Search Results

Search found 12055 results on 483 pages for 'password complexity'.

Page 415/483 | < Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >

• Problem creating ODBC connection to SQL Server 2008 with Vista

  - by earlz

  Well, I'm trying to get a database schema thing working, first I tried just doing it in Linux where I'm more comfortable, but ODBC seems to be a hack there and I couldn't get it to work. So I figured it shouldn't be too hard in Windows.. Ok, so I created a SQL Server Client Alias so that I can simply same windowsserver to refer to my SQL server. Then, I went to the ODBC configuration in Control Panel. I clicked Add in the User DSN section. I chose Native SQL Server (10), and then clicked next. Then I typed a short name and a description and gave the servername as windowsserver/SQLEXPRESS Then, I click next, give it my user name and password and click next. Then, after like 2 minutes it says "Login Timeout Expired" What can be wrong here? I know the server is configured cause I have SQL Server Management Studio opened up with that server in it. I'm also just trying to connect over regular TCP/IP and my firewall is disabled.

  Read the article

• Curious enigma of a network cable / connection / quality

  - by Foo Bar

  So, the situation is like this: I'm renting an apartment in a large house and I'm sharing internet with the landlord who lives downstairs. The internet is (in my best guess) optical 20/20Mbit. I don't know how it's all wired in his flat (haven't been there / seen it). Anyway, in my flat comes a cable which seems to be connected directly to the optic to ethernet router (and the password is the default one, so I have access, he he). There was a switch connected to that and to wires that go around the flat, and the wiring is terrible. It's even mixing phone and ethernet, and from what I see some cables are even interconnected!? Anyways, this cable that comes to my flat is very short. I can barely connect my computer on it, but if I do, I seem to get decent speed / performance. Not great, but decent. If, however, I connect switch to it (tried 2 different switches and a wifi switch) it's all blinking but I can't even connect to 192.168.1.1 (the router). DHCP fails, ping is losing 80-100% of replies. So I connected this cable directly to the other cable which goes to my work room, with a connector that has two female jacks and no electronics. Now when I connect my computer in my room, again, the performance is decent. When I connect WRT54GL (with tomato, DHCP disabled) to it and I plug a cable in this WRT and to my computer... the performance is gone. Download seems okay on Speedtest, but upload is .2Mbps and it's connecting forever. So what kind cable troll am I having here? Any ideas?

  Read the article

• Why does my computer sometimes not identify my wireless network, or others, that it always connects to?

  - by Emile Erasmus

  I have a vista operating system. Sometimes my computer will not connect to the wireless network (internet) when I start up my laptop. This happens at different places on occasion, and it is very random. It tries to connect, but can not identify the network (it does recognize the wifi name). So at the end it connects, but with limited connectivity. It can not be the hardware because all other computers connect to it fine at the same time. And it happens at different places, mostly home, but sometimes at coffee shops, etc. And then in a day or two when I start up my laptop it is all of a sudden working again. (restart does not solve the problem). I have tried all the trouble shooting options windows offers, restarting the notebook, switch modem on and off, switch laptop wifi on and of, deleted the wifi memory from the laptop and reconnected with the password as if it was the first time, everything. If it does not work at one place it does not mean it won't work at another. Example it won't work at home, then I go to coffee shop and it works, then get back home and it don't. Anyone encountered this before?

  Read the article

• MySQL permissions error when showing databases

  - by Tony

  I was trying to install homebrew and very very stupidly did this: sudo chown -R $USER /usr/local The Homebrew instructions say to do this and I'm not much of a sysadmin so I took their word for it. Lesson learned (although I wouldn't really know how to test this...seems like an "undo" script would be super valuable here) Anyway, what is done is done, but now I get this error: $ mysql -u root -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 548 Server version: 5.1.33 Source distribution Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show databases; ERROR 1018 (HY000): Can't read dir of '.' (errno: 13) I tried chown-ing back to root with no avail. Does anyone know how I can fix this without reinstalling mysql? Optionally, if I have to reinstall mysql, how can I dump my databases without access to the command line so I don't lose all of my data. Thanks!

  Read the article

• Certificates in SQL Server 2008

  - by Brandi

  I need to implement SSL for transmissions between my application and Sql Server 2008. I am using Windows 7, Sql Server 2008, Sql Server Management Studio, and my application is written in c#. I was trying to follow the MSDN page on creating certificates and this under 'Encrpyt for a specific client', but I got hopelessly confused. I need some baby steps to get further down the road to implementing encryption successfully. First, I don't understand MMC. I see a lot of certificates in there... are these certificates that I should be using for my own encryption or are these being used for things that already exist? Another thing, I assume all these certificates are files are located on my local computer, so why is there a folder called 'Personal'? Second, to avoid the above issue, I did a little experiment with a self-signed assembly. As shown in the MSDN link above, I used SQL executed in SSMS to create a self-signed certificate. Then I used the following connection string to connect: Data Source=myServer;Initial Catalog=myDatabase;User ID=myUser;Password=myPassword;Encrypt=True;TrustServerCertificate=True It connected, worked. Then I deleted the certificate I'd just created and it still worked. Obviously it was never doing anything, but why not? How would I tell if it's actually "working"? I think I may be missing an intermediate step of (somehow?) getting the file off of SSMS and onto the client? I don't know what I'm doing in the least bit, so any help, advice, comments, references you can give me are much appreciated. Thank you in advance. :)

  Read the article

• Ubuntu Server Wireless connection issue - replaced router but kept ESSID

  - by Stevo

  I have a ubuntu server 12.04 which was connected to my wireless network with no problem I replaced the wireless router but kept the ESSID and password the same. All other devices on network have connected correctly. However the Ubuntu Server will not route correctly. It will connect to the wifi router, and get a dhcp served IP address, however it will not route anything. I cannot ping the router from the server. the contents of /etc/resolve.conf are updated with the information from the router, (the host name has been served) I know there is nothing wrong with the router or the server, or the wireless card etc. I'm assuming there's some cached setting that associates the old router with the ESSID and causing the issue. I've got a lot of other devices connected to the router, so don't want to change the name of the ESSID. How do I fix this? EDIT: outputs (abbreviated as I've got no cut and paste) netstat -rn: Kernel IP Routing table Dest Gate Gen Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0. UG 0 0 0 wlan0 192.168.0.0 0.0.0.0. 255.255.255.0 U 0 0 0 wlan0

  Read the article

• How intrusive is using VPN?

  - by Slade

  My company lets us work from home sometimes using VPN (during weather emergencies and stuff). When logging in a big window comes up that says the network is private and for employees only and that there's no right to privacy while using VPN. It makes sense that they don't want people poking around their network but I wonder if the company can use the connection to look around my computer while I'm connected. I'm not entirely computer-illiterate but I'm not a networks person at all so the technical documents I've found don't help me. Is that possible, and if so to what degree? UPDATE Thanks Mark. The funneling thing is what I was really asking about. Mostly I was worried that I would already have some IM conversation open or log into eBay forgetting that the VPN was open and that my company IT people would see it or that they would log my eBay password. Thanks again. ANOTHER UPDATE What if my son wants to play online poker or Warcraft etcetera while I have VPN on to work? Can my company think I'm the one playing if I am not typing often?

  Read the article

• Mounting fuse sshfs fails when invoked by Cron on FreeBSD 9.0

  - by Tal

  I have a remote server filesystem that I'm attempting to mount locally on a FreeBSD 9 machine via FUSE sshfs, and Cron for a backup routine. I have ssh keys between the boxes setup to allow for passwordless login as the root user on the local machine. Cron is set to run the following script (in Root's crontab): #!/bin/sh echo "Mounting Share" /usr/local/bin/sshfs -C -o reconnect -o idmap=user -o workaround=all <remote user>@<remote domain>.com: /mnt/remote_server As root, I can run this script on the command line without issue, and without being asked for a password the share mounts successfully. Yet, when run by Cron the script fails. The path to sshfs is identical to the value of which sshfs Here is the email root receives from the Cron Daemon: X-Cron-Env: <SHELL=/bin/sh> X-Cron-Env: <HOME=/root> X-Cron-Env: <PATH=/usr/bin:/bin> X-Cron-Env: <LOGNAME=root> X-Cron-Env: <USER=root> Mounting Share fuse: failed to exec mount program: No such file or directory fuse: failed to mount file system: No such file or directory I'm stumped as to why I'm receiving No such file or directory in this instance. It further seems odd given that the paths appear to be correct. I've also attempted to compare the output of env on the shell with env inserted into the script. I don't see any environment variables that should cause this trouble. At bootup, FUSE reports its version as: fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8 Help me ServerFault wizards, you're my only hope!

  Read the article

• Powershell Script Scheduled Task Stopped Running (Could not Start)

  - by Hatsune Yuki

  I'm running a scheduled task (for Powershell Script) on Windows 2003 Server. I believe the script works fine. The task is scheduled to run every 10 minutes from 7:00am to 11:50pm everyday. However, it never gets to run more for than a day. It always stops some time in the afternoon (between 2pm and 6pm). I'm not sure exactly what happened but I always get the error The attempt to log on to the account associated with the task failed, therefore, the task did not run. The specific error is: 0x80070569: Logon failure: the user has not been granted the requested logon type at this computer. Verify that the task's Run-as name and password are valid and try again. It seems like most people with this error are saying that they need to make user "logon as a batch job". However, this option is greyed-out for me. I search for other places where users have similar problems but the solutions are not written in detail (some of them have something to do with GPO). I've only used the basic features of Windows Server and I have no clue how to get to the place they are referring to. Can someone please confirm whether "logon as a batch job" is indeed a solution and provide a detailed walkthrough on how to solve my problem? Thanks. p.s. someone suggested the website http://technet.microsoft.com/en-us/library/cc755659(v=ws.10) I tried to followed the method for web server with domain. However, got stuck on the 6th step where it mentions Group Policy Object. I don't know where it is.

  Read the article

• sudoer scheme to allow useful access to another web developer yet retain future control of a virtual

  - by Tchalvak

  Background: Virtual Private Server I have a virtual private server that I'm looking to host multiple websites on, and provide access to another web developer. I don't care about putting too many constraints on him, though I wouldn't mind isolating the site that he'll be developing from other sites on the server that I will develop. The problem: retain control Mainly what I want is to make sure that I retain control over the server in the future. I want to reserve the ability to create/promote/demote and other administrative functions that don't deal with web software. If I make him an admin, he can sudo su - and become root and remove root control from me, for example. I need him not to be able to: take away other admin permissions change the root password have control over other security/administrative functions I would like him to still be able to: install software (through apt-get) restart apache access mysql configure mysql/apache reboot edit web development configuration type files in /etc/ Other Standard Setups would be happily considered I've never really set up a good sudoers file, so simple example setups would be very useful, even if they're only somewhat similar to the settings that I'm hoping for above. Edit: I have not yet finalized permissions, so standard, useful sudo setups are certainly an option, the lists above are more what I'm hoping I can do, I don't know that that setup can be done. I'm sure that people have solved this type of problem before somehow, though, and I'd like to go with something somewhat tested as opposed to something I've homegrown.

  Read the article

• can't register a soft phone to asterisk11

  - by Tom

  I have a VM (on oracle vbox) running Fedora17. I've installed asterisk 11 on it from sources. I've followed the wiki for installation (https://wiki.asterisk.org/wiki/display/AST/Creating+SIP+Accounts) to the letter. The ip on the VM machine running fedora is 192.168.1.7 and I can ping it from the host machine (Ubuntu 12.04), which is at 192.168.1.2 I've tried registering with ekiga with the following settings: user: [email protected]. Password: verysecretpassword registar: 192.168.1.7 but I'm getting an error "transport fail". Also, while trying to register I'm logged in to the asterisk CLI with verbose level 3 and debug level 4 and nothing appears. some more relevant data: I've added the following code to the end of my sip.conf.sample file: [demo-alice] type=friend host=dynamic secret=verysecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 [demo-bob] type=friend host=dynamic secret=othersecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 After I changed the sip.conf.sample file, I've created a copy of it and named it sip.conf. then I logged in to the asterisk CLI and typed sip reload. Then I'm trying to register and ekiga client from my host machine at 192.168.1.2 but it doesn't work and nothing appears on the asterisk CLI while in verbose mode level 3. BTW, If there is missing information about my question, please don't close it. comment about what you need to know and I'll edit it in to the question. tnx.

  Read the article

• Is there any way to synchronize AD users with Office 365 but still be able to edit them online?

  - by Massimo

  I'm performing a migration to Office 365 from a third-party mail server (MDaemon); the local Active Directory doesn't include any Exchange server, and never had any. We will need directory synchronization in order to enable users to log on to Office 365 using their domain credentials; but it seems that as soon as you enable directory synchronization, you can't perform any action anymore on Office 365 users: all changes need to be made on the local Active Directory, and then replicated by the synchronization process. For ordinary users with a single e-mail address and standard features, this is not a big problem; but what about users which need an additional address? What if I need to configure some nonstandard setting, like "hide from address list" or a custom mailbox quota? From what I've gathered, the only supported way to do this, as you can't directly edit Office 365 objects anymore after synchronization is enabled, is to extend the local AD schema with Exchange attributes, and then manually edit them (!). Or, you can install at least one local Exchange server, and then use the Exchange administrative tools to configure the required settings. Is this correct or am I missing something? Is there any way to synchronize user accounts and password, but still be able to edit user settings directly in Office 365? If not (everything really needs to be set locally and then synchronized), is there any simpler way to do this than manually editing LDAP attributes or installing a local Exchange server?

  Read the article

• Compatibility of Fedora install on a Hybrid drive

  - by kjh

  I recently bought un ultrabook with a 500gb/32gb sdd hdd hybrid drive, and I'm having trouble replacing windows on it with fedora seventeen. it errors out saying there was an unhandled exception. Is linux compatible with hybrid drives? or can the operating system on a hybrid drive not be replaced? Edit: here are the steps I select special storage devices because it ignores my hard drives otherwise at this point i get the message: "Disk contains bios raid meta data, disk sda will be ignored" I can pick a hostname, select my timezone and set a password at the install type screen, no matter what I select (use all free space, replace linux systems, create custom partition etc..) once I click next, it says "an unhandled exception" has occured. and I can no longer proceed with installation. Here is the error message: anaconda 17.29 exception report Traceback (most recent call first); File "/usr/lib64/python2.7/size-packages/pyanaconda/bootloader.py"; line 183 self.stage1_drive=self_drives[0] File "/usr/lib64/python2.7/site-packages/pyanaconda/rw/cleardisks_gui.ph"; line... and tons of more lines like that

  Read the article

• Packet flooding while configuring a Debian L2TP/IPSec client?

  - by Joseph B.

  I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

  Read the article

• moving files and directories between two machine, via a third, preserving permissions and usernames

  - by Jarmund

  The situation is as follows: Machine A has a file repository accessible via rsync Machine B needs the above mentioned files with all permissions and ownerships intact (including groups etc) Machine C has access to both A and B, but has a completely different set of users. Normally, i would just rsync everything over, directly between A and B, but due to severely limited bandwidth at the moment, i need something different, as rsync times out after building the list of the 430 files (49Mb uncompressed... can be compressed down to ~7Mb). What i've tried so far: rsync everything over from A to C, tar it, copy the tarball over, and then untar it, however, this messes up the ownership and/or the permissions. To rsync it from A to C, i run this command: rsync --numeric-ids --password-file=/root/rsync_pwd_file -oaPvu rsync://[email protected]/portal_2/ ./portal_2/ ...and from the looks of things, they do end up on C with the correct ownerships/permissions/flags/everything (not 100% sure, though.. are there any more switches i can throw in there? did i miss something?) copying the tarball over is simple enough (slow as a one-legged turtle due to the bandwidth, but it checksums out alright) What i'm unsure of is the flags and switches for creating and extracting the tarball, so could someone please provide the full commands for creating a tarball from /root/portal_2 on machine C (with everything intact) and extracting the tarball into /var/ex/portal_2 on machine B? ? Also, are there any other approaches worth mentioning that could allow me to perform this? I have root access to A and C, whereas i only have rsync access to B. PS: I'm running rsync v2.6.9 on machine B, and unfortunately i do not have the oportunity to upgrade to v3

  Read the article

• Apache directory access with virtual host

  - by alexeygaidamaka

  I have a virtual host with a configuration like that. When i'm trying to get into foobar.com/dir providing valid username/password pair i get 403 forbidden page instead of that directory contents. www.foobar.com/dir has 777 rights, .httpaswd is chmoded 644. But i can't figure out why i am still not seeing contents. Please, give me a hint. ServerAdmin webmaster@localhost ServerName www.foobar.com ServerAlias www.foobar.com DocumentRoot /var/www/foobar <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/foobar> Options -Indexes FollowSymLinks AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> <Directory /var/www/foobar/dir> AllowOverride AuthConfig AuthName "Authorize yourself, please!" AuthType Basic AuthUserFile /etc/apache2/.htpasswd AuthGroupFile /dev/null Allow from All Order Allow,Deny Require valid-user

  Read the article

• Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

  - by DOTang

  I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

  Read the article

• Issues connecting to HP ProCurve switches

  - by BriGuy

  We are having a very strange issue trying to connect to our infrastructure switches via SSH. When you first try connecting to them, the switches will prompt for the password - and then just sit there after it is entered. If you create a second SSH session to the switch (while letting the first one remain open and just sitting there) it will let you log right in. The switches are doing the same thing with RADIUS and local authentication. The other strange part to all of this, is that about 10 switches started doing it all at the same time. As far as actual configuration of the switches, nothing has changed. Occasionally, one switch will start working like normal, but then stop again. These are all HP ProCurve managed switches, but all different models/firmware. Some switches that are not working are using the same firmware as others that are working. UPDATE: 20130312 I am also seeing this same behavior when trying to use telnet. The first telnet session just hangs there, and the second telnet session will let me log in. Rebooting the switches seems to get them working, but I still have 5 production switches that cannot easily be rebooted because of their production roles. Is anyone aware of anything else that can be switched on/off that may reset the logon for remote management or something like that?

  Read the article

• Powershell Get-Process cannot connect to remote computer

  - by amandion

  I've been struggling with this for a few hours and can't figure this out. I have two Windows 7 computers. One is my workstation that is using Powershell to do administrative maintenance. The other is the machine I'd like to use Powershell remoting on to execute remote Powershell cmdlets on. On both computers, I've enabled Powershell remoting and added all computers to TrustedHosts with the * value. On the remote computer, I've started the Remote registry service and ensured that the DCOM, Winmgmt and the Winrm services are running. Firewall is disabled on remote machine too. The cmdlet I try to run is: Get-Process -ComputerName $name Where $name is the name of the remote machine. I keep getting an error saying that it could not connect to the remote PC. I've also tried using the IP and I get the same error. These PCs are not in a domain. I am able to do the following successfully: Invoke-Command {get-Process} -ComputerName $name -Credential $creds Where $name is the machine name and $creds is the user name and password for the remote computer's local Admin account. This gives me the same output I would expect. While this is an acceptable workaround, I am curious, why doesn't using get-process with remoting work as it should? I've seen a few articles on the web suggesting people have had success with it on its own. Each time I am using Powershell on my workstation with elevated privileges. Any ideas?

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

• How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

  - by Kdansky

  At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

  Read the article

• How to know who accessed a file or if a file has 'access' monitor in linux

  - by J L

  I'm a noob and have some questions about viewing who accessed a file. I found there are ways to see if a file was accessed (not modified/changed) through audit subsystem and inotify. However, from what I have read online, according to here: http://www.cyberciti.biz/tips/linux-audit-files-to-see-who-made-changes-to-a-file.html it says to 'watch/monitor' file, I have to set a watch by using command like: # auditctl -w /etc/passwd -p war -k password-file So if I create a new file or directory, do I have to use audit/inotify command to 'set' watch first to 'watch' who accessed the new file? Also is there a way to know if a directory is being 'watched' through audit subsystem or inotify? How/where can I check the log of a file? edit: from further googling, I found this page saying: http://www.kernel.org/doc/man-pages/online/pages/man7/inotify.7.html The inotify API provides no information about the user or process that triggered the inotify event. So I guess this means that I cant figure out which user accessed a file? Only audit subsystem can be used to figure out who accessed a file?

  Read the article

• Configuring SQL Server Express 2005

  - by MrTognio

  What's the proper way to configure SQL Server Express 2005 so that it can allow for a number of clients to get connected to the server? I have my application running both in the server machine and the client machines. Given the nature of my application, clients are the branches geographically distant from each other, and the server itself. Every operation the client records must be reported to the server, because the server needs total control over the usage and production. But, what should I consider when configuring the connection in both sides, the server and the client? I'm not as used to SQL Server, I'm a beginner, however through SQL Server Configuration Manager I have set the main options without success. The problem seems to be related to trusted connections even though I have set it to support both windows and SQL Server authentication. When the client tries to connect to the server using windows authentication it displays no table; when it tries to communicate using a password (SQL Server authentication), tables are successfully displayed but no access is allowed... Thanx in advance!

  Read the article

• What are the possible problems, when wget returns code 500 but same request works in normal browsers?

  - by markus

  What should I be looking for, when wget returns 500 but the same URL works fine in my web browser? I don't see any access_log entries that seem to be related to the error. DEBUG output created by Wget 1.14 on linux-gnu. <SSL negotiation info stripped out> ---request begin--- GET /survey/de/tools/clear-caches/password/<some-token> HTTP/1.1 User-Agent: Wget/1.14 (linux-gnu) Accept: */* Host: testing.thesurveylab.net Connection: Keep-Alive ---request end--- HTTP request sent, awaiting response... ---response begin--- HTTP/1.0 500 Internal Server Error Date: Wed, 12 Dec 2012 14:53:07 GMT Server: Apache/2.2.3 (CentOS) Set-Cookie: blueprint2-staging=8jnbmkqapl30hjkgo0u6956pd1; path=/ Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Strict-Transport-Security: max-age=8640000;includeSubdomains X-UA-Compatible: IE=Edge,chrome=1 Content-Length: 5 Connection: close Content-Type: text/html; charset=UTF-8 ---response end--- 500 Internal Server Error Stored cookie testing.thesurveylab.net -1 (ANY) / <session> <insecure> [expiry none] blueprint2-staging 8jnbmkqapl30hjkgo0u6956pd1 Closed 3/SSL 0x0000000001f33430 2012-12-12 15:53:07 ERROR 500: Internal Server Error.

  Read the article

• How best to handle end user notification in the event of system failure incl. email?

  - by BrianLy

  I've been asked to research ways of handling end user notifications when systems such as email are experiencing problems. Perhaps an example will make this a little clearer. We have a number of sites in different countries. Recently email was impacted at one of the sites, but it could have been a complete network outage. Information was provided by phone to local IT managers at the site but onward communication was slower than some would have liked. It seems like almost everyone at the site has a personal mobile phone which could receive text messages, and perhaps access a remote website with postings on the situation. However managing and supporting a system to text people on these relatively infrequent occasions would be very costly to do internally. What are other people doing to handle situations like this? Some things I've thought of include: Database of phone numbers to text. Seems costly and not very easy to maintain for an already stretched IT group. Is there an external service that would let you do this policies? Send voicemail message to all phones on site. Maintain an external website. This would not work in all situations (network failure), and there is a limit on the amount of info that can be posted externally. A site outage could be sensitive information in some situations. How could the site be password protected? Maybe OpenId/Facebook connect would work. Use a site like Yammer.com which is publicly accessible but only by people with a company email address. Anyone using this for IT outage notifications? To me it looks like there is no clear answer, and that there are solutions for some subsets of users. To be comprehensive a number of solutions would need to be combined. Any additional thoughts or recommendations? What worked or didn't work for your organization?

  Read the article

< Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >