Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 410/778 | < Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• Xen PV packet loss

  - by Delphinator

  I'm having some serious issues with packetloss with one of my servers. This server is a somewhat old (P4-era) machine running Debian Squeeze and Xen 4.0. There are two domUs running on it (both also Debian Squeeze), one gateway and a fileserver. Unfortunatly the processor has no virtualization extensions, therefore only PV can be used. While investigating why our network seems to be slower than it should I found some pretty bad packet loss (~25%). After further investigation and several experiments I did a measurment between the dom0 and one of the domUs: Server listening on UDP port 5001 Receiving 1470 byte datagrams UDP buffer size: 110 KByte (default) ------------------------------------------------------------ ------------------------------------------------------------ Client connecting to dom0, UDP port 5001 Sending 1470 byte datagrams UDP buffer size: 110 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.2(domU) port 33817 connected with 192.168.1.100(dom0) port 5001 [ 4] local 192.168.1.2(domU) port 5001 connected with 192.168.1.100(dom0) port 48606 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 46.3 MBytes 38.7 Mbits/sec [ 3] Sent 33020 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 46.2 MBytes 38.6 Mbits/sec 0.030 ms 89/33019 (0.27%) [ 3] 0.0-10.0 sec 1 datagrams received out-of-order [ 4] 0.0-10.2 sec 43.0 MBytes 35.3 Mbits/sec 13.074 ms 11575/42256 (27%) tl;dr: 27% packet loss from dom0 to domU with 50Mbit UDP packets. Same thing happens from anywhere in the network. The problem gets better for smaller bandwidths (0.047% for 5Mbit) and worse for higher (59% for 200Mbit) ones. I did increase the CPU-weight of the dom0, there is no swapping going on, and actual networking-hardware is not involved. I never expected Xen (or anything related) to drop packets, and I'm completly clueless what to try next.

  Read the article

• Multiple Servers + One MailServer

  - by theomega

  Hy, I got several Linux-Servers (running Debian) where different services run: Database-Servers, Webservers, Applicationsservers, Tools and so on. All Servers are connected to the same internal network. There is also one special Server which is the Mail-Server: All Mailaccounts are stored on this server, it is also the outbound Mailserver for all the other servers. I want all Mails for all servers to get saved on the Mailserver. For example if an cron-job fails on one of the web-servers the mail should not be delivered to the local user but instead to the Mailserver so I get a centralized place for mail storage. How do you set up this scenario? My current setup is: Using postfix as MTA on the Mailserver and using ssmtp on all the other servers. SSMTP is configured to send the mails to the Mailserver. The Mailserver is configured to allow the whole internal network to relay mails using itself. Is this the right way to choose? I also thought about setting up a MTA (postfix) on every server and configure it somehow to forward the mails. What would be the advantage of this solution?

  Read the article

• FreeBSD ZFS RAID-Z2 performance issues

  - by Axel Gneiting

  I'm trying to build my own network attached storage based on FreeBSD+ZFS+standard components, but there are strange performance issues. The hardware specs are: AMD Athlon II X2 240e processor ASUS M4A78LT-M LE mainboard 2GiB Kingston ECC DDR3 (two sticks) Intel Pro/1000 CT PCIe network adapter 5x Western Digital Caviar Green 1.5TB I created a RAID-Z2 zpool from all disks. I installed FreeBSD 8.1 on that zpool following the tutorial. The SATA controllers are running in AHCI mode. Output of zpool status: pool: zroot state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM zroot ONLINE 0 0 0 raidz2 ONLINE 0 0 0 gptid/7ef815fc-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/80344432-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/81741ad9-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/824af5cb-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/82f98a65-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 The problem is that write performance on the pool is very very bad (<10 MB/s) and every application that is accessing the disk is unresponsive every few seconds when writing. It seems like writing is fine until the ZFS ark cache is full and then ZFS stalls the entire system I/O till it's finished writing that data. Also I'm getting kmem_malloc to small kernel panics. I've already tried to put vm.kmem_size="1500M" vm.kmem_size_max="1500M" into /boot/loader.conf, but it doesn't help. Does anyone know what's going on here? Am I really not having enough memory for ZFS to handle this RAID-Z2?

  Read the article

• The Server Fault Wiki of recommended practices [migrated]

  - by Avery Payne

  So I've noticed that there are several recommendations on basic practices on Server Fault, but there doesn't seem to be a cohesive view as to how those recommendations would all fit together. So I thought I would lump these together as a kind of mental exercise to see what the "ServerFault Community IT Department" would look like if it were implemented. This would give a few things: it would make a reasonable wiki (in the true wiki spirit of many contributions), it would provide several links to well-vetted practices, and it would be kind of fun to see what the amalgamation would look like. And who knows, it may even point out some interesting issues between different forms of "best practices", although I would be stunned if there was a conflict hidden in there someplace... Add your favorites from Server Fault as answers, and I'll re-edit this section with the results. Here's a few catagories to collect different ideas together. Hardware Configuration(s) Server room configuration. Server room temperature Firmware Updates and Scheduling Storage Configuration(s) Selecting a NAS box Linux: Dealing with /tmp Linux: Install apps in /var or /opt? Network Configuration(s) checking DNS health and compliance Security Practice(s) Password (General) Best Practices Password sharing methods Windows Update Updating Windows Servers that are hosts for VMs Network Service(s) User Service(s) User Naming & Deletion Upgrade Process(es) Disaster Recovery Checking Backups Documenting an outage for a post-mortem review Last Edit: 2010-02-17

  Read the article

• Cisco Spam Blocker, Iron Port, Lotus Domino, Integration Help

  - by NickToyota

  Hi serverfault universe, I work for a medium sized (roughly 200 user) company. We are attempting to intagrate our new Cisco Spam Video Blocker (ironport) device into our network so that it acts as an incoming filter then passes it off to our Lotus domino mail server. And also vise versa. The way our network is setup currently has an mx record pointing to our Domino mail SMTP incoming server which is currently setup to be an inbound gateway and filter (using symantec domino mail software). We want to replace the inbound gateway with the ironport. Our company has also invested in a pool of external IP addresses which I believe has been currently assigned to our web, email, servers. What would the proper course of action be to successfully integrate the device be? Mx record change? Replace the domino gateway completely with the ironport? We attempted to set the ironport device to the external IP of what our mx record is pointing to without much success. Any help on proper setup would be greatly appreciated.

  Read the article

• Accessing Virtual Host from outside LAN

  - by Ray

  I'm setting up a web development platform that makes things as easy as possible to write and test all code on my local machine, and sync this with my web server. I setup several virtual hosts so that I can access my projects by typing in "project" instead of "localhost/project" as the URL. I also want to set this up so that I can access my projects from any network. I signed up for a DYNDNS URL that points to my computer's IP address. This worked great from anywhere before I setup the virtual hosts. Now when I try to access my projects by typing in my DYNDNS URL, I get the 403 Forbidden Error message, "You don't have permission to access / on this server." To setup my virtual hosts, I edited two files - hosts in the system32/drivers/etc folder, and httpd-vhosts.conf in the Apache folder of my WAMP installation. In the hosts file, I simply added the server name to associate with 127.0.0.1. I added the following to the http-vhosts.conf file: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot "c:/wamp/www/ladybug" ServerName ladybug ErrorLog "logs/your_own-error.log" CustomLog "logs/your_own-access.log" common </VirtualHost> <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot "c:/wamp/www" ServerName localhost ErrorLog "logs/localhost-error.log" CustomLog "logs/localhost-access.log" common </VirtualHost> Any idea why I can't access my projects from typing in my DYNDNS URL? Also, is it possible to setup virtual hosts so that when I type in http://projects from a random computer outside of my network, I access url.dyndns.info/projects (a.k.a. my WAMP projects on my home computer)? Help is much appreciated, thanks!

  Read the article

• Creating Active Directory on an EC2 box

  - by Chiggins

  So I have Active Directory set up on a Windows Server 2008 Amazon EC2 server. Its set up correctly I think, I never got any errors with it. Just to test that I got it all set up correctly, I have a Windows 7 Professional virtual machine set up on my network to join to AD. I set the VM to use the Active Directory box as its DNS server. I type in my domain to join it, but I get the following error: DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "ad.win.chigs.me": The query was for the SRV record for _ldap._tcp.dc._msdcs.ad.win.chigs.me The following domain controllers were identified by the query: ip-0af92ac4.ad.win.chigs.me However no domain controllers could be contacted. Common causes of this error include: - Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. It seems that I can talk to Active Directory, but when I'm trying to contact the Domain Controller, its giving a private IP to connect to, at least thats what I can make out of it. Here are some nslookup results. > win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Non-authoritative answer: Name: ec2-184-73-35-150.compute-1.amazonaws.com Address: 10.249.42.196 Aliases: win.chigs.me > ad.win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Name: ad.win.chigs.me Address: 10.249.42.196 win.chigs.me and ad.win.chigs.me are CNAME's pointing to my EC2 box. Any idea what I need to do so that I can join my virtual machine to the EC2 Active Directory set up I have? Thanks!

  Read the article

• Tcpreplaying using VMware

  - by Methos

  This is more like a testbed setup question. I want to use VMware to debug some networking code in the linux kernel in the VM. My VM has two network interfaces. What I want to do is replay the capture file in the host and receive the packets in the VM. My problem is I do not see replayed packets in the VM. I am running VMware and tcpreplay on the host as sudo. Hence I think there should not be any problem access devices files. I am running VMware workstation 7.0 a. I first began with Custom networking as that provides option of creating your own virtual network name. I wrote /dev/vmnet3 and /dev/vmnet4 for the two interfaces respectively. However, after booting the guest, I did not see any of these interfaces or devices files (in /dev) created on the host. b. Then I tried 'Host Only', but that does not show what bridge/device file is associated with the interface. c. Finally I tried bridged networking mode. I see vmnet1, vmnet8 and vboxnet0 on the host. I have tcpreplayed the capture file on each of these interfaces, for all the above three cases. I tried to capture packets in the VM using "tcpdump -i any". However, I do not see any packets. Any ideas/pointers?

  Read the article

• How does Windows 7 DNS client work?

  - by Mark Allison

  I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

  Read the article

• LDAP, Active Directory and bears, oh my!

  - by Tim Post

  What I have: Workstations running Ubuntu Jaunty mounting /home on a remote NFS server. User accounts are still created locally on each individual workstation. Workstations running Windows XP / Vista NFS server (as noted above) Windows 2008 server All machines share a single private network (LAN). What I need to accomplish: A single, intuitive (GUI driven) place for an office administrator to create user accounts. This should let anyone login to their (linux or windows) workstation, then fire up remote desktop and use the same login to the Windows 2008 server, from any machine on the network. I have read so much on samba, LDAP vs AD, etc and now I'm even more confused than I was before I began researching the problem. Ideally, Linux and Windows users should be able to get to their local files once logged into the Win2008 server. I am a programmer, not an interoperability guru and I'm completely lost on where to even start trying to accomplish this, plus I've run out of things to Google. How would you do this? Is it even possible?

  Read the article

• Which is the fastest way to move 1Petabyte from one storage to a new one?

  - by marc.riera

  First of all, thanks for reading, and sorry for asking something related to my job. I understand that this is something that I should solve by myself but as you will see its something a bit difficult. A small description: Now Storage = 1PB using DDN S2A9900 storage for the OSTs, 4 OSS , 10 GigE network. (lustre 1.6) 100 compute nodes with 2x Infiniband 1 infiniband switch with 36 ports After Storage = Previous storage + another 1PB using DDN S2A 990 or LSI E5400 (still to decide) (lustre 2.0) 8 OSS , 10GigE network 100 compute nodes with 2x Infiniband Previous experience: transfered 120 TB in less than 3 days using following command: tar -C /old --record-size 2048 -b 2048 -cf - dir | tar -C /new --record-size 2048 -b 2048 -xvf - 2>&1 | tee /tmp/dir.log So , big problem here, using big mathematical equations I conclude that we are going to need 1 month to transfer the data from one side to the new one. During this time the researchers will need to step back, and I'm personally not happy with this. I'm telling you that we have infiniband connections because I think that may be there is a chance to use it to transfer the data using 18 compute nodes (18 * 2 IB = 36 ports) to transfer the data from one storage to the other. I'm trying to figure out if the IB switch will handle all the traffic but in case it just burn up will go faster than using 10GigE. Also, having lustre 1.6 and 2.0 agents on same server works quite well, with this there is no need to go by 1.8 to upgrade the metadata servers with two steps. Any ideas? Many thanks Note 1: Zoredache, we can divide it in two blocks (A)600Tb and (B)400Tb. The idea is to move (A) to new storage which is lustre2.0 formated, then format where (A) was with lustre2.0 and move (B) to this lustre2.0 block and extend with the space where (B) was. This way we will end with (A) and (B) on separate filesystems, with 1PB each.

  Read the article

• Windows server 2008R2 routing with single NIC

  - by Fabian

  I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

  Read the article

• Hardware needed to route between two networks over wireless

  - by AptDweller

  I recently rented an apartment about 100 yards from my brother's house. I have line of sight to his house and can pick up his home AP signal with one of my two laptops if I go out on my balcony (facing his house) or put the laptop by the window. The other laptop will sometimes see the SSID broadcast, but fails to connect, drops, etc. We would like to set up a persistent wireless connection between our homes. We would prefer each network be logically segmented as independent networks, but he will share his internet connection. I've got a bunch of tv shows saved to a NAS by my TiVO that I'd like to make available to him across the wireless link. My brother strongly prefers to not mess with his WAP at all. His network is running fine and is afraid to mess it up. I guess you could say he is "technologically declined". If we can get a reliable 11Mbps connection we will be satisfied. What hardware do I need to make this work? I was thinking a router with two wireless interfaces (external antennas) a wired interface, and a directional antenna mounted on my balcony facing his house. Can anyone recommend hardware to make this happen? Cheaper is better. I'll only be living in the area a year or two. I do have an old satellite TV antenna if that can be used to direct the signal.

  Read the article

• SSH through standard Belkin router to Asus Tomato router

  - by Luke

  I've set up SSH on the Tomato firmware on an Asus N10, via port 22 with key authentication. I've tested the keys by connecting with putty directly to the router when connected to its network. That works OK. But this router is behind a Belkin (F5D7632-4) router which also acts as modem and when I try to connect through with the (dynamic) public IP it times out. I'm guessing it's something to do with the NAT? My putty settings are taken from various online tutorials, but it's set up for port 22, with the correct key as mentioned. The Belkin router has port forwarding to the Asus (192.168.2.3) for port 22 TCP and UDP set up. It's now tough to see what to do in order to connect to the Asus router with an external IP - if it's even possible. Ideally I would have liked to have only needed to use the Asus router, but as it doesn't act as a modem, I need to connect it to the Belkin to use Tomato's features. Perhaps there's a solution here too? Network: Internet -> Belkin modem/router -> Asus router (Tomato SSH) -> Devices

  Read the article

• Overriding some DNS entries in BIND for internal networks

  - by Remy Blank

  I have an internal network with a DNS server running BIND, connected to the internet through a single gateway. My domain "example.com" is managed by an external DNS provider. Some of the entries in that domain, say "host1.example.com" and "host2.example.com", as well as the top-level entry "example.com", point to the public IP address of the gateway. I would like hosts located on the internal network to resolve "host1.example.com", "host2.example.com" and "example.com" to internal IP addresses instead of that of the gateway. Other hosts like "otherhost.example.com" should still be resolved by the external DNS provider. I have succeeded in doing that for the host1 and host2 entries, by defining two single-entry zones in BIND for "host1.example.com" and "host2.example.com". However, if I add a zone for "example.com", all queries for that domain are resolved by my local DNS server, and e.g. querying "otherhost.example.com" results in an error. Is it possible to configure BIND to override only some entries of a domain, and to resolve the rest recursively?

  Read the article

• Google Chrome doesn't want to access Facebook

  - by Pieter van Niekerk

  I have been experiencing a bit of a problem with Chrome over the last couple of days where it doesn't want to access Facebook. When I open Chrome it works fine for a while and then if I were to refresh the page it would give me the Chrome 'This webpage is not available' message. This webpage is not available Google Chrome could not load the webpage because www.facebook.com took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection. Here are some suggestions: Reload this webpage later. Check your Internet connection. Restart any router, modem, or other network devices you may be using. Add Google Chrome as a permitted program in your firewall's or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again. If you use a proxy server, check your proxy settings or contact your network administrator to make sure the proxy server is working. If you don't believe you should be using a proxy server, adjust your proxy settings: Go to the wrench menu Options Under the Hood Change proxy settings... LAN Settings and deselect the "Use a proxy server for your LAN" checkbox. This problem only persists when using the proxy and doesn't occur at all when not on the proxy. I have also tried different browsers (IE9 and Firefox 9.01) but it doesn't occur in any of them. This problem goes away for a while when I restart Chrome, only to happen again a couple of minutes later. I have tried deleting the cookies for Facebook without restarting Chrome, but to no avail. I am using Windows7 with Chrome 17

  Read the article

• Remote SQL server connection failure

  - by Sevki

  I am trying to connect to my MSSQL server 2008 web instance and im failing horribly... i get the error 26 and before you jump on me i have done these Check the spelling of the SQL Server instance name that is specified in the connection string. Use the SQL Server Surface Area Configuration tool to enable SQL Server to accept remote connections over the TCP or named pipes protocols. For more information about the SQL Server Surface Area Configuration Tool, see Surface Area Configuration for Services and Connections. Make sure that you have configured the firewall on the server instance of SQL Server to open ports for SQL Server and the SQL Server Browser port (UDP 1434). Make sure that the SQL Server Browser service is started on the server. in addition to theese i have disabled the firewall completely and tried other ports nothing works the same credentials work on the server but not on the client. this is the exact error message A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (.Net SqlClient Data Provider) Can anybody help?

  Read the article

• Intermittent NFS lockups on Isilon cluster

  - by blackbox222

  We have an Isilon cluster with 8 IQ 12000x nodes which exports storage via several NFS shares for a handful of Linux and Solaris clients. There is a Linux system that has one of these NFS filesystems mounted. I/O to this filesystem is moderately heavy from the Linux system. Every 3-4 weeks (it's not on any kind of discernible schedule, and sometimes is more/less frequent than this), we notice that all activity ceases on this NFS mount (the process hangs, as if the network stopped working so process is stuck in uninterruptible sleep) - 30 minutes later, the share recovers and things continue to work normally. The kernel log from the affected machine is as follows: Dec 3 10:07:29 redacted kernel: [8710020.871993] nfs: server nfs-redacted not responding, still trying Dec 3 10:37:17 redacted kernel: [8711805.966130] nfs: server nfs-redacted OK relevant /etc/fstab line: nfs-redacted:/ifs/nfs/export_data/shared/...redacted... /data nfs defaults 0 0 I've checked to see if there are any scheduled processes e.g. cron jobs, Isilon related functions e.g. snapshots, etc that might be causing these hangups but I can't seem to find anything. I'm also not aware of any network related issues or maintenance that would cause this. All of the lockups last almost exactly 30 minutes per the kernel logs. Perhaps someone has some suggestions I could try? (I considered a soft mount to avoid the problems associated with processes accessing the filesystem hanging; however am wary of the corruption that could result and it would not really solve the underlying issue anyway).

  Read the article

• cannot connect to <server_name>\sqlexpress

  - by Jackson Sunuwar

  I have tried disabling firing wall and checked sqlbrowser is started but for some reason I cannnot connect to my datbase... called server_name\sqlexpress.. I have a virtual machine and a full scale MS SQL Server 2008 R2 running on it... and I have several other vm running sqlexpress. they run fine and I can connect to them using sqlexpress... but when i try to access from sqlserver... I get this error. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) Digging deep into the error, I found this Error Number: -1 Severity: 20 State: 0 and finally this... Program Location: at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj) at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart) at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup) at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) at System.Data.SqlClient.SqlConnection.Open() at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server) at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser() Firewall is turned off on the VM that's running mssqlserver... I turned of firewall on one of the vm that's running the sqlexpress but I still get the error... can someone please help... thank you

  Read the article

• Bandwidth Suggestion

  - by Campo

  I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

  Read the article

• Windows Server 2008 R2 - VPN Folder Sharing Permissions

  - by daveywc

  I have setup VPN access to my Windows Server 2008 R2 server using RRAS. Clients can connect, run applications, view shares etc. My problem is that one of the applications that they use relies on some network shares. The application is not able to access the shares unless the user first goes into Windows Explorer and accesses the share, providing their user name and password (the same one that they use to connect via the VPN). Previously on a different Windows Server 2008 (not R2) this was not necessary i.e. the application and user could access the share without providing another user name and password. I have tried giving the Everyone group full control over the shared folder - both on the Security tab and in the Permissions area under Advanced Sharing on the Sharing tab. This still did not resolve the issue. (I don't really want to give Everyone access anyway - I was hoping that granting access to a group that the VPN users had membership of would be enough). I have also turned off password protected sharing in the Advanced Sharing Settings area of the Network and Sharing Center (under both Home or Work and Public). So my question is what is preventing my VPN users from having access to these folders without having to re-supply the same login and password that they use to access the VPN? And what is the best practice in this type of scenario?

  Read the article

• Multiple WAN interfaces on SonicWall TZ 100?

  - by Chad Decker

  I'm using a SonicWall TZ 100 with a basic configuration of X0 for the LAN and X1 for the WAN. The WAN uses DHCP to obtain its routable IP address. I want to obtain a second routable IP from my ISP. I'm in luck because my cable company will provide me with an additional dynamic IP for $5/mo. How do I bind this IP to my SonicWall? My additional dynamic IP will not be consecutive to the original one. It won't even be on the same class C. I think what I want to do is to use one of the empty ports/interfaces (X2, X3, or X4), tell that interface to use DHCP, and then add that interface to the WAN "zone". I can't figure out how to do this though. Here's what I've tried so far: (1) I've looked in Network Interfaces. I see X0 and X1 but the other unused interfaces don't show up. I don't see an "Add" button to add the new interfaces. (2) I've looked in Network Zones. I see that X0, X2, X3, X4 are in the LAN zone. I tried to drag X3 into the WAN zone but I can't. Nor does clicking the "Configure" button allow me to move an unused interface from LAN to WAN. (3) I've read the post entitled Splitting up multiple WAN's on Sonicwall. This doesn't seem applicable to me. Any thoughts?

  Read the article

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• SSH works in putty but not terminal

  - by Ryan Naddy

  When I try to ssh this in a terminal: ssh [email protected] I get the following error: Connection closed by 69.163.227.82 When I use putty, I am able to connect to the server. Why is this happening, and how can I get this to work in a terminal? ssh -v [email protected] OpenSSH_6.0p1 (CentrifyDC build 5.1.0-472) (CentrifyDC build 5.1.0-472), OpenSSL 0.9.8w 23 Apr 2012 debug1: Reading configuration data /etc/centrifydc/ssh/ssh_config debug1: /etc/centrifydc/ssh/ssh_config line 52: Applying options for * debug1: Connecting to sub.domain.com [69.163.227.82] port 22. debug1: Connection established. debug1: identity file /home/ryannaddy/.ssh/id_rsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_rsa-cert type -1 debug1: identity file /home/ryannaddy/.ssh/id_dsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_dsa-cert type -1 debug1: identity file /home/ryannaddy/.ssh/id_ecdsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.0 debug1: Miscellaneous failure Cannot resolve network address for KDC in requested realm debug1: Miscellaneous failure Cannot resolve network address for KDC in requested realm debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP Connection closed by 69.163.227.82

  Read the article

< Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >