Search Results

Search found 2018 results on 81 pages for 'cr 48'.

Page 42/81 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• 2013 EC Elections Results

  - by Heather VanCura

  The 2013 Fall Executive Committee (EC) Elections process is now complete.  Congratulations to the following JCP Members as the new and re-elected EC Members!   We had a slight increase in JCP Member voter turnout at ~25% (up from 24% in 2012).  All Ratified candidates and the top eight Elected candidates were elected by the JCP Membership.  As part of the transition to a merged EC, Members elected in 2013 are ranked to determine whether their initial term will be one or two years. The 50% of Ratified and 50% of Elected members who receive the most votes will serve an initial two-year term, while all others will serve an initial one year term (details below). Ratified Seats: Credit Suisse, Ericsson, Freescale, Fujitsu, Gemalto M2M, Goldman Sachs, Hewlett-Packard, IBM, Intel, Nokia, Red Hat, SAP, SouJava, Software AG, TOTVS and V2COM. Open Election Seats: Eclipse Foundation, Twitter, London Java Community, CloudBees, ARM, Azul Systems, Werner Keil and MoroccoJUG. Newly elected EC Members take their seats on Tuesday, 12 November 2013.  More information is available on the JCP Elections page. Detailed Election Results Voting Period: 15 - 28 October 2013. Number of Eligible Voters: 1088 Percent of Eligible Members Casting Votes: 24.77% Ratified Seats: Candidate Yes Votes (%) No Votes (%) Abstentions Credit Suisse (2year term) 196 (84) 38 (16) 36 Ericsson (2 year term) 196 (88) 27 (12) 47 Freescale (1 year term) 151 (74) 53 (26) 66 Fujitsu (2 year term) 194 (87) 29 (13) 47 Gemalto M2M (1 year term) 170 (80) 42 (20) 58 Goldman Sachs (1 year term) 143 (64) 80 (36) 47 Hewlett-Packard (2 year term) 191 (82) 43 (18) 36 IBM (2 year term) 226 (91) 22 (9) 22 Intel (2 year term) 214 (90) 24 (10) 32 Nokia (1 year term) 139 (64) 78 (36) 53 Red Hat (2 year term) 245 (95) 12 (5) 13 SAP (1 year term) 166 (75) 56 (25) 48 SouJava (2 year term) 226 (92) 19 (8) 25 Software AG (1 year term) 167 (78) 47 (22) 56 TOTVS (1 year term) 129 (69) 59 (31) 82 V2COM (1 year term) 135 (71) 54 (29) 81 Open Election Seats: The top eight candidates have been elected; the top four receive a two year term, and the next four receive a one year term. Candidate Votes (%) Eclipse Foundation (2 year term) 221 (14) Twitter (2 year term) 203 (13) London Java Community (2 year term) 191 (12) CloudBees (2 year term) 179 (11) ARM (1 year term) 176 (11) Azul Systems (1 year term) 166 (10) Werner Keil (1 year term) 128 (8) MoroccoJUG (1 year term) 93 (6) Karan Malhi 56 (3) ChinaNanjingJUG 51 (3) JUG Joglosemar 47 (3) Viresh Wali 45 (3) ITP_JAVA 44 (3) None of the Above 3 (0)

  Read the article

• How to move a website and domain name without experiencing downtime for emails or site?

  - by user4842

  Okay, I have a pretty complex problem, so I'll get right to it. I'm a designer who built a new website for my client. Their old site is hosted at GoDaddy, as well as their email. Problem is, the guy who built the original site decided to put the original domain name and hosting under HIS personal GoDaddy account. Well, that turned out to be a bad move for several reasons. Here's how it's all tied together. The original domain name, www.domainoriginal.com, was actually purchased at Network Solutions. The original web designer pointed the nameservers from Network Solutions to his GoDaddy account, where the email and hosting is setup. The new domain name, www.domainnew.com, was purchased under a new and separate GoDaddy account belonging to the company, and the new website was built under a 3rd party platform (Big Commerce). So, the www.domainnew.com is already pointed to the new website using A records at new GoDaddy account. All is fine there. However, they still need www.domainoriginal.com to point to the NEW website as well. (The old one can simply be deleted, it is NOT important). AND, they want to keep their old email addresses intact and working as well, but under the NEW GoDaddy account. Obviously, I have no DNS control at Network Solutions, and I have no idea what kind of control I have at GoDaddy under the old account because the web designer will not let me see inside his account. But, he and GoDaddy both tell me nothing can be done other than to repoint the nameservers to Network Solutions, and then repoint the A record to my new website, www.domainnew.com, and point the MX Records to GoDaddy. I'm told the downtime would be 24-48 hours if I do this. Ideally, we'd like to do a domain name transfer and get www.domainoriginal.com in the new GoDaddy account created by the company. But, I'm told this could take up to 7 days. Does this mean the site and email will be down for 7 days? And any emails sent during this time, would they be lost forever? If I do this, how long could I expect the site and email to go down? And, will the emails be permanently lost? I've gotten different answers from everybody at GoDaddy so I kind of don't trust them anymore... Any help would be greatly appreciated Thanks, Tyson

  Read the article

• what's wrong with my sitemap?

  - by cadrian

  Google Webmaster Tools says that my sitemap is in a wrong format. I don't see my mistake, I think I followed every guideline provided by Google. Can someone help me? <?xml version="1.0" encoding="UTF-8"?> <urlset xmlns="http://www.sitemaps.org/schemas/sitemap/0.9"> <url> <loc>http://www.vocalcontraste.fr/</loc> </url> <url> <loc>http://www.vocalcontraste.fr/presentation/</loc> <lastmod>2012-01-30T21:49:06+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/les-concerts/</loc> <lastmod>2012-12-13T21:55:00+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/ecoutez-contraste/</loc> <lastmod>2012-07-13T18:19:45+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/repertoire/</loc> <lastmod>2012-07-13T17:30:14+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/la-presse/</loc> <lastmod>2012-07-11T08:17:48+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/recrutement/</loc> <lastmod>2012-02-01T22:22:03+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/nos-partenaires/</loc> <lastmod>2012-07-11T07:43:31+01:00</lastmod> </url> <url> <loc>http://www.vocalcontraste.fr/contactez-nous/</loc> <lastmod>2012-02-02T19:01:32+01:00</lastmod> </url> </urlset>

  Read the article

• Ask the Readers: Which Browser is a Must-Have for You on Linux?

  - by Asian Angel

  Linux systems all come with their own particular set of default browsers, but those browsers may not be the ones you want or need. This week we would like to know which browser (or browsers) are considered “must-have” on your Linux systems. As a general rule many Linux distributions have Firefox and/or Konqueror as one of the default installation browsers. During this past year the open source browser Chromium has also been gaining a lot of traction as a default install for systems. For most people these browsers are the ones that they like best or feel work well enough to not make any changes. But there are other people who want more than what is available with a default system install. They may favor a particular browser for its’ extensibility or speed…others prefer a particular browser for its’ features or minimalist UI. Whatever your preferences may be, there is a browser out there to fit your style. Some people may even prefer to run only bleeding edge nightly releases or add them in with their current browsers. The important part is that you have choices when it comes to your Linux system. What we would like to know this week is which browser or browsers you make sure are always installed on your Linux systems. Does the Linux system you use already have your favorite browser installed as part of the default set? Maybe you are content with using the default set of browsers that come with the system. Or perhaps you prefer to rework the entire browser setup on your system by removing the defaults and adding your favorites. Let us know which browsers you consider “must have” and why in the comments! Note: You can make up to two selections on today’s poll since most people will likely have more than one browser that they make certain is always installed. How-To Geek Polls require Javascript. Please Click Here to View the Poll. Latest Features How-To Geek ETC How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 The 50 Best How-To Geek Windows Articles of 2010 The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC BotSync Enables Secure FTP File Synchronization on Android Devices Enjoy Beautiful City Views with the Cityscape Theme for Windows 7 Luigi Installs Any OS on Google’s Cr-48 Notebook DIY iPad Stylus Offers Pen-Based Interaction on the Cheap Serene Blue Ubuntu Wallpaper for Your Desktop Enjoy Old School Style Video Game Fun with Chicken Invaders

  Read the article

• Wireless connection by using command screen

  - by Amadeus

  I installed Ubuntu 12.04 armhf to my beagleboard-xm and now trying to connect to a wireless network. First, I checked if I can search for available networks: ubuntu@arm:~$ iwlist scan lo Interface doesn't support scanning. usb0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: EA:7D:EF:60:C9:0B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=70/70 Signal level=-23 dBm Encryption key:on ESSID:"ghostrider" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Ad-Hoc Extra:tsf=000000005a1ab50e Extra: Last beacon: 6242ms ago IE: Unknown: 000A67686F73747269646572 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 06020000 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: 2D1A2C181BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D16010800000000FF000000000000000000000000000000 IE: Unknown: DD09001018020000000000 Then I edited /etc/network/interfaces file to the following: root@arm:/etc/wpa_supplicant# cat /etc/network/interfaces auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # Example to keep MAC address between reboots #hwaddress ether DE:AD:BE:EF:CA:FE # WiFi Example auto wlan0 iface wlan0 inet dhcp wpa-ssid "ghostrider" wpa-psk "b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf" But I cannot still connect to the wireless network: root@arm:/etc/wpa_supplicant# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Asociated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on eth0 no wireless extensions. root@arm:/etc/network# ifup wlan0 Failed to bring up wlan0. What is wrong? Should I change any other files also? But I think it was enough. By the way if you are curious about where that wpa-psk came from: zero@ghostrider:~$ wpa_passphrase ghostrider 34bddf67c2 network={ ssid="ghostrider" #psk="34bddf67c2" psk=b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf } I will appreciate any effort to help. Regards, Amadeus ps: Also I tried to connect manually: root@arm:/etc/network# iwconfig wlan0 essid ghostrider key s:34bddf67c2 But this did not solve my problem also.

  Read the article

• Glm Vector Transformations [duplicate]

  - by Reanimation

  This question already has an answer here: Car-like Physics - Basic Maths to Simulate Steering 2 answers I have a cube rendered on the screen which represents a car (or similar). Using Projection/Model matrices and Glm I am able to move it back and fourth along the axes and rotate it left or right. I'm having trouble with the vector mathematics to make the cube move forwards no matter which direction it's current orientation is. (ie. if I would like, if it's rotated right 30degrees, when it's move forwards, it travels along the 30degree angle on a new axes). I hope I've explained that correctly. This is what I've managed to do so far in terms of using glm to move the cube: glm::vec3 vel; //velocity vector void renderMovingCube(){ glUseProgram(movingCubeShader.handle()); GLuint matrixLoc4MovingCube = glGetUniformLocation(movingCubeShader.handle(), "ProjectionMatrix"); glUniformMatrix4fv(matrixLoc4MovingCube, 1, GL_FALSE, &ProjectionMatrix[0][0]); glm::mat4 viewMatrixMovingCube; viewMatrixMovingCube = glm::lookAt(camOrigin, camLookingAt, camNormalXYZ); vel.x = cos(rotX); vel.y=sin(rotX); vel*=moveCube; //move cube ModelViewMatrix = glm::translate(viewMatrixMovingCube,globalPos*vel); //bring ground and cube to bottom of screen ModelViewMatrix = glm::translate(ModelViewMatrix, glm::vec3(0,-48,0)); ModelViewMatrix = glm::rotate(ModelViewMatrix, rotX, glm::vec3(0,1,0)); //manually turn glUniformMatrix4fv(glGetUniformLocation(movingCubeShader.handle(), "ModelViewMatrix"), 1, GL_FALSE, &ModelViewMatrix[0][0]); //pass matrix to shader movingCube.render(); //draw glUseProgram(0); } keyboard input: void keyboard() { char BACKWARD = keys['S']; char FORWARD = keys['W']; char ROT_LEFT = keys['A']; char ROT_RIGHT = keys['D']; if (FORWARD) //W - move forwards { globalPos += vel; //globalPos.z -= moveCube; BACKWARD = false; } if (BACKWARD)//S - move backwards { globalPos.z += moveCube; FORWARD = false; } if (ROT_LEFT)//A - turn left { rotX +=0.01f; ROT_LEFT = false; } if (ROT_RIGHT)//D - turn right { rotX -=0.01f; ROT_RIGHT = false; } Where am I going wrong with my vectors? I would like change the direction of the cube (which it does) but then move forwards in that direction.

  Read the article

• Fans running very fast on MacBook Pro 8.1 ubuntu 12.04

  - by Tomasz Kacprzak

  I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

  Read the article

• Fans running very fast on MacBook Pro 8.1

  - by Tomasz Kacprzak

  I installed Ubuntu 12.04 on Macbook Pro 8.1 and one of the first things I noticed was that the fans were starting to spin very fast every few minutes for 10-30 sec and then going back to normal. That was happening even without any processor load, when completely idle. The fans were usually spinning at 4000 RPM and made much noise. The computer was not getting hotter than usual. When running OSX Lion there was no noise at all, fans almost all the time at 2000 RPM. I spent some time on it and found out that Precise uses a deamon to control the temperature, called macfanctld. You can use /etc/macfanctld.conf to set the configuration. I found out that the high fan speed is not due to the fact that the temperature is getting hot, but because there are two sensors which indicate wrong numbers (you can check that using 'sensors' command ): TW0P: +129.0°C TCTD: +256.0°C TCFC: +0.0°C TMBS: +0.0°C or setting the macfanctld log level to 2: Speed: 4992, *AVG: 56.9C, TC0P: 50.2C, TG0P: 51.5C, Sensors: TB0T:34 TB1T:34 TB2T:33 TC0C:58 TC0D:56 TC0E:59 TC0F:60 TC0P:50 TC1C:58 TC2C:58 TC3C:58 TC4C:57 TCFC:0 TCGC:57 TCSA:53 TCTD:256 TG0D:52 TG0P:52 THSP:42 TM0S:64 TMBS:0 TP0P:54 TPCD:60 TW0P:129 Th1H:51 Th2H:48 Tm0P:40 Ts0P:32 Ts0S:43 Moreover, TCTD was randomly jumping from temperatures of 0 to 256, so this may be the reason for unjustified random fan speeds. macfanctld is taking an average of the sensors including the values above, so the actual AVG temp used to control the fans is wrong, usually biased up, hence high RPM and noise. The workaround solution is to use an option in the macfanctld.conf which allows to ignore the malfunctioning sensors: exclude: 13 16 21 24 After reboot the reported temperatures are usually normal and the fans are working at reasonable speeds. I tested the response of the fans to heavy processor load by asking MATLAB to invert 10000x10000 matrix and the AVG temperature jumped to 63deg, and the fan to max 6200 RPM and then got it back to normal temperature. So I think it is safe so far. There is a expired bug about the failing sensor readings: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/955538 which may be good to open again. My question would be: does anyone know what the failing sensors do and if there is any danger in excluding them? Maybe some better solution to this problem?

  Read the article

• Silverlight and WCF caching

  - by subodhnpushpak

  There are scenarios where Silverlight client calls WCF (or REST) service for data. Now, if the data is cached on the WCF layer, the calls can take considerable resources at the server if NOT cached. Keeping that in mind along with the fact that cache is an cross-cutting aspect, and therefore it should be as easy as possible to put Cache wherever required. The good thing about the solution is that it caches based on the inputs. The input can be basic type of any complex type. If input changes the data is fetched and then cached for further used. If same input is provided again, data id fetched from the cache. The cache logic itself is implemented as PostSharp aspect, and it is as easy as putting an attribute over service call to switch on cache. Notice how clean the code is:        [OperationContract]       [CacheOnArgs(typeof(int))] // based on actual value of cache        public string DoWork(int value)        {            return string.Format("You entered: {0} @ cached time {1}", value, System.DateTime.Now);        } The cache is implemented as POST Sharp as below 1: public override void OnInvocation(MethodInvocationEventArgs eventArgs) 2: { 3: try 4: { 5: object value = new object(); 6: object[] args = eventArgs.GetArgumentArray(); 7: if (args != null || args.Count() > 0) 8: { 9:   10: string key = string.Format("{0}_{1}", eventArgs.Method.Name, XMLUtility<object>.GetDataContractXml(args[0], null));// Compute the cache key (details omitted). 11:   12: 13: value = GetFromCache(key); 14: if (value == null) 15: { 16: eventArgs.Proceed(); 17: value = XMLUtility<object>.GetDataContractXml(eventArgs.ReturnValue, null); 18: value = eventArgs.ReturnValue; 19: AddToCache(key, value); 20: return; 21: } 22:   23:   24: Log(string.Format("Data returned from Cache {0}",value)); 25: eventArgs.ReturnValue = value; 26: } 27: } 28: catch (Exception ex) 29: { 30: //ApplicationLogger.LogException(ex.Message, Source.UtilityService); 31: } 32: } 33:   34: private object GetFromCache(string inputKey) { if (ServerConfig.CachingEnabled) { return WCFCache.Current[inputKey]; } return null; }private void AddToCache(string inputKey,object outputValue) 35: { 36: if (ServerConfig.CachingEnabled) 37: { 38: if (WCFCache.Current.CachedItemsNumber < ServerConfig.NumberOfCachedItems) 39: { 40: if (ServerConfig.SlidingExpirationTime <= 0 || ServerConfig.SlidingExpirationTime == int.MaxValue) 41: { 42: WCFCache.Current[inputKey] = outputValue; 43: } 44: else 45: { 46: WCFCache.Current.Insert(inputKey, outputValue, new TimeSpan(0, 0, ServerConfig.SlidingExpirationTime), true); 47:   48: // _bw.DoWork += bw_DoWork; 49: //string arg = string.Format("{0}|{1}", inputKey,outputValue); 50: //_bw.RunWorkerAsync(inputKey ); 51: } 52: } 53: } 54: }     The cache class can be extended to support Velocity / memcahe / Nache. the attribute can be used over REST services as well. Hope the above helps. Here is the code base for the same.   Please do provide your inputs / comments.

  Read the article

• Oracle Data Protection: How Do You Measure Up? - Part 1

  - by tichien

  This is the first installment in a blog series, which examines the results of a recent database protection survey conducted by Database Trends and Applications (DBTA) Magazine. All Oracle IT professionals know that a sound, well-tested backup and recovery strategy plays a foundational role in protecting their Oracle database investments, which in many cases, represent the lifeblood of business operations. But just how common are the data protection strategies used and the challenges faced across various enterprises? In January 2014, Database Trends and Applications Magazine (DBTA), in partnership with Oracle, released the results of its “Oracle Database Management and Data Protection Survey”. Two hundred Oracle IT professionals were interviewed on various aspects of their database backup and recovery strategies, in order to identify the top organizational and operational challenges for protecting Oracle assets. Here are some of the key findings from the survey: The majority of respondents manage backups for tens to hundreds of databases, representing total data volume of 5 to 50TB (14% manage 50 to 200 TB and some up to 5 PB or more). About half of the respondents (48%) use HA technologies such as RAC, Data Guard, or storage mirroring, however these technologies are deployed on only 25% of their databases (or less). This indicates that backups are still the predominant method for database protection among enterprises. Weekly full and daily incremental backups to disk were the most popular strategy, used by 27% of respondents, followed by daily full backups, which are used by 17%. Interestingly, over half of the respondents reported that 10% or less of their databases undergo regular backup testing.  A few key backup and recovery challenges resonated across many of the respondents: Poor performance and impact on productivity (see Figure 1) 38% of respondents indicated that backups are too slow, resulting in prolonged backup windows. In a similar vein, 23% complained that backups degrade the performance of production systems. Lack of continuous protection (see Figure 2) 35% revealed that less than 5% of Oracle data is protected in real-time.  Management complexity 25% stated that recovery operations are too complex. (see Figure 1)  31% reported that backups need constant management. (see Figure 1) 45% changed their backup tools as a result of growing data volumes, while 29% changed tools due to the complexity of the tools themselves. Figure 1: Current Challenges with Database Backup and Recovery Figure 2: Percentage of Organization’s Data Backed Up in Real-Time or Near Real-Time In future blogs, we will discuss each of these challenges in more detail and bring insight into how the backup technology industry has attempted to resolve them.

  Read the article

• Postfix not delivering email using Maildir

  - by Greg K

  I've followed this guide to get postfix set up. I've not completed it yet, as from sending test emails, email is no longer being delivered since switching to Maildir from mbox. I have created a Maildir directory with cur, new and tmp sub directories. ~$ ll drwxrwxr-x 5 greg greg 4096 2012-07-07 16:40 Maildir/ ~$ ll Maildir/ drwxrwxr-x 2 greg greg 4096 2012-07-07 16:40 cur drwxrwxr-x 2 greg greg 4096 2012-07-07 16:40 new drwxrwxr-x 2 greg greg 4096 2012-07-07 16:40 tmp Send a test email. ~$ netcat mail.example.com 25 220 ubuntu ESMTP Postfix (Ubuntu) ehlo example.com 250-ubuntu 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN mail from: [email protected] 250 2.1.0 Ok rcpt to: [email protected] 250 2.1.5 Ok data 354 End data with <CR><LF>.<CR><LF> Subject: test email Hi, Just testing. . 250 2.0.0 Ok: queued as 56B541EA53 quit 221 2.0.0 Bye Check the mail queue. ~$ mailq Mail queue is empty Check if mail has been delivered. ~$ ls -l Maildir/new total 0 Some postfix settings: ~$ sudo postconf home_mailbox home_mailbox = Maildir/ ~$ sudo postconf mailbox_command mailbox_command = /var/log/mail.log Jul 7 16:57:33 li305-246 postfix/smtpd[21039]: connect from example.com[178.79.168.xxx] Jul 7 16:58:14 li305-246 postfix/smtpd[21039]: 56B541EA53: client=example.com[178.79.168.xxx] Jul 7 16:58:33 li305-246 postfix/cleanup[21042]: 56B541EA53: message-id=<20120707155814.56B541EA53@ubuntu> Jul 7 16:58:33 li305-246 postfix/qmgr[20882]: 56B541EA53: from=<[email protected]>, size=321, nrcpt=1 (queue active) Jul 7 16:58:33 li305-246 postfix/smtp[21043]: 56B541EA53: to=<[email protected]>, relay=none, delay=30, delays=30/0.01/0/0, dsn=5.4.6, status=bounced (mail for example.com loops back to myself) Jul 7 16:58:33 li305-246 postfix/cleanup[21042]: 1F68B1EA55: message-id=<20120707155833.1F68B1EA55@ubuntu> Jul 7 16:58:33 li305-246 postfix/bounce[21044]: 56B541EA53: sender non-delivery notification: 1F68B1EA55 Jul 7 16:58:33 li305-246 postfix/qmgr[20882]: 1F68B1EA55: from=<>, size=1999, nrcpt=1 (queue active) Jul 7 16:58:33 li305-246 postfix/qmgr[20882]: 56B541EA53: removed Jul 7 16:58:33 li305-246 postfix/smtp[21043]: 1F68B1EA55: to=<[email protected]>, relay=none, delay=0, delays=0/0/0/0, dsn=5.4.6, status=bounced (mail for example.com loops back to myself) Jul 7 16:58:33 li305-246 postfix/qmgr[20882]: 1F68B1EA55: removed Jul 7 16:58:36 li305-246 postfix/smtpd[21039]: disconnect from domain.me[178.79.168.xxx] Jul 7 17:10:38 li305-246 postfix/master[20878]: terminating on signal 15 Jul 7 17:10:39 li305-246 postfix/master[21254]: daemon started -- version 2.8.5, configuration /etc/postfix Any ideas?

  Read the article

• MS Excel not installed after uninstalling Crystal Reports Viewer

  - by PowerUser

  I recently tried out the free Crystal Reports Viewer. I installed it on my work computer, but it didn't load (crashed on the EULA agreement of all places). After uninstalling the viewer, however, MS Excel 2003 does 3 things: "An error occurred initializing the VBA libraries (1004)" "Microsoft Excel has not been installed for the current user" Excel then closes. Did uninstalling the CR Viewer take some Microsoft DLLs with it? How do I get Excel working again?

  Read the article

• Unable to define a mapping including the '.' key

  - by Ton van den Heuvel

  I am trying to define a mapping for Ctrl+. as follows: map <C-.> :bn<CR> This does not work. Typing Ctrl+. just results in repeating the last action just as you would get when typing .. Note that I do not want to change the behaviour of .. Any idea how to get this to work?

  Read the article

• lwjgl isKeyDown canceling out other keys

  - by AKrush95

  While trying to create a simple game where a square is manipulated via the keyboard keys, I have come across a small, rather irritating problem. I would like it to work so that when the opposite directional key is pressed, the character will stop; the character may move the other two directions while stopped in this situation. This works perfectly with LEFT and RIGHT held down; the player may move UP or DOWN. If UP and DOWN are held down, however, the player will not move, nor will Java recognize that the LEFT or RIGHT keys were pressed. import java.util.ArrayList; import java.util.Random; import org.lwjgl.*; import org.lwjgl.input.Keyboard; import org.lwjgl.opengl.*; import static org.lwjgl.opengl.GL11.*; public class Main { private Man p; private ArrayList<Integer> keysDown, keysUp; public Main() { try { Display.setDisplayMode(new DisplayMode(640, 480)); Display.setTitle("LWJGLHelloWorld"); Display.create(); } catch (LWJGLException e) { e.printStackTrace(); } p = new Man(0, 0); keysDown = new ArrayList<>(); keysUp = new ArrayList<>(); glMatrixMode(GL_PROJECTION); glLoadIdentity(); glOrtho(0, 640, 480, 0, 1, -1); glMatrixMode(GL_MODELVIEW); while (!Display.isCloseRequested()) { glClear(GL_COLOR_BUFFER_BIT); checkKeys(); p.draw(); Display.update(); Display.sync(60); } Display.destroy(); } public void checkKeys() { ArrayList<Integer> keys = new ArrayList<>(); keys.add(Keyboard.KEY_A); keys.add(Keyboard.KEY_D); keys.add(Keyboard.KEY_W); keys.add(Keyboard.KEY_S); for (int key : keys) { if (Keyboard.isKeyDown(key)) keysDown.add(key); else keysUp.add(key); } keysDown.removeAll(keysUp); keysUp = new ArrayList<>(); int speed = 4; int dx = 0; int dy = 0; if (keysDown.contains(keys.get(2))) { System.out.println("keyUP"); dy -= speed; } if (keysDown.contains(keys.get(3))) { System.out.println("keyDOWN"); dy += speed; } if (keysDown.contains(keys.get(0))) { System.out.println("keyLEFT"); dx -= speed; } if (keysDown.contains(keys.get(1))) { System.out.println("keyRIGHT"); dx += speed; } //if (keysDown.contains(keys.get(0)) && keysDown.contains(keys.get(1))) dx = 0; //if (keysDown.contains(keys.get(2)) && keysDown.contains(keys.get(3))) dy = 0; p.update(dx, dy); } public static void main(String[] args) { new Main(); } class Man { public int x, y, w, h; public float cR, cG, cB; public Man(int x, int y) { this.x = x; this.y = y; w = 50; h = 50; Random rand = new Random(); cR = rand.nextFloat(); cG = rand.nextFloat(); cB = rand.nextFloat(); } public void draw() { glColor3f(cR, cG, cB); glRecti(x, y, x+w, y+h); } public void update(int dx, int dy) { x += dx; y += dy; } } } That is the code that I am working with. In addition, I am unsure how to compile an executable jar that is using the lwjgl library in addition to slick-util.

  Read the article

• Windows Server 2008 R2 Error CAPI2 Event ID 4107

  - by umar bhatti

  I am getting following error on couple of my 2008 R2 servers. I have tried couple of fixes which didn't fix the issues. Log Name: Application Source: Microsoft-Windows-CAPI2 Date: 18/03/2013 09:48:40 Event ID: 4107 Task Category: None Level: Error Keywords: Classic User: N/A Computer: ServerName Description: Failed extract of third-party root list from auto update cab at: <http://ctldl.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab> with error: The data is invalid. . Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-CAPI2" Guid="{5bbca4a8-b209-48dc-a8c7-b23d3e5216fb}" EventSourceName="Microsoft-Windows-CAPI2" /> <EventID Qualifiers="0">4107</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2013-03-18T09:48:40.169581600Z" /> <EventRecordID>8713</EventRecordID> <Correlation /> <Execution ProcessID="412" ThreadID="5288" /> <Channel>Application</Channel> <Computer>ServerName <Security /> </System> <EventData> <Data>http://ctldl.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab</Data> <Data>The data is invalid. </Data> </EventData> </Event>

  Read the article

• php-fpm: very high server load

  - by Derp Derpington

  Since today my webserver (nginx + php-fpm + mysql on a VPS) is very slow. htop says: 1 [|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||100.0%] Tasks: 63 total, 13 running 2 [|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||100.0%] Load average: 11.67 10.95 6.95 3 [|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||100.0%] Uptime: 00:18:40 4 [|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||100.0%] 5 [|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||100.0%] 6 [|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||100.0%] Mem[||||||||||| 137/1280MB] Swp[ 0/0MB] PID USER PRI NI VIRT RES SHR S CPU% MEM% TIME+ Command 6802 www 20 0 76232 12320 5716 R 27.0 0.9 0:06.48 php-fpm: pool www 7048 www 20 0 75200 12136 5700 R 52.0 0.9 0:03.64 php-fpm: pool www 6699 www 20 0 74176 11124 5700 R 27.0 0.8 0:07.36 php-fpm: pool www 7029 www 20 0 73668 10380 5676 R 42.0 0.8 0:03.52 php-fpm: pool www 6995 www 20 0 76228 12456 5644 R 42.0 1.0 0:03.98 php-fpm: pool www 6858 www 20 0 74172 10684 5620 R 35.0 0.8 0:05.52 php-fpm: pool www 6998 www 20 0 75200 12072 5620 R 37.0 0.9 0:03.95 php-fpm: pool www 7098 www 20 0 75200 12052 5616 R 42.0 0.9 0:02.33 php-fpm: pool www 7093 www 20 0 76228 12496 5612 R 37.0 1.0 0:03.02 php-fpm: pool www 7226 www 20 0 74692 11080 5588 R 32.0 0.8 0:00.66 php-fpm: pool www CPU: (cat /proc/cpuinfo | grep model) model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz model : 44 model name : Intel(R) Xeon(R) CPU E5620 @ 2.40GHz I think a load of 10 and 100% cpu usage is not normal... How can i fix that?

  Read the article

• Server 2008 RAID5 resynching

  - by benpage

  I built a W2K8 R2 server last weekend, and built a R5 array using Disk Management, 5x 1TB drives. For the next 60 hours the status said 'Resynching (X%)' as it built the array. during this time i did read and write to the drive (slowly) and once the rebuild was complete speeds were quite fast. I was copying over some data from a USB hard drive overnight, and the machine crashed (looking in the error i believe it was the driver for the usb drive) and so the RAID5 went back to resynching, since the machine was not shut down properly. The issue is, it's been about 48 hours since that started and I'm happy to say it will take roughly 60 hours again to resynch, however.. all this time in Disk Management, the status has only said 'Resynching', not 'Resynching (X%)'. The hard drive light is going nuts, and read/writes are slow again, so I'm assuming it is actually resynching. The question is - is that a correct assumption? and why is disk management not telling me what %age it's done? Is this normal behaviour for a not-properly-shut-down r5 array?

  Read the article

• NFS issue: clients can mount shares as NFSv3 but not as NFSv4 -- or how to debug NFS?

  - by tdn

  Problem description I have a file server running Debian. On it I have a few NFS shares. When I mount the shares from a client using NFSv3 (mount.nfs 10.0.0.51:/exports/video /mnt -o vers=3,soft,intr,timeo=10), it works. However, I would like to use NFSv4 because of improved security and performance. When I try to mount an NFSv4 share on malbec the mount command just hangs and finally times out after 2 minutes. How do I make the clients mount the NFSv4 shares as NFSv4? How do I troubleshoot NFS? There is no information in the syslog on neither client nor server. What are any errors in my configuration? Facts: Server is corvina(10.0.0.51) Client is malbec(10.0.0.1) Malbec runs Ubuntu 12.04 Server runs Debian 7 wheezy Both are connected through 1 GbE LAN. Firewalls are off. rpcinfo (root@malbec) (13-07-02 21:00) (P:0 L:1) [0] ~ # rpcinfo -p program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100024 1 udp 4000 status 100024 1 tcp 4000 status (root@malbec) (13-07-02 21:00) (P:0 L:1) [0] ~ # rpcinfo -p corvina program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100024 1 udp 4000 status 100024 1 tcp 4000 status 100003 3 udp 2049 nfs 100227 3 udp 2049 100021 1 udp 4003 nlockmgr 100021 3 udp 4003 nlockmgr 100021 4 udp 4003 nlockmgr 100021 1 tcp 4003 nlockmgr 100021 3 tcp 4003 nlockmgr 100021 4 tcp 4003 nlockmgr 100005 1 udp 4002 mountd 100005 1 tcp 4002 mountd 100005 2 udp 4002 mountd 100005 2 tcp 4002 mountd 100005 3 udp 4002 mountd 100005 3 tcp 4002 mountd tcpdump The following is output from tcpdump on malbec while running this command: # rpcinfo -p corvina ~ # tcpdump -i eth0 host 10.0.0.51 21:14:51.762083 IP malbec.vineyard.sikkerhed.org.948 > corvina.vineyard.sikkerhed.org.sunrpc: Flags [S], seq 3069120722, win 14600, options [mss 1460,sackOK,TS val 146111 ecr 0,nop,wscale 7], length 0 21:14:51.762431 IP corvina.vineyard.sikkerhed.org.sunrpc > malbec.vineyard.sikkerhed.org.948: Flags [S.], seq 770684199, ack 3069120723, win 14480, options [mss 1460,sackOK,TS val 398850 ecr 146111,nop,wscale 7], length 0 21:14:51.762458 IP malbec.vineyard.sikkerhed.org.948 > corvina.vineyard.sikkerhed.org.sunrpc: Flags [.], ack 1, win 115, options [nop,nop,TS val 146111 ecr 398850], length 0 21:14:51.762556 IP malbec.vineyard.sikkerhed.org.948 > corvina.vineyard.sikkerhed.org.sunrpc: Flags [P.], seq 1:45, ack 1, win 115, options [nop,nop,TS val 146111 ecr 398850], length 44 21:14:51.762710 IP corvina.vineyard.sikkerhed.org.sunrpc > malbec.vineyard.sikkerhed.org.948: Flags [.], ack 45, win 114, options [nop,nop,TS val 398850 ecr 146111], length 0 21:14:51.763282 IP corvina.vineyard.sikkerhed.org.sunrpc > malbec.vineyard.sikkerhed.org.948: Flags [P.], seq 1:473, ack 45, win 114, options [nop,nop,TS val 398850 ecr 146111], length 472 21:14:51.763302 IP malbec.vineyard.sikkerhed.org.948 > corvina.vineyard.sikkerhed.org.sunrpc: Flags [.], ack 473, win 123, options [nop,nop,TS val 146111 ecr 398850], length 0 21:14:51.764059 IP malbec.vineyard.sikkerhed.org.948 > corvina.vineyard.sikkerhed.org.sunrpc: Flags [F.], seq 45, ack 473, win 123, options [nop,nop,TS val 146111 ecr 398850], length 0 21:14:51.764454 IP corvina.vineyard.sikkerhed.org.sunrpc > malbec.vineyard.sikkerhed.org.948: Flags [F.], seq 473, ack 46, win 114, options [nop,nop,TS val 398850 ecr 146111], length 0 21:14:51.764478 IP malbec.vineyard.sikkerhed.org.948 > corvina.vineyard.sikkerhed.org.sunrpc: Flags [.], ack 474, win 123, options [nop,nop,TS val 146111 ecr 398850], length 0 The following is output from tcpdump on malbec while runing this command: ~ # time mount.nfs4 10.0.0.51:/ /mnt -o soft,intr,timeo=10 21:14:58.397327 IP malbec.vineyard.sikkerhed.org.872 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1298959870, win 14600, options [mss 1460,sackOK,TS val 147769 ecr 0,nop,wscale 7], length 0 21:14:58.397655 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.872: Flags [R.], seq 0, ack 1298959871, win 0, length 0 21:14:59.470270 IP malbec.vineyard.sikkerhed.org.854 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 4111013041, win 14600, options [mss 1460,sackOK,TS val 148038 ecr 0,nop,wscale 7], length 0 21:14:59.470569 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.854: Flags [R.], seq 0, ack 4111013042, win 0, length 0 21:15:01.506179 IP malbec.vineyard.sikkerhed.org.988 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1642454567, win 14600, options [mss 1460,sackOK,TS val 148547 ecr 0,nop,wscale 7], length 0 21:15:01.506514 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.988: Flags [R.], seq 0, ack 1642454568, win 0, length 0 21:15:05.542216 IP malbec.vineyard.sikkerhed.org.882 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 3844460520, win 14600, options [mss 1460,sackOK,TS val 149556 ecr 0,nop,wscale 7], length 0 21:15:05.542484 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.882: Flags [R.], seq 0, ack 3844460521, win 0, length 0 21:15:13.602228 IP malbec.vineyard.sikkerhed.org.969 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1317773588, win 14600, options [mss 1460,sackOK,TS val 151571 ecr 0,nop,wscale 7], length 0 21:15:13.602527 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.969: Flags [R.], seq 0, ack 1317773589, win 0, length 0 21:15:18.615027 ARP, Request who-has malbec.vineyard.sikkerhed.org tell corvina.vineyard.sikkerhed.org, length 46 21:15:18.615048 ARP, Reply malbec.vineyard.sikkerhed.org is-at cc:52:af:46:af:23 (oui Unknown), length 28 21:15:23.622223 IP malbec.vineyard.sikkerhed.org.1003 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 2896563167, win 14600, options [mss 1460,sackOK,TS val 154076 ecr 0,nop,wscale 7], length 0 21:15:23.622557 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.1003: Flags [R.], seq 0, ack 2896563168, win 0, length 0 21:15:28.629913 ARP, Request who-has corvina.vineyard.sikkerhed.org tell malbec.vineyard.sikkerhed.org, length 28 21:15:28.630223 ARP, Reply corvina.vineyard.sikkerhed.org is-at 00:9c:02:ab:db:54 (oui Unknown), length 46 21:15:33.662200 IP malbec.vineyard.sikkerhed.org.727 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1334644196, win 14600, options [mss 1460,sackOK,TS val 156586 ecr 0,nop,wscale 7], length 0 21:15:33.663657 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.727: Flags [R.], seq 0, ack 1334644197, win 0, length 0 21:15:43.698207 IP malbec.vineyard.sikkerhed.org.rsync > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 688828331, win 14600, options [mss 1460,sackOK,TS val 159095 ecr 0,nop,wscale 7], length 0 21:15:43.698541 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.rsync: Flags [R.], seq 0, ack 688828332, win 0, length 0 21:15:48.707710 ARP, Request who-has malbec.vineyard.sikkerhed.org tell corvina.vineyard.sikkerhed.org, length 46 21:15:48.707726 ARP, Reply malbec.vineyard.sikkerhed.org is-at cc:52:af:46:af:23 (oui Unknown), length 28 21:15:53.738188 IP malbec.vineyard.sikkerhed.org.946 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 2021272456, win 14600, options [mss 1460,sackOK,TS val 161605 ecr 0,nop,wscale 7], length 0 21:15:53.738519 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.946: Flags [R.], seq 0, ack 2021272457, win 0, length 0 21:16:03.806216 IP malbec.vineyard.sikkerhed.org.902 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 3889059201, win 14600, options [mss 1460,sackOK,TS val 164122 ecr 0,nop,wscale 7], length 0 21:16:03.806546 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.902: Flags [R.], seq 0, ack 3889059202, win 0, length 0 21:16:08.821900 ARP, Request who-has corvina.vineyard.sikkerhed.org tell malbec.vineyard.sikkerhed.org, length 28 21:16:08.822172 ARP, Reply corvina.vineyard.sikkerhed.org is-at 00:9c:02:ab:db:54 (oui Unknown), length 46 21:16:13.874209 IP malbec.vineyard.sikkerhed.org.712 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1480927452, win 14600, options [mss 1460,sackOK,TS val 166639 ecr 0,nop,wscale 7], length 0 21:16:13.874553 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.712: Flags [R.], seq 0, ack 1961062188, win 0, length 0 21:16:18.880588 ARP, Request who-has malbec.vineyard.sikkerhed.org tell corvina.vineyard.sikkerhed.org, length 46 21:16:18.880605 ARP, Reply malbec.vineyard.sikkerhed.org is-at cc:52:af:46:af:23 (oui Unknown), length 28 21:16:23.910209 IP malbec.vineyard.sikkerhed.org.758 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1375860626, win 14600, options [mss 1460,sackOK,TS val 169148 ecr 0,nop,wscale 7], length 0 21:16:23.910532 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.758: Flags [R.], seq 0, ack 1375860627, win 0, length 0 21:16:33.982258 IP malbec.vineyard.sikkerhed.org.694 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 1769203987, win 14600, options [mss 1460,sackOK,TS val 171666 ecr 0,nop,wscale 7], length 0 21:16:33.982579 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.694: Flags [R.], seq 0, ack 1769203988, win 0, length 0 21:16:44.026241 IP malbec.vineyard.sikkerhed.org.841 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 530553783, win 14600, options [mss 1460,sackOK,TS val 174177 ecr 0,nop,wscale 7], length 0 21:16:44.026505 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.841: Flags [R.], seq 0, ack 530553784, win 0, length 0 21:16:46.213388 IP malbec.vineyard.sikkerhed.org.43460 > corvina.vineyard.sikkerhed.org.ssh: Flags [P.], seq 64:128, ack 33, win 325, options [nop,nop,TS val 174723 ecr 397437], length 64 21:16:46.213859 IP corvina.vineyard.sikkerhed.org.ssh > malbec.vineyard.sikkerhed.org.43460: Flags [P.], seq 33:65, ack 128, win 199, options [nop,nop,TS val 427466 ecr 174723], length 32 21:16:46.213883 IP malbec.vineyard.sikkerhed.org.43460 > corvina.vineyard.sikkerhed.org.ssh: Flags [.], ack 65, win 325, options [nop,nop,TS val 174723 ecr 427466], length 0 21:16:54.094242 IP malbec.vineyard.sikkerhed.org.kerberos-master > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 2673083337, win 14600, options [mss 1460,sackOK,TS val 176694 ecr 0,nop,wscale 7], length 0 21:16:54.094568 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.kerberos-master: Flags [R.], seq 0, ack 2673083338, win 0, length 0 21:17:04.134227 IP malbec.vineyard.sikkerhed.org.1019 > corvina.vineyard.sikkerhed.org.nfs: Flags [S], seq 2176607713, win 14600, options [mss 1460,sackOK,TS val 179204 ecr 0,nop,wscale 7], length 0 21:17:04.134566 IP corvina.vineyard.sikkerhed.org.nfs > malbec.vineyard.sikkerhed.org.1019: Flags [R.], seq 0, ack 2176607714, win 0, length 0 21:18:46.314021 IP malbec.vineyard.sikkerhed.org.43460 > corvina.vineyard.sikkerhed.org.ssh: Flags [P.], seq 128:192, ack 65, win 325, options [nop,nop,TS val 204749 ecr 427466], length 64 21:18:46.314462 IP corvina.vineyard.sikkerhed.org.ssh > malbec.vineyard.sikkerhed.org.43460: Flags [P.], seq 65:97, ack 192, win 199, options [nop,nop,TS val 457494 ecr 204749], length 32 21:18:46.314482 IP malbec.vineyard.sikkerhed.org.43460 > corvina.vineyard.sikkerhed.org.ssh: Flags [.], ack 97, win 325, options [nop,nop,TS val 204749 ecr 457494], length 0 21:18:51.317908 ARP, Request who-has corvina.vineyard.sikkerhed.org tell malbec.vineyard.sikkerhed.org, length 28 21:18:51.318177 ARP, Reply corvina.vineyard.sikkerhed.org is-at 00:9c:02:ab:db:54 (oui Unknown), length 46 mount command outputs mount.nfs4: Connection timed out mount.nfs4 10.0.0.51:/ /mnt -o soft,intr,timeo=10 0,00s user 0,00s system 0% cpu 2:05,80 total Returncode is 32 Server configuration I have enabled idmapd by adding NEED_IDMAPD=yes in /etc/default/nfs-common. Bind mounts in /etc/fstab: # nfs-audio /data/audio /exports/audio none bind 0 0 # nfs-clear /data/clear /exports/clear none bind 0 0 # nfs-video /data/video /exports/video none bind 0 0 /etc/exports: /exports 10.0.0.0/255.255.255.0(rw,no_root_squash,no_subtree_check,fsid=0,crossmnt) /exports/video 10.0.0.0/255.255.255.0(rw,no_root_squash,no_subtree_check,crossmnt) Output from # ls -al /exports total 20 drwxr-xr-x 5 root root 4096 Jul 2 14:14 ./ drwxr-xr-x 28 root root 4096 Jul 2 13:46 ../ drwxr-xr-x 7 tdn audio 4096 Jun 7 11:30 audio/ drwxr-xr-x 11 root root 4096 Jun 29 12:07 clear/ drwxrwx--- 12 tdn video 4096 Jun 7 09:46 video/

  Read the article

• YUM Update Failed - Error in POSTIN scriptlet in rpm package

  - by Tiffany Walker

  Running "yum update" and it gets to installing and then breaks. Not sure what the problem is. Google shows nothing. Error in POSTIN scriptlet in rpm package gtk2-2.18.9-10.el6.x86_64 error: error creating temporary file /var/tmp/rpm-tmp.NB84HC: Invalid argument error: Couldn't create temporary file for %post(gtk2-2.18.9-10.el6.x86_64): Invalid argument Updating : e2fsprogs-libs-1.41.12-12.el6.x86_64 44/378 Traceback (most recent call last): File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 387, in callback self._instCloseFile( bytes, total, h ) File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 463, in _instCloseFile self.base.history.trans_data_pid_end(pid, state) File "/usr/lib/python2.6/site-packages/yum/history.py", line 858, in trans_data_pid_end """, ('TRUE', self._tid, pid, state)) File "/usr/lib/python2.6/site-packages/yum/sqlutils.py", line 168, in executeSQLQmark return cursor.execute(query, params) sqlite3.OperationalError: unable to open database file error: python callback <bound method RPMTransaction.callback of <yum.rpmtrans.RPMTransaction instance at 0x45c2290>> failed, aborting! With a check all: yum check Loaded plugins: fastestmirror, rhnplugin, security MySQL-client-5.5.27-1.cp.1132.x86_64 is obsoleted by MySQL-client-5.5.27-1.cp.1132.x86_64 MySQL-server-5.5.27-1.cp.1132.x86_64 is obsoleted by MySQL-server-5.5.27-1.cp.1132.x86_64 abrt-libs-2.0.8-6.el6.x86_64 is a duplicate with abrt-libs-2.0.4-14.el6.centos.x86_64 audit-libs-2.2-2.el6.x86_64 is a duplicate with audit-libs-2.1.3-3.el6.x86_64 bandmin-1.6.1-5.noarch has missing requires of perl(bandmin.conf) bandmin-1.6.1-5.noarch has missing requires of perl(bmversion.pl) bandmin-1.6.1-5.noarch has missing requires of perl(services.conf) 32:bind-libs-9.8.2-0.10.rc1.el6_3.3.x86_64 is a duplicate with 32:bind-libs-9.7.3-8.P3.el6_2.2.x86_64 cagefs-safebin-3.6-6.el6.cloudlinux.x86_64 is a duplicate with cagefs-safebin-3.5-1.el6.cloudlinux.x86_64 chkconfig-1.3.49.3-2.el6.x86_64 is a duplicate with chkconfig-1.3.49.3-1.el6_2.x86_64 cloudlinux-release-6-6.3.0.x86_64 is a duplicate with cloudlinux-release-6-6.2.2.x86_64 coreutils-8.4-19.el6.x86_64 is a duplicate with coreutils-8.4-16.el6.x86_64 coreutils-libs-8.4-19.el6.x86_64 is a duplicate with coreutils-libs-8.4-16.el6.x86_64 1:cups-libs-1.4.2-48.el6_3.1.x86_64 is a duplicate with 1:cups-libs-1.4.2-44.el6_2.3.x86_64 1:dbus-libs-1.2.24-7.el6_3.x86_64 is a duplicate with 1:dbus-libs-1.2.24-5.el6_1.x86_64 12:dhcp-common-4.1.1-31.P1.el6_3.1.x86_64 is a duplicate with 12:dhcp-common-4.1.1-25.P1.el6_2.1.x86_64 e2fsprogs-libs-1.41.12-12.el6.x86_64 is a duplicate with e2fsprogs-libs-1.41.12-11.el6.x86_64 exim-4.80-0.x86_64 has missing requires of perl(SafeFile) expat-2.0.1-11.el6_2.x86_64 is a duplicate with expat-2.0.1-9.1.el6.x86_64 frontpage-2002-SR1.2.i386 has missing requires of libexpat.so.0 gawk-3.1.7-10.el6.x86_64 is a duplicate with gawk-3.1.7-9.el6.x86_64 glib2-2.22.5-7.el6.x86_64 is a duplicate with glib2-2.22.5-6.el6.x86_64 glibc-2.12-1.80.el6_3.5.x86_64 is a duplicate with glibc-2.12-1.47.el6_2.12.x86_64 glibc-common-2.12-1.80.el6_3.5.x86_64 is a duplicate with glibc-common-2.12-1.47.el6_2.12.x86_64 gtk2-2.18.9-10.el6.x86_64 is a duplicate with gtk2-2.18.9-6.el6.centos.x86_64 kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch is obsoleted by kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch is obsoleted by kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch is a duplicate with kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch is obsoleted by kernel-firmware-2.6.32-320.4.1.lve1.1.4.el6.noarch kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch is obsoleted by kernel-firmware-2.6.32-379.5.1.lve1.1.9.6.1.el6.noarch kernel-headers-2.6.32-379.5.1.lve1.1.9.6.1.el6.x86_64 is a duplicate with kernel-headers-2.6.32-320.4.1.lve1.1.4.el6.x86_64 keyutils-libs-1.4-4.el6.x86_64 is a duplicate with keyutils-libs-1.4-3.el6.x86_64 krb5-libs-1.9-33.el6_3.3.x86_64 is a duplicate with krb5-libs-1.9-22.el6_2.1.x86_64 libblkid-2.17.2-12.7.el6.x86_64 is a duplicate with libblkid-2.17.2-12.4.el6.x86_64 libcom_err-1.41.12-12.el6.x86_64 is a duplicate with libcom_err-1.41.12-11.el6.x86_64 libgcc-4.4.6-4.el6.x86_64 is a duplicate with libgcc-4.4.6-3.el6.x86_64 libselinux-2.0.94-5.3.el6.x86_64 is a duplicate with libselinux-2.0.94-5.2.el6.x86_64 libstdc++-4.4.6-4.el6.x86_64 is a duplicate with libstdc++-4.4.6-3.el6.x86_64 libtiff-3.9.4-6.el6_3.x86_64 is a duplicate with libtiff-3.9.4-5.el6_2.x86_64 libudev-147-2.42.el6.x86_64 is a duplicate with libudev-147-2.40.el6.x86_64 libuuid-2.17.2-12.7.el6.x86_64 is a duplicate with libuuid-2.17.2-12.4.el6.x86_64 libxml2-2.7.6-8.el6_3.3.x86_64 is a duplicate with libxml2-2.7.6-4.el6_2.4.x86_64 nspr-4.9.1-2.el6_3.x86_64 is a duplicate with nspr-4.8.9-3.el6_2.x86_64 nss-util-3.13.5-1.el6_3.x86_64 is a duplicate with nss-util-3.13.1-3.el6_2.x86_64 openssl-1.0.0-25.el6_3.1.x86_64 is a duplicate with openssl-1.0.0-20.el6_2.5.x86_64 python-2.6.6-29.el6_3.3.x86_64 is a duplicate with python-2.6.6-29.el6.x86_64 python-libs-2.6.6-29.el6_3.3.x86_64 is a duplicate with python-libs-2.6.6-29.el6.x86_64 readline-6.0-4.el6.x86_64 is a duplicate with readline-6.0-3.el6.x86_64 sed-4.2.1-10.el6.x86_64 is a duplicate with sed-4.2.1-7.el6.x86_64 tzdata-2012c-3.el6.noarch is a duplicate with tzdata-2012c-1.el6.noarch xmlrpc-c-1.16.24-1209.1840.el6.x86_64 is a duplicate with xmlrpc-c-1.16.24-1200.1840.el6_1.4.x86_64 xmlrpc-c-client-1.16.24-1209.1840.el6.x86_64 is a duplicate with xmlrpc-c-client-1.16.24-1200.1840.el6_1.4.x86_64 Error: check all Tried: #rm /var/lib/rpm/__db* #rpm --rebuilddb #yum clean all Tried also running yum-complete-transaction still won't finish the update. ls -ld /var/tmp/ drwxrwxrwt. 20 root root 12288 Oct 3 18:44 /var/tmp/ df -h /var/tmp/ Filesystem Size Used Avail Use% Mounted on /tmp 3.9G 1.2G 2.6G 32% /var/tmp Latest errors: Error: Protected multilib versions: libgcc-4.4.6-4.el6.i686 != libgcc-4.4.6-3.el6.x86_64 Error: Protected multilib versions: glibc-2.12-1.80.el6_3.5.i686 != glibc-2.12-1.47.el6_2.12.x86_64 EDITED: yum repolist Loaded plugins: fastestmirror, rhnplugin, security Loading mirror speeds from cached hostfile * cloudlinux-x86_64-server-6: cl.banahosting.com repo id repo name status cloudlinux-x86_64-server-6 CloudLinux Server 6 x86_64 10,948+725 repolist: 10,948 [~]# package-cleanup --dupes Loaded plugins: fastestmirror, rhnplugin xmlrpc-c-client-1.16.24-1209.1840.el6.x86_64 xmlrpc-c-client-1.16.24-1200.1840.el6_1.4.x86_64 bind-libs-9.7.3-8.P3.el6_2.2.x86_64 bind-libs-9.8.2-0.10.rc1.el6_3.3.x86_64 libblkid-2.17.2-12.4.el6.x86_64 libblkid-2.17.2-12.7.el6.x86_64 libtiff-3.9.4-5.el6_2.x86_64 libtiff-3.9.4-6.el6_3.x86_64 audit-libs-2.1.3-3.el6.x86_64 audit-libs-2.2-2.el6.x86_64 libstdc++-4.4.6-3.el6.x86_64 libstdc++-4.4.6-4.el6.x86_64 sed-4.2.1-10.el6.x86_64 sed-4.2.1-7.el6.x86_64 python-libs-2.6.6-29.el6_3.3.x86_64 python-libs-2.6.6-29.el6.x86_64 coreutils-libs-8.4-16.el6.x86_64 coreutils-libs-8.4-19.el6.x86_64 libudev-147-2.40.el6.x86_64 libudev-147-2.42.el6.x86_64 chkconfig-1.3.49.3-2.el6.x86_64 chkconfig-1.3.49.3-1.el6_2.x86_64 keyutils-libs-1.4-4.el6.x86_64 keyutils-libs-1.4-3.el6.x86_64 glibc-2.12-1.47.el6_2.12.x86_64 glibc-2.12-1.80.el6_3.5.x86_64 tzdata-2012c-3.el6.noarch tzdata-2012c-1.el6.noarch coreutils-8.4-19.el6.x86_64 coreutils-8.4-16.el6.x86_64 dbus-libs-1.2.24-7.el6_3.x86_64 dbus-libs-1.2.24-5.el6_1.x86_64 libxml2-2.7.6-4.el6_2.4.x86_64 libxml2-2.7.6-8.el6_3.3.x86_64 abrt-libs-2.0.8-6.el6.x86_64 abrt-libs-2.0.4-14.el6.centos.x86_64 expat-2.0.1-9.1.el6.x86_64 expat-2.0.1-11.el6_2.x86_64 python-2.6.6-29.el6.x86_64 python-2.6.6-29.el6_3.3.x86_64 gtk2-2.18.9-6.el6.centos.x86_64 gtk2-2.18.9-10.el6.x86_64 libcom_err-1.41.12-12.el6.x86_64 libcom_err-1.41.12-11.el6.x86_64 gawk-3.1.7-10.el6.x86_64 gawk-3.1.7-9.el6.x86_64 readline-6.0-4.el6.x86_64 readline-6.0-3.el6.x86_64 glibc-common-2.12-1.80.el6_3.5.x86_64 glibc-common-2.12-1.47.el6_2.12.x86_64 libselinux-2.0.94-5.2.el6.x86_64 libselinux-2.0.94-5.3.el6.x86_64 cups-libs-1.4.2-48.el6_3.1.x86_64 cups-libs-1.4.2-44.el6_2.3.x86_64 nspr-4.9.1-2.el6_3.x86_64 nspr-4.8.9-3.el6_2.x86_64 cagefs-safebin-3.5-1.el6.cloudlinux.x86_64 cagefs-safebin-3.6-6.el6.cloudlinux.x86_64 libuuid-2.17.2-12.4.el6.x86_64 libuuid-2.17.2-12.7.el6.x86_64 xmlrpc-c-1.16.24-1209.1840.el6.x86_64 xmlrpc-c-1.16.24-1200.1840.el6_1.4.x86_64 openssl-1.0.0-20.el6_2.5.x86_64 openssl-1.0.0-25.el6_3.1.x86_64 dhcp-common-4.1.1-25.P1.el6_2.1.x86_64 dhcp-common-4.1.1-31.P1.el6_3.1.x86_64 krb5-libs-1.9-33.el6_3.3.x86_64 krb5-libs-1.9-22.el6_2.1.x86_64 nss-util-3.13.5-1.el6_3.x86_64 nss-util-3.13.1-3.el6_2.x86_64 cloudlinux-release-6-6.2.2.x86_64 cloudlinux-release-6-6.3.0.x86_64 e2fsprogs-libs-1.41.12-11.el6.x86_64 e2fsprogs-libs-1.41.12-12.el6.x86_64 glib2-2.22.5-6.el6.x86_64 glib2-2.22.5-7.el6.x86_64 UPDATE 2 I removed all the dupes and then did update and got this: Updating : sudo-1.7.4p5-13.el6_3.x86_64 79/361 Error in POSTIN scriptlet in rpm package sudo-1.7.4p5-13.el6_3.x86_64 warning: /etc/sudoers created as /etc/sudoers.rpmnew error: error creating temporary file /var/tmp/rpm-tmp.hjTOqJ: Invalid argument error: Couldn't create temporary file for %post(sudo-1.7.4p5-13.el6_3.x86_64): Invalid argument Updating : pcre-7.8-6.el6.x86_64 80/361 Traceback (most recent call last): File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 399, in callback self._instCloseFile( bytes, total, h ) File "/usr/lib/python2.6/site-packages/yum/rpmtrans.py", line 475, in _instCloseFile self.base.history.trans_data_pid_end(pid, state) File "/usr/lib/python2.6/site-packages/yum/history.py", line 858, in trans_data_pid_end """, ('TRUE', self._tid, pid, state)) File "/usr/lib/python2.6/site-packages/yum/sqlutils.py", line 168, in executeSQLQmark return cursor.execute(query, params) sqlite3.OperationalError: unable to open database file error: python callback <bound method RPMTransaction.callback of <yum.rpmtrans.RPMTransaction instance at 0x5c7cfc8>> failed, aborting! - [~]# lsattr /var/tmp/ -------------e- /var/tmp/cache_5b07945563e03aec1c44917886fd99a6 -------------e- /var/tmp/sess_6edfafda1a191f6986bd020ed945eea0 -------------e- /var/tmp/sess_1b837feecdd4c9e6aa6ecd81d41fda75 -------------e- /var/tmp/sess_70bec5f392b4f5f75ac444f5c82db2dc -------------e- /var/tmp/sess_24cd226ba0a370a6d3838a37745b2e15 -------------e- /var/tmp/nginx_proxy -------------e- /var/tmp/sess_19fb1dd060e42c9de8786ef34d7fcf6e -------------e- /var/tmp/sess_b4ac777076c5122a6e27d776de0a2fcb -------------e- /var/tmp/sess_5077441775ef8d07a2185e8fd48a4aa8 -------------e- /var/tmp/cache_4e71d930fe8250e222ae4d1dc39646ff -------------e- /var/tmp/sess_eb6eb29b38b55b85303c3137611f0a2faa15c21d -------------e- /var/tmp/sess_81e7e8d93b395f2c8d7e3fe12cc59e56 -------------e- /var/tmp/sess_05c7f305bdbf9a4c7af251d33ac59766 -------------e- /var/tmp/sess_0ad9369063a37b6b399688a835d69ed2 -------------e- /var/tmp/cache_c780deda617678faeea8f8a34395ac27 -------------e- /var/tmp/sess_9773332e3c99ee18dca0b05e8f02a41e -------------e- /var/tmp/sess_1d9b02b068ea81a3975599ddc12bcfb1 -------------e- /var/tmp/sess_1ffeff444123e924834dc5e80d07571e -------------e- /var/tmp/sess_aa56725471c84d9a06745c56dc499db7 -------------e- /var/tmp/sess_51e19964d7e1a164c63f4c72fa43475c33debbc0 -------------e- /var/tmp/sess_a83c7a05bb189a465b8813ff9e566aa8f9124079 -------------e- /var/tmp/sess_2f506ba5b77c61107871e8cf80393cdb -------------e- /var/tmp/sess_7bfe1578605b259ec5e4fd2200df4cd0 -------------e- /var/tmp/sess_f6e47011789d8d48d56dd78a398d98d5719414a7 -------------e- /var/tmp/sess_b7c43a90a8b8d8f02b0fffca77796ce5 -------------e- /var/tmp/sess_6c3e7103453ad4daba815bd96a903785 -------------e- /var/tmp/sess_86f32a22507d8410b3f0fc7d71a135d5 -------------e- /var/tmp/sess_aaf72d3e8cfb2f27ffdff61323f97e7553855a05 -------------e- /var/tmp/sess_5de4488e2ee03ac0f99ab9494573ccb1 -------------e- /var/tmp/sess_716d97bba4abdb38704a9e4212f6fddc -------------e- /var/tmp/sess_534908a9510a32eda13a5dc95ac022cc -------------e- /var/tmp/sess_626a58203d93427c79621ea4fec0906d -------------e- /var/tmp/sess_827ca92d10d3797f2c187c41764a7036 -------------e- /var/tmp/sess_6282962d77f7bead20e785fbdb9a3d8f -------------e- /var/tmp/cache_b012c8a729fc54a296a700ed92930a0e -------------e- /var/tmp/sess_631e5ba769773da056108d3fbd143963 -------------e- /var/tmp/cache_30bb7f1333ba5f96a229c91a3385d8b5 -------------e- /var/tmp/sess_93e085706b29c3e4e3593bfe39b1079e -------------e- /var/tmp/sess_abd78bd6c285d681c90de8c617747ab3 -------------e- /var/tmp/sess_e144544ed925569018e6607b05f43f253f75e2aa -------------e- /var/tmp/sess_5d3d036c772847a4508d3e100b173d84 -------------e- /var/tmp/sess_f35243d1f40bd8d9ce08940fafc00d93 -------------e- /var/tmp/sess_761c3ffa811b959638ed0b266741eaa4 -------------e- /var/tmp/mm.sem.sNdxjf -------------e- /var/tmp/sess_006d45dbd807291f7bffbd1db3707ed6 -------------e- /var/tmp/cache_2d0162aac9f87c1978ac644923a5e2fe -------------e- /var/tmp/sess_22c534418c380b72d105935b59713dd1 -------------e- /var/tmp/sess_94f72ef408567a15f6287c518e93898e -------------e- /var/tmp/cache_6fe03c83bb87489f3921db1c974dfc0e -------------e- /var/tmp/sess_48bbfa2a2a8793a62c7fd6a389a2763e -------------e- /var/tmp/mm.sem.ERERMV -------------e- /var/tmp/sess_20aba82c03a69b2dc6af66c499c38ee67e27368f -------------e- /var/tmp/sess_f94fe0589a79c934815ef359bcb0a16c7080d937 -------------e- /var/tmp/sess_460390801eb004593b4dee83779f414e -------------e- /var/tmp/spamd-52811-init -------------e- /var/tmp/cache_6427fdb235d59b0b2fbd105bf23d2e87 -------------e- /var/tmp/cache_4ce12d8350d7c0361dc1bf15d552a2d8 -------------e- /var/tmp/sess_039fec2a643340f118b6355e4c836ae8 -------------e- /var/tmp/sess_fa46fa80b26e6cf3d9c7de942d5dbcff -------------e- /var/tmp/cache_664858e614367812148716536e22d030 -------------e- /var/tmp/sess_4c8d4c44fbd828dc17415ce6aa213115 -------------e- /var/tmp/sess_d231a6c0e5dd4d7bacbf9de3d8bb298f -------------e- /var/tmp/sess_a82f8a088a8e37d375f6a9fede4a54d2 -------------e- /var/tmp/sess_604697227ae5359e5783dc9407845338 -------------e- /var/tmp/sess_5b4e623536640abe671b40563d03817d -------------e- /var/tmp/sess_2aba0aff64f3c18f22e0b79d591259e2 -------------e- /var/tmp/sess_bfd52a2d2d80880f8e26ad460739a0494f0d1e9e -------------e- /var/tmp/sess_ba9f3e3a7c7111930d6b801aaa833b46 -------------e- /var/tmp/sess_5cc8c5b620015a465359359a0805fbdd -------------e- /var/tmp/sess_84945c41d604b4653a1bf45d83a1917c -------------e- /var/tmp/sess_5f52569b27430780c07d25cfb8177e5c1ef647f0 -------------e- /var/tmp/sess_45896aef9e77f16be1b3e94b3edb2599 -------------e- /var/tmp/sess_5a67d0ef8f826a2f103b429c8464bdd5f75d6218 -------------e- /var/tmp/sess_1fce98bb32e5b34c79fd5a313de32980 -------------e- /var/tmp/sess_f7ea772ff3fbb1eb2ad8712dd2c49ed8 -------------e- /var/tmp/sess_a9dc16bc5c1eb2768bb2600f0d102fde -------------e- /var/tmp/mm.sem.3zwRTu -------------e- /var/tmp/sess_e2cad140703338a4b8c9254ec6b0a1a2 -------------e- /var/tmp/sess_e7c8e85daf9c5424aecb83e066decf31 -------------e- /var/tmp/sess_800f878fa944370f42e76057e7c033e19520bd41 -------------e- /var/tmp/sess_4fdae64eb18599521ace18679795568b -------------e- /var/tmp/sess_958fb886b97de2e767b059376c4724b5 -------------e- /var/tmp/sess_3c832a31f17744a8bb3c59dde02e561aefbc2e48 -------------e- /var/tmp/sess_6d9d7bf04f34e0d82b101f882196a905 -------------e- /var/tmp/sess_7231c75ae4fad2ca5fbcb6de430a7b13 -------------e- /var/tmp/sess_2eadffa2285def9673ce784395d272d8 -------------e- /var/tmp/cache_2ff353b664d8028df967f807ac18593a -------------e- /var/tmp/sess_4138a267f1f5e3ad93c1d64547c63134ae7c0db3 -------------e- /var/tmp/sess_64cd9fa0d6af8e8041aafffbe3db986a -------------e- /var/tmp/tmpg3ycIG -------------e- /var/tmp/cache_b633ac8283d6de8e39d81160d63fc8cd -------------e- /var/tmp/sess_2cee03cf5eafd3ef55d8efa1b0390436 -------------e- /var/tmp/sess_608066c609e28621f2a29ac04a3a6441 -------------e- /var/tmp/sess_46dfb35cf8266699ba9304e5d8c6869d -------------e- /var/tmp/sess_fb202a0ed54cee8832c5f6e0ca7fc1b3 -------------e- /var/tmp/sess_8fe3c5fd8cdda02855e5f9b5a1ea85a4 -------------e- /var/tmp/sess_941376d5cb51e0ba73f9a27ee259c159 -------------e- /var/tmp/sess_4fa17b1eac1d18341d20d0d8d4991ceb -------------e- /var/tmp/cache_de647c956ca6a1b75744ad194aceaa82 -------------e- /var/tmp/mm.sem.Ugu7Be -------------e- /var/tmp/sess_656e8a50759d5b36b963e7eb85e0bb0d -------------e- /var/tmp/sess_983f77b607bbffa1748d6c49557381e9 -------------e- /var/tmp/sess_632860d092e5e374da522ed2f88e83ce -------------e- /var/tmp/sess_030f900b81cc2a4ad095d53ef3ee0791 -------------e- /var/tmp/yum.log -------------e- /var/tmp/cache_810174993c6a2c0efe2edbe4c39a4a81 -------------e- /var/tmp/sess_29e2c781643434e81d189fc41f47fd34 -------------e- /var/tmp/tmpE12ahd -------------e- /var/tmp/sess_935da512fb077e04610266748b3b77f3 - cat /etc/fstab /tmp as: loop,rw,noexec,nosuid,nodev

  Read the article

• Implement QoS/Bandwidth Management or Upgrade Bandwidth?

  - by Michael

  A question that I'm faced with currently. Here's my setup: Cisco ASA 5510 15Mbps Internet Connection @ $1350/month The bandwidth was originally meant for 35-45 people but we've grown quite quickly to roughly 60-65 people. Needless to say, when I check bandwidth logs it's almost always spiked at 15Mbps. I did use Wireshark to do some poking around to see what was hogging up our bandwidth but with everything running through CDNs and Cloud Services it proved difficult to get a good grasp of where our bandwidth was going. So the question is do I ONLY implement bandwidth management through ASA OR upgrade the Internet to 50Mbps ($1600/month) and then implement bandwidth management through ASA? Any suggestions on how to segment the 15Mbps connection if we decided ONLY to go with the bandwidth management solution? Thanks. UPDATE 1 Installed PRTG and used packet content to monitor the traffic. As I suspected still pretty vague. My Top Connections include the following: a204-2-160-16.deploy.akamaitechnologies.com ec2-50-16-212-159.compute-1.amazonaws.com a204-2-160-48.deploy.akamaitechnologies.com a72-247-247-133.deploy.akamaitechnologies.com mediaserver-sv5-t1-1.pandora.com Other than the Pandora destination, the rest doesn't tell me much on how to properly control the bandwidth. Any thoughts or suggestions? Thanks. M

  Read the article

• How to figure out how much RAM each prefork thread requires for maximum Wordpress performance on an EC2 small instance

  - by two7s_clash

  Just read Making WordPress Stable on EC2-Micro In the "Tuning Apache" section, I can't quite figure out how he comes up with his numbers for his prefork config. He explains how to get the numbers for an average process, which I get. But then: Or roughly 53MB per process...In this case, ten threads should be safe. This means that if we receive more than ten simultaneous requests, the other requests will be queued until a worker thread is available. In order to maximize performance, we will also configure the system to have this number of threads available all of the time. From 53MB per process, with 613MB of RAM, he somehow gets this config, which I don't get: <IfModule prefork.c> StartServers 10 MinSpareServers 10 MaxSpareServers 10 MaxClients 10 MaxRequestsPerChild 4000 </IfModule> How exactly does he get this from 53MB per process, with 613MB limit? Bonus question From the below, on a small instance (1.7 GB memory), what would good settings be? bitnami@ip-10-203-39-166:~$ ps xav |grep httpd 1411 ? Ss 0:00 2 0 114928 15436 0.8 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1415 ? S 0:06 10 0 125860 55900 3.1 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1426 ? S 0:08 19 0 127000 62996 3.5 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1446 ? S 0:05 48 0 131932 72792 4.1 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1513 ? S 0:05 7 0 125672 54840 3.1 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1516 ? S 0:02 2 0 125228 48680 2.7 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1517 ? S 0:06 2 0 127004 55796 3.1 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1518 ? S 0:03 1 0 127196 54208 3.0 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf 1531 ? R 0:04 0 0 127500 54236 3.0 /opt/bitnami/apache2/bin/httpd -f /opt/bitnami/apache2/conf/httpd.conf

  Read the article

• Slow VM on esxi 4.1

  - by user57432

  We have a FreeBSD 64bit running on a esxi 4.1, the hardware platform is a DELL R710 with 2 x 56xx (intel 6core cpu) and 48 GB ram. The FreeBSD vm is very slow, when we compiles/builds something on it, it takes 5 minuts and it says "build time 18 seconds.". There's no vmtools installed on the vm. The same vm is installaed on another R710 running esxi 4.0 for dell and there's no problems with that one. Does anyone have any idea about what to look for? the VMs on the second server (ESXi 4.1) is a clone of the VMs running on the first VMserver (ESXi 4.0 Dell edition). It's not possible for me to move the VM back to the first server since the file contaning the vm is too big. We installed the new esxi with a datasore with 8mb blocks because 1mb blocks dident allow for the file size we needed. It looks like the www server on the new ESXi 4.1 works fine, but I havent really tested it. There's not installed vmtools on any of the VMs (FreeBSD). The block size on the second VM (ESXi 4.1) datastorage is 8mb and 1mb on the first (ESXi 4.0)

  Read the article

• Use synergy with Physical KVM

  - by Mr. Man

  I am using synergy on a Linux Mint computer as the server with a Mac as the client. I also have a physical KVM switch. The problem I have is that when ever I switch the physical KVM to my Mac, synergy stops working as in the keyboard and mouse don't work with the Mac. Thanks in advance! EDIT: here are some logs: From the Mint machine: INFO: synergys.cpp,1042: Synergy server 1.3.1 on Linux 2.6.31-14-generic #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 i686 DEBUG: synergys.cpp,1051: opening configuration synergy.conf DEBUG: synergys.cpp,1062: configuration read successfully DEBUG: CXWindowsScreen.cpp,847: XOpenDisplay(:0.0) DEBUG: CXWindowsScreenSaver.cpp,339: xscreensaver window: 0x00000000 DEBUG: CXWindowsScreen.cpp,117: screen shape: 0,0 1024x768 DEBUG: CXWindowsScreen.cpp,118: window is 0x03800004 DEBUG: CScreen.cpp,38: opened display DEBUG: CXWindowsScreen.cpp,679: registered hotkey F12 (id=efc9 mask=0000) as id=1 NOTE: synergys.cpp,500: started server INFO: CServer.cpp,1141: screen ubuntu shape changed NOTE: CClientListener.cpp,127: accepted client connection DEBUG: CClientProxy1_0.cpp,404: received client marks-mac.local info shape=-1024,0 2304x800 NOTE: CServer.cpp,278: client mac has connected INFO: CServer.cpp,447: switch from ubuntu to mac at -1024,393 INFO: CScreen.cpp,116: leaving screen DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWinavDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG302)DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDE47DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsrset=utf-8 (633), text/plain (462) DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added f DEBUG: CXWindCXWDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG:SerDEBUG: CXWindowsClipboard.cpp,555: ed DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555owsClDEBUG: CXWindowsClipboard.cpp,555: 1DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: getDEBUG: CXWindowsClipboard.cpp,555: added f DEBUG: CXW8_STDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added fD textDEBUG: CXWindowsClipboard.cpp,555: added fDEBU DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipinDEBUG: CXWindowsClipboard.cpp,555:oardDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindCXWDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG:SerDEBUG: CXWindowsClipboard.cpp,555: ed DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555owsClDEBUG: CXWindowsClipboard.cpp,555: 1DEBUG: CXWindowsClipboard.cpp, s From the Mac: connecting to '192.168.3.5': 192.168.3.5:24800 connected to server entering screen leaving screen entering screen leaving screen stopped client

  Read the article

• Network cabling with multiple patch panels?

  - by dannymcc

  I am in the very early stages of planning a network cabling upgrade in our office, mainly to upgrade the old cables from Cat5 to either 5e or 6. I am also planning on upgrading all of our 10/100 switches to 10/100/1000 switches. I would like to have three small wall mounted cabinets spread around the building, each with a patch panel and switch. These would all lead back to our server room. The question is; should I have two patch panels in each wall cabinet, one with 24 or 48 ports that are connected to a matching patch panel in the server room. The second patch panel would then link to each device in that cabinets area. Then I wouldn't put a switch in the small cabinets. All switching would be done in the server room. Or, should I have one main cable from the server room to each of the cabinets - plugged straight into the switch and the patch panel is for devices in the cabinets area? I hope that makes sense!

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >