Search Results

Search found 1672 results on 67 pages for 'grub'.

Page 42/67 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• ubuntu 12.04 with windows 8 dual boot not booting

  - by Nick

  I followed the procedure mentioned at Installing Ubuntu on a Pre-Installed Windows 8 (64-bit) System (UEFI Supported) on toshiba satellite laptop. also tried the boot-repair and logs @ http://paste.ubuntu.com/6327398/ Its not booting to windows as well as ubuntu. It goes to grub command prompt. When on initial screen it briefly shows error message as failed to open /efi/Microsoft/boot/grubx64. Please advise. EDIT : Secure boot in on and boot mode is UEFI Boot

  Read the article

• Misused mke2fs and cannot boot into system

  - by surlogics

  I installed Ubuntu with WUBI in Windows 7 64bit, and I had installed Mandriva 2011 with a disk. I tried to learn Linux with Ubuntu and misused mke2fs; after I reboot my computer, Windows 7 and Ubuntu has crashed. As I have Mandriva, I boot into Mandriva and found # df -h /dev/sda7 12G 9.8G 1.5G 88% / /dev/sda2 15G 165M 14G 2% /media/logical /dev/sda6 119G 88G 32G 74% /media/2C9E85319E84F51C /dev/sda5 118G 59G 60G 50% /media/D25A6DDE5A6DBFB9 /dev/sda9 100G 188M 100G 1% /media/ae69134a-a65e-488f-ae7f-150d1b5e36a6 /dev/sda1 100M 122K 100M 1% /media/DELLUTILITY /dev/sda3 98G 81G 17G 83% /media/OS # fdisk /dev/sda Command (m for help): p Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd24f801e Device Boot Start End Blocks Id System /dev/sda1 2048 206847 102400 6 FAT16 /dev/sda2 * 206848 30926847 15360000 7 HPFS/NTFS/exFAT /dev/sda3 30926848 235726847 102400000 7 HPFS/NTFS/exFAT /dev/sda4 235728864 976771071 370521104 f W95 Ext'd (LBA) /dev/sda5 235728896 481488895 122880000 7 HPFS/NTFS/exFAT /dev/sda6 727252992 976771071 124759040 7 HPFS/NTFS/exFAT /dev/sda7 481500243 506674034 12586896 83 Linux /dev/sda8 506674098 514851119 4088511 82 Linux swap / Solaris /dev/sda9 514851183 727246484 106197651 83 Linux Partition table entries are not in disk order I think I may used the following command mke2fs -j -L "logical"/dev/sda2 but I had forgotten what kind of partition it was before I transfered it into ext3. perhaps ntfs Data was not lost, and I can view my files as I could in Windows. In Mandriva, there are following disks: 117.2 GB hard disk, files in it is the same as my Windows D:, and Ubuntu was installed in it; 119.0 GB hard disk is my G:, with my personal files in it; 12.0 GB is the same with Mandriva / (with means root), 101.3 GB hard disk with nothing but lost+found; DELLUTILITY should be Dell computer utilities pre-installed in my computer; logical is the disk which I had spoiled, I can view nothing but lost+found; and OS is the C: in my Windows. After I boot, grub lets me choose Mandriva or Windows. I chose Windows and it tells me: FILE system type unknown, partition type 0x7 Error 13: Invalid or unsupported executable format I doubt something wrong with windows MBR or something # cat /boot/grub/menu.lst timeout 5 color black/cyan yellow/cyan gfxmenu (hd0,6)/boot/gfxmenu default 0 title linux kernel (hd0,6)/boot/vmlinuz BOOT_IMAGE=linux root=UUID=199581b7-ac7e-4c5f-9888-24c4f213cad8 nokmsboot logo.nologo quiet resume=UUID=34c546e4-9c42-4526-aa64-bbdc0e9d64fd splash=silent vga=788 initrd (hd0,6)/boot/initrd.img title linux-nonfb kernel (hd0,6)/boot/vmlinuz BOOT_IMAGE=linux-nonfb root=UUID=199581b7-ac7e-4c5f-9888-24c4f213cad8 nokmsboot resume=UUID=34c546e4-9c42-4526-aa64-bbdc0e9d64fd initrd (hd0,6)/boot/initrd.img title failsafe kernel (hd0,6)/boot/vmlinuz BOOT_IMAGE=failsafe root=UUID=199581b7-ac7e-4c5f-9888-24c4f213cad8 nokmsboot failsafe initrd (hd0,6)/boot/initrd.img title windows root (hd0,1) makeactive chainloader +1 I can boot into Linux, but not Ubuntu, it boot into Mandriva. I don't have a boot disk. Help me find a way to make it work again.

  Read the article

• Graphics on ubuntu 12.04 not working

  - by Rhavin

  I've got a new build specs: i5 3570k gigabyte z77 d3h Using integrated graphics I've managed to install Ubuntu 12.04 with the alternate installer, and to get video with the nomodeset option on grub screen. However when I log in, I only get the 4:3 display option. I can't get it to change. Under the settings:details tab it recognizes the hd4000 integrated graphics. Hoping someone could help!

  Read the article

• stuck in busybox after update

  - by Lyra500

  I should start out by saying that I am not very tech savvy and have done my best to understand what is going on here from reading other people's posts and have fumbled my way through several attempted fixes without getting anywhere... I run ubuntu 12.04 on an admittedly cheap laptop from ebuyer and in spite of being cheap and not a brand laptop I have never had any major problems with it. Since updating to 12.04 when it was released the boot-up process has always been slow. Logging in takes about 30secs longer than it used to and if I closed my laptop and opened it again instead of being met with a login screen I'd be met with a black screen with a white mouse. As all of these problems had a behavior-changing fix (don't close laptop, patiently wait for login, etc.) I didn't think of reporting any of the issues. Last night when the update manager prompted me that there were updates available I duly did them as I usually do. At the time a bug report came up and I cannot remember what it said but I reported the bug as I was prompted to do. Then this morning when I started up my laptop it went through the usual sequence, GRUB, purple screen with 'ubuntu' etc. and then when it tried to boot up it went into BusyBox and I have not been able to do anything to solve this. I have tried going into the GRUB menu and starting previous versions but I come to the same point - busybox. I have borrowed another rather elderly laptop with Windows Vista to try and download Boot Repair and Ubuntu and burn them onto CD. I tried downloading boot repair five times, to laptop, CD and USB. Every time it would download and burn fine but then the windows laptop would tell me that 1% did not download properly and my laptop would not run the USB or CD upon booting. I then tried to download ubuntu and make a livecd, twice, but again was told that 1% did not download properly and again my laptop will not run ubuntu from the CD upon booting even if/when I went into the f2 menu and changed the menu priority (if that's what you call it) for booting up to make sure it was definitely trying the USB/CD first. This is the message I get from busybox: BusyBox v1.18.5 (Ubuntu 1:1.18.5-1ubuntu4) built-in shell (ash) Enter 'help' for a list of built-in commands I have tried 'exit' but it mentions things about 'kernal panic' and 'tried to quit init!' and 'can't find /root/dev/console : no such file'. I know that the problem is probably caused by a problem with a kernal caused by the update last night, but I couldn't honestly tell you exactly what was updated and without being able to boot from a livecd I'm not sure how to go about fixing this. As I said, I am not tech savvy and have done what I can to try and find a solution to the problem but I'm starting to feel like I'm out of options. Does anyone have any ideas?

  Read the article

• have to plug/un-plug usb devices on system booting?

  - by user866581

  it's so weired that i have to plug/unplug in my usb devices every time booting ubuntu. it happens for both installing ubuntu and booting ubuntu (10.10 and 11.10) the scenario is like: 1.bios checking - 2.grub start - 3.keyboard & mouse led OFF (black screen with a cursor on top-left) - 4.i plug/unplug in any usb devices - 5.everything is back to normal and ubuntu started it's really frustrating :( please advise the solution.

  Read the article

• Ubuntu 13.10 problems

  - by user198097

  I have two problems with new Ubuntu 13.10. 1, Black screen problem: - Between GRUB and loading screen adopts black screen for 10 minutes and between the loading screen and the desktop appearance is a black screen for 20-30 seconds. 2, Wake problem: - After the suspension is to move the keyboard does not work or I can not do anything about it, because nothing works. 3, Full screen problem - When I back from full screen, I can't see the Unity, instead I see the window. :/ Please help me.

  Read the article

• Stop Windows boot

  - by Parley Applegate

  Installed Ubuntu over a Windows8 trial. After installation, Windows8 still tries to boot. Wiped disk clean with Acronis and reinstall Ubuntu. Windows8 still tries to start, but goes to blank screen. Ubuntu never tries to boot. Naturally live mode works fine. What do you think of wiping disk again, install Windows7 and try using GRUB approach or do you know how to remove Windows from the cleaned disk?

  Read the article

• Cannot pass the login screen after upgrade to 12.04 from 11.10

  - by joksan

  I just performed the upgrade from Ubuntu 11.10 to Ubuntu 12.04 LTS. The updater downloaded all packages but a few ones that the system said were already installed. When asked for it, I chose to install the new maintainer's version of grub. Now after that my system start up to the login page, some images won't load. Moreover, after I try to login, the graphical instance does not load, it just sits there showing the mouse pointer and nothing else.

  Read the article

• 'mount: error while loading shared libraries: libudev.so.0 : no such file or directory' error while booting

  - by user199551

  I was trying to load a version of CGminer which was returning a libudev type error, and followed a supposed solution here but it destroyed my system (so it seems). I loaded the system in recovery mode from GRUB but all that done was actually tell me what I something is broken, do not know what to do next. I think I somehow associated a libudev.so.0 to 1 or 1 to 0, I am not sure what I did and how to fix it.

  Read the article

• Cannot boot into Ubuntu after installing Ubuntu 12.04 (with Windows 7 on another partition)

  - by onezanygirl

  I just installed Ubuntu on my desktop which had Windows 7 installed on it. When I restart the machine after completing the installation, It directly loads windows, I don't see the grub menu. I tried using boot-repair using the LiveCD (both recommended fixes AND fixing the MBR), it did not help. What am I missing? I have done this at least 5 other times, on different machines, and have never faced this issue before.

  Read the article

• Cannot boot from USB wtih ubuntu 13.10

  - by arunkant

  I downloaded ubuntu 13.10 amd64 iso and used all of following methods to make a install media. UNetBootin Universal USB installer (from windows) But I cannot boot from USB pen drive. Some time it just drop me in grub menu of previously installed ubuntu 13.04. Sometime it show a message "Could not open //fallback.efi: 14 ..." for a moment and then just stays there(blank screen). How to boot from USB pen drive?

  Read the article

• Windows NT from vmware to kvm

  - by Luca Rossi

  I'm trying to convert a couple of old Windows NT virtual servers from vmware to KVM. I tried almost all guidelines and how to I found around the web but with no luck. I have the vmware virtual disk: Dlc1.vmdk partitioned image. I converted the vmdk into qcow2 image with the qemu utility and I tried to use it with kvm: kvm -hda test.qemu -vnc :1 -m 750 but I receive "error loading operating system" I also tried with raw partitions I can mount through losetup and kpartx. but nothing changed I also tried to create an brand new image file with: qemu-img create -f qcow2 test.qcow2 2G I partitioned the new image file and I copied the original partition 1 to the new partition 1 with dd: dd if=/dev/mapper/loop1p1 of=/dev/mapper/loop0p1 bs=128M no luck again I also tried with a single unpartitioned file: qemu-img create -f qcow2 test.qcow2 2G and I copied the partition 1 to the new image file: dd if=/dev/mapper/loop0p1 of=test.img bs=128M but when booting, I receive a black screen and the virtual machine hangs. The bootloader is loaded successfully, because I also tried with a GRUB live iso and I receive the same screens and errors. Note that grub sees the Windows setup and give me the boot choice. I have the suspect the problem is that the vmware machine is probably a scsi guest and in centos 6 (my system) scsi emulation is no longer supported. But in that case, where to change in Windows? I'm not so skilled with MS systems. Thank you for the help Luca Rossi

  Read the article

• ASUS P8B WS - Endless Reboots

  - by tuxGurl

  I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

  Read the article

• Ubuntu 10.04 Keyboard and Mouse Freezing Problem

  - by nitbuntu

  I had a partition setup with Windows XP and Ubuntu 8.04 dual booting. I recently upgraded to Ubuntu 10.04 by installing fresh from CD but leaving the previous /home folder as is. Things seemed to be working fine, but started finding that my mouse and keyboard were freezing. After a quick search on the internet, I found the following suggestions as shown here:- Ubuntu Forums Here the suggestion was to:- Edit /etc/default/grub, go to the line that begins like: GRUB_CMDLINE_LINUX_DEFAULT= Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=off" After that, run this command: sudo update-grub and Reboot This seemed to have resolved the issue but after a couple of days I again find my mouse and keyboard freezing. I also find that my parallel port printer had also stopped working. I have saved the output of dmesg and my syslog. The first can be viewed here but the syslog had too many characters, so if someone can suggest an alternative to freetexthost, I can post it there. Moreover, if there is any other information that should be provided, do let me know. I do hope we can get to the bottom of this issue. Thank you in advance for any help that could be provided.

  Read the article

• Windows 7 doesn't boot when second hard disk is connected

  - by kenshin9786

  I'm sorry for my bad english on beforehand. I have two hard disks, one SATA and another IDE. I have windows XP and 7 on the SATA one, and Ubuntu on the IDE. Both of them boots and works, bios recognizes them, just works. After I installed Windows 7, and connected the IDE drive, it freezes on "Starting Windows" (the black screen with the Windows logo). I unplug the IDE drive, and it starts normally. Windows XP starts normally on both situations (with or without the IDE one connected), same for Ubuntu (it works with both disks connected or just the IDE where it is). The IDE drive is on good status according to SMART. The IDE is first on boot order. It goes to the Ubuntu's grub first, then by default it goes to the Windows 7 bootloader, and then to XP. I think the problem is not about the bootloader or grub. I just read that it can be solved formatting the "problematic" hard disk because Windows 7 cannot handle so many active partitions or something like that. But that's not an option for me, I don't want to lose my Ubuntu nor have it unbootable. How can I solve this without this consecuences I mentioned? Any help would be appreciated.

  Read the article

• OpenVZ Can't initialize containers after install

  - by Tonino Jankov

  I have installed OpenVZ on centos 6 on a dedicated server. I followed quick installation guide on openvz wiki. After installing thru yum, I don't know why, but grub.conf wasn't automatically updated to accomodate new kernel, so I had to do it manually. I edited grub.conf, added openvz kernel and rebooted - it went fine. Server went up into openvz kernel and it worked, it started openvz service byitself. But after I created a container, added IP to it and attempted to start it, I couldn't. Here is the output from the shell: [root@cloud2 ~]# vzctl start 86 Starting container ... Container is mounted Container start failed (try to check kernel messages, e.g. "dmesg | tail") Container is unmounted [root@cloud2 ~]# dmesg | tail [ 1973.401596] CT: 86: failed to start with err=-105 [ 2107.113850] Failed to initialize the ICMP6 control socket (err -105). [ 2107.155523] CT: 86: stopped [ 2107.155543] CT: 86: failed to start with err=-105 [ 6348.282184] Failed to initialize the ICMP6 control socket (err -105). [ 6348.330348] CT: 86: stopped [ 6348.330361] CT: 86: failed to start with err=-105 [45184.024002] Failed to initialize the ICMP6 control socket (err -105). [45184.072086] CT: 86: stopped [45184.072099] CT: 86: failed to start with err=-105 [root@cloud2 ~]# I don't know what is wrong. I tried different templates, debian 6, centos 6, i386, amd64, but the issue is the same. What is the problem?

  Read the article

• Install Windows 7 from ISO image

  - by Albert

  Hi, I have an ISO file of the Windows 7 DVD and I want to install it on my PC which currently only runs Linux. I don't have any DVD drive. I have some unpartitioned space on one disk where I want to install it in. When I am doing this for Linux, I usually just create the partitions from the running system, format them, mount them, copy files over, chroot into it, setup the stuff and I can boot into it (or I use some of the uncountable available scripts which do exactly that automatically). However, I have no idea how to do the same thing with Windows. So far, I tried with VMware, i.e. I gave it direct full access to the disk where I want to install it in, installed it there, then tried to boot natively into it. The Windows logo showed up but after maybe 3 seconds or so, it crashes. Safe mode also crashes. I already expected that this probably would exactly behave the way it does right now because I have heard that Windows is quite sensible about hardware changes (i.e. the VMware hardware and the real hardware). However, how can I fix it now that it works? Or I could also just delete it again and try just over. But how exactly? I also searched for ways to boot directly into an ISO file. There seem to be ways to do that via GRUB (and maybe some additional boot loader), although quite complicated. I already tried one method (GRUB: map ...iso (hdX)), however, that didn't worked. Also, even if it does work, I will get into trouble when I boot into the newly installed Windows and it requests for the DVD (because it does that at the first boot into the new system). Seems all quite complicated. Isn't there some easy way like I would do it for Linux? Or what would be the easiest way to get what I want?

  Read the article

• Missing MB on a GPT partioned SSD

  - by pisswillis

  I recently installed Arch Linux on an Intel 40GB SSD. I used GPT for partioning (via GNU parted) and created the following partions: /dev/sda1 : 1 MB, no FS, flag=bios_grub /dev/sda2 : 30MB, /boot, ext2, flag=boot /dev/sda3 : 20GB, /home, ext4 /dev/sda4 : ~20GB, /, ext4 After struggling to install grub2 from the livecd environment (which I finally did via grub-install /dev/sda --root-directory=/mnt/ --no-floppy --force) I got a working system. However, when I was inspecting disk usage with df I noticed that my home partition had around 170MB of used space on it. This surprised me because the only things on /home were one users .bashrc, .bash_history, and .lesshst. du confirmed that there was only a few KB of space being used on /home. Why does df report approximately 170MB being used when du does not? Is this space "gone forever", or can I regain it by repartioning and/or reinstalling? When I installed grub2 it said something along the lines of "your embed area is too small", and that I could "use BLOCKLISTS, but BLOCKLISTS are UNRELIABLE". In the end the only way I could get a system booting from the SSD was to use blocklists via the grub-install --force flag. Is this related to the mysterious missing 170MB? Thanks

  Read the article

• drivers/rtc/hctosys.c: unable to open rtc device (rtc0) after recompile on boot

  - by squareone

  After recompiling a new kernel on CentOS 6.3, using the same kernel I have been using on several other machines, I am getting a kernel panic on two machines. I get the following when trying to boot: drivers/rtc/hctosys.c: unable to open rtc device (rtc0) (flashes this before displaying the panic below) not syncing: Attempted to kill init! exitcode=0x00000100 Pid: 1, comm: init Not tainted etc... I have been trying to figure out what is going on, and am having trouble doing so, and feel I have exhausted all of my options here. Any help would be appreciated. My grub.conf: default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (3.4.18-rt29) root (hd0,0) kernel /vmlinuz-3.4.18-rt29 ro root=/dev/mapper/VolGroup-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_NO_MD rd_LVM_LV=VolGroup/lv_swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet panic=5 initrd /initramfs-3.4.18-rt29.img title CentOS (2.6.32-279.14.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-279.14.1.el6.x86_64 ro root=/dev/mapper/VolGroup-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_NO_MD rd_LVM_LV=VolGroup/lv_swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet panic=5 initrd /initramfs-2.6.32-279.14.1.el6.x86_64.img Any help or guidance would be greatly appreciated.

  Read the article

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

  - by flight

  A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

  Read the article

• Encrypted Windows 7 & Linux Advice Wanted

  - by Miles

  I would like to set up my laptop to dual boot Arch Linux and Windows 7 with file sharing and encryption. Just wanted some advice on going about this because I have not dealt with encryption nor file sharing. I have two 500GB hard drives, and this is my plan: Install Windows 7 across both hard drives Use a live CD to wipe out Windows boot loader and replace with Grub Legacy Use live CD to wipe out second hard drive and re-size the Windows partition located on first hard drive Install Arch Linux along side with Windows 7 on first hard drive, all remaining space goes to home folder as ext2 Install truecrypt and ext2fsd Concerns: Is this the most efficient way to share files between both OSes? Or should I just be using NTFS to store all my data? How would the file permissions work when sharing files between Windows and Linux? Is there a high likley hood of corruption, and what is the ease of backing up files from an encrypted disk? Anything I should look out for, conflict between Grub and Truecrypt? Thank you for any advice, and feel free to post any links you might find useful to me. I am trying to plan this out so I can minimize downtime as I do not want to spend more than a night on this, nor do I want to run into a major problem some time in the future.

  Read the article

• Windows 7 BSOD, safe mode working,

  - by mil0ck

  I need help getting my dualboot with Windows 7 and Ubuntu 12.04 to work, and since I'm not to experienced with computers I've been pretty dumb. Here's what I've done, quite shortend though: First removed a Ubuntu 10.04 partion, and replaced bootloader using EasyBCD Installed Ubuntu 12.04 on same partion as before Decided I need more space so I shrinked my C: partion (Windows partion) using Here, after rebooting my computer, I was stuck a grub rescue, when booting up the computer I fixed that by using SuperGrubDisk Rescatux and then using my Windows Vista install disk to repair the computer (computer is using Windows 7) I know re-installed Ubuntu 12.04 on the linux partion and got the GRUB-bootloader working Then, after using my computer for several hours, I installed beta drivers (version 304.79) for my GeForce GTS 240 and then rebooted my computer. At the first boot (after reboot) my computer just crashed, and here I am When trying to boot Windows 7 now I get a Blue Screen Of Death. I can though boot in to safe mode with everything working. I have uninstalled the beta drivers and installed the same one as before but still the same problem. I have tried all the commands in Bootrec.exe and none is working. I can't neither find an OS when using Bootrec.exe/ScanOs. I have also tried running: sfc/scannow and that comes out clean. Short: My harddrive and files seems to be intact but when booting I get bluescreen. I can though boot in to safemode with everything working. I need help Thanks to anyone who even took the time to read that. //mil0ck

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• Ubuntu loading stops ?

  - by joxnas

  I don't know why, or how... but my ubuntu's loading / booting stops right after the ubuntu logo appearing.. An underscore appears in the right top of the screen: _ then, it disappears leaving the whole screen black Version is 9.10 ,Kernel is .20 I have tryed recovering mode and selected recover damaged packages option, but it didn't do any good.. I have very important files in Ubuntu that I need to copy to a pen drive or something, today.. The terminal mode is working, so i think i can do this there.. My questions: How can I get my Ubuntu to load? Is it possible to copy the files i need via terminal mode? I dont know if with other of the previous kernels it would work... but I had configured my grub (inside Ubuntu's gui) to show only the last kernel... and now i can't select any other kernel then .20 because I don't know a way to configure Grub unless via Ubuntu's gui... My hardware: ATI Mobility Radeon 4650 HD P7450 2.13Ghz Core duo 4Gb DDR2

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >