Search Results

Search found 16617 results on 665 pages for 'os classic'.

Page 42/665 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• Kernel panic while loading Mac OS X on VMWare

  - by Vladimir Gritsenko

  I'm trying to run Mac OS X 10.6.3 on VMWare 7.1 from within Windows 7 64 bit. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

  Read the article

• Can't connect to a Hyper-V VM from anywhere but the host OS

  - by Elbelcho

  I have an unusual situation on hand where I'm able to connect to a Hyper-V guest VM from the HOST, but not from anywhere but the host. The VM is running WIn2k8R2 and has IIS installed and Remote Desktop enabled. If I browse to the IP from the host OS, the IIS7 page displays. I can also RDP into the guest OS from the host as well as ping. From OFF the host, RDP, web and ping all fail. If I completely shut off the guest VM's firewall, ping will then start to respond, but all RDP and port 80 still don't. The physical host machine has 2 nics installed, but only one is plugged in. The one plugged in has a static IP. I have one Hyper-V virtual network and it's set to external. The guest VM has one NIC with a different static IP than the host, but both are on the same subnet. The host machine is joined to the domain, the guest VM is not. Any sugestions? Thanks so much for any help you may be able to provide!

  Read the article

• Mac OS X L2TP VPN won't connect

  - by smokris

  I'm running Mac OS X Server 10.6, providing an L2TP VPN service. The VPN works just fine when connecting from all computers except one --- this one computer stays at the "Connecting..." stage for a while, then says "The L2TP-VPN server did not respond". In the console, I see this: 6/7/10 10:48:07 AM pppd[341] pppd 2.4.2 (Apple version 412.0.10) started by jdoe, uid 503 6/7/10 10:48:07 AM pppd[341] L2TP connecting to server 'foo.bar.baz.edu' (256.256.256.256)... 6/7/10 10:48:07 AM pppd[341] IPSec connection started 6/7/10 10:48:07 AM racoon[342] Connecting. 6/7/10 10:48:07 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 1). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 2). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 3). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 4). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 5). 6/7/10 10:48:11 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:14 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:17 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). ...and the "retransmit" messages continue until the error message pops up. So far I've unsuccessfully tried: rebooting deleting the VPN profile and recreating it verifying the client's internet connection (it is able to reach the VPN server) connecting through several different networks (in case a router was blocking VPN packets) disabling the Mac OS X Firewall on the client making sure that the VPN settings exactly match those of other working computers running software update (the client is on 10.6.3) Any ideas?

  Read the article

• OS X AFP shares and access

  - by gbrandt

  I am running 10.5.6 Client as a mini server and am having problems with AFP shares. All clients are OS X 10.5.7 I have created three users for 'File Sharing' only on the 'server'. I have created groups and placed these users into specific groups. I have created ACL's to give each group access to certain shares. Two of those users can read and write to any share, one user cannot write to the shares, with different results: when copying a directory, only the directory is created, no files inside are copied, the OS does not give any errors when copying a single file I get three dialogs: "You may need to enter the name and password for an administrator on this computer to change the item named 'xxxx', "The item 'xxxxx' contains one or more items you do not have permission to read. Do you want to copy the items you are allowed to read?, and, The operation cannot be completed because you do not have sufficient priveleges for some of the items. With the single file, a file gets created on the server, but is empty. My ACL for the group this user belongs to is: 0: group:projectmembers allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 1: group:informationtechnology inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 2: group:executive inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 3: group:everyone inherited deny list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit User 1 & 2 belong to informationtechnology and executive and projectmembers, they can read and write freely on the share. User 3 belongs to projectmembers and cannot read and write freely. I have read that this is a UID issue, however User 1 & 2 do not have matching UID's across clients and server and they work, so I don't think this is the case. Any ideas?

  Read the article

• IIS seems to send email twice

  - by David Brunelle

  Hi, we have a request page in our website that send email to confirm the request. It seem that whenever this page is accessed, some (not all of them) are sent more than once at different time, sometime hours apart. The code (which is an old ASP page) looks fine as it sends only once to the recipient. So I doubt it's a programming related problem. When looking at the Exchange server, the tech told me that he seems to be receiving the request twice at different time, so the problem comes from what's between the code and Exchange. My hypothesis is that IIS seem to 'remember' the page and rerun it for some reason. Any hint on where to start? We have IIS 6 (in french if it makes any difference) with Exchange 2007. IIS is running on a Windows Server 2003 machine (virtual machine I believe) in a DMZ. I don't know about Exchange. Thank you.

  Read the article

• Windows Search Indexer keeps taking the focus

  - by Thomaschaaf

  I am trying to watch a video with MPC and then Windows Search Indexer keeps taking the focus.. how do I prevent it from doing that? running Windows 7 with x64

  Read the article

• Installing MySQL 5.1 on OS X 10.7 Lion

  - by xisal

  I am trying to install MySQL 5.1. I am on Lion, and when I remove all files associated with MySQL on my machine it still tells me that I have a newer version installed when I try to install it from the DMG file. Has anyone successfully installed MySQL 5.1 on Lion? I found a solution using Homebrew: Completely remove MySQL from your system (just in case) sudo rm /usr/local/mysql sudo rm -rf /usr/local/mysql* sudo rm -rf /Library/StartupItems/MySQLCOM sudo rm -rf /Library/PreferencePanes/My* vim /etc/hostconfig and removed the line MYSQLCOM=-YES- rm -rf ~/Library/PreferencePanes/My* sudo rm -rf /Library/Receipts/mysql* sudo rm -rf /Library/Receipts/MySQL* sudo rm -rf /var/db/receipts/com.mysql.* Source:http://stackoverflow.com/questions/1436425/how-do-you-uninstall-mysql-from-mac-os-x Install homebrew /usr/bin/ruby -e "$(curl -fsSL https://raw.github.com/gist/323731)" Source: https://github.com/mxcl/homebrew/wiki/installation Install MySQL 5.1 via brew brew install mysql51 if that doesn't work, do this: brew install https://raw.github.com/adamv/homebrew-alt/master/versions/mysql51.rb Source: http://stackoverflow.com/questions/4359131/brew-install-mysql-on-mac-os/6399627#6399627 Make MySQL Work Create mysql.sock file touch /tmp/mysql.sock Install MySQL default tables /usr/local/Cellar/mysql51/5.1.58/bin/mysql_install_db ...or your path Source: http://stackoverflow.com/questions/4788381/getting-cant-connect-through-socket-tmp-mysql-when-installing-mysql-on-ma/5140849#5140849

  Read the article

• Bridged network on OS X only gets UDP broadcast traffic

  - by a paid nerd

  I've created a bridged network Mac OS X 10.8.5 using ifconfig and TUNTAP for OS X to bridge my wireless connection, en0, with a virtual interface, tap0, which I can use for guest VMs: $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 28:cf:xx:xx:xx:xx inet6 xxxx::xxxx:xxxx:xxxx:xxxx%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.64 netmask 0xffffff00 broadcast 192.168.100.1 media: autoselect status: active bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) However, if I tcpdump -i tap0, I only see broadcast traffic. Shouldn't I see a mirror of everything on en0? (192.168.100.33, the host doing the broadcasting, is another unrelate, noisy server on my LAN.) (I asked a similar question here and will probably close it.)

  Read the article

• Data recovery on a data HDD (no OS)

  - by aCuria

  I am helping a family member with a dead hard disk. It is a seagate 200Gb 3.5" HDD in one of those old-school external enclosures. The problem was that windows failed to detect the hard disk when plugged in through USB. I removed the hard disk from its enclosure, and plugged it into my desktop PC. The BIOS does detect it upon POST, but unfortunately windows 7 would refuse to boot. It will get stuck on the loading screen with the glowing windows logo. Safe mode doesn't help either. What options do I have before going for some professional data recovery? edit: Someone modified the Title to something completely different from what I was asking, i just changed it back. 1) 2 HDD drives, DiskA(Dead), DiskB(my OS disk) 2) when B is connected to my system, everything works fine 3) when A AND B is connected, failure to boot. POSTs fine, but windows wont load 4) A has NO OS, its PURE data. It came from an EXTERNAL HDD enclosure which doesnt belong to me, and im trying to do data recovery.

  Read the article

• IIS login Problem to open localhost

  - by Shahid Mahmood Adil

  i have winXp sp2 on my machine. i have installed IIS. when i am trying to open my localhost as http://localhost/ it asks for login and password. when i am using my windows authentication to login creates an error message http 500 internal server error and error detail is error '8002801c' Error accessing the OLE registry. /iisHelp/common/500-100.asp, line 17 how can i resolve this problem?

  Read the article

• fatal error 'stdio.h' Python 2.7 on Mc OS X 10.7.5 [closed]

  - by DjangoRocks

  I have this weird issue on my Mac OS X 10.7.5 /Library/Frameworks/Python.framework/Versions/2.7/include/python2.7/Python.h:33:10: fatal error: 'stdio.h' file not found What caused the above error? This error has been bugging me and i can't install mysql-python as i'm stuck with this step. I'm using Python 2.7.3. Things like Google App Engine ( python ), python script, tornado generally works on my mac. But not mysql-python. I've install MySQL using the dmg image and have copied the mysql folder to /usr/local/ How do i fix this? ======UPDATE====== I've ran the command, and tried to install mysql-python by running sudo python setup.py install. But received the following: running install running bdist_egg running egg_info writing MySQL_python.egg-info/PKG-INFO writing top-level names to MySQL_python.egg-info/top_level.txt writing dependency_links to MySQL_python.egg-info/dependency_links.txt writing MySQL_python.egg-info/PKG-INFO writing top-level names to MySQL_python.egg-info/top_level.txt writing dependency_links to MySQL_python.egg-info/dependency_links.txt reading manifest file 'MySQL_python.egg-info/SOURCES.txt' reading manifest template 'MANIFEST.in' writing manifest file 'MySQL_python.egg-info/SOURCES.txt' installing library code to build/bdist.macosx-10.6-intel/egg running install_lib running build_py copying MySQLdb/release.py -> build/lib.macosx-10.6-intel-2.7/MySQLdb running build_ext gcc-4.2 not found, using clang instead building '_mysql' extension clang -fno-strict-aliasing -fno-common -dynamic -g -O2 -DNDEBUG -g -O3 -Dversion_info=(1,2,4,'rc',5) -D__version__=1.2.4c1 -I/usr/local/mysql/include -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c _mysql.c -o build/temp.macosx-10.6-intel-2.7/_mysql.o -Os -g -fno-common -fno-strict-aliasing -arch x86_64 In file included from _mysql.c:29: /Library/Frameworks/Python.framework/Versions/2.7/include/python2.7/Python.h:33:10: fatal error: 'stdio.h' file not found #include <stdio.h> ^ 1 error generated. error: command 'clang' failed with exit status 1 What other possible ways can i fix it? thanks! Best Regards.

  Read the article

• OS X won't see Windows 7 in network (and vice versa)

  - by meds

  I've enabled SMB sharing in OS X Lion and have added folders to share, it says 'Windows Sharing: On' with a green circle next to it (from the sharing window) and that to access the volume I will need to to go to \\192.168.0.17. It also says that the OS X should be visible as 'macbook' in the network. Both my WIndows 7 and OS X are connected to the same network, yet when I try to go to \\192.168.0.17 or from the Mac try to go to my Windows system (smb://192.168.0.6) the two OSs don't see each other. Any ideas why? Attempting to ping the Mac from Windows results in this output in the command prompt: Pinging 192.168.0.17 with 32 bytes of data: Reply from 192.168.0.6: Destination host unreachable. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.17: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), ipconfig in Windows is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::8918:efd1:b05c:890f%21 IPv4 Address. . . . . . . . . . . : 192.168.0.6 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::98ab:63fc:3c07:d837%13 IPv4 Address. . . . . . . . . . . : 192.168.74.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::80ff:c575:7b50:3a10%14 IPv4 Address. . . . . . . . . . . : 192.168.21.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{2E97D0AE-9E18-4072-AC23-1979BA0DCB79}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{E260CE43-E9A7-4DE0-A88E-4EAFF68ACDDB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{A5130812-59CE-4DDF-9C35-9433BCED9831}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{134BCAE7-CFFF-4A98-8DA0-3708806AABEB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{8D9E3B8F-161C-4ACE-B211-3EDD694416B2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : in OS X: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4> ether c8:2a:14:01:24:c1 media: autoselect (none) status: inactive en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether e0:f8:47:0c:fe:04 inet6 fe80::e2f8:47ff:fe0c:fe04%en1 prefixlen 64 scopeid 0x5 inet 192.168.0.17 netmask 0xffffff00 broadcast 192.168.0.255 media: autoselect status: active p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304 ether 02:f8:47:0c:fe:04 media: autoselect status: inactive fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 70:cd:60:ff:fe:d8:f1:32 media: autoselect <full-duplex> status: inactive

  Read the article

• Copying large files from USB devices to the internal hard drive fails on Mac OS

  - by John M. P. Knox

  I have a second-generation 13" MacBook Air running Mac OS X 10.6.6 with a 2.13 GHz processor, 4 GB of RAM, and a 256 GB SSD hard disk. I often get failures when I attempt to copy a large file or large collection of files from an external USB drive (typically a "Firewire" generation Drobo) to the internal drive. The failure behaves almost exactly as if I had pulled the USB cable from the computer in mid-transfer. I get a warning that I have removed the hard disk improperly. After this event, the drive no longer appears mounted in the finder, and I have to unplug and reinsert the USB cable to mount the drive again. I have also seen a similar problem when using Aperture 3 to import a large number of photos and videos from a USB Compact Flash card reader. The import will fail and I will have to unplug the Card Reader and import the missing items. Oddly, reversing the direction of the copy seems pretty reliable. I've never had a problem copying a large file to a USB device, meaning that I have quite a few large files which are stranded on my Drobo. Model Identifier: MacBookAir3,2 Boot ROM Version: MBA31.0061.B01 I have seen a similar issue reported on Apple's website: http://discussions.apple.com/thread.jspa?threadID=2648590&tstart=0 The only suggested resolutions there seems to be switching to another form of connectivity (e.g. firewire, which does not exist on MacBook Air), or downgrading to Mac OS 10.6.4, or reverting the USB kernel extensions to the 10.6.4 versions: http://discussions.apple.com/message.jspa?messageID=12566073#12582956 I'm not too keen on the idea of downgrading kernel extensions. Does anyone know of a hardware revision without this issue that I can trade up to? Are there any other potential solutions out there?

  Read the article

• How to configure a Web.Config file to allow custom 404 handling while still displaying on-page 500 e

  - by Mark

  To customize 404 handling and based on the hosting company's suggestion, we are currently using the following web.config setup. However, we quickly realized that with this configuration, any page error (500 error) are also getting redirected to this custom error page. How can I modify this config file so we can continue to handle 404 with custom file while still able to view on-page error? <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.webServer> <httpErrors errorMode="DetailedLocalOnly" defaultPath="/Custom404.html" defaultResponseMode="ExecuteURL"> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="/Custom404.html" responseMode="ExecuteURL" /> </httpErrors> </system.webServer> <system.web> <customErrors mode="On"> <error statusCode="404" redirect="/Custom404.html" /> </customErrors> </system.web> </configuration>

  Read the article

• DMG image containing Mac OS X 10.6.5 update not recognized

  - by Lawliet

  Hello, I want to update my Mac OS X 10.6.3 and want to use the manual package update (not Software Update) and I am having this problem for two days now. First I downloaded Mac OS X 10.6.5 Combo update and on the first opening it popped up a message saying "Unable to mount: disk image not recognized". I thought that somehow the image became corrupt during the download, so I downloaded it again. Same result. And I downloaded again. And again... No use, it still states that the .dmg is not recognized. Then I tried to update my system from 10.6.3 to 10.6.4 using the same method (package installer). It worked. And of course I downloaded the 10.6.5 update (not the combo package, but the 10.6.4 10.6.5 update package)... guess what. Not recognized. I don't understand how is this possible. Did anyone has the same problem? Please don't advice me to use software update, as I need to do that on multiple Macs Thanks in advance.

  Read the article

• HP 20gig iPod stuck on "AC Charge" icon

  - by Chris

  I have a HP edition iPod (20gig) and it is stuck on the "AC Charge" icon with the picture of the wall charger and an outlet. I tried to reset the device and it has been stuck on this icon for quite a while now. I have tried everything I can to try to reset it, and before I stoop to visiting an Apple store I want to see if anyone has any tricks up their sleeves. This is what the icon looks like:

  Read the article

• Slow boot for OS and external devices

  - by Derek Van Cuyk

  I have been having this problem intermittently but as of yesterday, it has become more consistent. It originally started when I rebooted my PC at home and the OS (Windows 8) sat in a loop appearing to do nothing while loading. I figured since this was a new installation, that something may have just become corrupted and I decided to reinstall. So I tried to boot off of the thumb drive which had the installation iso and encountered pretty much the same issue. Same with the DVD drive. So, I rebooted once again and left it to load the entire night just to see if it ever would and sure enough this morning, Windows had finally loaded. Authentication had the same roblem albeit not quite as long (took about 5 minutes to authenticate). However, once I was in, everything appeared to be working fine and as quick as normal with the exception of when I tried to scan the C drive for any errors, which ran unbearably slow (45 minutes and before I left for work and was not finished scanning a 64GB SSD drive). I mention that I have had this issue but never when loading the OS. Before it occurred when trying to install windows 7 from a different DVD drive than the one I have now. It took me about 3 hours to do it since I had to wait sometimes 30+ min for each step to finish processing. Does anyone have an idea as to what can cause this? I am assuming it is the motherboard since it is responsible for communication with all the devices I'm having issues with but I cannot find anyone else who has had a problem like this and don't want to drop more money on a MB if it isn't the problem. Hardware: Motherboard: Asus M4A78T-E Socket AM3/ AMD 790GX/ Hybrid CrossFireX Hard Drive: Kingston SSDNow V+180 64GB Micro SATA II 3GB/S 1.8 Inch Solid State Drive SVP180S2/64G Optical Drive: Samsung Blu-Ray Combo Internal 12XReadable and DVD-Writable Drive with Lightscribe SH-B123L/BSBP Thanks, Derek

  Read the article

• Campus VLAN Segmentation - By OS?

  - by Moduspwnens

  We've been thinking through re-arranging our network and VLAN configuration. Here's the situation. We already have our servers, VoIP phones, and printers on their own VLANs, but our problem lies with end user devices. There are just too many to lump on the same VLAN without being hammered with broadcasts! Our current segmentation strategy has them split into VLANs like this: Student iPads Staff iPads Student Macbooks Staff Macbooks Gaming devices Staff (Other) Student (Other) *Note that our network has many more iPads and MacBooks than most. Since the primary reason we're splitting them is just to put them in smaller groups, this has been working for us (for the most part). However, this required our staff to maintain access control lists (MAC addresses) of all devices belonging in these groups. It also has the unfortunate side effect of illogically grouping broadcast traffic. For example, using this setup, students on opposite ends of campus using iPads will share broadcasts, but two devices belonging to the same user (in the same room) will likely be on completely separate VLANs. I feel like there must be a better way of doing this. I've done a lot of research and I'm having trouble finding instances of this kind of segmentation being recommended. The feedback on the most relevant SO question seems to point toward VLAN segmentation by building/physical location. I feel like that makes sense because logically, at least among miscellaneous end users, broadcasts will typically be intended for nearby devices. Are there other campuses/large-scale networks out there segmenting VLANs based on end-system OS? Is this a typical configuration? Would VLAN segmentation based on physical location (or some other criteria) be more effective? EDIT: I've been told that we will soon be able to dynamically determine device OS without maintaining access lists, although I'm not sure how much that affects the answers to the questions.

  Read the article

• is it worth defragging an iPod

  - by alimack

  Essentially my 5G iPod was cutting tracks off and generally misbehaving. So I did the following: 1) Use Diskwarrior - heavy directory fragmentation which it fixed; 2) Use iDefrag - some fragmentation but it kept halting as it couldn't move files; 3) Try to write out drive with Disk Utility - got a warning from DU so gave up before I started; 4) Completely restored using iTunes; 5) Reran Diskwarrior - still heavy directory fragmentation; 6) Reran iDefrag, still fragmentation although limited to two bands; The iPod is much quicker to traverse menus and no more track skipping. My question is this - is defragging worth it or does the heat generated by the process kill the drive and make it a self-defeating process. Anyone have any metrics/ figures? Clearly it's a bad idea for solid state drives like the nano & touch.

  Read the article

• IIS ASP Redirect Removal

  - by Kim L

  We have a website that is setup on IIS 7 and are trying to replace it with a new site, but need a redirect that is in place removed. The old site used a custom file as the homepage (WN-main.asp). We removed all the old site files, including web.config, and placed them in a subdirectory for safe keeping. The new site no longer uses ASP, and we'd like to use a regular index.html as the default. However, when we go to the website, it keeps trying to redirect our .com to .com/WN-main.asp -- and that gives us a 404 Error in the Application for "Default Web Site" because we removed that page. In the IIS "Default Document" settings we have index.html at the top, and WN-main.asp is nowhere to be found in the list (it never was there). We've also removed the web.config file from the root directory, and put the entire old website in a subdirectory. As well as restarted IIS. We're assuming that the redirect is setup somewhere in IIS because if I navigate to .com/index.html which is our new site, it works. Our problem is that oursite.com redirects to oursite.com/WN-main.asp. Grr. If you go to www.worzalla.com you can see how it redirects to the WN-main.asp page right now as the homepage. Any ideas where this redirect could have been setup so we can remove it? Thanks!

  Read the article

• Cross OS data recover question, USB drive involved.

  - by Moshe

  Here's the story: A MacBook had OS X 10.4 and Windows XP dual booting using rEFIt. Then the Windows partition gets corrupted and it won't boot. Presumably a virus. There were sensitive files there and those were successfully copied to a USB drive and then 10.5 was installed on the hard drive, formatting the drive in the process. The USB drive's contacts cracked and he data is lost from there, unless it can be resoldered. The issues is that there is too much solder there already. So, how can the data in question be recovered? The files were Microsoft Money (not the latest version) files for the Windows version of the program. Right now, only OS X is installed on the MacBook. Is there Mac based program that can recover the Windows data or am I better off trying to resolder the drive? Does anyone know how to best resolder a USB drive more than once, where the first solder is ther, but detached from the silicon? Also, what format (extension) are Microsoft Money files? In need of help!

  Read the article

• Mac OS X Lion Apache Server not Found

  - by Burak Erdem

  After upgrading to Lion 10.7.2 today, Apache virtual hosts are not working anymore. When I go to http://XYZ.localhost, it say "server not found". I am using Apache on my Mac OS X Lion and until today, it was working fine. I can access http://localhost but I can't access http://XYZ.localhost My /etc/hosts file is like below; 127.0.0.1 XYZ.localhost My /etc/apache2/extra/httpd-vhosts.conf file is like below; <VirtualHost *:80> ServerName XYZ.localhost DocumentRoot /Library/WebServer/Documents/XYZ <Directory /Library/WebServer/Documents/XYZ> DirectoryIndex index.php AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> I think I once had this problem too, after another OS X update, but I can't remember how I solved it. Is it a user permission issue? Or is there something wrong with Apache or any other setting? EDIT: It seems like my /etc/hosts file is not working correctly. Even if I add something like 127.0.0.1 apple.com it still goes to the real apple.com. Maybe this might help to solve the problem.

  Read the article

• IIS login Problem to open localhost

  - by Shahid Mahmood Adil

  i have winXp sp2 on my machine. i have installed IIS. when i am trying to open my localhost as http://localhost/ it asks for login and password. when i am using my windows authentication to login creates an error message http 500 internal server error and error detail is error '8002801c' Error accessing the OLE registry. /iisHelp/common/500-100.asp, line 17 how can i resolve this problem?

  Read the article

• How to play 24 fps video smoothly on a 60Hz display?

  - by netvope

  I use mpc-hc to play videos on Win7 x64. With the default settings (#1), video playback is great most of the time. But for panning shots, playback is not smooth. I stepped through the video frame by frame and found that the panning movement is smooth (e.g. each frame shifts horizontally by 10 pixels), so the problem is how the 23.976 fps video is interpolated to 60Hz. The judder looks like what would be caused by a "2:3 pulldown", where the frames are played unevenly like: frame 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, etc (#2) Using "optimal renderer settings" (#3) instead of the default disables the Aero theme and causes tearing. Setting my LCD display to 50Hz may have improved the judder slightly (but I can't really tell). My display does not support 24Hz or 48Hz, and forcing them in the Nvidia control panel gives blurry screen. I've tried other video players (VLC and KMPlayer), the ReClock Directshow Filter, video files from different sources (#4), turning on/off DXVA, and a computer with a different GPU, but the judder in the playback is similar. None of them solved the problem. So, how can I play 23.976 or 24 fps video smoothly on a 60Hz display? I think a video player could make the video smoother by doing linear interpolation, such as: 1. 100% frame 1 2. 60% frame 1 + 40% frame 2 3. 20% frame 1 + 80% frame 2 4. 80% frame 2 + 20% frame 3 5. 40% frame 2 + 60% frame 3 6. 100% frame 3 7. 60% frame 3 + 40% frame 4 .. etc Can any existing video player do this? Footnotes: (#1) Video renderer: EVR Custom Pres. (#2) This example converts a 24 fps video into 30 fps (#3) View Renderer settings Reset Reset to optimal renderer settings (#4) The files I have are all H.264 mkv files, but I don't think the file format/encoding matters.

  Read the article

• OS X can connect to Windows machine, but can't access shared folders

  - by Bonnie

  I can create new folders on my Windows XP machine, set them to "shared". On my Mac, I pick Finder → Go → Connect to Server → smb://192.168.1.4 → Connect → Name / Password. It even shows me all the names of the newly created shared-folders on my PC, but when I try to actually connect to any of them I get connection failed, there was an error connecting Any idea on what would cause that? The fact that it successfully gets so far—to actually showing me my PC share-names—must mean I have 99% of this working correctly, i.e. the physical connection, the IP address, the user name, the password, etc. Still, I can't seem to access the folders themselves. I've tried this with my Windows XP firewall on/off, and Norton AntiVirus on/off. Same problem. Everything did work fine, 4 months ago. Were there any odd OS X or Windows updates released recently? I always apply them all. smbclient on the Mac does correctly find the XP machine, my XP user name, and accepts my XP password. I get the following from that smbclient command: Doing spnego session setup (blob length=16) server didn't supply a full spnego negprot Got challenge flags: ... Got NTLMSSP flags: ... Got NTLMSP flags: ... Domain=[XPMACHINE] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] tree connect failed: NT_STATUS_INSUFF_SERVER_RESOURCES I'm not sure why a standard XP box can't "supply a full spnego negprot". Whatever that means. Using XP's RegEdit to change my IRPStackSize from 11... to 13, 15, 20, 22... still gives that "NT_STATUS_INSUFF_SERVER_RESOURCES" error on the Mac.

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >