Search Results

Search found 11427 results on 458 pages for 'live cd'.

Page 420/458 | < Previous Page | 416 417 418 419 420 421 422 423 424 425 426 427  | Next Page >

• dd-wrt router firmware QoS troubleshooting

  - by Jeff Atwood

  I've been using the dd-wrt firmware on my router and I like it a lot! But -- I'm not sure the quality of service (QoS) is working on it. I have it set up as follows: http, port 80 -- Premium bittorrent, port 6969 -- Bulk https, port 443 -- Premium dns, port 53 -- Premium Per the QoS documentation, these levels are: bandwidth is allocated based on the following percentages of uplink and downlink values for each class: Exempt: 100mbps - ignores global limits. Premium: 75% - 100% Express: 15% - 100% Standard: 10% - 100% Bulk: 1.5% - 100% This doesn't entirely seem to work, though -- with busy torrents going I get major pauses in my web browsing which sucks! The QoS documentation gives some steps to check the QoS ... What you'll be interested to look at will be the first set of source and destination IP, including the port numbers. Next the presence of l7proto and the "mark" field. The entries indicate the current live connection QoS priority applied on them based on the "mark" field. The "mark" values correspond to the following Exempt: 100 Premium: 10 Express: 20 Standard: 30 Bulk: 40 (no QoS matched): 0 You may see "mark=0" for some l7proto service even though they are in configured in the list of QoS rules. This may mean that the layer 7 pattern matching system didn't match a new or changed header for that protocol. Custom service on port matches will usually take care of these. On port 6969 (bittorrent) I see a weird mixture of stuff with mark=0 and mark=40 like so cat /proc/net/ip_conntrack udp 17 105 src=98.162.182.42 dst=1.2.3.4 sport=64512 dport=6969 packets=3 bytes=290 src=10.0.0.2 dst=98.162.182.42 sport=6969 dport=64512 packets=4 bytes=202 [ASSURED] mark=0 secmark=0 use=1 tcp 6 117 TIME_WAIT src=98.248.173.174 dst=1.2.3.4 sport=51114 dport=6969 packets=12 bytes=704 src=10.0.0.2 dst=98.248.173.174 sport=6969 dport=51114 packets=10 bytes=440 [ASSURED] mark=40 secmark=0 use=1 tcp 6 598 ESTABLISHED src=165.132.128.201 dst=1.2.3.4 sport=57218 dport=6969 packets=8024 bytes=9919881 src=10.0.0.2 dst=165.132.128.201 sport=6969 dport=57218 packets=4211 bytes=239607 [ASSURED] mark=0 secmark=0 use=1 tcp 6 586 ESTABLISHED src=68.46.9.24 dst=1.2.3.4 sport=64688 dport=6969 packets=6 bytes=490 src=10.0.0.2 dst=68.46.9.24 sport=6969 dport=64688 packets=8 bytes=944 [ASSURED] mark=40 secmark=0 use=1 udp 17 45 src=222.254.228.38 dst=1.2.3.4 sport=25438 dport=6969 packets=5 bytes=454 src=10.0.0.2 dst=222.254.228.38 sport=6969 dport=25438 packets=3 bytes=154 [ASSURED] mark=0 secmark=0 use=1 ( full file visible at http://pastebin.com/AZE6EtWm ) I've been playing around with this log for a little while and I can't see any patterns! Why is some port 6969 bittorrent traffic tagged mark=0 (not matched) by dd-wrt's QoS while others are tagged mark=40 (Bulk) .. any ideas?

  Read the article

• Unecrypted Image of Truecrypt-Encrypted System Partition

  - by Dexter

  The general tenor around the internet seems to be that you can't create images of system partitions that have been encrypted (with truecrypt) other than with dd or similar sector-by-sector copy tools. These files however are very impractical given their size (and are obviously incompressible) which makes keeping multiple states/backups of your system partition rather expensive (..especially considering current hdd prices). The problem is that backup tools (like Acronis True Image, Clonezilla, etc.) won't give you the option to create an image of (mounted/opened) Truecrypt partitions, or that there is no recovery environment for restoring the backup, that would allow to run truecrypt before doing any actual restoring. After some trial and error however, I believe I have found a very simple way. Since Truecrypt (running in Linux) creates a virtual block device, that it uses for mounting the unencrypted partitions into the file system, partclone can be used for creating/restoring images. What I did: boot up a linux live disk mount/open the drive/device/partition in truecrypt unmount the filesystem mount point again, like so: umount /media/truecryptX ("X" being the partition number assigend by truecrypt) use partclone (this is what clonezilla would do too, except that clonezilla only offers you to back up real drive partitions, not virtual block devices): partclone.ntfs -c -s /dev/mapper/truecryptX -o nameOfBackupFile for restoring steps 1-3 remain the same, and step 4 is partclone.ntfs -r -s nameOfBackupFile -o /dev/mapper/truecryptX A backup and test-restore of the system (with this method) seems to have worked fine (and the changed settings were reverted to the backup-state). The backup file is ~40 GB (and compressible down to <8GB with 7zip/LZMA2 on the "fast" setting). I can't quite believe that I'm the only one that wants to create images of encrypted drives, but doesn't want to waste 100GB on the backup of one single system state. So my question now is, given how simple this was, and that no one seems to mention anywhere that this is possible - did I miss something? or did I do something wrong? Is there any situation that I didn't think of where this method will fail? Obviously, the backup file needs to be stored in some other encrypted place in order to still remain confidential, since it is unencrypted. Also, in order to do a full "bare metal" restore, one would have to actually first (re-)install Windows, encrypt it, and only then restore the backup file. The funny thing however is that you won't need to backup any partition tables, etc. since the reinstall will effectively take care of that. Is there anything else? This is imho still a lot better than having sector-by-sector images..

  Read the article

• DCHP and Router load testing

  - by John H

  I manage a campground wifi network with an average of 10 - 60 active users. I have encountered issues where the router starts acting flaky (failing to assign DHCP or failing to pass traffic) without any clear warning (low cpu utilization, etc). I upgraded the router a couple times and ended up with a Netgear ProSafe VPN router that seems to be handling the traffic. The interesting thing is that the Netgear has lower specs than the Buffalo router it replaced, indicating the issue is with the DD-WRT firmware. While I'll be pursuing this issue on the dd-wrt forums, I need a way to test routers. My vision is having 1-2 computers connected on the LAN side and 1-2 computers connected on the WAN side. I want the LAN computers to be generating various type of traffic and connections, as well as requesting DCHP addresses. A few notes: The wireless aspect should be a non-issue. Most clients would connect to a wireless bridge and come into the router through a network cable. I had a monitoring server with Nagios running check_dhcp against the router. This server was connected directly by a network cable, eliminating wifi bridges and other devices from the equation. This question is somewhat related, but not exactly: Load testing wireless LANs I am going to look at IxChariot. While I'd ideally like to use a 1 computer on each side running Linux and preferably free software, I can entertain running Windows, multiple computers, or non-free software. Total bandwidth doesn't seem to be the issue. I can transfer large files all day. Even on the busiest days, the users seemed to only pull ~5Mbps. There is very little "LAN to LAN traffic" and most of it might never have reached the main router. The issue I need to test for seems to be tied to active users, or more appropriately, active sessions. I know active users or active clients is a meaningless term from a router standpoint and wouldn't mind having more appropriate terms to use. Summary: I need a way to test a routers ability in handling traffic from a large number of clients. My current strategy is to purchase a router, deploy it, and see how it fails in the live environment.

  Read the article

• Is DHCP lease expriring years from now okay?

  - by sharptooth

  I'm reviewing Azure web role logs and there's output from ipconfig /all IPv4 Address. . . . . . . . . . . : 10.61.145.37(Preferred) . Subnet Mask . . . . . . . . . . . : 255.255.254.0. Lease Obtained. . . . . . . . . . : Monday, September 24, 2012 12:26:00 PM. Lease Expires . . . . . . . . . . : Thursday, October 31, 2148 6:55:12 PM. you see, the lease expires in year 2148 but my VM will likely not run for more than one month - when I deploy the new version of my code I first deploy it to new VMs, then switch traffic, then release the new VMs. In general such usage pattern is normal - VMs typically live from several dozen minutes to several weeks on Azure. I suspect the lease that long will cause problems on the internal Azure network sooner or later. Is such long DHCP lease okay or is it likely a misconfiguration?

  Read the article

• How to use more than 3 virtual disks in Linux using CentOS and XenServer

  - by 010110110101

  I've attached 5 virtual disks to a Virtual Machine in Citrix XenServer. The VM has the xs-tools installed. Initially it said that it couldn't add so many disks. After I installed the xs-tools, it let me add all the disks. But /dev doesn't show all the disks. It shows these: /dev/xvda /dev/xvdb /dev/xvdc /dev/cdrom Perhaps it is bound by the limits of an IDE bus? (3 disks + CD-ROM) If so, how does one change the VM to use SCSI? Edit: According to the documentation: 2.6.3. VM Block Devices In the PV Linux case, block devices are passed through as PV devices. XenServer does not attempt to emulate SCSI or IDE, but instead provides a more suitable interface in the virtual environment in the form of xvd* devices. It is also possible to get an sd* device using the same mechanism, where the PV driver inside the VM takes over the SCSI device namespace. This is not desirable so it is best to use xvd* where possible for PV guests (this is the default for Debian and RHEL). For Windows or other fully virtualized guests, XenServer emulates an IDE bus in the form of an hd* device. When using Windows, installing the Citrix Tools for Virtual Machines installs a special PV driver that works in a similar way to Linux, except in the fully virtualized environment. Still, with 5 virtual disks attached, I don't see the other xvd devices. Edit #2: (attached requested info) Host Machine: XenServer 6.1 Linux version 2.6.32.43-0.4.1.xs1.6.10.777.170770xen (geeko@buildhost) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-51)) #1 SMP Wed Apr 17 05:52:03 EDT 2013 Guest Machine: CentOS release 6.4 (Final) Linux version 2.6.32-358.6.2.el6.x86_64 ([email protected]) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Thu May 16 20:59:36 UTC 2013 Output of 'fdisk -l' on Guest Machine: Note, the disk beyond the first 3 attached are not displaying -- there should be 4 100GB disks. (There are a total of 5 disks displayed in XenCenter -- 16GB, 100GB, 100GB, 100GB, 100GB) Disk /dev/xvdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfb6c95b9 Device Boot Start End Blocks Id System /dev/xvdb1 1 13054 104856223+ 83 Linux Disk /dev/xvda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e5f41 Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2089 16264192 8e Linux LVM Disk /dev/xvdc: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed249ced Device Boot Start End Blocks Id System /dev/xvdc1 1 13054 104856223+ 83 Linux Disk /dev/mapper/vg_blue-lv_root: 14.6 GB, 14571012096 bytes 255 heads, 63 sectors/track, 1771 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_blue-lv_swap: 2080 MB, 2080374784 bytes 255 heads, 63 sectors/track, 252 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 I see that the Linux versions say SMP. The Guest VM doesn't say "xen" in the name. However, I have already run yum install kernel-xen. Could be a clue?

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• How do I reset/update my BIOS for Optiplex GX280?

  - by Sam Langlhey

  So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

  Read the article

• long access times and errors in iis application

  - by Jens Olsson

  Hi, I am having an issue with an IIS application (details of environment at the end of the message). The web site works great most of the time and I cannot reproduce any error in our test system. On the live system however with on averare of 5-15 requests per second I have a problem with that some requests (about 0.05%) will take over 300 seconds to complete. The other requests complete withing 5-10 seconds. It seem like if all the errornous requests end up with a Timer_EntityBody error in the error log. I have never seen this as an end user but I guess that they will receive some kind of error message. I am trying to find out what can be causing this errornous behaviour. Any ideas are welcome. I have read something about that there can be an MTU issue if ICMP and MTU protocols are blocked in the firewall. Does that sound reasonable? I have also read about updating to IIS 7 should do the trick. Does it sound reasonable? I think that the problem has another cause but I have no idea of what. I have tried running hte perormance monitor, monitoring for database locks and active transaction counts. I can see some of these in the perfmon log for the MSSQL server (another machine) for example: Active transactions is sometimes peaking and sometimes for long periods Lock waits per seconds is sometimes peaking Transactions per second is sometimes peaking Page IO Latch wait is sometimes peaking Lock wait time (ms) is sometimes peaking But I cannot see that any of these correlate to the errors in the IIS error log. On the IIS server machine I can also see with perfmon that some values peak a few times during a day: Request execution time Avg disk queue length I can neither see that any of these correlate to the errors in the IIS error log. In the below code I have anonymized by replacing some parts with HIDDEN The following can be seen in the access log 2010-10-01 08:35:05 W3SVC1301873091 **HIDDEN** POST /**HIDDEN**/Modules/BalanceModule.aspx - 80 - **HIDDEN** Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+5.1;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.4506.2152;+.NET+CLR+3.5.30729;+.NET4.0C;+.NET4.0E) ASP.NET_SessionId=**HIDDEN** 400 0 64 0 2241 127799 At the same time the following can be seen in the error log: 2010-10-01 08:35:05 **HIDDEN** 1999 **HIDDEN** 80 HTTP/1.0 POST /**HIDDEN**/Modules/BalanceModule.aspx - 1301873091 Timer_EntityBody Test+Pool I can tell the following about the environment: Server: Windows Server 2003 x64 SP2 running on VMWare HTTP Server: IIS v6.0 with ASP.NET 2.0.50727 Antivirus: Trend Micro OfficeScan (Is it a good idea to have this on a server?)

  Read the article

• Wi-Fi Stick with ZD1211 chip refuses to work on Ubuntu >8.10. No clue.

  - by Benjamin Maus

  I have a machine running Ubuntu 9.10 (Karmic *x86_64*). Everything is running smooth so far, except for the Wi-Fi USB Stick. The same device worked perfectly in 8.10. The wireless device is a GW-US54GXS using the Zydas Zd1211 chipset. Dmesg output after plugging in: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' [ 196.304209] zd1211rw 2-1:1.0: phy0 [ 196.304227] usbcore: registered new interface driver zd1211rw [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Syslog output: Nov 5 11:20:24 somesystem kernel: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' Nov 5 11:20:24 kierkegaard NetworkManager: <info> Found radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/ieee80211/phy0/rfkill0) (driver <unknown>) Nov 5 11:20:24 somesystem kernel: [ 196.304209] zd1211rw 2-1:1.0: phy0 Nov 5 11:20:24 somesystem kernel: [ 196.304227] usbcore: registered new interface driver zd1211rw Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): new 802.11 WiFi device (driver: 'zd1211rw') Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2 Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): now managed Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): device state change: 1 -> 2 (reason 2) Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): bringing up device. Nov 5 11:20:24 somesystem kernel: [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:24 somesystem kernel: [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 Nov 5 11:20:24 somesystem kernel: [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- Nov 5 11:20:24 somesystem NetworkManager: <WARN> nm_device_hw_bring_up(): (wlan0): device not up after timeout! Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): deactivating device (reason: 2). Nov 5 11:20:24 somesystem kernel: [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:29 somesystem wpa_supplicant[978]: Could not set interface 'wlan0' UP Nov 5 11:20:29 somesystem wpa_supplicant[978]: Failed to initialize driver interface Nov 5 11:20:29 somesystem NetworkManager: <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. Gnome tells me in the network menu that the device was "not ready". It appears in iwconfig but not in ifconfig. The same symptoms appear when I boot from the live CD. How can I solve this dilemma?

  Read the article

• Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

  - by Quanano

  We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

  Read the article

• mac + parallels and https site test = router restarts

  - by Erik

  Ok I have an interesting & very frustrating problem happening. I'm going to explain it the best I can. I work as a graphic designer & web designer on a mac and have a Comcast internet connection that comes through a Comcast branded router (SMC8014) which then ties into an Airport Extreme Base Station which runs my office network. I run OS 10.5.7 and also run Parallels 4.0.3 (running Windows XP) for testing websites in Internet Explorer and so on. Ok, so that the basic background. Here's my issue. I've been collaborating an ecommerce website with another designer/developer and when testing the site on the PC side we have started to run into some sort of network problem. The site is https if that matters at all I suspect it may. Basically when I run parallels for testing I am constantly having to restart the router in order to connect to the test site (it's hosted). Funny thing is I can access the rest of the internet fine, just not this site I'm working on until I restart the router (It's sorta like the site is timing out). This never happens when just running the Mac side of things. It only becomes an issue when Parallels is open and I am doing page refreshes while making css or HTML edits via something like Coda or CSS edit (connected to the hosting server via ftp). The real problem is that once the problem starts I only get about 2 or 3 page loads before I have to restart the router again. It's absolutely crippling. I cannot get any work done when I have to restart the router every couple of minutes. So, if you think this problem is isolated to me, the answer is no. The designer/developer I'm collaborating with has an office a couple miles away and experiences very similar problems under slightly different setup. He also has Comcast as his internet provider and connects his router to an Airport and primarily works on a mac. The main difference is that rather than using a visualizer like parallels to test the website on the PC he uses a real live PC that is on his network. Once he fire up the PC to do testing he runs into the same issue described above. After a couple of page refreshes in Internet Explorer or other browser on the PC the site becomes unresponsive and the router has to get restarted. Any thoughts on what is going on here would be greatly appreciated. Thanks in advance.

  Read the article

• Building a Mac/PC Network in a Dorm with Network Restrictions

  - by user70340

  I have been a Windows XP user for the last few years, but I recently bought a 15'' MacBook Pro for research purposes. I would like to set up a no-hassle Mac/PC Network at home so that I can access the internet on both computers and hardware between computers (i.e. a harddrive, or a mouse/keyboard with Synergy). Unfortunately, I live in a dorm with silly network restrictions so a solution is not straightforward. In particular: The dorm has a wired and wireless network, both which provide an internet connection. The wired network provides way faster internet (download speeds of 15 MB/s vs. 2 MB/s on wireless), so I would like to somehow exploit this, at least on my PC for Bittorrent :) Multiple devices can connect to the wireless network, but cannot "see" each other on the network (so software like Synergy would not work). Only 1 MAC address can connect to the wired network at a time. Ideally I would just connect a wireless router to the wired network and then have both the Mac and the PC on that, but the 1 MAC address restriction will not allow the both computer to access the internet simultaneously. I cannot think of a way to bypass this restriction (though I'm not network savvy), so I am planning to create a private no-internet network to allow the devices to see each other and share hardware. Here are some thoughts. I would appreciate any feedback at all! If I build a private wireless network: (first choice) I will use a wireless router that is not connected to the internet. My PC and Mac will be connected to each other wirelessly. I can then connect the PC to the internet via a wired network, but then the Mac will not have internet access as its wireless card is already in use. In this case, could I stream internet access from the PC to the Mac via the wireless network? Or could I buy a USB wireless card for the Mac so that it can connect to both my private network and the dorm network? If I build a private wired network: (second choice) Then both the PC and the Mac will connect to the internet wirelessly, which means I cannot take advantage of the faster download speeds.

  Read the article

• ovs-vsctl: "eth0" is not a valid UUID

  - by Przemek Lach

  I'm trying to setup an open v-switch inside my Ubuntu 12.04 Server VM. I have created three interfaces for this VM and I want to create a port mirror inside of the VM using these there interfaces and open v-switch. There are three Host-Only Adapters: eth0, eth1, eth2. The idea is that three other VM's will be connected to these adapters. One of these VM's will stream UDP video to eth0 and I want the vswitch'd VM to mirror those packets from eth0 onto eth1 and eth2. Each of the VM's connected to eth1 and eth2 will get the same video stream. I performed the following steps to install open v-switch: $ apt-get install python-simplejson python-qt4 python-twisted-conch automake autoconf gcc uml-utilities libtool build-essential $ apt-get install build-essential autoconf automake pkg-config $ wget http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ tar xf http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ cd http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ apt-get install libssl-dev iproute tcpdump linux-headers-`uname -r` $ ./boot.sh $ ./configure - -with-linux=/lib/modules/`uname -r`/build $ make $ sudo make install After installation I configured as follows: $ insmod datapath/linux/openvswitch.ko $ sudo touch /usr/local/etc/ovs-vswitchd.conf $ mkdir -p /usr/local/etc/openvswitch $ ovsdb-tool create /usr/local/etc/openvswitch/conf.db Then I started the server: $ ovsdb-server /usr/local/etc/openvswitch/conf.db \ --remote=punix:/usr/local/var/run/openvswitch/db.sock \ --remote=db:Open_vSwitch,manager_options \ --private-key=db:SSL,private_key \ --certificate=db:SSL,certificate \ --bootstrap-ca-cert=db:SSL,ca_cert --pidfile --detach --log-file $ ovs-vsctl –no-wait init (run only once) $ ovs-vswitchd --pidfile --detach The above steps I got from this tutorial and it all worked fine. I then proceeded to add a port mirror based on the open v-switch documentation under Port Mirroring. I successfully completed the following commands: $ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 eth1 $ ovs-vsctl add-port br0 eth2 $ ifconfig eth0 promisc up $ ifconfig eth1 promisc up $ ifconfig eth2 promisc up At this point when I run ovs-vsctl show I get the following: 75bda8c2-b870-438b-9115-e36288ea1cd8 Bridge "br0" Port "br0" Interface "br0" type: internal Port "eth0" Interface "eth0" Port "eth2" Interface "eth2" Port "eth1" Interface "eth1" And when I run ifconfig I get the following: eth0 Link encap:Ethernet HWaddr 08:00:27:9f:51:ca inet6 addr: fe80::a00:27ff:fe9f:51ca/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth1 Link encap:Ethernet HWaddr 08:00:27:53:02:d4 inet6 addr: fe80::a00:27ff:fe53:2d4/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth2 Link encap:Ethernet HWaddr 08:00:27:cb:a5:93 inet6 addr: fe80::a00:27ff:fecb:a593/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth3 Link encap:Ethernet HWaddr 08:00:27:df:bb:d8 inet addr:192.168.1.139 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fedf:bbd8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2211 errors:0 dropped:0 overruns:0 frame:0 TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:182987 (182.9 KB) TX bytes:125441 (125.4 KB) NOTE: I use eth3 as a bridge adapter for SSH'ing into the VM. So now, I think I've done everything correctly but when I try to create the bridge using the following command: $ ovs-vsctl -- set Bridge br0 mirrors=@m -- --id=@eth0 get Port eth0 -- --id=@eth1 get Port eth1 -- --id=@m create Mirror name=app1Mirror select-dst-port=eth0 select-src-port=@eth0 output-port=@eth1,eth2 I get the following error: ovs-vsctl: "eth0" is not a valid UUID I don't understand why it's not able to find the interfaces?

  Read the article

• Thunderbird 3: can't change column width?

  - by rumtscho

  I recently installed Thunderbird 3.0.3. Just noticed a suboptimal UI setting: in the upper pane, which lists the e-mails in the current folder, the Date column is about 200px wide. So when I keep the window at 480x600, all I see in a row is: | tree icon | favourites icon | attachment icon | read icon | junk icon | Date and time, followed by 5cm whitespace | ... | P Where "P" is the first letter of the name of the sender. And the "..." is actually shown this way, I have no idea which column it is meant to be. But I don't see neither the sender, nor the message subject, which makes scrolling a folder for a certain mail rather pointless. I see these when I maximize the window, actually the columns are then not only bigger, they are arranged in another sequence. But I feel that holding a mail client permanently maximised at 1600x1200 is a waste of screen real estate. My naive solution attempt was to try to go with the mouse cursor to the right edge of the date column and try to shrink it by moving the cursor left while holding down the left mouse button. Not only is this default behaviour for all resizable columns I've ever encountered in GUIs, the cursor actually turns into a horizontal double-headed arrow. But pulling has no effect at all. I cannot make a wide column narrow, and I cannot make the narrow columns wide. I didn't find anything in the preferences either. So can please somebody explain how to get the columns arranged sensibly? Edit: I found out that I only have the problem when I drag the Thunderbird window to a GridMove screen area. It gets automatically resized, but doesn't notice the resize event or something, so the column width remains the same as under a maximized window. First making the window narrow using the mouse helps with column width, but the width of the mail pane is still too wide (rows don't reflow). Anyway, this seems to be a bug caused by the combination of the two applications and not a configuration problem, so I guess I'll have to live with it.

  Read the article

• Unable to burn Windows ISO from Fedora

  - by user331947

  First of all, English is not my native tongue, so apologies for any mistakes. My computer recently started prompting that it can't launch Windows successfully. So I just choose start Windows normally. Then, I found that the startup freezes at the Windows screen (before the login prompt). I have tried rebooting several times and get the same results. So I just gave up. After few days, I tried to boot up my laptop again. This time it got to the desktop, but it's extremely slow and the icons on my Desktop don't show up. I decided to format the Windows partition and reinstall a new one. (It is usually faster that way since I kept my 400GB+ data on aother partition and programs and the rest in the same partition as Windows). The thing is I get the Windows disc at the moment (Traveling aboard). But I have a Windows 7 disc image on my hard disk. So, I downloaded Ubuntu 14.04 LTS, made a Live USB, and then try to burn the image from Ubuntu. But the program just freezes and I don't know why. I tried several times and it's still the same. So I tried using Fedora instead, just to see if it will work. The Disk Image Writer report something like this. Error unmounting /dev/dm-0: Command-line `umount "/dev/dm-0"' exited with non-zero exit status 32: umount: /: target is busy (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1).) (udisks-error-quark, 14) Also, I tried installing linux on the windows partition. The installation program freezes (both Ubuntu and Fedora). So, I thought that maybe something are wrong with my hard disk. I seek the solution on the internet and found that gparted can be used to format a partition. And it also froze at "Searching /dev/sda/ partition ...". I'm using Lenovo Y570. Spec below. http://www.notebookreview.com/notebookreview/lenovo-ideapad-y570-review-a-lenovo-bestseller/3/ Can anyone suggest a next step in diagnosing and fixing this problem? Thanks in advance.

  Read the article

• What issues ensue from having multiple versions of Office installed?

  - by Michael Sorens

  My ultimate question is embodied in the title but I thought it might be helpful to others if I detail what instigated my inquiry and my examination of the problem. To me, the first rule of software updates is Primum non nocere -- first, do no harm. So with my Windows 7 system containing both Office 2003 and Office 2010 I blithely proceeded to install this month's updates from Microsoft, containing updates for both versions of Office. While Microsoft officially does not recommend running multiple versions (see, for example, Running Multiple Versions of Microsoft Excel it is possible; I have had two versions installed for a year or more and have never run into an issue before. One thing that is always mentioned is installation order, i.e., the one you want to open files by default should be installed last. I wanted 2010 as my default so I had indeed installed 2003 first then, years later, 2010. So with this round of Windows updates, either it installed patches to 2010 before 2003, knocking out the file association, or the 2003 patch was more comprehensive, in the sense of touching the file association while the 2010 did not. In any case, after updates, double-clicking a .xls file opened 2003 rather than 2010. Web search indicated either: Use the file associations control panel to re-associate .xls files with the correct version of excel. I looked at this first, but it showed what seemed to be an unversioned "Excel" associated with .xls files so I did not check further. (This turned out to be an error on my part; more later.) Re-install versions in the desired order; I find this unreasonable. Run the repair option of the Office installer on the desired version; still seems more work than one should need. Run excel from the command line with "/regserver" on the one to be the default and "/unregserver" on the other. Good idea, but further search indicated that neither 2007 nor 2010 support "/regserver" contrary to some posts (e.g. Default Program With Multiple Versions Installed). Since this was a Windows Update issue and Microsoft provides free support for such, I inquired there as well, but succeeded only in getting the suggestion to uninstall all other versions, period; not acceptable to me. What worked for me was going back to the file associations control panel and manually selected the Office 2010 version of Excel. While it appeared no different in the control panel, it did fix the double-click issue. So if all it takes is this simple fix after an update, I can live with that. What I am wondering is: Has anyone seen any other problems related to having multiple versions of Office installed?

  Read the article

• ISPconfig3 + CentOS 6.2 , confused on how to move forward after initial install?

  - by Damainman

  I installed ISPCONFIG3 on centos 6.2 using the great guide on howtoforge.com. Everything is up and running and I can access ISPCONFIG via a browser. However I am not sure how to move forward with the initial setup so I can setup the very first account and get my website live. Details: Only have 1 server, the centos+ispconfig is running on a virtual machine of XEN XCP. I setup the server name to be server1.mydomain.com. I only have 2 usable ips. I plan to use them as follows: xx.xx.xx.01 : For my website and the websites of all accounts I add. xx.xx.xx.02 : For ns1.mydomain.com and ns2.mydomain.com (Yea I know they should be different ips at different locations, but this is what I have to work with at the moment.... ) I registered the nameservers at my registrar with the .02 ip. I want to use bind and ISPconfig to run the DNS on my server itself and not via my registrar. Right now if I go to the .01 IP it shows the centos+apache successful install page. So to break it down basically I am not sure where to start when it comes to: (What to consider and what to do to setup the first domain on the server) Telling bind to use the name server domains with .02. Setting up my First website(which will be my main website) in ISPconfig so mydomain.com resolves properly to my server. Make it so when you go to the .01 IP, it either redirects or shows the contents of my main website. (If this can't be done, then any advice is appreciated) Making sure that when I add a new domain, it automatically puts in the proper information for the domain so it points to the right mail, database, dns, entry. If I overlooked a tutorial then please feel free to let me know, and any advice would be greatly appreciated. Some of the tutorials I found were not specific to doing everything on only one server with Centos+Apache+Bind. Right now all I did was install centos and install ISPconfig3. Trying to move forward correctly so I don't mess up everything I did by not knowing what to do. Thank you in advance!!

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• Graphics card artifacting

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 @ stock clocks 3x 2GB DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) My graphics card started artifacting while I was playing a game. It artifacted, the display blinked, then I got an NVIDIA driver has crashed and recovered message. Kept going, more artifacts, another crash, but this time my display blanked out and I couldn't do anything. Restarted my computer - artifacting is in the BIOS - got to Windows 7 but it BSOD'd before I could even log in. I restarted the computer again - artifacts cleared themselves out and I managed to get to Win7, but it soon started blinking in and out and artifacting again. Checked the card temps and they're well within range. (50 idle, 70 full load) The ambient temperature here is about 80-85F with high humidity. Tried Safe Mode and it still froze up/BSOD'd. Already tried the following to fix this problem: - Reseat the graphics card and swapped in a different slot. - Removed cover on card and sprayed with compressed air to clean it out. - Swapped around memory and/or went with only using one stick at a time. - Underclocked card I called EVGA Tech Support and they said that the voltage on the 12V rail of my Corsair AX750 PSU was on the high end of the "acceptable" range (12.4V, highest within acceptable range is 12.6V - optimal is obviously 12V). They gave me an RMA number anyway, but I want to get a second opinion from you all before I send this thing off, as shipping from where I live to EVGA is kind of pricey. This PSU is only 6 months old. So that I don't have to play RMA tag, which case would be most likely? I'm strapped for cash at the moment so I want to reduce the amount of RMAs I have to do since shipping is expensive here. Is there any surefire way to test to see if it's really the graphics card or the PSU? I tried unplugging any devices that were connected to the 12V rail (except for my SSD and graphics card) as I do have 3 mechanical hard drives, but the voltage for that rail didn't drop (it remained at 12.4V). I'm fairly sure it isn't the drivers since I'm getting the artifacting at the BIOS too. Right now I'm back in Windows 7 but I don't know for how long until it messes up again. Any ideas?

  Read the article

• Set up lnux box for hosting a-z [apache mysql php ssl]

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

  Read the article

• recommendations for efficient offsite remote backup solution of vm's

  - by senorsmile

  I am looking for recommendations for backing up my current 6 vm's(and soon to grow to up to 20). Currently I am running a two node proxmox cluster(which is a debian base using kvm for virtualization with a custom web front end to administer). I have two nearly identical boxes with amd phenom II x4's and asus motherboards. Each has 4 500 GB sata2 hdd's, 1 for the os and other data for the proxmox install, and 3 using mdadm+drbd+lvm to share the 1.5 TB's of storage between the two machines. I mount lvm images to kvm for all of the virtual machines. I currently have the ability to do live transfer from one machine to the other, typically within seconds(it takes about 2 minutes on the largest vm running win2008 with m$ sql server). I am using proxmox's built-in vzdump utility to take snapshots of the vm's and store those on an external harddrive on the network. I then have jungledisk service (using rackspace) to sync the vzdump folder for remote offsite backup. This is all fine and dandy, but it's not very scalable. For one, the backups themselves can take up to a few hours every night. With jungledisk's block level incremental transfers, the sync only transfers a small portion of the data offsite, but that still takes at least a half an hour. The much better solution would of course be something that allows me to instantly take the difference of two time points (say what was written from 6am to 7am), zip it, then send that difference file to the backup server which would instantly transfer to the remote storage on rackspace. I have looked a little into zfs and it's ability to do send/receive. That coupled with a pipe of the data in bzip or something would seem perfect. However, it seems that implementing a nexenta server with zfs would essentially require at least one or two more dedicated storage servers to serve iSCSI block volumes (via zvol's???) to the proxmox servers. I would prefer to keep the setup as minimal as possible (i.e. NOT having separate storage servers) if at all possible. I have also briefly read about zumastor. It looks like it could also do what I want, but it appears to have halted development in 2008. So, zfs, zumastor or other?

  Read the article

• What Sort of Server Setup Am I Likely to Need? - School A/V streaming

  - by DeathMagus

  My prior experience with servers has generally been limited to home file-sharing servers, low-traffic web-servers, and the like. This leaves me with the technical knowledge of how to set up a system, but little experience in terms of scaling said system. My current project, however, has me as the technical lead in setting up a school for online audio and video streaming. The difficulty I'm running into is that I don't quite have the experience to guess what they'll need, and they don't have the experience to tell me - so I've tried to ask as many pertinent questions about what they want to do with their server, and here's what I found out: About 1000 simultaneous users, and hoping to expand (possibly significantly) Both video and audio streaming, at obviously the highest quality possible Support for both live and playlist-based streaming. Probably only one channel, but as it's an educational opportunity, I imagine letting them have a few more wouldn't hurt. No word on whether they're locked into Windows or whether Linux is acceptable. Approximate budget - $7000. It may actually be about $2k less than this, because of a mishap with another technology firm (they ordered a $7000 DV tape deck for some reason, and now the company wants them to pay a 30% restocking fee). The tentative decisions I've already made: I'm planning on using Icecast 2 for my streaming server, fed by VLC Shoutcast encoding. Since the school already has a DMZ set up, I plan on placing the Icecast server in there, and feeding it through their intranet from a simple workstation computer in their studios. This system isn't in any way mission critical - it's an education tool (they're a media magnet school), so I figure redundancy is not worthwhile to them from a cost:benefit perspective. What I don't know is this: How powerful of a server will I need? What is likely to be my major throttle - bandwidth? How can I mitigate that? Will I need anything special for the encoding workstation other than professional video and audio capture cards and a copy of VLC? Are there any other considerations that I'm simply missing? Thanks a lot for any help - if there's more information you need, let me know and I'll tell you all I can.

  Read the article

• Spotlight Infinite Indexing issue (external data drive)

  - by Manca Weeks

  This is an external drive, formerly a boot drive which is now in use only to access music files (sibelius, audio, midi, live, logic etc.) without transferring the data into a new boot system, partly because of the issue I am about to describe, but mostly because the majority of the data is mainly there for archival purposes. The user is a composer and prominent musician and needs to be able to rehash the data at will. I have tried several things - here is a list: - make complete filesystem clone with antonio diaz's ddrescue - run Disk Warrior on copy, repair whatever errors occurred - wipe out all ACLs on entire drive - set all permissions to the same value - wide open 777 - remove any system data (applications, system files, including hidden files to the best of my knowledge) by selecting only non-system/app data and using Carbon Copy Cloner to put only the data of interest onto a newly formatted drive - transfer data to newly formatted drive folder by folder, resetting the spotlight index in between adding each to observe for issues (interesting here is that no issues occurred except for in Documents folder - when I transferred only the Documents folder to a newly formatted drive on its own - no trouble. It appears almost as thought it may not be the content but the quantity or specific combination of data that results in problems) - use DataRescue to transfer the data to yet another newly formatted drive to expose any missed hidden files Between each of the above steps I stopped Spotlight (search for anything beginning with md in Activity Monitor - All Processes and quitting it), deleted the .Spotlight-V100 directory from the affected drive. Restart Splotlight indexing by adding drive to Spotlight privacy list and removing it. In each case the same issue occurs - Spotlight begins indexing normally (or so it seems), then the index estimated time increases, usually to 4 hours remaining. This is where it gets stuck and continues to predict 4 hours remaining but never finishes. Sometimes I can't eject the drive and have to quit the md.. processes from Activity Monitor to be able to eject the drive without Force Eject. Once I disconnect the drive after the 4 hours remaining situation - if I reattach it, Spotlight forever estimates remaining time and never gets going again. So there it is. It is apparently not a filesystem issue, not a permissions issue and not tied to any particular piece of hardware or protocol (used USB and FW drives). I have tried this on several machines (3 to be precise) and in 10.5.8 and 10.6.5. Simply disabling Spotlight on this volume is not an option because the owner has no clue where things are as the data on the volume dates back to music projects and compositions from 2003 and before. He needs to be able to query for results. Anyone got any ideas? Thanks, M

  Read the article

• Both nginx and php5-fpm init.d startup scripts are non-functional and returning no errors..? But they used to work perfectly

  - by Ollie Treend

  I have been using nginx and php5-fpm on my Ubuntu box for a while now. Everything has been configured and setup correctly, and it ran like a charm. I have been keeping the packages updated & upgraded as usual, but haven't touched the nginx OR php5-fpm config files at all (thus I'm pretty sure this isn't my fault... ) Basically, I noticed nginx wasn't running as it should be. I ran the command sudo service nginx start, and the script did nothing. The same thing happens when trying to do anything - start, stop, restart or reload. This also happens for the "php5-fpm" init script - although all other init scripts seem to be functioning correctly. When trying to start nginx OR php5-fpm, this is what happens: root@HAL:/etc# service php5-fpm start root@HAL:/etc# I can't understand what is going wrong. The script isn't returning errors, but similarly it isn't starting the daemon or reporting success as usual. For reference, both installations are from the official nginx and php5-fpm PPAs. The fact that both started doing this at the same time has thrown me - since they are both unrelated packages. I have since purged both sets of packages from my system with apt-get purge ... and also apt-get remove --purge ... both of which have successfully removed the packages, their config files, and their init.d startup scripts. After having reinstalled nginx, I now have a functioning startup script again - I can start the web server as usual. However, php5-fpm is still experiencing the strange premature exiting of the startup script.. and I really can't figure out what's causing it. I have no idea what caused this to occur initially, but have managed to fix nginx. I now need to fix the php5-fpm startup script. If anybody could shed some light on this situation, I would be very grateful! The chances are both these issues are related - and they were caused by me doing something stupid. But now I need to fix it. This time I was lucky - because these problems are just on my development server. But I have 2 other live servers which are configured in a similar way, and I am worried the same thing will happen to these two as well! Has anybody else come across this? Do you have any words of advice? Thank you

  Read the article

• How can I make subversion reset the stored passwords/users and remember my authentication credential

  - by NicDumZ

  Hello folks! Background: I used to have everything working just fine on my fresh install: $ svn co https://domain:443/ test1 Error validating server certificate for 'https://domain:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! Certificate information: - Hostname: **REMOVED** - Valid: **REMOVED** - Issuer: **REMOVED** - Fingerprint: **checked with issuer and REMOVED** (R)eject, accept (t)emporarily or accept (p)ermanently? p Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz-machine-hostname': Authentication realm: <https://domain:443> Subversion repository Username: nicdumz Password for 'nicdumz': # proceeds to checkout correctly $ svn co https://domain:443/ test2 # checkouts nicely, without asking for my password. At some point I needed to commit stuff using a different account. So I did that $ svn ci --username other.user Authentication realm: <https://domain:443> Subversion repository Password for 'other.user': # works fine But since then, everytime I want to commit as 'nicdumz' (default user, all repos have been checked-out with that user), it prompts me for my password: $ svn ci Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz': Hey come on, why :) The same happens if I want a fresh checkout, since read-access is also protected. So I tried fixing the issue by myself. I read around that ~/.subversion/auth was storing credentials, so I removed it from the way: $ cd ~/.subversion $ mv auth oldauth $ mkdir auth It seemed to work at first, because svn had forgotten about certificate validation: $ svn co https://domain:443/ test3 Error validating server certificate for 'https://domain:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! Certificate information: - Hostname: **REMOVED** - Valid: **REMOVED** - Issuer: **REMOVED** - Fingerprint: **checked with issuer and REMOVED** (R)eject, accept (t)emporarily or accept (p)ermanently? p Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz-machine-hostname': Authentication realm: <https://domain:443> Subversion repository Username: nicdumz Password for 'nicdumz': # proceeds to checkout correctly $ svn up Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz': What? how is this happening? If you have suggestions to investigate more about the behaviour, I am very interested. If I'm correct, there is no way to do a verbose svn up or anything of the like, so I'm not sure should I go for investigation. Oh, and for what it's worth: $ svn --version svn, version 1.6.6 (r40053) compiled Oct 26 2009, 06:19:08 Copyright (C) 2000-2009 CollabNet. Subversion is open source software, see http://subversion.tigris.org/ This product includes software developed by CollabNet (http://www.Collab.Net/). The following repository access (RA) modules are available: * ra_neon : Module for accessing a repository via WebDAV protocol using Neon. - handles 'http' scheme - handles 'https' scheme * ra_svn : Module for accessing a repository using the svn network protocol. - with Cyrus SASL authentication - handles 'svn' scheme * ra_local : Module for accessing a repository on local disk. - handles 'file' scheme * ra_serf : Module for accessing a repository via WebDAV protocol using serf. - handles 'http' scheme - handles 'https' scheme

  Read the article

< Previous Page | 416 417 418 419 420 421 422 423 424 425 426 427  | Next Page >