Search Results

Search found 11478 results on 460 pages for 'disk partition'.

Page 418/460 | < Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >

• PHP unable to allocate memory.

  - by AlReece45

  On my way to the office this morning, every website on our shared VPS started giving the same error (several times, not the typical memory_limit error which is fatal): Warning: Unknown: Unable to allocate memory for pool. in Unknown on line 0 The shared server is a 64-bit OpenVZ container running cPanel. There are only ~6 VPSes on the host-- this is the largest one at only 4GB. The host itself has 24GB RAM. As the below graphs show, the memory usage on the host and VPS are both rather low. CPU Usage/Disk/Host all seem to be normal. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. Apache 2.2, PHP 5.2 (mod_php) Restarting Apache has corrected the problem for now. However, I'd like to prevent it from happening again and I'm not sure what was limiting the memory. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. There's seems to be plenty of memory: what caused this error? VPS Memory Usage Host Memory Usage APC Information apc.ttl=0 apc.shm_size=0 apc.mmap_file_mask=(blank) 1 Segment(s) with 32.0 MBytes (mmap memory, pthread mutex locking)

  Read the article

• Last step in HDD Recovery (fixing windows)

  - by Atom Computing

  My dad’s hard drive corrupted which was a result of many bad sectors. Anyway, I made a clone of the drive and have now repaired it totally (recreating the MBR and MFT) and doing a series of ChkDsk's on it. I can now see all the files and folder on it and it is all intact. I currently have it as a slave in my computer (where I was doing all the repairs). When putting it back into the computer, it comes up with "A disk read error occurred: Press Ctrl + Alt + Del to Restart". I don’t know why this is happening but think it might have something to do with file permissions. I have tried a start-up recovery on the Vista boot CD and it found no problems. When trying to apply file permissions (and creating file perms for the SYSTEM group (as it didn’t have any for SYSTEM group)) it couldn't apply them for some of the System32 folder files. I have tried applying them as admin and with as powerful privileges I can get. All to no avail. When it is in my PC I can boot it up (I added it into my bootloader) and it boots up fine except when it logs in it comes up with the error - "Rundll32.exe - Windows cannot access the specified device, path or file. You may not have the appropriate permissions to access the item" This message keeps coming back and nothing loads at all. Any help would be greatly received as I have got so far with the data recovery and want to avoid a reformat at all costs due to the vast number of programs installed and I don’t have much time on my hands! Thanks

  Read the article

• How to make Thunderbird play nice with Google mail

  - by Christi

  Thunderbird and gmail aren't exactly the best of friends. Gmail's tags mean that Thunderbird often downloads multiple copies of a single mail. Anything tagged in gmail will appear in a folder related to that tag, the "all mail" folder, and possibly the "inbox" and "sent mail" folders too. Thus a mail with multiple tags could potentially be stored more than four times in a local Thunderbird cache. This can make searching difficult, and is obviously wasteful of disk space. The best solution I have come up with is as follows. Operate a zero inbox policy (i.e. use the inbox for processing live mail only and archive everything else) which eliminates an extra copy in the inbox. Secondly, configure Thunderbird not to sync the "Sent Mail" folder - this is a bit of a pain, since I actually find it quite useful to be able to look through just the mails I've sent, but a search can duplicate this functionality. In this way, most of the duplicates are removed, and only mail with tags is stored locally more than once. Ideally, however, I'd only like one copy of each mail to be stored locally. I am surprised Thunderbird doesn't store mail by some sort of hashing algorithm to prevent precisely this problem - but it wouldn't be compatible with the way the folders are mirrored in a local directory structure, I suppose. Can anyone think of a better way to get Thunderbird to cache a Google mail account locally efficiently.

  Read the article

• Restore a database with LDF file only

  - by Martin

  First of all, i know how stupid it is not to have a any backup. I can't help it, but i have to (try) to solve it. I have a transaction log (LDF) file from a SQL Server 2000 database that contains all transactions since the creation of the database. No truncation has been done. The MDF file is gone. Probably because of some disk failure. There is no backup. Not from the original database and not from the transaction log. I have tried to link the transaction log to a new clean database. But (ofcourse) that failed because SQL Server checks the identity of both files. I have read about software that can read the transaction log. ApexSQL seems to do that. I tried to install the trial version but it gives weird errors when trying to start the program. Anyone knows a solution for me? It may contain third party software, but i prefer a clean SQL Server solution.

  Read the article

• Is it possible to to create a live linux iso containing a win xp virtual machine?

  - by mark

  I would like to have a Linux live system that contains a Windows xp virtual machine. This would be run from a bootable USB flash drive. My attempts so far have been unsuccessful. I created a Lubuntu 12.04 virtual machine with VMware. I updated and configured it to my needs, and installed Virtualbox. I then created a Windows xp vm with Virtualbox in the Lubuntu vm. I tested everything and everything worked, including USB devices. I installed Remastersys in the Lubuntu vm, copied the xp vm folder to the /etc/skel folder then created the custom iso with remastersys. I burned the iso and tested it on a laptop. It worked flawlessly. All programs and wireless networking worked. My problem was the xp vm. Virtualbox started fine but would not run the vm. I have the following error: Result Code: NS_ERROR_FAILURE (0x80004005) Component: VirtualBox Interface: IVirtualBox {c28be65f-1a8f-43b4-81f1-eb60cb516e66}. I ran remastersys again changing the permissions on the skel folder to R W for everyone. I also logged into Lubuntu as root and ran remastersys again. Each iso I created worked fine but would not start the xp vm inside. The last attempt virtualbox gave me an access error stating it can not access the virtual disk. Is what I want to do possible? In theory I don't see why it would not work. Is it a permissions issue? Should I create the iso then add the xp vm after by editing the iso by hand? Using a vm and not real hardware as a build machine a problem? Any ideas? keep any responses in laymens terms. I am still a Linux novice.

  Read the article

• Windows 8 install from USB freezes

  - by Rafael Almeida

  I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

  Read the article

• Fedora 19 no longer bootable

  - by Parisa

  I had fedora dual-booted with windows on my laptop for a while but with windows refresh grub was gone and my system directly booted windows. I booted fedora with my systems boot options and with this tutorial: https://fedoraproject.org/wiki/GRUB_2 I reinstalled grub2 but then had my system booted into an empty grub prompt: grub So I found the drive containing vmlinuz and initramfs (completely sure about thair location and versions) and tried to manually boot it but after the boot command it said: no suitable video mode found booting in blind mode and nothing happened. Such a tragedy... I have already tried to use live disks rescue system. Funny but troubleshooting options don't apear on my laptop while they do on my desktop pc. I cant even go to boot prompt on my lenovo idepad z400 laptop. I also tried EasyBCD so maybe I could boot it with windows but it comes up with this error: missing AutoNeoGrub().mbr Now I have removed the grub prompt (don't know why) and its really hard for me to reinstall my dearly customized fedora. If anyone knows a way to help boot it again or reinstall it keeping my files and installations I really need it. Thanks PS:I have already tried Boot-repair Disk but it asks me to enable the repo containing grub-efi on my fedora to reinstall the grub2 and fix the boot for me (how could i?).

  Read the article

• 100% CPU when doing 4 or more concurrent requests with Magento

  - by pancake

  Currently I'm having trouble with a server running Magento, it's unbelievably slow. It's a VPS with a few Magento installations on it used for development, so I'm the only one using them. When I do 4 request all 2 seconds after each other I'm finished in 10 seconds. Slow, but still within the limits of my patience. When I do 4 "concurrent" requests, however (opening 4 tabs in a row, very quickly) all four cores go to 100% and stay there for like a minute. How is this possible? I know that there are a lot of possibilities here, so any tips on how to make an Apache/PHP server go faster are also welcome. It used to go a lot faster before, and I've also tried APC, but it kept causing problems (PHP errors, something with memory pools) so I've disabled it. By the way, the Magento cache is off and compiling is also off. I know this makes Magento slower than usual, but I don't think a 60 second response time is normal for any Magento installation. Virtual hardware: 4 Cores and 4096MB RAM Swap is never used (checked with htop) 100GB disk space, of which 10% is in use Software: Debian 6 DirectAdmin and apache custombuild PHP 5.2.17 (CLI) If you need more info, please tell me how to get it, because I probably don't know how. I do know how to use the command line in linux and the usage of quite a few commands, but my experience with managing a server is limited.

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• maximum size filesystem on my test .... approach?

  - by jocco

  Hello all I'm new at the site, and I have a question. I got this question at a test and really like to know the correct approach to solving this problem? Here is the question. In an indexed filesystem the first indexblock (inode) has 12 direct pointers and 1 pointer to an indirect indexblock. The filesystem is implemented on a disk with a diskblock-size of 1024 bytes. All pointers are 32 bit. Question: what is the maximum filesize (Kilobytes) of this filesystem? If it's possible not an just an answer but an explanation. edit: It was a multiple choice btw with 4 answers a. 13 K b. 268 K c. 524 K d. 1036 K As for my approach I only got as far as to know that 1 pointer is 32 bit Also I found something else here on the site which seems very usefull. http://stackoverflow.com/questions/2755006/understanding-the-concept-of-inodes Ok i got this far There are 12 blocks and each block is 1024 bytes. 1024 * 12 = 12288 bytes or 12 KB directly accessible. Please correct me if I'm wrong. Each pointer is 32 Bit = 4Byte And to be honest at this point I'm starting to get confused especially since my answer is way over any of my multiple choice answers.

  Read the article

• System randomly freezes yet mouse still moves

  - by user784446

  This problem has lasted for the past 48 hours. The first time it happened, a program I was running stopped responding, so I tried to end it from task manager. The processes at first were listed fine until hovered upon. Eventually, despite the mouse still being able to move, after a few persisting clicks the mouse finally stopped moving. The screen went blank shortly thereafter. The second time it occurred, items on the screen stopped responding - hovering over the taskbar or such wouldn't elicit a response. Sound would still play however. Eventually, the mouse became unresponsive and the system restarted itself. I suspect that it may be a problem of my SSD drive. After looking through some Google search results, I downloaded HDTunePro to determine if there's a problem with the drive. Results returned a problem of reallocated sector count. An error scan also revealed 48 bad sectors. Also, an attempt to backup the contents of the most important areas of the drive returned a few explorer "Error: cannot read source from disk" errors. Should I ditch the drive and use another drive or is there anything that can be done to repair the drive? SSD: OCZ Petrol 64gb CPU: AMD Athlon II X4 640 RAM: Generic 3GB DDR2 Motherboard: Gigabyte MA74GM-S2H OS: Windows 7 Ultimate x64 Thanks!

  Read the article

• How to recover Windows Password without reinstalling if you forgot Windows password?

  - by user38908

  Usually, we can recover Windows admin password in two traditional ways. The first is to change Windows password with another admin account; the second is to recover the previous password with the windows password reset disk that had been created before you forgot the password. Take Windows XP for example, 1 At the Windows XP login prompt when the password is entered incorrectly click the reset button in the login failed window. 2 Insert the password reset diskette into the computer and click Next. 3 If the correct diskette Windows XP will open a window prompting for the new password you wish to use. However, we offen ignore the important of security until we have been locked out of computer. Fortunately, there is still the last way that can unlock your computer without reinstalling - erase Windows password with Windows password reset CD, which can recover admin password for Windows 7/XP/Vista/NT/2000/2003.... Take Windows Password unlocker for example, followings are the steps to create the reset CD 1.Download Windows Password Unlocker from Password Unlocker Official site 2.Decompress the Windows password unlocker and note that there is an .ISO image file. Burn the image file onto an blank CD with the burner freely supported by Password Unlocker. 3.Insert the newly created CD into the locked computer and re-boot it from the CD drive. 4.After launched the CD, a window pop up with all your account names(if you have several accounts) select one of the accounts that you have forgotten its password to reset it. Just one press, this software can remove Windows password instantly.

  Read the article

• Linux Centos 6 becomes unavailable from time to time - OS&network issue

  - by adoado0

  I am encountering following problem. There is one server (DL160 G5) running Centos 6.3 with default kernel 2.6.32-220.2.1.el6.x86_64 - at this point I'd like to add that issue appeared also at older version - 6.1 and older kernel (do not remember exactly which version). There is cPanel installed and from time to time it becomes unavailable (network connection). What I've checked is (via KVMoIP): load average is completely normal it does not lack memory or disk space when problem occurs no console notifications checked all access logs and there is no sign that it can be caused by a client script cannot even access local interface (127.0.0.1) or main IP address running tcpdump I can only see packets arriving to server - no responses all services seem to be running properly (mail,sql,http,ssh) checked crontab and all clients' crontabs too network port utilisation is low ( up to several Mbits) arriving packet rate is low - hundreds per second (according to tcpdump) console (via kvmoip) works fine, no lags there is no conntrack at this server there is no ipv6 at this server flushing iptables, unloading modules does not resolve problem restarting network does not resolve problem, no errors appear it also occurs when two sepearate networks are configured (and multiple gateways) as well as one IP, one default gw and one network is configured - so it seems network configuration independent it seems to repeat randomly (load,packet rate,bandwith usage,load independent) checked server with different rootkit detection tools - it seems to be clean server has been rebooted, it did not change anything there are no interface errors it apperas randomly can be once a week or several times per day It usually works fine after 1-15 minutes. What I can also check? It is definitely OS issue - there is traffic at interface only in one direction when problem occurs, can not even ping loopback. Any ideas? Recommended checks? Anything I did not checked above.

  Read the article

• Can I have a single solid state drive and a RAID array on the same machine? [closed]

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Is there a 'global media cache' in Windows 7 that may be used by third party media players?

  - by Pulse

  Here's the background. I don't use Windows Media Player or Media Centre, in fact both components have been 'turned off' via the 'Programs and Features' option. My media player of choice is a nightly build of MPC-HC, which plays virtually everything. I do, however, have VLC portable available for those rare instances when MPC-HC can't or won't play something correctly. This is the situation. I tend to download various media files via torrent, typically, game trailers or freely availably films, such as the recently released, torrent only, Pioneer One. Quite often these files are quite large, being 1GB+ so I quite often like to preview the file after it has downloaded a significant portion of the file. For the most part, this works quite well, and gives me an idea about the worth of continuing the download. Sometimes, however, the file doesn't play as expected and instead plays a completely unrelated file that has been previously played. Here's the strange thing. if I try to preview the file in MPC-HC or VLC both players play the same, previously played file, regardless of whichever player was originally responsible for playback. Most times, it's not even a file that's been played recently. I have searched the registry for some sort of MRU cache, but have found nothing. I have made sure each player has had it's respective history/cache deleted and can fine nothing on disk that seems to be storing this, apparently shared data. So, the question is, where are these unrelated players getting the file information from? Thnaks.

  Read the article

• Website latency and bad tcp packets

  - by Mistero Lupo

  I have multiple websites hosted on a Linode VPS and I'm having an issue with one of them: every page that I try to load has about 10 seconds latency. Apache logs are clean and the other websites on the same machine are running well. At a first glance I tought it was a memory problem since the VPS has got only 512M, but from the linode dashboard CPU and Disk I/O are normal. Anyway here we have the ram status: $ free -m total used free shared buffers cached Mem: 487 463 23 0 2 55 -/+ buffers/cache: 404 82 Swap: 255 155 100 Only 23M free, but if it was a memory problem why other websites are going as usual? I took a live capture with wireshark, and there are some duplicates SYN ACK packets just before the 10 seconds gap. I'm out of ideas, looking for some clues. Wireshark live capture screenshot As you can see from the image, the gap is after the last bad tcp. Thank you in advance. UPDATE I've checked Apache2 logs in debug error level, and this is where something is appening: 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'index.php' 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (1) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] pass through /home/fmaisi/sites/www.fmaisi.it/public_html/index.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] strip per-dir prefix: /home/fmaisi/sites/www.fmaisi.it/public_html/wp-content/plugins/wp-filebase/wp-filebase_css.php -> wp-content/plugins/wp-filebase/wp-filebase_css.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'wp-content/plugins/wp-filebase/wp-filebase_css.php' As you can see there is a gap of 14 seconds after the pass through of index.php. Any suggestions? I'm out of ideas again.

  Read the article

• Software for RAID Failure Alerts?

  - by QF_Developer

  I have two 256 GB Samsung 840 Pro SSD disks in a RAID 1 array. I would like to receive a notification if one of the disks in the array fails. Can anybody recommend an application I can install on the server to fire an email if such an event occurs? Here are some additional specs: Supermicro X9SCM-IIF motherboard utilising the hardware RAID controller. OS = Windows 2012 Standard Also is it possible to simulate a disk failure by pulling it out of the bay? SSDs appear to fail close together when in a mirrored config so I'd like to know ASAP if one goes down so I can swap them out with minimum delay. UPDATE 26th June 2013 ------------------------ None of the software that ships with the Supermicro X9SCM-* motherboards offer support for RAID monitoring. As has been pointed out here, these boards are built on an Intel chipset for RAID and so I installed Intel Rapid Storage Technology that supports automated email notifications on RAID failure http://www.intel.com/support/chipsets/imsm/sb/cs-020784.htm One small issue, the software only allows you to send email notifications without SMTP authentication. There's a bunch of different workarounds here: http://communities.intel.com/thread/30771

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• after building in more ram, bios/debian does nothing [closed]

  - by derty

  My private server has 2x1gb Ram working with a 64bit Debian and an Q6600 Intel. This runs 2 virtual mashines on it each one recives 512mb RAM. Which you can immagine is a bit tight for the hole system. Now i got 2x2gb ram from a friend. I'm not sure if thery are clocking at the same speed, but i'm sure my power adaptor is not on his limit and can handle that. So there are 2 ram sockets left at the mainboard. I shuted down the system and build in the 4 gigs and looked what happen. After pressing the start button, everything gets noisy as known BUT the screen shows nothing, not even the bios stuff it usally does. Why isn't the system booting? I can immagine that it does not direkt link between booting debian and the bios not showing a thing. Or is it Grub? I mounted the system disk, and i can see it, switch folders write stuff with "vim" it does not seems like there is a problem.

  Read the article

• Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

  - by AKa

  I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

  Read the article

• Security Token for Mac/Linux/Windows, self-managed, pref. open source?

  - by DevelopersDevelopersDevelopers

  I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

  Read the article

• can't install anything anymore with apt-get

  - by Aymane Shuichi

  Welcome this is the log I have when trying to install anything (php5-fpm after removing it) apt-get install php5-fpm Reading package lists... Done Building dependency tree Reading state information... Done php5-fpm is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up php5-fpm (5.4.4-14+deb7u10) ... insserv: warning: script 'S55IptabLes' missing LSB tags and overrides insserv: warning: script 'S55IptabLex' missing LSB tags and overrides insserv: There is a loop between service IptabLes and mountnfs if started insserv: loop involving service mountnfs at depth 8 insserv: loop involving service networking at depth 7 insserv: loop involving service mountnfs-bootclean at depth 10 insserv: There is a loop between service rc.local and mountall if started insserv: loop involving service mountall at depth 6 insserv: loop involving service checkfs at depth 5 insserv: loop involving service kbd at depth 11 insserv: There is a loop between service rc.local and mountall-bootclean if started insserv: loop involving service mountall-bootclean at depth 7 insserv: loop involving service urandom at depth 9 insserv: There is a loop between service IptabLes and mountdevsubfs if started insserv: loop involving service mountdevsubfs at depth 2 insserv: loop involving service udev at depth 1 insserv: There is a loop at service rc.local if started insserv: There is a loop at service IptabLes if started insserv: Starting IptabLes depends on rc.local and therefore on system facility `$all' which can not be true! (x99 times repeated ) insserv: Max recursions depth 99 reached insserv: loop involving service postfix at depth 2 insserv: There is a loop between service IptabLes and udev if started insserv: loop involving service mountkernfs at depth 1 insserv: loop involving service IptabLes at depth 1 Now here is the error i get insserv: exiting now without changing boot order! update-rc.d: error: insserv rejected the script header dpkg: error processing php5-fpm (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: php5-fpm E: Sub-process /usr/bin/dpkg returned an error code (1) The biggest operation I held before this was updating nginx from 1.2 to 1.6 and it was thanks to this site : here is the link : How to upgrade nginx from 1.2 to 1.6 on debian 7 Please help !

  Read the article

• Replicated filesystem and EC2 MySQL

  - by El Yobo

  I'm currently investigating migrating our infrastructure over to run on Amazon's EC2 and am trying to figure out the best way to set up a MySQL service. I'm leaning towards running our own MySQL instances, rather than going with Amazon's RDS, but am still considering the best approach for performance and cost on the instance itself. In order to have persistent data, the MySQL data needs to be on an EBS volume (with some form of striped RAID, e.g. RAID0 or RAID10) to improve persistence. However, EBS IO is limited by the network interface (gigabit, so a theoretical maximum of 128 MB/s), while the ephemeral volumes have no such problem. I did see a suggestion for running two MySQL servers on an instance, with a master running on the ephemeral disk (which we would also RAID) and a slave storing changes to an EBS volume, but this has some additional overhead and complexity (two servers). What I was imagining is using some form of replicated file system such that I could have a filesystem on top of a RAID0 of ephemeral volumes to maximise performance all changes from the above immediately replicated to another RAID1 volume backed by multiple EBS volumes to ensure no data loss The advantages of this would be best possible IO performance for the DB server; no network delay in IO decreased IO on EBS volumes (as all read IO will be done on the ephemeral volumes) so decreased cost good data security, as it's backed onto redundant EBS volumes However, I haven't seen an appropriate system to replicate all changes from one volume to the other; is there a filesystem, or any other approach, which will do this? The distributed file systems, e.g. GlusterFS, DRBD etc seem to focus on replicating disks between servers, can they be set up to do what I'm interested in here? I also haven't seen anything about other's taking this approach. Do I have a solution in need of a problem here (i.e. is performance good enough, so this whole idea is redundant)? Is there some flaw in the plan?

  Read the article

• Arduino IDE "launch 4j" error

  - by John

  I have a computer running Windows XP. I am trying to run the Arduino IDE 0022. I double-click on arduino.exe, it waits about 30 seconds on the load up title screen, and then it gives me this error: Launch 4j: an error occurred while starting the application My only choice is to click "OK"; the error goes away, and the Arduino IDE closes. If I try to delete the Arduino files (to try overwriting with some different files), I get an error that doesn't allow me to do so: Cannot delete awt.dll: Access denied Make sure the disk is not full or write protected and that the file is not currently in use. The only way to delete the file is by restarting the computer. So something must still be trying to run after that first error. I have noticed in Task Manager that some Java programs are still running: javaw.exe (3 processes) I think this is a problem with Java, but I checked and updated all of my Java software and it is all up to date. I have looked on other forums for this issue and none of them seemed to help. From the forums I have tried: Different Arduino IDE versions Updating Java Opening arduino.exe as Administrator Nothing has worked. Anyone have any suggestions?

  Read the article

• RAIDs with a lot of spindles - how to safely put to use the "wasted" space

  - by kubanczyk

  I have a fairly large number of RAID arrays (server controllers as well as midrange SAN storage) that all suffer from the same problem: barely enough spindles to keep the peak I/O performance, and tons of unused disk space. I guess it's a universal issue since vendors offer the smallest drives of 300 GB capacity but the random I/O performance hasn't really grown much since the time when the smallest drives were 36 GB. One example is a database that has 300 GB and needs random performance of 3200 IOPS, so it gets 16 disks (4800 GB minus 300 GB and we have 4.5 TB wasted space). Another common example are redo logs for a OLTP database that is sensitive in terms of response time. The redo logs get their own 300 GB mirror, but take 30 GB: 270 GB wasted. What I would like to see is a systematic approach for both Linux and Windows environment. How to set up the space so sysadmin team would be reminded about the risk of hindering the performance of the main db/app? Or, even better, to be protected from that risk? The typical situation that comes to my mind is "oh, I have this very large zip file, where do I uncompress it? Umm let's see the df -h and we figure something out in no time..." I don't put emphasis on strictness of the security (sysadmins are trusted to act in good faith), but on overall simplicity of the approach. For Linux, it would be great to have a filesystem customized to cap I/O rate to a very low level - is this possible?

  Read the article

< Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >