Search Results

Search found 12605 results on 505 pages for 'settings'.

Page 410/505 | < Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• Host ::1 resolves to remote IP

  - by thebuckst0p

  /etc/hosts files usually have this line, ::1 localhost. I thought ::1 was the equivalent of 127.0.0.1/localhost, and from my reading it seems to be the IPv6 version. So I was using it in Apache for firewalling, "Allow from ::1" and it only allowed local. Then suddenly that stopped working, so I pinged ::1 and got a remote IP address. I tracerouted it and it went through my ISP, through some Microsoft server, then another half dozen steps of asterisks... I'm not sure why this would be (the remote IP), but it doesn't seem good. I grep'd my hard drive for the remote IP and it doesn't appear anywhere. Is this some indicator that I'm being hacked, or normal behavior? Maybe my IPv6 settings are wrong? (This is a brand new MacBookPro with Snow Leopard.) Any ideas about this would be great - what is ::1 supposed to be, why would it be remote, should I be worried, how do I get it back to localhost? Thank you!

  Read the article

• SQL Server Installation: Is it 32 or 64 bit?

  - by CapBBeard

  Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

  Read the article

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• Games, Windows 8.1 and 144Hz display

  - by Marioysikax

  So I have been having problems with few games after switching from 7 to 8.1, which seems to be related to my 144Hz monitor. Few examples: Shank, Shank 2, Blood of the Werewolf, Astebreed, the Sims 2 and Rayman Legends patch 1.2Had few other as well but it's been long and I have 600+ steam library. From those games at least the Sims 2 and Shank worked without any problems with same setup and Windows 7. So basically these games simply refuse to launch with basic setup. However if I plug 60Hz TV with HDMI instead everything magically starts to work. As for Astebreed and the Sims 2 using windowed mode seems to also work. As for Rayman Demo and version 1.0 works for some reason and 1.2 breaks settings menu. I have already tried contacting supports. EA support stated game simply shouldn't work with 8.1 at all (which is lie as it works with that TV and friend with 8 plays just fine), ubisoft support took few weeks and support said he will forward info for further processing, blood of the werewolf support had no idea what's going on and told me to just use my TV instead.Changing monitors refresh rate to 120Hz or forcing it to 60Hz doesn't do anything. I have DVI right now but I will try with DisplayPort when I get the cable. At PCGW Garrett said it may have something to do how listing resolutions work with 8 compared to earlier Windows versions but my googling skills don't bring anything up and compatibility mode for earlier windows version doesn't work either (not that I expected that to work). My system specs are on my steam profile. How do I get those work with my 144Hz monitor as well as possible future games having same problem? Downgrading to 7 would work but is far from practical and I don't own legit lisence for that one.

  Read the article

• Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

  - by Josh Stodola

  So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

  Read the article

• Thunderbird 11.0.1 and Lightning 1.3: How do I propose a different time for a meeting?

  - by seaao

  This all happens on my x64 Linux workstation btw. tl;dr: My colleague invited some people and me for a meeting. The meeting was scheduled a week to late. I -wrongfully- accepted. How do I propose a new time? To explain a bit more in detail: I received a meeting request in my mailbox. Thunderbird is so nice to let me accept or reject it, and after I click the button to accept, it is directly added to my calendar. But when I double click on the meeting to edit it, I get a function-wise scaled-down version of the meeting: The only settings I can alter are whether I want reminders, and if I go at all. Trying to drag it to another day doesn't work either: My calendar behaves like read-only (which it isn't btw). There are several questions (without answer...) to be found on Stack Overflow and on the Thunderbird knowledge base about using lightning. But I get the idea that I'm one of the few who won't comply with the team even before the meeting is started. My googling revealed no bugs or feature requests in the direction I'm thinking. A link to an explanation how to achieve this, or another perspective about how to reach the desired goal (meeting with my colleagues and me) would be mostly welcome!

  Read the article

• Fedora installed in Legacy mode, how to make it work in UEFI?

  - by TryntaLearn

  I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

  Read the article

• Unable to load Windows after using EasyBCD to Reset bcd [duplicate]

  - by johnny

  This question already has an answer here: How can I repair the Windows 8 EFI Bootloader? 9 answers My windows installation was working perfectly fine until i clicked "Reset BCD" in EasyBCD in Windows 8. After clicking that EasyBCD told me to add Win 8 entry via Add Entry Menu so i did. After restart, win 8 would not start. Neither would recovery F11. Attempts i made to Restore : Ran boot-repair from ubuntu live cd several time. Used Win8 system recovery disc created via virtualbox with win 8 preview iso. Automated repair from Win8 system recovery disc Ran following commands from cmd started from Win8 system recovery disc bootrec /fixmbr Result : Success message bootrec /rebuildbcd Result : after hitting (Y) "The requested system device cannot be found" System refresh started from Win8 system recovery disc gives error that device is locked. System reset started from Win8 system recovery disc gives error that required partition or device is missing or not accessible. Used automated repair from EasyRE disc. It gave success message. Used Fix boot problem from Macrium reflect winPE repair disc. Copied Recovery partition to usb. Booting from usb gave this error Your PC needs to be repaired. Error Code : 0XC000000f Press Enter to try again Press F8 for Startup Settings F8 & Enter does nothing I cannot install WIn7 or Win 8, error it gives : "windows cannot be installed on this disk. The selected disk is of the GPT partition style."

  Read the article

• How do I configure VMware View location-based printing to use Active Directory Groups?

  - by Jason Pearce

  I am attempting to configure VMware View 4.5's Location-Based Printing, which leverages an included OEM version of ThinPrint, to assign printers to active directory groups. The location-based printing feature maps printers that are physically near client systems to VMware View desktops. I am using the Active Directory group policy setting AutoConnect Location-based Printing for VMware View, which is located in the Microsoft Group Policy Object Editor in the Software Settings folder under Computer Configuration. The AutoConnect Location-based Printing for VMware View appearst to be just a name translation table. It permits me to assign a specific printer or printers to an IP Range, Client Name, Mac Address, User, or User Group. I'm attempting to assign printers to active directory user groups. I have created a new active directory group for each printer that I intend to use in VMware View desktop pools. I will then assign active directory users to the active directory groups that represent each network printer. Example: doej is a member of the PTR-FLOOR2-NORTH-ROOM255 active directory group. Using AutoConnect, I assigned the group to receive a network printer by adding PTR-FLOOR2-NORTH-ROOM255 in the User/Group column. Problem: When doej logs in to his VDI session, the printer is not present. However, if I use a wildcard "*" in the User/Group column instead of the specific PTR-FLOOR2-NORTH-ROOM255 active directory group, the printer is present and functions as designed. Alternatives: I have tried assigning printers to active directory groups within AutoConnect in the following ways, all unsuccesfull: PTR-FLOOR2-NORTH-ROOM255 domainexample\PTR-FLOOR2-NORTH-ROOM255 domainexample.local\PTR-FLOOR2-NORTH-ROOM255 Confirmation: The information used to map the printer to the VMware View desktop is stored in a registry entry on the View desktop in HKEY_LOCAL_MACHINE\SOFTWARE\Policies\thinprint\tpautoconnect. For each of these examples, I have reviewed the registry entry and can confirm that the desktop is receiving the information from the AutoConnect translation table. Summary: Can anyone provide an example of how to configure VMware View 4.5's Location-Based Printing so that I may assign network printers to active directory groups via the included AutoConnect tool? I would welcome a clear example of a working configuration. Thank you.

  Read the article

• Hard Drive Compatibility with Motherboard

  - by Wesley

  Here are the current specs to put things in context: ECS P4VXASD2+ V5.0 Intel Pentium 4 Northwood 2.8 GHz 2x 512MB PC2100 DDR266 SDRAM Maxtor DiamondMax 10 250 GB PATA (IDE) HDD Gigabyte 52x CD-ROM NVIDIA TNT2 Pro 16 MB OKIA 300W ATX PSU USB bracket Modem PCI Before, I actually had a 300 GB hard drive installed. However, I read the FAQ for the motherboard and discovered that a maximum of 250 GB hard drive was supported. So I ended up finding the one listed above and put that in. However, upon booting up, I reset the BIOS to defaults and auto-detected all the drives installed. The 250 GB came up as something like 251.0 GB. I didn't think much about it until I tried to boot up a Windows XP installation disc. It booted up successfully and run for about a minute before the computer randomly rebooted. I've made sure that all the jumpers and settings are correct and everything has been installed correctly. I've tried running it without the addons and one stick of RAM but still the same thing. What else could be causing this problem?

  Read the article

• Lion MacBook Pro will not load webpages with DNS just after wake

  - by NReilingh

  I'm working with a 2011 MacBook Pro running Lion (10.7.2), that after waking from sleep (i.e. opening the lid) takes an inordinately long amount of time (2-3 minutes or more) to get a usable internet connection. Upon waking, the wi-fi icon signifies it is negotiating a network connection, and completes one a few seconds later. At this point, network diagnostics will not show any issues, and everything in Network preferences looks as normal: I'm connected to the proper network, have the right IP address and gateway, and DNS settings are correct. However, any site accessed with a domain name (like http://www.google.com) in Safari will return the "You are not connected to the Internet." error. Accessing a site directly, say, with Google's 74.125.226.212, is successful. Yet, Network Diagnostics will insist that DNS is functioning properly. After a few minutes, the following lines will be printed to the Console log, and regular behavior will be restored. 11/18/11 8:11:31.288 PM airportd: _doAutoJoin: Already associated to “Wireless”. Bailing on auto-join. 11/18/11 8:11:32.000 PM kernel: en1: BSSID changed to 00:25:9c:63:91:bd This behavior occurs only when waking from sleep--not when turning wi-fi on and off. This problem also occurs when using a wired Ethernet connection. As per this thread, I have tried flushing the DNS cache and wiping the wireless network from memory (it's not a protected network). Neither have worked.

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• Windows Vista/7 dropping Mac Server share points

  - by Hooligancat

  My Windows Vista and Windows 7 clients are having problems maintaining access to SMB shares on a Mac server. The initial connection to the server appears to be OK, as the Windows clients can see all of the server share points. However, the client randomly drops a couple of the server share points although the clients can still see the server. For example. If I have the following share points on the Mac server: Share A Share B Share C Share D Share E The Windows client can see these shares most of the time and can access them most of the time. But randomly a couple of the shares will just get dropped or go missing from the Windows client's ability to view them so I end up with something like: Share B Share D Share E All the share points are established int the same way with the same permission settings. My Mac OSX Server is set up with the following for SMB: SMB sharing enabled Standalone Server Workgroup of `CORPORATE` Allow Guest Access = YES Client connections limit = 100 Authentication: NTLMv2 & Kerberos and NTLM Code Page is Latin US (437) This is a workgroup master browser WINS registration is set to Enable WINS server (tried with setting off) Enable virtual share points for homes YES I noticed in my SMB file service log that the clients appear to connect OK, but I get the following error which implies a reset by either the server or the client: /SourceCache/samba/samba-187.9/samba/source/lib/util_sock.c:read_data(534) read_data: read failure for 4 bytes to client 192.168.0.99. = Connection reset by peer I am a bit stumped as to a direction to turn to try and get this to resolve. Continued attempts to access the server from the client will reconnect to the share points, but they inevitably get dropped again in the near future. Any and all help much appreciated.

  Read the article

• Xen Bridge only working when IP Assigned

  - by m.sr

  Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

  Read the article

• Switching from Onboard intel to Nvidia Dedicated GPU

  - by Anarkie

  How can I switch from Intel onboard grpahics to Nvidia Dedicated GPU? When I go to windows screen resolution I see intel. I cant change it. I go to Device Manager, I see both Adapters are there and Nvidia is known.I disabled intel, I didnt see any option to set one as primary so I disabled intel, black screen!Reboot and re-enable intel. I right click on the desktop, choose "Nvidia Control Panel" and on 3D options I chose the desired game I want to play, High performance Nvidia, but it didnt switch when I started the game. Then I made preferred GPU in the global settings High performance Nvidia for everything it still didnt change.I understand to save the battery etc. there is a switch option between these two but I dont see this switch when it is necessary, I cant also switch manually?Is there a manual switch FN key?I looked but couldnt find. Why I want to do this? 1) Better game peformance. 2) I want to play an old game from 2002(Diablo 2 LOD), when I start the game there are black bars on the sides, so screen becomes just smaller which I dislike!I heard this is intel's specification to center the display.But instead I would like to scale or expand it to fit widescreen(fullscreen).Which should be possible with Nvidia. My Notebook Specs: Fujitsu Lifebook AH531, Win7 , 64 bit, i5, intel HD graphics onboard, Nvidia GT 525. I didnt install Nvidia later, it was always installed and ready from the moment I turned on the computer first time. How I determined that the cards werent switched when I am playing the game: with the windows key I exited from the game, then looked at screen resolutions menu, still saw intel, also the game was still with black bars.I know intel GPU should enough for Diablo 2 but I am interested in this answer for further games, I dont always play Diablo, what if I install an up to date game for example?Then Intel will not be sufficient.I would like to learn the switch option.

  Read the article

• Postgresql connection refused

  - by Jonathan

  I'm trying to remotely connect to my postgresql database. I have two virtual machines set up both running ubuntu 14.04. I am trying to connect to the second vm using the first vm using psql -h 10.0.1.23 -U postgres -d postgres But I receive the error: Could not connect to server: Connection refused Is the server running on host "10.0.1.23" and accepting TCP/IP connections on port 5432? I have changed the pg_hba.conf and added host all all 10.0.1.64/24 md5 host all all * md5 host all all 0.0.0.0/0 md5 And changed the postgresql.conf listen_address=" * " In an attempt to allow all incoming connections. I have also tried to change the firewall settings, but I am unsure of whether or not the ports are properly listening for the connection. Edit: Output of netstat -an | grep -E '^tcp[^6].*LISTEN' tcp 0 0 127.0.1.1:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN

  Read the article

• Simple vLAN setup

  - by Logan Bissonnette

  I have a basic lab environment set up to try and get 2 vLANs working in hyper-v. I have the following equipment 1 hyper-v server 1 Desktop PC 1 Managed Switch (d-link DES-3052P) 1 cheap router (DI-604) My end goal is to have 1 VM and the desktop on one vLAN with internet, and 1 VM on a separate vLAN with internet access. I am having troubles getting an internet connection to both vLANs. The switch does not have the ability to have asynchronous vLANs. This is my switch configuration Port 1 - Trunk Port - Connected to router Port 2 - Trunk Port - Connected to hyper-v Server Port 3 - Access Port- Connected to Desktop Within hyper-v I have 1 switch and 2 VMs. When the VMs are set up to use vlan ID 1, everything works fine. As soon as a VM is set up to use vlan ID 2, they lose all network connection and cannot communicate with the router anymore. I believe this is because the router is not vLAN aware. Can anyone help me with what settings need to be set up on my switch? I believe I want an egress rule so traffic leaving towards the router is untagged, is that right? If not, any ideas or hints as to what needs to be set up?

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  Hiya, I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• iTerm2 vim cannot map alt key

  - by Eddy

  I'm having trouble trying to map the alt-key bindings on vim in iTerm2. I want to map shortcuts for switching between buffers like this: map <A-Right> <C-w>l map <A-Left> <C-w>h map <A-Down> <C-w>j map <A-Up> <C-w>k But I can't get it to work. I've tried everything, setting the option key as "Normal", "Meta" and "+Esc" in the profile settings. I've tried <M-Right> and <T-Right> but those don't work either. There are posts on superuser and stackoverflow but they use the old version of iTerm2 (v0.x). The only things I've managed to get working are <T-up> and <T-down>, or when I just use Macvim. I'm using iTerm2 v1.0.0.20120203, and Mac OS X 10.7.5 on a Macbook Pro.

  Read the article

• kde dropping keyboard

  - by shabbychef

  I am having problems with KDE 'dropping' my keyboard. It happens periodically when using my gentoo box directly, but has become much worse when accessing via NX (from a Mac laptop). Some possibly irrelevant clues: it appears to happen more often when the system is under higher CPU load the mouse continues to work, but no windows will accept any kind of keyboard focus. kwin will not accept tabbing between windows. when working on the machine directly, I can ctrl-alt-F1 to get to a shell (obviously this does nothing over NX). so I think it is KDE and not xorg. am running kwin-4.3.5-r1, and KDE-4.3.5 generally. this problem definitely appeared after upgrading to kde-4.x, but I do not remember if it appeared in kde-4.2. sometimes the keyboard will reappear, but sometimes I have to kill my kde session. playing with accessibility options or window-focus-stealing options in system-settings under kde will often make the keyboard responsive again, only to drop it perhaps minutes later. I had read online this might be an evdev problem under X (again, I think this is KDE, not X, but will try anything). as a result, I have fiddled with my xorg.conf endlessly. I even deleted it entirely and let nvidia-xconfig have a stab at it, with no luck I am tearing my hair out over this. I have done emerge -e xorg-server and am right now doing emerge -e kwin, to rebuild all packages that might be relevant. no luck with the xorg-server rebuild. any help appreciated. thanks,

  Read the article

• Is there any way to limit the turbo boost speed / intensity on i7 lap?

  - by Anonymous

  I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

  Read the article

• Slow browsing through IE on Windows Server 2012

  - by Volodymyr

  We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

  Read the article

• Is it possible for the Subversion Apache module to serve html files with an html content-type without using the svn:mime-type property?

  - by Martin Pain

  I am aware that if you set the svn:mime-type Subversion property on a .html file to text/html then when viewing the file in a browser through the Subversion module in Apache httpd it will be served with a Content-Type: text/html header, enabling the browser to render it as HTML rather than plain text. However, I am looking for a way to do this without using the svn:mime-type property. I'm aware that you can configure your svn client to automatically add the property - this is not what I want, as I do not want to ensure all users have these settings. I'm also aware that I could create a pre-commit hook that rejects the commit if the properties are not set, in order to force users to set the property - I might fall back to that, but I'm looking for something less intrusive. I'm also aware that I could use a post-commit hook to add the properties automatically on the server-side. I'd rather not do that (as users then have to update immediately after their commit, and it's not trivial to write) - I'm looking for a better alternative. Perhaps something with rewrite rules in the Apache server?

  Read the article

< Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >