Search Results

Search found 1285 results on 52 pages for 'lossless compression'.

Page 42/52 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

  • Codec Problems with trying to edit videos with VirtualDub

    - by Roy Rico
    So, I'm a little frustrated. According to this post and various other internet sources, virtualdub is supposed to allow users to quickly split and join video files. I am using windows 7 64 Bit and the latest version of VirtualDub (64-bit). I have tried to edit various movie files, and each attempt at editing various files I have done has not worked for me. AVI file A.avi won't load, saying that it can't located the Decompressor for the "FMP4" format. I have tried this solution and this one, and neither of them work. I have tried setting the VFW Decompressor for 'Other MPEG4' setting to XVID or LIBAVCODEC. There is no change in virtual dub AVI file C.avi will load in Virtual Dub, but any attempt to split it gives me an error that I don't have XVID codecs installed. I've attempted to install the proper codecs (Shark's Windows 7 Codecs, CCCP) with no change. AVI file C.avi will load, and it will split, but won't split using the "Direct Stream Copy" claiming the compression algorithm is incompatible. I tried "Fast Recompress" option and it created a 27GB file out of what was supposed to be about a 300-400MB file. Can someone please give me some insight into what I'm messing up?

    Read the article

  • Git fails to push with error 'out of memory'

    - by jwir3
    I'm using gitosis on a server that has a low amount of memory, specifically around 512 MB. When I try to push a large folder (happens to be a backup from an android phone), I get: me@corellia:~/Configs/$ git push origin master Counting objects: 18, done. Delta compression using up to 8 threads. Compressing objects: 100% (14/14), done. fatal: Out of memory, malloc failed MiB | 685 KiB/s error: pack-objects died of signal 13 error: failed to push some refs to 'git@dagobah:Configs' I've been searching the web, and notably found: http://www.mail-archive.com/[email protected]/msg01747.html as well as http://git.661346.n2.nabble.com/Out-of-memory-error-during-git-push-td5443705.html but these don't seem to help me for two reasons: 1) I am not actually out of memory when I push. When I run 'top' during the push, I get: 24262 git 18 0 16204 6084 1096 S 2 1.2 0:00.12 git-unpack-obje Also, during the push if I run /head/meminfo, I get: MemTotal: 524288 kB MemFree: 289408 kB Buffers: 0 kB Cached: 0 kB SwapCached: 0 kB Active: 0 kB Inactive: 0 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 524288 kB So, it seems that I have enough memory free, but it's actually still failing, and I'm not enough of a git guru to figure out what is happening. I would appreciate it if someone could give me a hand here and tell me what could be causing this problem, and what I can do to solve it. Thanks! EDIT: The output of running the ulimit -a command: scottj@dagobah:~$ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 204800 max locked memory (kbytes, -l) 32 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 10240 cpu time (seconds, -t) unlimited max user processes (-u) 204800 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

    Read the article

  • Why is OpenSSH not using the user specified in ssh_config?

    - by Jordan Evens
    I'm using OpenSSH from a Windows machine to connect to a Linux Mint 9 box. My Windows user name doesn't match the ssh target's user name, so I'm trying to specify the user to use for login using ssh_config. I know OpenSSH can see the ssh_config file since I'm specifying the identify file in it. The section specific to the host in ssh_config is: Host hostname HostName hostname IdentityFile ~/.ssh/id_dsa User username Compression yes If I do ssh username@hostname it works. Trying using ssh_config only gives: F:\>ssh -v hostname OpenSSH_5.6p1, OpenSSL 0.9.8o 01 Jun 2010 debug1: Connecting to hostname [XX.XX.XX.XX] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa-cert type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa type 2 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debia n-3ubuntu5 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname' is known and matches the RSA host key. debug1: Found key in /cygdrive/f/progs/OpenSSH/home/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa debug1: Offering DSA public key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I was under the impression that (as outlined in this question: How to make ssh log in as the right user?) specifying User username in ssh_config should work. Why isn't OpenSSH using the username specified in ssh_config?

    Read the article

  • Is StoreJet Transcend (0x2329) an Advanced Format drive?

    - by Graham Perrin
    I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

    Read the article

  • preformance wise htaccess

    - by purpler
    hese's the my htaccess template, i wonder if anything could be added to increase website performance.. # Defaults AddDefaultCharset UTF-8 DefaultLanguage en-US ServerSignature Off FileETag None Header unset ETag Options -MultiViews #Options All -Indexes # Force the latest IE version or ChromeFrame <IfModule mod_setenvif.c> <IfModule mod_headers.c> BrowserMatch MSIE ie Header set X-UA-Compatible "IE=Edge,chrome=1" env=ie </IfModule> </IfModule> # Proxy X-UA Setup <IfModule mod_headers.c> Header append Vary User-Agent </IfModule> #Rewrites Options +FollowSymlinks RewriteEngine On RewriteBase / # Redirect to non-WWW RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^(.*)$ http://%1/$1 [R=301,L] # Redirect to WWW RewriteCond %{HTTP_HOST} ^domain.com RewriteRule (.*) http://www.domain.com/$1 [R=301,L] # Redirect index to root RewriteRule ^(.*)index\.(php|html)$ /$1 [R=301,L] # Caching ExpiresActive On ExpiresDefault A0 Header set Cache-Control "public" # 1 Year Long Cache <FilesMatch "\.(flv|fla|ico|pdf|avi|mov|ppt|doc|mp3|wmv|wav|png|jpg|jpeg|gif|swf|js|css|ttf|eot|woff|svg|svgz)$"> ExpiresDefault A31622400 </FilesMatch> # Proxy Caching <FilesMatch "\.(css|js|png)$"> ExpiresDefault A31622400 Header set Cache-Control "private" </FilesMatch> # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Proper SVG serving AddType image/svg+xml svg svgz AddEncoding gzip svgz # GZip Compression <IfModule mod_deflate.c> <FilesMatch "\.(php|html|css|js|xml|txt|ttf|otf|eot|svg)$" > SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error page ErrorDocument 404 /404.html # Deny access to sensitive files <FilesMatch "\.(htaccess|ini|log|psd)$"> Order Allow,Deny Deny from all </FilesMatch>

    Read the article

  • Test A SSH Connection from Windows commandline

    - by IguanaMinstrel
    I am looking for a way to test if a SSH server is available from a Windows host. I found this one-liner, but it requires the a Unix/Linux host: ssh -q -o "BatchMode=yes" user@host "echo 2>&1" && echo "UP" || echo "DOWN" Telnet'ing to port 22 works, but that's not really scriptable. I have also played around with Plink, but I haven't found a way to get the functionality of the one-liner above. Does anyone know Plink enough to make this work? Are there any other windows based tools that would work? Please note that the SSH servers in question are behind a corporate firewall and are NOT internet accessible. Arrrg. Figured it out: C:\>plink -batch -v user@host Looking up host "host" Connecting to 10.10.10.10 port 22 We claim version: SSH-2.0-PuTTY_Release_0.62 Server version: SSH-2.0-OpenSSH_4.7p1-hpn12v17_q1.217 Using SSH protocol version 2 Server supports delayed compression; will try this later Doing Diffie-Hellman group exchange Doing Diffie-Hellman key exchange with hash SHA-256 Host key fingerprint is: ssh-rsa 1024 aa:aa:aa:aa:aa:aa:aa:aa:aa:aa:aa:aa:aa:aa:aa:aa Initialised AES-256 SDCTR client->server encryption Initialised HMAC-SHA1 client->server MAC algorithm Initialised AES-256 SDCTR server->client encryption Initialised HMAC-SHA1 server->client MAC algorithm Using username "user". Using SSPI from SECUR32.DLL Attempting GSSAPI authentication GSSAPI authentication initialised GSSAPI authentication initialised GSSAPI authentication loop finished OK Attempting keyboard-interactive authentication Disconnected: Unable to authenticate C:\>

    Read the article

  • Warning: Cannot modify header information - headers already sent

    - by Pankaj Khurana
    Hi, I am using code available on http://www.forosdelweb.com/f18/zip-lib-php-archivo-zip-vacio-431133/ for creating zip file. First file-zip.lib.php <?php /* $Id: zip.lib.php,v 1.1 2004/02/14 15:21:18 anoncvs_tusedb Exp $ */ // vim: expandtab sw=4 ts=4 sts=4: /** * Zip file creation class. * Makes zip files. * * Last Modification and Extension By : * * Hasin Hayder * HomePage : www.hasinme.info * Email : [email protected] * IDE : PHP Designer 2005 * * * Originally Based on : * * http://www.zend.com/codex.php?id=535&single=1 * By Eric Mueller <[email protected]> * * http://www.zend.com/codex.php?id=470&single=1 * by Denis125 <[email protected]> * * a patch from Peter Listiak <[email protected]> for last modified * date and time of the compressed file * * Official ZIP file format: http://www.pkware.com/appnote.txt * * @access public */ class zipfile { /** * Array to store compressed data * * @var array $datasec */ var $datasec = array(); /** * Central directory * * @var array $ctrl_dir */ var $ctrl_dir = array(); /** * End of central directory record * * @var string $eof_ctrl_dir */ var $eof_ctrl_dir = "\x50\x4b\x05\x06\x00\x00\x00\x00"; /** * Last offset position * * @var integer $old_offset */ var $old_offset = 0; /** * Converts an Unix timestamp to a four byte DOS date and time format (date * in high two bytes, time in low two bytes allowing magnitude comparison). * * @param integer the current Unix timestamp * * @return integer the current date in a four byte DOS format * * @access private */ function unix2DosTime($unixtime = 0) { $timearray = ($unixtime == 0) ? getdate() : getdate($unixtime); if ($timearray['year'] < 1980) { $timearray['year'] = 1980; $timearray['mon'] = 1; $timearray['mday'] = 1; $timearray['hours'] = 0; $timearray['minutes'] = 0; $timearray['seconds'] = 0; } // end if return (($timearray['year'] - 1980) << 25) | ($timearray['mon'] << 21) | ($timearray['mday'] << 16) | ($timearray['hours'] << 11) | ($timearray['minutes'] << 5) | ($timearray['seconds'] >> 1); } // end of the 'unix2DosTime()' method /** * Adds "file" to archive * * @param string file contents * @param string name of the file in the archive (may contains the path) * @param integer the current timestamp * * @access public */ function addFile($data, $name, $time = 0) { $name = str_replace('', '/', $name); $dtime = dechex($this->unix2DosTime($time)); $hexdtime = 'x' . $dtime[6] . $dtime[7] . 'x' . $dtime[4] . $dtime[5] . 'x' . $dtime[2] . $dtime[3] . 'x' . $dtime[0] . $dtime[1]; eval('$hexdtime = "' . $hexdtime . '";'); $fr = "\x50\x4b\x03\x04"; $fr .= "\x14\x00"; // ver needed to extract $fr .= "\x00\x00"; // gen purpose bit flag $fr .= "\x08\x00"; // compression method $fr .= $hexdtime; // last mod time and date // "local file header" segment $unc_len = strlen($data); $crc = crc32($data); $zdata = gzcompress($data); $zdata = substr(substr($zdata, 0, strlen($zdata) - 4), 2); // fix crc bug $c_len = strlen($zdata); $fr .= pack('V', $crc); // crc32 $fr .= pack('V', $c_len); // compressed filesize $fr .= pack('V', $unc_len); // uncompressed filesize $fr .= pack('v', strlen($name)); // length of filename $fr .= pack('v', 0); // extra field length $fr .= $name; // "file data" segment $fr .= $zdata; // "data descriptor" segment (optional but necessary if archive is not // served as file) $fr .= pack('V', $crc); // crc32 $fr .= pack('V', $c_len); // compressed filesize $fr .= pack('V', $unc_len); // uncompressed filesize // add this entry to array $this -> datasec[] = $fr; // now add to central directory record $cdrec = "\x50\x4b\x01\x02"; $cdrec .= "\x00\x00"; // version made by $cdrec .= "\x14\x00"; // version needed to extract $cdrec .= "\x00\x00"; // gen purpose bit flag $cdrec .= "\x08\x00"; // compression method $cdrec .= $hexdtime; // last mod time & date $cdrec .= pack('V', $crc); // crc32 $cdrec .= pack('V', $c_len); // compressed filesize $cdrec .= pack('V', $unc_len); // uncompressed filesize $cdrec .= pack('v', strlen($name) ); // length of filename $cdrec .= pack('v', 0 ); // extra field length $cdrec .= pack('v', 0 ); // file comment length $cdrec .= pack('v', 0 ); // disk number start $cdrec .= pack('v', 0 ); // internal file attributes $cdrec .= pack('V', 32 ); // external file attributes - 'archive' bit set $cdrec .= pack('V', $this -> old_offset ); // relative offset of local header $this -> old_offset += strlen($fr); $cdrec .= $name; // optional extra field, file comment goes here // save to central directory $this -> ctrl_dir[] = $cdrec; } // end of the 'addFile()' method /** * Dumps out file * * @return string the zipped file * * @access public */ function file() { $data = implode('', $this -> datasec); $ctrldir = implode('', $this -> ctrl_dir); return $data . $ctrldir . $this -> eof_ctrl_dir . pack('v', sizeof($this -> ctrl_dir)) . // total # of entries "on this disk" pack('v', sizeof($this -> ctrl_dir)) . // total # of entries overall pack('V', strlen($ctrldir)) . // size of central dir pack('V', strlen($data)) . // offset to start of central dir "\x00\x00"; // .zip file comment length } // end of the 'file()' method /** * A Wrapper of original addFile Function * * Created By Hasin Hayder at 29th Jan, 1:29 AM * * @param array An Array of files with relative/absolute path to be added in Zip File * * @access public */ function addFiles($files /*Only Pass Array*/) { foreach($files as $file) { if (is_file($file)) //directory check { $data = implode("",file($file)); $this->addFile($data,$file); } } } /** * A Wrapper of original file Function * * Created By Hasin Hayder at 29th Jan, 1:29 AM * * @param string Output file name * * @access public */ function output($file) { $fp=fopen($file,"w"); fwrite($fp,$this->file()); fclose($fp); } } // end of the 'zipfile' class ?> My second file newzip.php <? include("zip.lib.php"); $ziper = new zipfile(); $ziper->addFiles(array("index.htm")); //array of files // the next three lines force an immediate download of the zip file: header("Content-type: application/octet-stream"); header("Content-disposition: attachment; filename=test.zip"); echo $ziper -> file(); ?> I am getting this warning while executing newzip.php Warning: Cannot modify header information - headers already sent by (output started at E:\xampp\htdocs\demo\zip.lib.php:233) in E:\xampp\htdocs\demo\newzip.php on line 6 I am unable to figure out the reason for the same. Please help me on this. Thanks

    Read the article

  • gitolite mac don't add new user to authorized_keys

    - by crashbus
    I installed gitolite and every thing works fine for me as admin. But when I'd like to add add a new user the new user can't connect to the server. After I looked into the file authorized_keys I saw that the new user wasn't added to the file. During the commit of the new public-key I get some workings: WARNING: split conf not set, gl-conf present for 'gitolite-admin' Counting objects: 6, done. Delta compression using up to 8 threads. Compressing objects: 100% (4/4), done. Writing objects: 100% (4/4), 882 bytes, done. Total 4 (delta 1), reused 0 (delta 0) remote: WARNING: split conf not set, gl-conf present for 'gitolite-admin' remote: WARNING: ?? @staff christianwaldmann markwelch remote: sh: find: command not found remote: sh: find: command not found remote: sh: sort: command not found remote: sh: find: command not found remote: /usr/local/bin/triggers/post-compile/update-gitweb-access-list: line 26: cut: command not found remote: /usr/local/bin/triggers/post-compile/update-gitweb-access-list: line 23: grep: command not found remote: /usr/local/bin/triggers/post-compile/update-gitweb-access-list: line 26: sort: command not found remote: /usr/local/bin/triggers/post-compile/update-gitweb-access-list: line 26: sed: command not found remote: sh: find: command not found remote: sh: find: command not found How can I fix it that gitolite auto-add the new user to the authorized_keys.

    Read the article

  • Free software for backing up an attached network drive

    - by Richard
    My wireless router comes with a USB connector which allows me to plug an external hard drive in and it'll act as a Network Attached Storage. The problem is that I want to backup this hard-drive to the external drive of another computer so that if the NAS drive fails, I don't lose everything. However, Windows 7 Backup refuses to include the NAS as a location to backup. I can't fool it by mapping it to a drive letter either. Google presents lots of pages on how to backup files to a NAS, but not the other way around. Can anyone advise me on free software which can do incremental backups of a NAS drive to an external drive attached the computer it is running on? I'm aware of this question but the top answers have one or more of the following issues: They aren't free. The free version cannot backup a NAS. They cannot do incremental backups. They're just a script and therefore have limited other functionality (eg. disk space management, scheduling, compression, etc.etc.)

    Read the article

  • Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

    - by WerkkreW
    Hello - I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified with SpeakEasy and Speedtest.net) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

    Read the article

  • rsnapshot - not correctly archiving mysql databases

    - by Tiffany Walker
    My rsnapshot configuration: snapshot_root /.snapshots/ backup /home/user localhost/ backup_script /usr/local/backup_mysql.sh localhost/mysql/ Using this file: NOW=$(date +"%m-%d-%Y") # mm-dd-yyyy format FILE="" # used in a loop ### Server Setup ### #* MySQL login user name *# MUSER="root" #* MySQL login PASSWORD name *# MPASS="YOUR-PASSWORD" #* MySQL login HOST name *# MHOST="127.0.0.1" #* MySQL binaries *# MYSQL="$(which mysql)" MYSQLDUMP="$(which mysqldump)" GZIP="$(which gzip)" # get all database listing DBS="$($MYSQL -u $MUSER -h $MHOST -p$MPASS -Bse 'show databases')" # start to dump database one by one for db in $DBS do FILE=$BAK/mysql-$db.$NOW-$(date +"%T").gz # gzip compression for each backup file $MYSQLDUMP --single-transaction -u $MUSER -h $MHOST -p$MPASS $db | $GZIP -9 > $FILE done It dumps the databases under / I then tried with the following: http://bash.cyberciti.biz/backup/rsnapshot-remote-mysql-backup-shell-script/ I got: rsnapshot hourly ---------------------------------------------------------------------------- rsnapshot encountered an error! The program was invoked with these options: /usr/bin/rsnapshot hourly ---------------------------------------------------------------------------- ERROR: backup_script /usr/local/backup_mysql.sh returned 1 WARNING: Rolling back "localhost/mysql/" ls -la /.snapshots/hourly.0/localhost/mysql total 8 drwxr-xr-x 2 root root 4096 Nov 23 17:43 ./ drwxr-xr-x 4 root root 4096 Nov 23 18:20 ../ What exactly am I doing wrong? EDIT: # /usr/local/backup_mysql.sh *** Dumping MySQL Database *** Database> information_schema..cphulkd..eximstats..horde..leechprotect..logaholicDB_ns1..modsec..mysql..performance_schema..roundcube..test.. *** Backup done [ files wrote to /.snapshots/tmp/mysql] *** root@ns1 [~]# ls -la /.snapshots/tmp/mysql total 8040 drwxr-xr-x 2 root root 4096 Nov 23 18:41 ./ drwxr-xr-x 3 root root 4096 Nov 23 18:41 ../ -rw-r--r-- 1 root root 1409 Nov 23 18:41 cphulkd.18_41_45pm.gz -rw-r--r-- 1 root root 113522 Nov 23 18:41 eximstats.18_41_45pm.gz -rw-r--r-- 1 root root 4583 Nov 23 18:41 horde.18_41_45pm.gz -rw-r--r-- 1 root root 71757 Nov 23 18:41 information_schema.18_41_45pm.gz -rw-r--r-- 1 root root 692 Nov 23 18:41 leechprotect.18_41_45pm.gz -rw-r--r-- 1 root root 2603 Nov 23 18:41 logaholicDB_ns1.18_41_45pm.gz -rw-r--r-- 1 root root 745 Nov 23 18:41 modsec.18_41_45pm.gz -rw-r--r-- 1 root root 138928 Nov 23 18:41 mysql.18_41_45pm.gz -rw-r--r-- 1 root root 1831 Nov 23 18:41 performance_schema.18_41_45pm.gz -rw-r--r-- 1 root root 3610 Nov 23 18:41 roundcube.18_41_45pm.gz -rw-r--r-- 1 root root 436 Nov 23 18:41 test.18_41_47pm.gz MySQL Backup seems fine.

    Read the article

  • How to move your Windows User Profile to another drive in Windows 8

    - by Mark
    I like to have my user folder on a different drive (D:) than my OS is (C:). Reading the following post I decided to give it a try. All went quite well, untill I found out that my Windows 8 Apps won't execute anymore (other than that I didn't noticed any problems). My apps do work, while using an account that isn't moved. In the eventviewer I've found error messages like these: App <Microsoft.MicrosoftSkyDrive> crashed with an unhandled Javascript exception. App details are as follows: Display Name:<SkyDrive>, AppUserModelId: <microsoft.microsoftskydrive_8wekyb3d8bbwe!Microsoft.MicrosoftSkyDrive> Package Identity:<microsoft.microsoftskydrive_16.4.4204.712_x64__8wekyb3d8bbwe> PID:<4452>. The details of the JavaScript exception are as follows Exception Name:<WinRT error>, Description:<Loading the state store failed. > , HTML Document Path:</modernskydrive/product/skydrive/App.html>, Source File Name:<ms-appx://microsoft.microsoftskydrive/jx/jx.js>, Source Line Number:<1>, Source Column Number:<27246>, and Stack Trace: ms-appx://microsoft.microsoftskydrive/jx/jx.js:1:27246 localSettings() ms-appx://microsoft.microsoftskydrive/jx/jx.js:1:51544 _initSettings() ms-appx://microsoft.microsoftskydrive/jx/jx.js:1:54710 getApplicationStatus(boolean) ms-appx://microsoft.microsoftskydrive/jx/jx.js:1:48180 init(object) ms-appx://microsoft.microsoftskydrive/jx/jx.js:1:45583 Application(number, boolean) ms-appx://microsoft.microsoftskydrive/modernskydrive/product/skydrive/App.html:216:13 Anonymous function(object) Using ProcMon, I see a lot of access denied messages, like these: Date & Time: 12-9-2012 9:32:20 Event Class: File System Operation: CreateFile Result: ACCESS DENIED Path: D:\Users\John\AppData\Local\Packages\microsoft.microsoftskydrive_8wekyb3d8bbwe\Settings\settings.dat TID: 2520 Duration: 0.0000149 Desired Access: Read Data/List Directory, Write Data/Add File, Read Control Disposition: OpenIf Options: Sequential Access, Synchronous IO Non-Alert, No Compression Attributes: N ShareMode: None AllocationSize: 0 Any idea how to solve this? I noticed that the app folders e.g.: D:\Users\john\AppData\Local\Packages\microsoft.microsoftskydrive_8wekyb3d8bbwe had a different owner than the old profile folder had. Old profile folder had john as owner where my new profile folder had the Administrators group as owner. Changing this didn't help unfortunately.

    Read the article

  • Codec Problems with trying to edit videos with VirtualDub

    - by Roy Rico
    So, I'm a little frustrated. According to this post and various other internet sources, virtualdub is supposed to allow users to quickly split and join video files. I am using windows 7 64 Bit and the latest version of VirtualDub (64-bit). I have tried to edit various movie files, and each attempt at editing various files I have done has not worked for me. AVI file A.avi won't load, saying that it can't located the Decompressor for the "FMP4" format. I have tried this solution and this one, and neither of them work. I have tried setting the VFW Decompressor for 'Other MPEG4' setting to XVID or LIBAVCODEC. There is no change in Virtual Dub. AVI file C.avi will load in Virtual Dub, but any attempt to split it gives me an error that I don't have XVID codecs installed. I've attempted to install the proper codecs (Shark's Windows 7 Codecs, CCCP) with no change. AVI file C.avi will load, and it will split, but won't split using the "Direct Stream Copy" claiming the compression algorithm is incompatible. I tried the "Fast Recompress" option and it created a 27GB file out of what was supposed to be about a 300-400MB file. Can someone please give me some insight into what I'm messing up?

    Read the article

  • Is there a tool that can test what SSL/TLS cipher suites a particular website offers?

    - by Jeremy Powell
    Is there a tool that can test what SSL/TLS cipher suites a particular website offers? I've tried openssl, but if you examine the output: $ echo -n | openssl s_client -connect www.google.com:443 CONNECTED(00000003) depth=1 /C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA verify error:num=20:unable to get local issuer certificate verify return:0 --- Certificate chain 0 s:/C=US/ST=California/L=Mountain View/O=Google Inc/CN=www.google.com i:/C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA 1 s:/C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA i:/C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority --- Server certificate -----BEGIN CERTIFICATE----- MIIDITCCAoqgAwIBAgIQL9+89q6RUm0PmqPfQDQ+mjANBgkqhkiG9w0BAQUFADBM MQswCQYDVQQGEwJaQTElMCMGA1UEChMcVGhhd3RlIENvbnN1bHRpbmcgKFB0eSkg THRkLjEWMBQGA1UEAxMNVGhhd3RlIFNHQyBDQTAeFw0wOTEyMTgwMDAwMDBaFw0x MTEyMTgyMzU5NTlaMGgxCzAJBgNVBAYTAlVTMRMwEQYDVQQIEwpDYWxpZm9ybmlh MRYwFAYDVQQHFA1Nb3VudGFpbiBWaWV3MRMwEQYDVQQKFApHb29nbGUgSW5jMRcw FQYDVQQDFA53d3cuZ29vZ2xlLmNvbTCBnzANBgkqhkiG9w0BAQEFAAOBjQAwgYkC gYEA6PmGD5D6htffvXImttdEAoN4c9kCKO+IRTn7EOh8rqk41XXGOOsKFQebg+jN gtXj9xVoRaELGYW84u+E593y17iYwqG7tcFR39SDAqc9BkJb4SLD3muFXxzW2k6L 05vuuWciKh0R73mkszeK9P4Y/bz5RiNQl/Os/CRGK1w7t0UCAwEAAaOB5zCB5DAM BgNVHRMBAf8EAjAAMDYGA1UdHwQvMC0wK6ApoCeGJWh0dHA6Ly9jcmwudGhhd3Rl LmNvbS9UaGF3dGVTR0NDQS5jcmwwKAYDVR0lBCEwHwYIKwYBBQUHAwEGCCsGAQUF BwMCBglghkgBhvhCBAEwcgYIKwYBBQUHAQEEZjBkMCIGCCsGAQUFBzABhhZodHRw Oi8vb2NzcC50aGF3dGUuY29tMD4GCCsGAQUFBzAChjJodHRwOi8vd3d3LnRoYXd0 ZS5jb20vcmVwb3NpdG9yeS9UaGF3dGVfU0dDX0NBLmNydDANBgkqhkiG9w0BAQUF AAOBgQCfQ89bxFApsb/isJr/aiEdLRLDLE5a+RLizrmCUi3nHX4adpaQedEkUjh5 u2ONgJd8IyAPkU0Wueru9G2Jysa9zCRo1kNbzipYvzwY4OA8Ys+WAi0oR1A04Se6 z5nRUP8pJcA2NhUzUnC+MY+f6H/nEQyNv4SgQhqAibAxWEEHXw== -----END CERTIFICATE----- subject=/C=US/ST=California/L=Mountain View/O=Google Inc/CN=www.google.com issuer=/C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA --- No client certificate CA names sent --- SSL handshake has read 1777 bytes and written 316 bytes --- New, TLSv1/SSLv3, Cipher is AES256-SHA Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : AES256-SHA Session-ID: 748E2B5FEFF9EA065DA2F04A06FBF456502F3E64DF1B4FF054F54817C473270C Session-ID-ctx: Master-Key: C4284AE7D76421F782A822B3780FA9677A726A25E1258160CA30D346D65C5F4049DA3D10A41F3FA4816DD9606197FAE5 Key-Arg : None Start Time: 1266259321 Timeout : 300 (sec) Verify return code: 20 (unable to get local issuer certificate) --- it just shows that the cipher suite is something with AES256-SHA. I know I could grep through the hex dump of the conversation, but I was hoping for something a little more elegant. I would prefer Linux tools, but Windows (or other) would be fine. This question is motivated by the security testing I do for PCI and general penetration testing. Update: GregS points out below that the SSL server picks from the cipher suites of the client. So it seems I would need to test all cipher suites one at a time. I think I can hack something together, but is there a tool that does particularly this?

    Read the article

  • Network connection keeps dropping - bad hardware?

    - by Bill Sambrone
    Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

    Read the article

  • Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

    - by WerkkreW
    I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

    Read the article

  • JBoss https on port other than 8080 not working

    - by MilindaD
    We have a server with two JBoss instances where one runs on 8080, the other on 8081. We need to have HTTPS enabled for the 8081 server, firstly we tried enabling https on the 8080 port instance by generating the keystore and editing the server.xml and it successfully worked. However when we tried the same thing for 8081 it did not, note that we removed https for the 8080 server first before enabling it for 8081. This is what was used for both server.xml for 8080 and 8081. The only difference was that the port was changed from 8080 to 8081 when trying to enable https for 8081 port instance. What am I doing wrong and what needs to be changed? NOTE : When I meant enabled for 8080 I meant when you visit https:// URL:8484 you will actually be visiting the 8080 port instance. However when ssl is enabled for 8081 and I visit https:// URL:8484 I get that the web page is unavailable. COMMENTLESS VERSION <Server> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <Listener className="org.apache.catalina.core.JasperListener" /> <Service name="jboss.web"> <!-- https --> <Connector port="8080" address="${jboss.bind.address}" maxThreads="350" maxHttpHeaderSize="8192" emptySessionPath="true" protocol="HTTP/1.1" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" compression="on" ompressableMimeType="text/html,text/css,text/javascript,application/json,text/xml,text/plain,application/x-javascript,application/javascript"/> <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" address="${jboss.bind.address}" keystoreFile="${jboss.server.home.dir}/conf/supun1.keystore" keystorePass="aaaaaa" truststoreFile="${jboss.server.home.dir}/conf/supun1.keystore" truststorePass="aaaaaa" /> <!-- https1 --> <Connector port="8009" address="${jboss.bind.address}" protocol="AJP/1.3" emptySessionPath="true" enableLookups="false" redirectPort="8443" /> <Engine name="jboss.web" defaultHost="localhost" jvmRoute="khms1"> <Realm className="org.jboss.web.tomcat.security.JBossSecurityMgrRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> <Host name="localhost" autoDeploy="false" deployOnStartup="false" deployXML="false" configClass="org.jboss.web.tomcat.security.config.JBossContextConfig" > <Valve className="org.jboss.web.tomcat.service.sso.ClusteredSingleSignOn" /> <Valve className="org.jboss.web.tomcat.service.jca.CachedConnectionValve" cachedConnectionManagerObjectName="jboss.jca:service=CachedConnectionManager" transactionManagerObjectName="jboss:service=TransactionManager" /> </Host> </Engine> </Service> </Server> WITH COMMENTS VERSION <Server> <!--APR library loader. Documentation at /docs/apr.html --> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <!--Initialize Jasper prior to webapps are loaded. Documentation at /docs/jasper-howto.html --> <Listener className="org.apache.catalina.core.JasperListener" /> <!-- Use a custom version of StandardService that allows the connectors to be started independent of the normal lifecycle start to allow web apps to be deployed before starting the connectors. --> <Service name="jboss.web"> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8080" address="${jboss.bind.address}" maxThreads="350" maxHttpHeaderSize="8192" emptySessionPath="true" protocol="HTTP/1.1" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" compression="on" ompressableMimeType="text/html,text/css,text/javascript,application/json,text/xml,text/plain,application/x-javascript,application/javascript"/> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" keystoreFile="${jboss.server.home.dir}/conf/zara.keystore" keystorePass="zara2010" clientAuth="false" sslProtocol="TLS" compression="on" /> --> <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" address="${jboss.bind.address}" keystoreFile="${jboss.server.home.dir}/conf/supun1.keystore" keystorePass="aaaaaa" truststoreFile="${jboss.server.home.dir}/conf/supun1.keystore" truststorePass="aaaaaa" /> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" address="${jboss.bind.address}" protocol="AJP/1.3" emptySessionPath="true" enableLookups="false" redirectPort="8443" /> <Engine name="jboss.web" defaultHost="localhost" jvmRoute="khms1"> <!-- The JAAS based authentication and authorization realm implementation that is compatible with the jboss 3.2.x realm implementation. - certificatePrincipal : the class name of the org.jboss.security.auth.certs.CertificatePrincipal impl used for mapping X509[] cert chains to a Princpal. - allRolesMode : how to handle an auth-constraint with a role-name=*, one of strict, authOnly, strictAuthOnly + strict = Use the strict servlet spec interpretation which requires that the user have one of the web-app/security-role/role-name + authOnly = Allow any authenticated user + strictAuthOnly = Allow any authenticated user only if there are no web-app/security-roles --> <Realm className="org.jboss.web.tomcat.security.JBossSecurityMgrRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> <!-- A subclass of JBossSecurityMgrRealm that uses the authentication behavior of JBossSecurityMgrRealm, but overrides the authorization checks to use JACC permissions with the current java.security.Policy to determine authorized access. - allRolesMode : how to handle an auth-constraint with a role-name=*, one of strict, authOnly, strictAuthOnly + strict = Use the strict servlet spec interpretation which requires that the user have one of the web-app/security-role/role-name + authOnly = Allow any authenticated user + strictAuthOnly = Allow any authenticated user only if there are no web-app/security-roles <Realm className="org.jboss.web.tomcat.security.JaccAuthorizationRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> --> <Host name="localhost" autoDeploy="false" deployOnStartup="false" deployXML="false" configClass="org.jboss.web.tomcat.security.config.JBossContextConfig" > <!-- Uncomment to enable request dumper. This Valve "logs interesting contents from the specified Request (before processing) and the corresponding Response (after processing). It is especially useful in debugging problems related to headers and cookies." --> <!-- <Valve className="org.apache.catalina.valves.RequestDumperValve" /> --> <!-- Access logger --> <!-- <Valve className="org.apache.catalina.valves.AccessLogValve" prefix="localhost_access_log." suffix=".log" pattern="common" directory="${jboss.server.log.dir}" resolveHosts="false" /> --> <!-- Uncomment to enable single sign-on across web apps deployed to this host. Does not provide SSO across a cluster. If this valve is used, do not use the JBoss ClusteredSingleSignOn valve shown below. A new configuration attribute is available beginning with release 4.0.4: cookieDomain configures the domain to which the SSO cookie will be scoped (i.e. the set of hosts to which the cookie will be presented). By default the cookie is scoped to "/", meaning the host that presented it. Set cookieDomain to a wider domain (e.g. "xyz.com") to allow an SSO to span more than one hostname. --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Uncomment to enable single sign-on across web apps deployed to this host AND to all other hosts in the cluster. If this valve is used, do not use the standard Tomcat SingleSignOn valve shown above. Valve uses a JBossCache instance to support SSO credential caching and replication across the cluster. The JBossCache instance must be configured separately. By default, the valve shares a JBossCache with the service that supports HttpSession replication. See the "jboss-web-cluster-service.xml" file in the server/all/deploy directory for cache configuration details. Besides the attributes supported by the standard Tomcat SingleSignOn valve (see the Tomcat docs), this version also supports the following attributes: cookieDomain see above treeCacheName JMX ObjectName of the JBossCache MBean used to support credential caching and replication across the cluster. If not set, the default value is "jboss.cache:service=TomcatClusteringCache", the standard ObjectName of the JBossCache MBean used to support session replication. --> <Valve className="org.jboss.web.tomcat.service.sso.ClusteredSingleSignOn" /> <!-- Check for unclosed connections and transaction terminated checks in servlets/jsps. Important: The dependency on the CachedConnectionManager in META-INF/jboss-service.xml must be uncommented, too --> <Valve className="org.jboss.web.tomcat.service.jca.CachedConnectionValve" cachedConnectionManagerObjectName="jboss.jca:service=CachedConnectionManager" transactionManagerObjectName="jboss:service=TransactionManager" /> </Host> </Engine> </Service> </Server>

    Read the article

  • How to install/configure ffmpeg to compress mp4 videos for flash player delivery?

    - by Andrew Fulton
    We have a flash web-app that created interactive video, and are using ffmpeg to do some compression/resizing when a user "publishes" their project. The user can upload flv files and mp4 files, both of which play fine in the Flash UI before publishing. After publishing the flv files work fine, but the mp4 files will not play in the flash player: Audio will play but video won't. The mp4 files will play fine if I download them and play them in the Quicktime player but if I attempt to open them in the Adobe Media Player it reports "The media file does not contain a supported video track". If I open the Movie inspector in quicktime it tells me that the original file is an "h264" video and the ffmpeg-processed ones are "mpeg-4". I have tried forcing it to h264 by adding flags like -f h264 and -vcodec h264 but I get a screenfull of errors (no frame, illegal POC type, sps_id out of range) ending with Could not find codec parameters (Video: h264) h264 will show up if I run ffmpeg -formats and ffmpeg -codecs, and as I said it will play fine in Quicktime. Is there anything else I need to do to convince the flash player to play them? Is there anything else I need to tell you about the server that will help?

    Read the article

  • Caching all files in varnish

    - by csgwro
    I want my varnish servers to cache all files. At backend there is lighttpd hosting only static files, and there is an md5 in the url in case of file change, ex. /gfx/Bird.b6e0bc2d6cbb7dfe1a52bc45dd2b05c4.swf). However my hit ratio is very poorly (about 0.18) My config: sub vcl_recv { set req.backend=default; ### passing health to backend if (req.url ~ "^/health.html$") { return (pass); } remove req.http.If-None-Match; remove req.http.cookie; remove req.http.authenticate; if (req.request == "GET") { return (lookup); } } sub vcl_fetch { ### do not cache wrong codes if (beresp.status == 404 || beresp.status >= 500) { set beresp.ttl = 0s; } remove beresp.http.Etag; remove beresp.http.Last-Modified; } sub vcl_deliver { set resp.http.expires = "Thu, 31 Dec 2037 23:55:55 GMT"; } I have made an performance tuning: DAEMON_OPTS="${DAEMON_OPTS} -p thread_pool_min=200 -p thread_pool_max=4000 -p thread_pool_add_delay=2 -p session_linger=100" The main url which is missed is... /health.html. Is that forward to backend correctly configured? Disabling health checking hit ratio increases to 0.45. Now mostly "/crossdomain.xml" is missed (from many domains, as it is wildcard). How can I avoid that? Should I carry on other headers like User-Agent or Accept-Encoding? I thing that default hashing mechanism is using url + host/IP. Compression is used at the backend. What else can improve performance?

    Read the article

  • GitHub - commit local changes in local branch to remote branch

    - by user62046
    I use Git Shell in Windows 7, working in a branch named Save-Rotation. Then I used git push origin Save-Rotation to commit the changes to remote. The result is posted at the end. It seems good. But when I went to my repository in GitHub site, which is https://github.com/chiapas/sumatrapdf/tree/Save-Rotation I can't see any change in the repository tree or commit tree. How can I know if the commit (to remote) is successful, and why the repository page is not updated? Here is the result in command-line C:\Users\imo\Documents\GitHub\sumatrapdf [Save-Rotation]> git push origin Save-R otation Counting objects: 167, done. Delta compression using up to 8 threads. Compressing objects: 100% (18/18), done. Writing objects: 100% (119/119), 27.43 KiB, done. Total 119 (delta 101), reused 119 (delta 101) To https://github.com/chiapas/sumatrapdf * [new branch] Save-Rotation -> Save-Rotation C:\Users\imo\Documents\GitHub\sumatrapdf [Save-Rotation +2 ~17 -0 !]> git push o rigin Save-Rotation Everything up-to-date C:\Users\imo\Documents\GitHub\sumatrapdf [Save-Rotation +2 ~17 -0 !]>

    Read the article

  • IIS 7 much slower than IIS 6

    - by JoeJoe
    I have a asp.net 3.5 web application running fine on Windows2003 IIS6. I published same exact application to IIS7.5 (Win2008R2) on a faster box (i5,8Gram) and it is significantly slower. 5-6 sec per page vs. 1-2 sec per page. During that time the Task Mgr CPU is always under 10%. Both attach to same database on other box. Benchmark is consistent from any other client browser or machine. I have connection pool on both, compression on both. Same network subnet. Forms authentication (no SSL yet). Can you give me steps on how to troubleshoot where the delays are being inserted or settings in IIS7 that I may have overlooked. Just using defaults. There is only 1 web site on each box. I understand the roles of an Application as defined in IIS has changed. There is no special Application defined in IIS.

    Read the article

  • Why doesn't SSHFS let me look into a mounted directory?

    - by Jan
    I use SSHFS to mount a directory on a remote server. There is a user xxx on client and server. UID and GID are identical on both boxes. I use sshfs -o kernel_cache -o auto_cache -o reconnect -o compression=no \ -o cache_timeout=600 -o ServerAliveInterval=15 \ [email protected]:/mnt/content /home/xxx/path_to/content to mount the directory on the remote server. When I log in as xxx on the client I have no problems. I can cd into /home/xxx/path_to/content. But when I log in on the client as another user zzz and then $ ls -l /home/xxx/path_to I get this d????????? ? ? ? ? ? content and on $ ls -l /home/xxx/path_to/content I get ls: cannot access content: Permission denied When I do $ ls -l /mnt on the remote server I get drwxr-xr-x 6 xxx xxx 4096 2011-07-25 12:51 content What am I doing wrong? The permissions seem to be correct to me. Am I wrong?

    Read the article

  • Redirecting or routing all traffic to OpenVPN on a Mac OS X client

    - by sdr56p
    I have configured an OpenVPN (2.2.1) server on an Ubuntu virtual machine in the Amazon elastic compute cloud. The server is up and running. I have installed OpenVPN (2.2.1) on a Mac OS X (10.8.2) client and I am using the openvpn2 binary to connect (in opposition to other clients like Tunnelblick or Viscosity). I can connect with the client and successfully ping or ssh the server through the tunnel. However, I can't redirect all internet traffic through the VPN even if I use the push "redirect-gateway def1 bypass-dhcp" option in the server.conf configurations. When I connect to the server with these configurations, I get a successful connection, but then an infinite series of error messages: "write UDPv4: No route to host (code=65)". Traffic routing seems to be compromised because I am not able to access anything anymore, not even the OpenVPN server (by pinging 10.8.0.1 for instance). This is beyond me. I am finding little help on the web and don't know what to try next. I don't think it is a problem of forwarding the traffic on the server since, first, I have also took care of that and, second, I can't even ping the VPN server locally through the tunnel (or ping anything at all for that matter). Thank you for your help. Here is the server.conf. file: port 1194 proto udp dev tun ca ca.crt cert ec2-server.crt key ec2-server.key # This file should be kept secret dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 And the client.conf file: client dev tun proto udp remote servername.com 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert Toto5.crt key Toto5.key ns-cert-type server comp-lzo verb 3 Here is the connection log with the error messages: $ sudo openvpn2 --config client.conf Wed Mar 13 22:58:22 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:22 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:22 2013 LZO compression initialized Wed Mar 13 22:58:22 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:22 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:22 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:22 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:22 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:22 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:22 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:22 2013 TLS: Initial packet from 54.234.43.171:1194, sid=ffbaf343 d0c1a266 Wed Mar 13 22:58:22 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:22 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:22 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:23 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:58:25 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:58:25 2013 PUSH: Received control message: 'PUSH_REPLY,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:58:25 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:58:25 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:58:25 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:58:25 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:25 2013 Initialization Sequence Completed ^CWed Mar 13 22:58:30 2013 event_wait : Interrupted system call (code=4) Wed Mar 13 22:58:30 2013 TCP/UDP: Closing socket Wed Mar 13 22:58:30 2013 /sbin/route delete -net 10.8.0.0 10.8.0.5 255.255.255.0 delete net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:30 2013 Closing TUN/TAP interface Wed Mar 13 22:58:30 2013 SIGINT[hard,] received, process exiting toto5:ttntec2 Dominic$ sudo openvpn2 --config client.conf --remote ec2-54-234-43-171.compute-1.amazonaws.com Wed Mar 13 22:58:57 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:57 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:57 2013 LZO compression initialized Wed Mar 13 22:58:57 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:57 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:57 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:57 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:57 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:57 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:57 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:57 2013 TLS: Initial packet from 54.234.43.171:1194, sid=a0d75468 ec26de14 Wed Mar 13 22:58:58 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:58 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:58 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:59:00 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:59:00 2013 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:59:00 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:59:00 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:59:00 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:59:00 2013 /sbin/route add -net 54.234.43.171 0.0.0.0 255.255.255.255 add net 54.234.43.171: gateway 0.0.0.0 Wed Mar 13 22:59:00 2013 /sbin/route add -net 0.0.0.0 10.8.0.5 128.0.0.0 add net 0.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 128.0.0.0 10.8.0.5 128.0.0.0 add net 128.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 Initialization Sequence Completed Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) ... The routing table after a connection WITHOUT the push redirect-gateway (all traffic is not redirected to the VPN and everything is working fine, I can ping or ssh the OpenVPN server and access all other Internet resources through my default gateway): Destination Gateway Flags Refs Use Netif Expire default user148-1.wireless UGSc 50 0 en1 10.8/24 10.8.0.5 UGSc 2 7 tun0 10.8.0.5 10.8.0.6 UH 3 2 tun0 127 localhost UCS 0 0 lo0 localhost localhost UH 6 6692 lo0 client.openvpn.net client.openvpn.net UH 3 18 lo0 142.1.148/22 link#5 UCS 2 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 50 0 en1 76 user150-173.wirele localhost UHS 0 0 lo0 142.1.151.255 ff:ff:ff:ff:ff:ff UHLWbI 0 2 en1 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSWi 0 0 en1 71 The routing table after a connection with the push redirect-gateway option enable as in the server.conf file above (all internet traffic should be redirected to the VPN tunnel, but nothing is working, I can't access any Internet ressources at all): Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 1 0 tun0 default user148-1.wireless UGSc 7 0 en1 10.8/24 10.8.0.5 UGSc 0 0 tun0 10.8.0.5 10.8.0.6 UHr 6 0 tun0 54.234.43.171/32 0.0.0.0 UGSc 1 0 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 3 6698 lo0 client.openvpn.net client.openvpn.net UH 0 27 lo0 128.0/1 10.8.0.5 UGSc 2 0 tun0 142.1.148/22 link#5 UCS 1 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 1 0 en1 833 user150-173.wirele localhost UHS 0 0 lo0 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSW 0 0 en1

    Read the article

  • file system that allow to specify different RAID level per directory and change it afterward

    - by Adam Ryczkowski
    I have 5 hard drives, where I want to keep my data. Some of my files are more important, and some of them are less. So some of them I wish to put on RAID-6, and for some it RAID-5 is sufficient. It is difficult to predict at the moment of creation of the arrays how much space of each type to declare. What I would do if I didn't hear about zfs, is partition the hard drives into identical 100GB partitions, and as my needs grow, assemble those partitions into md devices using linux-raid. Then, I'd combine those devices using lvm into logical volumes where I'd put my data. So when I'd need more space of e.g. RAID-6, I'd take 100GB partition from each hard drive and assemble them into another RAID-6 md device and would use it as physical storage for the logical volume group dedicated for RAID-6 data. Then I could grow the file system on this logical volume. On top of RAID-6 and RAID-5 Volume Groups (managed by lvm) would reside completely independent file systems, which I'd later merge with multiple mount --bind into a single directory structure that would reflect the logical structure of data rather that of the storage. But now, when I heard about the ZFS with all the performance, data-healing and compression capabilities I cannot stop thinking if it can help me. If so, what do you think would be the best setup?

    Read the article

  • How to Set Up an SMTP Submission Server on Linux

    - by Kevin Cox
    I was trying to set up a mail server with no luck. I want it to accept mail from authenticated users only and deliver them. I want the users to be able to connect over the internet. Ideally the mail server wouldn't accept any incoming mail. Essentially I want it to accept messages on a receiving port and transfer them to the intended recipient out port 25. If anyone has some good links and guides that would be awesome. I am quite familiar with linux but have never played around with MTA's and am currently running debian 6. More Specific Problem! Sorry, that was general and postfix is complex. I am having trouble enabling the submission port with encryption and authentication. What Works: Sending mail from the local machine. (sendmail [email protected]). Ports are open. (25 and 587) Connecting to 587 appears to work, I get a "need to starttls" warning and starttls appears to work. But when I try to connect with the next command I get the error below. # openssl s_client -connect localhost:587 -starttls smtp CONNECTED(00000003) depth=0 /CN=localhost.localdomain verify error:num=18:self signed certificate verify return:1 depth=0 /CN=localhost.localdomain verify return:1 --- Certificate chain 0 s:/CN=localhost.localdomain i:/CN=localhost.localdomain --- Server certificate -----BEGIN CERTIFICATE----- MIICvDCCAaQCCQCYHnCzLRUoMTANBgkqhkiG9w0BAQUFADAgMR4wHAYDVQQDExVs b2NhbGhvc3QubG9jYWxkb21haW4wHhcNMTIwMjE3MTMxOTA1WhcNMjIwMjE0MTMx OTA1WjAgMR4wHAYDVQQDExVsb2NhbGhvc3QubG9jYWxkb21haW4wggEiMA0GCSqG SIb3DQEBAQUAA4IBDwAwggEKAoIBAQDEFA/S6VhJihP6OGYrhEtL+SchWxPZGbgb VkgNJ6xK2dhR7hZXKcDtNddL3uf1YYWF76efS5oJPPjLb33NbHBb9imuD8PoynXN isz1oQEbzPE/07VC4srbsNIN92lldbRruDfjDrAbC/H+FBSUA2ImHvzc3xhIjdsb AbHasG1XBm8SkYULVedaD7I7YbnloCx0sTQgCM0Vjx29TXxPrpkcl6usjcQfZHqY ozg8X48Xm7F9CDip35Q+WwfZ6AcEkq9rJUOoZWrLWVcKusuYPCtUb6MdsZEH13IQ rA0+x8fUI3S0fW5xWWG0b4c5IxuM+eXz05DvB7mLyd+2+RwDAx2LAgMBAAEwDQYJ KoZIhvcNAQEFBQADggEBAAj1ib4lX28FhYdWv/RsHoGGFqf933SDipffBPM6Wlr0 jUn7wler7ilP65WVlTxDW+8PhdBmOrLUr0DO470AAS5uUOjdsPgGO+7VE/4/BN+/ naXVDzIcwyaiLbODIdG2s363V7gzibIuKUqOJ7oRLkwtxubt4D0CQN/7GNFY8cL2 in6FrYGDMNY+ve1tqPkukqQnes3DCeEo0+2KMGuwaJRQK3Es9WHotyrjrecPY170 dhDiLz4XaHU7xZwArAhMq/fay87liHvXR860tWq30oSb5DHQf4EloCQK4eJZQtFT B3xUDu7eFuCeXxjm4294YIPoWl5pbrP9vzLYAH+8ufE= -----END CERTIFICATE----- subject=/CN=localhost.localdomain issuer=/CN=localhost.localdomain --- No client certificate CA names sent --- SSL handshake has read 1605 bytes and written 354 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: E07926641A5EF22B15EB1D0E03FFF75588AB6464702CF4DC2166FFDAC1CA73E2 Session-ID-ctx: Master-Key: 454E8D5D40380DB3A73336775D6911B3DA289E4A1C9587DDC168EC09C2C3457CB30321E44CAD6AE65A66BAE9F33959A9 Key-Arg : None Start Time: 1349059796 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) --- 250 DSN read:errno=0 If I try to connect from evolution I get the following error: The reported error was "HELO command failed: TCP connection reset by peer".

    Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >