Search Results

Search found 2905 results on 117 pages for 'supply chain logistics'.

Page 41/117 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

• What parts should I get for an ASRock x58 Extreme motherboard

  - by Brad Gilbert

  I just received an ASRock x58 Extreme motherboard, for my post on this question. It was a 2009 Tom's Hardware recommended buy. It is a Core i7 motherboard, with an X58 Express Chipset. It uses DDR3 RAM. What I want to know is, what parts should I get to finish it off. I'm looking for some good bargains, because of a lack of funds. The most taxing game I will probably play on it is OpenTTD. The only parts I currently have that are compatible: A Dynex 400W power supply. It appears to be an ATX 2.1 power supply, with the addition of a -5 rail. Apparently designed to be compatible with most ATX-style motherboards. Several PCI add-in cards. Mostly 10/100 Network cards Some sound cards Some video cards with a VGA connector Plenty of PATA drives. 8 GB - 80 GB Hard-drives A dozen or-so CD-ROM drives, only a handful of them are CD-RW drives. One DVD-ROM drive I have one LCD, with a 15 pin VGA connector, which I salvaged from the dump. The only thing wrong with it was some dead capacitors. It also has a stuck pixel.

  Read the article

• How do I upgrade the BIOS to boot the motherboard when the CPU is not suported?

  - by Matt

  So I have a Tyan S8225 motherboard with a Valencia (Opteron 4200) CPU. Two of us have tried everything. We have even swapped the whole motherboard, Power supply, memory, even a different CPU (still Valencia). We even tried it without any memory installed and with only a single CPU. There are no beep codes as I suspect even those are controlled by the BIOS boot process. We put the whole thing on the bench with just the power supply, VGA, keyboard and network (for IPMI) connected. The IPMI is not even showing the BIOS starting, but the IPMI is working. After some hunting around, I discovered the claim on the website is that the Valencia CPU's are not supported on older BIOS revisions. For a start, I don't know what the bios revision is and if it's older but it's the only thing left. Could the BIOS be causing a board not to boot at all? If that's the case, then is there any other way to update the BIOS without buying an old CPU only to be put back in a box just to update the BIOS? Yes, we even tried updating the BIOS through IPMI but you can't do that either.

  Read the article

• VirtualHost not using correct SSL certificate file

  - by Shawn Welch

  I got a doozy of a setup with my virtual hosts and SSL. I found the problem, I need a solution. The problem is, the way I have my virtual hosts and server names setup, the LAST VirtualHost directive is associating the SSL certificate file with the ServerName regardless of IP address or ServerAlias. In this case, SSL on www.site1.com is using the cert file that is established on the last VirtualHost; www.site2.com. Is this how it is supposed to work? This seems to be happening because both of them are using the same ServerName; but I wouldn't think this would be a problem. I am specifically using the same ServerName for a purpose and I really can't change that. So I need a good fix for this. Yes, I could buy another UCC SSL and have them both on it but I have already done that; these are actually UCC SSLs already. They just so happen to be two different UCC SSLs. <VirtualHost 11.22.33.44:80> ServerName somename ServerAlias www.site1.com UseCanonicalName On RewriteEngine On RewriteOptions Inherit </VirtualHost> <VirtualHost 11.22.33.44:443> ServerName somename ServerAlias www.site1.com UseCanonicalName On SSLEngine on SSLCertificateFile /usr/local/apache/conf/ssl.crt/cert1.crt SSLCertificateKeyFile /usr/local/apache/conf/ssl.key/cert1.key SSLCertificateChainFile /usr/local/apache/conf/chain/gd_bundle.crt RewriteEngine On RewriteOptions Inherit </VirtualHost> <VirtualHost 55.66.77.88:80> ServerName somename ServerAlias www.site2.com UseCanonicalName On RewriteEngine On RewriteOptions Inherit </VirtualHost> <VirtualHost 55.66.77.88:443> ServerName somename ServerAlias www.site2.com UseCanonicalName On SSLEngine on SSLCertificateFile /usr/local/apache/conf/ssl.crt/cert2.crt SSLCertificateKeyFile /usr/local/apache/conf/ssl.key/cert2.key SSLCertificateChainFile /usr/local/apache/conf/chain/gd_bundle.crt RewriteEngine On RewriteOptions Inherit </VirtualHost>

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• i7 overclocking problem

  - by benwebdev

  Hi everyone, I've got an overclocked system that seems to be misbehaving. When trying to boot up from cold the system just hangs and nothing is output to the screen. Fans are on as they should but nothing happens to finish the boot. From here I have to switch it off then on again and the boot completes. If I go into the tweak menu in the BIOS I'm informed that a boot has failed I've been in touch with Overclockers UK support a bit and theres not yet been a solution. We've mainly been tweaking the voltage for the CPU. Any suggestions? I'm new to Overclocking which is why I got a bundle with OCUK. With this issue happening on Cold Boot too its tricky to test as I have to make a change then wait till the next day. My system is here: Intel Core i7 930 2.80Ghz overclocked to 4GHz Gigabyte X58A-UD3R (BIOS Version: FC) 6GB RAM Power Supply - CoolerMaster Silent Pro M series 700W One suggestion made by OCUK was that maybe its the power supply but I'm not sure and dont have a spare - it's brand new and a pretty expensive piece of kit. Any thoughts on this? Other recomendations for Power? thanks Ben

  Read the article

• Rsync when run in cron doesnt work. Rsync between Mac Os x Server and Linux Centos

  - by Brady

  I have a working rsync setup between Mac OS X Server and Linux Centos when run manually in a terminal. I enter the rsync command, it asks for the password, I enter it and off it goes, runs and completes. Now I know thats working I set out to fully automate it via cron. First off I create an SSH authorized key by running this command on the Mac server: ssh-keygen -t dsa -b 1024 -f /Users/admin/Documents/Backup/rsync-key Entering the password and then confirming it. I then copy the rsync-key.pub file accross to the linux server and place in the rsync user .ssh folder and rename to authorized_keys: /home/philosophy/.ssh/authorized_keys I then make sure that the authorized_keys file is chmod 600 in the folder chmod 700. I then setup a shell script for cron to run: #!/bin/bash RSYNC=/usr/bin/rsync SSH=/usr/bin/ssh KEY=/Users/admin/Documents/Backup/rsync-key RUSER=philosophy RHOST=example.com RPATH=data/ LPATH="/Volumes/G Technology G Speed eS/Backup" $RSYNC -avz --delete --progress -e "$SSH -i $KEY" "$LPATH" $RUSER@$RHOST:$RPATH Then give the shell file execute permissions and then add the following to the crontab using crontab -e: 29 12 * * * /Users/admin/Documents/Backup/backup.sh I check my crontab log file after the above command should run and I get this in the log and nothing else: Feb 21 12:29:00 fileserver /usr/sbin/cron[80598]: (admin) CMD (/Users/admin/Documents/Backup/backup.sh) So I asume everything has run as it should. But when I check the remote server no files have been copied accross. If I run the backup.sh file in a terminal as normal it still prompts for a password but this time its through the Mac Key chain system rather than typing into the console window. With the Mac Key Chain I can set it to save the password so that it doesnt ask for it again but Im sure when run with cron this password isnt picked up. This is where I'm asuming where rsync in cron is failing because it needs a password to connect but I thought the whole idea of making the SSH keys was to prevent the use of a password. Have I missed a step or done something wrong here? Thanks Scott

  Read the article

• Squid with mikrotik router

  - by niren

  I tried to connect squid3 in my network to use high anonymity proxy. This is how my network is right now WAN LINK | ------------- ----------------------------- | Mikrotik Box | | Ubuntu Server with squid3 | ------------- ----------------------------- | / | / ---------------------- | Switch ( Cheap one ) | ---------------------- | | | Client1 Client2 Client3 etc. after this setup I changed squid.conf in Ubuntu server as http_port 8080 acl localhost src xxx.xxx.xxx.xxx(Ubuntu server IP) acl to_localhost dst xxx.xxx.xxx.xxx(Mikrotik router gateway) I assume that redirected http from Mikrotik router will be redirect again to Mikrotik router. uncomment access log /var/log/squid3/access.log add visible_hostname myname save squid.conf and restart squid3 server. Then I have added nat rule in Mikrotik router ip/firewall/nat 1. add chain=dstnat src_address=xxx.xxx.xxx.xxx(ununtu server IP) dst-port=80 protocol=tcp action=accept 2. add chain=dstnat src_address=xxx.xxx.xxx.xxx/28(LAN address) dst-port=80 protocol=tcp action=dst-nat to-address=xxx.xxx.xxx.xxx(ununtu server IP) to-port=8080 now I can not able to access internet from client1 system, If I remove these two nat rule then I can access internet. what is wrong I have made?

  Read the article

• Notebook Operating System with extreme support cycles/security updates

  - by leto

  Hello there, after reading the announcements about Mac OS X "Lion" and Apples political decision, I've had enough. I'm a longtime Apple User since 1992, have always felt at home there, but am trying to switch to alternative Operating System since a year. I've also been working with Unix machines since 2001, so I'm looking in one of the free Unices or a Linux. Since I last looked at the desktop in 2002 choke much has changed, it seems. So I'm lost once more in the war between desktop environments and software. To be honest: I don't care what it's name is, I want to get my job done. Here's what I set me as landmark for an operating system/software to be considered: Has to be atleast four years old Has to supply security updates for current release for atleast a year Production quality stability for the whole desktop environment (!) No f****g commercial stuff that tends to supply me with privacy invading App Store or Cloud space So far I'm running a MacBook from 2007, 4 Gig memory, 250 Gig disk and I need: IMAPs for Mail since 1995 Webbrowser sic Shell Keeping current with Updates/Upgrades with no more than 5 Minutes spent in entering commands (makes it hard for OpenBSD ;-) ) A desktop filemanger would be nice, but is a bonus. What can you suggest as operating system? The one with the longest support cycles and best chance to survive the next 10 years will win a new user, even sending patches when needed :-) Greets

  Read the article

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• Where is my problem? The P6X58D Premium Mobo, Windows 7, or other?

  - by Dylan Yaga

  I was having problems with my USB devices for an hour last night, and I am unable to determine the root cause of the problem. The two symptoms are: At seemingly random times (not consistently spaced by time or caused by any detectable event) my USB devices become "detached". Windows will play the USB disconnect sound and then the reconnect sound. The devices disconnected and then reconnected. My USB Keyboard will "stick" on one key for several seconds before processing any other keystroke made. The mouse also does not respond to clicks. I do not lose mouse movement or USB device connectivity. And after a moment of this several beeps will be emitted from the speakers. Hardware Specs: GFX Card: EVGA GeForce GTX 470 Superclocked 1280MB DDR5 PCIe Motherboard: ASUS P6X58D Premium Intel X58 Socket LGA1366 MB Processor: Intel Core i7-920 2.66Ghz 8M LGA1366 CPU Memory: Corsair Dominator 6144MB PC12800 DDR3 Storage: Hitachi 1TB Serial ATA HD 1600MHz 7200/32MB/SATA-3G Cooling: Corsair Hydro H50 CPU Liquid Cooler Case: Corsair Obsidian 800D Full Tower Case Power Supply: Corsair HX1000W 1000W Modular Power Supply Steps I have taken to narrow down the problem: Restarted the computer. - No change Changed USB port the Hub was connected to on the CPU. - No change Removed all devices from USB Hub and connected directly to CPU. - No change Used a different USB keyboard both in USB Hub and directly to CPU. - No change Disconnected and reconnected all cables. - No change Disassembled the Tower and determined if the USB headers were firmly connected. - No change Checked device manager for errors. Checked all USB devices. - Nothing flagged After an hour of frustration trying to narrow down the problem it appeared to disappear. But I am torn between it being a Mobo problem or an OS problem. Is there anything else I can do to narrow down the problem before a reformat and then eventually exchanging the Mobo?

  Read the article

• Daisy-chainable DisplayPort Monitors

  - by thepurplepixel

  I am the proud new owner of a MacBook Pro with a mini-DisplayPort. My desk setup used to allow me to position the screen of my old MacBook beside an external monitor, essentially allowing dual-head. It was also advantageous that my old MBP and my external monitor had the same resolution, 1440x900. Now, I'm searching for a set of two monitors that I can use a HengeDock with. Unfortunately, the MacBook Pro suffers from having only one mini-DisplayPort. Looking up the spec for DisplayPort 1.2 (which the MBP supports), DisplayPort daisy chaining is supported. What I'm looking for is a monitor that has two DisplayPorts so I can daisy chain two monitors off the single mini-DisplayPort. What I don't want is a USB-based video solution. I need full acceleration on both monitors; an external video card won't cut it. I hope I don't have to wait a few years for these monitors to come out. TL;DR: I need two monitors with two DisplayPorts each that I can daisy-chain. Thanks!

  Read the article

• iptables to block non-VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• BIOS not detecting working SATA hard drive.

  - by Evan

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• OS X can connect to Windows machine, but can't access shared folders

  - by Bonnie

  I can create new folders on my Windows XP machine, set them to "shared". On my Mac, I pick Finder → Go → Connect to Server → smb://192.168.1.4 → Connect → Name / Password. It even shows me all the names of the newly created shared-folders on my PC, but when I try to actually connect to any of them I get connection failed, there was an error connecting Any idea on what would cause that? The fact that it successfully gets so far—to actually showing me my PC share-names—must mean I have 99% of this working correctly, i.e. the physical connection, the IP address, the user name, the password, etc. Still, I can't seem to access the folders themselves. I've tried this with my Windows XP firewall on/off, and Norton AntiVirus on/off. Same problem. Everything did work fine, 4 months ago. Were there any odd OS X or Windows updates released recently? I always apply them all. smbclient on the Mac does correctly find the XP machine, my XP user name, and accepts my XP password. I get the following from that smbclient command: Doing spnego session setup (blob length=16) server didn't supply a full spnego negprot Got challenge flags: ... Got NTLMSSP flags: ... Got NTLMSP flags: ... Domain=[XPMACHINE] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] tree connect failed: NT_STATUS_INSUFF_SERVER_RESOURCES I'm not sure why a standard XP box can't "supply a full spnego negprot". Whatever that means. Using XP's RegEdit to change my IRPStackSize from 11... to 13, 15, 20, 22... still gives that "NT_STATUS_INSUFF_SERVER_RESOURCES" error on the Mac.

  Read the article

• iptables to block VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Hardware issue, bsod with windows xp irq and strange messages with ubuntu

  - by JP Hellemons

  I have an old Acer T160 and it used to run Windows XP. But I keep getting random BSOD's. I keep seeing IRQ conflicts. I tried to run ubuntu, which runs and keeps running. But sometimes is not responding. Also there are these popups at ubuntu 12.04 that my network cable (which is onboard) is unplugged. But I have no cable in it! and have an usb dongle for wifi. which also seems unstable. have to (auto)reconnect sometimes. So my question is: is it my mobo, power supply or something else? FYI: I had an dvd-rw station which did not open properly, so unplugged the ata and power, als removed the second harddrive. now only have sata harddrive. also removed the extra video card (ati sapphire x1600 pro) so use only onboard video now and still have these issues. EDIT Update: will try with a new PSU (power supply unit of 400watt) the old (factory) one was 300watt. and will use a usb drive which has 12.04 ubuntu on it (made with unetbootin) to format everything and re-install ubuntu. (so also delete mbr partition) will update the day after tomorrow.

  Read the article

• iptables firewall rules not allowing ssh from lan to DMZ

  - by ageis23

  Chain INPUT (policy ACCEPT) target prot opt source destination REJECT tcp -- anywhere anywhere tcp dpt:www reject-with tcp-reset REJECT tcp -- anywhere anywhere tcp dpt:telnet reject-with tcp-reset ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED DROP udp -- anywhere anywhere udp dpt:route DROP udp -- anywhere anywhere udp dpt:route ACCEPT udp -- anywhere anywhere udp dpt:route logdrop icmp -- anywhere anywhere logdrop igmp -- anywhere anywhere ACCEPT udp -- anywhere anywhere udp dpt:5060 ACCEPT 0 -- anywhere anywhere state NEW logaccept 0 -- anywhere anywhere state NEW ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere logdrop 0 -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT 0 -- 192.168.0.0/24 192.168.2.0/24 reject-with icmp-port-unreachable ACCEPT tcp -- choister 192.168.2.142 tcp dpt:ssh state NEW REJECT 0 -- 192.168.0.0/24 192.168.3.0/24 reject-with icmp-port-unreachable ACCEPT gre -- 192.168.1.0/24 anywhere ACCEPT tcp -- 192.168.1.0/24 anywhere tcp dpt:1723 ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU lan2wan 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED logaccept tcp -- anywhere choister tcp dpt:www TRIGGER 0 -- anywhere anywhere TRIGGER type:in match:0 relate:0 trigger_out 0 -- anywhere anywhere logaccept 0 -- anywhere anywhere state NEW logdrop 0 -- anywhere anywhere The ssh server I'm trying to connect to is in the DMZ(192.168.0.145). It's mainly used as a web server. I need access to it from my room 192.168.2.142. I don't get why ssh can't forward onto the 192.168.2.0 subnet? I'm sure it's the reject rule that causing this because it works without it.

  Read the article

• iptables drops some packets on port 80 and i don't know the cause.

  - by Janning

  Hi, We are running a firewall with iptables on our Debian Lenny system. I show you only the relevant entries of our firewall. Chain INPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW Chain OUTPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Some packets get dropped each day with log messages like this: Feb 5 15:11:02 host1 kernel: [104332.409003] dropped IN= OUT=eth0 SRC= DST= LEN=1420 TOS=0x00 PREC=0x00 TTL=64 ID=18576 DF PROTO=TCP SPT=80 DPT=59327 WINDOW=54 RES=0x00 ACK URGP=0 for privacy reasons I replaced IP Addresses with and This is no reason for any concern, but I just want to understand what's happening. The web server tries to send a packet to the client, but the firewall somehow came to the conclusion that this packet is "UNRELATED" to any prior traffic. I have set a kernel parameter ip_conntrack_ma to a high enough value to be sure to get all connections tracked by iptables state module: sysctl -w net.ipv4.netfilter.ip_conntrack_max=524288 What's funny about that is I get one connection drop every 20 minutes: 06:34:54 droppedIN= 06:52:10 droppedIN= 07:10:48 droppedIN= 07:30:55 droppedIN= 07:51:29 droppedIN= 08:10:47 droppedIN= 08:31:00 droppedIN= 08:50:52 droppedIN= 09:10:50 droppedIN= 09:30:52 droppedIN= 09:50:49 droppedIN= 10:11:00 droppedIN= 10:30:50 droppedIN= 10:50:56 droppedIN= 11:10:53 droppedIN= 11:31:00 droppedIN= 11:50:49 droppedIN= 12:10:49 droppedIN= 12:30:50 droppedIN= 12:50:51 droppedIN= 13:10:49 droppedIN= 13:30:57 droppedIN= 13:51:01 droppedIN= 14:11:12 droppedIN= 14:31:32 droppedIN= 14:50:59 droppedIN= 15:11:02 droppedIN= That's from today, but on other days it looks like this, too (sometimes the rate varies). What might be the reason? Any help is greatly appreciated. kind regards Janning

  Read the article

• Getting a "CPU over temperature error", but temperatures seem to be normal

  - by Luis Parker

  I built a PC with the following parts: CPU: i5-2500 Motherboard: Asus P8H67-M EVO rev 3.0 RAM: G-Skill Ripjaws Series 8GB (2 x 4GB) DDR3 1333 Video: GTX 560-Ti 1GB I used a crappy (but functioning) old case and a 500W Powercooler supply. The rig also includes 3 HDs and a DVD-RW. Whenever I push the system mildly it resets right away (looks more like power off/power on) and gives me a "CPU over temperature error". However, BIOS always reports <65ºC for the CPU at the moment of the reset, same as Core Temp and RealTemp. This is RealTemp's log since launching BF3 until the reset (just over 1 minute, as you can see) Just to be sure I've checked the CPU cooler and re-applied the thermal paste twice, but nothing changed. I'm not overclocking at all. What am I missing here? Could it be that the old power supply is generating this error? Maybe the mobo isn't reporting temperatures correctly? I don't have a clue on how to troubleshoot this, help Thanks in advance!

  Read the article

• Possible for linux bridge to intercept traffic?

  - by A G

  I have a linux machine setup as a bridge between a client and a server; brctl addbr0 brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1 0.0.0.0 ifconfig eth2 0.0.0.0 ip link set br0 up I also have an application listening on port 8080 of this machine. Is it possible to have traffic destined for port 80 to be passed to my application? I have done some research and it looks like it could be done using ebtables and iptables. Here is the rest of my setup: //set the ebtables to pass this traffic up to ip for processing; DROP on the broute table should do this ebtables -t broute -A BROUTING -p ipv4 --ip-proto tcp --ip-dport 80 -j redirect --redirect-target DROP //set iptables to forward this traffic to my app listening on port 8080 iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 8080 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1/1 //once the flows are marked, have them delivered locally via loopback interface ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 //enable ip packet forwarding echo 1 > /proc/sys/net/ipv4/ip_forward However nothing is coming into my application. Am I missing anything? My understanding is that the target DROP on the broute BROUTING chain will push it up to be processed by iptables. Secondly, are there any other alternatives I should investigate? Edit: IPtables gets it at nat PREROUTING, but it looks like it drops after that; the INPUT chain (in either mangle or filter) doesn't see the packet.

  Read the article

• How to diagnose a spontaneous reboot?

  - by Spectralist

  My computer reboots, seemingly completely at random, about once every week to two weeks but has occasionally gone months. It just goes from running fine to the POST with no error messages or anything and doesn't seem to be due to heat or usage as it's happened a couple of times when the computer has booted just a few moments ago and is idling. It's been happening for as long as I've had this computer, almost two years. It's happened in both Vista and Windows7. I strongly suspect it's a hardware problem. But due to the rareish and random nature of the crashes my normal strategy of just removing hardware until the problem stops isn't really practical. My guess would be Power Supply, Ram, or Motherboard. But I just don't know how to test an issue this random and want to figure out how to confirm which it is before I go replacing things. So is there some software or hardware that can be used to test these sorts of errors? I did run memtest86 for about 8 hours without finding any issues. And the power supply is more than capable of running my system.

  Read the article

• What could possibly cause my computer to power down at random times?

  - by geoffreydv

  I have recently bought a new Power Supply and a new graphics card. My PC ran smoothly for a few months now but since a couple of days I'm having a strange problem. I am trying to isolate the problem to a specific piece of hardware (because if it's either the Power Supply or the Graphics card they are still under warranty). The problem started when I was playing a game (diablo 3). My PC suddenly powered down. I was unable to turn it on again by pressing the power button. I unplugged the power cable for a few seconds and plugged it back in. This time the pc powered on but the indication light turned orange instead of white as it normally does. The fans were not spinning and I did not see anything on my screen. After trying a couple of times I gave up. Two days later I tried again and this time the PC did boot up as usual. Everything looked okay until I tested if the problem was resolved by starting Diablo again. After about two minutes it powered down again as it did the first time. If I don't run any games my PC does power down after about 3-5 hours. Another fact that might be relevant: One time the PC did not shut down immediatly, instead first my graphics "powered down" but the music I was playing kept on playing. After about 20 seconds the pc powered down completely as usual. What I also noticed is that when I boot instantly after a power down, the chance of another power down occuring is much higher. Does anyone have an idea what could be causing this kind of behaviour or has a certain tool to diagnose the specific hardware parts? Thanks Specs: Memory: 6GB Processor: Intel i5 OS: Windows 7 64 bit The PC is a Dell Studio XPS 8100 with a replaced PSU and Graphics card: PSU: Corsair CX500 (500 watt) Graphics card: AMD Radeon 6850

  Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >