CollectionEditor CollectionEditorDialog ColorCanvas ColorPicker DateTimePicker DateTimeUpDown DecimalUpDown DoubleUpDown DropDownButton IntegerUpDown Magnifier MaskedTextBox MessageBox MultiLineTex...Media Companion: MC 3.434b Release: General This release should be the last beta for 3.4xx. If there are no major problems, by the end of the week it will upgraded to 3.500 Stable! The latest mc_com.exe should be included too! TV Bug fix - crash when using XBMC scraper for TV episodes. Bug fix - episode count update when adding new episodes. Bug fix - crash when actors name was missing. Enhanced TV scrape progress text. Enhancements made to missing episodes display. Movies Bug fix - hide "Play Trailer" when multisaev...Better Explorer: Better Explorer 2.0.0.831 Alpha: - A new release with: - many bugfixes - changed icon - added code for more failsafe registry usage on x64 systems - not needed regfix anymore - added ribbon shortcut keys - Other fixes Note: If you have problems opening system libraries, a suggestion was given to copy all of these libraries and then delete the originals. Thanks to Gaugamela for that! (see discussion here: 349015 ) Note2: I was upload again the setup due to missing file!New Projects20120229Site1: 29/02/2012 site5B12: Un servizio WCF .NET 4.0 fruibile in modalità REST da Android e IOS IPhone e IPad. Realizzato dai ragazzi di 5BI Informatica dell'ITIS L. Da Vinci - Rimini A.S. 2011/12Accept Language Setter: Accept Language Setter is a System Tray application that lets you quickly set your browser's Accept Language without having to navigate through your browser's menus. It is ideal for developers and testers who work on internationalized websites and need to switch languages often.AGatherBot: C# 5.0 (.NET Framework 4.5) based Counter-Strike 1.6 Gatherbot, highly extensible (using MEF) and configurable.Aweber API .NET SDK: The Aweber API .NET SDK makes it easier communicating with Aweber's API. It covers the basic parts of the API including, lists, subscribers, campaigns and accounts. It is developed in C# .NET 4.0CINET: Continuous Integration Server developed in .Net with MonoClipster: Manage & watch your videos instantly. A project for the course Human Computer Interaction, CS3240 in National University of SingaporeDyna Bomber: With my friend we will try to reborn old game called Dyna Bober.Fer. CR: Pruebas de Software 2012 - DemoFreeDAM: While looking at DAM (Digital Asset Management) solutions, I have found that some of the paid versions are actually just putting a front-end on top of free tools that are actually doing the heavy lifting. This project will give you the freedom to choose a free-dam solution.golang: Go language LLVM compilerHSDLL: HSDLLJsQueryExpression: JsQueryExpression aims to create a javascript library to generate URIs by using QueryExpression (name is inspired from Microsoft Dynamics CRM but structure is different) object model to query OData resources.KunalPishewsccsemb: KunalPishewsccsembLightFarsiDictionary - ??????? ??? ?????/???????: A light weight farsi-english / engilsh-farsi dictionary optimized for fixing common typo mistakes. ??????? ??? ? ???? ????? ?? ??????? / ??????? ?? ????? ?? ???? ?????? ?????? ?????? ?? ????? ?? ???.losezhang: ???TFS??，???30????！MIC Thailand #9 Foursquare: Sample for Maps and GeolocatiohnMtk: Mtk is a toolkit for ASP.NET MVC and FluentNHibernate.MyTest: test test testOpenSocial container on .NET: .NET implementation of OpenSocial containerOrchard Bootstrap: Bootstrap is an Orchard theme constructed using the Bootstrap template system from Twitter.PetroManager: this is a basic data management application.Portable Xna Components: Portable Xna Components makes it easier and faster for Xna game developers to create their games. Developers using this library don't have to worry about rudimentary tasks like drawing and collision detection. It is written in C#Project Management Plug-Ins: Restores functionality to create Microsoft Visio diagrams from Microsoft Project data, via a Microsoft Project AddIn.Project vit: some projectpruebas2012-1: demo de pruebas de softwarePSW20121: demo de pruebas de swPWS 2012-1: Demo para el curso de PWS UPN Cajamarca 2012 - 1Pws2012-1: Demo de calidad prueba de softwarePWSmodelo-2012-1: Demo Para le curso de pws upnradscommerce: Multi shop ecommerce system for web hoster, retailer for Indian Market and then for others.Randata: A DataProvider framework.Robots In Donutland: A solution for a project at DMU - Intelligent systems and roboticsShopScan - Application WP7 winner of Hackathon le Mobile 2012: Application WP7 winner of Hackathon le Mobile 2012Silverlight Printer Map: This printer map makes it easier for an end user in an enterprise to find and install networked printers. The end user need only find the closest printer on the map of the organization, click on it once and it then allow the program to map the printer, install the driver and set it as default printer. It's developed in C# The backend of this program relies on SharePoint 2010 libraries. See documentation for further information.SquareTasks: Gestionnaire de tâchesStructurizer: A tool to generate tiles for DNA self-assembly. Outputs a 2-dimensional map with corresponding glues which allow for use with any core substrate.WCF Duplex Service on Azure using a Silverlight Client: I had some trouble to build correctly a simple WCF Duplex Service that run on Windows AZURE while the Connection is made anonymously, after a lot of research I decided to share my solutionWord to MS-Test: Converts MS-Word document in a format similiar to FitNesse, to MS-Test source code.WPFModalDialog: Custom modal dialog in Wpf, contains basic controls in dialog window, also allow you to inform user about loading operations, using animated watcherXRM Developer Framework: XRM Developer Framework provides you with a Framework & Tools to easily build Enterprise Dynamics CRM 2011 Solutions using patterns & best practices. The Framework builds on many available technologies such as Visual Studio, CRM Developer Toolkit & Moq.

  Read the article

• CodePlex Daily Summary for Thursday, October 18, 2012

  CodePlex Daily Summary for Thursday, October 18, 2012Popular ReleasesGac Library -- C++ Utilities for GPU Accelerated GUI and Script: Gaclib 0.4.0.0: Gaclib.zip contains the following content GacUIDemo Demo solution and projects Public Source GacUI library Document HTML document. Please start at reference_gacui.html Content Necessary CSS/JPG files for document. Improvements to the previous release Added Windows 8 theme (except tab control, will be provided for the next release) GacUI will choose to use Windows 7 theme or Windows 8 theme as default theme according to OS version Added 1 new demos Template.Window.CustomizedBorder ...Yahoo! UI Library: YUI Compressor for .Net: Version 2.1.1.0 - Sartha (BugFix): - Revered back the embedding of the 2x assemblies.Visual Studio Team Foundation Server Branching and Merging Guide: v2.1 - Visual Studio 2012: Welcome to the Branching and Merging Guide What is new? The Version Control specific discussions have been moved from the Branching and Merging Guide to the new Advanced Version Control Guide. The Branching and Merging Guide and the Advanced Version Control Guide have been ported to the new document style. See http://blogs.msdn.com/b/willy-peter_schaub/archive/2012/10/17/alm-rangers-raising-the-quality-bar-for-documentation-part-2.aspx for more information. Quality-Bar Details Documentatio...D3 Loot Tracker: 1.5.5: Compatible with 1.05.Write Once, Play Everywhere: MonoGame 3.0 (BETA): This is a beta release of the up coming MonoGame 3.0. It contains an Installer which will install a binary release of MonoGame on windows boxes with the following platforms. Windows, Linux, Android and Windows 8. If you need to build for iOS or Mac you will need to get the source code at this time as the installers for those platforms are not available yet. The installer will also install a bunch of Project templates for Visual Studio 2010 , 2012 and MonoDevleop. For those of you wish...Windawesome: Windawesome v1.4.1 x64: Fixed switching of applications across monitors Changed window flashing API (fix your config files) Added NetworkMonitorWidget (thanks to weiwen) Any issues/recommendations/requests for future versions? This is the 64-bit version of the release. Be sure to use that if you are on a 64-bit Windows. Works with "Required DLLs v3".CODE Framework: 4.0.21017.0: See change log in the Documentation section for details.Global Stock Exchange (Hobby Project): Global Stock Exchange - Invst Banking (Hobby Proj): Initial VersionMagelia WebStore Open-source Ecommerce software: Magelia WebStore 2.1: Add support for .net 4.0 to Magelia.Webstore.Client and StarterSite version 2.1.254.3 Scheduler Import & Export feature (for Professional and Entreprise Editions) UTC datetime and timezone support .net 4.5 and Visual Studio 2012 migration client magelia global refactoring release of a nugget package to help developers speed up development http://nuget.org/packages/Magelia.Webstore.Client optimization of the data update mechanism (a.k.a. "burst") Performance improvment of the d...JayData - The cross-platform HTML5 data-management library for JavaScript: JayData 1.2.2: JayData is a unified data access library for JavaScript to CRUD + Query data from different sources like OData, MongoDB, WebSQL, SqLite, HTML5 localStorage, Facebook or YQL. The library can be integrated with Knockout.js or Sencha Touch 2 and can be used on Node.js as well. See it in action in this 6 minutes video Sencha Touch 2 example app using JayData: Netflix browser. What's new in JayData 1.2.2 For detailed release notes check the release notes. Revitalized IndexedDB providerNow you c...JaySvcUtil - generate JavaScript context from OData metadata: JaySvcUtil 1.2.2: You will need the JayData library to use contexts generated with JaySvcUtil! Get it from here: http://jaydata.codeplex.comVFPX: FoxcodePlus: FoxcodePlus - Visual Studio like extensions to Visual FoxPro IntelliSense.Droid Explorer: Droid Explorer 0.8.8.8 Beta: fixed the icon for packages on the desktop fixed the install dialog closing right when it starts removed the link to "set up the sdk for me" as this is no longer supported. fixed bug where the device selection dialog would show, even if there was only one device connected. fixed toolbar from having "gap" between other toolbar removed main menu items that do not have any menus Fiskalizacija za developere: FiskalizacijaDev 1.0: Prva verzija ovog projekta, još je uvijek oznacena kao BETA - ovo znaci da su naša testiranja prošla uspješno :) No, kako mi ne proizvodimo neki software za blagajne, tako sve ovo nije niti isprobano u "realnim" uvjetima - svaka je sugestija, primjedba ili prijava bug-a je dobrodošla. Za sve ovo koristite, molimo, Discussions ili Issue Tracker. U ovom trenutku runtime binary je raspoloživ kao Any CPU za .NET verzije 2.0. Javite ukoliko trebaju i verzije buildane za 32-bit/64-bit kao i za .N...Squiggle - A free open source LAN Messenger: Squiggle 3.2 (Development): NOTE: This is development release and not recommended for production use. This release is mainly for enabling extensibility and interoperability with other platforms. Support for plugins Support for extensions Communication layer and protocol is platform independent (ZeroMQ, ProtocolBuffers) Bug fixes New /invite command Edit the sent message Disable update check NOTE: This is development release and not recommended for production use.AcDown????? - AcDown Downloader Framework: AcDown????? v4.2: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown??????????????????，????????????????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ???? 32??64? ???Linux ????(1)????????Windows XP???，????????.NET Framework 2.0???(x86)，?????"?????????"??? (2)???????????Linux???，????????Mono?? ??2...PHPExcel: PHPExcel 1.7.8: See Change Log for details of the new features and bugfixes included in this release, and methods that are now deprecated. Note changes to the PDF Writer: tcPDF is no longer bundled with PHPExcel, but should be installed separately if you wish to use that 3rd-Party library with PHPExcel. Alternatively, you can choose to use mPDF or DomPDF as PDF Rendering libraries instead: PHPExcel now provides a configurable wrapper allowing you a choice of PDF renderer. See the documentation, or the PDF s...DirectX Tool Kit: October 12, 2012: October 12, 2012 Added PrimitiveBatch for drawing user primitives Debug object names for all D3D resources (for PIX and debug layer leak reporting)Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.70: Fixed issue described in discussion #399087: variable references within case values weren't getting resolved.GoogleMap Control: GoogleMap Control 6.1: Some important bug fixes and couple of new features were added. There are no major changes to the sample website. Source code could be downloaded from the Source Code section selecting branch release-6.1. Thus just builds of GoogleMap Control are issued here in this release. Update 14.Oct.2012 - Client side access fixed NuGet Package GoogleMap Control 6.1 NuGet Package FeaturesBounds property to provide ability to create a map by center and bounds as well; Setting in markup <artem:Goog...New ProjectsAnonymous InfoPath Browser Forms Web Part: Web part for SharePoint 2007 and 2010 that enables the anonymous submission of InfoPath forms.ath sem5 gr3 proj1: just a simple app to learn how to work in groups, just a start in our programming careerAtif M DNNTaskManager: This is a simple task manager AWS for .NET Sample (Amazon EC2, S3, SQS, DynamoDB): Amazon Web Services (AWS) Sample for .NET (C#) with Asp.NET MVC and Web API. Including S3, DynamoDB, Elastic Beanstalk and SQSCodingWheels.DataTypes: DataTypes tries to make it easier for developers to have concrete typesafe objects for working with many common forms of data. Many times these data objects are just doubles or ints floating through your code with abbreviations on them describing what they represent.Display attachments (list view) SP 2010: Display attachments (SP 2010) is a field for all type lists without types: Document library, Image library, Links, Surveys.Donation Tracker: This is a school projectEveHQ : The Internet Spaceship Toolkit: Multi-faceted character application for Eve-Online. Includes pilot monitoring, skill queue planning, ship fitting, industry and more.EventConni: EventConniFileCloud.Net: FileCloud.NET is a .Net wrapper for http://filecloud.io/ service API.Foodies: FoodiesForce PowerPivot Refresh: This project contains an c# utility class (CustomDataRefreshUtils) to refresh a PowerPivot file in SharePoint 2010. Geometric Modeling: REnder a mesh with Visual Studio - C#Heavysoft Mince: Heavysoft Mince is an opportunity to enhance my skills and to show how free software can be used in enterprise-level systems.HP iLO Management Utility: A small utility to provide a nice interface for managing multiple servers over the iLO interface.iMeeting: iMeeting is a simple application built in Java. iTask: iTask for Windows 8 LamWebOS: this is test project.MackProjects_Musicallis: Projeto da disciplina de Técnicas de Programação Aplicada II da Universidade Presbiteriana Mackenzie - SP.Merge PDF: MergePDF is an easy and simple tool which could help you batch merge PDF files (any number you want) into one PDF file quickly. It is completely free. With MerNetGen: O NetGen é um projeto de geração automatizada de interface Web em ASP.NET a partir de modelo de classes do LINQ-TO-SQL, estando disponível como um Addin para o Visual Studio 2008.Other Ways: ?? ! ????!!!!!Physical Therapy Timer: A simple Windows application that makes it easy to set a countdown timer for a required time period, and keep track of how many times the timer has be run.PicoMax: This version of PicoMax has everything you need to use the Seeed OLED without the MS Graphics class. It can be used in Gadgeteer or a regular NETMF project.post tracker: ASP, WEB API, WINDOWS PhoneRandomEngine: Open Source Game Engine.Resident Raver: This is Windows 8 version of Resident Raver which I wrote for my Intro To HTML5 Game Dev book. It requires the Impact JavaScript game framework.RogueTS: RogueTS is a Roguelike engine written in TypeScript. It features randomly generated maps, basic lighting effects, collision detection and additional stub code.RonYeeStores: ????????????，??C2C?B2C???????????。ShangHaiTunnel monitor: shang hai tunnel projectSharePoint List Security: Free, open source set of features for SharePoint 2010 to enhance the OOTB list permissions by adding column level permissions for users and groups.Skywave Code Lines Counter: It is a tiny program which will count real written lines of code. Real lines means that we removed autogenerated lines, empty lines and single '{' or '}' lines (in C#) and ... Currently supports .cs and .vb files (for C# and VB) It will say how much you worked ;-)switchcontroles: HAT Switch controle sy seguimientoSyscore: Steps : 1 - Definitions 2 - Requirements 3 - Projecting 4 - Delegation 5 - Prototyping 6 - Testing/Analizing 7 - Finalizing 8 - Distribution 9 - Congratulationstarikscodeplexproject: tarikscodeplexprojectTaskManager04: This project is an effort to implement the coding examples given in the TASK MANAGER video series into a working DotNetNuke program.testc: this is a test ,heihei,yongshengtesttom10172012git01: fds fs fs fs tsUnit - TypeScript Unit Testing Framework: tsUnit is a unit testing framework for TypeScript, written in TypeScript. It allows you to encapsulate your test functions in classes and modules.WebGrease: WebGrease is a suite of tools for optimizing javascript, css files and images.????: ??《?????》、《??》、《???》、《??》???。。。

  Read the article

• How to maintain encapsulation with composition in C++?

  - by iFreilicht

  I am designing a class Master that is composed from multiple other classes, A, Base, C and D. These four classes have absolutely no use outside of Master and are meant to split up its functionality into manageable and logically divided packages. They also provide extensible functionality as in the case of Base, which can be inherited from by clients. But, how do I maintain encapsulation of Master with this design? So far, I've got two approaches, which are both far from perfect: 1. Replicate all accessors: Just write accessor-methods for all accessor-methods of all classes that Master is composed of. This leads to perfect encapsulation, because no implementation detail of Master is visible, but is extremely tedious and makes the class definition monstrous, which is exactly what the composition should prevent. Also, adding functionality to one of the composees (is that even a word?) would require to re-write all those methods in Master. An additional problem is that inheritors of Base could only alter, but not add functionality. 2. Use non-assignable, non-copyable member-accessors: Having a class accessor<T> that can not be copied, moved or assigned to, but overrides the operator-> to access an underlying shared_ptr, so that calls like Master->A()->niceFunction(); are made possible. My problem with this is that it kind of breaks encapsulation as I would now be unable to change my implementation of Master to use a different class for the functionality of niceFunction(). Still, it is the closest I've gotten without using the ugly first approach. It also fixes the inheritance issue quite nicely. A small side question would be if such a class already existed in std or boost. EDIT: Wall of code I will now post the code of the header files of the classes discussed. It may be a bit hard to understand, but I'll give my best in explaining all of it. 1. GameTree.h The foundation of it all. This basically is a doubly-linked tree, holding GameObject-instances, which we'll later get to. It also has it's own custom iterator GTIterator, but I left that out for brevity. WResult is an enum with the values SUCCESS and FAILED, but it's not really important. class GameTree { public: //Static methods for the root. Only one root is allowed to exist at a time! static void ConstructRoot(seed_type seed, unsigned int depth); inline static bool rootExists(){ return static_cast<bool>(rootObject_); } inline static weak_ptr<GameTree> root(){ return rootObject_; } //delta is in ms, this is used for velocity, collision and such void tick(unsigned int delta); //Interaction with the tree inline weak_ptr<GameTree> parent() const { return parent_; } inline unsigned int numChildren() const{ return static_cast<unsigned int>(children_.size()); } weak_ptr<GameTree> getChild(unsigned int index) const; template<typename GOType> weak_ptr<GameTree> addChild(seed_type seed, unsigned int depth = 9001){ GOType object{ new GOType(seed) }; return addChildObject(unique_ptr<GameTree>(new GameTree(std::move(object), depth))); } WResult moveTo(weak_ptr<GameTree> newParent); WResult erase(); //Iterators for for( : ) loop GTIterator& begin(){ return *(beginIter_ = std::move(make_unique<GTIterator>(children_.begin()))); } GTIterator& end(){ return *(endIter_ = std::move(make_unique<GTIterator>(children_.end()))); } //unloading should be used when objects are far away WResult unloadChildren(unsigned int newDepth = 0); WResult loadChildren(unsigned int newDepth = 1); inline const RenderObject& renderObject() const{ return gameObject_->renderObject(); } //Getter for the underlying GameObject (I have not tested the template version) weak_ptr<GameObject> gameObject(){ return gameObject_; } template<typename GOType> weak_ptr<GOType> gameObject(){ return dynamic_cast<weak_ptr<GOType>>(gameObject_); } weak_ptr<PhysicsObject> physicsObject() { return gameObject_->physicsObject(); } private: GameTree(const GameTree&); //copying is only allowed internally GameTree(shared_ptr<GameObject> object, unsigned int depth = 9001); //pointer to root static shared_ptr<GameTree> rootObject_; //internal management of a child weak_ptr<GameTree> addChildObject(shared_ptr<GameTree>); WResult removeChild(unsigned int index); //private members shared_ptr<GameObject> gameObject_; shared_ptr<GTIterator> beginIter_; shared_ptr<GTIterator> endIter_; //tree stuff vector<shared_ptr<GameTree>> children_; weak_ptr<GameTree> parent_; unsigned int selfIndex_; //used for deletion, this isn't necessary void initChildren(unsigned int depth); //constructs children }; 2. GameObject.h This is a bit hard to grasp, but GameObject basically works like this: When constructing a GameObject, you construct its basic attributes and a CResult-instance, which contains a vector<unique_ptr<Construction>>. The Construction-struct contains all information that is needed to construct a GameObject, which is a seed and a function-object that is applied at construction by a factory. This enables dynamic loading and unloading of GameObjects as done by GameTree. It also means that you have to define that factory if you inherit GameObject. This inheritance is also the reason why GameTree has a template-function gameObject<GOType>. GameObject can contain a RenderObject and a PhysicsObject, which we'll later get to. Anyway, here's the code. class GameObject; typedef unsigned long seed_type; //this declaration magic means that all GameObjectFactorys inherit from GameObjectFactory<GameObject> template<typename GOType> struct GameObjectFactory; template<> struct GameObjectFactory<GameObject>{ virtual unique_ptr<GameObject> construct(seed_type seed) const = 0; }; template<typename GOType> struct GameObjectFactory : GameObjectFactory<GameObject>{ GameObjectFactory() : GameObjectFactory<GameObject>(){} unique_ptr<GameObject> construct(seed_type seed) const{ return unique_ptr<GOType>(new GOType(seed)); } }; //same as with the factories. this is important for storing them in vectors template<typename GOType> struct Construction; template<> struct Construction<GameObject>{ virtual unique_ptr<GameObject> construct() const = 0; }; template<typename GOType> struct Construction : Construction<GameObject>{ Construction(seed_type seed, function<void(GOType*)> func = [](GOType* null){}) : Construction<GameObject>(), seed_(seed), func_(func) {} unique_ptr<GameObject> construct() const{ unique_ptr<GameObject> gameObject{ GOType::factory.construct(seed_) }; func_(dynamic_cast<GOType*>(gameObject.get())); return std::move(gameObject); } seed_type seed_; function<void(GOType*)> func_; }; typedef struct CResult { CResult() : constructions{} {} CResult(CResult && o) : constructions(std::move(o.constructions)) {} CResult& operator= (CResult& other){ if (this != &other){ for (unique_ptr<Construction<GameObject>>& child : other.constructions){ constructions.push_back(std::move(child)); } } return *this; } template<typename GOType> void push_back(seed_type seed, function<void(GOType*)> func = [](GOType* null){}){ constructions.push_back(make_unique<Construction<GOType>>(seed, func)); } vector<unique_ptr<Construction<GameObject>>> constructions; } CResult; //finally, the GameObject class GameObject { public: GameObject(seed_type seed); GameObject(const GameObject&); virtual void tick(unsigned int delta); inline Matrix4f trafoMatrix(){ return physicsObject_->transformationMatrix(); } //getter inline seed_type seed() const{ return seed_; } inline CResult& properties(){ return properties_; } inline const RenderObject& renderObject() const{ return *renderObject_; } inline weak_ptr<PhysicsObject> physicsObject() { return physicsObject_; } protected: virtual CResult construct_(seed_type seed) = 0; CResult properties_; shared_ptr<RenderObject> renderObject_; shared_ptr<PhysicsObject> physicsObject_; seed_type seed_; }; 3. PhysicsObject That's a bit easier. It is responsible for position, velocity and acceleration. It will also handle collisions in the future. It contains three Transformation objects, two of which are optional. I'm not going to include the accessors on the PhysicsObject class because I tried my first approach on it and it's just pure madness (way over 30 functions). Also missing: the named constructors that construct PhysicsObjects with different behaviour. class Transformation{ Vector3f translation_; Vector3f rotation_; Vector3f scaling_; public: Transformation() : translation_{ 0, 0, 0 }, rotation_{ 0, 0, 0 }, scaling_{ 1, 1, 1 } {}; Transformation(Vector3f translation, Vector3f rotation, Vector3f scaling); inline Vector3f translation(){ return translation_; } inline void translation(float x, float y, float z){ translation(Vector3f(x, y, z)); } inline void translation(Vector3f newTranslation){ translation_ = newTranslation; } inline void translate(float x, float y, float z){ translate(Vector3f(x, y, z)); } inline void translate(Vector3f summand){ translation_ += summand; } inline Vector3f rotation(){ return rotation_; } inline void rotation(float pitch, float yaw, float roll){ rotation(Vector3f(pitch, yaw, roll)); } inline void rotation(Vector3f newRotation){ rotation_ = newRotation; } inline void rotate(float pitch, float yaw, float roll){ rotate(Vector3f(pitch, yaw, roll)); } inline void rotate(Vector3f summand){ rotation_ += summand; } inline Vector3f scaling(){ return scaling_; } inline void scaling(float x, float y, float z){ scaling(Vector3f(x, y, z)); } inline void scaling(Vector3f newScaling){ scaling_ = newScaling; } inline void scale(float x, float y, float z){ scale(Vector3f(x, y, z)); } void scale(Vector3f factor){ scaling_(0) *= factor(0); scaling_(1) *= factor(1); scaling_(2) *= factor(2); } Matrix4f matrix(){ return WMatrix::Translation(translation_) * WMatrix::Rotation(rotation_) * WMatrix::Scale(scaling_); } }; class PhysicsObject; typedef void tickFunction(PhysicsObject& self, unsigned int delta); class PhysicsObject{ PhysicsObject(const Transformation& trafo) : transformation_(trafo), transformationVelocity_(nullptr), transformationAcceleration_(nullptr), tick_(nullptr) {} PhysicsObject(PhysicsObject&& other) : transformation_(other.transformation_), transformationVelocity_(std::move(other.transformationVelocity_)), transformationAcceleration_(std::move(other.transformationAcceleration_)), tick_(other.tick_) {} Transformation transformation_; unique_ptr<Transformation> transformationVelocity_; unique_ptr<Transformation> transformationAcceleration_; tickFunction* tick_; public: void tick(unsigned int delta){ tick_ ? tick_(*this, delta) : 0; } inline Matrix4f transformationMatrix(){ return transformation_.matrix(); } } 4. RenderObject RenderObject is a base class for different types of things that could be rendered, i.e. Meshes, Light Sources or Sprites. DISCLAIMER: I did not write this code, I'm working on this project with someone else. class RenderObject { public: RenderObject(float renderDistance); virtual ~RenderObject(); float renderDistance() const { return renderDistance_; } void setRenderDistance(float rD) { renderDistance_ = rD; } protected: float renderDistance_; }; struct NullRenderObject : public RenderObject{ NullRenderObject() : RenderObject(0.f){}; }; class Light : public RenderObject{ public: Light() : RenderObject(30.f){}; }; class Mesh : public RenderObject{ public: Mesh(unsigned int seed) : RenderObject(20.f) { meshID_ = 0; textureID_ = 0; if (seed == 1) meshID_ = Model::getMeshID("EM-208_heavy"); else meshID_ = Model::getMeshID("cube"); }; unsigned int getMeshID() const { return meshID_; } unsigned int getTextureID() const { return textureID_; } private: unsigned int meshID_; unsigned int textureID_; }; I guess this shows my issue quite nicely: You see a few accessors in GameObject which return weak_ptrs to access members of members, but that is not really what I want. Also please keep in mind that this is NOT, by any means, finished or production code! It is merely a prototype and there may be inconsistencies, unnecessary public parts of classes and such.

  Read the article

• Stack overflow error after creating a instance using 'new'

  - by Justin

  EDIT - The code looks strange here, so I suggest viewing the files directly in the link given. While working on my engine, I came across a issue that I'm unable to resolve. Hoping to fix this without any heavy modification, the code is below. void Block::DoCollision(GameObject* obj){ obj->DoCollision(this); } That is where the stack overflow occurs. This application works perfectly fine until I create two instances of the class using the new keyword. If I only had 1 instance of the class, it worked fine. Block* a = new Block(0, 0, 0, 5); AddGameObject(a); a = new Block(30, 0, 0, 5); AddGameObject(a); Those parameters are just x,y,z and size. The code is checked before hand. Only a object with a matching Collisonflag and collision type will trigger the DoCollision(); function. ((*list1)->m_collisionFlag & (*list2)->m_type) Maybe my check is messed up though. I attached the files concerned here http://celestialcoding.com/index.php?topic=1465.msg9913;topicseen#new. You can download them without having to sign up. The main suspects, I also pasted the code for below. From GameManager.cpp void GameManager::Update(float dt){ GameList::iterator list1; for(list1=m_gameObjectList.begin(); list1 != m_gameObjectList.end(); ++list1){ GameObject* temp = *list1; // Update logic and positions if((*list1)->m_active){ (*list1)->Update(dt); // Clip((*list1)->m_position); // Modify for bounce affect } else continue; // Check for collisions if((*list1)->m_collisionFlag != GameObject::TYPE_NONE){ GameList::iterator list2; for(list2=m_gameObjectList.begin(); list2 != m_gameObjectList.end(); ++list2){ if(!(*list2)->m_active) continue; if(list1 == list2) continue; if( (*list2)->m_active && ((*list1)->m_collisionFlag & (*list2)->m_type) && (*list1)->IsColliding(*list2)){ (*list1)->DoCollision((*list2)); } } } if(list1==m_gameObjectList.end()) break; } GameList::iterator end    = m_gameObjectList.end(); GameList::iterator newEnd = remove_if(m_gameObjectList.begin(),m_gameObjectList.end(),RemoveNotActive); if(newEnd != end)        m_gameObjectList.erase(newEnd,end); } void GameManager::LoadAllFiles(){ LoadSkin(m_gameTextureList, "Models/Skybox/Images/Top.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Models/Skybox/Images/Right.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Models/Skybox/Images/Back.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Models/Skybox/Images/Left.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Models/Skybox/Images/Front.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Models/Skybox/Images/Bottom.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Terrain/Textures/Terrain1.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Terrain/Textures/Terrain2.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Terrain/Details/TerrainDetails.bmp", GetNextFreeID()); LoadSkin(m_gameTextureList, "Terrain/Textures/Water1.bmp", GetNextFreeID()); Block* a = new Block(0, 0, 0, 5); AddGameObject(a); a = new Block(30, 0, 0, 5); AddGameObject(a); Player* d = new Player(0, 100,0); AddGameObject(d); } void Block::Draw(){ glPushMatrix(); glTranslatef(m_position.x(), m_position.y(), m_position.z()); glRotatef(m_facingAngle, 0, 1, 0); glScalef(m_size, m_size, m_size); glBegin(GL_LINES); glColor3f(255, 255, 255); glVertex3f(m_boundingRect.left, m_boundingRect.top, m_position.z()); glVertex3f(m_boundingRect.right, m_boundingRect.top, m_position.z()); glVertex3f(m_boundingRect.left, m_boundingRect.bottom, m_position.z()); glVertex3f(m_boundingRect.right, m_boundingRect.bottom, m_position.z()); glVertex3f(m_boundingRect.left, m_boundingRect.top, m_position.z()); glVertex3f(m_boundingRect.left, m_boundingRect.bottom, m_position.z()); glVertex3f(m_boundingRect.right, m_boundingRect.top, m_position.z()); glVertex3f(m_boundingRect.right, m_boundingRect.bottom, m_position.z()); glEnd(); // DrawBox(m_position.x(), m_position.y(), m_position.z(), m_size, m_size, m_size, 8); glPopMatrix(); } void Block::DoCollision(GameObject* obj){ GameObject* t = this;   // I modified this to see for sure that it was causing the mistake. // obj->DoCollision(NULL); // Just revert it back to /* void Block::DoCollision(GameObject* obj){     obj->DoCollision(this);   }   */ }

  Read the article

• How should I change my Graph structure (very slow insertion)?

  - by Nazgulled

  Hi, This program I'm doing is about a social network, which means there are users and their profiles. The profiles structure is UserProfile. Now, there are various possible Graph implementations and I don't think I'm using the best one. I have a Graph structure and inside, there's a pointer to a linked list of type Vertex. Each Vertex element has a value, a pointer to the next Vertex and a pointer to a linked list of type Edge. Each Edge element has a value (so I can define weights and whatever it's needed), a pointer to the next Edge and a pointer to the Vertex owner. I have a 2 sample files with data to process (in CSV style) and insert into the Graph. The first one is the user data (one user per line); the second one is the user relations (for the graph). The first file is quickly inserted into the graph cause I always insert at the head and there's like ~18000 users. The second file takes ages but I still insert the edges at the head. The file has about ~520000 lines of user relations and takes between 13-15mins to insert into the Graph. I made a quick test and reading the data is pretty quickly, instantaneously really. The problem is in the insertion. This problem exists because I have a Graph implemented with linked lists for the vertices. Every time I need to insert a relation, I need to lookup for 2 vertices, so I can link them together. This is the problem... Doing this for ~520000 relations, takes a while. How should I solve this? Solution 1) Some people recommended me to implement the Graph (the vertices part) as an array instead of a linked list. This way I have direct access to every vertex and the insertion is probably going to drop considerably. But, I don't like the idea of allocating an array with [18000] elements. How practically is this? My sample data has ~18000, but what if I need much less or much more? The linked list approach has that flexibility, I can have whatever size I want as long as there's memory for it. But the array doesn't, how am I going to handle such situation? What are your suggestions? Using linked lists is good for space complexity but bad for time complexity. And using an array is good for time complexity but bad for space complexity. Any thoughts about this solution? Solution 2) This project also demands that I have some sort of data structures that allows quick lookup based on a name index and an ID index. For this I decided to use Hash Tables. My tables are implemented with separate chaining as collision resolution and when a load factor of 0.70 is reach, I normally recreate the table. I base the next table size on this http://planetmath.org/encyclopedia/GoodHashTablePrimes.html. Currently, both Hash Tables hold a pointer to the UserProfile instead of duplication the user profile itself. That would be stupid, changing data would require 3 changes and it's really dumb to do it that way. So I just save the pointer to the UserProfile. The same user profile pointer is also saved as value in each Graph Vertex. So, I have 3 data structures, one Graph and two Hash Tables and every single one of them point to the same exact UserProfile. The Graph structure will serve the purpose of finding the shortest path and stuff like that while the Hash Tables serve as quick index by name and ID. What I'm thinking to solve my Graph problem is to, instead of having the Hash Tables value point to the UserProfile, I point it to the corresponding Vertex. It's still a pointer, no more and no less space is used, I just change what I point to. Like this, I can easily and quickly lookup for each Vertex I need and link them together. This will insert the ~520000 relations pretty quickly. I thought of this solution because I already have the Hash Tables and I need to have them, then, why not take advantage of them for indexing the Graph vertices instead of the user profile? It's basically the same thing, I can still access the UserProfile pretty quickly, just go to the Vertex and then to the UserProfile. But, do you see any cons on this second solution against the first one? Or only pros that overpower the pros and cons on the first solution? Other Solution) If you have any other solution, I'm all ears. But please explain the pros and cons of that solution over the previous 2. I really don't have much time to be wasting with this right now, I need to move on with this project, so, if I'm doing to do such a change, I need to understand exactly what to change and if that's really the way to go. Hopefully no one fell asleep reading this and closed the browser, sorry for the big testament. But I really need to decide what to do about this and I really need to make a change. P.S: When answering my proposed solutions, please enumerate them as I did so I know exactly what are you talking about and don't confuse my self more than I already am.

  Read the article

• 1136: Incorrect number of arguments. Expected 0.? AS3 Flash Cs4 (Round 2)

  - by charmaine

  (I have asked this before but I dont think I was direct enough with my question and therefore it did not get resolved so here goes again!) I am working through a book called Foundation Actionscript 3.0 Animation, making things move. I am now on Chapter 9 - Collision Detection. On two lines of my code I get the 1135 error, letting me know that I have an incorrect number of arguments. I have highlighted the two areas in which this occurs with asterisks: package { import flash.display.Sprite; import flash.events.Event; public class Bubbles extends Sprite { private var balls:Array; private var numBalls:Number = 10; private var centerBall:Ball; private var bounce:Number = -1; private var spring:Number = 0.2; public function Bubbles() { init(); } private function init():void { balls = new Array(); ***centerBall = new Ball(100, 0xcccccc);*** addChild(centerBall); centerBall.x = stage.stageWidth / 2; centerBall.y = stage.stageHeight / 2; for(var i:uint = 0; i < numBalls; i++) { ***var ball:Ball = new Ball(Math.random() * 40 + 5, Math.random() * 0xffffff);*** ball.x = Math.random() * stage.stageWidth; ball.y = Math.random() * stage.stageHeight; ball.vx = Math.random() * 6 - 3; ball.vy = Math.random() * 6 - 3; addChild(ball); balls.push(ball); } addEventListener(Event.ENTER_FRAME, onEnterFrame); } private function onEnterFrame(event:Event):void { for(var i:uint = 0; i < numBalls; i++) { var ball:Ball = balls[i]; move(ball); var dx:Number = ball.x - centerBall.x; var dy:Number = ball.y - centerBall.y; var dist:Number = Math.sqrt(dx * dx + dy * dy); var minDist:Number = ball.radius + centerBall.radius; if(dist < minDist) { var angle:Number = Math.atan2(dy, dx); var tx:Number = centerBall.x + Math.cos(angle) * minDist; var ty:Number = centerBall.y + Math.sin(angle) * minDist; ball.vx += (tx - ball.x) * spring; ball.vy += (ty - ball.y) * spring; } } } private function move(ball:Ball):void { ball.x += ball.vx; ball.y += ball.vy; if(ball.x + ball.radius > stage.stageWidth) { ball.x = stage.stageWidth - ball.radius; ball.vx *= bounce; } else if(ball.x - ball.radius < 0) { ball.x = ball.radius; ball.vx *= bounce; } if(ball.y + ball.radius > stage.stageHeight) { ball.y = stage.stageHeight - ball.radius; ball.vy *= bounce; } else if(ball.y - ball.radius < 0) { ball.y = ball.radius; ball.vy *= bounce; } } } } I think this is due to the non-existance of a Ball.as, when reading the tutorial I assumed it meant that I had to create a movie clip of a ball on stage and then export it for actionscript with the class name being Ball, however when flicking back through the book I saw that a Ball.as already existed, stating that I may need to use this again later on in the book, this read: package { import flash.display.Sprite; public class Ball extends Sprite { private var radius:Number; private var color:uint; public var vx:Number=0; public var vy:Number=0; public function Ball(radius:Number=40, color:uint=0xff0000) { this.radius=radius; this.color=color; init(); } public function init():void { graphics.beginFill(color); graphics.drawCircle(0, 0, radius); graphics.endFill(); } } } This managed to stop all the errors appearing however, it did not transmit any of the effects from Bubbles.as it just braught a Red Ball on the center of the stage. How would I alter this code in order to work in favour of Bubbles.as? Please Help! Thanks!

  Read the article

• Linux e1000e (Intel networking driver) problems galore, where do I start?

  - by Evan Carroll

  I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg: [ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled [ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4 [ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation. [ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64 [ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003 [ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X and, a bunch of [ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 2128.005452] TDH <89> [ 2128.005454] TDT <27> [ 2128.005456] next_to_use <27> [ 2128.005458] next_to_clean <88> [ 2128.005460] buffer_info[next_to_clean]: [ 2128.005463] time_stamp <6e608> [ 2128.005465] next_to_watch <8a> [ 2128.005467] jiffies <6f929> [ 2128.005469] next_to_watch.status <0> [ 2128.005471] MAC Status <80080703> [ 2128.005473] PHY Status <796d> [ 2128.005475] PHY 1000BASE-T Status <4000> [ 2128.005477] PHY Extended Status <3000> [ 2128.005480] PCI Status <10> I decided to compile the latest stable e1000e to 1.2.17, now I'm getting: [ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI [ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64 [ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9906.832056] eth0: no IPv6 routers present With 1.2.20 I get: [ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI [ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64 [ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9722.920014] eth0: no IPv6 routers present But, I'm still getting these [ 9982.992851] PCI Status <10> [ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 9984.993606] TDH <5d> [ 9984.993608] TDT <6b> [ 9984.993611] next_to_use <6b> [ 9984.993613] next_to_clean <5b> [ 9984.993615] buffer_info[next_to_clean]: [ 9984.993617] time_stamp <24da80> [ 9984.993619] next_to_watch <5d> [ 9984.993621] jiffies <24f200> [ 9984.993624] next_to_watch.status <0> [ 9984.993626] MAC Status <80080703> [ 9984.993628] PHY Status <796d> [ 9984.993630] PHY 1000BASE-T Status <4000> [ 9984.993632] PHY Extended Status <3000> [ 9984.993635] PCI Status <10> [ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter [ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO I'm not sure where to start troubleshooting this. Any ideas? Here is the result of ethtool -d eth0 MAC Registers ------------- 0x00000: CTRL (Device control register) 0x18100248 Endian mode (buffers): little Link reset: reset Set link up: 1 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: enabled VLAN mode: disabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x80080703 Duplex: full Link up: link config TBI mode: disabled Link speed: 10Mb/s Bus type: PCI Express Port number: 0 0x00100: RCTL (Receive control register) 0x04048002 Receiver: enabled Store bad packets: disabled Unicast promiscuous: disabled Multicast promiscuous: disabled Long packet: disabled Descriptor minimum threshold size: 1/2 Broadcast accept mode: accept VLAN filter: enabled Canonical form indicator: disabled Discard pause frames: filtered Pass MAC control frames: don't pass Receive buffer size: 2048 0x02808: RDLEN (Receive desc length) 0x00001000 0x02810: RDH (Receive desc head) 0x00000001 0x02818: RDT (Receive desc tail) 0x000000F0 0x02820: RDTR (Receive delay timer) 0x00000000 0x00400: TCTL (Transmit ctrl register) 0x3103F0FA Transmitter: enabled Pad short packets: enabled Software XOFF Transmission: disabled Re-transmit on late collision: enabled 0x03808: TDLEN (Transmit desc length) 0x00001000 0x03810: TDH (Transmit desc head) 0x00000000 0x03818: TDT (Transmit desc tail) 0x00000000 0x03820: TIDV (Transmit delay timer) 0x00000008 PHY type: IGP2 and ethtool -c eth0 Coalesce parameters for eth0: Adaptive RX: off TX: off stats-block-usecs: 0 sample-interval: 0 pkt-rate-low: 0 pkt-rate-high: 0 rx-usecs: 3 rx-frames: 0 rx-usecs-irq: 0 rx-frames-irq: 0 tx-usecs: 0 tx-frames: 0 tx-usecs-irq: 0 tx-frames-irq: 0 rx-usecs-low: 0 rx-frame-low: 0 tx-usecs-low: 0 tx-frame-low: 0 rx-usecs-high: 0 rx-frame-high: 0 tx-usecs-high: 0 tx-frame-high: 0 Here is also the lspci -vvv for this controller 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Lenovo ThinkPad X60s Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 415a Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74 Kernel driver in use: e1000e Kernel modules: e1000e I filed a bug on this upstream, still no idea how to get more useful information. Here is a the result of the running that script EEPROM FIX UPDATE $ sudo bash fixeep-82573-dspd.sh eth0 eth0: is a "82573L Gigabit Ethernet Controller" This fixup is applicable to your hardware Your eeprom is up to date, no changes were made Do I still need to do anything? Also here is my EEPROM dump $ sudo ethtool -e eth0 Offset Values ------ ------ 0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff 0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80 0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27 0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f 0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff 0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00 0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff 0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0 I'd also like to note that I used eth0 every day for years and until recently never had an issue.

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• FreeBSD 8.1 unstable network connection

  - by frankcheong

  I have three FreeBSD 8.1 running on three different hardware and therefore consist of different network adapter as well (bce, bge and igb). I found that the network connection is kind of unstable which I have tried to scp some 10MB file and found that I cannot always get the files completed successfully. I have further checked with my network admin and he claim that the problem is being caused by the network driver which cannot support the load whereby he tried to ping using huge packet size (around 15k) and my server will drop packet consistently at a regular interval. I found that this statement may not be valid since the three server is using three different network drive and it would be quite impossible that the same problem is being caused by three different network adapter and thus different network driver. Since then I have tried to tune up the performance by playing around with the /etc/sysctl.conf figures with no luck. kern.ipc.somaxconn=1024 kern.ipc.shmall=3276800 kern.ipc.shmmax=1638400000 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Required by pf net.inet.ip.forwarding=1 #Network Performance Tuning kern.ipc.maxsockbuf=16777216 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.recvbuf_max=16777216 # Setting specifically for 1 or even 10Gbps network net.local.stream.sendspace=262144 net.local.stream.recvspace=262144 net.inet.tcp.local_slowstart_flightsize=10 net.inet.tcp.nolocaltimewait=1 net.inet.tcp.mssdflt=1460 net.inet.tcp.sendbuf_auto=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.sendspace=262144 net.inet.tcp.recvspace=262144 net.inet.udp.recvspace=262144 kern.ipc.maxsockbuf=16777216 kern.ipc.nmbclusters=32768 net.inet.tcp.delayed_ack=1 net.inet.tcp.delacktime=100 net.inet.tcp.slowstart_flightsize=179 net.inet.tcp.inflight.enable=1 net.inet.tcp.inflight.min=6144 # Reduce the cache size of slow start connection net.inet.tcp.hostcache.expire=1 Our network admin also claim that they see quite a lot of network up and down from their cisco switch log while I cannot find any up down message inside the dmesg. Have further checked the netstat -s but dont have concrete idea. tcp: 133695291 packets sent 39408539 data packets (3358837321 bytes) 61868 data packets (89472844 bytes) retransmitted 24 data packets unnecessarily retransmitted 0 resends initiated by MTU discovery 50756141 ack-only packets (2148 delayed) 0 URG only packets 0 window probe packets 4372385 window update packets 39781869 control packets 134898031 packets received 72339403 acks (for 3357601899 bytes) 190712 duplicate acks 0 acks for unsent data 59339201 packets (3647021974 bytes) received in-sequence 114 completely duplicate packets (135202 bytes) 27 old duplicate packets 0 packets with some dup. data (0 bytes duped) 42090 out-of-order packets (60817889 bytes) 0 packets (0 bytes) of data after window 0 window probes 3953896 window update packets 64181 packets received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 45192 discarded due to memory problems 19945391 connection requests 1323420 connection accepts 0 bad connection attempts 0 listen queue overflows 0 ignored RSTs in the windows 21133581 connections established (including accepts) 21268724 connections closed (including 32737 drops) 207874 connections updated cached RTT on close 207874 connections updated cached RTT variance on close 132439 connections updated cached ssthresh on close 42392 embryonic connections dropped 72339338 segments updated rtt (of 69477829 attempts) 390871 retransmit timeouts 0 connections dropped by rexmit timeout 0 persist timeouts 0 connections dropped by persist timeout 0 Connections (fin_wait_2) dropped because of timeout 13990 keepalive timeouts 2 keepalive probes sent 13988 connections dropped by keepalive 173044 correct ACK header predictions 36947371 correct data packet header predictions 1323420 syncache entries added 0 retransmitted 0 dupsyn 0 dropped 1323420 completed 0 bucket overflow 0 cache overflow 0 reset 0 stale 0 aborted 0 badack 0 unreach 0 zone failures 1323420 cookies sent 0 cookies received 1864 SACK recovery episodes 18005 segment rexmits in SACK recovery episodes 26066896 byte rexmits in SACK recovery episodes 147327 SACK options (SACK blocks) received 87473 SACK options (SACK blocks) sent 0 SACK scoreboard overflow 0 packets with ECN CE bit set 0 packets with ECN ECT(0) bit set 0 packets with ECN ECT(1) bit set 0 successful ECN handshakes 0 times ECN reduced the congestion window udp: 5141258 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 1 with no checksum 0 dropped due to no socket 129616 broadcast/multicast datagrams undelivered 0 dropped due to full socket buffers 0 not for hashed pcb 5011642 delivered 5016050 datagrams output 0 times multicast source filter matched sctp: 0 input packets 0 datagrams 0 packets that had data 0 input SACK chunks 0 input DATA chunks 0 duplicate DATA chunks 0 input HB chunks 0 HB-ACK chunks 0 input ECNE chunks 0 input AUTH chunks 0 chunks missing AUTH 0 invalid HMAC ids received 0 invalid secret ids received 0 auth failed 0 fast path receives all one chunk 0 fast path multi-part data 0 output packets 0 output SACKs 0 output DATA chunks 0 retransmitted DATA chunks 0 fast retransmitted DATA chunks 0 FR's that happened more than once to same chunk 0 intput HB chunks 0 output ECNE chunks 0 output AUTH chunks 0 ip_output error counter Packet drop statistics: 0 from middle box 0 from end host 0 with data 0 non-data, non-endhost 0 non-endhost, bandwidth rep only 0 not enough for chunk header 0 not enough data to confirm 0 where process_chunk_drop said break 0 failed to find TSN 0 attempt reverse TSN lookup 0 e-host confirms zero-rwnd 0 midbox confirms no space 0 data did not match TSN 0 TSN's marked for Fast Retran Timeouts: 0 iterator timers fired 0 T3 data time outs 0 window probe (T3) timers fired 0 INIT timers fired 0 sack timers fired 0 shutdown timers fired 0 heartbeat timers fired 0 a cookie timeout fired 0 an endpoint changed its cookiesecret 0 PMTU timers fired 0 shutdown ack timers fired 0 shutdown guard timers fired 0 stream reset timers fired 0 early FR timers fired 0 an asconf timer fired 0 auto close timer fired 0 asoc free timers expired 0 inp free timers expired 0 packet shorter than header 0 checksum error 0 no endpoint for port 0 bad v-tag 0 bad SID 0 no memory 0 number of multiple FR in a RTT window 0 RFC813 allowed sending 0 RFC813 does not allow sending 0 times max burst prohibited sending 0 look ahead tells us no memory in interface 0 numbers of window probes sent 0 times an output error to clamp down on next user send 0 times sctp_senderrors were caused from a user 0 number of in data drops due to chunk limit reached 0 number of in data drops due to rwnd limit reached 0 times a ECN reduced the cwnd 0 used express lookup via vtag 0 collision in express lookup 0 times the sender ran dry of user data on primary 0 same for above 0 sacks the slow way 0 window update only sacks sent 0 sends with sinfo_flags !=0 0 unordered sends 0 sends with EOF flag set 0 sends with ABORT flag set 0 times protocol drain called 0 times we did a protocol drain 0 times recv was called with peek 0 cached chunks used 0 cached stream oq's used 0 unread messages abandonded by close 0 send burst avoidance, already max burst inflight to net 0 send cwnd full avoidance, already max burst inflight to net 0 number of map array over-runs via fwd-tsn's ip: 137814085 total packets received 0 bad header checksums 0 with size smaller than minimum 0 with data size < data length 0 with ip length > max ip packet size 0 with header length < data size 0 with data length < header length 0 with bad options 0 with incorrect version number 1200 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 300 packets reassembled ok 137813009 packets for this host 530 packets for unknown/unsupported protocol 0 packets forwarded (0 packets fast forwarded) 61 packets not forwardable 0 packets received for unknown multicast group 0 redirects sent 137234598 packets sent from this host 0 packets sent with fabricated ip header 685307 output packets dropped due to no bufs, etc. 52 output packets discarded due to no route 300 output datagrams fragmented 1200 fragments created 0 datagrams that can't be fragmented 0 tunneling packets that can't find gif 0 datagrams with bad address in header icmp: 0 calls to icmp_error 0 errors not generated in response to an icmp message Output histogram: echo reply: 305 0 messages with bad code fields 0 messages less than the minimum length 0 messages with bad checksum 0 messages with bad length 0 multicast echo requests ignored 0 multicast timestamp requests ignored Input histogram: destination unreachable: 530 echo: 305 305 message responses generated 0 invalid return addresses 0 no return routes ICMP address mask responses are disabled igmp: 0 messages received 0 messages received with too few bytes 0 messages received with wrong TTL 0 messages received with bad checksum 0 V1/V2 membership queries received 0 V3 membership queries received 0 membership queries received with invalid field(s) 0 general queries received 0 group queries received 0 group-source queries received 0 group-source queries dropped 0 membership reports received 0 membership reports received with invalid field(s) 0 membership reports received for groups to which we belong 0 V3 reports received without Router Alert 0 membership reports sent arp: 376748 ARP requests sent 3207 ARP replies sent 245245 ARP requests received 80845 ARP replies received 326090 ARP packets received 267712 total packets dropped due to no ARP entry 108876 ARP entrys timed out 0 Duplicate IPs seen ip6: 2226633 total packets received 0 with size smaller than minimum 0 with data size < data length 0 with bad options 0 with incorrect version number 0 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 0 fragments that exceeded limit 0 packets reassembled ok 2226633 packets for this host 0 packets forwarded 0 packets not forwardable 0 redirects sent 2226633 packets sent from this host 0 packets sent with fabricated ip header 0 output packets dropped due to no bufs, etc. 8 output packets discarded due to no route 0 output datagrams fragmented 0 fragments created 0 datagrams that can't be fragmented 0 packets that violated scope rules 0 multicast packets which we don't join Input histogram: UDP: 2226633 Mbuf statistics: 962679 one mbuf 1263954 one ext mbuf 0 two or more ext mbuf 0 packets whose headers are not continuous 0 tunneling packets that can't find gif 0 packets discarded because of too many headers 0 failures of source address selection Source addresses selection rule applied: icmp6: 0 calls to icmp6_error 0 errors not generated in response to an icmp6 message 0 errors not generated because of rate limitation 0 messages with bad code fields 0 messages < minimum length 0 bad checksums 0 messages with bad length Histogram of error messages to be generated: 0 no route 0 administratively prohibited 0 beyond scope 0 address unreachable 0 port unreachable 0 packet too big 0 time exceed transit 0 time exceed reassembly 0 erroneous header field 0 unrecognized next header 0 unrecognized option 0 redirect 0 unknown 0 message responses generated 0 messages with too many ND options 0 messages with bad ND options 0 bad neighbor solicitation messages 0 bad neighbor advertisement messages 0 bad router solicitation messages 0 bad router advertisement messages 0 bad redirect messages 0 path MTU changes rip6: 0 messages received 0 checksum calculations on inbound 0 messages with bad checksum 0 messages dropped due to no socket 0 multicast messages dropped due to no socket 0 messages dropped due to full socket buffers 0 delivered 0 datagrams output netstat -m 516/5124/5640 mbufs in use (current/cache/total) 512/1634/2146/32768 mbuf clusters in use (current/cache/total/max) 512/1536 mbuf+clusters out of packet secondary zone in use (current/cache) 0/1303/1303/12800 4k (page size) jumbo clusters in use (current/cache/total/max) 0/0/0/6400 9k jumbo clusters in use (current/cache/total/max) 0/0/0/3200 16k jumbo clusters in use (current/cache/total/max) 1153K/9761K/10914K bytes allocated to network (current/cache/total) 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters) 0/0/0 requests for jumbo clusters denied (4k/9k/16k) 0/8/6656 sfbufs in use (current/peak/max) 0 requests for sfbufs denied 0 requests for sfbufs delayed 0 requests for I/O initiated by sendfile 0 calls to protocol drain routines Anyone got an idea what might be the possible cause?

  Read the article

• Automating Solaris 11 Zones Installation Using The Automated Install Server

  - by Orgad Kimchi

  Introduction How to use the Oracle Solaris 11 Automated install server in order to automate the Solaris 11 Zones installation. In this document I will demonstrate how to setup the Automated Install server in order to provide hands off installation process for the Global Zone and two Non Global Zones located on the same system. Architecture layout: Figure 1. Architecture layout Prerequisite Setup the Automated install server (AI) using the following instructions “How to Set Up Automated Installation Services for Oracle Solaris 11” The first step in this setup will be creating two Solaris 11 Zones configuration files. Step 1: Create the Solaris 11 Zones configuration files  The Solaris Zones configuration files should be in the format of the zonecfg export command. # zonecfg -z zone1 export > /var/tmp/zone1# cat /var/tmp/zone1 create -b set brand=solaris set zonepath=/rpool/zones/zone1 set autoboot=true set ip-type=exclusive add anet set linkname=net0 set lower-link=auto set configure-allowed-address=true set link-protection=mac-nospoof set mac-address=random end  Create a backup copy of this file under a different name, for example, zone2. # cp /var/tmp/zone1 /var/tmp/zone2 Modify the second configuration file with the zone2 configuration information You should change the zonepath for example: set zonepath=/rpool/zones/zone2 Step2: Copy and share the Zones configuration files  Create the NFS directory for the Zones configuration files # mkdir /export/zone_config Share the directory for the Zones configuration file # share –o ro /export/zone_config Copy the Zones configuration files into the NFS shared directory # cp /var/tmp/zone1 /var/tmp/zone2  /export/zone_config Verify that the NFS share has been created using the following command # share export_zone_config      /export/zone_config     nfs     sec=sys,ro Step 3: Add the Global Zone as client to the Install Service Use the installadm create-client command to associate client (Global Zone) with the install service To find the MAC address of a system, use the dladm command as described in the dladm(1M) man page. The following command adds the client (Global Zone) with MAC address 0:14:4f:2:a:19 to the s11x86service install service. # installadm create-client -e “0:14:4f:2:a:19" -n s11x86service You can verify the client creation using the following command # installadm list –c Service Name  Client Address     Arch   Image Path ------------  --------------     ----   ---------- s11x86service 00:14:4F:02:0A:19  i386   /export/auto_install/s11x86service We can see the client install service name (s11x86service), MAC address (00:14:4F:02:0A:19 and Architecture (i386). Step 4: Global Zone manifest setup  First, get a list of the installation services and the manifests associated with them: # installadm list -m Service Name   Manifest        Status ------------   --------        ------ default-i386   orig_default   Default s11x86service  orig_default   Default Then probe the s11x86service and the default manifest associated with it. The -m switch reflects the name of the manifest associated with a service. Since we want to capture that output into a file, we redirect the output of the command as follows: # installadm export -n s11x86service -m orig_default >  /var/tmp/orig_default.xml Create a backup copy of this file under a different name, for example, orig-default2.xml, and edit the copy. # cp /var/tmp/orig_default.xml /var/tmp/orig_default2.xml Use the configuration element in the AI manifest for the client system to specify non-global zones. Use the name attribute of the configuration element to specify the name of the zone. Use the source attribute to specify the location of the config file for the zone.The source location can be any http:// or file:// location that the client can access during installation. The following sample AI manifest specifies two Non-Global Zones: zone1 and zone2 You should replace the server_ip with the ip address of the NFS server. <!DOCTYPE auto_install SYSTEM "file:///usr/share/install/ai.dtd.1"> <auto_install>   <ai_instance>     <target>       <logical>         <zpool name="rpool" is_root="true">           <filesystem name="export" mountpoint="/export"/>           <filesystem name="export/home"/>           <be name="solaris"/>         </zpool>       </logical>     </target>     <software type="IPS">       <source>         <publisher name="solaris">           <origin name="http://pkg.oracle.com/solaris/release"/>         </publisher>       </source>       <software_data action="install">         <name>pkg:/entire@latest</name>         <name>pkg:/group/system/solaris-large-server</name>       </software_data>     </software>     <configuration type="zone" name="zone1" source="file:///net/server_ip/export/zone_config/zone1"/>     <configuration type="zone" name="zone2" source="file:///net/server_ip/export/zone_config/zone2"/>   </ai_instance> </auto_install> The following example adds the /var/tmp/orig_default2.xml AI manifest to the s11x86service install service # installadm create-manifest -n s11x86service -f /var/tmp/orig_default2.xml -m gzmanifest You can verify the manifest creation using the following command # installadm list -n s11x86service  -m Service/Manifest Name  Status   Criteria ---------------------  ------   -------- s11x86service    orig_default        Default  None    gzmanifest          Inactive None We can see from the command output that the new manifest named gzmanifest has been created and associated with the s11x86service install service. Step 5: Non Global Zone manifest setup The AI manifest for non-global zone installation is similar to the AI manifest for installing the global zone. If you do not provide a custom AI manifest for a non-global zone, the default AI manifest for Zones is used The default AI manifest for Zones is available at /usr/share/auto_install/manifest/zone_default.xml. In this example we should use the default AI manifest for zones The following sample default AI manifest for zones # cat /usr/share/auto_install/manifest/zone_default.xml <?xml version="1.0" encoding="UTF-8"?> <!--  Copyright (c) 2011, 2012, Oracle and/or its affiliates. All rights reserved. --> <!DOCTYPE auto_install SYSTEM "file:///usr/share/install/ai.dtd.1"> <auto_install>     <ai_instance name="zone_default">         <target>             <logical>                 <zpool name="rpool">                     <!--                       Subsequent <filesystem> entries instruct an installer                       to create following ZFS datasets:                           <root_pool>/export         (mounted on /export)                           <root_pool>/export/home    (mounted on /export/home)                       Those datasets are part of standard environment                       and should be always created.                       In rare cases, if there is a need to deploy a zone                       without these datasets, either comment out or remove                       <filesystem> entries. In such scenario, it has to be also                       assured that in case of non-interactive post-install                       configuration, creation of initial user account is                       disabled in related system configuration profile.                       Otherwise the installed zone would fail to boot.                     -->                     <filesystem name="export" mountpoint="/export"/>                     <filesystem name="export/home"/>                     <be name="solaris">                         <options>                             <option name="compression" value="on"/>                         </options>                     </be>                 </zpool>             </logical>         </target>         <software type="IPS">             <destination>                 <image>                     <!-- Specify locales to install -->                     <facet set="false">facet.locale.*</facet>                     <facet set="true">facet.locale.de</facet>                     <facet set="true">facet.locale.de_DE</facet>                     <facet set="true">facet.locale.en</facet>                     <facet set="true">facet.locale.en_US</facet>                     <facet set="true">facet.locale.es</facet>                     <facet set="true">facet.locale.es_ES</facet>                     <facet set="true">facet.locale.fr</facet>                     <facet set="true">facet.locale.fr_FR</facet>                     <facet set="true">facet.locale.it</facet>                     <facet set="true">facet.locale.it_IT</facet>                     <facet set="true">facet.locale.ja</facet>                     <facet set="true">facet.locale.ja_*</facet>                     <facet set="true">facet.locale.ko</facet>                     <facet set="true">facet.locale.ko_*</facet>                     <facet set="true">facet.locale.pt</facet>                     <facet set="true">facet.locale.pt_BR</facet>                     <facet set="true">facet.locale.zh</facet>                     <facet set="true">facet.locale.zh_CN</facet>                     <facet set="true">facet.locale.zh_TW</facet>                 </image>             </destination>             <software_data action="install">                 <name>pkg:/group/system/solaris-small-server</name>             </software_data>         </software>     </ai_instance> </auto_install> (optional) We can customize the default AI manifest for Zones Create a backup copy of this file under a different name, for example, zone_default2.xml and edit the copy # cp /usr/share/auto_install/manifest/zone_default.xml /var/tmp/zone_default2.xml Edit the copy (/var/tmp/zone_default2.xml) The following example adds the /var/tmp/zone_default2.xml AI manifest to the s11x86service install service and specifies that zone1 and zone2 should use this manifest. # installadm create-manifest -n s11x86service -f /var/tmp/zone_default2.xml -m zones_manifest -c zonename="zone1 zone2" Note: Do not use the following elements or attributes in a non-global zone AI manifest:     The auto_reboot attribute of the ai_instance element     The http_proxy attribute of the ai_instance element     The disk child element of the target element     The noswap attribute of the logical element     The nodump attribute of the logical element     The configuration element Step 6: Global Zone profile setup We are going to create a global zone configuration profile which includes the host information for example: host name, ip address name services etc… # sysconfig create-profile –o /var/tmp/gz_profile.xml You need to provide the host information for example:     Default router     Root password     DNS information The output should eventually disappear and be replaced by the initial screen of the System Configuration Tool (see Figure 2), where you can do the final configuration. Figure 2. Profile creation menu You can validate the profile using the following command # installadm validate -n s11x86service –P /var/tmp/gz_profile.xml Validating static profile gz_profile.xml...  Passed Next, instantiate a profile with the install service. In our case, use the following syntax for doing this # installadm create-profile -n s11x86service  -f /var/tmp/gz_profile.xml -p  gz_profile You can verify profile creation using the following command # installadm list –n s11x86service  -p Service/Profile Name  Criteria --------------------  -------- s11x86service    gz_profile         None We can see that the gz_profie has been created and associated with the s11x86service Install service. Step 7: Setup the Solaris Zones configuration profiles The step should be similar to the Global zone profile creation on step 6 # sysconfig create-profile –o /var/tmp/zone1_profile.xml # sysconfig create-profile –o /var/tmp/zone2_profile.xml You can validate the profiles using the following command # installadm validate -n s11x86service -P /var/tmp/zone1_profile.xml Validating static profile zone1_profile.xml...  Passed # installadm validate -n s11x86service -P /var/tmp/zone2_profile.xml Validating static profile zone2_profile.xml...  Passed Next, associate the profiles with the install service The following example adds the zone1_profile.xml configuration profile to the s11x86service  install service and specifies that zone1 should use this profile. # installadm create-profile -n s11x86service  -f  /var/tmp/zone1_profile.xml -p zone1_profile -c zonename=zone1 The following example adds the zone2_profile.xml configuration profile to the s11x86service  install service and specifies that zone2 should use this profile. # installadm create-profile -n s11x86service  -f  /var/tmp/zone2_profile.xml -p zone2_profile -c zonename=zone2 You can verify the profiles creation using the following command # installadm list -n s11x86service -p Service/Profile Name  Criteria --------------------  -------- s11x86service    zone1_profile      zonename = zone1    zone2_profile      zonename = zone2    gz_profile         None We can see that we have three profiles in the s11x86service  install service     Global Zone  gz_profile     zone1            zone1_profile     zone2            zone2_profile. Step 8: Global Zone setup Associate the global zone client with the manifest and the profile that we create in the previous steps The following example adds the manifest and profile to the client (global zone), where: gzmanifest  is the name of the manifest. gz_profile  is the name of the configuration profile. mac="0:14:4f:2:a:19" is the client (global zone) mac address s11x86service is the install service name. # installadm set-criteria -m  gzmanifest  –p  gz_profile  -c mac="0:14:4f:2:a:19" -n s11x86service You can verify the manifest and profile association using the following command # installadm list -n s11x86service -p  -m Service/Manifest Name  Status   Criteria ---------------------  ------   -------- s11x86service    gzmanifest                   mac  = 00:14:4F:02:0A:19    orig_default        Default  None Service/Profile Name  Criteria --------------------  -------- s11x86service    gz_profile         mac      = 00:14:4F:02:0A:19    zone2_profile      zonename = zone2    zone1_profile      zonename = zone1 Step 9: Provision the host with the Non-Global Zones The next step is to boot the client system off the network and provision it using the Automated Install service that we just set up. First, boot the client system. Figure 3 shows the network boot attempt (when done on an x86 system): Figure 3. Network Boot Then you will be prompted by a GRUB menu, with a timer, as shown in Figure 4. The default selection (the "Text Installer and command line" option) is highlighted.  Press the down arrow to highlight the second option labeled Automated Install, and then press Enter. The reason we need to do this is because we want to prevent a system from being automatically re-installed if it were to be booted from the network accidentally. Figure 4. GRUB Menu What follows is the continuation of a networked boot from the Automated Install server,. The client downloads a mini-root (a small set of files in which to successfully run the installer), identifies the location of the Automated Install manifest on the network, retrieves that manifest, and then processes it to identify the address of the IPS repository from which to obtain the desired software payload. Non-Global Zones are installed and configured on the first reboot after the Global Zone is installed. You can list all the Solaris Zones status using the following command # zoneadm list -civ Once the Zones are in running state you can login into the Zone using the following command # zlogin –z zone1 Troubleshooting Automated Installations If an installation to a client system failed, you can find the client log at /system/volatile/install_log. NOTE: Zones are not installed if any of the following errors occurs:     A zone config file is not syntactically correct.     A collision exists among zone names, zone paths, or delegated ZFS datasets in the set of zones to be installed     Required datasets are not configured in the global zone. For more troubleshooting information see “Installing Oracle Solaris 11 Systems” Conclusion This paper demonstrated the benefits of using the Automated Install server to simplify the Non Global Zones setup, including the creation and configuration of the global zone manifest and the Solaris Zones profiles.

  Read the article

• Getting problem in threading in JAVA

  - by chetans

  In this program i want to stop GenerateImage & MovingImage Thread both... And i want to start those threads from begining. Can u send me the solution? Here is the code........ package Game; import java.applet.Applet; import java.awt.Color; import java.awt.Dimension; import java.awt.Graphics; import java.awt.Image; import java.awt.MediaTracker; import java.awt.event.KeyEvent; import java.awt.event.KeyListener; import java.net.MalformedURLException; import java.net.URL; public class ThreadInApplet extends Applet implements KeyListener { private static final long serialVersionUID = 1L; Image[] asteroidImage; Image spaceshipImage; String levelstr="Easy Level"; int[] XPos,YPos; int number=0,XPosOfSpaceship,YPosOfSpaceship,NoOfObstacles=5,speed=1,level=1,spaceBtnPressdCntr=0; boolean gameStart=false,pauseGame=false,collideUp=false,collideDown=false,collideLeft=false,collideRight=false; private Image offScreenImage; private Dimension offScreenSize; private Graphics offScreenGraphics; Thread GenerateImages,MoveImages; public void init() { try { GenerateImages=new Thread () //thread to create obstacles { synchronized public void run () { for(int g=0;g<NoOfObstacles;g++) { try { sleep(1000); } catch (InterruptedException e) { e.printStackTrace(); } number++; // Temporary counter to count the no of obstacles created } } } ; MoveImages=new Thread () //thread to move obstacles { @SuppressWarnings("deprecation") synchronized public void run () { while(YPos[NoOfObstacles-1]!=600) { pauseGame=false; if(collide()==true) { GenerateImages.suspend(); repaint(); } else GenerateImages.resume(); for(int l=0;l<number;l++) { if(collide()==false) YPos[l]++; else GenerateImages.suspend(); } repaint(); try { sleep(speed); } catch (InterruptedException e) { e.printStackTrace(); } } if(YPos[NoOfObstacles-1]>=600) //level complete state { level++; try { levelUpdation(level); System.out.println("aahe"); } catch (MalformedURLException e) { e.printStackTrace(); } repaint(); } } }; initialPos(); spaceshipImage=getImage(new URL(getCodeBase(),"images/space.png")); for(int i=0;i<NoOfObstacles;i++) { asteroidImage[i]=getImage(new URL(getCodeBase(),"images/asteroid.png")); XPos[i]=(int) (Math.random()*700); YPos[i]=0; } MediaTracker tracker = new MediaTracker (this); for(int i=0;i<NoOfObstacles;i++) { tracker.addImage (asteroidImage[i], 0); } } catch (MalformedURLException e) { e.printStackTrace(); } setBackground(Color.black); addKeyListener(this); } //Sets initial positions of spaceship & obstacle images------------------------------------------------------ public void initialPos() throws MalformedURLException { asteroidImage=new Image[NoOfObstacles]; XPos=new int[NoOfObstacles]; YPos=new int[NoOfObstacles]; XPosOfSpaceship=getWidth()/2-35; YPosOfSpaceship=getHeight()-100; collideUp = false; collideDown=false; collideLeft=false; collideRight=false; } //level finished updations------------------------------------------------------------------------------ @SuppressWarnings("deprecation") public void levelUpdation(int level) throws MalformedURLException { NoOfObstacles=NoOfObstacles+20; speed=speed-3; System.out.println(NoOfObstacles+" "+speed); pauseGame=true; initialPos(); repaint(); } //paint method of graphics to print the messages--------------------------------------------------------- public void paint(Graphics g) { g.setColor(Color.white); if(gameStart==false) { g.drawString("SPACE to start", (getWidth()/2)-15, getHeight()/2); g.drawString(levelstr, (getWidth()/2), getHeight()/2+20); } if(level>1) { if(level==2) levelstr="Medium Level"; else levelstr="High Level"; g.drawString("Level Complete ", (getWidth()/2)-15, getHeight()/2); g.drawString(levelstr, (getWidth()/2), getHeight()/2+20); //g.drawString("SPACE to start", (getWidth()/2)-15, getHeight()/2+40); } for(int n=0;n<number;n++) { if(n>0) g.drawImage(asteroidImage[n],XPos[n],YPos[n],this); } g.drawImage(spaceshipImage,XPosOfSpaceship,YPosOfSpaceship,this); } //update method of graphics to print the messages--------------------------------------------------------- @SuppressWarnings("deprecation") public void update(Graphics g) { Dimension d = size(); if((offScreenImage == null) || (d.width != offScreenSize.width) || (d.height != offScreenSize.height)) { offScreenImage = createImage(d.width, d.height); offScreenSize = d; offScreenGraphics = offScreenImage.getGraphics(); } offScreenGraphics.clearRect(0, 0, d.width, d.height); paint(offScreenGraphics); g.drawImage(offScreenImage, 0, 0, null); } public void keyReleased(KeyEvent arg0){} public void keyTyped(KeyEvent arg0) {} //---------------------Key pressed event to start game & to move the spaceship-------------------------------------- public void keyPressed(KeyEvent e) { if(e.getKeyCode()==32) { spaceBtnPressdCntr++; if(spaceBtnPressdCntr==1) { gameStart=true; GenerateImages.start(); MoveImages.start(); } } if(gameStart==true) { if(e.getKeyCode()==37) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideLeft == true) { GenerateImages.suspend(); } else { if(XPosOfSpaceship>0) XPosOfSpaceship--; } } repaint(); } }.start(); } if(e.getKeyCode()==38) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideUp == true) { GenerateImages.suspend(); } else { if(YPosOfSpaceship>10) YPosOfSpaceship--; } } repaint(); } }.start(); } if(e.getKeyCode()==39) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideRight == true) { GenerateImages.suspend(); } else { if(XPosOfSpaceship<750) XPosOfSpaceship++; } } repaint(); } }.start(); } if(e.getKeyCode()==40) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideDown == true) { GenerateImages.suspend(); } else { if(YPosOfSpaceship<550) YPosOfSpaceship++; } } repaint(); } }.start(); } } } //------------------------------Collision checking between Spaceship & obstacles------------------------------ public boolean collide() { int x1,y1,x2,y2,x3,y3,x4,y4; //coordinates of obstacles int a1,b1,a2,b2,a3,b3,a4,b4; //coordinates of spaceship a1 =XPosOfSpaceship; b1=YPosOfSpaceship; a2=a1+spaceshipImage.getWidth(this); b2=b1; a3=a1; b3=b1+spaceshipImage.getHeight(this); a4=a2; b4=b3; for(int a=0;a<number;a++) { x1 =XPos[a]; y1=YPos[a]; x2=x1+asteroidImage[a].getWidth(this); y2=y1; x3=x1; y3=y1+asteroidImage[a].getHeight(this); x4=x2; y4=y3; /********checking asteroid touch spaceship from up direction********/ if(y3==b1 && x4>=a1 && x4<=a2) { collideUp = true; collideDown=false; collideLeft=false; collideRight=false; return(true); } if(y3==b1 && x3>=a1 && x3<=a2) { collideUp = true; collideDown=false; collideLeft=false; collideRight=false; return(true); } /********checking asteroid touch spaceship from left direction******/ if(x2==a1 && y4>=b1 && y4<=b3) { collideLeft=true; collideUp = false; collideDown=false; collideRight=false; return(true); } if(x2==a1 && y2>=b1 && y2<=b3) { collideLeft=true; collideUp = false; collideDown=false; collideRight=false; return(true); } /********checking asteroid touch spaceship from right direction*****/ if(x1==a2 && y3>=b2 && y3<=b4) { collideRight=true; collideLeft=false; collideUp = false; collideDown=false; return(true); } if(x1==a2 && y1>=b2 && y1<=b4) { collideRight=true; collideLeft=false; collideUp = false; collideDown=false; return(true); } /********checking asteroid touch spaceship from down direction*****/ if(y1==b3 && x2>=a3 && x2<=a4) { collideDown=true; collideRight=false; collideLeft=false; collideUp = false; return(true); } if(y1==b3 && x1>=a3 && x1<=a4) { collideDown=true; collideRight=false; collideLeft=false; collideUp = false; return(true); } } return(false); } }

  Read the article

• Thread not behaving correctly

  - by ivor

  Hello, I wonder if anyone can help me to understand where I could be going wrong with this code; Basically I'm working on a turorial and calling the class below from another class - and it is getting the following error; Exception in thread "Thread-1" java.lang.NullPointerException at org.newdawn.spaceinvaders.TCPChat.run(TCPChat.java:322) at java.lang.Thread.run(Unknown Source) I realise the error is beibg flagged in another class- but I have tested the other class with a small class which sets up a separate thread - and it works fine, but as soon as I try and implement a new thread in this class - it causes all sorts of problems. Am I setting up the thread correctly in this class? Basically I can set up a thread in this class, with a test loop and it's fine, but when I bring in the functionality of the rest of the game it sometimes hangs, or does not display at all. Any suggestions on where I could be going wrong would be greatly appreciated. Thanks for looking. package org.newdawn.spaceinvaders; import java.awt.BorderLayout; import java.awt.Canvas; import java.awt.Color; import java.awt.Dimension; import java.awt.FlowLayout; import java.awt.Graphics2D; import java.awt.GridLayout; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.awt.event.KeyAdapter; import java.awt.event.KeyEvent; import java.awt.event.WindowAdapter; import java.awt.event.WindowEvent; import java.awt.image.BufferStrategy; import java.util.ArrayList; import java.util.Scanner; import java.awt.*;//maybe not needed import javax.swing.*;//maybenot needed import java.util.Random; //import java.io.*; /** * The main hook of our game. This class with both act as a manager * for the display and central mediator for the game logic. * * Display management will consist of a loop that cycles round all * entities in the game asking them to move and then drawing them * in the appropriate place. With the help of an inner class it * will also allow the player to control the main ship. * * As a mediator it will be informed when entities within our game * detect events (e.g. alient killed, played died) and will take * appropriate game actions. * * @author Kevin Glass */ public class Game extends Canvas implements Runnable{ /** The stragey that allows us to use accelerate page flipping */ private BufferStrategy strategy; /** True if the game is currently "running", i.e. the game loop is looping */ private boolean gameRunning = true; /** The list of all the entities that exist in our game */ private ArrayList entities = new ArrayList(); /** The list of entities that need to be removed from the game this loop */ private ArrayList removeList = new ArrayList(); /** The entity representing the player */ private Entity ship; /** The speed at which the player's ship should move (pixels/sec) */ private double moveSpeed = 300; /** The time at which last fired a shot */ private long lastFire = 0; /** The interval between our players shot (ms) */ private long firingInterval = 500; /** The number of aliens left on the screen */ private int alienCount; /** The number of levels progressed */ private double levelCount; /** high score for the user */ private int highScore; /** high score for the user */ private String player = "bob"; //private GetUserInput getPlayer; /** The list of entities that need to be removed from the game this loop */ /** The message to display which waiting for a key press */ private String message = ""; /** True if we're holding up game play until a key has been pressed */ private boolean waitingForKeyPress = true; /** True if the left cursor key is currently pressed */ private boolean leftPressed = false; /** True if the right cursor key is currently pressed */ private boolean rightPressed = false; /** True if we are firing */ private boolean firePressed = false; /** True if game logic needs to be applied this loop, normally as a result of a game event */ private boolean logicRequiredThisLoop = false; //private Thread cThread = new Thread(this); //public Thread t = new Thread(this); //private Thread g = new Thread(this); void setHighscore(int setHS) { highScore = setHS; } public int getHighscore() { return highScore; } public void setPlayer(String setPlayer) { player = setPlayer; } public String getPlayer() { return player; } public void run() { //setup(); System.out.println("hello im running bob"); /*int count = 1; do { System.out.println("Count is: " + count); count++; try{Thread.sleep(1);} catch(InterruptedException e){} } while (count <= 2000000);*/ //Game g =new Game(); //Game g = this; // Start the main game loop, note: this method will not // return until the game has finished running. Hence we are // using the actual main thread to run the game. //setup(); //this.gameLoop(); //try{thread.sleep(1);} //catch{InterruptedException e} } /** * Construct our game and set it running. */ public Game () { //Thread t = new Thread(this);//set up new thread for invaders game //t.run();//run the run method of the game //Game g =new Game(); //setup(); //Thread t = new Thread(this); //thread.start(); //SwingUtilities.invokeLater(this); Thread er = new Thread(this); er.start(); } public void setup(){ //initialise highscore setHighscore(0); // create a frame to contain our game JFrame container = new JFrame("Space Invaders 101"); // get hold the content of the frame and set up the resolution of the game JPanel panel = (JPanel) container.getContentPane(); panel.setPreferredSize(new Dimension(800,600)); //panel.setLayout(null); // setup our canvas size and put it into the content of the frame setBounds(0,0,800,600); panel.add(this); // Tell AWT not to bother repainting our canvas since we're // going to do that our self in accelerated mode setIgnoreRepaint(true); // finally make the window visible container.pack(); container.setResizable(false); container.setVisible(true); // add a listener to respond to the user closing the window. If they // do we'd like to exit the game container.addWindowListener(new WindowAdapter() { public void windowClosing(WindowEvent e) { //cThread.interrupt(); System.exit(0); } }); // add a key input system (defined below) to our canvas // so we can respond to key pressed addKeyListener(new KeyInputHandler()); // request the focus so key events come to us requestFocus(); // create the buffering strategy which will allow AWT // to manage our accelerated graphics createBufferStrategy(2); strategy = getBufferStrategy(); // initialise the entities in our game so there's something // to see at startup initEntities(); } /** * Start a fresh game, this should clear out any old data and * create a new set. */ private void startGame() { // clear out any existing entities and intialise a new set entities.clear(); initEntities(); //initialise highscore setHighscore(0); // blank out any keyboard settings we might currently have leftPressed = false; rightPressed = false; firePressed = false; } /** * Initialise the starting state of the entities (ship and aliens). Each * entitiy will be added to the overall list of entities in the game. */ //private void initEntities() { public void initEntities() { Random randomAlien = new Random(); // create the player ship and place it roughly in the center of the screen //ship = new ShipEntity(this,"sprites/ship.gif",370,550);//orignal ship = new ShipEntity(this,"sprites/ship.gif",700,300);//changed postioning to right hand side entities.add(ship); // create a block of aliens (5 rows, by 12 aliens, spaced evenly) alienCount = 0; levelCount = 1.02; for (int row=0;row<7;row++) {//altered number of rows for (int x=0;x<5;x++) { int r = randomAlien.nextInt(100);//loop added to produce random aliens if (r < 50){ //Entity alien = new AlienEntity(this,"sprites/alien.gif",/*100+*/(x*50),(50)+row*30); Entity alien = new AlienEntity(this,"sprites/alien.gif",100+(x*90),(12)+row*85); entities.add(alien); alienCount++; } } } } //private void initEntities() { public void initAlienEntities() { Random randomAlien = new Random(); // create the player ship and place it roughly in the center of the screen //ship = new ShipEntity(this,"sprites/ship.gif",370,550);//orignal //ship = new ShipEntity(this,"sprites/ship.gif",700,300);//changed postioning to right hand side //entities.add(ship); // create a block of aliens (5 rows, by 12 aliens, spaced evenly) alienCount = 0; levelCount = levelCount + 0.10;//this increases the speed on every level for (int row=0;row<7;row++) {//altered number of rows for (int x=0;x<5;x++) { int r = randomAlien.nextInt(100);//loop added to produce random aliens if (r < 50){//randome check to show alien //Entity alien = new AlienEntity(this,"sprites/alien.gif",/*100+*/(x*50),(50)+row*30); Entity alien = new AlienEntity(this,"sprites/alien.gif",-250+(x*90),(12)+row*85); entities.add(alien); alienCount++; } } } advanceAlienSpeed(levelCount); } /** * Notification from a game entity that the logic of the game * should be run at the next opportunity (normally as a result of some * game event) */ public void updateLogic() { logicRequiredThisLoop = true; } /** * Remove an entity from the game. The entity removed will * no longer move or be drawn. * * @param entity The entity that should be removed */ public void removeEntity(Entity entity) { removeList.add(entity); } /** * Notification that the player has died. */ public void notifyDeath() { message = "Oh no! They got you, try again?"; waitingForKeyPress = true; } /** * Notification that the player has won since all the aliens * are dead. */ public void notifyWin() { message = "Well done! You Win!"; waitingForKeyPress = true; } /** * Notification that an alien has been killed */ public void notifyAlienKilled() { // reduce the alient count, if there are none left, the player has won! alienCount--; if (alienCount == 0) { //notifyWin();win not relevant here... this.initAlienEntities();//call fresh batch of aliens } // if there are still some aliens left then they all need to get faster, so // speed up all the existing aliens advanceAlienSpeed(1.30); } public void advanceAlienSpeed(double speed) { // if there are still some aliens left then they all need to get faster, so // speed up all the existing aliens for (int i=0;i<entities.size();i++) { Entity entity = (Entity) entities.get(i); if (entity instanceof AlienEntity) { // speed up by 2% entity.setHorizontalMovement(entity.getHorizontalMovement() * speed); //entity.setVerticalMovement(entity.getVerticalMovement() * 1.02); } } } /** * Attempt to fire a shot from the player. Its called "try" * since we must first check that the player can fire at this * point, i.e. has he/she waited long enough between shots */ public void tryToFire() { // check that we have waiting long enough to fire if (System.currentTimeMillis() - lastFire < firingInterval) { return; } // if we waited long enough, create the shot entity, and record the time. lastFire = System.currentTimeMillis(); ShotEntity shot = new ShotEntity(this,"sprites/shot.gif",ship.getX()+10,ship.getY()-30); entities.add(shot); } /** * The main game loop. This loop is running during all game * play as is responsible for the following activities: * <p> * - Working out the speed of the game loop to update moves * - Moving the game entities * - Drawing the screen contents (entities, text) * - Updating game events * - Checking Input * <p> */ public void gameLoop() { long lastLoopTime = System.currentTimeMillis(); // keep looping round til the game ends while (gameRunning) { // work out how long its been since the last update, this // will be used to calculate how far the entities should // move this loop long delta = System.currentTimeMillis() - lastLoopTime; lastLoopTime = System.currentTimeMillis(); // Get hold of a graphics context for the accelerated // surface and blank it out Graphics2D g = (Graphics2D) strategy.getDrawGraphics(); g.setColor(Color.black); g.fillRect(0,0,800,600); // cycle round asking each entity to move itself if (!waitingForKeyPress) { for (int i=0;i<entities.size();i++) { Entity entity = (Entity) entities.get(i); entity.move(delta); } } // cycle round drawing all the entities we have in the game for (int i=0;i<entities.size();i++) { Entity entity = (Entity) entities.get(i); entity.draw(g); } // brute force collisions, compare every entity against // every other entity. If any of them collide notify // both entities that the collision has occured for (int p=0;p<entities.size();p++) { for (int s=p+1;s<entities.size();s++) { Entity me = (Entity) entities.get(p); Entity him = (Entity) entities.get(s); if (me.collidesWith(him)) { me.collidedWith(him); him.collidedWith(me); } } } // remove any entity that has been marked for clear up entities.removeAll(removeList); removeList.clear(); // if a game event has indicated that game logic should // be resolved, cycle round every entity requesting that // their personal logic should be considered. if (logicRequiredThisLoop) { //g.drawString("Press any key",(800-g.getFontMetrics().stringWidth("Press any key"))/2,300); for (int i=0;i<entities.size();i++) { Entity entity = (Entity) entities.get(i); entity.doLogic(); } logicRequiredThisLoop = false; } // if we're waiting for an "any key" press then draw the // current message //show highscore at top of screen //show name at top of screen g.setColor(Color.white); g.drawString("Player : "+getPlayer()+" : Score : "+getHighscore(),20,20); if (waitingForKeyPress) { g.setColor(Color.white); g.drawString(message,(800-g.getFontMetrics().stringWidth(message))/2,250); g.drawString("Press any key",(800-g.getFontMetrics().stringWidth("Press any key"))/2,300); } // finally, we've completed drawing so clear up the graphics // and flip the buffer over g.dispose(); strategy.show(); // resolve the movement of the ship. First assume the ship // isn't moving. If either cursor key is pressed then // update the movement appropraitely ship.setVerticalMovement(0);//set to vertical movement if ((leftPressed) && (!rightPressed)) { ship.setVerticalMovement(-moveSpeed);//**took out setHorizaontalMOvement } else if ((rightPressed) && (!leftPressed)) { ship.setVerticalMovement(moveSpeed);//**took out setHorizaontalMOvement } // if we're pressing fire, attempt to fire if (firePressed) { tryToFire(); } // finally pause for a bit. Note: this should run us at about // 100 fps but on windows this might vary each loop due to // a bad implementation of timer try { Thread.sleep(10); } catch (Exception e) {} } } /** * A class to handle keyboard input from the user. The class * handles both dynamic input during game play, i.e. left/right * and shoot, and more static type input (i.e. press any key to * continue) * * This has been implemented as an inner class more through * habbit then anything else. Its perfectly normal to implement * this as seperate class if slight less convienient. * * @author Kevin Glass */ private class KeyInputHandler extends KeyAdapter { /** The number of key presses we've had while waiting for an "any key" press */ private int pressCount = 1; /** * Notification from AWT that a key has been pressed. Note that * a key being pressed is equal to being pushed down but *NOT* * released. Thats where keyTyped() comes in. * * @param e The details of the key that was pressed */ public void keyPressed(KeyEvent e) { // if we're waiting for an "any key" typed then we don't // want to do anything with just a "press" if (waitingForKeyPress) { return; } // if (e.getKeyCode() == KeyEvent.VK_LEFT) { ////leftPressed = true; ///} //// if (e.getKeyCode() == KeyEvent.VK_RIGHT) { //rightPressed = true; if (e.getKeyCode() == KeyEvent.VK_UP) { leftPressed = true; } if (e.getKeyCode() == KeyEvent.VK_DOWN) { rightPressed = true; } if (e.getKeyCode() == KeyEvent.VK_SPACE) { firePressed = true; } } /** * Notification from AWT that a key has been released. * * @param e The details of the key that was released */ public void keyReleased(KeyEvent e) { // if we're waiting for an "any key" typed then we don't // want to do anything with just a "released" if (waitingForKeyPress) { return; } if (e.getKeyCode() == KeyEvent.VK_UP) {//changed from VK_LEFT leftPressed = false; } if (e.getKeyCode() == KeyEvent.VK_DOWN) {//changed from VK_RIGHT rightPressed = false; } if (e.getKeyCode() == KeyEvent.VK_SPACE) { firePressed = false; } } /** * Notification from AWT that a key has been typed. Note that * typing a key means to both press and then release it. * * @param e The details of the key that was typed. */ public void keyTyped(KeyEvent e) { // if we're waiting for a "any key" type then // check if we've recieved any recently. We may // have had a keyType() event from the user releasing // the shoot or move keys, hence the use of the "pressCount" // counter. if (waitingForKeyPress) { if (pressCount == 1) { // since we've now recieved our key typed // event we can mark it as such and start // our new game waitingForKeyPress = false; startGame(); pressCount = 0; } else { pressCount++; } } // if we hit escape, then quit the game if (e.getKeyChar() == 27) { //cThread.interrupt(); System.exit(0); } } } /** * The entry point into the game. We'll simply create an * instance of class which will start the display and game * loop. * * @param argv The arguments that are passed into our game */ //public static void main(String argv[]) { //Game g =new Game(); // Start the main game loop, note: this method will not // return until the game has finished running. Hence we are // using the actual main thread to run the game. //g.gameLoop(); //} }

  Read the article

< Previous Page | 37 38 39 40 41